A hypereutectic Al-3Fe(wt.%)alloy was subjected by rheo-extrusion,and the effect of sub-rapid cooling and shear deformation on the refinement of Fe-rich phase was investigated.The results showed that both the primary ...A hypereutectic Al-3Fe(wt.%)alloy was subjected by rheo-extrusion,and the effect of sub-rapid cooling and shear deformation on the refinement of Fe-rich phase was investigated.The results showed that both the primary Fe-rich phase and eutectic Fe-rich phase in the solidified Al-Fe alloy were finer than the platelike Fe-rich phase in the as-cast Al-Fe alloy with the same content of Fe.The solidified Al-Fe alloy was subjected to three stages of shear deformation,and both the primary Fe-rich phase and eutectic Fe-rich phase were fractured and the average length was refined to 400 nm,while Fe-rich phase in the as-cast Al-3Fe(wt.%)alloy was platelike and its average length was 40 pm.The tensile strength and elongation of the hypereutectic Al-3Fe(wt.%)alloy containing nanosized Fe-rich phase were 162 MPa and 25.78%while those of the as-cast AI-3Fe(wt.%)alloy containing coarse platelike Fe-rich phase were 102 MPa and 16.84%,respectively.In the refineme nt of Fe-rich phase in hypereutectic Al-Fe alloy during rheo-extrusion,the three stages of shear deformation contributed more than sub-rapid cooling.展开更多
The microstructure of Al-Fe-V-Si-Nd alloy prepared by rapid solidification (RS) processing was studied by X-ray diffraction (XRD), transmission electron microscopy (TEM) and high resolution electron microscopy (HREM)....The microstructure of Al-Fe-V-Si-Nd alloy prepared by rapid solidification (RS) processing was studied by X-ray diffraction (XRD), transmission electron microscopy (TEM) and high resolution electron microscopy (HREM). The phase selection of the alloy during solidification and the nucleation behavior of Al8Fe4Nd phase were analyzed within the framework of time-dependent nucleation theory. The incubation time for Al8Fe4Nd phase was found shorter and the nucleation rate higher than those of α-Al. The results indicate the nucleation of Al8Fe4Nd phase is heterogeneous and the dispersoids of Al8Fe4Nd form as primary particles from the liquid, which is consistent with experimental observation.展开更多
Designing novel two-dimensional structures and precisely modulating their second harmonic generation(SHG)attributes are key to advancing nonlinear photonic technologies.In this work,through first-principles calculatio...Designing novel two-dimensional structures and precisely modulating their second harmonic generation(SHG)attributes are key to advancing nonlinear photonic technologies.In this work,through first-principles calculations,we propose a novel tetrahedral phase of transition metal dichalcogenides(TMDs)and validate its structural feasibility in a family of compounds,i.e.,ZX_(2)(Z=Ti,Zr,Hf;X=S,Se,Te).Cohesive energy and phonon dispersion calculations further demonstrate that eight of nine possible ZX_(2)monolayers are dynamically stable.All the ZX_(2)monolayers exhibit pronounced out-of-plane SHG with nonlinear susceptibility components reaching the order of 10^(2)pm/V.Strain engineering imposes a profound influence on the SHG response of ZX_(2)monolayers by reducing symmetry and modifying nonlinear susceptibility components.The redshift and significant enhancement of the prominent peak in SHG spectra are also revealed due to strain-induced charge redistribution and band gap reduction.Intriguingly,strain-driven nonlinear optical switching effects are realized in the ZX_(2)monolayers,with a reversible switching of SHG component ordering under tensile and compressive strain.In such a case,the anisotropic SHG pattern transforms from fourfold to twofold symmetry under the strain.Our work demonstrates the efficacy of strain engineering in precisely enhancing SHG,paving the way for the integration of novel TMD structures into tunable and flexible nonlinear optical devices.展开更多
The effects of solution treatment on the evolution of the second phases and mechanical properties of7075Al alloy werestudied with scanning electron microscopy(SEM),energy dispersive X-ray spectrometry(EDS),differentia...The effects of solution treatment on the evolution of the second phases and mechanical properties of7075Al alloy werestudied with scanning electron microscopy(SEM),energy dispersive X-ray spectrometry(EDS),differential scanning calorimetry(DSC),hardness and tensile tests.The results show that Mg(Zn,Cu,Al)2phases gradually dissolve into the matrix,yet the size andmorphology of Al7Cu2Fe phase exhibit no change with the increase of the solution treatment temperature and time due to its highmelting point.When the solution treatment temperature and time continue to increase,the formation of coarse black Mg2Si particlesoccurs.Compared to the as-cast alloy,the microhardness,tensile strength,and elongation of the sample under solution heat treatmentat460°C for5h are increased by55.1%,40.9%and109.1%,respectively.This is because the eutectic Mg(Zn,Cu,Al)2phases almostcompletely dissolve and basically no coarse black Mg2Si particles are formed.展开更多
Microstructure evolution and damping capacities of Mg–Ce binary alloys with three different Ce contents（0.5, 1, or 2 wt%） have been systematically investigated in this work. Numerous fine parallel second phases in...Microstructure evolution and damping capacities of Mg–Ce binary alloys with three different Ce contents（0.5, 1, or 2 wt%） have been systematically investigated in this work. Numerous fine parallel second phases in Mg–2Ce alloy are obtained, as well as a large number of dislocations around them, but few dislocations appear around the reticular second phase in the Mg–1Ce alloy. Among the three alloys, two internal friction peaks（P;and P;） are detected at about 78 and 167?C in both the Mg–0.5Ce and Mg–1Ce alloys.In addition, the alloy with special parallel second phase structure exhibits excellent damping capacity in both strain amplitude and temperature-dependent regions. These results may be ascribed to the stress concentration and the formation of abundant parallel and uniform dislocation configurations in the ?-Mg matrix without the influence of crystal orientation. The obtained results may provide a novel idea to prepare high-damping magnesium alloys by tailoring their microstructure.展开更多
The effect of equal-channel angular pressing(ECAP)processing at room temperature and 300℃on the distribution of the second phase particles and its influence on hardness and electrical conductivity of the commercial C...The effect of equal-channel angular pressing(ECAP)processing at room temperature and 300℃on the distribution of the second phase particles and its influence on hardness and electrical conductivity of the commercial Cu-0.81Cr-0.07Zr alloy were investigated.Microstructural characterization indicated that the area fraction of coarse Cr-rich particles decreased after ECAP processing.This reduction was attributed to the Cr dissolution induced by plastic deformation.The electrical conductivity of the alloy decreased by 12%after 4 ECAP passes at room temperature due to the increase of electrons scattering caused by higher Cr content in solid solution and higher density of defects in the matrix.These results were supported by the reduction of the Cu lattice parameter and by the exothermic reactions,during differential scanning calorimetry(DSC)analysis,observed only in the samples subjected to ECAP processing.Aging heat treatment after ECAP processing promoted an additional hardening effect and the complete recuperation of the electrical conductivity,caused by the re-precipitation of the partially dissolved particles.The better combination of hardness(191 HV)and electrical conductivity(83.5%(IACS))was obtained after 4 ECAP passes at room temperature and subsequent aging at 380℃for 1 h.展开更多
Effect of the second phase in the micro-galvanic corrosion of a commercial Mg alloy containing rare earth elements, cast WE43 alloy,was investigated in 0.6 M NaCl solution and 0.6 M Na_(2)SO_(4)solution by scanning el...Effect of the second phase in the micro-galvanic corrosion of a commercial Mg alloy containing rare earth elements, cast WE43 alloy,was investigated in 0.6 M NaCl solution and 0.6 M Na_(2)SO_(4)solution by scanning electron microscopy(SEM) observations, scanning Kelvin probe force microscopy(SKPFM) analysis, hydrogen evolution, weight loss measurement, and electrochemical techniques. It is confirmed that the second phase of cast WE43 alloy is more active than Mg matrix and exhibits an anodic role in the micro-galvanic corrosion with α-Mg matrix as cathode and dissolves preferentially in Na_(2)SO_(4)solution, in contrast to the situation in NaCl solution. The corrosion rate of cast WE43 alloy in Na_(2)SO_(4)solution is much higher than that in NaCl solution, which is different from the conventional wisdom and could be attributed to the different role of the second phase in the micro-galvanic corrosion in two solutions.展开更多
Two types of stress relaxation tests were carried out to investigate the incubation time for incipient precipi-tation of Ti（C,N） in deformed austenite and （Ti,Mo）C in ferrite of ferritic Ti-Mo microalloyed steel T...Two types of stress relaxation tests were carried out to investigate the incubation time for incipient precipi-tation of Ti（C,N） in deformed austenite and （Ti,Mo）C in ferrite of ferritic Ti-Mo microalloyed steel The size dis-tribution, amount and chemical composition of precipitates were obtained by using physicochemical phase analysis, and calculated according to thermodynamics and kinetics. The experimental results demonstrated that the incubation time was reduced with increasing Ti content, and prolonged with the addition of Mo. After 30 % deformation at 850 ℃, the nucleation of strain-induced Ti（C,N） was a relatively slow process. On the other hand, the temperature where the nucleation rate of （Ti, Mo）C in ferrite was the highest descended first and then ascended with increasing Ti content, and so did the temperature where the incubation time was the shortest. The key point is that the tempera-ture of steel containing about 0.09 % Ti is the lowest. The mass fraction of MC-type particles with size smaller than 10 nm in steel containing 0.09% Ti and 0.2% Mo reached 73.7%. The size distributions of precipitates in steel containing 0.09% Ti were relatively concentrated compared with that in steel containing 0.07% Ti.展开更多
The second phase particle effect on texture evolution of polycrystalline material is studied through phase-field method. A unique field variable is introduced into the phase-field model to represent the second phase p...The second phase particle effect on texture evolution of polycrystalline material is studied through phase-field method. A unique field variable is introduced into the phase-field model to represent the second phase particles. Elastic interaction between particles and grains is also considered. Results indicate that in the presence of second phase particles the average particle diameter turns smaller than in the absence of these particles and retards texture formation by pinning effect. The second phase particles change the strain energy profile, which tremendously influences the pinning effect.展开更多
The morphology and size of second phase greatly influence the strengthening effect on oxidation dispersion strengthened Mo alloys.In this work,a novel nanostructuring strategy is adopted to modify the second phase of ...The morphology and size of second phase greatly influence the strengthening effect on oxidation dispersion strengthened Mo alloys.In this work,a novel nanostructuring strategy is adopted to modify the second phase of Y_(2)O_(3),and the corresponding effects of particle shape and size on mechanical properties of sintered Mo−Y_(2)O_(3) alloys were investigated.It is found that spherical particles with sizes below 200 nm are preferred due to the dominant intragranular distribution of second phases associated with better strengthening effect originating from dislocation pinning.With smaller particle size of Y_(2)O_(3) nanospheres(105 nm),the tensile strength of corresponding Mo alloy is enhanced by about 43.8%,much higher than that(8.3%)reinforced by second phase nanospheres with larger particle size(322 nm).Meanwhile,with similar particle size(around 100 nm),the spherical shape exhibits better strengthening effect than the one reinforced by one-dimensional rod-like second phase.展开更多
The selective abnormal growth of Goss grains in magnetic sheets of Fe-3%Si （grade Hi-B） induced by second-phase particles （AlN and MnS） was studied using a modified Monte Carlo Ports model. The starting microstruc...The selective abnormal growth of Goss grains in magnetic sheets of Fe-3%Si （grade Hi-B） induced by second-phase particles （AlN and MnS） was studied using a modified Monte Carlo Ports model. The starting microstructures for the simulations were generated from electron backscatter diffraction （EBSD） orientation imaging maps of recrystallized samples. In the simulation, second-phase particles were assumed to be randomly distributed in the initial microstructures and the Zener drag effect of particles on Goss grain boundaries was assumed to be selectively invalid because of the unique properties of Goss grain boundaries. The simulation results suggest that normal growth of the matrix grains stagnates because of the pinning effect of particles on their boundaries. During the onset of abnormal grain growth, some Goss grains with concave boundaries in the initial microstructure grow fast abnormally and other Goss grains with convex boundaries shrink and eventually disappear.展开更多
The second phase particle dispersed in microalloyed steel has different effects on grain growth depending on their size and volume fiaction of the second phase particles which will change during welding thermal cycles...The second phase particle dispersed in microalloyed steel has different effects on grain growth depending on their size and volume fiaction of the second phase particles which will change during welding thermal cycles. The particle coarsening and dissolution kinetics model was analyzed for continuous heating and cooling. In addition, based on experimental data, the coupled equation of grain growth was established by introducing limited size of grain growth with the consideration of the second phase particles pinning effects. Using Monte Carlo method based on experimental data model, the grain growth simulation for heat-affected zone of microalloyed steel welds was achieved. The calculating results were well in agreement with that of experiments.展开更多
The effect of Si addition and heat treatment on the Al-5wt.%Fe al oy has been investigated by OM, SEM-EDS and XRD. The results show that the Si plays a significant role in refining the primary Al3Fe phase. It was foun...The effect of Si addition and heat treatment on the Al-5wt.%Fe al oy has been investigated by OM, SEM-EDS and XRD. The results show that the Si plays a significant role in refining the primary Al3Fe phase. It was found that the addition of 3.0wt.% Si made the al oy present the finest and wel -distributed primary Al3Fe phase, but the Al3Fe phase almost disappeared when 5wt.% Si was added. With further increase in the Si content, some Fe-rich phases appeared in the inter-grains and coarsened. In addition, the heat treatments exert a significant impact on the microstructural evolution of the Al-5wt.%Fe-5wt.%Si al oy. After heat treatment for 28 hours at 590 oC, the coarse platelet or blocky Fe-rich phase in Al-5wt.%Fe-5wt.%Si al oys was granulated; the phase transformation from metastable platelet Al3FeSi and blocky Al8Fe2Si to stable Al5FeSi had occurred. With the extension of heat treatment, the Si phase coarsened gradual y.展开更多
Varying levels of dietary crude proteins and balanced amino acids were fed to layers for a period of eight weeks starting from the twenty-sixth week of age of birds and six weeks into egg production. Effects on perfor...Varying levels of dietary crude proteins and balanced amino acids were fed to layers for a period of eight weeks starting from the twenty-sixth week of age of birds and six weeks into egg production. Effects on performance and haematological characteristics were investigated at this second phase of production. Sixty Black Nera hens were randomly allotted into four (4) dietary treatments, containing the following levels of crude protein 14%, 15%, 16%, 17% and the metabolizable energy was iso-caloric for each treatment. The results showed that there were no significant differences (P > 0.05) observed for lymphocyte, Haemoglobin (Hb), Packed Cell Volume (PCV), Red Blood Cell (RBC) and White Blood Cell (WBC), these haematological parameters were within the range for healthy birds. Thus crude protein level of 14% can be used in diets of layers at the second phase of production provided that adequate amino acids are given, without adverse effect on egg laying, feed intake and measured blood parameters.展开更多
The effects of second phases on the fracture behavior of Mg-10Gd-3Y-0.6Zr alloy were investigated.The results show that the fracture mode can be generally described as ductile transgranular fracture in as-extruded con...The effects of second phases on the fracture behavior of Mg-10Gd-3Y-0.6Zr alloy were investigated.The results show that the fracture mode can be generally described as ductile transgranular fracture in as-extruded condition and intergranular fracture in peak-aged condition.In as-extruded condition,the ductile transgranular fracture occurs by the formation and transgranular propagation of the microcrack from the broken primary phases.However,as the collaboration effects of precipitates inside grains and on the grain boundaries have the tendency to reduce the cohesive strength of the grain boundary,and make the grain boundaries the favorable path for crack propagation,the intergranular fracture occurs in peak-aged condition.展开更多
On the basis of the grain boundary equation by HeUman and corresponding analysis of Worner, this article deals with the interaction range between the second-phase particle （SPP） and grain boundary （GB） as viewed f...On the basis of the grain boundary equation by HeUman and corresponding analysis of Worner, this article deals with the interaction range between the second-phase particle （SPP） and grain boundary （GB） as viewed from the applicability of grain boundary equation. Also, a new expression describing the interaction range has been derived, which solves the problem in theory that the interaction range between SPP and GB can only be qualitatively analyzed previously. It is shown that given the interaction position between SPP and GB, the interaction range can be quantitatively determined by use of this expression.展开更多
The Cu-24 Pb-x Sn(wt%)(x=0,2,4,6)alloys with Pb-rich second-phase particles(SPPs)in different shapes show obviously differently mechanical and self-lubricating properties.The influence of the SPPs’shape difference on...The Cu-24 Pb-x Sn(wt%)(x=0,2,4,6)alloys with Pb-rich second-phase particles(SPPs)in different shapes show obviously differently mechanical and self-lubricating properties.The influence of the SPPs’shape difference on the alloys’mechanical and self-lubricating properties was revealed.Cu-24 Pb alloy with continuously netty SPPs shows much more intensive stick-slip phenomenon during dry sliding than the other three alloys with independently rodlike SPPs.That is mainly due to insufficient lubrication resulted by the netty SPPs’splitting matrix.With the SPPs transforming from netty to rodlike shape under the addition of Sn,the stick-slip phenomenon was notably weakened,which was proven to be related to the higher self-lubricating property of alloys with rodlike SPPs.Simultaneously,the simultaneous increase of ductility and tensile strength was observed in the Cu-24 Pb-x Sn alloys with increasing Sn content,which is because the netty SPPs’splitting behavior will be weakened with them replaced by the rodlike SPPs.展开更多
Background: Capecitabine and irinotecan combination therapy(XELIRI) has been examined at various dose levels to treat metastatic colorectal cancer(m CRC). Recently, in the Association of Medical Oncology of the German...Background: Capecitabine and irinotecan combination therapy(XELIRI) has been examined at various dose levels to treat metastatic colorectal cancer(m CRC). Recently, in the Association of Medical Oncology of the German Cancer Society(AIO) 0604 trial, tri?weekly XELIRI plus bevacizumab, with reduced doses of irinotecan(200 mg/m^2 on day 1) and capecitabine(1600 mg/m^2 on days 1–14), repeated every 3 weeks, has shown favorable tolerability and eicacy which were comparable to those of capecitabine and oxaliplatin(XELOX) plus bevacizumab. The doses of capecit?abine and irinotecan in the AIO trial are considered optimal. In a phase I/II study, XELIRI plus bevacizumab(BIX) as second?line chemotherapy was well tolerated and had promising eicacy in Japanese patients.Methods: The Asian XELIRI Projec T(AXEPT) is an East Asian collaborative, open?labelled, randomized, phase Ⅲ clinical trial which was designed to demonstrate the non?inferiority of XELIRI with or without bevacizumab versus standard FOLFIRI(5?fluorouracil, leucovorin, and irinotecan combination) with or without bevacizumab as second?line chemo?therapy for patients with m CRC. Patients with 20 years of age or older, histologically conirmed m CRC, Eastern Coop?erative Oncology Group performance status 0–2, adequate organ function, and disease progression or intolerance of the irst?line regimen will be eligible. Patients will be randomized(1:1) to receive standard FOLFIRI with or with?out bevacizumab(5 mg/kg on day 1), repeated every 2 weeks(FOLIRI arm) or XELIRI with or without bevacizumab(7.5 mg/kg on day 1), repeated every 3 weeks(XELIRI arm). A total of 464 events were estimated as necessary to show non?inferiority with a power of 80% at a one?sided α of 0.025, requiring a target sample size of 600 patients. The 95% conidence interval(CI) upper limit of the hazard ratio was pre?speciied as less than 1.3.Conclusion: The Asian XELIRI Projec T is a multinational phase III trial being conducted to provide evidence for XELIRI with or without bevacizumab as a second?line treatment option of mCRC.展开更多
In this study, the microstructure and second-phase particles in yttrium （0.05 wt.%and 0.8 wt.%） bearing Fe-10Ni-7Mn steels were characterized. The results of X-ray analysis as well as scanning electron microscopy co...In this study, the microstructure and second-phase particles in yttrium （0.05 wt.%and 0.8 wt.%） bearing Fe-10Ni-7Mn steels were characterized. The results of X-ray analysis as well as scanning electron microscopy coupled with energy dispersive X-ray spectroscopy indicated the formation of （Fe, Ni, Mn）17Y2 precipitates with hexagonal structure in a Fe-10Ni-7Mn-0.8Y （wt.%） alloy. Lattice parameters of these precipitates were calculated as follows：a=0.8485 nm and c=0.8274 nm. Formation of Y2O3 sub-micron particles was also confirmed in both yttrium bearing steels via electrolytic phase extraction method. The effect of these precipitates on the prior austenite grain size was investigated. The results revealed that these precipitates had an effective role in controlling the prior austenite grain size.展开更多
Here we propose a hybrid polymer-LN waveguide for achieving phase-matched second-harmonic generation(SHG).From the aspect of super-mode theory,the geometric parameters of the hybrid semi-nonlinear waveguide were optim...Here we propose a hybrid polymer-LN waveguide for achieving phase-matched second-harmonic generation(SHG).From the aspect of super-mode theory,the geometric parameters of the hybrid semi-nonlinear waveguide were optimized to utilize both symmetric(even)and antisymmetric(odd)modes of the pump and SHG waves so as to facilitate phase matching with large modal overlap.Phase matching between a fundamental even(TE_(00)-like)mode at 1320 nm and a fundamental odd(TE_(01)-like)mode at 660 nm was found with a calculated modal overlap integral of 0.299,while utilizing the largest nonlinear coefficient d_(33),and achieving an efficient calculated normalized conversion efficiency of 148%W^(-1)·cm^(-2).Considering the fabrication feasibility of such hybrid waveguide with features including etchless,large dimension,and low structural sensitivity,we believe our findings would provide a useful reference for future on-chip efficient nonlinear conversion devices.展开更多
基金the National Key Research and Development Program under Grant No.2018YFB2001800the National Natural Science Foundation of China under Grant Nos.51674077 and 51871184+1 种基金Joint fund between Shenyang National Laboratory for Materials Science and State Key Laboratory of Advanced Processing and Recycling of Nonferrous Metals under Grant No.18LHPYO13High-Level Talent Support Program of Liaoning under Grant No.XLYC1802128。
文摘A hypereutectic Al-3Fe(wt.%)alloy was subjected by rheo-extrusion,and the effect of sub-rapid cooling and shear deformation on the refinement of Fe-rich phase was investigated.The results showed that both the primary Fe-rich phase and eutectic Fe-rich phase in the solidified Al-Fe alloy were finer than the platelike Fe-rich phase in the as-cast Al-Fe alloy with the same content of Fe.The solidified Al-Fe alloy was subjected to three stages of shear deformation,and both the primary Fe-rich phase and eutectic Fe-rich phase were fractured and the average length was refined to 400 nm,while Fe-rich phase in the as-cast Al-3Fe(wt.%)alloy was platelike and its average length was 40 pm.The tensile strength and elongation of the hypereutectic Al-3Fe(wt.%)alloy containing nanosized Fe-rich phase were 162 MPa and 25.78%while those of the as-cast AI-3Fe(wt.%)alloy containing coarse platelike Fe-rich phase were 102 MPa and 16.84%,respectively.In the refineme nt of Fe-rich phase in hypereutectic Al-Fe alloy during rheo-extrusion,the three stages of shear deformation contributed more than sub-rapid cooling.
基金The financial supports from the National Science Foundation of China (Grant No 59771020) Post-doctoral Foundation of China.
文摘The microstructure of Al-Fe-V-Si-Nd alloy prepared by rapid solidification (RS) processing was studied by X-ray diffraction (XRD), transmission electron microscopy (TEM) and high resolution electron microscopy (HREM). The phase selection of the alloy during solidification and the nucleation behavior of Al8Fe4Nd phase were analyzed within the framework of time-dependent nucleation theory. The incubation time for Al8Fe4Nd phase was found shorter and the nucleation rate higher than those of α-Al. The results indicate the nucleation of Al8Fe4Nd phase is heterogeneous and the dispersoids of Al8Fe4Nd form as primary particles from the liquid, which is consistent with experimental observation.
基金supported by the National Natural Science Foundation of China(Grant Nos.12304220,12174157,12074150,and 12374174)the Natural Science Foundation of Jiangsu Province(Grant No.BK20230518)+2 种基金the China Postdoctoral Science Foundation(Grant No.2023M731383)the College Student Innovation Project(Grant No.202410299946X)the Scientific Research Project of Jiangsu University(Grant No.22A397).
文摘Designing novel two-dimensional structures and precisely modulating their second harmonic generation(SHG)attributes are key to advancing nonlinear photonic technologies.In this work,through first-principles calculations,we propose a novel tetrahedral phase of transition metal dichalcogenides(TMDs)and validate its structural feasibility in a family of compounds,i.e.,ZX_(2)(Z=Ti,Zr,Hf;X=S,Se,Te).Cohesive energy and phonon dispersion calculations further demonstrate that eight of nine possible ZX_(2)monolayers are dynamically stable.All the ZX_(2)monolayers exhibit pronounced out-of-plane SHG with nonlinear susceptibility components reaching the order of 10^(2)pm/V.Strain engineering imposes a profound influence on the SHG response of ZX_(2)monolayers by reducing symmetry and modifying nonlinear susceptibility components.The redshift and significant enhancement of the prominent peak in SHG spectra are also revealed due to strain-induced charge redistribution and band gap reduction.Intriguingly,strain-driven nonlinear optical switching effects are realized in the ZX_(2)monolayers,with a reversible switching of SHG component ordering under tensile and compressive strain.In such a case,the anisotropic SHG pattern transforms from fourfold to twofold symmetry under the strain.Our work demonstrates the efficacy of strain engineering in precisely enhancing SHG,paving the way for the integration of novel TMD structures into tunable and flexible nonlinear optical devices.
基金Project(51364035)supported by the National Natural Science Foundation of ChinaProject(CX2015055)supported by the Innovation Special Funds of Nanchang University for Graduate Student,China
文摘The effects of solution treatment on the evolution of the second phases and mechanical properties of7075Al alloy werestudied with scanning electron microscopy(SEM),energy dispersive X-ray spectrometry(EDS),differential scanning calorimetry(DSC),hardness and tensile tests.The results show that Mg(Zn,Cu,Al)2phases gradually dissolve into the matrix,yet the size andmorphology of Al7Cu2Fe phase exhibit no change with the increase of the solution treatment temperature and time due to its highmelting point.When the solution treatment temperature and time continue to increase,the formation of coarse black Mg2Si particlesoccurs.Compared to the as-cast alloy,the microhardness,tensile strength,and elongation of the sample under solution heat treatmentat460°C for5h are increased by55.1%,40.9%and109.1%,respectively.This is because the eutectic Mg(Zn,Cu,Al)2phases almostcompletely dissolve and basically no coarse black Mg2Si particles are formed.
基金financially supported by the National Natural Science Foundation of China (No. 51271206, No. 51571044)the National Basic Research Program of China (No. 2013CB632201)+1 种基金the Basic Research Project of Chongqing (cstc2015jcyj BX0081)National Key Research and Development Program (No. 2016YFB0301102)
文摘Microstructure evolution and damping capacities of Mg–Ce binary alloys with three different Ce contents（0.5, 1, or 2 wt%） have been systematically investigated in this work. Numerous fine parallel second phases in Mg–2Ce alloy are obtained, as well as a large number of dislocations around them, but few dislocations appear around the reticular second phase in the Mg–1Ce alloy. Among the three alloys, two internal friction peaks（P;and P;） are detected at about 78 and 167?C in both the Mg–0.5Ce and Mg–1Ce alloys.In addition, the alloy with special parallel second phase structure exhibits excellent damping capacity in both strain amplitude and temperature-dependent regions. These results may be ascribed to the stress concentration and the formation of abundant parallel and uniform dislocation configurations in the ?-Mg matrix without the influence of crystal orientation. The obtained results may provide a novel idea to prepare high-damping magnesium alloys by tailoring their microstructure.
文摘The effect of equal-channel angular pressing(ECAP)processing at room temperature and 300℃on the distribution of the second phase particles and its influence on hardness and electrical conductivity of the commercial Cu-0.81Cr-0.07Zr alloy were investigated.Microstructural characterization indicated that the area fraction of coarse Cr-rich particles decreased after ECAP processing.This reduction was attributed to the Cr dissolution induced by plastic deformation.The electrical conductivity of the alloy decreased by 12%after 4 ECAP passes at room temperature due to the increase of electrons scattering caused by higher Cr content in solid solution and higher density of defects in the matrix.These results were supported by the reduction of the Cu lattice parameter and by the exothermic reactions,during differential scanning calorimetry(DSC)analysis,observed only in the samples subjected to ECAP processing.Aging heat treatment after ECAP processing promoted an additional hardening effect and the complete recuperation of the electrical conductivity,caused by the re-precipitation of the partially dissolved particles.The better combination of hardness(191 HV)and electrical conductivity(83.5%(IACS))was obtained after 4 ECAP passes at room temperature and subsequent aging at 380℃for 1 h.
基金funded by the National Key Research and Development Program of China (Grant No. 2016YFB0301001 and 2016YFB0301101)Major Projects for Collaborative Innovation of Zhengzhou (Grant No.18XTZX12010)Certificate of Postdoctoral Research Grant in Henan Province (Grant No. 201903011)。
文摘Effect of the second phase in the micro-galvanic corrosion of a commercial Mg alloy containing rare earth elements, cast WE43 alloy,was investigated in 0.6 M NaCl solution and 0.6 M Na_(2)SO_(4)solution by scanning electron microscopy(SEM) observations, scanning Kelvin probe force microscopy(SKPFM) analysis, hydrogen evolution, weight loss measurement, and electrochemical techniques. It is confirmed that the second phase of cast WE43 alloy is more active than Mg matrix and exhibits an anodic role in the micro-galvanic corrosion with α-Mg matrix as cathode and dissolves preferentially in Na_(2)SO_(4)solution, in contrast to the situation in NaCl solution. The corrosion rate of cast WE43 alloy in Na_(2)SO_(4)solution is much higher than that in NaCl solution, which is different from the conventional wisdom and could be attributed to the different role of the second phase in the micro-galvanic corrosion in two solutions.
基金Item Sponsored by National Key Technology Research and Development Program in 11th Five-Year Plan of China (2006BE03A0)
文摘Two types of stress relaxation tests were carried out to investigate the incubation time for incipient precipi-tation of Ti（C,N） in deformed austenite and （Ti,Mo）C in ferrite of ferritic Ti-Mo microalloyed steel The size dis-tribution, amount and chemical composition of precipitates were obtained by using physicochemical phase analysis, and calculated according to thermodynamics and kinetics. The experimental results demonstrated that the incubation time was reduced with increasing Ti content, and prolonged with the addition of Mo. After 30 % deformation at 850 ℃, the nucleation of strain-induced Ti（C,N） was a relatively slow process. On the other hand, the temperature where the nucleation rate of （Ti, Mo）C in ferrite was the highest descended first and then ascended with increasing Ti content, and so did the temperature where the incubation time was the shortest. The key point is that the tempera-ture of steel containing about 0.09 % Ti is the lowest. The mass fraction of MC-type particles with size smaller than 10 nm in steel containing 0.09% Ti and 0.2% Mo reached 73.7%. The size distributions of precipitates in steel containing 0.09% Ti were relatively concentrated compared with that in steel containing 0.07% Ti.
基金supported by the National Natural Science Foundation of China(Grant Nos.51174168,and 51274167)"111"Project,China(Grant No.B08040)
文摘The second phase particle effect on texture evolution of polycrystalline material is studied through phase-field method. A unique field variable is introduced into the phase-field model to represent the second phase particles. Elastic interaction between particles and grains is also considered. Results indicate that in the presence of second phase particles the average particle diameter turns smaller than in the absence of these particles and retards texture formation by pinning effect. The second phase particles change the strain energy profile, which tremendously influences the pinning effect.
基金financially supported by the National Key R&D Program of China (No. 2017YFB0306001)Guangxi Key Laboratory of Manufacturing System and Advanced Manufacturing Technology, China (No. 20-065-40-001k)。
文摘The morphology and size of second phase greatly influence the strengthening effect on oxidation dispersion strengthened Mo alloys.In this work,a novel nanostructuring strategy is adopted to modify the second phase of Y_(2)O_(3),and the corresponding effects of particle shape and size on mechanical properties of sintered Mo−Y_(2)O_(3) alloys were investigated.It is found that spherical particles with sizes below 200 nm are preferred due to the dominant intragranular distribution of second phases associated with better strengthening effect originating from dislocation pinning.With smaller particle size of Y_(2)O_(3) nanospheres(105 nm),the tensile strength of corresponding Mo alloy is enhanced by about 43.8%,much higher than that(8.3%)reinforced by second phase nanospheres with larger particle size(322 nm).Meanwhile,with similar particle size(around 100 nm),the spherical shape exhibits better strengthening effect than the one reinforced by one-dimensional rod-like second phase.
基金financially supported by the National Key Research and Development Program of China(No 2016YFB0700505)the China’s State Grid Corporation of Science and Technology Projects(No.SGRI-WD71-13-002)+1 种基金the National Natural Science Foundation of China(Nos.51571020 and 51371030)the Nationa High Technology Research and Development Program of China(No.2015AA034201)
文摘The selective abnormal growth of Goss grains in magnetic sheets of Fe-3%Si （grade Hi-B） induced by second-phase particles （AlN and MnS） was studied using a modified Monte Carlo Ports model. The starting microstructures for the simulations were generated from electron backscatter diffraction （EBSD） orientation imaging maps of recrystallized samples. In the simulation, second-phase particles were assumed to be randomly distributed in the initial microstructures and the Zener drag effect of particles on Goss grain boundaries was assumed to be selectively invalid because of the unique properties of Goss grain boundaries. The simulation results suggest that normal growth of the matrix grains stagnates because of the pinning effect of particles on their boundaries. During the onset of abnormal grain growth, some Goss grains with concave boundaries in the initial microstructure grow fast abnormally and other Goss grains with convex boundaries shrink and eventually disappear.
文摘The second phase particle dispersed in microalloyed steel has different effects on grain growth depending on their size and volume fiaction of the second phase particles which will change during welding thermal cycles. The particle coarsening and dissolution kinetics model was analyzed for continuous heating and cooling. In addition, based on experimental data, the coupled equation of grain growth was established by introducing limited size of grain growth with the consideration of the second phase particles pinning effects. Using Monte Carlo method based on experimental data model, the grain growth simulation for heat-affected zone of microalloyed steel welds was achieved. The calculating results were well in agreement with that of experiments.
基金supported financially by the Strategic Priority Research Program CAS under Grant No.XDA03010304the National Natural Science Foundation of China under Grant No.91226204the Youth Innovation Promotion Association CAS
文摘The effect of Si addition and heat treatment on the Al-5wt.%Fe al oy has been investigated by OM, SEM-EDS and XRD. The results show that the Si plays a significant role in refining the primary Al3Fe phase. It was found that the addition of 3.0wt.% Si made the al oy present the finest and wel -distributed primary Al3Fe phase, but the Al3Fe phase almost disappeared when 5wt.% Si was added. With further increase in the Si content, some Fe-rich phases appeared in the inter-grains and coarsened. In addition, the heat treatments exert a significant impact on the microstructural evolution of the Al-5wt.%Fe-5wt.%Si al oy. After heat treatment for 28 hours at 590 oC, the coarse platelet or blocky Fe-rich phase in Al-5wt.%Fe-5wt.%Si al oys was granulated; the phase transformation from metastable platelet Al3FeSi and blocky Al8Fe2Si to stable Al5FeSi had occurred. With the extension of heat treatment, the Si phase coarsened gradual y.
文摘Varying levels of dietary crude proteins and balanced amino acids were fed to layers for a period of eight weeks starting from the twenty-sixth week of age of birds and six weeks into egg production. Effects on performance and haematological characteristics were investigated at this second phase of production. Sixty Black Nera hens were randomly allotted into four (4) dietary treatments, containing the following levels of crude protein 14%, 15%, 16%, 17% and the metabolizable energy was iso-caloric for each treatment. The results showed that there were no significant differences (P > 0.05) observed for lymphocyte, Haemoglobin (Hb), Packed Cell Volume (PCV), Red Blood Cell (RBC) and White Blood Cell (WBC), these haematological parameters were within the range for healthy birds. Thus crude protein level of 14% can be used in diets of layers at the second phase of production provided that adequate amino acids are given, without adverse effect on egg laying, feed intake and measured blood parameters.
基金Project(IRT0713)supported by the Program for Changjiang Scholars and Innovative Research Team in Chinese UniversityProjects(2007CB613701,2007CB613702)supported by National Basic Research Program of China
文摘The effects of second phases on the fracture behavior of Mg-10Gd-3Y-0.6Zr alloy were investigated.The results show that the fracture mode can be generally described as ductile transgranular fracture in as-extruded condition and intergranular fracture in peak-aged condition.In as-extruded condition,the ductile transgranular fracture occurs by the formation and transgranular propagation of the microcrack from the broken primary phases.However,as the collaboration effects of precipitates inside grains and on the grain boundaries have the tendency to reduce the cohesive strength of the grain boundary,and make the grain boundaries the favorable path for crack propagation,the intergranular fracture occurs in peak-aged condition.
基金the financial support from the Supporting Plan for New Century Excellent Talents,MOE,China under grant No.NCET-04-0257the National Natural Science Foundation of China(No.50471070)the Natural Science Foundation of Shanxi Province(No.20051050).
文摘On the basis of the grain boundary equation by HeUman and corresponding analysis of Worner, this article deals with the interaction range between the second-phase particle （SPP） and grain boundary （GB） as viewed from the applicability of grain boundary equation. Also, a new expression describing the interaction range has been derived, which solves the problem in theory that the interaction range between SPP and GB can only be qualitatively analyzed previously. It is shown that given the interaction position between SPP and GB, the interaction range can be quantitatively determined by use of this expression.
基金supported financially by the National Key Research and Development Program of China(Nos.2016YFB0301303 and 2017YFB0306105)the National Natural Science Foundation of China(Nos.51871041,51771040and51690163)the Fundamental Research Funds for the Central Universities of China(No.DUT17JC44).
文摘The Cu-24 Pb-x Sn(wt%)(x=0,2,4,6)alloys with Pb-rich second-phase particles(SPPs)in different shapes show obviously differently mechanical and self-lubricating properties.The influence of the SPPs’shape difference on the alloys’mechanical and self-lubricating properties was revealed.Cu-24 Pb alloy with continuously netty SPPs shows much more intensive stick-slip phenomenon during dry sliding than the other three alloys with independently rodlike SPPs.That is mainly due to insufficient lubrication resulted by the netty SPPs’splitting matrix.With the SPPs transforming from netty to rodlike shape under the addition of Sn,the stick-slip phenomenon was notably weakened,which was proven to be related to the higher self-lubricating property of alloys with rodlike SPPs.Simultaneously,the simultaneous increase of ductility and tensile strength was observed in the Cu-24 Pb-x Sn alloys with increasing Sn content,which is because the netty SPPs’splitting behavior will be weakened with them replaced by the rodlike SPPs.
基金funding from Chugai Pharmaceutical Co.Ltd.Roche Korea Co.Ltd.Roche Shanghai.Co.Ltd
文摘Background: Capecitabine and irinotecan combination therapy(XELIRI) has been examined at various dose levels to treat metastatic colorectal cancer(m CRC). Recently, in the Association of Medical Oncology of the German Cancer Society(AIO) 0604 trial, tri?weekly XELIRI plus bevacizumab, with reduced doses of irinotecan(200 mg/m^2 on day 1) and capecitabine(1600 mg/m^2 on days 1–14), repeated every 3 weeks, has shown favorable tolerability and eicacy which were comparable to those of capecitabine and oxaliplatin(XELOX) plus bevacizumab. The doses of capecit?abine and irinotecan in the AIO trial are considered optimal. In a phase I/II study, XELIRI plus bevacizumab(BIX) as second?line chemotherapy was well tolerated and had promising eicacy in Japanese patients.Methods: The Asian XELIRI Projec T(AXEPT) is an East Asian collaborative, open?labelled, randomized, phase Ⅲ clinical trial which was designed to demonstrate the non?inferiority of XELIRI with or without bevacizumab versus standard FOLFIRI(5?fluorouracil, leucovorin, and irinotecan combination) with or without bevacizumab as second?line chemo?therapy for patients with m CRC. Patients with 20 years of age or older, histologically conirmed m CRC, Eastern Coop?erative Oncology Group performance status 0–2, adequate organ function, and disease progression or intolerance of the irst?line regimen will be eligible. Patients will be randomized(1:1) to receive standard FOLFIRI with or with?out bevacizumab(5 mg/kg on day 1), repeated every 2 weeks(FOLIRI arm) or XELIRI with or without bevacizumab(7.5 mg/kg on day 1), repeated every 3 weeks(XELIRI arm). A total of 464 events were estimated as necessary to show non?inferiority with a power of 80% at a one?sided α of 0.025, requiring a target sample size of 600 patients. The 95% conidence interval(CI) upper limit of the hazard ratio was pre?speciied as less than 1.3.Conclusion: The Asian XELIRI Projec T is a multinational phase III trial being conducted to provide evidence for XELIRI with or without bevacizumab as a second?line treatment option of mCRC.
文摘In this study, the microstructure and second-phase particles in yttrium （0.05 wt.%and 0.8 wt.%） bearing Fe-10Ni-7Mn steels were characterized. The results of X-ray analysis as well as scanning electron microscopy coupled with energy dispersive X-ray spectroscopy indicated the formation of （Fe, Ni, Mn）17Y2 precipitates with hexagonal structure in a Fe-10Ni-7Mn-0.8Y （wt.%） alloy. Lattice parameters of these precipitates were calculated as follows：a=0.8485 nm and c=0.8274 nm. Formation of Y2O3 sub-micron particles was also confirmed in both yttrium bearing steels via electrolytic phase extraction method. The effect of these precipitates on the prior austenite grain size was investigated. The results revealed that these precipitates had an effective role in controlling the prior austenite grain size.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.91850107 and 12174116)the National Key Research and Development Program of China(Grant No.2018YFA0306200)+3 种基金Guangdong Innovative and Entrepreneurial Research Team Program(Grant No.2016ZT06C594)the Key Program of Guangzhou Scientific Research Special Project(Grant No.201904020013)the Science and Technology Project of Guangdong Province,China(Grant No.2020B010190001)the Fundamental Research Funds for the Central Universities。
文摘Here we propose a hybrid polymer-LN waveguide for achieving phase-matched second-harmonic generation(SHG).From the aspect of super-mode theory,the geometric parameters of the hybrid semi-nonlinear waveguide were optimized to utilize both symmetric(even)and antisymmetric(odd)modes of the pump and SHG waves so as to facilitate phase matching with large modal overlap.Phase matching between a fundamental even(TE_(00)-like)mode at 1320 nm and a fundamental odd(TE_(01)-like)mode at 660 nm was found with a calculated modal overlap integral of 0.299,while utilizing the largest nonlinear coefficient d_(33),and achieving an efficient calculated normalized conversion efficiency of 148%W^(-1)·cm^(-2).Considering the fabrication feasibility of such hybrid waveguide with features including etchless,large dimension,and low structural sensitivity,we believe our findings would provide a useful reference for future on-chip efficient nonlinear conversion devices.
