TiB2P/Al composite was successfully fabricated by squeeze casting technology.Its mechanical and tribological properties were evaluated .The elimination of Ti-Al intermetallic compound was confirmed by X-ray diffracti...TiB2P/Al composite was successfully fabricated by squeeze casting technology.Its mechanical and tribological properties were evaluated .The elimination of Ti-Al intermetallic compound was confirmed by X-ray diffraction （XRD）studies.At 45% volume fraction ,the bending strength at ambient temperature was 934 MPa.And the fracture modes included ductile failure of Al matrix and brittle fracture of TiB2 pqrticles.In dry sliding wear mode ,severe plastic deformation and adhesive wear were found on te worn surfaces of the SiCP/Al composite .But no obvious characteristics of adhesion or abrasion wear were observed on that of the TiB2P/Al composites .At the stedady stage ,the friction coefficient of the SiCP/Al composite was about 0.6 .While that of TiB2P/Al composite was only only about 0.16-0.17.展开更多
The electromagnetic-mechanical stirring technology was employed for preparing QTi4.3-4 graghite composite slurry,and QTi4.3-4 graghite composite with uniform distribution of graphite particles was prepared uring the ...The electromagnetic-mechanical stirring technology was employed for preparing QTi4.3-4 graghite composite slurry,and QTi4.3-4 graghite composite with uniform distribution of graphite particles was prepared uring the semi-solid casting technology successfully.The structure of this QTi4.3-4graphite composite was studied and the condition for uniform distribution of graphite particles was got.The experimental results show that there exists a linear relationship between the solid fraction and the stirring temperature of QTi4.3-4graphite slurry.With the decreasing of stirring temperature,the solid fraction of QTi4.3-4 graghite slurry increases constantly.In casting,with the increasing of solid fraction of QTi4.3-4 graphite slurry.the agglomeration of graphite particles is removed gradually.When the solid fraction is higher than 40%,graphite particles can distribute evenly in QTi4.3-4 graghite composite.展开更多
The 7th Chinese Lost Foam Casting (LFC) Symposium & the 1st LFC Technology Exposition were held on May 21-23 at Nanjing University of Aeronautics and Astronautics (NUAA), and the conference theme was "Recent ...The 7th Chinese Lost Foam Casting (LFC) Symposium & the 1st LFC Technology Exposition were held on May 21-23 at Nanjing University of Aeronautics and Astronautics (NUAA), and the conference theme was "Recent development of lost foam casting technology". Prof. TAO Jie, the Executive Chairman of the conference and the Vice Director of LFC Committee of Foundry Institution of Chinese Mechanical Engineering Society(FICMES), chaired the inauguration. Prof. NIE Hong, the Vice President of NUAA, represented the host address and expressed welcome and gratitude to all the vips from home and abroad. He said the development of the technologies, environmental protection and the trade globalization require to continually improve the performance of products, and accurately select proper material and the manufacturing technology. As the revolutionary technology in casting development history, LFC technology has brought a brand-new change for the machine design and casting production. He hoped the conference would be beneficial to the development of Chinese LFC technololy and wished the symposium a complete success! Prof. YE Sheng-ping, the Executive Chairman of the conference and the Director of LFC Committee of FICMES, gave the opening address and read out the congratulations of F. J. Woestmann (Director of Germany LFC Technology Council), Wolfgang (General Manager of Storopack Hans Reichenecker Group), G Sedlmair Heiko (LFC project director of Teubert Maschinenbau GmbH), etc. Patrice Juton, the Sale Manager of Storopack Group, gave a speech on behalf of the conference delegates.展开更多
In this research, the materials and the compositions of the surface slurries were chosen by considering the characteristics of Ti investment casting. The effects of solid-liquid ratios on the properties of the slurry ...In this research, the materials and the compositions of the surface slurries were chosen by considering the characteristics of Ti investment casting. The effects of solid-liquid ratios on the properties of the slurry and the effects of baking temperatures on the flexural strength have also been investigated. Flawless shells having smooth inner surface were manufactured with proper technology. Ti and its alloys were melted and poured by water-cooled Cu crucible vacuum induction furnace. The qualities of the investment castings made accordingly were studied and analyzed.展开更多
The two production lines for the first phase of the semi-solid die-casting high-end parts project were put into production in this October, and can monthly produce more than 30 thousand die casting parts.
The development and research of titanium cast alloy and its casting technology, especially its application in aeronautical industry in China are presented. The technology of molding, melting and casting of titanium al...The development and research of titanium cast alloy and its casting technology, especially its application in aeronautical industry in China are presented. The technology of molding, melting and casting of titanium alloy, casting quality control are introduced. The existing problems and development trend in titanium alloy casting technology are also discussed.展开更多
Lost foam casting(LFC)technology has been widely applied to cast iron and cast steel.However,the development of LFC for Al and Mg alloys was relatively slower than that for cast iron and cast steel.The application of ...Lost foam casting(LFC)technology has been widely applied to cast iron and cast steel.However,the development of LFC for Al and Mg alloys was relatively slower than that for cast iron and cast steel.The application of LFC to Al and Mg alloys needs more effort,especially in China.In this paper,the development history of LFC is reviewed,and the application situations of LFC to Al and Mg alloys are mainly discussed.Meanwhile,the key problems of LFC for Al and Mg alloys are also pointed out.Finally,the prospects for LFC technology are discussed,and some special new LFC technologies are introduced for casting Al and Mg alloys.In future,the development trends of green LFC technology mainly focus on the special new LFC methods,metal material,coating,heat treatment,new foam materials as well as purification technology of tail gas,etc.展开更多
A theoretical model adapted for studying steel continuous casting technology was proposed. The model based on system theory contained input/output, command, and control parameters. The process was divided .into five s...A theoretical model adapted for studying steel continuous casting technology was proposed. The model based on system theory contained input/output, command, and control parameters. The process was divided .into five stages, i. e. , tundish, mold, guiding system, guiding-drawing system, and guiding-drawing-soft reduction system. The model can be used to describe the physicochemical processes, thermal processes, chemical processes, and characteristics of the cast material according to the above-mentioned stages. It can also be applied to other metallurgical technologies and even to other industries （chemistry, food, etc. ）.展开更多
3D stereoscopic visualization technology is coming into more and more common use in the field of entertainment,and this technology is also beginning to cut a striking figure in casting industry and scientific research...3D stereoscopic visualization technology is coming into more and more common use in the field of entertainment,and this technology is also beginning to cut a striking figure in casting industry and scientific research.The history,fundamental principle,and devices of 3D stereoscopic visualization technology are reviewed in this paper.The authors’research achievements on the 3D stereoscopic visualization technology in the modeling and simulation of the casting process are presented.This technology can be used for the observation of complex 3D solid models of castings and the simulated results of solidification processes such as temperature,fluid flow,displacement,stress strain and microstructure,as well as the predicted defects such as shrinkage/porosity,cracks,and deformation.It can also be used for other areas relating to 3D models,such as assembling of dies,cores,etc.Several cases are given to compare the illustration of simulated results by traditional images and red-blue 3D stereoscopic images.The spatial shape is observed better by the new method.The prospect of3D stereoscopic visualization in the casting aspect is discussed as well.The need for aided-viewing devices is still the most prominent problem of 3D stereoscopic visualization technology.However,3D stereoscopic visualization represents the tendency of visualization technology in the future;and as the problem is solved in the years ahead,great breakthroughs will certainly be made for its application in casting design and modeling and simulation of the casting processes.展开更多
Argon addition into the casting channel reduces the amount of clogging on the refractory wall to allow long sequence casting of aluminium-killed steel grades.The key to minimum surface defects on the final product is ...Argon addition into the casting channel reduces the amount of clogging on the refractory wall to allow long sequence casting of aluminium-killed steel grades.The key to minimum surface defects on the final product is to establish the optimum quantity by optimising the gas distribution below the stopper nose.This is achieved by new argon stopper technology which supports low gas quantities with homogeneous gas and bubble distributions to float non-metallic inclusions(NMI)in the continuous casting mould.展开更多
The Asia-Pacific Die Casting Industry Exhibition 2005, organized by Foundry Institution of Chinese Mechanical Engineering Society （FICMES）, was held in INTEX Shanghai, China on August 14-17, 2005. On August 16th, th...The Asia-Pacific Die Casting Industry Exhibition 2005, organized by Foundry Institution of Chinese Mechanical Engineering Society （FICMES）, was held in INTEX Shanghai, China on August 14-17, 2005. On August 16th, the journalists of CHINA FOUNDRY journal visited five exhibitors on the spot of exhibition. They are： Mr. Roland FINK, General manager of Frech （Shanghai） Die Casting Machine Co. Ltd.; Mr. Thomas STROBL, General manager of Buhler Equipment Engineering （Wuxi） Co. Ltd., Switzerland; Mr. WANG Tong, Manager of ABB Engineering （Shanghai） Co. Ltd.; Ms. Karen LUO, National Sales Manager-Die Casting, Chem-Trend （Shanghai） Trading Co. Ltd.; and Mr. David ZHOU, Sales Supervisor of Acheson, the National Starch ＆ Chemical （Shanghai） Company.展开更多
With the rapid and stable development of China's economy, metallurgical technology, which plays an important role in the development and progress of China's social economy, also needs progress with the times. ...With the rapid and stable development of China's economy, metallurgical technology, which plays an important role in the development and progress of China's social economy, also needs progress with the times. In this paper, several problems existing in electromagnetic continuous casting technology in metallurgical technology are discussed and studied, and its specific application status in the new era and new background is analyzed. At the same time, how to improve and upgrade is discussed in detail, hoping to improve more scientific and reasonable metallurgical technology.展开更多
To address the current issues with the conventional slide gate system utilized in the steel teeming process,a unique electromagnetic induction controlled automated steel teeming(EICAST)technology has been developed.Co...To address the current issues with the conventional slide gate system utilized in the steel teeming process,a unique electromagnetic induction controlled automated steel teeming(EICAST)technology has been developed.Cooling means of spiral coil in this technology is directly related to its service life.Firstly,heat transfer processes of air cooling and spray cooling were compared and analyzed.Secondly,the impacts of water temperature,water flow rate and air flow rate were examined in order to maximize the spray cooling effect.To maintain coil temperature at a low value consistently throughout the entire thermal cycle process of the ladle,a combined cooling mode was finally employed.Numerical simulation was applied to examine the coil temperature variation with different cooling systems and characteristics.Before coil operation,spray cooling is said to be more effective.By controlling the water flow rate and air flow rate,the spray cooling effect is enhanced.However,water temperature has little or no impact when using spray cooling.Air cooling during the secondary refining process and spray cooling prior to coil operation are combined to further lower coil temperature.When the direction of the spray cooling is from bottom to top,the coil temperature is lowered below 165℃.A practical induction coil cooling plan was provided for the EICAST technology’s production process.展开更多
In order to further improve the precision forming efficiency of a sand mold digital patternless casting and reduce the amount of sand mold cutting, a method for near-net forming of the sand mold with digital flexible ...In order to further improve the precision forming efficiency of a sand mold digital patternless casting and reduce the amount of sand mold cutting, a method for near-net forming of the sand mold with digital flexible extrusion technology was put forward. The theory, optimization algorithm and technology for sand mold nearnet forming were studied. Experimental results show that the sand mold forming efficiency can be increased by 34%, and the molding sand can be reduced by 44%. The method for near-net forming of a sand mold with digital flexible extrusion technology can effectively promote the application of digital patternless casting technology in the mass production of castings and thus greatly improves the efficiency and automation of sand mold manufacturing.展开更多
Squeeze casting is a technology with short route,high efficiency and precise forming,possessing features of casting and plastic processing.It is widely used to produce high performance metallic structural parts.As ene...Squeeze casting is a technology with short route,high efficiency and precise forming,possessing features of casting and plastic processing.It is widely used to produce high performance metallic structural parts.As energy conservation and environmental protection concerns have risen,lightweight and high performance metal parts are urgently needed,which accelerated the development of squeeze casting technology over the past two decades in China.In this paper,research progress on squeeze casting alloys,typical parts manufacturing and development of squeeze casting equipment in China are introduced.The future trend and development priorities of squeeze casting are discussed.展开更多
with the development of computer technology, foundry CAE technology has made rapid progress. Commercialsoftware packages of casting process simulation, therefore, have become more and more practical. This paper introd...with the development of computer technology, foundry CAE technology has made rapid progress. Commercialsoftware packages of casting process simulation, therefore, have become more and more practical. This paper introducesboth the recent developments and some applications of InteCAST software, a commercial numerical simulation softwarepackage for foundry industry, with more than 120 customers all over the world. The function modules of lnteCAST8.0 andsome new techniques, such as uneven mesh technology for mold filling simulation and numerical mouse technology fordata visualization, were introduced. Several applications on special castings such as investment casting, low pressure diecasting, and high pressure die casting, were given. These applications showed that the software can help engineers tooptimize casting process by forecasting casting defect.展开更多
文摘TiB2P/Al composite was successfully fabricated by squeeze casting technology.Its mechanical and tribological properties were evaluated .The elimination of Ti-Al intermetallic compound was confirmed by X-ray diffraction （XRD）studies.At 45% volume fraction ,the bending strength at ambient temperature was 934 MPa.And the fracture modes included ductile failure of Al matrix and brittle fracture of TiB2 pqrticles.In dry sliding wear mode ,severe plastic deformation and adhesive wear were found on te worn surfaces of the SiCP/Al composite .But no obvious characteristics of adhesion or abrasion wear were observed on that of the TiB2P/Al composites .At the stedady stage ,the friction coefficient of the SiCP/Al composite was about 0.6 .While that of TiB2P/Al composite was only only about 0.16-0.17.
文摘The electromagnetic-mechanical stirring technology was employed for preparing QTi4.3-4 graghite composite slurry,and QTi4.3-4 graghite composite with uniform distribution of graphite particles was prepared uring the semi-solid casting technology successfully.The structure of this QTi4.3-4graphite composite was studied and the condition for uniform distribution of graphite particles was got.The experimental results show that there exists a linear relationship between the solid fraction and the stirring temperature of QTi4.3-4graphite slurry.With the decreasing of stirring temperature,the solid fraction of QTi4.3-4 graghite slurry increases constantly.In casting,with the increasing of solid fraction of QTi4.3-4 graphite slurry.the agglomeration of graphite particles is removed gradually.When the solid fraction is higher than 40%,graphite particles can distribute evenly in QTi4.3-4 graghite composite.
文摘The 7th Chinese Lost Foam Casting (LFC) Symposium & the 1st LFC Technology Exposition were held on May 21-23 at Nanjing University of Aeronautics and Astronautics (NUAA), and the conference theme was "Recent development of lost foam casting technology". Prof. TAO Jie, the Executive Chairman of the conference and the Vice Director of LFC Committee of Foundry Institution of Chinese Mechanical Engineering Society(FICMES), chaired the inauguration. Prof. NIE Hong, the Vice President of NUAA, represented the host address and expressed welcome and gratitude to all the vips from home and abroad. He said the development of the technologies, environmental protection and the trade globalization require to continually improve the performance of products, and accurately select proper material and the manufacturing technology. As the revolutionary technology in casting development history, LFC technology has brought a brand-new change for the machine design and casting production. He hoped the conference would be beneficial to the development of Chinese LFC technololy and wished the symposium a complete success! Prof. YE Sheng-ping, the Executive Chairman of the conference and the Director of LFC Committee of FICMES, gave the opening address and read out the congratulations of F. J. Woestmann (Director of Germany LFC Technology Council), Wolfgang (General Manager of Storopack Hans Reichenecker Group), G Sedlmair Heiko (LFC project director of Teubert Maschinenbau GmbH), etc. Patrice Juton, the Sale Manager of Storopack Group, gave a speech on behalf of the conference delegates.
文摘In this research, the materials and the compositions of the surface slurries were chosen by considering the characteristics of Ti investment casting. The effects of solid-liquid ratios on the properties of the slurry and the effects of baking temperatures on the flexural strength have also been investigated. Flawless shells having smooth inner surface were manufactured with proper technology. Ti and its alloys were melted and poured by water-cooled Cu crucible vacuum induction furnace. The qualities of the investment castings made accordingly were studied and analyzed.
文摘The two production lines for the first phase of the semi-solid die-casting high-end parts project were put into production in this October, and can monthly produce more than 30 thousand die casting parts.
基金The paper is support by Foundation Key Project of Yunnan:The Study on inoculated theory and reliability of low carbonductile iron, NO. 1999E0004Z
文摘The development and research of titanium cast alloy and its casting technology, especially its application in aeronautical industry in China are presented. The technology of molding, melting and casting of titanium alloy, casting quality control are introduced. The existing problems and development trend in titanium alloy casting technology are also discussed.
基金supported by the National Nature Science Foundation of China(NFSC)(No.50275058,50775085,51204124,51375187)the National High Technology Research and Development Program of China(No.2007AA03Z113)
文摘Lost foam casting(LFC)technology has been widely applied to cast iron and cast steel.However,the development of LFC for Al and Mg alloys was relatively slower than that for cast iron and cast steel.The application of LFC to Al and Mg alloys needs more effort,especially in China.In this paper,the development history of LFC is reviewed,and the application situations of LFC to Al and Mg alloys are mainly discussed.Meanwhile,the key problems of LFC for Al and Mg alloys are also pointed out.Finally,the prospects for LFC technology are discussed,and some special new LFC technologies are introduced for casting Al and Mg alloys.In future,the development trends of green LFC technology mainly focus on the special new LFC methods,metal material,coating,heat treatment,new foam materials as well as purification technology of tail gas,etc.
基金supported by Romanian grant 846 CERES 11/-CEEX 2005-2008 of CNCSIS from Education and Research Ministry.
文摘A theoretical model adapted for studying steel continuous casting technology was proposed. The model based on system theory contained input/output, command, and control parameters. The process was divided .into five stages, i. e. , tundish, mold, guiding system, guiding-drawing system, and guiding-drawing-soft reduction system. The model can be used to describe the physicochemical processes, thermal processes, chemical processes, and characteristics of the cast material according to the above-mentioned stages. It can also be applied to other metallurgical technologies and even to other industries （chemistry, food, etc. ）.
文摘3D stereoscopic visualization technology is coming into more and more common use in the field of entertainment,and this technology is also beginning to cut a striking figure in casting industry and scientific research.The history,fundamental principle,and devices of 3D stereoscopic visualization technology are reviewed in this paper.The authors’research achievements on the 3D stereoscopic visualization technology in the modeling and simulation of the casting process are presented.This technology can be used for the observation of complex 3D solid models of castings and the simulated results of solidification processes such as temperature,fluid flow,displacement,stress strain and microstructure,as well as the predicted defects such as shrinkage/porosity,cracks,and deformation.It can also be used for other areas relating to 3D models,such as assembling of dies,cores,etc.Several cases are given to compare the illustration of simulated results by traditional images and red-blue 3D stereoscopic images.The spatial shape is observed better by the new method.The prospect of3D stereoscopic visualization in the casting aspect is discussed as well.The need for aided-viewing devices is still the most prominent problem of 3D stereoscopic visualization technology.However,3D stereoscopic visualization represents the tendency of visualization technology in the future;and as the problem is solved in the years ahead,great breakthroughs will certainly be made for its application in casting design and modeling and simulation of the casting processes.
文摘Argon addition into the casting channel reduces the amount of clogging on the refractory wall to allow long sequence casting of aluminium-killed steel grades.The key to minimum surface defects on the final product is to establish the optimum quantity by optimising the gas distribution below the stopper nose.This is achieved by new argon stopper technology which supports low gas quantities with homogeneous gas and bubble distributions to float non-metallic inclusions(NMI)in the continuous casting mould.
文摘The Asia-Pacific Die Casting Industry Exhibition 2005, organized by Foundry Institution of Chinese Mechanical Engineering Society （FICMES）, was held in INTEX Shanghai, China on August 14-17, 2005. On August 16th, the journalists of CHINA FOUNDRY journal visited five exhibitors on the spot of exhibition. They are： Mr. Roland FINK, General manager of Frech （Shanghai） Die Casting Machine Co. Ltd.; Mr. Thomas STROBL, General manager of Buhler Equipment Engineering （Wuxi） Co. Ltd., Switzerland; Mr. WANG Tong, Manager of ABB Engineering （Shanghai） Co. Ltd.; Ms. Karen LUO, National Sales Manager-Die Casting, Chem-Trend （Shanghai） Trading Co. Ltd.; and Mr. David ZHOU, Sales Supervisor of Acheson, the National Starch ＆ Chemical （Shanghai） Company.
文摘With the rapid and stable development of China's economy, metallurgical technology, which plays an important role in the development and progress of China's social economy, also needs progress with the times. In this paper, several problems existing in electromagnetic continuous casting technology in metallurgical technology are discussed and studied, and its specific application status in the new era and new background is analyzed. At the same time, how to improve and upgrade is discussed in detail, hoping to improve more scientific and reasonable metallurgical technology.
基金supported by the Startup Foundation of Shenyang Agriculture University(No.X2023050)the Fundamental Research Funds for the Central Universities(No.N2209006)the National Natural Science Foundation of China(No.U22A20173).
文摘To address the current issues with the conventional slide gate system utilized in the steel teeming process,a unique electromagnetic induction controlled automated steel teeming(EICAST)technology has been developed.Cooling means of spiral coil in this technology is directly related to its service life.Firstly,heat transfer processes of air cooling and spray cooling were compared and analyzed.Secondly,the impacts of water temperature,water flow rate and air flow rate were examined in order to maximize the spray cooling effect.To maintain coil temperature at a low value consistently throughout the entire thermal cycle process of the ladle,a combined cooling mode was finally employed.Numerical simulation was applied to examine the coil temperature variation with different cooling systems and characteristics.Before coil operation,spray cooling is said to be more effective.By controlling the water flow rate and air flow rate,the spray cooling effect is enhanced.However,water temperature has little or no impact when using spray cooling.Air cooling during the secondary refining process and spray cooling prior to coil operation are combined to further lower coil temperature.When the direction of the spray cooling is from bottom to top,the coil temperature is lowered below 165℃.A practical induction coil cooling plan was provided for the EICAST technology’s production process.
基金financially supported by the National Science Foundation for Distinguished Young Scholars of China(Grant No.51525503)
文摘In order to further improve the precision forming efficiency of a sand mold digital patternless casting and reduce the amount of sand mold cutting, a method for near-net forming of the sand mold with digital flexible extrusion technology was put forward. The theory, optimization algorithm and technology for sand mold nearnet forming were studied. Experimental results show that the sand mold forming efficiency can be increased by 34%, and the molding sand can be reduced by 44%. The method for near-net forming of a sand mold with digital flexible extrusion technology can effectively promote the application of digital patternless casting technology in the mass production of castings and thus greatly improves the efficiency and automation of sand mold manufacturing.
基金supported by Guangdong-Natural Science Foundation of China(GD-NSFC,grant No.U1034001)Natural Science Foundation of China(grant No.51374110)Specialized Research Fund for Doctoral Program of Higher Education(grant No.20120172110045)
文摘Squeeze casting is a technology with short route,high efficiency and precise forming,possessing features of casting and plastic processing.It is widely used to produce high performance metallic structural parts.As energy conservation and environmental protection concerns have risen,lightweight and high performance metal parts are urgently needed,which accelerated the development of squeeze casting technology over the past two decades in China.In this paper,research progress on squeeze casting alloys,typical parts manufacturing and development of squeeze casting equipment in China are introduced.The future trend and development priorities of squeeze casting are discussed.
文摘with the development of computer technology, foundry CAE technology has made rapid progress. Commercialsoftware packages of casting process simulation, therefore, have become more and more practical. This paper introducesboth the recent developments and some applications of InteCAST software, a commercial numerical simulation softwarepackage for foundry industry, with more than 120 customers all over the world. The function modules of lnteCAST8.0 andsome new techniques, such as uneven mesh technology for mold filling simulation and numerical mouse technology fordata visualization, were introduced. Several applications on special castings such as investment casting, low pressure diecasting, and high pressure die casting, were given. These applications showed that the software can help engineers tooptimize casting process by forecasting casting defect.
