A new method was proposed for preparing AZ31/1060 composite plates with a corrugated interface,which involved cold-pressing a corrugated surface on the Al plate and then hot-pressing the assembled Mg/Al plate.The resu...A new method was proposed for preparing AZ31/1060 composite plates with a corrugated interface,which involved cold-pressing a corrugated surface on the Al plate and then hot-pressing the assembled Mg/Al plate.The results show that cold-pressing produces intense plastic deformation near the corrugated surface of the Al plate,which promotes dynamic recrystallization of the Al substrate near the interface during the subsequent hot-pressing.In addition,the initial corrugation on the surface of the Al plate also changes the local stress state near the interface during hot pressing,which has a large effect on the texture components of the substrates near the corrugated interface.The construction of the corrugated interface can greatly enhance the shear strength by 2−4 times due to the increased contact area and the strong“mechanical gearing”effect.Moreover,the mechanical properties are largely depended on the orientation relationship between corrugated direction and loading direction.展开更多
The lamellar layer of intermetallic compounds(IMCs)was adversely affected the performance of welding-brazing joints in Al/steel dissimilar metals.In this study,a short fiber-like surface morphology was fabricated on t...The lamellar layer of intermetallic compounds(IMCs)was adversely affected the performance of welding-brazing joints in Al/steel dissimilar metals.In this study,a short fiber-like surface morphology was fabricated on the butt surface of Q235 steel via laser.The interaction behavior between the short fibers and the molten pool was captured using a high-speed camera.Laser-arc hybrid welding-brazing was then employed to join Al(6061-T6)to the steel.This process successfully created a short fiber-like interface structure at the joint.The relationship between microstructure and mechanical properties was investigated,compared with Al/bare steel(ABS)joint.The research results indicated that the IMCs layer consisted of FeAl_(3)and Fe_(2)Al_(5).The interface strength of the Al/short fiber-like surface structural steel(ASFSSS)joint reached 153.2 MPa,an 82.2%increase compared to the ABS joint,which reached 84.1 MPa.When the ASFSSS joints without the reinforcement were bent to 58.2°and 25.2°in the longitudinal and transverse direction,respectively,they remained intact.However,cracks were discovered when the bending angle of the ABS reached 39.1°and 0°in the two directions.Numerical simulation revealed that the short fiber-like interface structure significantly reduced residual stress and improved the stress distribution in the weld,thereby enhancing the strength and toughness of Al/steel dissimilar joints.The crack propagation path in the ASFSSS joint was deflected into the weld when it encountered short fibers,and the fracture morphology presented the characteristic of ductile-brittle mixed fracture.展开更多
35% SiCp/2024 Al（volume fraction） composite was prepared by powder metallurgy method. The microstructures of Si Cp/Al interfaces and precipitate phase/Al interfaces were characterized by HRTEM, and the interface con...35% SiCp/2024 Al（volume fraction） composite was prepared by powder metallurgy method. The microstructures of Si Cp/Al interfaces and precipitate phase/Al interfaces were characterized by HRTEM, and the interface conditions were evaluated by tensile modules of elasticity and Brinell hardness measurement. The results show that the overall Si Cp/Al interface condition in this experiment is good and three kinds of Si Cp/Al interfaces are present in the composites, which include vast majority of clean planer interfaces, few slight reaction interfaces and tiny amorphous interfaces. The combination mechanism of Si C and Al in the clean planer interface is the formation of a semi-coherent interface by closely matching of atoms and there are no fixed or preferential crystallographic orientation relationships between Si C and Al. MgAl2O4 spinel particles act as an intermediate to form semi-coherent interface with SiC and Al respectively at the slight reaction interfaces. When the composite is aged at 190 °C for 9 h after being solution-treated at 510 °C for 2 h, numerous discoid-shaped and needle-shaped nanosized precipitates dispersively exist in the composite and are semi-coherent of low mismatch with Al matrix. The Brinell hardness of composites arrives peak value at this time.展开更多
A Fe/Al clad tube was prepared by explosive welding.Then the bonding characteristic of the interface was investigated by compression,flattening and compression-shear test.The test results exhibit that the clad tubes p...A Fe/Al clad tube was prepared by explosive welding.Then the bonding characteristic of the interface was investigated by compression,flattening and compression-shear test.The test results exhibit that the clad tubes possessing good bonding interface have higher shear strength than that of pure aluminum and can bear both axial and radial deformation.The original interface between aluminum layer and ferrite layer was observed by scanning electron microscopy（SEM）.The results show that the clad tubes with good bonding properties possess the interface in wave and straight shape.The Fe/Al clad tube was used to manufacture the T-shape by hydro-bulging.It is found that the good-bonding interface of the Fe/Al clad tube plays a dominant role in the formation of the T-shape.展开更多
A nickel-based coating was deposited on the pure Al substrate by immersion plating,and the Al/Cu bimetals were prepared by diffusion bonding in the temperature range of 450-550 ℃.The interce microstructure and fractu...A nickel-based coating was deposited on the pure Al substrate by immersion plating,and the Al/Cu bimetals were prepared by diffusion bonding in the temperature range of 450-550 ℃.The interce microstructure and fracture surface of Al/Cu joints were studied by scanning electron microscopy（SEM） and X-ray diffraction（XRD）.The mechanical properties of the Al/Cu bimetals were measured by tensile shear and microhardness tests.The results show that the Ni interiayer can effectively eliminate the formation of Al-Cu intermetallic compounds.The Al/Ni interface consists of the Al3Ni and Al3Ni2 phases,while it is Ni-Cu solid solution at the Ni/Cu interce.The tensile shear strength of the joints is improved by the addition of Ni interiayer.The joint with Ni interiayer annealed at 500 ℃ exhibits a maximum value of tensile shear strength of 34.7 MPa.展开更多
The matrix accumulative roll bonding technology （MARB） can improve the matrix performance of metal composite and strengthen the bonding quality of the interface./n this research, for the fwst time, the technology of...The matrix accumulative roll bonding technology （MARB） can improve the matrix performance of metal composite and strengthen the bonding quality of the interface./n this research, for the fwst time, the technology of MARB was proposed. A sound Cu/AI bonding composite was obtained using the MARB process and the bonding characteristic of the interface was studied using scanning electricity microscope （SEM） and energy-dispersive spectroscopy （EDS）. The result indicated that accumulation cycles and diffusion annealing temperature were the most important factors for fabricating a Cu/AI composite material. The substrate aluminum was strengthened by MARB, and a high quality Cu/AI composite with sound interface was obtained as well.展开更多
Cu/Al bar clad material was fabricated by a drawing process and a subsequent heat treatment.During these processes,intermetallic compounds have been formed at the interface of Cu/Al and have affected its bonding prope...Cu/Al bar clad material was fabricated by a drawing process and a subsequent heat treatment.During these processes,intermetallic compounds have been formed at the interface of Cu/Al and have affected its bonding property.Microstructures of Cu/Al interfaces were observed by OM,SEM and EDX Analyser in order to investigate the bonding properties of the material.According to the microstructure a series of diffusion layers were observed at the interface and the thicknesses of diffusion layers have increased with aging time as a result of the diffusion bonding.The interfaces were composed of 3-ply diffusion layers and their compositions were changed with aging time at 400 °C.These compositional compounds were revealed to be η2,(θ+η2),(α+θ) intermetallic phases.It is evident from V-notch impact tests that the growth of the brittle diffusion layers with the increasing aging time directly influenced delamination distance between the Cu sleeve and the Al core.It is suggested that the proper holding time at 400 °C for aging as post heat treatment of a drawn Cu/Al bar clad material would be within 1 h.展开更多
This review summarizes the work carried out in the field of interface study in carbon nanotube reinforced aluminum （CNT/A1） composites. Much research work has been conducted to reveal the evolution of CNT/A1 interfa...This review summarizes the work carried out in the field of interface study in carbon nanotube reinforced aluminum （CNT/A1） composites. Much research work has been conducted to reveal the evolution of CNT/A1 interface in producing the composite with the purpose of achieving uniform distribution of CNTs and tight interfacial bonding. The effect and principles of coating were reviewed along with the illustration of ＂intermetallic interphases＂ design. Different roles of CNT/Al interface in structural and functional application were elucidated, and the future work that needs attention was addressed.展开更多
Cu/Al clad strips are prepared using solid?liquid cast-rolling bonding(SLCRB)technique with a d160mm×150mm twin-roll experimental caster.The extent of interfacial reactions,composition of the reaction products,an...Cu/Al clad strips are prepared using solid?liquid cast-rolling bonding(SLCRB)technique with a d160mm×150mm twin-roll experimental caster.The extent of interfacial reactions,composition of the reaction products,and their micro-morphology evolution in the SLCRB process are investigated with scanning electron microscope(SEM),energy dispersive spectrometer(EDS),and X-ray diffraction(XRD).In the casting pool,initial aluminized coating is first generated on the copper strip surface,with the diffusion layer mainly consisting ofα(Al)+CuAl2and growing at high temperatures,with the maximum thickness of10μm.After sequent rolling below the kiss point,the diffusion layer is broken by severe elongation,which leads to an additional crack bond process with a fresh interface of virgin base metal.The average thickness is reduced from10to5μm.The reaction products,CuAl2,CuAl,and Cu9Al4,are dispersed along the rolling direction.Peeling and bending test results indicate that the fracture occurs in the aluminum substrate,and the morphology is a dimple pattern.No crack or separation is found at the bonding interface after90°-180°bending.The presented method provides an economical way to fabricate Cu/Al clad strip directly.展开更多
The corrugated + flat rolling(CFR) and traditional rolling(TR) methods were used to prepare Mg/Al clad plates using AZ31 B Mg and 5052 Al plates, and the interface morphologies and mechanical properties of the resulti...The corrugated + flat rolling(CFR) and traditional rolling(TR) methods were used to prepare Mg/Al clad plates using AZ31 B Mg and 5052 Al plates, and the interface morphologies and mechanical properties of the resulting clad plates were compared. Examination of the microstructures of the plates showed that the TRed Mg/Al clad plate presented a straight interface, while a corrugated interface containing fractured intermetallic particulates was observed for the CFRed plate due to the inhomogeneous strain induced by the corrugated roller. During the CFR process, the corrugated roller can accelerate the rupture of the substrate work-hardening layers and facilitate the mutual extrusion of fresh metals to enhance the interface bonding. Compared with the traditional basal texture of the Mg alloy, the CFR process can change the texture morphology, thereby enhancing the plastic deformation ability of the Mg plate. Tensile tests showed that the CFRed Mg/Al clad plate exhibited a higher ultimate tensile strength(UTS, 316 MPa), which was~ 8% higher than that of the TRed plate(293 MPa). In addition, the bending curve of the CFRed clad plate was smooth and there was no stress sudden drop phenomenon in the bending process. The higher UTS and excellent bending properties of the CFRed clad plate could be attributed to the enhanced coordinated deformation ability of the substrates induced by the corrugated interface, grain refinement, and the change in the Mg alloy texture morphology.展开更多
The microstructural characteristic of 1070AI matrix composites reinforced by 0.15 祄 AI2O3 particles whose volume fraction was 40% was investigated by TEM and HREM. The results showed that the interface between the ma...The microstructural characteristic of 1070AI matrix composites reinforced by 0.15 祄 AI2O3 particles whose volume fraction was 40% was investigated by TEM and HREM. The results showed that the interface between the matrix and reinforcements was clean and bonded well, without any interfacial reaction products. There were some preferential crystallographic orientation relationships between Al matrix and AI2O3 particle because of the lattice imperfection on the surface of Al2O3 particles.展开更多
The properties of Sc-dopedθ′(Al_(2)Cu)/Al interface in Al−Cu alloys were investigated by first-principles calculations.Sc-doped semi-coherent and coherentθ′(Al_(2)Cu)/Al interfaces(Sc doped in Al slab(S1 site),Sc ...The properties of Sc-dopedθ′(Al_(2)Cu)/Al interface in Al−Cu alloys were investigated by first-principles calculations.Sc-doped semi-coherent and coherentθ′(Al_(2)Cu)/Al interfaces(Sc doped in Al slab(S1 site),Sc doped inθ′slab(S2 site))were modeled based on calculated results and reported experiments.Through the analysis of interfacial bonding strength,it is revealed that the doping of Sc at S1 site can significantly decrease the interface energy and increase the work of adhesion.In particular,the doped coherent interface with Sc at S1 site which is occupied by interstitial Cu atoms has very good bonding strength.The electronic structure shows the strong Al—Cu bonds at the interfaces with Sc at S1 site,and the Al—Al bonds at the interfaces with Sc at S2 site are formed.The formation of strong Al—Cu and Al—Al bonds plays an important role in the enhancement of doped interface strength.展开更多
Fabricating Mg/Al laminate is an effective strategy to circumvent the inherently low formability and poor corrosion resistance of Mg alloys.Here,Mg/Al laminate with good bonding quality and mechanical properties was s...Fabricating Mg/Al laminate is an effective strategy to circumvent the inherently low formability and poor corrosion resistance of Mg alloys.Here,Mg/Al laminate with good bonding quality and mechanical properties was successfully fabricated via porthole die co-extrusion process using ZK60 Mg and TiB_(2)/6061Al composite as constituted layers.Integrating the results from microstructural characterization and mechanical testing,the effects of extrusion temperature on microstructure,interfacial structure,element diffusion,and mechanical properties were investigated.The results show that Mg/Al laminate achieves a sound welding quality by mechanical bonding and diffusion bonding.The obvious intermetallic compounds(βandγ)layer forms at Mg/Al interface,and its thickness increases to 8.3μm as the extrusion temperature reaches 400℃.High extrusion temperature promotes the dynamic recrystallization and grain growth of Mg and Al layers,while the dislocation density decreases.β/γinterface shows a coherent feature,whileγ/Mg interface is semi-coherent with a locally ordered transition zone of 4.5 nm.The rich Mg and Cr layers are found at TiB_(2)/6061 interface,which is conducive to improving the bonding quality.When the extrusion temperature is 370℃,the thickness of diffusion layer is around 5.0μm,and the bonding strength reaches 18.68 MPa,resulting in the best comprehensive mechanical properties.This work provides a new direction for the development of Mg/Al laminate with excellent strength and ductility.展开更多
TiAl is diffusion bonded with Ti, TC4 Alloy and 40Cr Steel by heating in vacuum, and analysis of interfaces shows stratified Ti 3Al forms in TiAl/Ti interface closest to TiAl base, and the α phase and the α+β phase...TiAl is diffusion bonded with Ti, TC4 Alloy and 40Cr Steel by heating in vacuum, and analysis of interfaces shows stratified Ti 3Al forms in TiAl/Ti interface closest to TiAl base, and the α phase and the α+β phase arise closest to Ti base at lower temperature and higher temperature respectively; Structure of TiAl/TC4 interface is TiAl/γ+α 2/Ti 3Al/α-Ti/TC4 at lower temperature and TiAl/γ+β+α 2/TC4 at high temperature; in TiAl/40Cr steel interface, obvious decarbonised layer on steel side while TiC and reaction phase with Fe Al Ti system form on TiAl side.展开更多
Traditional rolled(TR)aluminum(Al)/magnesium(Mg)/aluminum(Al)composite plates have many bottlenecks such as multiple passes,low interlaminar strength,and weak mechanical properties.In this paper,the hard-plate rolling...Traditional rolled(TR)aluminum(Al)/magnesium(Mg)/aluminum(Al)composite plates have many bottlenecks such as multiple passes,low interlaminar strength,and weak mechanical properties.In this paper,the hard-plate rolling(HPR)method was used to prepare Al/Mg/Al composite plates under a single pass reduction of 60%.The results show that the ultimate tensile strength(UTS)of the composite plate obtained by hard-plate rolling is 262.3 MPa,and the percentage of total elongation at fracture(At)is 12.3%,which is 31.6%and 37.4%higher than that of the traditional rolling,respectively.It is attributed to the unique corrugated interlocking structure of the interface of the composite plate caused by hard-plate rolling.The shear texture produced by the Mg plate weakens the strong-basal texture.At the same time,the strong basal slip and the large amount of energy stored in the deformed grains provide favorable conditions for dynamic recrystallized(DRX)nucleation.The microstructure is deeply refined by DRX,and the strength and plasticity of the composite plate are improved synchronously.It provides scientific guidance for the development of high-performance lightweight composite plates and the research on hard-plate rolling technology and also has good industrial production and application potential.展开更多
Thickness of the intermetallic compounds(IMC)layer at the interface has a significant effect on the mechanical properties of Mg/Al dissimilar joints.However,the thickness of IMC layer can be only obtained by metallurg...Thickness of the intermetallic compounds(IMC)layer at the interface has a significant effect on the mechanical properties of Mg/Al dissimilar joints.However,the thickness of IMC layer can be only obtained by metallurgical microscopy,which is destructive and has to break down the weld.Therefore,it is crucial to find a reliable approach that can non-destructively predict the thickness of IMC layer in practical application.In the current study,Mg alloy and Al alloy were friction stir butt welded(FSW)under different tool rotation speeds(TRS)to obtain different thicknesses of IMC layers.As the TRS increased from 400 rpm to 1000 rpm,thickness of the IMC layer increased from 0.4μm to 1.3μm,the peak welding temperatures increased from 259℃to 402℃,and the Z-axis downforces decreased from10.5 kN to 3.2 k N during welding process.Higher TRS would generally induce higher welding heat input,which promotes the growth of the IMC layer and the softening of base materials.The IMC layer formed through solid-state diffusion and transformation instead of eutectic reaction according to the welding temperature history and interfacial microstructure,and its evolution process was clearly observed by plan view.In order to incorporate the effect of dramatic change of welding temperature which is the characteristic feature of FSW,Psd Voigt function was used to fit the welding temperature histories.A new prediction formula was then established to predict thicknesses of IMC layers with considering sharp welding temperature change.Predicted thicknesses gave good agreement with measured thicknesses obtained experimentally under different welding parameters,which confirmed the accuracy and reliability of the new prediction formula.Based on this prediction formula,the time period of temperature higher than 200℃during welding was found critical for the thickening of interfacial IMC layers.展开更多
基金supported by Guangdong Major Project of Basic and Applied Basic Research, China (No. 2020B0301030006)Fundamental Research Funds for the Central Universities, China (No. SWU-XDJH202313)+1 种基金Chongqing Postdoctoral Science Foundation Funded Project, China (No. 2112012728014435)the Chongqing Postgraduate Research and Innovation Project, China (No. CYS23197)。
文摘A new method was proposed for preparing AZ31/1060 composite plates with a corrugated interface,which involved cold-pressing a corrugated surface on the Al plate and then hot-pressing the assembled Mg/Al plate.The results show that cold-pressing produces intense plastic deformation near the corrugated surface of the Al plate,which promotes dynamic recrystallization of the Al substrate near the interface during the subsequent hot-pressing.In addition,the initial corrugation on the surface of the Al plate also changes the local stress state near the interface during hot pressing,which has a large effect on the texture components of the substrates near the corrugated interface.The construction of the corrugated interface can greatly enhance the shear strength by 2−4 times due to the increased contact area and the strong“mechanical gearing”effect.Moreover,the mechanical properties are largely depended on the orientation relationship between corrugated direction and loading direction.
基金supported by the National Natural Science Foundation of China(No.52275306)the Beijing Municipal Natural Science Foundation(No.3232021).
文摘The lamellar layer of intermetallic compounds(IMCs)was adversely affected the performance of welding-brazing joints in Al/steel dissimilar metals.In this study,a short fiber-like surface morphology was fabricated on the butt surface of Q235 steel via laser.The interaction behavior between the short fibers and the molten pool was captured using a high-speed camera.Laser-arc hybrid welding-brazing was then employed to join Al(6061-T6)to the steel.This process successfully created a short fiber-like interface structure at the joint.The relationship between microstructure and mechanical properties was investigated,compared with Al/bare steel(ABS)joint.The research results indicated that the IMCs layer consisted of FeAl_(3)and Fe_(2)Al_(5).The interface strength of the Al/short fiber-like surface structural steel(ASFSSS)joint reached 153.2 MPa,an 82.2%increase compared to the ABS joint,which reached 84.1 MPa.When the ASFSSS joints without the reinforcement were bent to 58.2°and 25.2°in the longitudinal and transverse direction,respectively,they remained intact.However,cracks were discovered when the bending angle of the ABS reached 39.1°and 0°in the two directions.Numerical simulation revealed that the short fiber-like interface structure significantly reduced residual stress and improved the stress distribution in the weld,thereby enhancing the strength and toughness of Al/steel dissimilar joints.The crack propagation path in the ASFSSS joint was deflected into the weld when it encountered short fibers,and the fracture morphology presented the characteristic of ductile-brittle mixed fracture.
基金Project(51371077)supported by the National Natural Science Foundation of China
文摘35% SiCp/2024 Al（volume fraction） composite was prepared by powder metallurgy method. The microstructures of Si Cp/Al interfaces and precipitate phase/Al interfaces were characterized by HRTEM, and the interface conditions were evaluated by tensile modules of elasticity and Brinell hardness measurement. The results show that the overall Si Cp/Al interface condition in this experiment is good and three kinds of Si Cp/Al interfaces are present in the composites, which include vast majority of clean planer interfaces, few slight reaction interfaces and tiny amorphous interfaces. The combination mechanism of Si C and Al in the clean planer interface is the formation of a semi-coherent interface by closely matching of atoms and there are no fixed or preferential crystallographic orientation relationships between Si C and Al. MgAl2O4 spinel particles act as an intermediate to form semi-coherent interface with SiC and Al respectively at the slight reaction interfaces. When the composite is aged at 190 °C for 9 h after being solution-treated at 510 °C for 2 h, numerous discoid-shaped and needle-shaped nanosized precipitates dispersively exist in the composite and are semi-coherent of low mismatch with Al matrix. The Brinell hardness of composites arrives peak value at this time.
基金Project(BA2006067)supported by Achievement Transitional Foundation of Jiangsu Province,China
文摘A Fe/Al clad tube was prepared by explosive welding.Then the bonding characteristic of the interface was investigated by compression,flattening and compression-shear test.The test results exhibit that the clad tubes possessing good bonding interface have higher shear strength than that of pure aluminum and can bear both axial and radial deformation.The original interface between aluminum layer and ferrite layer was observed by scanning electron microscopy（SEM）.The results show that the clad tubes with good bonding properties possess the interface in wave and straight shape.The Fe/Al clad tube was used to manufacture the T-shape by hydro-bulging.It is found that the good-bonding interface of the Fe/Al clad tube plays a dominant role in the formation of the T-shape.
基金Projects (51274054,51375070,51271042) supported by the National Natural Science Foundation of ChinaProjects (2013M530913) supported by the China Postdoctoral Science Foundation
文摘A nickel-based coating was deposited on the pure Al substrate by immersion plating,and the Al/Cu bimetals were prepared by diffusion bonding in the temperature range of 450-550 ℃.The interce microstructure and fracture surface of Al/Cu joints were studied by scanning electron microscopy（SEM） and X-ray diffraction（XRD）.The mechanical properties of the Al/Cu bimetals were measured by tensile shear and microhardness tests.The results show that the Ni interiayer can effectively eliminate the formation of Al-Cu intermetallic compounds.The Al/Ni interface consists of the Al3Ni and Al3Ni2 phases,while it is Ni-Cu solid solution at the Ni/Cu interce.The tensile shear strength of the joints is improved by the addition of Ni interiayer.The joint with Ni interiayer annealed at 500 ℃ exhibits a maximum value of tensile shear strength of 34.7 MPa.
基金the National Natural Science Foundation of China (No. 50375019).
文摘The matrix accumulative roll bonding technology （MARB） can improve the matrix performance of metal composite and strengthen the bonding quality of the interface./n this research, for the fwst time, the technology of MARB was proposed. A sound Cu/AI bonding composite was obtained using the MARB process and the bonding characteristic of the interface was studied using scanning electricity microscope （SEM） and energy-dispersive spectroscopy （EDS）. The result indicated that accumulation cycles and diffusion annealing temperature were the most important factors for fabricating a Cu/AI composite material. The substrate aluminum was strengthened by MARB, and a high quality Cu/AI composite with sound interface was obtained as well.
基金Project supported by the Fundamental Materials Development funded by the Korean Ministry of Knowledge Economy
文摘Cu/Al bar clad material was fabricated by a drawing process and a subsequent heat treatment.During these processes,intermetallic compounds have been formed at the interface of Cu/Al and have affected its bonding property.Microstructures of Cu/Al interfaces were observed by OM,SEM and EDX Analyser in order to investigate the bonding properties of the material.According to the microstructure a series of diffusion layers were observed at the interface and the thicknesses of diffusion layers have increased with aging time as a result of the diffusion bonding.The interfaces were composed of 3-ply diffusion layers and their compositions were changed with aging time at 400 °C.These compositional compounds were revealed to be η2,(θ+η2),(α+θ) intermetallic phases.It is evident from V-notch impact tests that the growth of the brittle diffusion layers with the increasing aging time directly influenced delamination distance between the Cu sleeve and the Al core.It is suggested that the proper holding time at 400 °C for aging as post heat treatment of a drawn Cu/Al bar clad material would be within 1 h.
基金financially supported by the National Basic Research Program of China (No.2012CB619600)the National Natural Science Foundation of China (Nos.51131004,51071100,and 51001071)+1 种基金the National High Technology Research and Development Program of China (No.2012AA030311)Shanghai Science & Technology Committee (Nos.11JC1405500)
文摘This review summarizes the work carried out in the field of interface study in carbon nanotube reinforced aluminum （CNT/A1） composites. Much research work has been conducted to reveal the evolution of CNT/A1 interface in producing the composite with the purpose of achieving uniform distribution of CNTs and tight interfacial bonding. The effect and principles of coating were reviewed along with the illustration of ＂intermetallic interphases＂ design. Different roles of CNT/Al interface in structural and functional application were elucidated, and the future work that needs attention was addressed.
基金Project(51474189)supported by the National Natural Science Foundation of ChinaProject(QN2015214)supported by the Educational Commission of Hebei Province,China
文摘Cu/Al clad strips are prepared using solid?liquid cast-rolling bonding(SLCRB)technique with a d160mm×150mm twin-roll experimental caster.The extent of interfacial reactions,composition of the reaction products,and their micro-morphology evolution in the SLCRB process are investigated with scanning electron microscope(SEM),energy dispersive spectrometer(EDS),and X-ray diffraction(XRD).In the casting pool,initial aluminized coating is first generated on the copper strip surface,with the diffusion layer mainly consisting ofα(Al)+CuAl2and growing at high temperatures,with the maximum thickness of10μm.After sequent rolling below the kiss point,the diffusion layer is broken by severe elongation,which leads to an additional crack bond process with a fresh interface of virgin base metal.The average thickness is reduced from10to5μm.The reaction products,CuAl2,CuAl,and Cu9Al4,are dispersed along the rolling direction.Peeling and bending test results indicate that the fracture occurs in the aluminum substrate,and the morphology is a dimple pattern.No crack or separation is found at the bonding interface after90°-180°bending.The presented method provides an economical way to fabricate Cu/Al clad strip directly.
基金financially supported by the National Natural Science Foundation of China(Nos.U1710254,51904205,51904206)Science and Technology Foundation of State Key laboratory(No.6142909180205)+4 种基金Taiyuan City Science and Technology Major Projects(No.170203)Shanxi Province Science and Technology Major Projects(Nos.MC2016-01,20181101008)the Natural Science Foundation of Shanxi Province(Nos.201801D221221,201801D221130 and 201801D221346)Key Projects of Shanxi Province Key Research and Development Plan(No.201703D111003)the China Postdoctoral Science Foundation(Nos.2018M641680,2018M641681)。
文摘The corrugated + flat rolling(CFR) and traditional rolling(TR) methods were used to prepare Mg/Al clad plates using AZ31 B Mg and 5052 Al plates, and the interface morphologies and mechanical properties of the resulting clad plates were compared. Examination of the microstructures of the plates showed that the TRed Mg/Al clad plate presented a straight interface, while a corrugated interface containing fractured intermetallic particulates was observed for the CFRed plate due to the inhomogeneous strain induced by the corrugated roller. During the CFR process, the corrugated roller can accelerate the rupture of the substrate work-hardening layers and facilitate the mutual extrusion of fresh metals to enhance the interface bonding. Compared with the traditional basal texture of the Mg alloy, the CFR process can change the texture morphology, thereby enhancing the plastic deformation ability of the Mg plate. Tensile tests showed that the CFRed Mg/Al clad plate exhibited a higher ultimate tensile strength(UTS, 316 MPa), which was~ 8% higher than that of the TRed plate(293 MPa). In addition, the bending curve of the CFRed clad plate was smooth and there was no stress sudden drop phenomenon in the bending process. The higher UTS and excellent bending properties of the CFRed clad plate could be attributed to the enhanced coordinated deformation ability of the substrates induced by the corrugated interface, grain refinement, and the change in the Mg alloy texture morphology.
基金This research is supported by the National Natural Science Foundation of China (under Grant No.59771014 and No.50071019). The help of the National Advanced Material Open Research Lab of Tsinghua University is gratefully acknowledged.
文摘The microstructural characteristic of 1070AI matrix composites reinforced by 0.15 祄 AI2O3 particles whose volume fraction was 40% was investigated by TEM and HREM. The results showed that the interface between the matrix and reinforcements was clean and bonded well, without any interfacial reaction products. There were some preferential crystallographic orientation relationships between Al matrix and AI2O3 particle because of the lattice imperfection on the surface of Al2O3 particles.
基金the financia supports from the National Key Research and Development Program of China (No. 2019YFB2006500)the National Natura Science Foundation of China (Nos. 52171024 51771234, 51601228)。
文摘The properties of Sc-dopedθ′(Al_(2)Cu)/Al interface in Al−Cu alloys were investigated by first-principles calculations.Sc-doped semi-coherent and coherentθ′(Al_(2)Cu)/Al interfaces(Sc doped in Al slab(S1 site),Sc doped inθ′slab(S2 site))were modeled based on calculated results and reported experiments.Through the analysis of interfacial bonding strength,it is revealed that the doping of Sc at S1 site can significantly decrease the interface energy and increase the work of adhesion.In particular,the doped coherent interface with Sc at S1 site which is occupied by interstitial Cu atoms has very good bonding strength.The electronic structure shows the strong Al—Cu bonds at the interfaces with Sc at S1 site,and the Al—Al bonds at the interfaces with Sc at S2 site are formed.The formation of strong Al—Cu and Al—Al bonds plays an important role in the enhancement of doped interface strength.
基金supports from the National Natural Science Foundation of China(52175338 and 52222510)Science Fund for Distinguished Young Scholars of Shandong Province(ZR2021JQ21)Key Research and Development Program of Shandong Province(2021ZLGX01).
文摘Fabricating Mg/Al laminate is an effective strategy to circumvent the inherently low formability and poor corrosion resistance of Mg alloys.Here,Mg/Al laminate with good bonding quality and mechanical properties was successfully fabricated via porthole die co-extrusion process using ZK60 Mg and TiB_(2)/6061Al composite as constituted layers.Integrating the results from microstructural characterization and mechanical testing,the effects of extrusion temperature on microstructure,interfacial structure,element diffusion,and mechanical properties were investigated.The results show that Mg/Al laminate achieves a sound welding quality by mechanical bonding and diffusion bonding.The obvious intermetallic compounds(βandγ)layer forms at Mg/Al interface,and its thickness increases to 8.3μm as the extrusion temperature reaches 400℃.High extrusion temperature promotes the dynamic recrystallization and grain growth of Mg and Al layers,while the dislocation density decreases.β/γinterface shows a coherent feature,whileγ/Mg interface is semi-coherent with a locally ordered transition zone of 4.5 nm.The rich Mg and Cr layers are found at TiB_(2)/6061 interface,which is conducive to improving the bonding quality.When the extrusion temperature is 370℃,the thickness of diffusion layer is around 5.0μm,and the bonding strength reaches 18.68 MPa,resulting in the best comprehensive mechanical properties.This work provides a new direction for the development of Mg/Al laminate with excellent strength and ductility.
文摘TiAl is diffusion bonded with Ti, TC4 Alloy and 40Cr Steel by heating in vacuum, and analysis of interfaces shows stratified Ti 3Al forms in TiAl/Ti interface closest to TiAl base, and the α phase and the α+β phase arise closest to Ti base at lower temperature and higher temperature respectively; Structure of TiAl/TC4 interface is TiAl/γ+α 2/Ti 3Al/α-Ti/TC4 at lower temperature and TiAl/γ+β+α 2/TC4 at high temperature; in TiAl/40Cr steel interface, obvious decarbonised layer on steel side while TiC and reaction phase with Fe Al Ti system form on TiAl side.
基金supported by the Key Laboratory of Micro-systems and Micro-structures Manufacturing of Ministry of Education,Harbin Institute of Technology(2020KM005).
文摘Traditional rolled(TR)aluminum(Al)/magnesium(Mg)/aluminum(Al)composite plates have many bottlenecks such as multiple passes,low interlaminar strength,and weak mechanical properties.In this paper,the hard-plate rolling(HPR)method was used to prepare Al/Mg/Al composite plates under a single pass reduction of 60%.The results show that the ultimate tensile strength(UTS)of the composite plate obtained by hard-plate rolling is 262.3 MPa,and the percentage of total elongation at fracture(At)is 12.3%,which is 31.6%and 37.4%higher than that of the traditional rolling,respectively.It is attributed to the unique corrugated interlocking structure of the interface of the composite plate caused by hard-plate rolling.The shear texture produced by the Mg plate weakens the strong-basal texture.At the same time,the strong basal slip and the large amount of energy stored in the deformed grains provide favorable conditions for dynamic recrystallized(DRX)nucleation.The microstructure is deeply refined by DRX,and the strength and plasticity of the composite plate are improved synchronously.It provides scientific guidance for the development of high-performance lightweight composite plates and the research on hard-plate rolling technology and also has good industrial production and application potential.
基金supported by the National Natural Science Foundation of China(No.52075330)the Interdisciplinary Program of Shanghai Jiao Tong University(No.YG2019QNA15)the Foundation of National Facility for Translational Medicine(Shanghai)(No.TMSK-2020-107)。
文摘Thickness of the intermetallic compounds(IMC)layer at the interface has a significant effect on the mechanical properties of Mg/Al dissimilar joints.However,the thickness of IMC layer can be only obtained by metallurgical microscopy,which is destructive and has to break down the weld.Therefore,it is crucial to find a reliable approach that can non-destructively predict the thickness of IMC layer in practical application.In the current study,Mg alloy and Al alloy were friction stir butt welded(FSW)under different tool rotation speeds(TRS)to obtain different thicknesses of IMC layers.As the TRS increased from 400 rpm to 1000 rpm,thickness of the IMC layer increased from 0.4μm to 1.3μm,the peak welding temperatures increased from 259℃to 402℃,and the Z-axis downforces decreased from10.5 kN to 3.2 k N during welding process.Higher TRS would generally induce higher welding heat input,which promotes the growth of the IMC layer and the softening of base materials.The IMC layer formed through solid-state diffusion and transformation instead of eutectic reaction according to the welding temperature history and interfacial microstructure,and its evolution process was clearly observed by plan view.In order to incorporate the effect of dramatic change of welding temperature which is the characteristic feature of FSW,Psd Voigt function was used to fit the welding temperature histories.A new prediction formula was then established to predict thicknesses of IMC layers with considering sharp welding temperature change.Predicted thicknesses gave good agreement with measured thicknesses obtained experimentally under different welding parameters,which confirmed the accuracy and reliability of the new prediction formula.Based on this prediction formula,the time period of temperature higher than 200℃during welding was found critical for the thickening of interfacial IMC layers.
