To investigate the ballistic performance and damage characteristics of quasi threedimensional（3D） needle-punched Cf/SiC composites prepared by chemical vapor infiltration（CVI）,penetration experiments were conducte...To investigate the ballistic performance and damage characteristics of quasi threedimensional（3D） needle-punched Cf/SiC composites prepared by chemical vapor infiltration（CVI）,penetration experiments were conducted by using 7.62 mm armor piercing incendiary（API）.Macro and micro fracture morphologies were then observed on recycled targets.The results show that the protection coefficient of 3D Cf/SiC composites is 2.54.High porosity and many micro thermal stress cracks may directly lead to the lower ballistic performance.Flat fracture morphology was observed on the crater surface.The low dynamic fracture strength along layer direction may be attributed to the voids and microcracks caused by residual thermal stress.The damage characteristics of Cf/Si C composites include matrix cracking,fiber bundle cracking,interfacial debonding,fiber fracture,and fiber bundle pull-out.And interfacial debonding and fiber fracture may play major roles in energy absorption.展开更多
Ceramic matrix composites (CMCs) are the preferred materials for solving advanced aerospace high-temperature structural components;it has the comprehensive advantages of higher temperature (~1500˚C) and low density. I...Ceramic matrix composites (CMCs) are the preferred materials for solving advanced aerospace high-temperature structural components;it has the comprehensive advantages of higher temperature (~1500˚C) and low density. In service environments, CMCs exhibit complex damage mechanisms and failure modes, which are affected by constituent materials, meso-architecture and inhere defects. In this paper, the in-plane tensile mechanical behavior of a plain-woven SiCf/SiC composite at room and elevated temperatures was investigated, and the factors affecting the tensile strength of the material were discussed in depth. The results show that the tensile modulus and strength of SiCf/SiC composites at high temperature are lower, but the fracture strain increases and the toughness of the composites is enhanced;the stitching holes significantly weaken the tensile strength of the material, resulting in the material is easy to break at the cross-section with stitching holes.展开更多
Ceramic matrix composites(CMCs)structural components encounter the dual challenges of severe mechanical conditions and complex electromagnetic environments due to the increasing demand for stealth technology in aerosp...Ceramic matrix composites(CMCs)structural components encounter the dual challenges of severe mechanical conditions and complex electromagnetic environments due to the increasing demand for stealth technology in aerospace field.To address various functional requirements,this study integrates a biomimetic strategy inspired by gradient bamboo vascular bundles with a novel dual-material 3D printing approach.Three distinct bamboo-inspired structural configurations Cf/SiC composites are designed and manufactured,and the effects of these different structural configurations on the CVI process are analyzed.Nanoindentation method is utilized to characterize the relationship between interface bonding strength and mechanical properties.The results reveal that the maximum flexural strength and fracture toughness reach 108.6±5.2 MPa and 16.45±1.52 MPa m1/2,respectively,attributed to the enhanced crack propagation resistance and path caused by the weak fiber-matrix interface.Furthermore,the bio-inspired configuration enhances the dielectric loss and conductivity loss,exhibiting a minimum reflection loss of−24.3 dB with the effective absorption band of 3.89 GHz.This work introduces an innovative biomimetic strategy and 3D printing method for continuous fiber-reinforced ceramic composites,expanding the application of 3D printing technology in the field of CMCs.展开更多
Model composites consisting of Si C fiber embedded inβ-Yb_(2)Si_(2)O_(7) matrix were processed by Spark Plasma Sintering method and the feasibility of tunable Si Cf/Yb_(2)Si_(2)O_(7) interface in Si C-based CMCs were...Model composites consisting of Si C fiber embedded inβ-Yb_(2)Si_(2)O_(7) matrix were processed by Spark Plasma Sintering method and the feasibility of tunable Si Cf/Yb_(2)Si_(2)O_(7) interface in Si C-based CMCs were estimated.Weak and strengthened Si Cf/Yb_(2)Si_(2)O_(7) interfaces were achieved by adjusting sintering temperatures.The indentation crack test and fiber push out experiments clearly demonstrated the different debonding mechanisms in the samples.Weak interfaces sintered at 1200 and 1250℃exhibited crack deflection at interface in indentation test.Their low debond energy at the interface,which were comparable to those of Py C or BN,satisfied the well-recognized interfacial debond and crack deflection criteria for CMCs.The interface was strengthened by atomic bonding in model composite sintered at 1450℃,leading to crack penetrating into Si C fiber and high debond energy.The strong interface may be promising in Si Cf/Si C CMC to withstand higher combustion temperature,because Yb_(2)Si_(2)O_(7) will provide plastic deformation capacity,which would serve as weak interphase for crack deflection and energy dissipation.Therefore,it is possible to design the capability of Si C_(f)/RE_(2)Si_(2)O_(7) interface for different requirements by adjusting interfacial strength or debond energy to reach optimal mechanical fuse mechanism in SiC_(f)/SiC CMC.展开更多
Designing materials with both structural load-bearing capacity and broadband electromagnetic(EM)wave absorption properties remains a significant challenge.In this work,SiOC/SiC/SiO_(2)composite with gyroid structures ...Designing materials with both structural load-bearing capacity and broadband electromagnetic(EM)wave absorption properties remains a significant challenge.In this work,SiOC/SiC/SiO_(2)composite with gyroid structures were prepared through digital light processing(DLP)3D printing,polymer-derived ceramics(PDCs),chemical vapor infiltration(CVI),and oxidation technologies.The incorporation of the CVISiC phase effectively increases the dissipation capability,while the synergistic interaction between the gyroid structure and SiO_(2)phase significantly improves impedance matching performance.The SiOC/SiC/SiO_(2)composite achieved a minimum reflection loss(RL min)of-62.2 d B at 4.3 mm,and the effective absorption bandwidth(EAB)covered the X-band,with a thickness range of 4.1 mm-4.65 mm.The CST simulation results explain the broadband and low-frequency absorption characteristics,with an EAB of 8.4 GHz(9.6-18 GHz)and an RL min of-21.5 dB at 5 GHz.The excellent EM wave attenuation performance is associated primarily with polarization loss,conduction loss,the gyroid structure's enhancement of multiple reflections and scattering of EM waves,and the resonance effect between the structural units.The SiOC/SiC/SiO_(2)composite also demonstrated strong mechanical properties,with a maximum compressive failure strength of 31.6 MPa in the height direction.This work opens novel prospects for the development of multifunctional structural wave-absorbing materials suitable for broadband microwave absorption and load-bearing properties.展开更多
The research on high-performance electromagnetic wave absorption materials with high-temperature and oxidative stability in extreme environments is gaining popularity.Herein,the lightweight silicon carbide nanowires(S...The research on high-performance electromagnetic wave absorption materials with high-temperature and oxidative stability in extreme environments is gaining popularity.Herein,the lightweight silicon carbide nanowires(SiC_(nws))/SiC composites are fabricated with in-situ SiC interface on one-dimensional oriented SiC_(nws)skeleton,which collaborative configuration by 3D printing and freeze casting assembly.The con-structed porous structure optimizes the impedance matching degree and scattering intensity,the maximum effective absorption bandwidth(EAB_(max))of 5.9 GHz and the minimum reflection loss(RL_(min))of−41.4 dB can be realized.Considering the inherent oxidation resistance of SiC,the composites present well-maintained absorption performance at 600℃.Even at 1100℃,the EAB_(max)of 4.9 GHz and RLmin of−30.4 dB also demonstrate the high-temperature absorption stability of the composites,indicating exceptional wave absorption properties and thermal stability.The slight attenuation can be attributed to the decrease in impedance matching capability accompanying the elevated dielectric constant.This work clarifies the impact of structure and component synergy on wave absorption behavior,and offers a novel approach to producing high-performance and high-temperature resistance ceramic-based electromagnetic wave absorption materials suitable for extreme environments.展开更多
The SiCf/SiC composites containing PyC interphase were prepared by chemical vapor infiltration process. The influences of thermal oxidation on the complex permittivity and microwave absorption properties of Si Cf/Si C...The SiCf/SiC composites containing PyC interphase were prepared by chemical vapor infiltration process. The influences of thermal oxidation on the complex permittivity and microwave absorption properties of Si Cf/Si C composites were investigated in the frequency range of 8.2-12.4 GHz. Both the real and imaginary parts of the complex permittivity decreased after thermal oxidation. The composites after 100 h thermal oxidation showed that reflection loss exceeded-10 d B in the frequency of 9.7-11.9 GHz and the minimum value was-11.4 d B at 11.0 GHz. The flexural strength of composites decreased but fracture behavior was improved obviously after thermal oxidation. These results indicate that the SiCf/SiC composites containing PyC interphase after thermal oxidation possess good microwave absorbing property and fracture behavior.展开更多
In a high heat flux ablative environment,the surface temperature of aircraft rises rapidly,leading to traditional high thermal conductivity materials being ineffective at protecting internal metal components.In this s...In a high heat flux ablative environment,the surface temperature of aircraft rises rapidly,leading to traditional high thermal conductivity materials being ineffective at protecting internal metal components.In this study,continuous carbon fiber reinforced Li_(2)O-Al_(2)O_(3)-SiO_(2)(C_(f)/LAS)glass ceramic composites doped with SiC particles(SiC_(p))were prepared by slurry immersion winding and hot pressing sintering.Effect of matrix crystallinity on ablative properties of the composites under ultra-high heat flux was investigated.By utilizing heat absorption and low thermal conductivity characteristics associated with SiO_(2)gasification within composite materials,both surface and internal temperatures of these materials are effectively reduced,thereby ensuring the safe operation of aircraft and electronic devices.Results indicate that the average linear ablation rate of composites doped with 10%(in mass)of SiC_(p)significantly decreases at a heat flux of 20 MW/m^(2).Transmission electron microscope observation reveals that the doped glass matrix exhibits increased crystallinity,reduced internal stress,and minimized lattice distortion,thereby enhancing the composites’high-temperature performance.However,excessive SiC_(p)doping leads to reduced crystallinity and deteriorated ablation performance.Ultimately,the average linear ablation rate of C_(f)/LAS composites with 10%(in mass)SiC_(p)at 20 MW/m^(2)heat flux is comparable to that of commercial carbon/carbon composites,accompanied by providing lower thermal conductivity and higher bending strength.This novel high-performance C_(f)/LAS composite is cost-effective,short-cycled,and suitable for mass production,offering promising potential for widespread application in ablation-resistant components of hypersonic vehicles.展开更多
A practical process method for precise integration of SiC_(f)/SiC composite(CMC)and a Ni-based superalloy(K403)was proposed in this study.It involves Nb coating pretreatment of the CMC via the chemical vapor depositio...A practical process method for precise integration of SiC_(f)/SiC composite(CMC)and a Ni-based superalloy(K403)was proposed in this study.It involves Nb coating pretreatment of the CMC via the chemical vapor deposition(CVD)at 1000℃and subsequent integral precision casting between the pretreated CMC and the K403 superalloy melt.The method solves the difficulty for the dissimilar material to be cast together,forming a robust bonding interface with an average shear strength of 94.8 MPa at room temperature.During the pretreatment process,the Nb reacted with the CMC,forming a reactive coating with the microstructure composed of NbC,Nb2C and Nb5Si3 phases.In the following integral casting,the Nb reactive coating effectively blocked detrimental graphitization reaction between the Ni element in the superalloy melt and the CMC,and mitigated the interface thermal stress generated by both the mismatch of thermal expansion coefficients and temperature difference,resulting in the increase of interfacial strength.The typical interfacial microstructure consists of the CMC,NbC,NbSi_(2)/NbC,SiC,NbSi_(2),Nb_(2)C,Nb_(5)Si_(3),Al_(4)C_(3),Nb_(2)Al/γ/γ'and MC(M=W,Mo,Ti).A formula for estimating the interfacial thermal stress of an integrated cast was derived.展开更多
Non-isothermal aging(NIA)treatments have presented significant advantages in improving the comprehensive performance and aging hardening efficiency of the 7000 series aluminum alloys,but there is no attention paid to ...Non-isothermal aging(NIA)treatments have presented significant advantages in improving the comprehensive performance and aging hardening efficiency of the 7000 series aluminum alloys,but there is no attention paid to their composites.This study takes a linear heating aging process as an example to reveal the precipitation behaviors of a 15 vol.%SiC/7085Al composite as well as its impact on mechanical properties using differential scanning calorimetry,transmission electron microscopy,small-angle neutron scattering,hardness measurements,and tensile testing.The results indicated the formation of GP(Ⅰ,Ⅱ)zones,η’andηprecipitates in sequence,leading to the hardness and strength initially increasing and then decreasing with rising NIA temperatures.The maximums were reached at 183℃,corresponding to the appearance ofη’precipitates in large quantities.Owing to the rapid temperature rise during the NIA process,the precipitates entered the coarsening and redissolution stage before they were entirely formed,resulting in reduced peak strength compared to the T6 treatment.The composite exhibited a more significant reduction in strength than the 7085Al alloy because:(i)the annihilation of vacancies suppressed the formation of GPII zones,thereby weakening their transition toη’precipitates;(ii)quenching dislocations promoted the coarsening of precipitates.An improved NIA process,incorporating both heating and cooling aging treatments,was effectively designed with the assistance of in-situ SANS technology to address this issue,which allows for achieving strength comparable to that after the T6 treatment with only 15%of the aging time consumption.This research fills the gap in investigating the NIA precipitation behaviors of aluminum matrix composites,providing guidance for the formulation of NIA schedules.展开更多
A novel Y_(3)Si_(2)C_(2)material was synthesized at a relatively low temperature(900℃)using a molten salt method for the first time,and subsequently used as the joining material for carbon fiber reinforced SiC(Cf/SiC...A novel Y_(3)Si_(2)C_(2)material was synthesized at a relatively low temperature(900℃)using a molten salt method for the first time,and subsequently used as the joining material for carbon fiber reinforced SiC(Cf/SiC)composites.The sound near-seamless joints with no obvious remaining interlayer were obtained at 1600℃using an electric field-assisted sintering technique(FAST).During joining,a liquid phase was formed by the eutectic reaction among Y_(3)Si_(2)C_(2),γ(Y–C)phase,and SiC,followed by the precipitation of SiC particles.The presence of the liquid promoted the sintering of newly formed SiC particles,leading to their complete consolidation with the Cf/SiC matrix.On the other hand,the excess of the liquid was pushed away from the joining area under the effect of a uniaxial pressure of 30 MPa,leading to the formation of the near-seamless joints.The highest shear strength(Ä)of 17.2±2.9 MPa was obtained after being joined at 1600℃for 10 min.The failure of the joints occurred in the Cf/SiC matrix,indicating that the interface was stronger than that of the Cf/SiC matrix.The formation of a near-seamless joint minimizes the mismatch of thermal expansion coefficients and also irradiation-induced swelling,suggesting that the proposed joining strategy can be potentially applied to SiC-based ceramic matrix composites(CMCs)for extreme environmental applications.展开更多
Three-dimensional finite element physical models considering the layered distribution of materials at the interface were developed to study the effect of the coating system on distributions of thermal residual stresse...Three-dimensional finite element physical models considering the layered distribution of materials at the interface were developed to study the effect of the coating system on distributions of thermal residual stresses in SiCf/Ti2AlNb composites.Two coating systems were comparatively studied,namely C coating and C/Mo duplex-coating.The thermal residual stresses after 1 080 ℃/1 h solution treatment and 800 ℃/20 h ageing treatment in the composites were also analyzed.The experimental results show that Mo coating can decrease thermal residual stress magnitude in the matrix.However,it would increase the thermal residual stresses in the interfacial reaction layer of TiC.The change of radial thermal residual stress in TiC layer is inconspicuous after solid solution and ageing treatment,but the hoop and axial thermal residual stresses increase obviously.However,the heat treatment can obviously reduce hoop and axial thermal residual stresses of the matrix,which is benefit to restrain the initiation and propagation of cracks in the matrix.展开更多
BN interphase was successfully synthesized on SiC fiber fabrics by dip-coating process using boric acid and urea as precursors under N2 atmosphere. The morphology of BN interphase was observed by SEM, and the structur...BN interphase was successfully synthesized on SiC fiber fabrics by dip-coating process using boric acid and urea as precursors under N2 atmosphere. The morphology of BN interphase was observed by SEM, and the structure was characterized by XRD and FT-IR spectra. The SiCf/SiC composites with dip-coated BN interphase were fabricated by chemical vapor infiltration （CVI） process, and the effects ofBN interphase on the mechanical properties of composites were investigated. The results show that the SiC fibers are fully covered by BN interphase with smooth surface and turbostratic structure （t-BN）, and the thickness is about 0.4 μm. The flexural strengths of SiCf/SiC composites with and without BN interphase are about 180 and 95 MPa, respectively. Compared with the as-received SiCf/SiC composites, the composites with BN interphase exhibit an obvious toughened fracture behavior. From the microstructural analysis, it can be confirmed that the BN interphase plays a key part in protecting the fibers from chemical attack during matrix infiltration and weakening interfacial bonding, which can improve the mechanical properties of SiCf/SiC composites remarkably.展开更多
The properties and structures of 3D-Cf/ SiC composites prepared by rapid precursor infiltration pyrolysis process were studied.PCS solution was infiltrated into 3D-carbon fiber perform in vacuum,then these performs we...The properties and structures of 3D-Cf/ SiC composites prepared by rapid precursor infiltration pyrolysis process were studied.PCS solution was infiltrated into 3D-carbon fiber perform in vacuum,then these performs were dried at room temperature and pyrolyzed with three kinds of heating rate,3 900 min,1 500 min and 1 000 min respectively.The distinction of 3D-Cf/SiC samples fabricated at three kinds of heating rate was not obvious.Bending strength of sample at 1 000 min heating rate was 762.5 MPa,and a little better than the others.Three samples at various heating rate had similar micro-graph of fracture surface and fracture toughness.The research results show that mechanics performances of Cf/SiC composites did not decrease when heating rate was properly increased.展开更多
Filler materials of(ZrB_2-SiC-B_4C-YAG) composite were developed for gas tungsten arc welding(GTAW) of the ZrB_2-SiC and Cf-SiC based composites to themselves and to each other. Reaction with filler material,porosity ...Filler materials of(ZrB_2-SiC-B_4C-YAG) composite were developed for gas tungsten arc welding(GTAW) of the ZrB_2-SiC and Cf-SiC based composites to themselves and to each other. Reaction with filler material,porosity and cracks were not observed at weld interfaces of all the joints. Penetration of filler material in to voids and pores existing in the Cf-SiC composites was observed. Average shear strength of 25.7 MPa was achieved for joints of Cf-SiC composites. By incorporation of Cf-SiC(CVD) ground short fibre reinforcement the(ZrB_2-SiC-B_4C-YAG) composite was machinable with tungsten carbide tool. The joint and machined composites were resistance to oxidation and thermal shock when exposed to the oxy-propane flame at 2300℃ for 300s. The combination of(ZrB_2-SiC-B_4C-YAG) and Cf-SiC based composites can be used for making parts like thermal protection system or nozzles for high temperature applications.展开更多
To improve the oxidation resistance of carbon/carbon composites,ZrB2-MoSi2/SiC coating on the carbon/carbon substrate was prepared.The inner coating of SiC was prepared by pack cementation and the outer coating of ZrB...To improve the oxidation resistance of carbon/carbon composites,ZrB2-MoSi2/SiC coating on the carbon/carbon substrate was prepared.The inner coating of SiC was prepared by pack cementation and the outer coating of ZrB2-MoSi2 was prepared by slurry painting.The phase compositions and microstructures of the coating were characterized by XRD and SEM,respectively.The preparation and the high temperature oxidation property of the coated composites were investigated.The results show that the outer coating of carbon/carbon composites is composed of ZrB2,MoSi2 and SiC phases.The mass losses of the ZrB2-MoSi2/SiC coated samples with SiC nano-whiskers after 30 h and 10 h of oxidation at 1 273 K and 1 773 K were,respectively,5.3% and 3.0%.The ZrB2-MoSi2/SiC coated samples exhibit self-sealing performance and good oxidation resistance at high temperature.展开更多
C/SiC/MoSi2-SiC-Si oxidation protective multilayer coating for carbon/carbon （C/C） composites was prepared by pack cementation and slurry method. The microstructure, element distribution and phase composition of the...C/SiC/MoSi2-SiC-Si oxidation protective multilayer coating for carbon/carbon （C/C） composites was prepared by pack cementation and slurry method. The microstructure, element distribution and phase composition of the as-received coating were analyzed by scanning electron microscopy （SEM）, energy dispersive X-ray spectroscopy （EDS） and X-ray diffraction （XRD）. The results show that the multilayer coating was composed of MoSi2, SiC and Si. It could effectively protect C/C composites against oxidation for 200 h with the mass loss of 3.25% at 1873 K in static air. The mass loss of the coated C/C composites results from the volatilization of SiO2 and the formation of cracks and bubble holes in the coating.展开更多
To improve the oxidation resistance of C/C composites, a double SiC protective coating was prepared by a two-step technique. Firstly, the inner SiC layer was prepared by a pack cementation technique, and then an outer...To improve the oxidation resistance of C/C composites, a double SiC protective coating was prepared by a two-step technique. Firstly, the inner SiC layer was prepared by a pack cementation technique, and then an outer uniform and compact SiC coating was obtained by low pressure chemical vapor deposition. The microstructures and phase compositions of the coatings were characterized by SEM, EDS and XRD analyses. Oxidation behaviour of the SiC coated C/C composites was also investigated. It was found that the double SiC coating could protect C/C composites against oxidation at 1773 K in air for 178 h with a mass loss of 1.25%. The coated samples also underwent thermal shocks between 1773 K and room temperature 16 times. The mass loss of the coated C/C composites was only 2.74%. Double SiC layer structures were uniform and dense, and can suppress the generation of thermal stresses, facilitating an excellent anti-oxidation coating.展开更多
The mass of high-speed trains can be reduced using the brake disk prepared with SiC network ceramic frame reinforced 6061 aluminum alloy composite （SiCn/Al）. The thermal and stress analyses of SiCn/Al brake disk dur...The mass of high-speed trains can be reduced using the brake disk prepared with SiC network ceramic frame reinforced 6061 aluminum alloy composite （SiCn/Al）. The thermal and stress analyses of SiCn/Al brake disk during emergency braking at a speed of 300 km/h considering airflow cooling were investigated using finite element （FE） and computational fluid dynamics （CFD） methods. All three modes of heat transfer （conduction, convection and radiation） were analyzed along with the design features of the brake assembly and their interfaces. The results suggested that the higher convection coefficients achieved with airflow cooling will not only reduce the maximum temperature in the braking but also reduce the thermal gradients, since heat will be removed faster from hotter parts of the disk. Airflow cooling should be effective to reduce the risk of hot spot formation and disc thermal distortion. The highest temperature after emergency braking was 461 °C and 359 °C without and with considering airflow cooling, respectively. The equivalent stress could reach 269 MPa and 164 MPa without and with considering airflow cooling, respectively. However, the maximum surface stress may exceed the material yield strength during an emergency braking, which may cause a plastic damage accumulation in a brake disk without cooling. The simulation results are consistent with the experimental results well.展开更多
基金Funded by the National Natural Science Foundation of China(No.51271036)
文摘To investigate the ballistic performance and damage characteristics of quasi threedimensional（3D） needle-punched Cf/SiC composites prepared by chemical vapor infiltration（CVI）,penetration experiments were conducted by using 7.62 mm armor piercing incendiary（API）.Macro and micro fracture morphologies were then observed on recycled targets.The results show that the protection coefficient of 3D Cf/SiC composites is 2.54.High porosity and many micro thermal stress cracks may directly lead to the lower ballistic performance.Flat fracture morphology was observed on the crater surface.The low dynamic fracture strength along layer direction may be attributed to the voids and microcracks caused by residual thermal stress.The damage characteristics of Cf/Si C composites include matrix cracking,fiber bundle cracking,interfacial debonding,fiber fracture,and fiber bundle pull-out.And interfacial debonding and fiber fracture may play major roles in energy absorption.
文摘Ceramic matrix composites (CMCs) are the preferred materials for solving advanced aerospace high-temperature structural components;it has the comprehensive advantages of higher temperature (~1500˚C) and low density. In service environments, CMCs exhibit complex damage mechanisms and failure modes, which are affected by constituent materials, meso-architecture and inhere defects. In this paper, the in-plane tensile mechanical behavior of a plain-woven SiCf/SiC composite at room and elevated temperatures was investigated, and the factors affecting the tensile strength of the material were discussed in depth. The results show that the tensile modulus and strength of SiCf/SiC composites at high temperature are lower, but the fracture strain increases and the toughness of the composites is enhanced;the stitching holes significantly weaken the tensile strength of the material, resulting in the material is easy to break at the cross-section with stitching holes.
基金supported by The National Key Research and Development Program of China(No.2019YFB1901001).
文摘Ceramic matrix composites(CMCs)structural components encounter the dual challenges of severe mechanical conditions and complex electromagnetic environments due to the increasing demand for stealth technology in aerospace field.To address various functional requirements,this study integrates a biomimetic strategy inspired by gradient bamboo vascular bundles with a novel dual-material 3D printing approach.Three distinct bamboo-inspired structural configurations Cf/SiC composites are designed and manufactured,and the effects of these different structural configurations on the CVI process are analyzed.Nanoindentation method is utilized to characterize the relationship between interface bonding strength and mechanical properties.The results reveal that the maximum flexural strength and fracture toughness reach 108.6±5.2 MPa and 16.45±1.52 MPa m1/2,respectively,attributed to the enhanced crack propagation resistance and path caused by the weak fiber-matrix interface.Furthermore,the bio-inspired configuration enhances the dielectric loss and conductivity loss,exhibiting a minimum reflection loss of−24.3 dB with the effective absorption band of 3.89 GHz.This work introduces an innovative biomimetic strategy and 3D printing method for continuous fiber-reinforced ceramic composites,expanding the application of 3D printing technology in the field of CMCs.
基金supported by the National Key R&D Program of China under Grant No.2017YFB0703201Natural Science Foundation of China under Grant No.51772302CAS International Cooperation Key Program under Grant No.174321KYSB20180008。
文摘Model composites consisting of Si C fiber embedded inβ-Yb_(2)Si_(2)O_(7) matrix were processed by Spark Plasma Sintering method and the feasibility of tunable Si Cf/Yb_(2)Si_(2)O_(7) interface in Si C-based CMCs were estimated.Weak and strengthened Si Cf/Yb_(2)Si_(2)O_(7) interfaces were achieved by adjusting sintering temperatures.The indentation crack test and fiber push out experiments clearly demonstrated the different debonding mechanisms in the samples.Weak interfaces sintered at 1200 and 1250℃exhibited crack deflection at interface in indentation test.Their low debond energy at the interface,which were comparable to those of Py C or BN,satisfied the well-recognized interfacial debond and crack deflection criteria for CMCs.The interface was strengthened by atomic bonding in model composite sintered at 1450℃,leading to crack penetrating into Si C fiber and high debond energy.The strong interface may be promising in Si Cf/Si C CMC to withstand higher combustion temperature,because Yb_(2)Si_(2)O_(7) will provide plastic deformation capacity,which would serve as weak interphase for crack deflection and energy dissipation.Therefore,it is possible to design the capability of Si C_(f)/RE_(2)Si_(2)O_(7) interface for different requirements by adjusting interfacial strength or debond energy to reach optimal mechanical fuse mechanism in SiC_(f)/SiC CMC.
基金financially supported by National Natural Science Foundation of China(Grant Nos.12141203,52202083,W2421013)the Natural Science Foundation Project of Shaanxi Province(Grant No.2024JC-YBMS-450)+1 种基金the Sichuan Science and Technology Program(Grant No.2024YFHZ0265)the Open Project of High-end Equipment Advanced Materials and Manufacturing Technology Laboratory(Grant No.2023KFKT0005)。
文摘Designing materials with both structural load-bearing capacity and broadband electromagnetic(EM)wave absorption properties remains a significant challenge.In this work,SiOC/SiC/SiO_(2)composite with gyroid structures were prepared through digital light processing(DLP)3D printing,polymer-derived ceramics(PDCs),chemical vapor infiltration(CVI),and oxidation technologies.The incorporation of the CVISiC phase effectively increases the dissipation capability,while the synergistic interaction between the gyroid structure and SiO_(2)phase significantly improves impedance matching performance.The SiOC/SiC/SiO_(2)composite achieved a minimum reflection loss(RL min)of-62.2 d B at 4.3 mm,and the effective absorption bandwidth(EAB)covered the X-band,with a thickness range of 4.1 mm-4.65 mm.The CST simulation results explain the broadband and low-frequency absorption characteristics,with an EAB of 8.4 GHz(9.6-18 GHz)and an RL min of-21.5 dB at 5 GHz.The excellent EM wave attenuation performance is associated primarily with polarization loss,conduction loss,the gyroid structure's enhancement of multiple reflections and scattering of EM waves,and the resonance effect between the structural units.The SiOC/SiC/SiO_(2)composite also demonstrated strong mechanical properties,with a maximum compressive failure strength of 31.6 MPa in the height direction.This work opens novel prospects for the development of multifunctional structural wave-absorbing materials suitable for broadband microwave absorption and load-bearing properties.
基金supported by the National Key R&D Program of China(No.2022YFB3707700)National Natural Science Foundation of China(No.52302121)+3 种基金Shanghai Sailing Program(No.23YF1454700)Shanghai Natural Science Foundation(No.23ZR1472700)Shanghai Post-doctoral Excellent Program(No.2022664)Shanghai Science and Technology Innovation Action Plan(No.21511104800).
文摘The research on high-performance electromagnetic wave absorption materials with high-temperature and oxidative stability in extreme environments is gaining popularity.Herein,the lightweight silicon carbide nanowires(SiC_(nws))/SiC composites are fabricated with in-situ SiC interface on one-dimensional oriented SiC_(nws)skeleton,which collaborative configuration by 3D printing and freeze casting assembly.The con-structed porous structure optimizes the impedance matching degree and scattering intensity,the maximum effective absorption bandwidth(EAB_(max))of 5.9 GHz and the minimum reflection loss(RL_(min))of−41.4 dB can be realized.Considering the inherent oxidation resistance of SiC,the composites present well-maintained absorption performance at 600℃.Even at 1100℃,the EAB_(max)of 4.9 GHz and RLmin of−30.4 dB also demonstrate the high-temperature absorption stability of the composites,indicating exceptional wave absorption properties and thermal stability.The slight attenuation can be attributed to the decrease in impedance matching capability accompanying the elevated dielectric constant.This work clarifies the impact of structure and component synergy on wave absorption behavior,and offers a novel approach to producing high-performance and high-temperature resistance ceramic-based electromagnetic wave absorption materials suitable for extreme environments.
基金Project(51072165)supported by the National Natural Science Foundation of ChinaProject(201305)supported by the Fund of State Key Laboratory of Solidification Processing,ChinaProjects(2013JK0921,2013JK0922)supported by Shaanxi Provincial Education Department of China
文摘The SiCf/SiC composites containing PyC interphase were prepared by chemical vapor infiltration process. The influences of thermal oxidation on the complex permittivity and microwave absorption properties of Si Cf/Si C composites were investigated in the frequency range of 8.2-12.4 GHz. Both the real and imaginary parts of the complex permittivity decreased after thermal oxidation. The composites after 100 h thermal oxidation showed that reflection loss exceeded-10 d B in the frequency of 9.7-11.9 GHz and the minimum value was-11.4 d B at 11.0 GHz. The flexural strength of composites decreased but fracture behavior was improved obviously after thermal oxidation. These results indicate that the SiCf/SiC composites containing PyC interphase after thermal oxidation possess good microwave absorbing property and fracture behavior.
基金National Natural Science Foundation of China(U23A6014,52103357)。
文摘In a high heat flux ablative environment,the surface temperature of aircraft rises rapidly,leading to traditional high thermal conductivity materials being ineffective at protecting internal metal components.In this study,continuous carbon fiber reinforced Li_(2)O-Al_(2)O_(3)-SiO_(2)(C_(f)/LAS)glass ceramic composites doped with SiC particles(SiC_(p))were prepared by slurry immersion winding and hot pressing sintering.Effect of matrix crystallinity on ablative properties of the composites under ultra-high heat flux was investigated.By utilizing heat absorption and low thermal conductivity characteristics associated with SiO_(2)gasification within composite materials,both surface and internal temperatures of these materials are effectively reduced,thereby ensuring the safe operation of aircraft and electronic devices.Results indicate that the average linear ablation rate of composites doped with 10%(in mass)of SiC_(p)significantly decreases at a heat flux of 20 MW/m^(2).Transmission electron microscope observation reveals that the doped glass matrix exhibits increased crystallinity,reduced internal stress,and minimized lattice distortion,thereby enhancing the composites’high-temperature performance.However,excessive SiC_(p)doping leads to reduced crystallinity and deteriorated ablation performance.Ultimately,the average linear ablation rate of C_(f)/LAS composites with 10%(in mass)SiC_(p)at 20 MW/m^(2)heat flux is comparable to that of commercial carbon/carbon composites,accompanied by providing lower thermal conductivity and higher bending strength.This novel high-performance C_(f)/LAS composite is cost-effective,short-cycled,and suitable for mass production,offering promising potential for widespread application in ablation-resistant components of hypersonic vehicles.
基金the financial support from the Fundamental Research Funds for the Central Universities,China(No.FRF-GF-18-006A)。
文摘A practical process method for precise integration of SiC_(f)/SiC composite(CMC)and a Ni-based superalloy(K403)was proposed in this study.It involves Nb coating pretreatment of the CMC via the chemical vapor deposition(CVD)at 1000℃and subsequent integral precision casting between the pretreated CMC and the K403 superalloy melt.The method solves the difficulty for the dissimilar material to be cast together,forming a robust bonding interface with an average shear strength of 94.8 MPa at room temperature.During the pretreatment process,the Nb reacted with the CMC,forming a reactive coating with the microstructure composed of NbC,Nb2C and Nb5Si3 phases.In the following integral casting,the Nb reactive coating effectively blocked detrimental graphitization reaction between the Ni element in the superalloy melt and the CMC,and mitigated the interface thermal stress generated by both the mismatch of thermal expansion coefficients and temperature difference,resulting in the increase of interfacial strength.The typical interfacial microstructure consists of the CMC,NbC,NbSi_(2)/NbC,SiC,NbSi_(2),Nb_(2)C,Nb_(5)Si_(3),Al_(4)C_(3),Nb_(2)Al/γ/γ'and MC(M=W,Mo,Ti).A formula for estimating the interfacial thermal stress of an integrated cast was derived.
基金support of the Na-tional Key R&D Program of China(No.2021YFA1600700)the Na-tional Natural Science Foundation of China(grant Nos.U22A20114,52322106,52192595,and 52301200)+2 种基金the Project funded by China Postdoctoral Science Foundation(No.2023M733573)CSNS Con-sortium on High-performance Materials of Chinese Academy of Sciences(No.JZHKYPT-2021-01)the Natural Science Foun-dation of Liaoning Province(No.2023-BS-020)。
文摘Non-isothermal aging(NIA)treatments have presented significant advantages in improving the comprehensive performance and aging hardening efficiency of the 7000 series aluminum alloys,but there is no attention paid to their composites.This study takes a linear heating aging process as an example to reveal the precipitation behaviors of a 15 vol.%SiC/7085Al composite as well as its impact on mechanical properties using differential scanning calorimetry,transmission electron microscopy,small-angle neutron scattering,hardness measurements,and tensile testing.The results indicated the formation of GP(Ⅰ,Ⅱ)zones,η’andηprecipitates in sequence,leading to the hardness and strength initially increasing and then decreasing with rising NIA temperatures.The maximums were reached at 183℃,corresponding to the appearance ofη’precipitates in large quantities.Owing to the rapid temperature rise during the NIA process,the precipitates entered the coarsening and redissolution stage before they were entirely formed,resulting in reduced peak strength compared to the T6 treatment.The composite exhibited a more significant reduction in strength than the 7085Al alloy because:(i)the annihilation of vacancies suppressed the formation of GPII zones,thereby weakening their transition toη’precipitates;(ii)quenching dislocations promoted the coarsening of precipitates.An improved NIA process,incorporating both heating and cooling aging treatments,was effectively designed with the assistance of in-situ SANS technology to address this issue,which allows for achieving strength comparable to that after the T6 treatment with only 15%of the aging time consumption.This research fills the gap in investigating the NIA precipitation behaviors of aluminum matrix composites,providing guidance for the formulation of NIA schedules.
基金This study was supported by the National Natural Science Foundation of China(Grant No.11975296)the Natural Science Foundation of Ningbo City(Grant No.2021J199)+3 种基金We would like to recognize the support from the Ningbo 3315 Innovative Teams Program,China(Grant No.2019A-14-C)Peter TATARKO gratefully acknowledges the financial support of the project APVV-17-0328this study was performed as part of the implementation of the project“Building-up Centre for advanced materials application of the Slovak Academy of Sciences”and ITMS project(Grant No.313021T081)supported by the Research&Innovation Operational Programme funded by the ERDF.
文摘A novel Y_(3)Si_(2)C_(2)material was synthesized at a relatively low temperature(900℃)using a molten salt method for the first time,and subsequently used as the joining material for carbon fiber reinforced SiC(Cf/SiC)composites.The sound near-seamless joints with no obvious remaining interlayer were obtained at 1600℃using an electric field-assisted sintering technique(FAST).During joining,a liquid phase was formed by the eutectic reaction among Y_(3)Si_(2)C_(2),γ(Y–C)phase,and SiC,followed by the precipitation of SiC particles.The presence of the liquid promoted the sintering of newly formed SiC particles,leading to their complete consolidation with the Cf/SiC matrix.On the other hand,the excess of the liquid was pushed away from the joining area under the effect of a uniaxial pressure of 30 MPa,leading to the formation of the near-seamless joints.The highest shear strength(Ä)of 17.2±2.9 MPa was obtained after being joined at 1600℃for 10 min.The failure of the joints occurred in the Cf/SiC matrix,indicating that the interface was stronger than that of the Cf/SiC matrix.The formation of a near-seamless joint minimizes the mismatch of thermal expansion coefficients and also irradiation-induced swelling,suggesting that the proposed joining strategy can be potentially applied to SiC-based ceramic matrix composites(CMCs)for extreme environmental applications.
基金Funded by the National Natural Science Foundation of China (No. 51201134)the Key Research Foundation of Yiwu Industrial and Commercial College (No. ZD2020CS414-01)。
文摘Three-dimensional finite element physical models considering the layered distribution of materials at the interface were developed to study the effect of the coating system on distributions of thermal residual stresses in SiCf/Ti2AlNb composites.Two coating systems were comparatively studied,namely C coating and C/Mo duplex-coating.The thermal residual stresses after 1 080 ℃/1 h solution treatment and 800 ℃/20 h ageing treatment in the composites were also analyzed.The experimental results show that Mo coating can decrease thermal residual stress magnitude in the matrix.However,it would increase the thermal residual stresses in the interfacial reaction layer of TiC.The change of radial thermal residual stress in TiC layer is inconspicuous after solid solution and ageing treatment,but the hoop and axial thermal residual stresses increase obviously.However,the heat treatment can obviously reduce hoop and axial thermal residual stresses of the matrix,which is benefit to restrain the initiation and propagation of cracks in the matrix.
基金Project(51072165)supported by the National Natural Science Foundation of ChinaProject(KP201307)supported by the Fund of the State Key Laboratory of Solidification Processing in NWPU
文摘BN interphase was successfully synthesized on SiC fiber fabrics by dip-coating process using boric acid and urea as precursors under N2 atmosphere. The morphology of BN interphase was observed by SEM, and the structure was characterized by XRD and FT-IR spectra. The SiCf/SiC composites with dip-coated BN interphase were fabricated by chemical vapor infiltration （CVI） process, and the effects ofBN interphase on the mechanical properties of composites were investigated. The results show that the SiC fibers are fully covered by BN interphase with smooth surface and turbostratic structure （t-BN）, and the thickness is about 0.4 μm. The flexural strengths of SiCf/SiC composites with and without BN interphase are about 180 and 95 MPa, respectively. Compared with the as-received SiCf/SiC composites, the composites with BN interphase exhibit an obvious toughened fracture behavior. From the microstructural analysis, it can be confirmed that the BN interphase plays a key part in protecting the fibers from chemical attack during matrix infiltration and weakening interfacial bonding, which can improve the mechanical properties of SiCf/SiC composites remarkably.
文摘The properties and structures of 3D-Cf/ SiC composites prepared by rapid precursor infiltration pyrolysis process were studied.PCS solution was infiltrated into 3D-carbon fiber perform in vacuum,then these performs were dried at room temperature and pyrolyzed with three kinds of heating rate,3 900 min,1 500 min and 1 000 min respectively.The distinction of 3D-Cf/SiC samples fabricated at three kinds of heating rate was not obvious.Bending strength of sample at 1 000 min heating rate was 762.5 MPa,and a little better than the others.Three samples at various heating rate had similar micro-graph of fracture surface and fracture toughness.The research results show that mechanics performances of Cf/SiC composites did not decrease when heating rate was properly increased.
基金financial support from the Defence Research and Development Organisation, Ministry of Defence, Govt. of India, New Delhi in order to carry out the present study under project DMR-295
文摘Filler materials of(ZrB_2-SiC-B_4C-YAG) composite were developed for gas tungsten arc welding(GTAW) of the ZrB_2-SiC and Cf-SiC based composites to themselves and to each other. Reaction with filler material,porosity and cracks were not observed at weld interfaces of all the joints. Penetration of filler material in to voids and pores existing in the Cf-SiC composites was observed. Average shear strength of 25.7 MPa was achieved for joints of Cf-SiC composites. By incorporation of Cf-SiC(CVD) ground short fibre reinforcement the(ZrB_2-SiC-B_4C-YAG) composite was machinable with tungsten carbide tool. The joint and machined composites were resistance to oxidation and thermal shock when exposed to the oxy-propane flame at 2300℃ for 300s. The combination of(ZrB_2-SiC-B_4C-YAG) and Cf-SiC based composites can be used for making parts like thermal protection system or nozzles for high temperature applications.
基金Project(50721003) supported by the Innovation Community Foundation of National Natural Science of ChinaProject(2011CB605805) supported by the National Basic Research Program of China
文摘To improve the oxidation resistance of carbon/carbon composites,ZrB2-MoSi2/SiC coating on the carbon/carbon substrate was prepared.The inner coating of SiC was prepared by pack cementation and the outer coating of ZrB2-MoSi2 was prepared by slurry painting.The phase compositions and microstructures of the coating were characterized by XRD and SEM,respectively.The preparation and the high temperature oxidation property of the coated composites were investigated.The results show that the outer coating of carbon/carbon composites is composed of ZrB2,MoSi2 and SiC phases.The mass losses of the ZrB2-MoSi2/SiC coated samples with SiC nano-whiskers after 30 h and 10 h of oxidation at 1 273 K and 1 773 K were,respectively,5.3% and 3.0%.The ZrB2-MoSi2/SiC coated samples exhibit self-sealing performance and good oxidation resistance at high temperature.
基金Projects(51272213,51221001)supported by the National Natural Science Foundation of ChinaProject(73-QP-2010)supported by the Research Fund of the State Key Laboratory of Solidification Processing(NWPU)Project(B08040)supported by Program of Introducing Talents of Discipline to Universities,China
文摘C/SiC/MoSi2-SiC-Si oxidation protective multilayer coating for carbon/carbon （C/C） composites was prepared by pack cementation and slurry method. The microstructure, element distribution and phase composition of the as-received coating were analyzed by scanning electron microscopy （SEM）, energy dispersive X-ray spectroscopy （EDS） and X-ray diffraction （XRD）. The results show that the multilayer coating was composed of MoSi2, SiC and Si. It could effectively protect C/C composites against oxidation for 200 h with the mass loss of 3.25% at 1873 K in static air. The mass loss of the coated C/C composites results from the volatilization of SiO2 and the formation of cracks and bubble holes in the coating.
基金Projects(51221001,51222207)supported by the National Natural Science Foundation of ChinaProject(090677)supported by the Program for New Century Excellent Talents in University of Ministry of Education of ChinaProject(B08040)supported by the Program of Introducing Talents of Discipline to Universities (111 Project) of China
文摘To improve the oxidation resistance of C/C composites, a double SiC protective coating was prepared by a two-step technique. Firstly, the inner SiC layer was prepared by a pack cementation technique, and then an outer uniform and compact SiC coating was obtained by low pressure chemical vapor deposition. The microstructures and phase compositions of the coatings were characterized by SEM, EDS and XRD analyses. Oxidation behaviour of the SiC coated C/C composites was also investigated. It was found that the double SiC coating could protect C/C composites against oxidation at 1773 K in air for 178 h with a mass loss of 1.25%. The coated samples also underwent thermal shocks between 1773 K and room temperature 16 times. The mass loss of the coated C/C composites was only 2.74%. Double SiC layer structures were uniform and dense, and can suppress the generation of thermal stresses, facilitating an excellent anti-oxidation coating.
基金Projects (50872018, 50902018) supported by the National Natural Science Foundation of ChinaProject (1099043) supported by the Science and Technology in Guangxi Province, ChinaProject (090302005) supported by the Basic Research Fund for Northeastern University, China
文摘The mass of high-speed trains can be reduced using the brake disk prepared with SiC network ceramic frame reinforced 6061 aluminum alloy composite （SiCn/Al）. The thermal and stress analyses of SiCn/Al brake disk during emergency braking at a speed of 300 km/h considering airflow cooling were investigated using finite element （FE） and computational fluid dynamics （CFD） methods. All three modes of heat transfer （conduction, convection and radiation） were analyzed along with the design features of the brake assembly and their interfaces. The results suggested that the higher convection coefficients achieved with airflow cooling will not only reduce the maximum temperature in the braking but also reduce the thermal gradients, since heat will be removed faster from hotter parts of the disk. Airflow cooling should be effective to reduce the risk of hot spot formation and disc thermal distortion. The highest temperature after emergency braking was 461 °C and 359 °C without and with considering airflow cooling, respectively. The equivalent stress could reach 269 MPa and 164 MPa without and with considering airflow cooling, respectively. However, the maximum surface stress may exceed the material yield strength during an emergency braking, which may cause a plastic damage accumulation in a brake disk without cooling. The simulation results are consistent with the experimental results well.
