Effects of VC/Cr3C2 on the microstructure and mechanical properties of Ti（C,N）-based cermets were studied. The microstructure was investigated by means of optical microscopy, X-ray diffractometry as well as scanning...Effects of VC/Cr3C2 on the microstructure and mechanical properties of Ti（C,N）-based cermets were studied. The microstructure was investigated by means of optical microscopy, X-ray diffractometry as well as scanning electron microscopy in combination with energy dispersive spectrometry. Mechanical properties, such as transverse rupture strength, hardness and fracture toughness, were measured. The results show that there are black core-grey rim structure and white core-grey rim structure in the microstructure. The grains become fine due to the VC/Cr3C2, and the grains of cermet added with 0.75VC/0.25Cr3C2 are refined most remarkably. The black core becomes finer with the increase of VC addition and rim phase becomes thicker with the decrease of Cr3C2 addition. The porosity increases with the increase of VC addition in VC/Cr3C2. Compared with the cermet free of VC/Cr3C2, the transverse rupture strength and hardness of cermets with VC/Cr3C2 are both improved, and the maximum values are both found for the cermet with 0.25VC/0.75Cr3C2. The fracture toughness can be effectively promoted by adding VC/Cr3C2 with an appropriate ratio of VC to Cr3C2, and the maximum value is found for the cermet with 0.5VC/0.5Cr3C2.展开更多
The effects of Mo on the microstructure and mechanical properties of Ti（C,N）-based cermets with low Ni have been studied systematically. Different contents of Mo （4-12 wt.%） were added into Tl（C,N）-based cermets...The effects of Mo on the microstructure and mechanical properties of Ti（C,N）-based cermets with low Ni have been studied systematically. Different contents of Mo （4-12 wt.%） were added into Tl（C,N）-based cermets. Specimens were fabricated by conventional powder metallurgy and vacuum sintered at temperatures of 1440, 1450, and 1460℃ individually. The microstructure and fracture morphology were investigated by scanning electron microscope, and the mechanical properties such as transverse strength and hardness were measured. The results show that the microstructure is uniform and the thickness of rim phase is moderate when the content of Mo is 8 wt.%; the mechanical properties of the specimens sintered at 1450℃ are better than those sintered at 1440 and 1460℃. The integrated properties of transverse strength and hardness are the best when the content of Mo is 8 wt.% and the sintering temperature is 1450℃.展开更多
The influence of raw powder particle size on the properties and microstructures of Ti (C, N)-based cermets has been studied. The conclusions are as follows: The microstructures of cermets were composed of two kinds of...The influence of raw powder particle size on the properties and microstructures of Ti (C, N)-based cermets has been studied. The conclusions are as follows: The microstructures of cermets were composed of two kinds of grains, the one with black cores surrounded by obvious rim structures, and the other whose cores were white with unconspicuous rim structures and adhesive phase. In the cermet made from fine powders, the amount of grains with white cores was much more than that in cermet made from coarse powders. In addition, their properties were also much better.展开更多
Firm joins were obtained between Ti(C,N)-based cermet and steel with Ag-Cu-Zn-Ni filler metal by vacuum brazing.The effects of technological parameters such as brazing temperature,holding time,and filler thickness on ...Firm joins were obtained between Ti(C,N)-based cermet and steel with Ag-Cu-Zn-Ni filler metal by vacuum brazing.The effects of technological parameters such as brazing temperature,holding time,and filler thickness on the shear strength of the joints were investigated.The microstructure of welded area and the reaction products of the filler metal were examined by scanning electron microscopy(SEM),metallographic microscope(OM),energy-dispersive X-ray analysis(EDS),and X-ray diffraction(XRD).The brazing temperature of 870℃,holding time of 15 min,and filler thickness of 0.4 mm are a set of optimum technological parameters,under which the maximum shear strength of the joints,176.5 MPa,is achieved.The results of microstructure show that the wettability of the filler metal on Ti(C,N)-based cermet and steel is well.A mutual solution layer and a diffusion layer exist between the welding base materials and the filler metal.展开更多
In this paper, Ti（C,N）-based nano cermets were prepared by nano particles, and the effect of VC addition on the micmstructure and properties of Ti（C,N）-based nano cermets was investigated. The results showed that ...In this paper, Ti（C,N）-based nano cermets were prepared by nano particles, and the effect of VC addition on the micmstructure and properties of Ti（C,N）-based nano cermets was investigated. The results showed that there existed black-core grayish-rim strucmre as well as gray-core grayish-rim structure in VC-doped Ti（C,N）-based nano cermets. With the increase of VC addition, the number of gray cores in- creased, the lattice parameter of Ti（C,N） phase increased, the grain size decreased, the hardness and fracture toughness of Ti（C,N）-based nano cermets were enhanced, and nearly full densification could be achieved. However, excessive addition of VC to 1 wt% resulted in slight decrease in hardness and fracture toughness. Some deep dimples were found in the fracture surface of cermets with VC addition, which corresponded to ductile fracture.展开更多
Ti（C, N）-based cermets were treated using hot isostatic pressing （HIP） at 1423 K in nitrogen. The microstructures compared with the as-sintered cermets were investigated using X-ray diffraction, scanning electron ...Ti（C, N）-based cermets were treated using hot isostatic pressing （HIP） at 1423 K in nitrogen. The microstructures compared with the as-sintered cermets were investigated using X-ray diffraction, scanning electron microscopy, transmission electron microscopy, energy-dispersive X-ray analysis, and electron microprobe analysis. It was found that high nitrogen activity in the surface zone resulted in the formation of gradient structure. Approximately 20-1am-deep, nitrogen-rich and titanium-rich hard surface zone was introduced by the heat treatment. The nitrogen activity was the driving force that caused the transportation of the atoms through the binder, titanium towards the surface, and tungsten and molybdenum inwards. In the surface zone, the particle size became fine, the inner rim disappeared, and the volume fraction of the outer rim and the binder phase considerably reduced. Small grains of TiN, WC, Mo2C, and nitrogen-rich carbonitlide phases formed in the surface zone during the heat treatment, improving the tlibological property of the heat-treated cermet.展开更多
The electrochemical corrosion behavior of Ti（C,N）-based cermets with different Mo2C additions was investigated in freely aerated 10% H2SO4 and potentiodynamic polarization of all the materials was conducted from -0....The electrochemical corrosion behavior of Ti（C,N）-based cermets with different Mo2C additions was investigated in freely aerated 10% H2SO4 and potentiodynamic polarization of all the materials was conducted from -0.5 to 1.5 V. There are two passive regions for all polarization curves. The first should be attributed to passive film formation due to Ti（C,N）, while the second may be due to the presence of Ni. Corrosion current density increases with M02C content increasing, from 2.06×10^-3 to 6.70×10^-3 mA/cm2. It is indicated that the corrosion resistance of Ti（C,N）-based cermets decreases with the increase of Mo2C addition. A skeleton of Ti（C,N） gains is observed after dissolution of Ni. The inner rim of cermets, rich in Mo2C, is corroded along with Ni binder and is more serious with the increase of Mo2C content. The secondary carbide Mo2C can be oxidized and dissolved in sulphuric acid.展开更多
Ultrafine Ti(C,N)-based cermet was sintered by SPS from 1050℃ to 1450℃ and its sintering properties,such as porosity,mechanical properties and phase transformation,were investigated by optical microscopy (OM),scanni...Ultrafine Ti(C,N)-based cermet was sintered by SPS from 1050℃ to 1450℃ and its sintering properties,such as porosity,mechanical properties and phase transformation,were investigated by optical microscopy (OM),scanning electron microscopy (SEM),X-ray diffraction (XRD),and differential scanning calorimeter (DSC).It is found that the spark plasma sintering properties of Ti(C,N)-based cermet differ from those of conventional vacuum sintering.The liquid phase appearance is at least lower by 150℃ than that in vacuum sintering.The porosity decreases sharply below 1 200℃ and reaches minimum at 1 200℃,and afterwards it almost keeps invariable and no longer increases.SPS remarkably accelerates the phase transformation of Ti(C,N)-based cermet and it has a powerful ability to remove oxides in Ti(C,N)-based cermets.Above 1 350℃,denitrification occurred.Fresh graphite phase formed above 1 430℃.Both the porosity and graphite are responsible for the poor TRS.展开更多
Spark plasma sintering(SPS)and conventional vacuum sintering(VS)wereemployed to fabricate ultrafine Ti(C,N)-based cermets.The shrinkage behavior,microstracture,andporosity and mechanical properties of the samples fabr...Spark plasma sintering(SPS)and conventional vacuum sintering(VS)wereemployed to fabricate ultrafine Ti(C,N)-based cermets.The shrinkage behavior,microstracture,andporosity and mechanical properties of the samples fabricated by SPS were compared with those of thesamples sintered by VS using optical microscopy,scanning electron microscopy,universal testingmachine,and rockwell tester.The results are as follows:(1)The shrinkage process occurred mainlyin the range of 1000-1300 deg C during the VS process,and only a 0.2 percent linear shrinkage ratioappeared below 800 deg C;during the SPS process,a 60 percent dimensional change occurred below800 deg C as a result of pressure action.(2)By utilizing the SPS technique,it is difficult forobtaining fully dense Ti(C,N)-based cermets.Due to the much existence of pores and un-combinedcarbon,the mechanical properties of the sintered samples by SPS are inferior to sintered ones byVS.(3)grain size of the samples sintered by SPS is still below 0.5 urn,but not by VS;because oflow sintering temperature,there are no typical core/rim structures formed in the sintered samplesby SPS1;the main microstructures of the sintered samples by SPS2 are a white core/grey shellstructure,whereas by VS show a typical black core/grey shell structure.展开更多
The high-temperature, high-pressure hot isostatic pressing technology was used for depositing hard coatings on Ti（C, N）-based cermets. The rnicrostructure and properties of the sample were investigated using optical...The high-temperature, high-pressure hot isostatic pressing technology was used for depositing hard coatings on Ti（C, N）-based cermets. The rnicrostructure and properties of the sample were investigated using optical microscopy, scan- ning electron microscopy, X-ray diffraction, electron probe microanalysis, and microhardness tester. The results showed that the rich titanium and nitrogen in surface zone were induced by the heat treatment. The high nitrogen activity of the surface region was the driving force for outward transport of titanium and inward transport of tungsten in the cobalt binder. The toughness and hardness were improved and a hardness gradient was formed. It is the high-temperature, high-pressure N2 that enables closure of holes, thereby alleviating defects and prolonging tool life.展开更多
The microstructure and mechanical properties of Ti(C, N)-based cermets with different content Mo were studied. Different Mo contents were added into Ti(C, N)-based cermets. Effect of sintering temperature on mechanica...The microstructure and mechanical properties of Ti(C, N)-based cermets with different content Mo were studied. Different Mo contents were added into Ti(C, N)-based cermets. Effect of sintering temperature on mechanical properties of the cermets was also investigated. Specimens were fabricated by conventional powder metallurgy techniques and vacuum sintered at different temperatures. The microstructure and the fracture morphology were investigated using scanning electron microscope. Transverse strength and hardness were measured. The results show that the microstructure is uniform and the thickness of rim phase is moderate when the content of Mo is 8%. The mechanical properties are the best when the content of Mo is 8% and the sintering temperature is 1450℃.展开更多
Effect of two-stage sintering parameters such as heating rate, top sintering temperature and holding time, sintering temperature and holding time at the second stage on relative density, transverse rupture strength(TR...Effect of two-stage sintering parameters such as heating rate, top sintering temperature and holding time, sintering temperature and holding time at the second stage on relative density, transverse rupture strength(TRS) and microstructures of powder injection molded Ti(C, N)-based cermets were investigated, by means of Archimedes’s method, three-point bending test and micrographic analysis. The results show that the optimum sintering cycle for powder injection molded Ti(C, N)-based cermets comprises rapid heating (10℃/min) at low temperatures, slow heating (5℃/min) at intermediate temperatures, holding at the highest sintering temperature (1420℃) for a short time (10min), and holding at the second stage (1360℃) for a longer time (6h) to avoid grain coarsening, and that its TRS reaches 624MPa, and there are little pores in their microstructures.展开更多
The availability using oxygen-rich powders to prepare ultrafine Ti(C,N)-based cermets was investigated. The deoxidation process, denitrification phenomenon and the effect of deoxidation on microstructure and mechanica...The availability using oxygen-rich powders to prepare ultrafine Ti(C,N)-based cermets was investigated. The deoxidation process, denitrification phenomenon and the effect of deoxidation on microstructure and mechanical properties of sintered samples were discussed, respectively. The results show that oxygen in the samples prepared even with high oxygen contained in starting powders can be almost completely cleaned away through suitable sintering process. The ultrafine oxygen-rich powders have a significant effect on microstructure, which promotes the formation of white core phase. A ultrafine Ti(C,N)-based cermet with mean particle size of 0. 30 μm, uniform microstructure and excellent mechanical properties is successfully prepared. It is also found that there exists severe denitrification phenomenon in the preparation process of ultrafine Ti(C,N)-based cermet.展开更多
In this paper,the author study the spectrum of high rank differential operators T (n) (t) of C 0 Semigroup T(t) ,given an approach to construct the spectral set opetator T (n) (t) ,and discussed the relat...In this paper,the author study the spectrum of high rank differential operators T (n) (t) of C 0 Semigroup T(t) ,given an approach to construct the spectral set opetator T (n) (t) ,and discussed the relation between the spectral points of both T (n) (t) and infinitesimal generator A of T(t) .展开更多
基金Project (090414185) supported by the Natural Science Foundation of Anhui Province, China
文摘Effects of VC/Cr3C2 on the microstructure and mechanical properties of Ti（C,N）-based cermets were studied. The microstructure was investigated by means of optical microscopy, X-ray diffractometry as well as scanning electron microscopy in combination with energy dispersive spectrometry. Mechanical properties, such as transverse rupture strength, hardness and fracture toughness, were measured. The results show that there are black core-grey rim structure and white core-grey rim structure in the microstructure. The grains become fine due to the VC/Cr3C2, and the grains of cermet added with 0.75VC/0.25Cr3C2 are refined most remarkably. The black core becomes finer with the increase of VC addition and rim phase becomes thicker with the decrease of Cr3C2 addition. The porosity increases with the increase of VC addition in VC/Cr3C2. Compared with the cermet free of VC/Cr3C2, the transverse rupture strength and hardness of cermets with VC/Cr3C2 are both improved, and the maximum values are both found for the cermet with 0.25VC/0.75Cr3C2. The fracture toughness can be effectively promoted by adding VC/Cr3C2 with an appropriate ratio of VC to Cr3C2, and the maximum value is found for the cermet with 0.5VC/0.5Cr3C2.
基金This work was financially supported by the National Natural Science Foundation of China (No. 50074017) the Natural Science Foundation of Hubei Province, China (No. 2003ABA092).
文摘The effects of Mo on the microstructure and mechanical properties of Ti（C,N）-based cermets with low Ni have been studied systematically. Different contents of Mo （4-12 wt.%） were added into Tl（C,N）-based cermets. Specimens were fabricated by conventional powder metallurgy and vacuum sintered at temperatures of 1440, 1450, and 1460℃ individually. The microstructure and fracture morphology were investigated by scanning electron microscope, and the mechanical properties such as transverse strength and hardness were measured. The results show that the microstructure is uniform and the thickness of rim phase is moderate when the content of Mo is 8 wt.%; the mechanical properties of the specimens sintered at 1450℃ are better than those sintered at 1440 and 1460℃. The integrated properties of transverse strength and hardness are the best when the content of Mo is 8 wt.% and the sintering temperature is 1450℃.
基金the National Natural Science Foundation of China, the Doctoral EducationFoundation of China, the State Key Laboratory of Powde
文摘The influence of raw powder particle size on the properties and microstructures of Ti (C, N)-based cermets has been studied. The conclusions are as follows: The microstructures of cermets were composed of two kinds of grains, the one with black cores surrounded by obvious rim structures, and the other whose cores were white with unconspicuous rim structures and adhesive phase. In the cermet made from fine powders, the amount of grains with white cores was much more than that in cermet made from coarse powders. In addition, their properties were also much better.
基金supported by the National Natural Science Foundation of China(No.50074014)
文摘Firm joins were obtained between Ti(C,N)-based cermet and steel with Ag-Cu-Zn-Ni filler metal by vacuum brazing.The effects of technological parameters such as brazing temperature,holding time,and filler thickness on the shear strength of the joints were investigated.The microstructure of welded area and the reaction products of the filler metal were examined by scanning electron microscopy(SEM),metallographic microscope(OM),energy-dispersive X-ray analysis(EDS),and X-ray diffraction(XRD).The brazing temperature of 870℃,holding time of 15 min,and filler thickness of 0.4 mm are a set of optimum technological parameters,under which the maximum shear strength of the joints,176.5 MPa,is achieved.The results of microstructure show that the wettability of the filler metal on Ti(C,N)-based cermet and steel is well.A mutual solution layer and a diffusion layer exist between the welding base materials and the filler metal.
基金financially supported by National Natural Science Foundation of China (No.50874076 and No.51074110)the Scientist Serving Enterprise Action Plan from Ministry of Science and Technology (No.2009GJF00030)
文摘In this paper, Ti（C,N）-based nano cermets were prepared by nano particles, and the effect of VC addition on the micmstructure and properties of Ti（C,N）-based nano cermets was investigated. The results showed that there existed black-core grayish-rim strucmre as well as gray-core grayish-rim structure in VC-doped Ti（C,N）-based nano cermets. With the increase of VC addition, the number of gray cores in- creased, the lattice parameter of Ti（C,N） phase increased, the grain size decreased, the hardness and fracture toughness of Ti（C,N）-based nano cermets were enhanced, and nearly full densification could be achieved. However, excessive addition of VC to 1 wt% resulted in slight decrease in hardness and fracture toughness. Some deep dimples were found in the fracture surface of cermets with VC addition, which corresponded to ductile fracture.
基金financially supported by the National Natural Science Foundation of China (Nos. 50074017 and 50104006)the Opening Fund of the Hubei Province Key Laboratory of Ceramics and Refractories of China (No. G0507)the Opening Fund of State Key Laboratory of Plastic Forming Simulation and Die & Mould Technology of China (No. 05-13)
文摘Ti（C, N）-based cermets were treated using hot isostatic pressing （HIP） at 1423 K in nitrogen. The microstructures compared with the as-sintered cermets were investigated using X-ray diffraction, scanning electron microscopy, transmission electron microscopy, energy-dispersive X-ray analysis, and electron microprobe analysis. It was found that high nitrogen activity in the surface zone resulted in the formation of gradient structure. Approximately 20-1am-deep, nitrogen-rich and titanium-rich hard surface zone was introduced by the heat treatment. The nitrogen activity was the driving force that caused the transportation of the atoms through the binder, titanium towards the surface, and tungsten and molybdenum inwards. In the surface zone, the particle size became fine, the inner rim disappeared, and the volume fraction of the outer rim and the binder phase considerably reduced. Small grains of TiN, WC, Mo2C, and nitrogen-rich carbonitlide phases formed in the surface zone during the heat treatment, improving the tlibological property of the heat-treated cermet.
基金Project(51074110) supported by the National Natural Science Foundation of ChinaProject(10GGZD080GX-268) supported by Chengdu Science and Technology Program, China
文摘The electrochemical corrosion behavior of Ti（C,N）-based cermets with different Mo2C additions was investigated in freely aerated 10% H2SO4 and potentiodynamic polarization of all the materials was conducted from -0.5 to 1.5 V. There are two passive regions for all polarization curves. The first should be attributed to passive film formation due to Ti（C,N）, while the second may be due to the presence of Ni. Corrosion current density increases with M02C content increasing, from 2.06×10^-3 to 6.70×10^-3 mA/cm2. It is indicated that the corrosion resistance of Ti（C,N）-based cermets decreases with the increase of Mo2C addition. A skeleton of Ti（C,N） gains is observed after dissolution of Ni. The inner rim of cermets, rich in Mo2C, is corroded along with Ni binder and is more serious with the increase of Mo2C content. The secondary carbide Mo2C can be oxidized and dissolved in sulphuric acid.
基金FundedbytheNationalNaturalScienceFoundationofChi na (No .5 0 0 74 0 17)andStateKeyLaboratoryofAdvancedTechnol ogyforMaterialsSynthesisandProcessingofWuhanUniversityofTechnology
文摘Ultrafine Ti(C,N)-based cermet was sintered by SPS from 1050℃ to 1450℃ and its sintering properties,such as porosity,mechanical properties and phase transformation,were investigated by optical microscopy (OM),scanning electron microscopy (SEM),X-ray diffraction (XRD),and differential scanning calorimeter (DSC).It is found that the spark plasma sintering properties of Ti(C,N)-based cermet differ from those of conventional vacuum sintering.The liquid phase appearance is at least lower by 150℃ than that in vacuum sintering.The porosity decreases sharply below 1 200℃ and reaches minimum at 1 200℃,and afterwards it almost keeps invariable and no longer increases.SPS remarkably accelerates the phase transformation of Ti(C,N)-based cermet and it has a powerful ability to remove oxides in Ti(C,N)-based cermets.Above 1 350℃,denitrification occurred.Fresh graphite phase formed above 1 430℃.Both the porosity and graphite are responsible for the poor TRS.
基金supported by the National Natural Science Foundation of China(No.50074017)the Natural Sci-ence Foundation of Hubei Province(No.2003ABA092)the Doctoral Education Fundation of China(No.1999048714).
文摘Spark plasma sintering(SPS)and conventional vacuum sintering(VS)wereemployed to fabricate ultrafine Ti(C,N)-based cermets.The shrinkage behavior,microstracture,andporosity and mechanical properties of the samples fabricated by SPS were compared with those of thesamples sintered by VS using optical microscopy,scanning electron microscopy,universal testingmachine,and rockwell tester.The results are as follows:(1)The shrinkage process occurred mainlyin the range of 1000-1300 deg C during the VS process,and only a 0.2 percent linear shrinkage ratioappeared below 800 deg C;during the SPS process,a 60 percent dimensional change occurred below800 deg C as a result of pressure action.(2)By utilizing the SPS technique,it is difficult forobtaining fully dense Ti(C,N)-based cermets.Due to the much existence of pores and un-combinedcarbon,the mechanical properties of the sintered samples by SPS are inferior to sintered ones byVS.(3)grain size of the samples sintered by SPS is still below 0.5 urn,but not by VS;because oflow sintering temperature,there are no typical core/rim structures formed in the sintered samplesby SPS1;the main microstructures of the sintered samples by SPS2 are a white core/grey shellstructure,whereas by VS show a typical black core/grey shell structure.
基金This work was financially supported by the Natural Science Foundation of Hubei Province (No. 2003ABA092) and the Natural Science Foundation of China (No.50074014).
文摘The high-temperature, high-pressure hot isostatic pressing technology was used for depositing hard coatings on Ti（C, N）-based cermets. The rnicrostructure and properties of the sample were investigated using optical microscopy, scan- ning electron microscopy, X-ray diffraction, electron probe microanalysis, and microhardness tester. The results showed that the rich titanium and nitrogen in surface zone were induced by the heat treatment. The high nitrogen activity of the surface region was the driving force for outward transport of titanium and inward transport of tungsten in the cobalt binder. The toughness and hardness were improved and a hardness gradient was formed. It is the high-temperature, high-pressure N2 that enables closure of holes, thereby alleviating defects and prolonging tool life.
文摘The microstructure and mechanical properties of Ti(C, N)-based cermets with different content Mo were studied. Different Mo contents were added into Ti(C, N)-based cermets. Effect of sintering temperature on mechanical properties of the cermets was also investigated. Specimens were fabricated by conventional powder metallurgy techniques and vacuum sintered at different temperatures. The microstructure and the fracture morphology were investigated using scanning electron microscope. Transverse strength and hardness were measured. The results show that the microstructure is uniform and the thickness of rim phase is moderate when the content of Mo is 8%. The mechanical properties are the best when the content of Mo is 8% and the sintering temperature is 1450℃.
文摘Effect of two-stage sintering parameters such as heating rate, top sintering temperature and holding time, sintering temperature and holding time at the second stage on relative density, transverse rupture strength(TRS) and microstructures of powder injection molded Ti(C, N)-based cermets were investigated, by means of Archimedes’s method, three-point bending test and micrographic analysis. The results show that the optimum sintering cycle for powder injection molded Ti(C, N)-based cermets comprises rapid heating (10℃/min) at low temperatures, slow heating (5℃/min) at intermediate temperatures, holding at the highest sintering temperature (1420℃) for a short time (10min), and holding at the second stage (1360℃) for a longer time (6h) to avoid grain coarsening, and that its TRS reaches 624MPa, and there are little pores in their microstructures.
基金Project(50323008) supported by the National Natural Science Foundation of China
文摘The availability using oxygen-rich powders to prepare ultrafine Ti(C,N)-based cermets was investigated. The deoxidation process, denitrification phenomenon and the effect of deoxidation on microstructure and mechanical properties of sintered samples were discussed, respectively. The results show that oxygen in the samples prepared even with high oxygen contained in starting powders can be almost completely cleaned away through suitable sintering process. The ultrafine oxygen-rich powders have a significant effect on microstructure, which promotes the formation of white core phase. A ultrafine Ti(C,N)-based cermet with mean particle size of 0. 30 μm, uniform microstructure and excellent mechanical properties is successfully prepared. It is also found that there exists severe denitrification phenomenon in the preparation process of ultrafine Ti(C,N)-based cermet.
文摘In this paper,the author study the spectrum of high rank differential operators T (n) (t) of C 0 Semigroup T(t) ,given an approach to construct the spectral set opetator T (n) (t) ,and discussed the relation between the spectral points of both T (n) (t) and infinitesimal generator A of T(t) .
