To solve the problem of difficult machining, the near-net shaped Al/SiCP composites with high volume fraction of SiC particles were fabricated by vacuum-pressure infiltration. The SiCP preform with a complex shape was...To solve the problem of difficult machining, the near-net shaped Al/SiCP composites with high volume fraction of SiC particles were fabricated by vacuum-pressure infiltration. The SiCP preform with a complex shape was prepared by gelcasting. Pure Al, Al4Mg, and Al4Mg2Si were used as the matrices, respectively. The results indicate that the optimal parameters of SiCP suspension in gelcasting process are pH value of 10, TMAH content of 0.5 wt.%, and solid loading of 52 vol.%. The Al matrix alloyed with Mg contributes to improving the interfacial wettability of the matrix and SiC particles, which increases the relative density of the composite. The Al matrix alloyed with Si is beneficial to inhibiting the formation of the detrimental Al4C3 phases. The Al4Mg2Si/SiCP composite exhibits high relative density of 99.2%, good thermal conductivity of 150 W·m^-1·K^-1, low coefficient of thermal expansion of 10.1×10^-6 K^-1, and excellent bending strength of 489 MPa.展开更多
The present work is focused on optimization of machining characteristics of AI/SiCp composites. The machining characteristics such as specific energy, tool wear and surface roughness were studied. The parameters such ...The present work is focused on optimization of machining characteristics of AI/SiCp composites. The machining characteristics such as specific energy, tool wear and surface roughness were studied. The parameters such as volume fraction of SiC, cutting speed and feed rate were considered. Artificial neural networks (ANN) was used to train and simulate the experimental data. Genetic algorithms (GA) was interfaced with ANN to optimize the machining conditions for the desired machining characteristics. Validation of optimized results was also performed by confirmation experiments.展开更多
SiCp-reinforced 6092Al composites with volume fractions of 25%and 60%were prepared using a powder metallurgy method.Their friction and wear characteristics were analyzed using a reciprocating friction and wear testing...SiCp-reinforced 6092Al composites with volume fractions of 25%and 60%were prepared using a powder metallurgy method.Their friction and wear characteristics were analyzed using a reciprocating friction and wear testing machine under loads of 20 to 50 N against YG6 cemented carbide.The experimental results show that the friction coefficients of all samples increase with increasing load.The 25vol%composite exhibits the lowest friction coefficient(0.1669-0.2716),while the 60vol%composite exhibits the highest(0.3237-0.3990),with the 6092 aluminum alloy falling between the two.The wear volume and specific wear rate also increase with load,but the composites with a higher Si C content demonstrate smaller increments,with the 60vol%composite exhibiting superior wear resistance.Under a 30 N load,the wear scars of the 60vol%composite show a significant increase in the contents of elements such as C,Co,W,and O,indicating more severe wear of the counterpart material.Scanning electron microscopy(SEM)reveals wear mechanisms including adhesive wear,two-body sliding and three-body rolling wear of particles,and delamination.展开更多
A new method was proposed for preparing AZ31/1060 composite plates with a corrugated interface,which involved cold-pressing a corrugated surface on the Al plate and then hot-pressing the assembled Mg/Al plate.The resu...A new method was proposed for preparing AZ31/1060 composite plates with a corrugated interface,which involved cold-pressing a corrugated surface on the Al plate and then hot-pressing the assembled Mg/Al plate.The results show that cold-pressing produces intense plastic deformation near the corrugated surface of the Al plate,which promotes dynamic recrystallization of the Al substrate near the interface during the subsequent hot-pressing.In addition,the initial corrugation on the surface of the Al plate also changes the local stress state near the interface during hot pressing,which has a large effect on the texture components of the substrates near the corrugated interface.The construction of the corrugated interface can greatly enhance the shear strength by 2−4 times due to the increased contact area and the strong“mechanical gearing”effect.Moreover,the mechanical properties are largely depended on the orientation relationship between corrugated direction and loading direction.展开更多
Inorganic materials can solve transportable and on-site hydrolytic hydrogen generation issues.CaH_(2)/(Al/Si)composites are preferable due to their notable chemical properties.However,these composites require pretreat...Inorganic materials can solve transportable and on-site hydrolytic hydrogen generation issues.CaH_(2)/(Al/Si)composites are preferable due to their notable chemical properties.However,these composites require pretreatments,an inert environment,and long hours of physical ball milling for high homogeneity and synergistic effects.CaH_(2)also inhibits the hydrolysis reaction by forming its products on the Al/Si surface,which hinders the direct utilization of composites.This work represents the first investigation of NaH-CaH_(2)(Al/Si)fuel composites,which greatly overcome these limitations and can be directly used for on-site hydrogen generation and proton exchange membrane(PEM)fuel cells.The NaH-CaH_(2)(Al/Si)fuel composites were prepared by using a straightforward mixing method with variable composition ratios,showing high H_(2)yield and fuel cell(FC)performance.NaH addition provides the bridge effect,which opens up a new way to enable efficient hydrolysis and greatly enhances the hydrolysis activity of CaH_(2)/(Al/Si)composites.The novel fuel composites(NaH-CaH_(2)/Al)have extraordinary FC performance and a 0.42 W/cm2 peak power density greater than commercial hydrogen generators.It provides high H_(2)yield 84.4%for NaH-CaH_(2)/Al and 82%for NaH-CaH_(2)/Si compared to NaOH-CaH_(2)(Al/Si),NaCl-CaH_(2)(Al/Si),and KCl-CaH_(2)(Al/Si)composites.The NaH bridge effect hinders the direct water contact and stops the formation of Ca(OH)2 around Al/Si,which provides adequate pathways for the CaH_(2)(Al/Si)hydrolysis.The impressive capabilities of novel fuel composites are anticipated to offer practical uses in fuel cells,automobile applications,and portable/on-board H_(2)generation.展开更多
SiC-reinforced aluminum matrix(SiCp/Al)composite is widely utilized in the aerospace,automotive,and electronics industries due to the combination of ceramic hardness and metal toughness.However,the significant dispari...SiC-reinforced aluminum matrix(SiCp/Al)composite is widely utilized in the aerospace,automotive,and electronics industries due to the combination of ceramic hardness and metal toughness.However,the significant disparity in properties between SiC particles and the aluminum matrix results in severe tool wear and diminished surface quality during conventional machining.This study proposes an environmentally friendly and clean dry electrical discharge assisted grinding process as an efficient and low-damage machining method for SiCp/Al.An experimental platform was set up to study the impact of grinding and discharge process parameters on surface quality.The study compared the chip formation mechanism and surface quality between dry electrical discharge assisted grinding and conventional grinding,revealing relationships between surface roughness,grinding force,grinding temperature,and related parameters.The results indicate that the proposed grinding method leads to smaller chip sizes,lower grinding forces and temperatures,and an average reduction of 19.2%in surface roughness compared to conventional grinding.The axial,tangential,and normal grinding forces were reduced by roughly 10.5%,37.8%,and 23.0%,respectively.The optimized process parameters were determined to be N=2500 r/min,vf=30 mm/min,a=10μm,E=15 V,f=5000 Hz,dc=80%,resulting in a surface roughness of 0.161μm.展开更多
Because of the challenge of compounding lightweight,high-strength Ti/Al alloys due to their considerable disparity in properties,Al 6063 as intermediate layer was proposed to fabricate TC4/Al 6063/Al 7075 three-layer ...Because of the challenge of compounding lightweight,high-strength Ti/Al alloys due to their considerable disparity in properties,Al 6063 as intermediate layer was proposed to fabricate TC4/Al 6063/Al 7075 three-layer composite plate by explosive welding.The microscopic properties of each bonding interface were elucidated through field emission scanning electron microscope and electron backscattered diffraction(EBSD).A methodology combining finite element method-smoothed particle hydrodynamics(FEM-SPH)and molecular dynamics(MD)was proposed for the analysis of the forming and evolution characteristics of explosive welding interfaces at multi-scale.The results demonstrate that the bonding interface morphologies of TC4/Al 6063 and Al 6063/Al 7075 exhibit a flat and wavy configuration,without discernible defects or cracks.The phenomenon of grain refinement is observed in the vicinity of the two bonding interfaces.Furthermore,the degree of plastic deformation of TC4 and Al 7075 is more pronounced than that of Al 6063 in the intermediate layer.The interface morphology characteristics obtained by FEM-SPH simulation exhibit a high degree of similarity to the experimental results.MD simulations reveal that the diffusion of interfacial elements predominantly occurs during the unloading phase,and the simulated thickness of interfacial diffusion aligns well with experimental outcomes.The introduction of intermediate layer in the explosive welding process can effectively produce high-quality titanium/aluminum alloy composite plates.Furthermore,this approach offers a multi-scale simulation strategy for the study of explosive welding bonding interfaces.展开更多
Plasma electrolytic oxidation(PEO)coatings were prepared on Al−Mg laminated macro composites(LMCs)using both unipolar and bipolar waveforms in an appropriate electrolyte for both aluminum and magnesium alloys.The tech...Plasma electrolytic oxidation(PEO)coatings were prepared on Al−Mg laminated macro composites(LMCs)using both unipolar and bipolar waveforms in an appropriate electrolyte for both aluminum and magnesium alloys.The techniques of FESEM/EDS,grazing incident beam X-ray diffraction(GIXRD),and electrochemical methods of potentiodynamic polarization and electrochemical impedance spectroscopy(EIS)were used to characterize the coatings.The results revealed that the coatings produced using the bipolar waveform exhibited lower porosity and higher thickness than those produced using the unipolar one.The corrosion performance of the specimens’cut edge was investigated using EIS after 1,8,and 12 h of immersion in a 3.5 wt.%NaCl solution.It was observed that the coating produced using the bipolar waveform demonstrated the highest corrosion resistance after 12 h of immersion,with an estimated corrosion resistance of 5.64 kΩ·cm^(2),which was approximately 3 times higher than that of the unipolar coating.Notably,no signs of galvanic corrosion were observed in the LMCs,and only minor corrosion attacks were observed on the magnesium layer in some areas.展开更多
The Mg−Al composite rods of aluminum core-reinforced magnesium alloy were prepared by the extrusion−shear(ES)process,and the microstructure,deformation mechanism,and mechanical properties of the Mg−Al composite rods w...The Mg−Al composite rods of aluminum core-reinforced magnesium alloy were prepared by the extrusion−shear(ES)process,and the microstructure,deformation mechanism,and mechanical properties of the Mg−Al composite rods were investigated at different extrusion temperatures and shear stresses.The experimental results show that the proportion of dynamic recrystallization(DRX)and texture for Al and Mg alloys are controlled by the combination of temperature and shear stress.The texture type of the Al alloys exhibits slight variations at different temperatures.With the increase of temperature,the DRX behavior of Mg alloy shifts from discontinuous DRX(DDRX),continuous DRX(CDRX),and twin-induced DRX(TDRX)dominant to CDRX,the dislocation density in Mg alloy grains decreases significantly,and the average value of Schmid factor(SF)of the basalslip system increases.In particular,partial grains exhibit a distinct dominant slip system at 390℃.The hardness and thickness of the bonding layer,as well as the yield strength and elongation of the Mg alloy,reach their maximum at 360℃as a result of the intricate influence of the combined temperature and shear stress.展开更多
Cu/Al composite plates were fabricated using rolling and underwater explosive welding techniques,separately,to compare their interfacial microstructures and mechanical performance.Interface morphology,grain orientatio...Cu/Al composite plates were fabricated using rolling and underwater explosive welding techniques,separately,to compare their interfacial microstructures and mechanical performance.Interface morphology,grain orientation,grain boundary characteristics,and phase distribution were analyzed through optical microscope,scanning electron microscope,and electron backscattered diffractometer.Mechanical properties were assessed using tensile shear tests,90°bending tests,and hardness measurements.Vickers hardness and nanoindentation test results further provided information on the hardness distributions.Results indicate that the diffusion layer in rolled Cu/Al composites is relatively fragile,while that produced by underwater explosive welding features a diffusion layer of approximately 18μm in thickness,which is metallurgically bonded through atomic diffusion.The tensile shear strength of these composites ranges from 64.45 MPa to 70.84 MPa,and in the 90°three-point bending test,the underwater-explosive-welded samples exhibit superior flexural performance.This study elucidates the effects of different manufacturing methods on the interfacial properties and mechanical performance of Cu/Al composites,offering essential insights for the selection of manufacturing methods and applications.展开更多
AZ31/Al/Ta composites were prepared using the vacuum hot compression bonding(VHCB)method.The effect of hot compressing temperature on the interface microstructure evolution,phase constitution,and shear strength at the...AZ31/Al/Ta composites were prepared using the vacuum hot compression bonding(VHCB)method.The effect of hot compressing temperature on the interface microstructure evolution,phase constitution,and shear strength at the interface was investigated.Moreover,the interface bonding mechanisms of the AZ31/Al/Ta composites during the VHCB process were explored.The results demonstrate that as the VHCB temperature increases,the phase composition of the interface between Mg and Al changes from the Mg-Al brittle intermetallic compounds(Al_(12)Mg_(17)and Al_(3)Mg_(2))to the Al-Mg solid solution.Meanwhile,the width of the Al/Ta interface diffusion layer at 450℃increases compared to that at 400℃.The shear strengths are 24 and 46 MPa at 400 and 450℃,respectively.The interfacial bonding mechanism of AZ31/Al/Ta composites involves the coexistence of diffusion and mechanical meshing.Avoiding the formation of brittle phases at the interface can significantly improve interfacial bonding strength.展开更多
In this study, liquid nitrogen was applied to grind SiCp/Al composites with high volume fraction and large SiC particle at different levels of cutting conditions, and the effects of grinding depth and speed on grindin...In this study, liquid nitrogen was applied to grind SiCp/Al composites with high volume fraction and large SiC particle at different levels of cutting conditions, and the effects of grinding depth and speed on grinding force, surface morphology, and surface roughness were investigated. At the same time, the effect of cryogenic cooling was also compared with that of conventional wet grinding. The experimental results indicated that cryogenic cooling is effective in enhancing supporting function of Al matrix to the SiC particles and improving surface quality. Additionally, the brittle fracture of SiC particles was suppressed and some ductile streaks on SiC particle could be observed.展开更多
Particle removal mechanism was presented during machining particle SiC/Al composites with diamond grinding tool. The relevant removal modes and their mechanisms were discussed considering the impact and squeezing effe...Particle removal mechanism was presented during machining particle SiC/Al composites with diamond grinding tool. The relevant removal modes and their mechanisms were discussed considering the impact and squeezing effect of diamond grit on the SiC particle. The experimental results show that the aluminum matrix has larger plastic deformation, so the aluminum mixed with the surplus SiC particles is cut from the surface. The SiC particles can be removed in multiple ways, such as broken/fractured, micro cracks, shearing and pulled out, etc. More particles removed by shearing, and less particles removed by fractured during material removal progress can produce a better machined surface.展开更多
The effects of SiCp surface modifications(Cu coating,Ni coating and Ni/Cu coating)on the microstructures and mechanical properties of Al matrix composites were investigated.Surface modification of SiC particles with C...The effects of SiCp surface modifications(Cu coating,Ni coating and Ni/Cu coating)on the microstructures and mechanical properties of Al matrix composites were investigated.Surface modification of SiC particles with Cu,Ni and Cu/Ni,respectively,was carried out by electroless plating method.SiCp/Al composites were prepared by hot pressed sintering followed by hot extrusion.The results show that the surface modification of SiC particles plays an effective role,which is relative to the type of surface coating,and the interfacial bonding become stronger in the following order:untreated SiCp<Ni(Cu)-coated SiCp<Ni/Cu-coated SiCp.The Ni/Cu-coated SiCp/Al composites exhibit the best comprehensive mechanical properties,with ultimate tensile strength(σUTS)and fracture strain(εf)of 389 MPa and 6.3%,respectively.Compared with that of untreated-SiCp/Al composites,theσUTS andεf are enhanced by 19.3%and 57.5%.展开更多
The aim of this work was to improve the properties of Ni-P coating on SiCp/Al composites. The effect of rare earths addition on Ni-P coating structure was investigated by means of scanning electron microscopy (SEM), e...The aim of this work was to improve the properties of Ni-P coating on SiCp/Al composites. The effect of rare earths addition on Ni-P coating structure was investigated by means of scanning electron microscopy (SEM), energy dispersive spectrometer (EDS), X-ray diffractometer (XRD) and electrochemistry methods. The results showed that as Y or La concentration was 0.15 g/L in plating solution, the highest value of deposition rate of Ni-P coating was found. And the structure of the obtained coating was modified...展开更多
This article studies the effects of the CeCl3 concentrations in conversion solutions with and without addition of NaCl, pH-values of conversion solution, drying temperature, time and temperature of immersion on the Ce...This article studies the effects of the CeCl3 concentrations in conversion solutions with and without addition of NaCl, pH-values of conversion solution, drying temperature, time and temperature of immersion on the Ce-conversion coatings for corrosion protection of the SiCp/5A06 Al-MMC and 5A06 Al-alloy in the 3.5% NaCl aqueous solution at room temperature. Potentiodynamic polarization tests reveal that the Ce-conversion treatment could markedly improve the pitting corrosion resistance of the composite and the matrix alloy in chloride containing environment. The best corrosion resistance effects are obtained for the samples treatment in 1% CeCl3.7H2O/3.5% NaCl solution at 45℃ for 60 min, followed by drying at 100 ℃ for 30 min. Examinations by means of scanning electron microscopy （SEM）, energy dispersion spectroscopy （EDS） and X-ray photoelectron spectroscopy （XPS） indicate that this behavior is due to the precipitation of Ce-oxides/hydroxides on the cathodic intermetallics and the Al-oxide film on the rest of the metal matrix.展开更多
Particle-tool interactions,which govern the synergetic deformation of SiC particle reinforced Al matrix composites under mechanical machining,strongly depend on the geometry of particle position residing on cutting pa...Particle-tool interactions,which govern the synergetic deformation of SiC particle reinforced Al matrix composites under mechanical machining,strongly depend on the geometry of particle position residing on cutting path.In the present work,we investigate the influence of cutting path on the machinability of a SiCp/Al composite in multi-step ultra-precision diamond cutting by combining finite element simulations with experimental observations and characterization.Be consistent with experimentally characterized microstructures,the simulated SiCp/Al composite is considered to be composed of randomly distributed polygonally-shaped SiC particles with a volume fraction of 25 vol%.A multi-step cutting strategy with depths of cut ranging from 2 to 10 lm is adopted to achieve an ultimate depth of cut of 10 lm.Intrinsic material parameters and extrinsic cutting conditions utilized in finite element simulations of SiCp/Al cutting are consistent with those used in corresponding experiments.Simulation results reveal different particle-tool interactions and failure modes of SiC particles,as well as their correlations with machining force evolution,residual stress distribution and machined surface topography.A detailed comparison between numerical simulation results and experimental data of multi-step diamond cutting of SiCp/Al composite reveals a substantial impact of the number of cutting steps on particle-tool interactions and machined surface quality.These findings provide guidelines for achieving high surface finish of SiCp/Al composites by ultra-precision diamond cutting.展开更多
SiCp/Al composites have excellent comprehensive properties and have been widely used in aerospace,automotive industry and other fields.Due to the huge difference in performance between SiC particles and matrix alloys,...SiCp/Al composites have excellent comprehensive properties and have been widely used in aerospace,automotive industry and other fields.Due to the huge difference in performance between SiC particles and matrix alloys,traditional fusion welding methods are difficult to meet the join requirements of SiCp/Al composites.Friction stir joining(friction stir welding),as a solid phase joining process,has been proved to be a new technology with fine prospect in joining SiCp/Al composites compared with fusion welding process.Although some progress has been made in recent years,there are still full of challenges.In this paper,the research status of friction stir joining of SiCp/Al composites in recent years is expatiated,including the weldability of SiCp/Al composites,the macrostructure and the microstructure of joints,mechanical properties of joints,and tool wear and monitoring.Furthermore,the existing challenges of friction stir joining of SiCp/Al composites are summarized and the future development directions are prospected.展开更多
基金Project (CXZZ20140506150310438) supported by the Science and Technology Program of Shenzhen City, ChinaProject (2017GK2261) supported by the Science and Technology Program of Hunan Province, ChinaProject (2017zzts111) supported by the Fundamental Research Funds for the Central Universities, China。
文摘To solve the problem of difficult machining, the near-net shaped Al/SiCP composites with high volume fraction of SiC particles were fabricated by vacuum-pressure infiltration. The SiCP preform with a complex shape was prepared by gelcasting. Pure Al, Al4Mg, and Al4Mg2Si were used as the matrices, respectively. The results indicate that the optimal parameters of SiCP suspension in gelcasting process are pH value of 10, TMAH content of 0.5 wt.%, and solid loading of 52 vol.%. The Al matrix alloyed with Mg contributes to improving the interfacial wettability of the matrix and SiC particles, which increases the relative density of the composite. The Al matrix alloyed with Si is beneficial to inhibiting the formation of the detrimental Al4C3 phases. The Al4Mg2Si/SiCP composite exhibits high relative density of 99.2%, good thermal conductivity of 150 W·m^-1·K^-1, low coefficient of thermal expansion of 10.1×10^-6 K^-1, and excellent bending strength of 489 MPa.
文摘The present work is focused on optimization of machining characteristics of AI/SiCp composites. The machining characteristics such as specific energy, tool wear and surface roughness were studied. The parameters such as volume fraction of SiC, cutting speed and feed rate were considered. Artificial neural networks (ANN) was used to train and simulate the experimental data. Genetic algorithms (GA) was interfaced with ANN to optimize the machining conditions for the desired machining characteristics. Validation of optimized results was also performed by confirmation experiments.
基金Funded by the Provincial Talent Project of Gansu Province(No.2025QNGR18)the Natural Science Foundation of Gansu Province(No.23JRRA1647)+2 种基金the"Qizhi"Talent Cultivation Project of Lanzhou Institute of Technology(No.2025QZ-02)the Education Science and Technology Innovation Project of Gansu Province(No.2025A-229)the Lanzhou Science and Technology Development Guidance Plan Project(No.2024-9-307)。
文摘SiCp-reinforced 6092Al composites with volume fractions of 25%and 60%were prepared using a powder metallurgy method.Their friction and wear characteristics were analyzed using a reciprocating friction and wear testing machine under loads of 20 to 50 N against YG6 cemented carbide.The experimental results show that the friction coefficients of all samples increase with increasing load.The 25vol%composite exhibits the lowest friction coefficient(0.1669-0.2716),while the 60vol%composite exhibits the highest(0.3237-0.3990),with the 6092 aluminum alloy falling between the two.The wear volume and specific wear rate also increase with load,but the composites with a higher Si C content demonstrate smaller increments,with the 60vol%composite exhibiting superior wear resistance.Under a 30 N load,the wear scars of the 60vol%composite show a significant increase in the contents of elements such as C,Co,W,and O,indicating more severe wear of the counterpart material.Scanning electron microscopy(SEM)reveals wear mechanisms including adhesive wear,two-body sliding and three-body rolling wear of particles,and delamination.
基金supported by Guangdong Major Project of Basic and Applied Basic Research, China (No. 2020B0301030006)Fundamental Research Funds for the Central Universities, China (No. SWU-XDJH202313)+1 种基金Chongqing Postdoctoral Science Foundation Funded Project, China (No. 2112012728014435)the Chongqing Postgraduate Research and Innovation Project, China (No. CYS23197)。
文摘A new method was proposed for preparing AZ31/1060 composite plates with a corrugated interface,which involved cold-pressing a corrugated surface on the Al plate and then hot-pressing the assembled Mg/Al plate.The results show that cold-pressing produces intense plastic deformation near the corrugated surface of the Al plate,which promotes dynamic recrystallization of the Al substrate near the interface during the subsequent hot-pressing.In addition,the initial corrugation on the surface of the Al plate also changes the local stress state near the interface during hot pressing,which has a large effect on the texture components of the substrates near the corrugated interface.The construction of the corrugated interface can greatly enhance the shear strength by 2−4 times due to the increased contact area and the strong“mechanical gearing”effect.Moreover,the mechanical properties are largely depended on the orientation relationship between corrugated direction and loading direction.
基金financial support granted by the National Natural Science Foundation of China (No. 22402225)the Gusu Innovation and Entrepreneurship Leading Talent Plan(No. ZXL2023193)+2 种基金the Sinano Talents Plan (No. 2022000175)the Guangdong Basic and Applied Basic Research Foundation (No.2023A1515111133)the ANSO Scholarship for Young Talents
文摘Inorganic materials can solve transportable and on-site hydrolytic hydrogen generation issues.CaH_(2)/(Al/Si)composites are preferable due to their notable chemical properties.However,these composites require pretreatments,an inert environment,and long hours of physical ball milling for high homogeneity and synergistic effects.CaH_(2)also inhibits the hydrolysis reaction by forming its products on the Al/Si surface,which hinders the direct utilization of composites.This work represents the first investigation of NaH-CaH_(2)(Al/Si)fuel composites,which greatly overcome these limitations and can be directly used for on-site hydrogen generation and proton exchange membrane(PEM)fuel cells.The NaH-CaH_(2)(Al/Si)fuel composites were prepared by using a straightforward mixing method with variable composition ratios,showing high H_(2)yield and fuel cell(FC)performance.NaH addition provides the bridge effect,which opens up a new way to enable efficient hydrolysis and greatly enhances the hydrolysis activity of CaH_(2)/(Al/Si)composites.The novel fuel composites(NaH-CaH_(2)/Al)have extraordinary FC performance and a 0.42 W/cm2 peak power density greater than commercial hydrogen generators.It provides high H_(2)yield 84.4%for NaH-CaH_(2)/Al and 82%for NaH-CaH_(2)/Si compared to NaOH-CaH_(2)(Al/Si),NaCl-CaH_(2)(Al/Si),and KCl-CaH_(2)(Al/Si)composites.The NaH bridge effect hinders the direct water contact and stops the formation of Ca(OH)2 around Al/Si,which provides adequate pathways for the CaH_(2)(Al/Si)hydrolysis.The impressive capabilities of novel fuel composites are anticipated to offer practical uses in fuel cells,automobile applications,and portable/on-board H_(2)generation.
基金Supported by National Natural Science Foundation of China(Grant Nos.52475480,51805334)Guangdong Basic and Applied Basic Research Foundation(Grant Nos.2023A1515030249,2023A1515110059)Shenzhen Science and Technology Program(Grant No.GJHZ20220913144212023).
文摘SiC-reinforced aluminum matrix(SiCp/Al)composite is widely utilized in the aerospace,automotive,and electronics industries due to the combination of ceramic hardness and metal toughness.However,the significant disparity in properties between SiC particles and the aluminum matrix results in severe tool wear and diminished surface quality during conventional machining.This study proposes an environmentally friendly and clean dry electrical discharge assisted grinding process as an efficient and low-damage machining method for SiCp/Al.An experimental platform was set up to study the impact of grinding and discharge process parameters on surface quality.The study compared the chip formation mechanism and surface quality between dry electrical discharge assisted grinding and conventional grinding,revealing relationships between surface roughness,grinding force,grinding temperature,and related parameters.The results indicate that the proposed grinding method leads to smaller chip sizes,lower grinding forces and temperatures,and an average reduction of 19.2%in surface roughness compared to conventional grinding.The axial,tangential,and normal grinding forces were reduced by roughly 10.5%,37.8%,and 23.0%,respectively.The optimized process parameters were determined to be N=2500 r/min,vf=30 mm/min,a=10μm,E=15 V,f=5000 Hz,dc=80%,resulting in a surface roughness of 0.161μm.
基金Opening Foundation of Key Laboratory of Explosive Energy Utilization and Control,Anhui Province(BP20240104)Graduate Innovation Program of China University of Mining and Technology(2024WLJCRCZL049)Postgraduate Research&Practice Innovation Program of Jiangsu Province(KYCX24_2701)。
文摘Because of the challenge of compounding lightweight,high-strength Ti/Al alloys due to their considerable disparity in properties,Al 6063 as intermediate layer was proposed to fabricate TC4/Al 6063/Al 7075 three-layer composite plate by explosive welding.The microscopic properties of each bonding interface were elucidated through field emission scanning electron microscope and electron backscattered diffraction(EBSD).A methodology combining finite element method-smoothed particle hydrodynamics(FEM-SPH)and molecular dynamics(MD)was proposed for the analysis of the forming and evolution characteristics of explosive welding interfaces at multi-scale.The results demonstrate that the bonding interface morphologies of TC4/Al 6063 and Al 6063/Al 7075 exhibit a flat and wavy configuration,without discernible defects or cracks.The phenomenon of grain refinement is observed in the vicinity of the two bonding interfaces.Furthermore,the degree of plastic deformation of TC4 and Al 7075 is more pronounced than that of Al 6063 in the intermediate layer.The interface morphology characteristics obtained by FEM-SPH simulation exhibit a high degree of similarity to the experimental results.MD simulations reveal that the diffusion of interfacial elements predominantly occurs during the unloading phase,and the simulated thickness of interfacial diffusion aligns well with experimental outcomes.The introduction of intermediate layer in the explosive welding process can effectively produce high-quality titanium/aluminum alloy composite plates.Furthermore,this approach offers a multi-scale simulation strategy for the study of explosive welding bonding interfaces.
文摘Plasma electrolytic oxidation(PEO)coatings were prepared on Al−Mg laminated macro composites(LMCs)using both unipolar and bipolar waveforms in an appropriate electrolyte for both aluminum and magnesium alloys.The techniques of FESEM/EDS,grazing incident beam X-ray diffraction(GIXRD),and electrochemical methods of potentiodynamic polarization and electrochemical impedance spectroscopy(EIS)were used to characterize the coatings.The results revealed that the coatings produced using the bipolar waveform exhibited lower porosity and higher thickness than those produced using the unipolar one.The corrosion performance of the specimens’cut edge was investigated using EIS after 1,8,and 12 h of immersion in a 3.5 wt.%NaCl solution.It was observed that the coating produced using the bipolar waveform demonstrated the highest corrosion resistance after 12 h of immersion,with an estimated corrosion resistance of 5.64 kΩ·cm^(2),which was approximately 3 times higher than that of the unipolar coating.Notably,no signs of galvanic corrosion were observed in the LMCs,and only minor corrosion attacks were observed on the magnesium layer in some areas.
基金supported by the general project of the National Natural Science Foundation of China(No.52071042)Chongqing Natural Science Foundation Project,China(Nos.CSTB2023NSCQ-MSX0079,cstc2021ycjh-bgzxm0148)Graduate Student Innovation Program of Chongqing University of Technology,China(No.gzlcx20232008).
文摘The Mg−Al composite rods of aluminum core-reinforced magnesium alloy were prepared by the extrusion−shear(ES)process,and the microstructure,deformation mechanism,and mechanical properties of the Mg−Al composite rods were investigated at different extrusion temperatures and shear stresses.The experimental results show that the proportion of dynamic recrystallization(DRX)and texture for Al and Mg alloys are controlled by the combination of temperature and shear stress.The texture type of the Al alloys exhibits slight variations at different temperatures.With the increase of temperature,the DRX behavior of Mg alloy shifts from discontinuous DRX(DDRX),continuous DRX(CDRX),and twin-induced DRX(TDRX)dominant to CDRX,the dislocation density in Mg alloy grains decreases significantly,and the average value of Schmid factor(SF)of the basalslip system increases.In particular,partial grains exhibit a distinct dominant slip system at 390℃.The hardness and thickness of the bonding layer,as well as the yield strength and elongation of the Mg alloy,reach their maximum at 360℃as a result of the intricate influence of the combined temperature and shear stress.
基金Anhui Province Key Research and Development Plan(2022a05020021)China Coal Science and Industry Group Chongqing Research Institute Independent Research and Development Project(2023YBXM58)。
文摘Cu/Al composite plates were fabricated using rolling and underwater explosive welding techniques,separately,to compare their interfacial microstructures and mechanical performance.Interface morphology,grain orientation,grain boundary characteristics,and phase distribution were analyzed through optical microscope,scanning electron microscope,and electron backscattered diffractometer.Mechanical properties were assessed using tensile shear tests,90°bending tests,and hardness measurements.Vickers hardness and nanoindentation test results further provided information on the hardness distributions.Results indicate that the diffusion layer in rolled Cu/Al composites is relatively fragile,while that produced by underwater explosive welding features a diffusion layer of approximately 18μm in thickness,which is metallurgically bonded through atomic diffusion.The tensile shear strength of these composites ranges from 64.45 MPa to 70.84 MPa,and in the 90°three-point bending test,the underwater-explosive-welded samples exhibit superior flexural performance.This study elucidates the effects of different manufacturing methods on the interfacial properties and mechanical performance of Cu/Al composites,offering essential insights for the selection of manufacturing methods and applications.
基金National Natural Science Foundation of China(52275308,52301146)Fundamental Research Funds for the Central Universities(2023JG007)Supported by Shi Changxu Innovation Center for Advanced Materials(SCXKFJJ202207)。
文摘AZ31/Al/Ta composites were prepared using the vacuum hot compression bonding(VHCB)method.The effect of hot compressing temperature on the interface microstructure evolution,phase constitution,and shear strength at the interface was investigated.Moreover,the interface bonding mechanisms of the AZ31/Al/Ta composites during the VHCB process were explored.The results demonstrate that as the VHCB temperature increases,the phase composition of the interface between Mg and Al changes from the Mg-Al brittle intermetallic compounds(Al_(12)Mg_(17)and Al_(3)Mg_(2))to the Al-Mg solid solution.Meanwhile,the width of the Al/Ta interface diffusion layer at 450℃increases compared to that at 400℃.The shear strengths are 24 and 46 MPa at 400 and 450℃,respectively.The interfacial bonding mechanism of AZ31/Al/Ta composites involves the coexistence of diffusion and mechanical meshing.Avoiding the formation of brittle phases at the interface can significantly improve interfacial bonding strength.
基金financially supported by the National Natural Science Foundation of China (No.50975184)
文摘In this study, liquid nitrogen was applied to grind SiCp/Al composites with high volume fraction and large SiC particle at different levels of cutting conditions, and the effects of grinding depth and speed on grinding force, surface morphology, and surface roughness were investigated. At the same time, the effect of cryogenic cooling was also compared with that of conventional wet grinding. The experimental results indicated that cryogenic cooling is effective in enhancing supporting function of Al matrix to the SiC particles and improving surface quality. Additionally, the brittle fracture of SiC particles was suppressed and some ductile streaks on SiC particle could be observed.
基金Funded by the National Natural Science Foundation of China(51505434)the Key Scientific and Technological Project of Henan Province(172102210547)the Program for Innovative Research Team in Science and Technology in University of Henan Province(18IRTSTHN015)
文摘Particle removal mechanism was presented during machining particle SiC/Al composites with diamond grinding tool. The relevant removal modes and their mechanisms were discussed considering the impact and squeezing effect of diamond grit on the SiC particle. The experimental results show that the aluminum matrix has larger plastic deformation, so the aluminum mixed with the surplus SiC particles is cut from the surface. The SiC particles can be removed in multiple ways, such as broken/fractured, micro cracks, shearing and pulled out, etc. More particles removed by shearing, and less particles removed by fractured during material removal progress can produce a better machined surface.
基金Project(2017zzts111)supported by the Fundamental Research Funds for the Central Universities,China。
文摘The effects of SiCp surface modifications(Cu coating,Ni coating and Ni/Cu coating)on the microstructures and mechanical properties of Al matrix composites were investigated.Surface modification of SiC particles with Cu,Ni and Cu/Ni,respectively,was carried out by electroless plating method.SiCp/Al composites were prepared by hot pressed sintering followed by hot extrusion.The results show that the surface modification of SiC particles plays an effective role,which is relative to the type of surface coating,and the interfacial bonding become stronger in the following order:untreated SiCp<Ni(Cu)-coated SiCp<Ni/Cu-coated SiCp.The Ni/Cu-coated SiCp/Al composites exhibit the best comprehensive mechanical properties,with ultimate tensile strength(σUTS)and fracture strain(εf)of 389 MPa and 6.3%,respectively.Compared with that of untreated-SiCp/Al composites,theσUTS andεf are enhanced by 19.3%and 57.5%.
基金Project supported by the National Natural Science Foundation of China (51004028)National Science and Technology Major Special Project (2009ZX04006-032)
文摘The aim of this work was to improve the properties of Ni-P coating on SiCp/Al composites. The effect of rare earths addition on Ni-P coating structure was investigated by means of scanning electron microscopy (SEM), energy dispersive spectrometer (EDS), X-ray diffractometer (XRD) and electrochemistry methods. The results showed that as Y or La concentration was 0.15 g/L in plating solution, the highest value of deposition rate of Ni-P coating was found. And the structure of the obtained coating was modified...
文摘This article studies the effects of the CeCl3 concentrations in conversion solutions with and without addition of NaCl, pH-values of conversion solution, drying temperature, time and temperature of immersion on the Ce-conversion coatings for corrosion protection of the SiCp/5A06 Al-MMC and 5A06 Al-alloy in the 3.5% NaCl aqueous solution at room temperature. Potentiodynamic polarization tests reveal that the Ce-conversion treatment could markedly improve the pitting corrosion resistance of the composite and the matrix alloy in chloride containing environment. The best corrosion resistance effects are obtained for the samples treatment in 1% CeCl3.7H2O/3.5% NaCl solution at 45℃ for 60 min, followed by drying at 100 ℃ for 30 min. Examinations by means of scanning electron microscopy （SEM）, energy dispersion spectroscopy （EDS） and X-ray photoelectron spectroscopy （XPS） indicate that this behavior is due to the precipitation of Ce-oxides/hydroxides on the cathodic intermetallics and the Al-oxide film on the rest of the metal matrix.
基金supports from the National Natural Science Foundation of China(NSFC)-German Research Foundation(DFG)International Joint Research Programme(51761135106)the Open Research Foundation of State Key Laboratory of Digital Manufacturing Equipment and Technology in Huazhong University of Science and Technology,China(DMETKF2019016)+1 种基金the Shandong Key R&D Program(2019GGX104027)the Fundamental Research Funds for the Central Universities。
文摘Particle-tool interactions,which govern the synergetic deformation of SiC particle reinforced Al matrix composites under mechanical machining,strongly depend on the geometry of particle position residing on cutting path.In the present work,we investigate the influence of cutting path on the machinability of a SiCp/Al composite in multi-step ultra-precision diamond cutting by combining finite element simulations with experimental observations and characterization.Be consistent with experimentally characterized microstructures,the simulated SiCp/Al composite is considered to be composed of randomly distributed polygonally-shaped SiC particles with a volume fraction of 25 vol%.A multi-step cutting strategy with depths of cut ranging from 2 to 10 lm is adopted to achieve an ultimate depth of cut of 10 lm.Intrinsic material parameters and extrinsic cutting conditions utilized in finite element simulations of SiCp/Al cutting are consistent with those used in corresponding experiments.Simulation results reveal different particle-tool interactions and failure modes of SiC particles,as well as their correlations with machining force evolution,residual stress distribution and machined surface topography.A detailed comparison between numerical simulation results and experimental data of multi-step diamond cutting of SiCp/Al composite reveals a substantial impact of the number of cutting steps on particle-tool interactions and machined surface quality.These findings provide guidelines for achieving high surface finish of SiCp/Al composites by ultra-precision diamond cutting.
基金supported by the National Natural Science Foundation of China(No.51675270)the Postgraduate Research&Practice Innovation Program of Jiangsu Province(No.KYCX17_0241)the China Postdoctoral Science Foundation(No.2016M600411)。
文摘SiCp/Al composites have excellent comprehensive properties and have been widely used in aerospace,automotive industry and other fields.Due to the huge difference in performance between SiC particles and matrix alloys,traditional fusion welding methods are difficult to meet the join requirements of SiCp/Al composites.Friction stir joining(friction stir welding),as a solid phase joining process,has been proved to be a new technology with fine prospect in joining SiCp/Al composites compared with fusion welding process.Although some progress has been made in recent years,there are still full of challenges.In this paper,the research status of friction stir joining of SiCp/Al composites in recent years is expatiated,including the weldability of SiCp/Al composites,the macrostructure and the microstructure of joints,mechanical properties of joints,and tool wear and monitoring.Furthermore,the existing challenges of friction stir joining of SiCp/Al composites are summarized and the future development directions are prospected.
