With the rapid development of wireless techniques,the bandpass filter(BPF)is required to cover microwave and millimeter-wave frequency bands simultaneously with good mid-band suppression.However,it is difficult to imp...With the rapid development of wireless techniques,the bandpass filter(BPF)is required to cover microwave and millimeter-wave frequency bands simultaneously with good mid-band suppression.However,it is difficult to implement such BPF due to the large frequency ratio and wideband rejection.This paper presents a superior method to realize a dual-band BPF with a large frequency ratio maintaining compact size and low design complexity.This is contributed by an ultra-wide stopband BPF with inherent discriminating excited degree at spurious frequencies.By properly arranging the feeding position and electrical length ratio of stepped impedance resonator(SIR),the excited degree at specific spurious frequencies can be flexibly adjusted to achieve desired suppression level without affecting characteristics at the fundamental passband.For validation,two BPFs were simulated,fabricated and measured,exhibiting suppression levels of 20.3 dB and 35 dB up to 18f0 and 10.53f0 respectively.Based on this,a dual-band BPF with a large frequency ratio can be easily constructed.For demonstration,a dual-band BPF operating at 3.55 GHz and 43.15 GHz is implemented.A frequency ratio up to 12.15 and mid-band suppression level better than 28 dB had been achieved.Advantages of compactness,simplicity and excellent performance of the proposed work can be observed.展开更多
Design of a miniaturized lumped-element bandpass filter in multilayer liquid crystal polymer technology is proposed.Fractional bandwidth of the bandpass filter is 20%,operating at a center frequency of 500 MHz.In orde...Design of a miniaturized lumped-element bandpass filter in multilayer liquid crystal polymer technology is proposed.Fractional bandwidth of the bandpass filter is 20%,operating at a center frequency of 500 MHz.In order to further reduce the size and improve the performance of the proposed filter,defected ground structure(DGS)has been implemented in the filter.Based on this structure,the volume of the inductor is reduced by 60%eficiently compared with the inductor without DGS,and the Q-factor is increased up to 257%compared with the traditional multilayer spiral inductor.The measured results indicate that the designed filter has a very sharp stopband,an insertion loss of 2.3dB,and a return loss of 18.6dB in the passband.The whole volume of the fabricated filter is 0.032入_(g)×0.05入_(g)×0.00075入_(g),where Ag is the guided wavelength of the center frequency.The proposed filter is easily integrated into radio-frequency/microwave circuitry at a low manufacturing cost,especially wireless communication.展开更多
In this paper,a compact defected ground structure loaded ultra high frequency dual-band bandpass flter is designed and implemented based on multilayer liquid crystal polymer technology.This novel filter is simply comp...In this paper,a compact defected ground structure loaded ultra high frequency dual-band bandpass flter is designed and implemented based on multilayer liquid crystal polymer technology.This novel filter is simply composed with several lumped and semi-lumped elements,to create a dual-passband response.In order to enhance the out-of-band rejection,a feedback capacitor C_(z) at the in/out ports of the filter is introduced,and four transmission zeros(TZs)are obtained outside the pass band.Furthermore,the position of TZs can be determined by adjusting the value of C_(z).The schematic and design process of the filter are given in this paper.The center frequencies of dual-band bandpass filter are 0.9 GHz and 2.45 GHz,and the 3-dB bandwidths are 13.7%and 14.3%,respectively.The circuit size is 11 mm×9.5 mm×0.193 mm.The proposed filter has been fabricated and tested,and the measured result is in good agreement with the simulation result.展开更多
The microstrip dual-mode filter （DMF） with conventional coupling structure has some limitations in- eluding the port coupling strength limited by fabrication tolerance and the existence of serious second order spuri...The microstrip dual-mode filter （DMF） with conventional coupling structure has some limitations in- eluding the port coupling strength limited by fabrication tolerance and the existence of serious second order spuri- ous band. Therefore, a novel DMF with a offset-feed bended coupling structure and a stepped-impedance dual- mode resonator is proposed for coupling enhancement and spurious response suppression. Based on the analysis of the change of spur frequencies and the current distribution of spur resonant modes, all spurs near passband of the cascaded DMF can be fully suppressed by optimizing the structure parameters of parasite resonators, which bene- fits from the inherent well-controlled transmission zeros. Experimental results show that the proposed DMF ex- hibits lower insertion loss ,much sharper rate of cutoff and wider spur-free stop band compared with conventional DMF. This design is applicable for spur suppression in wideband communication.展开更多
A design of a linear and fully-balanced operational transconductanee amplifier （OTA） with improved high DC gain and wide bandwidth is presented. Derivative from a single common-source field effect transistor （FET）...A design of a linear and fully-balanced operational transconductanee amplifier （OTA） with improved high DC gain and wide bandwidth is presented. Derivative from a single common-source field effect transistor （FET） cas- cade and its DC I-V characteristics,the third-order coefficient g3 hasbeen well compensated with a parallel FET operated in the triode region, which has even-odd symmetries between the boundary of the saturation and triode region. Therefore,for high linearity,a simple solution is obtained to increase input signal amplitude in saturation for the application of OTA continuous-time filters. A negative resistance load （NRL） technique is used for the compensation of parasitic output resistance and an achievement of a high DC-gain of the OTA circuits without extra internal nodes. Additionally, derivations from the ideal -90° phase of the gm-C integrator mainly due to a finite DC gain and parasitic poles will be avoided in the frequency range of interest. HSPICE simulation shows that the total harmonic distortion at 1Vp-p is less than 1% from a single 3.3V supply. As an application of the VHF CMOS OTA,a second-order OTA-C bandpass filter is fabricated using a 0. 18μm CMOS process with two kinds of gate-oxide layers, which has achieved a center frequency of 20MHz,a 3dB-bandwidth of 180kHz,and a quality factor of 110.展开更多
We report the design of a novel multiband metamaterial bandpass filter （BPF） in the terahertz （THz）-wave region. The designed BPF is composed of a metal-dielectric-metal sandwiched structure with three nested ring...We report the design of a novel multiband metamaterial bandpass filter （BPF） in the terahertz （THz）-wave region. The designed BPF is composed of a metal-dielectric-metal sandwiched structure with three nested rings on the top surface and a cross structure on the bottom surface. Full-wave simulation results show that the designed BPF has three transmission peaks at frequencies of 0.42, 1.27, and 1.86 THz with transmission rates of-0.87,-1.85, and-1.83 dB, respectively. Multi-reflection interference theory is introduced to explain the transmission mechanism of the designed triple-band BPF. The theoretical transmission spectrum is in good agreement with the full-wave simulated results. The designed BPF can maintain a stable performance as the incident angle varies from 0 to 30 for both transverse electric and transverse magnetic polarizations of the incident wave. The designed BPF can be potentially used in THz devices due to its multiband transmissions, polarization insensitivity, and stable wide-angle response in the THz region.展开更多
We investigate the guiding modes of spoof surface plasmon polaritons （SPPs） on a symmetric ultra-thin plasmonic structure. From the analysis, we deduce the operating frequency region of the single-mode propagation. ...We investigate the guiding modes of spoof surface plasmon polaritons （SPPs） on a symmetric ultra-thin plasmonic structure. From the analysis, we deduce the operating frequency region of the single-mode propagation. Based on this property, a spoof SPPs lowpass filter is then constituted in the microwave frequency. By introducing a transmission zero at the lower frequency band using a pair of stepped-impedance stubs, a wide passband filter is further realized. The proposed filter is fed by.a transducer composed of a microstrip line with a flaring ground. The simulated results show that the presented filter has an extremely wide upper stopband in addition to excellent passband filtering characteristics such as low loss, wide band, and high square ratio. A prototype passband filter is also fabricated to validate the predicted performances. The proposed spoof-SPPs filter is believed to be very promising for other surface waveguide components in microwave and terahertz bands.展开更多
In this paper,a 5G wideband power amplifier(PA)with bandpass filtering response is synthesized using a bandwidth-extended bandpass filter as the matching network(MN).In this structure,the bandwidth(θ_(C))is defined a...In this paper,a 5G wideband power amplifier(PA)with bandpass filtering response is synthesized using a bandwidth-extended bandpass filter as the matching network(MN).In this structure,the bandwidth(θ_(C))is defined as a variable in the closedform equations provided by the microstrip bandpass filter.It can be extended over a wide range only by changing the characteristic impedances of the structure.Different from the other wideband MNs,the extension of bandwidth does not increase the complexity of the structure(order n is fixed).In addition,based on the bandwidth-extended structure,the wideband design of bandpass filtering PA is not limited to the fixed bandwidth of the specific filter structure.The theoretical analysis of the MN and the design flow of the PA are provided in this design.The fabricated bandpass filtering PA can support almost one-octave bandwidth(2-3.8 GHz),covering the two 5G bands(n41 and n78).The drain efficiency of 47%-60%and output power higher than 40 dBm are measured.Good frequency selectivity in S-parameter measurements can be observed.展开更多
A tunable microwave photonic bandpass filter with high mainlobe-to-sidelobe ratio (MSR) based on a phase modulator and a dispersive device is proposed. The multi-tap characteristics of the filter are realized by slici...A tunable microwave photonic bandpass filter with high mainlobe-to-sidelobe ratio (MSR) based on a phase modulator and a dispersive device is proposed. The multi-tap characteristics of the filter are realized by slicing a broadband source using a Mach-Zehnder interferometer (MZI) which results in a high MSR of 25 dB. The tunability of the filter is realized by an optical variable delay line (OVDL) in one arm of the MZI, which changes the wavelength spacing of the sliced broadband source and results in a tunable free spectrum range (FSR) of the filter. The central frequency of the bandpass filter is tunable from 10.7 GHz to 27 GHz by changing the wavelength spacing from 0.145 nm to 0.054 nm.展开更多
In this paper, the variational method combined with Green's function is used to analyze the characteristics of suspended, stripline. The result is in good agreement with references. The design of mm-wave end-coupl...In this paper, the variational method combined with Green's function is used to analyze the characteristics of suspended, stripline. The result is in good agreement with references. The design of mm-wave end-coupled bandpass filter with suspended substrate is discussed. The computer programs for design of suspended stripline and bandpass filter are established.展开更多
A novel bandpass filter(BPF)based on spoof surface plasmon polaritons(SSPPs)using a compact folded slotline structure is proposed and experimentally demonstrated.The proposed novel SSPPs structure compared with a conv...A novel bandpass filter(BPF)based on spoof surface plasmon polaritons(SSPPs)using a compact folded slotline structure is proposed and experimentally demonstrated.The proposed novel SSPPs structure compared with a conventional plasmonic waveguide with slot line SSPPs unit structure at the same size,the considerable advantages in much lower asymptotic frequency with tight field confinement,which enable the proposed filter to be more miniaturization.A high-efficient mode conversion structure is designed to transition from TE-mode to SSPPs-mode by gradient slotline lengths.The low-frequency stop-band can be committed with microstrip to slotline evolution on both sides of the dielectric,while the high-frequency cutoff band is realized by the proposed SSPPs structure.The influence of dispersion relation,electric field distribution,surface current,and structural parameters on the transmission characteristics of the proposed BPF are analyzed by finite difference time domain(FDTD).To validate the design concept,the prototype of the miniaturized SSPPs BPF has been manufactured and measured.The experimental results show high performance of the fabricated sample,in which the working in a range of 0.9 GHz-5.2 GHz with the relative bandwidth is 142%,the insertion loss less than 0.5 dB,the reflection coefficient less than-10 dB,and the group delay is less than one ns.This works provides a mirror for realizing the miniaturization of waveguides,and the application and development of high-confinement SSPPs functional devices in the microwave and THz regimes.展开更多
This study is concerned with the diagnosis of discrepancies in a steel truss bridge by identifying dynamic properties from the vibration response signals of the bridges.The vibration response signals collected at brid...This study is concerned with the diagnosis of discrepancies in a steel truss bridge by identifying dynamic properties from the vibration response signals of the bridges.The vibration response signals collected at bridges under three different vehicular speeds of 10 km/hr,20 km/hr,and 30 km/hr are analyzed using statistical features such as kurtosis,magnitude of peak-to-peak,root mean square,crest factor as well as impulse factor in time domain,and Stockwell transform in the time-frequency domain.The considered statistical features except for kurtosis show uncertain behavior.The Stockwell transform showed low-resolution outcomes when the presence of noise in the recorded vibration responses.The elimination of noise and extraction of meaningful dynamic properties from the vibration responses is done by applying a new method which comes from the fusion of Hilbert transform with Spectral kurtosis and bandpass filtering.The outcomes obtained from Hilbert transform processed residual signals which are further filtered using bandpass filter show more robustness and accuracy in characterizing bridge modal frequencies from the noisy vibration responses.The proposed method produces a high-resolution frequency response which can unveil the joint discrepancy in the bridge structure.展开更多
In this study, we propose a novel resonator that is composed of a modified spiral with an embedded interdigital capacitor. A large ratio of the first spurious frequency to the fundamental resonant frequency is obtaine...In this study, we propose a novel resonator that is composed of a modified spiral with an embedded interdigital capacitor. A large ratio of the first spurious frequency to the fundamental resonant frequency is obtained, which is suitable for the design of filters with wide stopbands, and the circuit size is considerably reduced by embedding the interdigital structure in the spiral. For demonstration, a compact four-pole high temperature superconducting（HTS） filter with a center frequency of 568 MHz is designed and fabricated on double-sided YBCO film with a size of 11.4 mm×8.0 mm. The filter measurement shows excellent performance with an out-of-band rejection level better than 60.9 dB up to 3863 MHz.展开更多
Modern electronic circuit requires compact,multifunctional technology in communication systems.However,it is very difficult due to the limitations in passive component miniaturization and the complication of fabricati...Modern electronic circuit requires compact,multifunctional technology in communication systems.However,it is very difficult due to the limitations in passive component miniaturization and the complication of fabrication process.The bandpass filter is one of the most important passive components in millimeter（mm）-wave communication system,attracting significant interest in three-dimension（3D） miniaturized design,which is few reported.In this paper,a bandpass filter structure using low-temperature co-fired ceramic（LTCC） technology,which is fully integrated in a system-in package（SIP） communication module,is presented for miniaturized and high reliable mm-wave application.The bandpass filter with 3D end-coupled microstrip resonators is implemented in order to achieve a high performance bandwidth characteristic.Specifically,all of the resonators are embedded into different ceramic layers to decrease the insertion loss and enhance the out-of-band rejection performance by optimizing the coupling coefficient and the coupling strength.A fence structure,which is formed by metal-filled via array with the gap less than quarter wavelength,is placed around the embedded bandpass filter to avoid electromagnetic（EM） interference problem in multilayer structure.This structural model is validated through actual LTCC process.The bandpass filter is successfully manufactured by modifying the co-fireablity characteristics,adjusting the sintering profile,releasing the interfacial stress,and reducing the shrinkage mismatch with different materials.Measured results show good performance and agree well with the high frequency EM full wave simulation.The influence of layer thickness and dielectric constant on the frequency response in fabricated process is analyzed,where thicker ceramic sheets let the filter response shift to higher frequency.Moreover,measured S-parameters denote the center frequency is also strongly influenced by the variation of ceramic material＇s dielectric constants.By analyzing the relationship between the characteristics of the ceramic tape and the center frequency of the filter,both theoretical and experimental data are accumulated for broadening application filed.With the coupling resonators embedded into the ceramic layers,the bandpass filter exhibits advantages of small size and high reliability compared to conventional planar filter structure,which makes the bandpass filter suitable for SIP communicational application.展开更多
A prototype IIR bandpass filter is derived from an analog bandpass filter using bilinear transformation. The formulas relating the IIR bandpass filter's coefficients with its centre frequency and bandwidth are obt...A prototype IIR bandpass filter is derived from an analog bandpass filter using bilinear transformation. The formulas relating the IIR bandpass filter's coefficients with its centre frequency and bandwidth are obtained. Using N sections of such filters, a cascade IIR bandpass filter is constructed. Based on given specifications and the formulas, the parameter N and the bandwidth of prototype filter can be obtained, and the required cascade IIR bandpass filter is obtained. The filter has a small set of coefficients with a simple structure, therefore is easy to design. The described approach is especially suitable for hardware implementation.展开更多
We propose a compact dual-band bandpass filter(BPF)based on one-dimensional porous silicon(PS)photonic crystal by electrochemical etching.By inserting three periods of high and low reflective index layers in the cente...We propose a compact dual-band bandpass filter(BPF)based on one-dimensional porous silicon(PS)photonic crystal by electrochemical etching.By inserting three periods of high and low reflective index layers in the center of porous silicon microcavity(PSM),two sharp resonant peaks appear in the high reflectivity stop band on both sides of the resonance wavelength.Through simulation and experiment,the physical mechanisms of the two resonance peaks and the resonance wavelength are also studied.It is found that the resonance wavelength can be tuned only by adjusting the effective optical thickness(EOT)of each PS layer,in which different resonance wavelengths have different widths between the two sharp resonance peaks.Besides,the analysis indicates that oxidization makes the blue shift become larger for high wavelength than that for low wavelength.Such a fabricated BPF based on PS dual-microcavity is easy to be fabricated and low cost,which benefits the application of integrated optical devices.展开更多
An ultra-wideband bandpass filter(BPF)with a wide out-of-band rejection based on a surface plasmonic waveguide(SPW)slotline with ring grooves is designed and analyzed.A paired microstrip-to-slotline transition is desi...An ultra-wideband bandpass filter(BPF)with a wide out-of-band rejection based on a surface plasmonic waveguide(SPW)slotline with ring grooves is designed and analyzed.A paired microstrip-to-slotline transition is designed for quasiTEM to TM mode conversion by using a microstrip line with a circular pad and the slotline with the same circular slot.The mode conversion between the TM and the surface plasmon polariton(SPP)mode is realized by using a gradient slotline with ring grooves and an impedance matching technique.The upper cut-off frequencies of the passband can be adjusted by using these proposed SPP units,while the lower frequencies of the passband are created by using the microstrip-toslotline transitions to give an ultra-wideband BPF.The dispersion curves of SPP units,electric field distribution,and the transmission spectra of the proposed ultra-wideband bandpass filter are all calculated and analyzed by the finite-difference time-domain(FDTD)method.The simulated results show that the presented filter has good performance including a wide3-dB bandwidth of 149%from 0.57 GHz to 3.93 GHz,an extremely wide 40-dB upper-band rejection from 4.2 GHz to18.5 GHz,and low loss and high selectivity in the passband.To prove the design validity,a prototype of the BPF has been manufactured and measured,showing a reasonable agreement with simulation results.The unique features of the proposed BPF may make it applicable for integrated circuit and plasmonic devices in microwave or THz frequency ranges.展开更多
In this paper, the resonant frequency of a dual\|mode dielectric resonator is calculated using a finite difference time\|domain method. A new type of bandpass filter is designed with the calculated coupling coefficien...In this paper, the resonant frequency of a dual\|mode dielectric resonator is calculated using a finite difference time\|domain method. A new type of bandpass filter is designed with the calculated coupling coefficient. The filter designed in this paper has reached the design goal, verified by simulation with Ansoft HFSS.展开更多
A high performance Balun BandPass Filter (BPF) with capacitively loaded multiple coupled lines with very simple structure is proposed in this paper, this structure realizes simultaneous size reduction and superior har...A high performance Balun BandPass Filter (BPF) with capacitively loaded multiple coupled lines with very simple structure is proposed in this paper, this structure realizes simultaneous size reduction and superior harmonic response suppression performance in bandpass filtering meanwhile good differential performance of the Balun. The theory of this structure for unbalanced input into balanced output has been studied in this paper and a proper Balun and BPF characteristic by the symmetric feeding and skew symmetric feeding have been obtained to prove the theory. The enter frequency of the fabricated Balun-BPF is operated at 2.45 GHz with 6.93% Fractional Band Width (FBW), and this frequency is used for Bluetooth and some other communication systems. The differences between the two outputs are 180°± 1.92° in phase and within 0.33 dB in magnitude. At f0, the amplitude imbalance and phase difference are within 0.25 dB and 180.86°, respectively. The measured frequency responses agree well with the simulated ones. With the theoretical analyses and practical results, it is shown that the proposed one has the advantages of simple structure, convenient analysis and good performance of both BPF and Balun.展开更多
In this paper,a Slotted Stepped-Impedance Resonator (SSIR) is proposed.Due to the slots in the low-impedance section of the conventional SIR,the new resonator has a lower fundamental resonance f0 and can provide a pot...In this paper,a Slotted Stepped-Impedance Resonator (SSIR) is proposed.Due to the slots in the low-impedance section of the conventional SIR,the new resonator has a lower fundamental resonance f0 and can provide a potential finite transmission zero fz close to f0.Based on the proposed SSIR,a fourth-order Chebychev BandPass Filter (BPF) is designed at f0=1 GHz.The measured results show that a better than-65 dB rejection is achieved on both the lower and the upper stopband.Moreover,the new filter has a wide-30 dB rejection upper stopband from 1.13f0 to 6.52f0.The fabricated filter exhibits a size of The new filter has a planar topology and is easily integrated with modern portable communication systems.展开更多
基金supported by the National Natural Science Foundation of China(No.61671485).
文摘With the rapid development of wireless techniques,the bandpass filter(BPF)is required to cover microwave and millimeter-wave frequency bands simultaneously with good mid-band suppression.However,it is difficult to implement such BPF due to the large frequency ratio and wideband rejection.This paper presents a superior method to realize a dual-band BPF with a large frequency ratio maintaining compact size and low design complexity.This is contributed by an ultra-wide stopband BPF with inherent discriminating excited degree at spurious frequencies.By properly arranging the feeding position and electrical length ratio of stepped impedance resonator(SIR),the excited degree at specific spurious frequencies can be flexibly adjusted to achieve desired suppression level without affecting characteristics at the fundamental passband.For validation,two BPFs were simulated,fabricated and measured,exhibiting suppression levels of 20.3 dB and 35 dB up to 18f0 and 10.53f0 respectively.Based on this,a dual-band BPF with a large frequency ratio can be easily constructed.For demonstration,a dual-band BPF operating at 3.55 GHz and 43.15 GHz is implemented.A frequency ratio up to 12.15 and mid-band suppression level better than 28 dB had been achieved.Advantages of compactness,simplicity and excellent performance of the proposed work can be observed.
基金the Shaanxi Provincial Key Research and Development Program(No.2020GY-040)。
文摘Design of a miniaturized lumped-element bandpass filter in multilayer liquid crystal polymer technology is proposed.Fractional bandwidth of the bandpass filter is 20%,operating at a center frequency of 500 MHz.In order to further reduce the size and improve the performance of the proposed filter,defected ground structure(DGS)has been implemented in the filter.Based on this structure,the volume of the inductor is reduced by 60%eficiently compared with the inductor without DGS,and the Q-factor is increased up to 257%compared with the traditional multilayer spiral inductor.The measured results indicate that the designed filter has a very sharp stopband,an insertion loss of 2.3dB,and a return loss of 18.6dB in the passband.The whole volume of the fabricated filter is 0.032入_(g)×0.05入_(g)×0.00075入_(g),where Ag is the guided wavelength of the center frequency.The proposed filter is easily integrated into radio-frequency/microwave circuitry at a low manufacturing cost,especially wireless communication.
基金the Shaanxi Provincial Innovation Team Project(No.2020TD-019)the Xi'an Sciences Plan Project(No.2021XJZZ0075)。
文摘In this paper,a compact defected ground structure loaded ultra high frequency dual-band bandpass flter is designed and implemented based on multilayer liquid crystal polymer technology.This novel filter is simply composed with several lumped and semi-lumped elements,to create a dual-passband response.In order to enhance the out-of-band rejection,a feedback capacitor C_(z) at the in/out ports of the filter is introduced,and four transmission zeros(TZs)are obtained outside the pass band.Furthermore,the position of TZs can be determined by adjusting the value of C_(z).The schematic and design process of the filter are given in this paper.The center frequencies of dual-band bandpass filter are 0.9 GHz and 2.45 GHz,and the 3-dB bandwidths are 13.7%and 14.3%,respectively.The circuit size is 11 mm×9.5 mm×0.193 mm.The proposed filter has been fabricated and tested,and the measured result is in good agreement with the simulation result.
基金Supported by the National Natural Science Foundation of China under Grant(60921063)the National Program on Key Basic Research Project(973Program)(2010CB327400)the National Science and Technology Major Project(2010ZX03007-002-01)~~
文摘The microstrip dual-mode filter （DMF） with conventional coupling structure has some limitations in- eluding the port coupling strength limited by fabrication tolerance and the existence of serious second order spuri- ous band. Therefore, a novel DMF with a offset-feed bended coupling structure and a stepped-impedance dual- mode resonator is proposed for coupling enhancement and spurious response suppression. Based on the analysis of the change of spur frequencies and the current distribution of spur resonant modes, all spurs near passband of the cascaded DMF can be fully suppressed by optimizing the structure parameters of parasite resonators, which bene- fits from the inherent well-controlled transmission zeros. Experimental results show that the proposed DMF ex- hibits lower insertion loss ,much sharper rate of cutoff and wider spur-free stop band compared with conventional DMF. This design is applicable for spur suppression in wideband communication.
文摘A design of a linear and fully-balanced operational transconductanee amplifier （OTA） with improved high DC gain and wide bandwidth is presented. Derivative from a single common-source field effect transistor （FET） cas- cade and its DC I-V characteristics,the third-order coefficient g3 hasbeen well compensated with a parallel FET operated in the triode region, which has even-odd symmetries between the boundary of the saturation and triode region. Therefore,for high linearity,a simple solution is obtained to increase input signal amplitude in saturation for the application of OTA continuous-time filters. A negative resistance load （NRL） technique is used for the compensation of parasitic output resistance and an achievement of a high DC-gain of the OTA circuits without extra internal nodes. Additionally, derivations from the ideal -90° phase of the gm-C integrator mainly due to a finite DC gain and parasitic poles will be avoided in the frequency range of interest. HSPICE simulation shows that the total harmonic distortion at 1Vp-p is less than 1% from a single 3.3V supply. As an application of the VHF CMOS OTA,a second-order OTA-C bandpass filter is fabricated using a 0. 18μm CMOS process with two kinds of gate-oxide layers, which has achieved a center frequency of 20MHz,a 3dB-bandwidth of 180kHz,and a quality factor of 110.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.11504418,11447033,and 61372048)the Fundamental Research Funds for the Central Universities,China(Grant No.2015XKMS075)
文摘We report the design of a novel multiband metamaterial bandpass filter （BPF） in the terahertz （THz）-wave region. The designed BPF is composed of a metal-dielectric-metal sandwiched structure with three nested rings on the top surface and a cross structure on the bottom surface. Full-wave simulation results show that the designed BPF has three transmission peaks at frequencies of 0.42, 1.27, and 1.86 THz with transmission rates of-0.87,-1.85, and-1.83 dB, respectively. Multi-reflection interference theory is introduced to explain the transmission mechanism of the designed triple-band BPF. The theoretical transmission spectrum is in good agreement with the full-wave simulated results. The designed BPF can maintain a stable performance as the incident angle varies from 0 to 30 for both transverse electric and transverse magnetic polarizations of the incident wave. The designed BPF can be potentially used in THz devices due to its multiband transmissions, polarization insensitivity, and stable wide-angle response in the THz region.
基金Project supported by the Key Grant Project of Ministry of Education of China(Grant No.313029)the FDCT Research Grant from Macao Science and Technology Development Fund,China(Grant No.051/2014/A1)the Multi-Year Research Grant from University of Macao,Macao SAR,China(Grant No.MYRG2014-00079-FST)
文摘We investigate the guiding modes of spoof surface plasmon polaritons （SPPs） on a symmetric ultra-thin plasmonic structure. From the analysis, we deduce the operating frequency region of the single-mode propagation. Based on this property, a spoof SPPs lowpass filter is then constituted in the microwave frequency. By introducing a transmission zero at the lower frequency band using a pair of stepped-impedance stubs, a wide passband filter is further realized. The proposed filter is fed by.a transducer composed of a microstrip line with a flaring ground. The simulated results show that the presented filter has an extremely wide upper stopband in addition to excellent passband filtering characteristics such as low loss, wide band, and high square ratio. A prototype passband filter is also fabricated to validate the predicted performances. The proposed spoof-SPPs filter is believed to be very promising for other surface waveguide components in microwave and terahertz bands.
基金supported by National Natural Science Foundations of China (No.61971052 and No.U20A20203)Key Research and Development Project of Guangdong Province (2020B0101080001)
文摘In this paper,a 5G wideband power amplifier(PA)with bandpass filtering response is synthesized using a bandwidth-extended bandpass filter as the matching network(MN).In this structure,the bandwidth(θ_(C))is defined as a variable in the closedform equations provided by the microstrip bandpass filter.It can be extended over a wide range only by changing the characteristic impedances of the structure.Different from the other wideband MNs,the extension of bandwidth does not increase the complexity of the structure(order n is fixed).In addition,based on the bandwidth-extended structure,the wideband design of bandpass filtering PA is not limited to the fixed bandwidth of the specific filter structure.The theoretical analysis of the MN and the design flow of the PA are provided in this design.The fabricated bandpass filtering PA can support almost one-octave bandwidth(2-3.8 GHz),covering the two 5G bands(n41 and n78).The drain efficiency of 47%-60%and output power higher than 40 dBm are measured.Good frequency selectivity in S-parameter measurements can be observed.
基金supported by the National Natural Science Foundation of China (No.60808004)the New Century Excellent Talents in University (No.NCET-07-0611)the Tianjin Natural Science Foundation (No.08JCYBJC14500)
文摘A tunable microwave photonic bandpass filter with high mainlobe-to-sidelobe ratio (MSR) based on a phase modulator and a dispersive device is proposed. The multi-tap characteristics of the filter are realized by slicing a broadband source using a Mach-Zehnder interferometer (MZI) which results in a high MSR of 25 dB. The tunability of the filter is realized by an optical variable delay line (OVDL) in one arm of the MZI, which changes the wavelength spacing of the sliced broadband source and results in a tunable free spectrum range (FSR) of the filter. The central frequency of the bandpass filter is tunable from 10.7 GHz to 27 GHz by changing the wavelength spacing from 0.145 nm to 0.054 nm.
文摘In this paper, the variational method combined with Green's function is used to analyze the characteristics of suspended, stripline. The result is in good agreement with references. The design of mm-wave end-coupled bandpass filter with suspended substrate is discussed. The computer programs for design of suspended stripline and bandpass filter are established.
基金the National Natural Science Foundation of China(Grant Nos.62071221 and 62071442)the Equipment Advance Research Foundation of China(Grant No.80909010302)the Key Laboratory of Radar Imaging and Microwave Photonics(Nanjing University of Aeronautics and Astronautics),Ministry of Education of China(Grant No.NJ20210006).
文摘A novel bandpass filter(BPF)based on spoof surface plasmon polaritons(SSPPs)using a compact folded slotline structure is proposed and experimentally demonstrated.The proposed novel SSPPs structure compared with a conventional plasmonic waveguide with slot line SSPPs unit structure at the same size,the considerable advantages in much lower asymptotic frequency with tight field confinement,which enable the proposed filter to be more miniaturization.A high-efficient mode conversion structure is designed to transition from TE-mode to SSPPs-mode by gradient slotline lengths.The low-frequency stop-band can be committed with microstrip to slotline evolution on both sides of the dielectric,while the high-frequency cutoff band is realized by the proposed SSPPs structure.The influence of dispersion relation,electric field distribution,surface current,and structural parameters on the transmission characteristics of the proposed BPF are analyzed by finite difference time domain(FDTD).To validate the design concept,the prototype of the miniaturized SSPPs BPF has been manufactured and measured.The experimental results show high performance of the fabricated sample,in which the working in a range of 0.9 GHz-5.2 GHz with the relative bandwidth is 142%,the insertion loss less than 0.5 dB,the reflection coefficient less than-10 dB,and the group delay is less than one ns.This works provides a mirror for realizing the miniaturization of waveguides,and the application and development of high-confinement SSPPs functional devices in the microwave and THz regimes.
文摘This study is concerned with the diagnosis of discrepancies in a steel truss bridge by identifying dynamic properties from the vibration response signals of the bridges.The vibration response signals collected at bridges under three different vehicular speeds of 10 km/hr,20 km/hr,and 30 km/hr are analyzed using statistical features such as kurtosis,magnitude of peak-to-peak,root mean square,crest factor as well as impulse factor in time domain,and Stockwell transform in the time-frequency domain.The considered statistical features except for kurtosis show uncertain behavior.The Stockwell transform showed low-resolution outcomes when the presence of noise in the recorded vibration responses.The elimination of noise and extraction of meaningful dynamic properties from the vibration responses is done by applying a new method which comes from the fusion of Hilbert transform with Spectral kurtosis and bandpass filtering.The outcomes obtained from Hilbert transform processed residual signals which are further filtered using bandpass filter show more robustness and accuracy in characterizing bridge modal frequencies from the noisy vibration responses.The proposed method produces a high-resolution frequency response which can unveil the joint discrepancy in the bridge structure.
基金supported by the National Key Scientific Instrument and Equipment Development Project,China(Grant No.2014YQ030975)the National Natural Science Foundation of China(Grant Nos.61371009 and 61401282)
文摘In this study, we propose a novel resonator that is composed of a modified spiral with an embedded interdigital capacitor. A large ratio of the first spurious frequency to the fundamental resonant frequency is obtained, which is suitable for the design of filters with wide stopbands, and the circuit size is considerably reduced by embedding the interdigital structure in the spiral. For demonstration, a compact four-pole high temperature superconducting（HTS） filter with a center frequency of 568 MHz is designed and fabricated on double-sided YBCO film with a size of 11.4 mm×8.0 mm. The filter measurement shows excellent performance with an out-of-band rejection level better than 60.9 dB up to 3863 MHz.
基金supported by Research Fund for the Doctoral Program of Higher Education of China(Grant No.20060614021)Sichuan Provincial Fundamental Research of China(Grant No.2008JY0057),Fundamental Research Funds for the Central Universities of China(Grant No.ZYGX2009J091)
文摘Modern electronic circuit requires compact,multifunctional technology in communication systems.However,it is very difficult due to the limitations in passive component miniaturization and the complication of fabrication process.The bandpass filter is one of the most important passive components in millimeter（mm）-wave communication system,attracting significant interest in three-dimension（3D） miniaturized design,which is few reported.In this paper,a bandpass filter structure using low-temperature co-fired ceramic（LTCC） technology,which is fully integrated in a system-in package（SIP） communication module,is presented for miniaturized and high reliable mm-wave application.The bandpass filter with 3D end-coupled microstrip resonators is implemented in order to achieve a high performance bandwidth characteristic.Specifically,all of the resonators are embedded into different ceramic layers to decrease the insertion loss and enhance the out-of-band rejection performance by optimizing the coupling coefficient and the coupling strength.A fence structure,which is formed by metal-filled via array with the gap less than quarter wavelength,is placed around the embedded bandpass filter to avoid electromagnetic（EM） interference problem in multilayer structure.This structural model is validated through actual LTCC process.The bandpass filter is successfully manufactured by modifying the co-fireablity characteristics,adjusting the sintering profile,releasing the interfacial stress,and reducing the shrinkage mismatch with different materials.Measured results show good performance and agree well with the high frequency EM full wave simulation.The influence of layer thickness and dielectric constant on the frequency response in fabricated process is analyzed,where thicker ceramic sheets let the filter response shift to higher frequency.Moreover,measured S-parameters denote the center frequency is also strongly influenced by the variation of ceramic material＇s dielectric constants.By analyzing the relationship between the characteristics of the ceramic tape and the center frequency of the filter,both theoretical and experimental data are accumulated for broadening application filed.With the coupling resonators embedded into the ceramic layers,the bandpass filter exhibits advantages of small size and high reliability compared to conventional planar filter structure,which makes the bandpass filter suitable for SIP communicational application.
文摘A prototype IIR bandpass filter is derived from an analog bandpass filter using bilinear transformation. The formulas relating the IIR bandpass filter's coefficients with its centre frequency and bandwidth are obtained. Using N sections of such filters, a cascade IIR bandpass filter is constructed. Based on given specifications and the formulas, the parameter N and the bandwidth of prototype filter can be obtained, and the required cascade IIR bandpass filter is obtained. The filter has a small set of coefficients with a simple structure, therefore is easy to design. The described approach is especially suitable for hardware implementation.
基金supported by the National Training Program of Innovation and Entrepreneurship for Undergraduate(No.201410755013)the Foundation of Xinjiang Education(No.XJEDU2013S04)
文摘We propose a compact dual-band bandpass filter(BPF)based on one-dimensional porous silicon(PS)photonic crystal by electrochemical etching.By inserting three periods of high and low reflective index layers in the center of porous silicon microcavity(PSM),two sharp resonant peaks appear in the high reflectivity stop band on both sides of the resonance wavelength.Through simulation and experiment,the physical mechanisms of the two resonance peaks and the resonance wavelength are also studied.It is found that the resonance wavelength can be tuned only by adjusting the effective optical thickness(EOT)of each PS layer,in which different resonance wavelengths have different widths between the two sharp resonance peaks.Besides,the analysis indicates that oxidization makes the blue shift become larger for high wavelength than that for low wavelength.Such a fabricated BPF based on PS dual-microcavity is easy to be fabricated and low cost,which benefits the application of integrated optical devices.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.U2141232,62071221,and 62071442)the Aeronautical Science Foundation of China(Grant No.2019ZA037001)。
文摘An ultra-wideband bandpass filter(BPF)with a wide out-of-band rejection based on a surface plasmonic waveguide(SPW)slotline with ring grooves is designed and analyzed.A paired microstrip-to-slotline transition is designed for quasiTEM to TM mode conversion by using a microstrip line with a circular pad and the slotline with the same circular slot.The mode conversion between the TM and the surface plasmon polariton(SPP)mode is realized by using a gradient slotline with ring grooves and an impedance matching technique.The upper cut-off frequencies of the passband can be adjusted by using these proposed SPP units,while the lower frequencies of the passband are created by using the microstrip-toslotline transitions to give an ultra-wideband BPF.The dispersion curves of SPP units,electric field distribution,and the transmission spectra of the proposed ultra-wideband bandpass filter are all calculated and analyzed by the finite-difference time-domain(FDTD)method.The simulated results show that the presented filter has good performance including a wide3-dB bandwidth of 149%from 0.57 GHz to 3.93 GHz,an extremely wide 40-dB upper-band rejection from 4.2 GHz to18.5 GHz,and low loss and high selectivity in the passband.To prove the design validity,a prototype of the BPF has been manufactured and measured,showing a reasonable agreement with simulation results.The unique features of the proposed BPF may make it applicable for integrated circuit and plasmonic devices in microwave or THz frequency ranges.
文摘In this paper, the resonant frequency of a dual\|mode dielectric resonator is calculated using a finite difference time\|domain method. A new type of bandpass filter is designed with the calculated coupling coefficient. The filter designed in this paper has reached the design goal, verified by simulation with Ansoft HFSS.
文摘A high performance Balun BandPass Filter (BPF) with capacitively loaded multiple coupled lines with very simple structure is proposed in this paper, this structure realizes simultaneous size reduction and superior harmonic response suppression performance in bandpass filtering meanwhile good differential performance of the Balun. The theory of this structure for unbalanced input into balanced output has been studied in this paper and a proper Balun and BPF characteristic by the symmetric feeding and skew symmetric feeding have been obtained to prove the theory. The enter frequency of the fabricated Balun-BPF is operated at 2.45 GHz with 6.93% Fractional Band Width (FBW), and this frequency is used for Bluetooth and some other communication systems. The differences between the two outputs are 180°± 1.92° in phase and within 0.33 dB in magnitude. At f0, the amplitude imbalance and phase difference are within 0.25 dB and 180.86°, respectively. The measured frequency responses agree well with the simulated ones. With the theoretical analyses and practical results, it is shown that the proposed one has the advantages of simple structure, convenient analysis and good performance of both BPF and Balun.
文摘In this paper,a Slotted Stepped-Impedance Resonator (SSIR) is proposed.Due to the slots in the low-impedance section of the conventional SIR,the new resonator has a lower fundamental resonance f0 and can provide a potential finite transmission zero fz close to f0.Based on the proposed SSIR,a fourth-order Chebychev BandPass Filter (BPF) is designed at f0=1 GHz.The measured results show that a better than-65 dB rejection is achieved on both the lower and the upper stopband.Moreover,the new filter has a wide-30 dB rejection upper stopband from 1.13f0 to 6.52f0.The fabricated filter exhibits a size of The new filter has a planar topology and is easily integrated with modern portable communication systems.
