The Al_2O_3-（W,Ti）C composites with Ni and Mo additions varying from 0vol% to 12vol% were prepared via hot pressing sintering under 30 MPa. The microstructure was investigated via X-ray diffraction（XRD） and scanni...The Al_2O_3-（W,Ti）C composites with Ni and Mo additions varying from 0vol% to 12vol% were prepared via hot pressing sintering under 30 MPa. The microstructure was investigated via X-ray diffraction（XRD） and scanning electron microscopy（SEM） equipped with energy dispersive spectrometry（EDS）. Mechanical properties such as flexural strength, fracture toughness, and Vickers hardness were also measured. Results show that the main phases A12O3 and（W,Ti）C were detected by XRD. Compound Mo Ni also existed in sintered nanocomposites. The fracture modes of the nanocomposites were both intergranular and transgranular fractures. The plastic deformation of metal particles and crack bridging were the main toughening mechanisms. The maximum flexural strength and fracture toughness were obtained for 9vol% and 12vol% additions of Ni and Mo, respectively. The hardness of the composites reduced gradually with increasing content of metals Ni and Mo.展开更多
Ceramic materials were investigated as thermal barrier coatings and electrolytes. Electrophoretic deposition（EPD） and physical vapor deposition（PVD） were employed to fabricate samples, and the mechanical propertie...Ceramic materials were investigated as thermal barrier coatings and electrolytes. Electrophoretic deposition（EPD） and physical vapor deposition（PVD） were employed to fabricate samples, and the mechanical properties and microstructure were examined by nanoindentation and microscopy, respectively. Yttria-stabilized zirconia/alumina（YSZ/Al2O3） composite coatings, a candidate for thermal barrier coatings, yield a kinky, rather than smooth, load–displacement curve. Scanning electron microscope（SEM） examination reveals that the kinky curve is because of the porous microstructure and cracks are caused by the compression of the indenter. Li0.34La0.51 Ti O2.94（LLTO） on Si/Sr Ru O3（Si/SRO） substrates, an ionic conductor in nature, demonstrates electronic performance. Although SEM images show a continuous and smooth microstructure, a close examination of the microstructure by transmission electron microscopy（TEM） reveals that the observed spikes indicate electronic performance. Therefore, we can conclude that ceramic coatings could serve multiple purposes but their properties are microstructure-dependent.展开更多
ZrC coatings were deposited on graphite substrates by low pressure chemical vapor deposition（LPCVD） with the Br2-Zr-C3H6-H2-Ar system. The effects of deposition time on the microstructures and growth behavior of ZrC...ZrC coatings were deposited on graphite substrates by low pressure chemical vapor deposition（LPCVD） with the Br2-Zr-C3H6-H2-Ar system. The effects of deposition time on the microstructures and growth behavior of ZrC coatings were investigated. ZrC coating grew in an island-layer mode. The formation of coating was dominated by the nucleation of ZrC in the initial 20 minutes, and the rapid nucleation generated a fine-grained structure of ZrC coating. When the deposition time was over 30 min, the growth of coating was dominated by that of crystals, giving a column-arranged structure. Energy dispersive X-ray spectroscopy showed that the molar ratio of carbon to zirconium was near 1：1 in ZrC coating, and X-ray photoelectron spectroscopy showed that ZrC was the main phase in coatings, accompanied by about 2.5mol% ZrO2 minor phase.展开更多
SiO2–BN ceramic and Ti plate were joined by active brazing in vacuum with Ag–Cu–Ti＋BN composite filler.The effect of BN content,brazing temperature and time on the microstructure and mechanical properties of the b...SiO2–BN ceramic and Ti plate were joined by active brazing in vacuum with Ag–Cu–Ti＋BN composite filler.The effect of BN content,brazing temperature and time on the microstructure and mechanical properties of the brazed joints was investigated.The results showed that a continuous Ti N–Ti B2reaction layer formed adjacent to the SiO2–BN ceramic,whose thickness played a key role in the bonding properties.Four Ti–Cu compound layers,Ti2Cu,Ti3Cu4,Ti Cu2and Ti Cu4,were observed to border Ti substrate due to the strong affinity of Ti and Cu compared with Ag.The central part of the joint was composed of Ag matrix,over which some fine-grains distributed.The added BN particles reacted with Ti in the liquid filler to form fine Ti B whiskers and Ti N particles with low coefficients of thermal expansion（CTE）,leading to the reduction of detrimental residual stress in the joint,and thus improving the joint strength.The maximum shear strength of 31 MPa was obtained when 3 wt%BN was added in the composite filler,which was 158%higher than that brazed with single Ag–Cu–Ti filler metal.The morphology and thickness of the reaction layer adjacent to the parent materials changed correspondingly with the increase of BN content,brazing temperature and holding time.Based on the correlation between the microstructural evolution and brazing parameters,the bonding mechanism of SiO2–BN and Ti was discussed.展开更多
Hexagonal boron nitride ceramic（h-BN） based on the nitridation of B powders was obtained by reaction sintering method. The effects of sintering temperature on the mechanical properties and microstructure of the resu...Hexagonal boron nitride ceramic（h-BN） based on the nitridation of B powders was obtained by reaction sintering method. The effects of sintering temperature on the mechanical properties and microstructure of the resultant products were investigated and the reaction mechanism was discussed. Results showed that the reaction between B and N2 occurred vigorously at temperatures ranging from 1 000 ℃ to 1 300 ℃, which resulted in the generation of t-BN. When the temperature exceeded 1 450 ℃, transformation from t-BN to h-BN began to occur. As the sintering temperature increased, the spherical particles of t-BN gradually transformed into fine sheet particles of h-BN. These particles subsequently displayed a compact arrangement to achieve a more uniform microstructure, thereby increasing the strength.展开更多
Fine powders of γ-Fe_2O_3,doped with Y_2O_3,CeO_2,Eu_2O_3 or Tb_2O_3 have been prepared by the chemical co-precipitation method.The sensitivity of gas sensation has been measured with respect to the relative resist- ...Fine powders of γ-Fe_2O_3,doped with Y_2O_3,CeO_2,Eu_2O_3 or Tb_2O_3 have been prepared by the chemical co-precipitation method.The sensitivity of gas sensation has been measured with respect to the relative resist- ance change in the ceramic matrix upon introduction of inflammable gases.The structure of the materials has been studied with X-ray diffraction spectroscopy(XRD),electron diffraction spectroscopy( ED) and transmis- sion electron microscopy(TEM).The addition of rare earth oxides,which improves ceramic microstructure of γ-Fe_2O_3,improves gas sensitivity of γ-Fe_2O_3.The stability can be increased because of the increase of phase transition temperature.In addition,the selectivity of gas sensation of γ-Fe_2O_3 can be improved because of the variation of rare earth oxides.展开更多
基金financially supported by the National Natural Science Foundation of China (No. 51475273)
文摘The Al_2O_3-（W,Ti）C composites with Ni and Mo additions varying from 0vol% to 12vol% were prepared via hot pressing sintering under 30 MPa. The microstructure was investigated via X-ray diffraction（XRD） and scanning electron microscopy（SEM） equipped with energy dispersive spectrometry（EDS）. Mechanical properties such as flexural strength, fracture toughness, and Vickers hardness were also measured. Results show that the main phases A12O3 and（W,Ti）C were detected by XRD. Compound Mo Ni also existed in sintered nanocomposites. The fracture modes of the nanocomposites were both intergranular and transgranular fractures. The plastic deformation of metal particles and crack bridging were the main toughening mechanisms. The maximum flexural strength and fracture toughness were obtained for 9vol% and 12vol% additions of Ni and Mo, respectively. The hardness of the composites reduced gradually with increasing content of metals Ni and Mo.
基金financially supported by the Natural Science Foundation of Hebei Province,China(No.E2013502272)
文摘Ceramic materials were investigated as thermal barrier coatings and electrolytes. Electrophoretic deposition（EPD） and physical vapor deposition（PVD） were employed to fabricate samples, and the mechanical properties and microstructure were examined by nanoindentation and microscopy, respectively. Yttria-stabilized zirconia/alumina（YSZ/Al2O3） composite coatings, a candidate for thermal barrier coatings, yield a kinky, rather than smooth, load–displacement curve. Scanning electron microscope（SEM） examination reveals that the kinky curve is because of the porous microstructure and cracks are caused by the compression of the indenter. Li0.34La0.51 Ti O2.94（LLTO） on Si/Sr Ru O3（Si/SRO） substrates, an ionic conductor in nature, demonstrates electronic performance. Although SEM images show a continuous and smooth microstructure, a close examination of the microstructure by transmission electron microscopy（TEM） reveals that the observed spikes indicate electronic performance. Therefore, we can conclude that ceramic coatings could serve multiple purposes but their properties are microstructure-dependent.
基金Founded by the National Natural Science Foundation of China(No.91216302)the National Program on Key Basic Research Project of the People's Republic of China(No.2015CB655200)
文摘ZrC coatings were deposited on graphite substrates by low pressure chemical vapor deposition（LPCVD） with the Br2-Zr-C3H6-H2-Ar system. The effects of deposition time on the microstructures and growth behavior of ZrC coatings were investigated. ZrC coating grew in an island-layer mode. The formation of coating was dominated by the nucleation of ZrC in the initial 20 minutes, and the rapid nucleation generated a fine-grained structure of ZrC coating. When the deposition time was over 30 min, the growth of coating was dominated by that of crystals, giving a column-arranged structure. Energy dispersive X-ray spectroscopy showed that the molar ratio of carbon to zirconium was near 1：1 in ZrC coating, and X-ray photoelectron spectroscopy showed that ZrC was the main phase in coatings, accompanied by about 2.5mol% ZrO2 minor phase.
基金supported by the National Natural Science Foundation of China (No. 51405332)
文摘SiO2–BN ceramic and Ti plate were joined by active brazing in vacuum with Ag–Cu–Ti＋BN composite filler.The effect of BN content,brazing temperature and time on the microstructure and mechanical properties of the brazed joints was investigated.The results showed that a continuous Ti N–Ti B2reaction layer formed adjacent to the SiO2–BN ceramic,whose thickness played a key role in the bonding properties.Four Ti–Cu compound layers,Ti2Cu,Ti3Cu4,Ti Cu2and Ti Cu4,were observed to border Ti substrate due to the strong affinity of Ti and Cu compared with Ag.The central part of the joint was composed of Ag matrix,over which some fine-grains distributed.The added BN particles reacted with Ti in the liquid filler to form fine Ti B whiskers and Ti N particles with low coefficients of thermal expansion（CTE）,leading to the reduction of detrimental residual stress in the joint,and thus improving the joint strength.The maximum shear strength of 31 MPa was obtained when 3 wt%BN was added in the composite filler,which was 158%higher than that brazed with single Ag–Cu–Ti filler metal.The morphology and thickness of the reaction layer adjacent to the parent materials changed correspondingly with the increase of BN content,brazing temperature and holding time.Based on the correlation between the microstructural evolution and brazing parameters,the bonding mechanism of SiO2–BN and Ti was discussed.
基金Funded by the Scientific and Technological Development Project of Yantai(2013JH020)
文摘Hexagonal boron nitride ceramic（h-BN） based on the nitridation of B powders was obtained by reaction sintering method. The effects of sintering temperature on the mechanical properties and microstructure of the resultant products were investigated and the reaction mechanism was discussed. Results showed that the reaction between B and N2 occurred vigorously at temperatures ranging from 1 000 ℃ to 1 300 ℃, which resulted in the generation of t-BN. When the temperature exceeded 1 450 ℃, transformation from t-BN to h-BN began to occur. As the sintering temperature increased, the spherical particles of t-BN gradually transformed into fine sheet particles of h-BN. These particles subsequently displayed a compact arrangement to achieve a more uniform microstructure, thereby increasing the strength.
基金The project supported by the National Natural Science Foundation of China
文摘Fine powders of γ-Fe_2O_3,doped with Y_2O_3,CeO_2,Eu_2O_3 or Tb_2O_3 have been prepared by the chemical co-precipitation method.The sensitivity of gas sensation has been measured with respect to the relative resist- ance change in the ceramic matrix upon introduction of inflammable gases.The structure of the materials has been studied with X-ray diffraction spectroscopy(XRD),electron diffraction spectroscopy( ED) and transmis- sion electron microscopy(TEM).The addition of rare earth oxides,which improves ceramic microstructure of γ-Fe_2O_3,improves gas sensitivity of γ-Fe_2O_3.The stability can be increased because of the increase of phase transition temperature.In addition,the selectivity of gas sensation of γ-Fe_2O_3 can be improved because of the variation of rare earth oxides.
