采用共沉淀-高温固相法合成正极材料LiNi0．7 Mn0．3 O 2,利用 X 射线衍射分析（XRD）表征其结构、扫描电子显微镜（SEM）表征其形貌、X 射线光电子能谱（XPS）表征其价态,最终确定了该材料最佳烧成温度为820℃.研究表明,该温度下合成的...采用共沉淀-高温固相法合成正极材料LiNi0．7 Mn0．3 O 2,利用 X 射线衍射分析（XRD）表征其结构、扫描电子显微镜（SEM）表征其形貌、X 射线光电子能谱（XPS）表征其价态,最终确定了该材料最佳烧成温度为820℃.研究表明,该温度下合成的 LiNi0．7 Mn0．3 O 2具有典型的α-NaFeO 2型层状结构,颗粒形貌呈类球形且分布均匀；XPS 数据表明,LiNi0．7 Mn0．3 O 2中的 Ni 主要以＋3价形态存在,Mn 主要以＋4价形态存在.室温条件下以0．2 C 倍率在2．75~4．35 V 的电压范围内充放电,首次放电比容量高达188．9 mAh/g,70次循环后容量保持率为95．2％.展开更多
Ce0.65Zr0.35O2 solid solution was prepared by co-precipitation method and characterized by X-ray diffraction (XRD), Raman spectra, BET, oxygen storage capacity (OSC) and temperature-programmed reduction measurements (...Ce0.65Zr0.35O2 solid solution was prepared by co-precipitation method and characterized by X-ray diffraction (XRD), Raman spectra, BET, oxygen storage capacity (OSC) and temperature-programmed reduction measurements (H2-TPR) after calcination at 100 ℃, 300 ℃, 600 ℃, and 1 000 ℃. The results showed that the precipitation was a crystalline of fluorite structure, and in the process of the precipitation transformation into Ce0.65Zr0.35O2 solid solution, the fluorite structure of the precipitation kept unchanged. The samples had different BET surface areas and OSC at different temperatures, but they held the performance of stable structure. After 1 000 ℃, there didn′t appear the other crystalline phase. So the samples prepared by co-precipitation method had excellent texture and higher thermal stability.展开更多
NiO-La0.3Ce0.7O2-δ(LDC30) novel anode was investigated for IT-SOFCs(Intermediate Temperature-Solid Oxide Fuel Cells) with LaGaO3-based electrolyte. The results showed that LDC30 has a suitable chemical compatibility ...NiO-La0.3Ce0.7O2-δ(LDC30) novel anode was investigated for IT-SOFCs(Intermediate Temperature-Solid Oxide Fuel Cells) with LaGaO3-based electrolyte. The results showed that LDC30 has a suitable chemical compatibility with NiO and NiO-LDC30 has a good thermal expansion matching with LDC30 interlayer and LSGM(La0.8Sr0.2Ga0.8Mg0.2O3-δ) electrolyte, so NiO-LDC30/LDC30 was considered as a feasible and novel anode system. It was also shown that NiO content plays a key role on polarization performance and morphology of the anode. When the content of NiO was 60%(mass fraction), the polarization loss of anode was the lowest. Next we will optimize the porosity and sintering procedure to modify the microstructure and performance of the anode.展开更多
文摘采用共沉淀-高温固相法合成正极材料LiNi0．7 Mn0．3 O 2,利用 X 射线衍射分析（XRD）表征其结构、扫描电子显微镜（SEM）表征其形貌、X 射线光电子能谱（XPS）表征其价态,最终确定了该材料最佳烧成温度为820℃.研究表明,该温度下合成的 LiNi0．7 Mn0．3 O 2具有典型的α-NaFeO 2型层状结构,颗粒形貌呈类球形且分布均匀；XPS 数据表明,LiNi0．7 Mn0．3 O 2中的 Ni 主要以＋3价形态存在,Mn 主要以＋4价形态存在.室温条件下以0．2 C 倍率在2．75~4．35 V 的电压范围内充放电,首次放电比容量高达188．9 mAh/g,70次循环后容量保持率为95．2％.
文摘Ce0.65Zr0.35O2 solid solution was prepared by co-precipitation method and characterized by X-ray diffraction (XRD), Raman spectra, BET, oxygen storage capacity (OSC) and temperature-programmed reduction measurements (H2-TPR) after calcination at 100 ℃, 300 ℃, 600 ℃, and 1 000 ℃. The results showed that the precipitation was a crystalline of fluorite structure, and in the process of the precipitation transformation into Ce0.65Zr0.35O2 solid solution, the fluorite structure of the precipitation kept unchanged. The samples had different BET surface areas and OSC at different temperatures, but they held the performance of stable structure. After 1 000 ℃, there didn′t appear the other crystalline phase. So the samples prepared by co-precipitation method had excellent texture and higher thermal stability.
文摘NiO-La0.3Ce0.7O2-δ(LDC30) novel anode was investigated for IT-SOFCs(Intermediate Temperature-Solid Oxide Fuel Cells) with LaGaO3-based electrolyte. The results showed that LDC30 has a suitable chemical compatibility with NiO and NiO-LDC30 has a good thermal expansion matching with LDC30 interlayer and LSGM(La0.8Sr0.2Ga0.8Mg0.2O3-δ) electrolyte, so NiO-LDC30/LDC30 was considered as a feasible and novel anode system. It was also shown that NiO content plays a key role on polarization performance and morphology of the anode. When the content of NiO was 60%(mass fraction), the polarization loss of anode was the lowest. Next we will optimize the porosity and sintering procedure to modify the microstructure and performance of the anode.
