Deep levels in Cds/CdTe thin film solar cells have a potent influence on the electrical property of these devices. As an essential layer in the solar cell device structure, back contact is believed to induce some deep...Deep levels in Cds/CdTe thin film solar cells have a potent influence on the electrical property of these devices. As an essential layer in the solar cell device structure, back contact is believed to induce some deep defects in the CdTe thin film. With the help of deep level transient spectroscopy （DLTS）, we study the deep levels in CdS/CdTe thin film solar cells with Te：Cu back contact. One hole trap and one electron trap are observed. The hole trap H1, localized at Ev＋0.128~eV, originates from the vacancy of Cd （VCd. The electron trap E1, found at Ec-0.178~eV, is considered to be correlated with the interstitial Cui= in CdTe.展开更多
One of the most promising solar cell devices is cadmium telluride (CdTe) based. These cells however, have their own problems of stability and degradation in efficiency. Measurements show that CdS/CdTe solar cell has h...One of the most promising solar cell devices is cadmium telluride (CdTe) based. These cells however, have their own problems of stability and degradation in efficiency. Measurements show that CdS/CdTe solar cell has high series resistance which degrades the performance of solar cell energy conversion. Both active layers (CdS and CdTe) had been fabricated by thermal evaporation and tested individually. It was found that CdS window layer of 300 nm have the lowest series resistance with maximum light absorption. While 5 - 7 μm CdTe absorber layer absorbed more than 90% of the incident light with minimum series resistance. A complete CdS/CdTe solar cell was fabricated and tested. It was found that deposited cell without heat treatment shows that the short circuit current increment decreases as the light intensity increases. This type of deposited cell has low conversion efficiency. The energy conversion efficiency was improved by heat treatment, depositing heavily doped layer at the back of the cell and minimizing the contact resistivity by depositing material with resistivity less than 1 m??cm2. All these modifications were not enough because the back contact is non-ohmic. Tunnel diode of CdTe (p++)/CdS (n++) was deposited in the back of the cell. The energy conversion efficiency was improved by more than 7%.展开更多
In this paper, interface engineering via sputtering of CdO nanolayer at the buffer-CdS/CdTe-absorber interface is demonstrated as an efficient approach to improve the performance of solar cell device. The i-CdO interf...In this paper, interface engineering via sputtering of CdO nanolayer at the buffer-CdS/CdTe-absorber interface is demonstrated as an efficient approach to improve the performance of solar cell device. The i-CdO interfacial layer with various thicknesses from 5 nm to 35 nm was deposited by DC magnetron sputtering. Comparative studies on TCO/CdS/CdTe and TCO/CdS/CdO/CdTe interfaces have been conducted by current-voltage, capacitance-voltage and admittance spectroscopy measurements. The current-voltage characteristics of the devices with an area of 0.45 cm<sup>2</sup> under 100 mW/cm<sup>2</sup> illumination, at the optimum thickness of CdO intermediate layer in the proposed structures, show increases of the short circuit current density and the open circuit voltage by 5% and 25%, respectively. The efficiency improvement of 3.1% of p-i-n cell over p-n cell is observed. Results of the temperature-dependent current-voltage and admittance measurements revealed the removing of the deep level defect with the activation energy of 0.43 eV and the reducing of the ideality factor from 1.9 to 1.8 via buffer/absorber interfacial passivation method. Interface passivation appears to be critical to improve the short circuit current density and the open circuit voltage, and CdO thin film is clearly effective for this purpose.展开更多
Due to limited availability and the rising price of telluride, the biggest challenge in solar Photo-voltaic (PV) is to successfully design and fabricate optimized CdTe solar cells with reducing the cell thickness that...Due to limited availability and the rising price of telluride, the biggest challenge in solar Photo-voltaic (PV) is to successfully design and fabricate optimized CdTe solar cells with reducing the cell thickness that show simultaneously high efficiency and current density. A novel structure of ultrathin CdTe solar cells is proposed in this paper that focuses on conversion efficiency. This structure achieved by rotating 90o in the base line structure that suggests high efficiency due to the high current density. The result showed a considerable improvement over the 15% efficiency of the reference solar cell. The proposed structure is quite noteworthy in reducing the amount of material used and associated losses. Under global air mass (AM) 1.5 conditions, an open-circuit voltage (V<sub>oc</sub>) of 866 mV, a short-circuit current density (J<sub>sc</sub>) of 74.84 mA/cm<sup>2</sup>, and a fill factor (FF) of 48.2% were obtained corresponding to a conversion efficiency of 31.2%.展开更多
基金supported by the National Natural Science Foundation of China (Grant No. 60506004)the National High Technology Research and Development Program of China (Grant No. 2003AA513010)
文摘Deep levels in Cds/CdTe thin film solar cells have a potent influence on the electrical property of these devices. As an essential layer in the solar cell device structure, back contact is believed to induce some deep defects in the CdTe thin film. With the help of deep level transient spectroscopy （DLTS）, we study the deep levels in CdS/CdTe thin film solar cells with Te：Cu back contact. One hole trap and one electron trap are observed. The hole trap H1, localized at Ev＋0.128~eV, originates from the vacancy of Cd （VCd. The electron trap E1, found at Ec-0.178~eV, is considered to be correlated with the interstitial Cui= in CdTe.
文摘One of the most promising solar cell devices is cadmium telluride (CdTe) based. These cells however, have their own problems of stability and degradation in efficiency. Measurements show that CdS/CdTe solar cell has high series resistance which degrades the performance of solar cell energy conversion. Both active layers (CdS and CdTe) had been fabricated by thermal evaporation and tested individually. It was found that CdS window layer of 300 nm have the lowest series resistance with maximum light absorption. While 5 - 7 μm CdTe absorber layer absorbed more than 90% of the incident light with minimum series resistance. A complete CdS/CdTe solar cell was fabricated and tested. It was found that deposited cell without heat treatment shows that the short circuit current increment decreases as the light intensity increases. This type of deposited cell has low conversion efficiency. The energy conversion efficiency was improved by heat treatment, depositing heavily doped layer at the back of the cell and minimizing the contact resistivity by depositing material with resistivity less than 1 m??cm2. All these modifications were not enough because the back contact is non-ohmic. Tunnel diode of CdTe (p++)/CdS (n++) was deposited in the back of the cell. The energy conversion efficiency was improved by more than 7%.
文摘In this paper, interface engineering via sputtering of CdO nanolayer at the buffer-CdS/CdTe-absorber interface is demonstrated as an efficient approach to improve the performance of solar cell device. The i-CdO interfacial layer with various thicknesses from 5 nm to 35 nm was deposited by DC magnetron sputtering. Comparative studies on TCO/CdS/CdTe and TCO/CdS/CdO/CdTe interfaces have been conducted by current-voltage, capacitance-voltage and admittance spectroscopy measurements. The current-voltage characteristics of the devices with an area of 0.45 cm<sup>2</sup> under 100 mW/cm<sup>2</sup> illumination, at the optimum thickness of CdO intermediate layer in the proposed structures, show increases of the short circuit current density and the open circuit voltage by 5% and 25%, respectively. The efficiency improvement of 3.1% of p-i-n cell over p-n cell is observed. Results of the temperature-dependent current-voltage and admittance measurements revealed the removing of the deep level defect with the activation energy of 0.43 eV and the reducing of the ideality factor from 1.9 to 1.8 via buffer/absorber interfacial passivation method. Interface passivation appears to be critical to improve the short circuit current density and the open circuit voltage, and CdO thin film is clearly effective for this purpose.
文摘Due to limited availability and the rising price of telluride, the biggest challenge in solar Photo-voltaic (PV) is to successfully design and fabricate optimized CdTe solar cells with reducing the cell thickness that show simultaneously high efficiency and current density. A novel structure of ultrathin CdTe solar cells is proposed in this paper that focuses on conversion efficiency. This structure achieved by rotating 90o in the base line structure that suggests high efficiency due to the high current density. The result showed a considerable improvement over the 15% efficiency of the reference solar cell. The proposed structure is quite noteworthy in reducing the amount of material used and associated losses. Under global air mass (AM) 1.5 conditions, an open-circuit voltage (V<sub>oc</sub>) of 866 mV, a short-circuit current density (J<sub>sc</sub>) of 74.84 mA/cm<sup>2</sup>, and a fill factor (FF) of 48.2% were obtained corresponding to a conversion efficiency of 31.2%.
