In this paper,we have mainly studied the amplification effect of thulium-doped fiber amplifier(TDFA)at 2µm,and compared different amplification effects of the one-stage TDFA,two-stage TDFA and three-stage TDFA at...In this paper,we have mainly studied the amplification effect of thulium-doped fiber amplifier(TDFA)at 2µm,and compared different amplification effects of the one-stage TDFA,two-stage TDFA and three-stage TDFA at proper conditions.The simulation results show that within the effective threshold,with the increase of the pump power,the amplification effect of the optical amplifier improves,but the signal-to-noise ratio(SNR)of the output signal decreases,in order to balance the gain benefit and noise coefficient of TDFA,we can use a multi-stage amplification structure.Three-stage backward-pumped series 2.06µm TDFA,whose slope efficiency can achieve 11%at certain condition.At 5.2 W pump power,the output signal gain of 2µm TDFA exceeds 20 dB,and the output SNR is higher than 32 dB.In addition,the effect of the optimum length of thulium-doped fiber on the amplification performance of 2µm TDFA is also analyzed in this paper.These simulation results are important for the experiment and design of 2µm TDFA.展开更多
This paper introduces damping amplifier friction vibration absorbers(DAFVAs),compound damping amplifier friction vibration absorbers(CDAFVAs),nested damping amplifier friction vibration absorbers(NDAFVAs),and levered ...This paper introduces damping amplifier friction vibration absorbers(DAFVAs),compound damping amplifier friction vibration absorbers(CDAFVAs),nested damping amplifier friction vibration absorbers(NDAFVAs),and levered damping amplifier friction vibration absorbers(LDAFVAs)for controlling the structural vibrations and addressing the limitations of conventional tuned mass dampers(TMDs)and frictiontuned mass dampers(FTMDs).The closed-form analytical solution for the optimized design parameters is obtained using the H_(2)and H_(∞)optimization approaches.The efficiency of the recently established closed-form equations for the optimal design parameters is confirmed by the analytical examination.The closed form formulas for the dynamic responses of the main structure and the vibration absorbers are derived using the transfer matrix formulations.The foundation is provided by the harmonic and random-white noise excitations.Moreover,the effectiveness of the innovative dampers has been validated through numerical analysis.The optimal DAFVAs,CDAFVAs,NDAFVAs,and LDAFVAs exhibit at least 30%lower vibration reduction capacity compared with the optimal TMD.To demonstrate the effectiveness of the damping amplification mechanism,the novel absorbers are compared with a conventional FTMD.The results show that the optimized novel absorbers achieve at least 91%greater vibration reduction than the FTMD.These results show how the suggested designs might strengthen the structure's resilience to dynamic loads.展开更多
The noise feature of a single-mode class-A laser amplifier is investigated by solving the Maxwell–Bloch equations of motion in the presence of the fluctuation force of cavity Langevin.The aim is to calculate the simu...The noise feature of a single-mode class-A laser amplifier is investigated by solving the Maxwell–Bloch equations of motion in the presence of the fluctuation force of cavity Langevin.The aim is to calculate the simultaneous fluctuations that are superimposed on the amplitude and phase of the cavity electric field, as well as the atomic population inversion. The correlation function of these fluctuations yields the amplitude, phase, and spontaneous emission noise fluxes, respectively. The amplitude and spontaneous emission noise fluxes exhibit the Lorentzian profiles in both the below-threshold state and the injection-locking region of the above-threshold state. While noise is typically viewed negatively in science and engineering, this research highlights its positive role as a valuable tool for measuring the optical properties of a laser amplifier. For instance, the degree of first-order temporal coherence(DFOTC) is derived by taking the Fourier transform of the amplitude noise flux. The damping rate of DFOTC is associated with the coherence time of the light emitted by the laser amplifier. Furthermore, the uncertainty relation between noise bandwidth and coherence time is confirmed. Finally, it is demonstrated that the input pumping noise flux, together with the output amplitude and spontaneous emission noise fluxes, satisfy the principle of flux conservation.展开更多
We present a gain adaptive tuning method for fiber Raman amplifier(FRA) using two-stage neural networks(NNs) and double weights updates. After training the connection weights of two-stage NNs separately in training ph...We present a gain adaptive tuning method for fiber Raman amplifier(FRA) using two-stage neural networks(NNs) and double weights updates. After training the connection weights of two-stage NNs separately in training phase, the connection weights of the unified NN are updated again in verification phase according to error between the predicted and target gains to eliminate the inherent error of the NNs. The simulation results show that the mean of root mean square error(RMSE) and maximum error of gains are 0.131 d B and 0.281 d B, respectively. It shows that the method can realize adaptive adjustment function of FRA gain with high accuracy.展开更多
In a few-mode erbium-doped fiber(FM-EDF),which is a key section in a space-division multiplexing(SDM)communication system,linearly polarized(LP)and orbital angular momentum(OAM)modes,as twomode bases with different ph...In a few-mode erbium-doped fiber(FM-EDF),which is a key section in a space-division multiplexing(SDM)communication system,linearly polarized(LP)and orbital angular momentum(OAM)modes,as twomode bases with different phase profiles,can be transformed into each other.In principle,the LP and OAM modes have a different mode spatial intensity distribution and a gain difference for FM-EDF amplifiers.How to analyze and characterize the differential mode-bases gain(DMBG)is important,but still an issue.We build,for the first time to our knowledge,a local analysis model composed of discrete elements of the FM-EDF cross section in areas of mode spatial intensity distribution azimuthal variation.Using the model of the two mode bases,analysis of local particle number distribution and detailed description of the local gain difference are realized,and the overall gain difference between the two mode bases is obtained.By building an amplifier system based on mode phase profile controlling,the gain of two mode bases is characterized experimentally.The measured DMBG is∼0.8 dB in the second-order mode,which is consistent with the simulation result.This result provides a potential way to reduce the mode gain difference in the FM-EDF,which is important in improving the performance of the SDM communication system.展开更多
Miniaturized erbium-doped waveguide amplifiers attracted great interests in recent decades due to their high gain-efficiency and function-scalability in the telecom C-band.In this work,an erbium-doped thin film lithiu...Miniaturized erbium-doped waveguide amplifiers attracted great interests in recent decades due to their high gain-efficiency and function-scalability in the telecom C-band.In this work,an erbium-doped thin film lithium niobate waveguide amplifier achieving>10 dB off-chip(fiber-to-fiber)net gain and>20 mW fiber-output amplified power is demonstrated,thanks to the low-propagation-loss waveguides and robust waveguide edge-couplers prepared by the photolithography assisted chemomechanical etching technique.Systematic investigation on the fabricated waveguide amplifiers reveals remarkable optical gain around the peak wavelength of 1532 nm as well as the low fiber-coupling loss of-1.2 dB/facet.A fiber Bragg-grating based waveguide laser is further demonstrated using the fabricated waveguide amplifier as the external gain chip,which generates>2 mW off-chip power continuous-wave lasing around the gain peak at 1532 nm.The unambiguous demonstration of fiber-to-fiber net gain of the erbium-doped thinfilm lithium niobate(TFLN)waveguide amplifier as well as its external gain chip application will benefit diverse fields demanding scalable gain elements with highspeed tunability.展开更多
A cavity magnonic oscillator uses the coupling of a planar transmission line oscillator(cavity) and spin excitations(magnons) in a ferrimagnetic material to achieve superior frequency stability and reduced phase noise...A cavity magnonic oscillator uses the coupling of a planar transmission line oscillator(cavity) and spin excitations(magnons) in a ferrimagnetic material to achieve superior frequency stability and reduced phase noise. Like many low phase noise oscillators, a cavity magnonic oscillator faces the challenge that its narrow resonance profile is not well suited for injection locking amplification. This work presents an improved design for such an oscillator configured as an injection locking amplifier(ILA) with an extended lock range. The proposed design features a two-stage architecture, consisting of a pre-amplification oscillator and a cavity magnonic oscillator, separated by an isolator to prevent backward locking.By optimizing the circuit parameters of each stage, the proposed design achieved an order of magnitude increase in lock range, when compared to its predecessors, all while preserving the phase noise quality of the input, making it well-suited for narrowband, sensitive signal amplification. Furthermore, this work provides a method for using oscillators with high spectral purity as injection locking amplifiers.展开更多
For time-of-flight(TOF)light detection and ranging(LiDAR),a three-channel high-performance transimpedance amplifier(TIA)with high immunity to input load capacitance is presented.A regulated cascade(RGC)as the input st...For time-of-flight(TOF)light detection and ranging(LiDAR),a three-channel high-performance transimpedance amplifier(TIA)with high immunity to input load capacitance is presented.A regulated cascade(RGC)as the input stage is at the core of the complementary metal oxide semiconductor(CMOS)circuit chip,giving it more immunity to input photodiode detectors.A simple smart output interface acting as a feedback structure,which is rarely found in other designs,reduces the chip size and power consumption simultaneously.The circuit is designed using a 0.5μm CMOS process technology to achieve low cost.The device delivers a 33.87 dB?transimpedance gain at 350 MHz.With a higher input load capacitance,it shows a-3 dB bandwidth of 461 MHz,indicating a better detector tolerance at the front end of the system.Under a 3.3 V supply voltage,the device consumes 5.2 mW,and the total chip area with three channels is 402.8×597.0μm2(including the test pads).展开更多
In this paper,a simple adaptive power dividing function for the design of a dual-input Doherty power amplifier(DPA)is presented.In the presented approaches,the signal separation function(SSF)at different frequency poi...In this paper,a simple adaptive power dividing function for the design of a dual-input Doherty power amplifier(DPA)is presented.In the presented approaches,the signal separation function(SSF)at different frequency points can be characterized by a polynomial.And in the practical test,the coefficients of SSF can be determined by measuring a small number of data points of input power.Same as other dualinput DPAs,the proposed approach can also achieve high output power and back-off efficiency in a broadband operation band by adjusting the power distribution ratio flexibly.Finally,a 1.5-2.5 GHz highefficiency dual-input Doherty power amplifier is implemented according to this approach.The test results show that the peak power is 48.6-49.7d Bm,and the 6-d B back-off efficiency is 51.0-67.0%,and the saturation efficiency is 52.4-74.6%.The digital predistortion correction is carried out at the frequency points of 1.8/2.1GHz,and the adjacent channel power ratio is lower than-54.5d Bc.Simulation and experiment results can verify the effectiveness and correctness of the proposed method.展开更多
In this paper,a hybrid integrated broadband Doherty power amplifier(DPA)based on a multi-chip module(MCM),whose active devices are fabricated using the gallium nitride(GaN)process and whose passive circuits are fabric...In this paper,a hybrid integrated broadband Doherty power amplifier(DPA)based on a multi-chip module(MCM),whose active devices are fabricated using the gallium nitride(GaN)process and whose passive circuits are fabricated using the gallium arsenide(GaAs)integrated passive device(IPD)process,is proposed for 5G massive multiple-input multiple-output(MIMO)application.An inverted DPA structure with a low-Q output network is proposed to achieve better bandwidth performance,and a single-driver architecture is adopted for a chip with high gain and small area.The proposed DPA has a bandwidth of 4.4-5.0 GHz that can achieve a saturation of more than 45.0 dBm.The gain compression from 37 dBm to saturation power is less than 4 dB,and the average power-added efficiency(PAE)is 36.3%with an 8.5 dB peak-to-average power ratio(PAPR)in 4.5-5.0 GHz.The measured adjacent channel power ratio(ACPR)is better than50 dBc after digital predistortion(DPD),exhibiting satisfactory linearity.展开更多
A Josephson traveling wave parametric amplifier(JTWPA),which is a quantum-limited amplifier with high gain and large bandwidth,is the core device of large-scale measurement and control systems for quantum computing.A ...A Josephson traveling wave parametric amplifier(JTWPA),which is a quantum-limited amplifier with high gain and large bandwidth,is the core device of large-scale measurement and control systems for quantum computing.A typical JTWPA consists of thousands of Josephson junctions connected in series to form a transmission line and hundreds of shunt LC resonators periodically loaded along the line for phase matching.Because the variation of these capacitors and inductors can be detrimental to their high-frequency characteristics,the fabrication of a JTWPA typically necessitates precise processing equipment.To guide the fabrication process and further improve the design for manufacturability,it is necessary to understand how each electronic component affects the amplifier.In this paper,we use the harmonic balance method to conduct a comprehensive study on the impact of nonuniformity and fabrication yield of the electronic components on the performance of a JTWPA.The results provide insightful and scientific guidance for device design and fabrication processes.展开更多
An all-fiber polarization maintaining high-power laser system operating at 1.7 μm based on the Ramaninduced soliton self-frequency shifting effect is demonstrated. The entirely fiberized system is built by erbiumdope...An all-fiber polarization maintaining high-power laser system operating at 1.7 μm based on the Ramaninduced soliton self-frequency shifting effect is demonstrated. The entirely fiberized system is built by erbiumdoped oscillator and two-stage amplifiers with polarization maintaining commercial silica fibers and devices, which can provide robust and stable soliton generation. High-power soliton laser with the average power of 0.28 W,the repetition rate of 42.7 MHz, and pulse duration of 515 fs is generated directly from the main amplifier.Our experiment provides a feasible method for high-power all-fiber polarization maintaining femtosecond laser generation working at 1.7 μm.展开更多
To reduce the negative impact of the power amplifier(PA)nonlinear distortion caused by the orthogonal frequency division multiplexing(OFDM)waveform with high peak-to-average power ratio(PAPR)in integrated radar and co...To reduce the negative impact of the power amplifier(PA)nonlinear distortion caused by the orthogonal frequency division multiplexing(OFDM)waveform with high peak-to-average power ratio(PAPR)in integrated radar and communication(RadCom)systems is studied,the channel estimation in passive sensing scenarios.Adaptive channel estimation methods are proposed based on different pilot patterns,considering nonlinear distortion and channel sparsity.The proposed methods achieve sparse channel results by manipulating the least squares(LS)frequency-domain channel estimation results to preserve the most significant taps.The decision-aided method is used to optimize the sparse channel results to reduce the effect of nonlinear distortion.Numerical results show that the channel estimation performance of the proposed methods is better than that of the conventional methods under different pilot patterns.In addition,the bit error rate performance in communication and passive radar detection performance show that the proposed methods have good comprehensive performance.展开更多
In the field of short-range optical interconnects,the development of low-power-consumption,ultrawideband on-chip optical waveguide amplifiers is of critical importance.Central to this advancement is the creation of ho...In the field of short-range optical interconnects,the development of low-power-consumption,ultrawideband on-chip optical waveguide amplifiers is of critical importance.Central to this advancement is the creation of host materials that require low pump power and provide ultrabroadband emission capabilities.We introduce a tri-doped lanthanum aluminate glass(composition:5Er_(2)O_(3)-5Yb_(2)O_(3)-0.2Tm_(2)O_(3)-43.8La_(2)O_(3)-46Al_(2)O_(3)),which exhibits exceptional near-infrared(NIR)luminescence intensity,significantly outperforming other bands by 3 orders of magnitude.This glass can achieve an ultrawideband NIR gain spanning 478 nm,from 1510 to 1988 nm.Notably,the glass achieves positive optical gain with a low population inversion threshold(P>0.2),highlighting its efficiency and low-power consumption.The high glass transition temperature(Tg∼842°C)and large temperature difference(ΔT∼120°C)between Tg and the onset of crystallization(Tx)indicate excellent thermal stability,which is crucial for producing high-quality amorphous films for on-chip amplifiers.This research examines the unique energy levels and spectral properties of the Er^(3+)-Yb^(3+)-Tm^(3+) tri-doped glass,assessing its potential for use in ultrawideband on-chip optical waveguide amplifiers.This work lays the groundwork for low-power,ultrabroadband on-chip waveguide amplifiers,offering new avenues for short-range optical interconnect systems.展开更多
针对车载自组织网络(Vehicular Ad Hoc Network,VANET)由于车辆距离过远或被障碍物阻挡而导致车对车(Vehicle to Vehicle,V2V)通信可靠性下降的问题,提出了一种基于检测放大转发(Detected Amplify and Forward,DAF)的高可靠通感一体化(I...针对车载自组织网络(Vehicular Ad Hoc Network,VANET)由于车辆距离过远或被障碍物阻挡而导致车对车(Vehicle to Vehicle,V2V)通信可靠性下降的问题,提出了一种基于检测放大转发(Detected Amplify and Forward,DAF)的高可靠通感一体化(Integrated Sensing and Communication,ISAC)空间调制(Spatial Modulation,SM)算法。该算法利用ISAC的雷达探测功能,选取信噪比(Signal to Noise Ratio,SNR)最大的车辆作为中继车辅助源车将信号转发至目的车。在中继车处通过DAF消除噪声累积,提高V2V通信可靠性。在此基础上引入SM算法,利用发送信号的稀疏特性降低邻道干扰以进一步提高V2V通信可靠性。通过理论推导得出中断概率(Outage Probability,OP),仿真验证了不同跳数下发射功率对OP的影响。分析了算法的复杂度和时延。结果表明在不同场景下,该算法在一定复杂度下有效提高了V2V通信的可靠性。该研究为车载自组织网络V2V通信长距离传输提供了低时延且高可靠性的理论支撑。展开更多
基金supported by the Natural Science Foundation of Guangdong Province(Nos.2023A1515010093)the Shenzhen Fundamental Research Program(Nos.JCYJ20220809170611004,20231121110828001 and 20231121113641002)the Taipei University of Technology-Shenzhen University Joint Research Program(No.2024001).
文摘In this paper,we have mainly studied the amplification effect of thulium-doped fiber amplifier(TDFA)at 2µm,and compared different amplification effects of the one-stage TDFA,two-stage TDFA and three-stage TDFA at proper conditions.The simulation results show that within the effective threshold,with the increase of the pump power,the amplification effect of the optical amplifier improves,but the signal-to-noise ratio(SNR)of the output signal decreases,in order to balance the gain benefit and noise coefficient of TDFA,we can use a multi-stage amplification structure.Three-stage backward-pumped series 2.06µm TDFA,whose slope efficiency can achieve 11%at certain condition.At 5.2 W pump power,the output signal gain of 2µm TDFA exceeds 20 dB,and the output SNR is higher than 32 dB.In addition,the effect of the optimum length of thulium-doped fiber on the amplification performance of 2µm TDFA is also analyzed in this paper.These simulation results are important for the experiment and design of 2µm TDFA.
基金the postdoctoral research grant received from the University of Glasgow for the partial financial support for this research work。
文摘This paper introduces damping amplifier friction vibration absorbers(DAFVAs),compound damping amplifier friction vibration absorbers(CDAFVAs),nested damping amplifier friction vibration absorbers(NDAFVAs),and levered damping amplifier friction vibration absorbers(LDAFVAs)for controlling the structural vibrations and addressing the limitations of conventional tuned mass dampers(TMDs)and frictiontuned mass dampers(FTMDs).The closed-form analytical solution for the optimized design parameters is obtained using the H_(2)and H_(∞)optimization approaches.The efficiency of the recently established closed-form equations for the optimal design parameters is confirmed by the analytical examination.The closed form formulas for the dynamic responses of the main structure and the vibration absorbers are derived using the transfer matrix formulations.The foundation is provided by the harmonic and random-white noise excitations.Moreover,the effectiveness of the innovative dampers has been validated through numerical analysis.The optimal DAFVAs,CDAFVAs,NDAFVAs,and LDAFVAs exhibit at least 30%lower vibration reduction capacity compared with the optimal TMD.To demonstrate the effectiveness of the damping amplification mechanism,the novel absorbers are compared with a conventional FTMD.The results show that the optimized novel absorbers achieve at least 91%greater vibration reduction than the FTMD.These results show how the suggested designs might strengthen the structure's resilience to dynamic loads.
文摘The noise feature of a single-mode class-A laser amplifier is investigated by solving the Maxwell–Bloch equations of motion in the presence of the fluctuation force of cavity Langevin.The aim is to calculate the simultaneous fluctuations that are superimposed on the amplitude and phase of the cavity electric field, as well as the atomic population inversion. The correlation function of these fluctuations yields the amplitude, phase, and spontaneous emission noise fluxes, respectively. The amplitude and spontaneous emission noise fluxes exhibit the Lorentzian profiles in both the below-threshold state and the injection-locking region of the above-threshold state. While noise is typically viewed negatively in science and engineering, this research highlights its positive role as a valuable tool for measuring the optical properties of a laser amplifier. For instance, the degree of first-order temporal coherence(DFOTC) is derived by taking the Fourier transform of the amplitude noise flux. The damping rate of DFOTC is associated with the coherence time of the light emitted by the laser amplifier. Furthermore, the uncertainty relation between noise bandwidth and coherence time is confirmed. Finally, it is demonstrated that the input pumping noise flux, together with the output amplitude and spontaneous emission noise fluxes, satisfy the principle of flux conservation.
基金supported by the Natural Science Research Project of Colleges and Universities in Anhui Province (No.KJ2021A0479)the Science Research Program of Anhui University of Finance and Economics (No.ACKYC22082)。
文摘We present a gain adaptive tuning method for fiber Raman amplifier(FRA) using two-stage neural networks(NNs) and double weights updates. After training the connection weights of two-stage NNs separately in training phase, the connection weights of the unified NN are updated again in verification phase according to error between the predicted and target gains to eliminate the inherent error of the NNs. The simulation results show that the mean of root mean square error(RMSE) and maximum error of gains are 0.131 d B and 0.281 d B, respectively. It shows that the method can realize adaptive adjustment function of FRA gain with high accuracy.
基金supported by the National Key Research and Development Program of China(Grant No.2019YFA0706300)the National Natural Science Foundation of China(Grant Nos.U22B2010,62035018,and U2001601)+1 种基金the Program of Marine Economy Development Special Fund(Six Marine Industries)under the Department of Natural Resources of Guangdong Province(Grant No.GDNRC[2024]16)the project supported by the Southern Marine Science and Engineering Guangdong Laboratory(Zhuhai)(Grant No.SML2023SP231).
文摘In a few-mode erbium-doped fiber(FM-EDF),which is a key section in a space-division multiplexing(SDM)communication system,linearly polarized(LP)and orbital angular momentum(OAM)modes,as twomode bases with different phase profiles,can be transformed into each other.In principle,the LP and OAM modes have a different mode spatial intensity distribution and a gain difference for FM-EDF amplifiers.How to analyze and characterize the differential mode-bases gain(DMBG)is important,but still an issue.We build,for the first time to our knowledge,a local analysis model composed of discrete elements of the FM-EDF cross section in areas of mode spatial intensity distribution azimuthal variation.Using the model of the two mode bases,analysis of local particle number distribution and detailed description of the local gain difference are realized,and the overall gain difference between the two mode bases is obtained.By building an amplifier system based on mode phase profile controlling,the gain of two mode bases is characterized experimentally.The measured DMBG is∼0.8 dB in the second-order mode,which is consistent with the simulation result.This result provides a potential way to reduce the mode gain difference in the FM-EDF,which is important in improving the performance of the SDM communication system.
基金financial supports from National Key R&D Program of China(Grant No.2022YFA1205100,2022YFA1404600)National Natural Science Foundation of China(Grant Nos.12192251,12334014,12474325,12134001,12304418,12474378,12274133,12174107,12174113,12274130)+2 种基金the Innovation Program for Quantum Science and Technology(Grant No.2021ZD0301403)Shanghai Municipal Science and Technology Major Project(Grant No.2019SHZDZX01)Fundamental Research Funds for the Central Universities,the Engineering Research Center for Nanophotonics&Advanced Instrument,Ministry of Education,East China Normal University(No.2023nmc005).
文摘Miniaturized erbium-doped waveguide amplifiers attracted great interests in recent decades due to their high gain-efficiency and function-scalability in the telecom C-band.In this work,an erbium-doped thin film lithium niobate waveguide amplifier achieving>10 dB off-chip(fiber-to-fiber)net gain and>20 mW fiber-output amplified power is demonstrated,thanks to the low-propagation-loss waveguides and robust waveguide edge-couplers prepared by the photolithography assisted chemomechanical etching technique.Systematic investigation on the fabricated waveguide amplifiers reveals remarkable optical gain around the peak wavelength of 1532 nm as well as the low fiber-coupling loss of-1.2 dB/facet.A fiber Bragg-grating based waveguide laser is further demonstrated using the fabricated waveguide amplifier as the external gain chip,which generates>2 mW off-chip power continuous-wave lasing around the gain peak at 1532 nm.The unambiguous demonstration of fiber-to-fiber net gain of the erbium-doped thinfilm lithium niobate(TFLN)waveguide amplifier as well as its external gain chip application will benefit diverse fields demanding scalable gain elements with highspeed tunability.
基金funded by NSERC Discovery Grants, NSERC Discovery Accelerator Supplements, Innovation Proof-of-Concept Grant of Research Manitoba, and Faculty of Science Research Innovation and Commercialization Grant of University of Manitoba (C.-M.H.)。
文摘A cavity magnonic oscillator uses the coupling of a planar transmission line oscillator(cavity) and spin excitations(magnons) in a ferrimagnetic material to achieve superior frequency stability and reduced phase noise. Like many low phase noise oscillators, a cavity magnonic oscillator faces the challenge that its narrow resonance profile is not well suited for injection locking amplification. This work presents an improved design for such an oscillator configured as an injection locking amplifier(ILA) with an extended lock range. The proposed design features a two-stage architecture, consisting of a pre-amplification oscillator and a cavity magnonic oscillator, separated by an isolator to prevent backward locking.By optimizing the circuit parameters of each stage, the proposed design achieved an order of magnitude increase in lock range, when compared to its predecessors, all while preserving the phase noise quality of the input, making it well-suited for narrowband, sensitive signal amplification. Furthermore, this work provides a method for using oscillators with high spectral purity as injection locking amplifiers.
文摘For time-of-flight(TOF)light detection and ranging(LiDAR),a three-channel high-performance transimpedance amplifier(TIA)with high immunity to input load capacitance is presented.A regulated cascade(RGC)as the input stage is at the core of the complementary metal oxide semiconductor(CMOS)circuit chip,giving it more immunity to input photodiode detectors.A simple smart output interface acting as a feedback structure,which is rarely found in other designs,reduces the chip size and power consumption simultaneously.The circuit is designed using a 0.5μm CMOS process technology to achieve low cost.The device delivers a 33.87 dB?transimpedance gain at 350 MHz.With a higher input load capacitance,it shows a-3 dB bandwidth of 461 MHz,indicating a better detector tolerance at the front end of the system.Under a 3.3 V supply voltage,the device consumes 5.2 mW,and the total chip area with three channels is 402.8×597.0μm2(including the test pads).
基金supported by National Natural Science Foundation of China(No.62001061)。
文摘In this paper,a simple adaptive power dividing function for the design of a dual-input Doherty power amplifier(DPA)is presented.In the presented approaches,the signal separation function(SSF)at different frequency points can be characterized by a polynomial.And in the practical test,the coefficients of SSF can be determined by measuring a small number of data points of input power.Same as other dualinput DPAs,the proposed approach can also achieve high output power and back-off efficiency in a broadband operation band by adjusting the power distribution ratio flexibly.Finally,a 1.5-2.5 GHz highefficiency dual-input Doherty power amplifier is implemented according to this approach.The test results show that the peak power is 48.6-49.7d Bm,and the 6-d B back-off efficiency is 51.0-67.0%,and the saturation efficiency is 52.4-74.6%.The digital predistortion correction is carried out at the frequency points of 1.8/2.1GHz,and the adjacent channel power ratio is lower than-54.5d Bc.Simulation and experiment results can verify the effectiveness and correctness of the proposed method.
基金supported in part by the National Key Research and Development Program of China(2021YFA0716601)the National Science Fund(62225111).
文摘In this paper,a hybrid integrated broadband Doherty power amplifier(DPA)based on a multi-chip module(MCM),whose active devices are fabricated using the gallium nitride(GaN)process and whose passive circuits are fabricated using the gallium arsenide(GaAs)integrated passive device(IPD)process,is proposed for 5G massive multiple-input multiple-output(MIMO)application.An inverted DPA structure with a low-Q output network is proposed to achieve better bandwidth performance,and a single-driver architecture is adopted for a chip with high gain and small area.The proposed DPA has a bandwidth of 4.4-5.0 GHz that can achieve a saturation of more than 45.0 dBm.The gain compression from 37 dBm to saturation power is less than 4 dB,and the average power-added efficiency(PAE)is 36.3%with an 8.5 dB peak-to-average power ratio(PAPR)in 4.5-5.0 GHz.The measured adjacent channel power ratio(ACPR)is better than50 dBc after digital predistortion(DPD),exhibiting satisfactory linearity.
基金support from the Youth Innovation Promotion Association of Chinese Academy of Sciences (Grant No.2019319)support from the Start-up Foundation of Suzhou Institute of Nano-Tech and Nano-Bionics,CAS,Suzhou (Grant No.Y9AAD110)。
文摘A Josephson traveling wave parametric amplifier(JTWPA),which is a quantum-limited amplifier with high gain and large bandwidth,is the core device of large-scale measurement and control systems for quantum computing.A typical JTWPA consists of thousands of Josephson junctions connected in series to form a transmission line and hundreds of shunt LC resonators periodically loaded along the line for phase matching.Because the variation of these capacitors and inductors can be detrimental to their high-frequency characteristics,the fabrication of a JTWPA typically necessitates precise processing equipment.To guide the fabrication process and further improve the design for manufacturability,it is necessary to understand how each electronic component affects the amplifier.In this paper,we use the harmonic balance method to conduct a comprehensive study on the impact of nonuniformity and fabrication yield of the electronic components on the performance of a JTWPA.The results provide insightful and scientific guidance for device design and fabrication processes.
基金Supported by the National Natural Science Foundation of China (Grant Nos. 10225417 and 61675009)the Natural Science Foundation of Beijing Municipality (Grant Nos. 4204091 and KZ201910005006)the China Postdoctoral Science Foundation (Grant No. 212423)。
文摘An all-fiber polarization maintaining high-power laser system operating at 1.7 μm based on the Ramaninduced soliton self-frequency shifting effect is demonstrated. The entirely fiberized system is built by erbiumdoped oscillator and two-stage amplifiers with polarization maintaining commercial silica fibers and devices, which can provide robust and stable soliton generation. High-power soliton laser with the average power of 0.28 W,the repetition rate of 42.7 MHz, and pulse duration of 515 fs is generated directly from the main amplifier.Our experiment provides a feasible method for high-power all-fiber polarization maintaining femtosecond laser generation working at 1.7 μm.
基金supported by the National Natural Science Foundation of China(61931015,62071335,62250024)the Natural Science Foundation of Hubei Province of China(2021CFA002)+1 种基金the Fundamental Research Funds for the Central Universities of China(2042022dx0001)the Science and Technology Program of Shenzhen(JCYJ20170818112037398).
文摘To reduce the negative impact of the power amplifier(PA)nonlinear distortion caused by the orthogonal frequency division multiplexing(OFDM)waveform with high peak-to-average power ratio(PAPR)in integrated radar and communication(RadCom)systems is studied,the channel estimation in passive sensing scenarios.Adaptive channel estimation methods are proposed based on different pilot patterns,considering nonlinear distortion and channel sparsity.The proposed methods achieve sparse channel results by manipulating the least squares(LS)frequency-domain channel estimation results to preserve the most significant taps.The decision-aided method is used to optimize the sparse channel results to reduce the effect of nonlinear distortion.Numerical results show that the channel estimation performance of the proposed methods is better than that of the conventional methods under different pilot patterns.In addition,the bit error rate performance in communication and passive radar detection performance show that the proposed methods have good comprehensive performance.
基金supported by the National Natural Science Foundation of China(Grant No.62005098)the Fundamental Research Funds for the Central University(Grant No.11623415)the Guangzhou Science and Technology Planning Project(Grant No.202201010320).
文摘In the field of short-range optical interconnects,the development of low-power-consumption,ultrawideband on-chip optical waveguide amplifiers is of critical importance.Central to this advancement is the creation of host materials that require low pump power and provide ultrabroadband emission capabilities.We introduce a tri-doped lanthanum aluminate glass(composition:5Er_(2)O_(3)-5Yb_(2)O_(3)-0.2Tm_(2)O_(3)-43.8La_(2)O_(3)-46Al_(2)O_(3)),which exhibits exceptional near-infrared(NIR)luminescence intensity,significantly outperforming other bands by 3 orders of magnitude.This glass can achieve an ultrawideband NIR gain spanning 478 nm,from 1510 to 1988 nm.Notably,the glass achieves positive optical gain with a low population inversion threshold(P>0.2),highlighting its efficiency and low-power consumption.The high glass transition temperature(Tg∼842°C)and large temperature difference(ΔT∼120°C)between Tg and the onset of crystallization(Tx)indicate excellent thermal stability,which is crucial for producing high-quality amorphous films for on-chip amplifiers.This research examines the unique energy levels and spectral properties of the Er^(3+)-Yb^(3+)-Tm^(3+) tri-doped glass,assessing its potential for use in ultrawideband on-chip optical waveguide amplifiers.This work lays the groundwork for low-power,ultrabroadband on-chip waveguide amplifiers,offering new avenues for short-range optical interconnect systems.
文摘针对车载自组织网络(Vehicular Ad Hoc Network,VANET)由于车辆距离过远或被障碍物阻挡而导致车对车(Vehicle to Vehicle,V2V)通信可靠性下降的问题,提出了一种基于检测放大转发(Detected Amplify and Forward,DAF)的高可靠通感一体化(Integrated Sensing and Communication,ISAC)空间调制(Spatial Modulation,SM)算法。该算法利用ISAC的雷达探测功能,选取信噪比(Signal to Noise Ratio,SNR)最大的车辆作为中继车辅助源车将信号转发至目的车。在中继车处通过DAF消除噪声累积,提高V2V通信可靠性。在此基础上引入SM算法,利用发送信号的稀疏特性降低邻道干扰以进一步提高V2V通信可靠性。通过理论推导得出中断概率(Outage Probability,OP),仿真验证了不同跳数下发射功率对OP的影响。分析了算法的复杂度和时延。结果表明在不同场景下,该算法在一定复杂度下有效提高了V2V通信的可靠性。该研究为车载自组织网络V2V通信长距离传输提供了低时延且高可靠性的理论支撑。
