Purpose–The precast concrete slab track(PST)has advantages of fewer maintenance frequencies,better smooth rides and structural stability,which has been widely applied in urban rail transit.Precise positioning of prec...Purpose–The precast concrete slab track(PST)has advantages of fewer maintenance frequencies,better smooth rides and structural stability,which has been widely applied in urban rail transit.Precise positioning of precast concrete slab(PCS)is vital for keeping the initial track regularity.However,the cast-in-place process of the self-compacting concrete(SCC)filling layer generally causes a large deformation of PCS due to the water-hammer effect of flowing SCC,even cracking of PCS.Currently,the buoyancy characteristic and influencing factors of PCS during the SCC casting process have not been thoroughly studied in urban rail transit.Design/methodology/approach–In this work,a Computational Fluid Dynamics(CFD)model is established to calculate the buoyancy of PCS caused by the flowing SCC.The main influencing factors,including the inlet speed and flowability of SCC,have been analyzed and discussed.A new structural optimization scheme has been proposed for PST to reduce the buoyancy caused by the flowing SCC.Findings–The simulation and field test results showed that the buoyancy and deformation of PCS decreased obviously after adopting the new scheme.Originality/value–The findings of this study can provide guidance for the control of the deformation of PCS during the SCC construction process.展开更多
The modified precipitation theory was employed to directly predict the multi-variantε-carbide precipitation from thermodynamics and growing and ripening kinetics.Three distinct variants were identified:Variants 1 and...The modified precipitation theory was employed to directly predict the multi-variantε-carbide precipitation from thermodynamics and growing and ripening kinetics.Three distinct variants were identified:Variants 1 and 2 were the perpendicular plate-likeε-carbides,while the granularε-carbides were Variant 3.The particle sizes of Variants 1 and 2 were usually larger than those of Variant 3.The mean aspect ratios of Variants 1 and 2 were 4.96,4.62 and 4.35 larger than those(1.72,1.63 and 1.56)for the granularε-carbides when coiled at 140,200 and 250℃,respectively.Thermodynamic analysis indicated that Variants 1 and 2 are easier to nucleate than Variant 3.The growing kinetic analysis implied that the relative nucleation time and precipitation time for Variants 1 and 2 were about 8 and 5 orders of magnitude less than those for Variant 3,respectively.The ripening kinetics further displayed that the ripening rate was similar for Variants 1,2 and 3.In addition,the dislocation density has weak influence onε-carbide nucleation.These findings suggest that the precipitation thermodynamic and kinetic models could be extended to second phase precipitation in other materials systems.Besides,nano-scaleε-carbides,fine block size and nano-twins,as well as medium-density dislocations,jointly caused the optimal match between strength and total elongation when coiled at 140℃.展开更多
Casting technology is a fundamental and irreplaceable method in advanced manufacturing.The design and optimization of casting processes are crucial for producing high-performance,complex metal components.Transitioning...Casting technology is a fundamental and irreplaceable method in advanced manufacturing.The design and optimization of casting processes are crucial for producing high-performance,complex metal components.Transitioning from traditional process design based on"experience+experiment"to an integrated,intelligent approach is essential for achieving precise control over microstructure and properties.This paper provides a comprehensive and systematic review of intelligent casting process design and optimization for the first time.First,it explores process design methods based on casting simulation and integrated computational materials engineering(ICME).It then examines the application of machine learning(ML)in process design,highlighting its efficiency and existing challenges,along with the development of integrated intelligent design platforms.Finally,future research directions are discussed to drive further advancements and sustainable development in intelligent casting design and optimization.展开更多
A new process for swirling flow generation in the submerged entry nozzle （SEN） in continuous casting process of steel was proposed. A rotating electromagnetic field was set up around the SEN to induce swirling flow ...A new process for swirling flow generation in the submerged entry nozzle （SEN） in continuous casting process of steel was proposed. A rotating electromagnetic field was set up around the SEN to induce swirling flow by Lorentz force. The flow and temperature fields in the SEN and round billet mold with electromagnetic swirling were numerically simulated and then verified by the electromagnetic swirling model experiment of low melting point alloy. The effects of divergent angle of the SEN on the flow and temperature fields in mold with electromagnetic swirling were investigated. The electromagnetic swirling flow generator （EMSFG） could effectively induce swirling flow of molten steel in the SEN, which consequently improved greatly the flow and temperature fields in the mold. Below the nozzle outlet in mold, with the increase of divergent angle, the stream of bulk flow diverged more widely, the high temperature zone shifted up, and the temperature field became more uniform. Above the nozzle outlet in mold, with 350 A electromagnetic swirling, when the divergent angle of the SEN increased, the upward flow velocity and the meniscus temperature first increased and then decreased. With a divergent angle of 60~, the upward flow velocity and meniscus temperature reaced the largest value.展开更多
A 3-D mathematical model considering turbulence phenomena has been established based on a computational fluid dynamics technique, so called 3-D SOLA-VOF (Solution Algorithm-Volume of Fluid), to simulate the fluid flow...A 3-D mathematical model considering turbulence phenomena has been established based on a computational fluid dynamics technique, so called 3-D SOLA-VOF (Solution Algorithm-Volume of Fluid), to simulate the fluid flow of mold filling process of die casting. In addition, the mathematical model for simulating the heat transfer in die casting process has also been established. The computation program has been developed by the authors with the finite difference method (FDM) recently. As verification, the mold filling process of a S-shaped die casting has been simulated and the simulation results coincide with that of the benchmark test. Finally, as a practical application, the gating design of a motorcycle component was modified by the mold filling simulation and the dies design of another motorcycle component was optimized by the heat transfer simulation. All the optimized designs were verified by the production practice.展开更多
The models, algorithms and implementation results of a computerized scheduling system were introduced for the steelmaking-continuous casting process （SCCP） of a steel plant in China. The scheduling of SCCP in this p...The models, algorithms and implementation results of a computerized scheduling system were introduced for the steelmaking-continuous casting process （SCCP） of a steel plant in China. The scheduling of SCCP in this plant required that each cast plan should be processed on time, the charges in the same cast should be processed con- tinuously on the same caster, and the waiting time of the charges which are in front of each caster cannot exceed the given threshold. At the same time, the processing time of charges cannot be conflicted mutually in the same convert- ers or refining furnaces. Based on the research background, a hybrid optimal scheduling approach and its application were discussed. Aiming at the main equipment scheduling, an optimal scheduling method was proposed which con- sisted of equipment assignment algorithm based on dynamic program （DP） technique and conflict elimination algo rithm based on linear program （LP） technique. The approach guarantees that the charges are continuously processed on the same caster. Meanwhile, the requirement for high temperature ladle can also be satisfied due to the ladle matching function. Numerical results demonstrate solution quality, computational efficiency, and values of the mod els and algorithm.展开更多
Given the nonuse of TiO2 nanoparticles as the reinforcement of AA2024 alloy in fabricating composites by ex-situ casting methods,it was decided to process the AA2024−xTiO2(np)(x=0,0.5 and 1 vol.%)nanocomposites by emp...Given the nonuse of TiO2 nanoparticles as the reinforcement of AA2024 alloy in fabricating composites by ex-situ casting methods,it was decided to process the AA2024−xTiO2(np)(x=0,0.5 and 1 vol.%)nanocomposites by employing the stir casting method.The structural properties of the produced samples were then investigated by optical microscopy and scanning electron microscopy;their mechanical properties were also addressed by hardness and tensile tests.The results showed that adding 1 vol.%TiO2 nanoparticles reduced the grain size and dendrite arm spacing by about 66%and 31%,respectively.Also,hardness,ultimate tensile strength,yield strength,and elongation of AA2024−1vol.%TiO2(np)composite were increased by about 25%,28%,4%and 163%,respectively,as compared to those of the monolithic component.The agglomerations of nanoparticles in the structure of nanocomposites were found to be a factor weakening the strength against the strengthening mechanisms.Some agglomerations of nanoparticles in the matrix were detected on the fractured surfaces of the tension test specimens.展开更多
Sliding gate control system is widely employed in continuous casting process of steel to control flow rate of molten steel.As molten steel passes through a sliding gate,uneven flow develops.This will cause asymmetrica...Sliding gate control system is widely employed in continuous casting process of steel to control flow rate of molten steel.As molten steel passes through a sliding gate,uneven flow develops.This will cause asymmetrical distribution of flow and temperature field in mold consequently,formation of vortex near the nozzle and entrapment of CC powder into the molten steel.etc,which have negative effect on process productivity and product quality.To suppress the uneven flow,electromagnetic swirling flow has been proposed to impose on the flow in submerged entry nozzle below the sliding gate.In this study the uneven flow developed by incompletely open sliding gate and the suppression of this uneven flow using electromagnetic swirling flow are numerically studied in round billet continuous casting of steel process.The improvement of the flow and temperature filed in the submerged entry nozzle and mold are investigated.It is found that:The uneven velocity in nozzle can be suppressed by electromagnetic swirling flow,and the flow and temperature field in mold be improved obviously;With the increase of electromagnetic swirling intensity,the effect of uneven flow can be almost completely suppressed.展开更多
Optimization of casting process involves the adjustment of parameters as well as the improvement of process schemes and measures.This paper proposes a new method based on the Theory of Inventive Problem Solving(TRIZ) ...Optimization of casting process involves the adjustment of parameters as well as the improvement of process schemes and measures.This paper proposes a new method based on the Theory of Inventive Problem Solving(TRIZ) for casting process optimization,and realizes the idea of applying TRIZ to optimize the casting process of a magnesium alloy intake manifold.By this method,the casting process is optimized so as to remove the shrinkage pores.The successful optimization of casting process demonstrates the feasibility of the proposed method.展开更多
In this study, the effect of melting temperature on the microstructural evolutions, behavior, and corrosion morphology of Hadfield steel in the casting process is investigated. The mold was prepared by the sodium sili...In this study, the effect of melting temperature on the microstructural evolutions, behavior, and corrosion morphology of Hadfield steel in the casting process is investigated. The mold was prepared by the sodium silicate/CO_2 method, using a blind riser, and then the desired molten steel was obtained using a coreless induction furnace. The casting was performed at melting temperatures of 1350, 1400, 1450, and 1500°C, and the cast blocks were immediately quenched in water. Optical microscopy was used to analyze the microstructure, and scanning electron microscopy(SEM) and X-ray diffractrometry(XRD) were used to analyze the corrosion morphology and phase formation in the microstructure, respectively. The corrosion behavior of the samples was analyzed using a potentiodynamic polarization test and electrochemical impedance spectroscopy(EIS) in 3.5 wt% NaCl. The optical microscopy observations and XRD patterns show that the increase in melting temperature led to a decrease of carbides and an increase in the austenite grain size in the Hadfield steel microstructure. The corrosion tests results show that with increasing melting temperature in the casting process, Hadfield steel shows a higher corrosion resistance. The SEM images of the corrosion morphologies show that the reduction of melting temperature in the Hadfield steel casting process induced micro-galvanic corrosion conditions.展开更多
The gating system and the overflow system were designed according to the casting structure during high pressure die casting(HPDC) process. The simulation was carried out by ProCAST software to visualize the injection ...The gating system and the overflow system were designed according to the casting structure during high pressure die casting(HPDC) process. The simulation was carried out by ProCAST software to visualize the injection chamber pre-crystallization and the flow of molten metal. The main work is to research four die casting process parameters, i.e. injection temperature, low-pressure velocity, high-and low-pressure velocity’s switching position, and high-pressure velocity. Experimental results show that the higher injection temperature and lowpressure velocity can mitigate the pre-crystallization of the injection chamber. However, when the low-pressure velocity exceeds 0.2 m·s-1, the air entrapment in the chamber occurs. Besides, when the high-pressure velocity is greater than 2.5 m·s-1, the overflow channel at the final filling position is covered by the liquid metal too early. Finally, the injection temperature of 650 °C, the low-pressure velocity of 0.2 m·s-1, the high-and low-pressure velocity’s switching position of 320 mm and the high-pressure velocity of 2 m·s-1 are obtained as the optimal parameters by the software simulation, which has been verified by actual production.展开更多
The microstructure and mechanical properties of magnesium （Mg） alloys are significantly influenced by the casting process. In this paper, a comparative study on microstructure and mechanical properties at ambient an...The microstructure and mechanical properties of magnesium （Mg） alloys are significantly influenced by the casting process. In this paper, a comparative study on microstructure and mechanical properties at ambient and elevated temperatures of AZ91-2wt.% Ca （AZX912） Mg alloy samples prepared by gravity casting （GC）, squeeze casting （SC） and rheo-squeeze casting （RSC）, respectively, was carried out. The results show that mMg grains in SC and RSC samples are significantly refined compared to the GC sample. The average secondary dendritic arm spacing of AZX912 alloy samples decreases in the order of GC, SC and RSC. As testing temperature increases from 25 ~C to 200 ~C, strength of AZX912 alloy samples is reduced, while their elongation is increased continuously. Compared to GC and SC processes, RSC process can improve the mechanical properties of AZX912 alloy at both ambient and elevated temperatures. The enhancement of mechanical properties of RSC sample over GC and SC samples mainly results from grain refinement in the as-cast microstructure of AZX912 alloy.展开更多
High pressure die casting (HPDC) is a versatile material processing method for mass-production of metal parts with complex geometries,and this method has been widely used in manufacturing various products of excellent...High pressure die casting (HPDC) is a versatile material processing method for mass-production of metal parts with complex geometries,and this method has been widely used in manufacturing various products of excellent dimensional accuracy and productivity. In order to ensure the quality of the components,a number of variables need to be properly set. A novel methodology for high pressure die casting process optimization was developed,validated and applied to selection of optimal parameters,which incorporate design of experiment (DOE),Gaussian process (GP) regression technique and genetic algorithms (GA). This new approach was applied to process optimization for cast magnesium alloy notebook shell. After being trained,using data generated by PROCAST (FEM-based simulation software),the GP model approximated well with the simulation by extracting useful information from the simulation results. With the help of MATLAB,the GP/GA based approach has achieved the optimum solution of die casting process condition settings.展开更多
Swirling flow in a submerged entry nozzle is effective on improving quality of casting block and casting speed in continuous casting of steel.A new method for swirling flow generation in the nozzle has been proposed b...Swirling flow in a submerged entry nozzle is effective on improving quality of casting block and casting speed in continuous casting of steel.A new method for swirling flow generation in the nozzle has been proposed by the authors,that is a rotating electromagnetic field is set up around a submerged entry nozzle(SEN)to induce swirling flow in it by Lorentz force.In this study,the magnetic field in molten steel in the submerged entry nozzle,the flow and temperature field in the SEN and mold in round,square billet and slab continuous casting process of steel are numerically studied.The model experiment of electromagnetic swirling continuous casting is also conducted with low melting point alloy.The commercial test for slab is undergoing.Results by numerical simulation and experiment show that the swirling flow by the optimum designed electromagnetic swirling generator can not only improve the distribution of flow and temperature in mold but also achieve the same effects generated by the swirling blade process. And,more effects on continuous casting process can be expected after this electromagnetic swirling process is optimized.展开更多
The effects of Sr addition and pressure increase on the microstructure and casting defects of a low-pressure die cast （LPDC） AISi7Mg0.3 alloy have been studied. Metallographic and image analysis techniques have been...The effects of Sr addition and pressure increase on the microstructure and casting defects of a low-pressure die cast （LPDC） AISi7Mg0.3 alloy have been studied. Metallographic and image analysis techniques have been used to quantitatively examine the microstructural changes and the amount of porosity occurring at different Sr levels and pressure parameters. The results indicate that an increase in the filling pressure induces lower heat dissipation of the liquid close to the die/core surfaces, with the formation of slightly greater dendrite arms and coarser eutectic Si particles. On the other hand, the increase in the Sr level leads to finer microstructural scale and eutectic Si. The analysed variables, within the experimental conditions, do not affect the morphology of eutectic Si particles. Higher applied pressure and Sr content generate castings with lower amount of porosiW. However, as the filling pressure increases the flow of metal inside the die cavity is more turbulent, leading to the formation of oxide films and cold shots. In the analysed range of experimental conditions, the design of experiment methodology and the analysis of variance have been used to develop statistical models that accurately predict the average size of secondary dendrite arm spacing and the amount of porosity in the low-pressure die cast AISiTMg0.3 alloy.展开更多
The bonding quality of bronze/steel bimetallic laminated composite is the key factor to whether it can be used in poor working conditions.In this study,bimetallic billets were prepared by the protective atmosphere cas...The bonding quality of bronze/steel bimetallic laminated composite is the key factor to whether it can be used in poor working conditions.In this study,bimetallic billets were prepared by the protective atmosphere casting process.The microstructural characteristics,mechanical properties and interface bonding mechanism of the bronze/steel bimetallic composites were analyzed comprehensively through a series of microstructure analysis(inicluding OM,SEM,and EDS)and mechanical properties tests.The experimental results demonstrate that the vaporization of lead(Pb)element in the bronze is only 0.4%in weight,and alloy elements are diffused into both sides at the interface.Moreover,the hardness in the bronze region exceeds 100.0 HV which indicates excellent wear resistance.Tensile and shear tests indicate that the fractures mainly occur on the bronze side with the interaction of the brittle fracture of Pb particles and the ductile fracture of Cu-Sn solid solution.The maximum tensile strength and shear strength reach 204.0 MPa and 211.0 MPa,respectively.These results demonstrate that the protective atmosphere casting process is applicable for the preparation of bronze/steel bimetallic laminated composite with high quality.展开更多
Numerical simulation of casting＇s mold filling process is the main and the most important aspect of the foundry CAE technology. But it is time-consuming; it may take dozens of hours or several days. While with the de...Numerical simulation of casting＇s mold filling process is the main and the most important aspect of the foundry CAE technology. But it is time-consuming; it may take dozens of hours or several days. While with the development of computer hardware, numerical simulation of casting＇ s mold filling process has made rapid progress. The simulation results, therefore, have become more and more practical. This study tries to find some clues of the computational time of mold filling process. Firstly, this paper introduces mathematic model and the basic route of numerical simulation of casting＇s mold filling process. Then the computational time of mold filling process has been carefully studied, and some new and useful results have been gained from the study of the computational time. Finally, this paper has given some real applications of numerical simulation of casting＇s mold filling process.展开更多
Semisolid continuous casting (SSCC) is a new technology to produce billets for semisolid metal forming (SSMF). The effect of process factors, such as pouring temperature, stirring rate, preheating temperature and ther...Semisolid continuous casting (SSCC) is a new technology to produce billets for semisolid metal forming (SSMF). The effect of process factors, such as pouring temperature, stirring rate, preheating temperature and thermal conductivity of stirring chamber, on the microstructure of SSCC billets was studied by means of the factorial experimental method. The results show that the microstructure of SSCC billets can be controlled by the above-mentioned four process factors. In order to obtain fine and rounded granular grains in an SSCC billet, the pouring temperature, preheating temperature and stirring rate should be kept in a moderate range, and the thermal conductivity of stirring chamber should be high. The regression equations with the process factors connecting the microstructure was also set up based on experimental data.展开更多
Most lost-foam casting processes involve non-equilibrium solidification dominated by kinetic factors, while construction of a common dynamic solidification curve is based on pure thermodynamics, not applicable for ana...Most lost-foam casting processes involve non-equilibrium solidification dominated by kinetic factors, while construction of a common dynamic solidification curve is based on pure thermodynamics, not applicable for analyses and research of non-equilibrium macro-solidification processes, and the construction mode can not be applied to nonequilibrium solidification process. In this study, the construction of the dynamic solidification curve(DSC) for the nonequilibrium macro-solidification process included: a modified method to determine the start temperature of primary austenite precipitation(T_(AL)) and the start temperature of eutectic solidification(T_(ES)); double curves method to determine the temperature of the dendrite coherency point of primary austenite(T-(AC)) and the temperature of eutectic cells collision point(T_(EC)); the "technical solidus" method to determine the end temperature of eutectic reaction(T_(EN)). For this purpose, a comparative testing of the non-equilibrium solidification temperature fields in lost-foam casting and green sand mold casting hypoeutectic gray iron was carried out. The thermal analysis results were used to construct the DSCs of both these casting methods under non-equilibrium solidification conditions. The results show that the transformation rate of non-equilibrium solidification in hypoeutectic gray cast iron is greater than that of equilibrium solidification. The eutectic solidification region presents a typical mushy solidification mode. The results also indicate that the primary austenite precipitation zone of lost-foam casting is slightly larger than that of green sand casting. At the same time, the solid fraction(f_s) of the dendrite coherency points in lost-foam casting is greater than that in the green sand casting. Therefore, from these two points, lost-foam casting is more preferable for reduction of shrinkage and mechanical burntin sand tendency of the hypoeutectic gray cast iron. Due to the fact that the solidification process(from the surface to center) at primary austenite growth area in the lost-foam cylinder sample lags behind that in the green sand casting, the mushy solidification tendency of lost-foam casting is greater and the solidification time is longer.展开更多
A design of experiment technique was used to optimize the microstructure of the AZ91D alloy produced by rheo-casting. The experimental design consists of four parameters(pouring temperature,shearing temperature,sheari...A design of experiment technique was used to optimize the microstructure of the AZ91D alloy produced by rheo-casting. The experimental design consists of four parameters(pouring temperature,shearing temperature,shearing time and shearing rate) with three levels.The grain size and shape factor measurements of primaryα-Mg particles were conducted to determine the microstructure.The contribution of each parameter shows that pouring temperature is the most significant parameter affecting the grain size,and the shape factor highly depends on the shearing temperature.The optimized rheo-casting processing parameters are 650 C for pouring temperature,585℃for shearing temperature,40 s for shearing time,and 600 r/min for shearing rate.Under the optimized processing parameters,the average grain size is 28.53μm,and the shape factor is 0.591.展开更多
文摘Purpose–The precast concrete slab track(PST)has advantages of fewer maintenance frequencies,better smooth rides and structural stability,which has been widely applied in urban rail transit.Precise positioning of precast concrete slab(PCS)is vital for keeping the initial track regularity.However,the cast-in-place process of the self-compacting concrete(SCC)filling layer generally causes a large deformation of PCS due to the water-hammer effect of flowing SCC,even cracking of PCS.Currently,the buoyancy characteristic and influencing factors of PCS during the SCC casting process have not been thoroughly studied in urban rail transit.Design/methodology/approach–In this work,a Computational Fluid Dynamics(CFD)model is established to calculate the buoyancy of PCS caused by the flowing SCC.The main influencing factors,including the inlet speed and flowability of SCC,have been analyzed and discussed.A new structural optimization scheme has been proposed for PST to reduce the buoyancy caused by the flowing SCC.Findings–The simulation and field test results showed that the buoyancy and deformation of PCS decreased obviously after adopting the new scheme.Originality/value–The findings of this study can provide guidance for the control of the deformation of PCS during the SCC construction process.
基金supported by the National Natural Science Foundation of China(No.52293395)National Key R&D Program of China(No.2021YFB3702403).
文摘The modified precipitation theory was employed to directly predict the multi-variantε-carbide precipitation from thermodynamics and growing and ripening kinetics.Three distinct variants were identified:Variants 1 and 2 were the perpendicular plate-likeε-carbides,while the granularε-carbides were Variant 3.The particle sizes of Variants 1 and 2 were usually larger than those of Variant 3.The mean aspect ratios of Variants 1 and 2 were 4.96,4.62 and 4.35 larger than those(1.72,1.63 and 1.56)for the granularε-carbides when coiled at 140,200 and 250℃,respectively.Thermodynamic analysis indicated that Variants 1 and 2 are easier to nucleate than Variant 3.The growing kinetic analysis implied that the relative nucleation time and precipitation time for Variants 1 and 2 were about 8 and 5 orders of magnitude less than those for Variant 3,respectively.The ripening kinetics further displayed that the ripening rate was similar for Variants 1,2 and 3.In addition,the dislocation density has weak influence onε-carbide nucleation.These findings suggest that the precipitation thermodynamic and kinetic models could be extended to second phase precipitation in other materials systems.Besides,nano-scaleε-carbides,fine block size and nano-twins,as well as medium-density dislocations,jointly caused the optimal match between strength and total elongation when coiled at 140℃.
基金supported by the National Natural Science Foundation of China(No.52074246)the National Defense Basic Scientific Research Program of China(No.JCKY2020408B002)+1 种基金the Key R&D Program of Shanxi Province(No.202102050201011)the Shanxi Province Graduate Innovation Project(No.2021Y591).
文摘Casting technology is a fundamental and irreplaceable method in advanced manufacturing.The design and optimization of casting processes are crucial for producing high-performance,complex metal components.Transitioning from traditional process design based on"experience+experiment"to an integrated,intelligent approach is essential for achieving precise control over microstructure and properties.This paper provides a comprehensive and systematic review of intelligent casting process design and optimization for the first time.First,it explores process design methods based on casting simulation and integrated computational materials engineering(ICME).It then examines the application of machine learning(ML)in process design,highlighting its efficiency and existing challenges,along with the development of integrated intelligent design platforms.Finally,future research directions are discussed to drive further advancements and sustainable development in intelligent casting design and optimization.
基金Item Sponsored by Fundamental Research Funds for Central Universities of China(N100409010)Project for Key Laboratory of Liaoning Province of China(LS2010065)"111 Project"of Northeastern University of China(B07015)
文摘A new process for swirling flow generation in the submerged entry nozzle （SEN） in continuous casting process of steel was proposed. A rotating electromagnetic field was set up around the SEN to induce swirling flow by Lorentz force. The flow and temperature fields in the SEN and round billet mold with electromagnetic swirling were numerically simulated and then verified by the electromagnetic swirling model experiment of low melting point alloy. The effects of divergent angle of the SEN on the flow and temperature fields in mold with electromagnetic swirling were investigated. The electromagnetic swirling flow generator （EMSFG） could effectively induce swirling flow of molten steel in the SEN, which consequently improved greatly the flow and temperature fields in the mold. Below the nozzle outlet in mold, with the increase of divergent angle, the stream of bulk flow diverged more widely, the high temperature zone shifted up, and the temperature field became more uniform. Above the nozzle outlet in mold, with 350 A electromagnetic swirling, when the divergent angle of the SEN increased, the upward flow velocity and the meniscus temperature first increased and then decreased. With a divergent angle of 60~, the upward flow velocity and meniscus temperature reaced the largest value.
文摘A 3-D mathematical model considering turbulence phenomena has been established based on a computational fluid dynamics technique, so called 3-D SOLA-VOF (Solution Algorithm-Volume of Fluid), to simulate the fluid flow of mold filling process of die casting. In addition, the mathematical model for simulating the heat transfer in die casting process has also been established. The computation program has been developed by the authors with the finite difference method (FDM) recently. As verification, the mold filling process of a S-shaped die casting has been simulated and the simulation results coincide with that of the benchmark test. Finally, as a practical application, the gating design of a motorcycle component was modified by the mold filling simulation and the dies design of another motorcycle component was optimized by the heat transfer simulation. All the optimized designs were verified by the production practice.
基金Item Sponsored by National Natural Science Foundation of China(61174187,71021061,60974091,61104174)Startup Fund of Northeastern University of China(29321006)Basic Scientific Research Foundation of Northeast University of China(N110208001)
文摘The models, algorithms and implementation results of a computerized scheduling system were introduced for the steelmaking-continuous casting process （SCCP） of a steel plant in China. The scheduling of SCCP in this plant required that each cast plan should be processed on time, the charges in the same cast should be processed con- tinuously on the same caster, and the waiting time of the charges which are in front of each caster cannot exceed the given threshold. At the same time, the processing time of charges cannot be conflicted mutually in the same convert- ers or refining furnaces. Based on the research background, a hybrid optimal scheduling approach and its application were discussed. Aiming at the main equipment scheduling, an optimal scheduling method was proposed which con- sisted of equipment assignment algorithm based on dynamic program （DP） technique and conflict elimination algo rithm based on linear program （LP） technique. The approach guarantees that the charges are continuously processed on the same caster. Meanwhile, the requirement for high temperature ladle can also be satisfied due to the ladle matching function. Numerical results demonstrate solution quality, computational efficiency, and values of the mod els and algorithm.
文摘Given the nonuse of TiO2 nanoparticles as the reinforcement of AA2024 alloy in fabricating composites by ex-situ casting methods,it was decided to process the AA2024−xTiO2(np)(x=0,0.5 and 1 vol.%)nanocomposites by employing the stir casting method.The structural properties of the produced samples were then investigated by optical microscopy and scanning electron microscopy;their mechanical properties were also addressed by hardness and tensile tests.The results showed that adding 1 vol.%TiO2 nanoparticles reduced the grain size and dendrite arm spacing by about 66%and 31%,respectively.Also,hardness,ultimate tensile strength,yield strength,and elongation of AA2024−1vol.%TiO2(np)composite were increased by about 25%,28%,4%and 163%,respectively,as compared to those of the monolithic component.The agglomerations of nanoparticles in the structure of nanocomposites were found to be a factor weakening the strength against the strengthening mechanisms.Some agglomerations of nanoparticles in the matrix were detected on the fractured surfaces of the tension test specimens.
基金Item Sponsored by The Central Universities(N100409010)Project for Key Laboratory of Liaoning Province(LS2010065)"111 project" of Northeastern University,China(B07015)
文摘Sliding gate control system is widely employed in continuous casting process of steel to control flow rate of molten steel.As molten steel passes through a sliding gate,uneven flow develops.This will cause asymmetrical distribution of flow and temperature field in mold consequently,formation of vortex near the nozzle and entrapment of CC powder into the molten steel.etc,which have negative effect on process productivity and product quality.To suppress the uneven flow,electromagnetic swirling flow has been proposed to impose on the flow in submerged entry nozzle below the sliding gate.In this study the uneven flow developed by incompletely open sliding gate and the suppression of this uneven flow using electromagnetic swirling flow are numerically studied in round billet continuous casting of steel process.The improvement of the flow and temperature filed in the submerged entry nozzle and mold are investigated.It is found that:The uneven velocity in nozzle can be suppressed by electromagnetic swirling flow,and the flow and temperature field in mold be improved obviously;With the increase of electromagnetic swirling intensity,the effect of uneven flow can be almost completely suppressed.
基金supported by the Innovative Methods Special Project (No. 2009IM040200)
文摘Optimization of casting process involves the adjustment of parameters as well as the improvement of process schemes and measures.This paper proposes a new method based on the Theory of Inventive Problem Solving(TRIZ) for casting process optimization,and realizes the idea of applying TRIZ to optimize the casting process of a magnesium alloy intake manifold.By this method,the casting process is optimized so as to remove the shrinkage pores.The successful optimization of casting process demonstrates the feasibility of the proposed method.
文摘In this study, the effect of melting temperature on the microstructural evolutions, behavior, and corrosion morphology of Hadfield steel in the casting process is investigated. The mold was prepared by the sodium silicate/CO_2 method, using a blind riser, and then the desired molten steel was obtained using a coreless induction furnace. The casting was performed at melting temperatures of 1350, 1400, 1450, and 1500°C, and the cast blocks were immediately quenched in water. Optical microscopy was used to analyze the microstructure, and scanning electron microscopy(SEM) and X-ray diffractrometry(XRD) were used to analyze the corrosion morphology and phase formation in the microstructure, respectively. The corrosion behavior of the samples was analyzed using a potentiodynamic polarization test and electrochemical impedance spectroscopy(EIS) in 3.5 wt% NaCl. The optical microscopy observations and XRD patterns show that the increase in melting temperature led to a decrease of carbides and an increase in the austenite grain size in the Hadfield steel microstructure. The corrosion tests results show that with increasing melting temperature in the casting process, Hadfield steel shows a higher corrosion resistance. The SEM images of the corrosion morphologies show that the reduction of melting temperature in the Hadfield steel casting process induced micro-galvanic corrosion conditions.
基金financially supported by the National Key Research and Development Program of China(No.2016YFB0301003)
文摘The gating system and the overflow system were designed according to the casting structure during high pressure die casting(HPDC) process. The simulation was carried out by ProCAST software to visualize the injection chamber pre-crystallization and the flow of molten metal. The main work is to research four die casting process parameters, i.e. injection temperature, low-pressure velocity, high-and low-pressure velocity’s switching position, and high-pressure velocity. Experimental results show that the higher injection temperature and lowpressure velocity can mitigate the pre-crystallization of the injection chamber. However, when the low-pressure velocity exceeds 0.2 m·s-1, the air entrapment in the chamber occurs. Besides, when the high-pressure velocity is greater than 2.5 m·s-1, the overflow channel at the final filling position is covered by the liquid metal too early. Finally, the injection temperature of 650 °C, the low-pressure velocity of 0.2 m·s-1, the high-and low-pressure velocity’s switching position of 320 mm and the high-pressure velocity of 2 m·s-1 are obtained as the optimal parameters by the software simulation, which has been verified by actual production.
基金financially supported by the National Natural Science Foundation of China(No.51601076)the Natural Science Fund for Colleges and Universities in Jiangsu Province(No.16KJB430013,17KJA430005)
文摘The microstructure and mechanical properties of magnesium （Mg） alloys are significantly influenced by the casting process. In this paper, a comparative study on microstructure and mechanical properties at ambient and elevated temperatures of AZ91-2wt.% Ca （AZX912） Mg alloy samples prepared by gravity casting （GC）, squeeze casting （SC） and rheo-squeeze casting （RSC）, respectively, was carried out. The results show that mMg grains in SC and RSC samples are significantly refined compared to the GC sample. The average secondary dendritic arm spacing of AZX912 alloy samples decreases in the order of GC, SC and RSC. As testing temperature increases from 25 ~C to 200 ~C, strength of AZX912 alloy samples is reduced, while their elongation is increased continuously. Compared to GC and SC processes, RSC process can improve the mechanical properties of AZX912 alloy at both ambient and elevated temperatures. The enhancement of mechanical properties of RSC sample over GC and SC samples mainly results from grain refinement in the as-cast microstructure of AZX912 alloy.
文摘High pressure die casting (HPDC) is a versatile material processing method for mass-production of metal parts with complex geometries,and this method has been widely used in manufacturing various products of excellent dimensional accuracy and productivity. In order to ensure the quality of the components,a number of variables need to be properly set. A novel methodology for high pressure die casting process optimization was developed,validated and applied to selection of optimal parameters,which incorporate design of experiment (DOE),Gaussian process (GP) regression technique and genetic algorithms (GA). This new approach was applied to process optimization for cast magnesium alloy notebook shell. After being trained,using data generated by PROCAST (FEM-based simulation software),the GP model approximated well with the simulation by extracting useful information from the simulation results. With the help of MATLAB,the GP/GA based approach has achieved the optimum solution of die casting process condition settings.
基金Item Sponsored by Central Universities(N100409010)Project for Key Laboratory of Liaoning Province(LS2010065)"111 project" of Northeastern University,China(B07015)
文摘Swirling flow in a submerged entry nozzle is effective on improving quality of casting block and casting speed in continuous casting of steel.A new method for swirling flow generation in the nozzle has been proposed by the authors,that is a rotating electromagnetic field is set up around a submerged entry nozzle(SEN)to induce swirling flow in it by Lorentz force.In this study,the magnetic field in molten steel in the submerged entry nozzle,the flow and temperature field in the SEN and mold in round,square billet and slab continuous casting process of steel are numerically studied.The model experiment of electromagnetic swirling continuous casting is also conducted with low melting point alloy.The commercial test for slab is undergoing.Results by numerical simulation and experiment show that the swirling flow by the optimum designed electromagnetic swirling generator can not only improve the distribution of flow and temperature in mold but also achieve the same effects generated by the swirling blade process. And,more effects on continuous casting process can be expected after this electromagnetic swirling process is optimized.
文摘The effects of Sr addition and pressure increase on the microstructure and casting defects of a low-pressure die cast （LPDC） AISi7Mg0.3 alloy have been studied. Metallographic and image analysis techniques have been used to quantitatively examine the microstructural changes and the amount of porosity occurring at different Sr levels and pressure parameters. The results indicate that an increase in the filling pressure induces lower heat dissipation of the liquid close to the die/core surfaces, with the formation of slightly greater dendrite arms and coarser eutectic Si particles. On the other hand, the increase in the Sr level leads to finer microstructural scale and eutectic Si. The analysed variables, within the experimental conditions, do not affect the morphology of eutectic Si particles. Higher applied pressure and Sr content generate castings with lower amount of porosiW. However, as the filling pressure increases the flow of metal inside the die cavity is more turbulent, leading to the formation of oxide films and cold shots. In the analysed range of experimental conditions, the design of experiment methodology and the analysis of variance have been used to develop statistical models that accurately predict the average size of secondary dendrite arm spacing and the amount of porosity in the low-pressure die cast AISiTMg0.3 alloy.
文摘The bonding quality of bronze/steel bimetallic laminated composite is the key factor to whether it can be used in poor working conditions.In this study,bimetallic billets were prepared by the protective atmosphere casting process.The microstructural characteristics,mechanical properties and interface bonding mechanism of the bronze/steel bimetallic composites were analyzed comprehensively through a series of microstructure analysis(inicluding OM,SEM,and EDS)and mechanical properties tests.The experimental results demonstrate that the vaporization of lead(Pb)element in the bronze is only 0.4%in weight,and alloy elements are diffused into both sides at the interface.Moreover,the hardness in the bronze region exceeds 100.0 HV which indicates excellent wear resistance.Tensile and shear tests indicate that the fractures mainly occur on the bronze side with the interaction of the brittle fracture of Pb particles and the ductile fracture of Cu-Sn solid solution.The maximum tensile strength and shear strength reach 204.0 MPa and 211.0 MPa,respectively.These results demonstrate that the protective atmosphere casting process is applicable for the preparation of bronze/steel bimetallic laminated composite with high quality.
文摘Numerical simulation of casting＇s mold filling process is the main and the most important aspect of the foundry CAE technology. But it is time-consuming; it may take dozens of hours or several days. While with the development of computer hardware, numerical simulation of casting＇ s mold filling process has made rapid progress. The simulation results, therefore, have become more and more practical. This study tries to find some clues of the computational time of mold filling process. Firstly, this paper introduces mathematic model and the basic route of numerical simulation of casting＇s mold filling process. Then the computational time of mold filling process has been carefully studied, and some new and useful results have been gained from the study of the computational time. Finally, this paper has given some real applications of numerical simulation of casting＇s mold filling process.
基金This work was financed by the NatUral Science Research Fotmdation of Hebei Province, China and the NatUral Science Researc
文摘Semisolid continuous casting (SSCC) is a new technology to produce billets for semisolid metal forming (SSMF). The effect of process factors, such as pouring temperature, stirring rate, preheating temperature and thermal conductivity of stirring chamber, on the microstructure of SSCC billets was studied by means of the factorial experimental method. The results show that the microstructure of SSCC billets can be controlled by the above-mentioned four process factors. In order to obtain fine and rounded granular grains in an SSCC billet, the pouring temperature, preheating temperature and stirring rate should be kept in a moderate range, and the thermal conductivity of stirring chamber should be high. The regression equations with the process factors connecting the microstructure was also set up based on experimental data.
基金financially supported by the National Development and Reform Commission(2010-324)
文摘Most lost-foam casting processes involve non-equilibrium solidification dominated by kinetic factors, while construction of a common dynamic solidification curve is based on pure thermodynamics, not applicable for analyses and research of non-equilibrium macro-solidification processes, and the construction mode can not be applied to nonequilibrium solidification process. In this study, the construction of the dynamic solidification curve(DSC) for the nonequilibrium macro-solidification process included: a modified method to determine the start temperature of primary austenite precipitation(T_(AL)) and the start temperature of eutectic solidification(T_(ES)); double curves method to determine the temperature of the dendrite coherency point of primary austenite(T-(AC)) and the temperature of eutectic cells collision point(T_(EC)); the "technical solidus" method to determine the end temperature of eutectic reaction(T_(EN)). For this purpose, a comparative testing of the non-equilibrium solidification temperature fields in lost-foam casting and green sand mold casting hypoeutectic gray iron was carried out. The thermal analysis results were used to construct the DSCs of both these casting methods under non-equilibrium solidification conditions. The results show that the transformation rate of non-equilibrium solidification in hypoeutectic gray cast iron is greater than that of equilibrium solidification. The eutectic solidification region presents a typical mushy solidification mode. The results also indicate that the primary austenite precipitation zone of lost-foam casting is slightly larger than that of green sand casting. At the same time, the solid fraction(f_s) of the dendrite coherency points in lost-foam casting is greater than that in the green sand casting. Therefore, from these two points, lost-foam casting is more preferable for reduction of shrinkage and mechanical burntin sand tendency of the hypoeutectic gray cast iron. Due to the fact that the solidification process(from the surface to center) at primary austenite growth area in the lost-foam cylinder sample lags behind that in the green sand casting, the mushy solidification tendency of lost-foam casting is greater and the solidification time is longer.
基金Project(2006CB605203)supported by the National Basic Research Program of ChinaProject(2006AA03Z115)supported by the Hi-techResearch and Development Program of China
文摘A design of experiment technique was used to optimize the microstructure of the AZ91D alloy produced by rheo-casting. The experimental design consists of four parameters(pouring temperature,shearing temperature,shearing time and shearing rate) with three levels.The grain size and shape factor measurements of primaryα-Mg particles were conducted to determine the microstructure.The contribution of each parameter shows that pouring temperature is the most significant parameter affecting the grain size,and the shape factor highly depends on the shearing temperature.The optimized rheo-casting processing parameters are 650 C for pouring temperature,585℃for shearing temperature,40 s for shearing time,and 600 r/min for shearing rate.Under the optimized processing parameters,the average grain size is 28.53μm,and the shape factor is 0.591.
