The effect of Bagasse ash （BAp） particle reinforcement on the wear behavior of Al-Cu- Mg alloy has been studied. Bagasse ash particles were varied from 0 wt pct-10 wt pct with interval of 2 wt pct. Unlubricated pin-...The effect of Bagasse ash （BAp） particle reinforcement on the wear behavior of Al-Cu- Mg alloy has been studied. Bagasse ash particles were varied from 0 wt pct-10 wt pct with interval of 2 wt pct. Unlubricated pin-on disc tests were conducted to examine the wear behaviour of the aluminium alloy/Bagasse ash particulate composites. The tests were conducted at varying loads, from 5 to 20 N and sliding speeds of 1.26 m/s, 2.51 m/s, 3.77 m/s and 5.02 m/s for a constant sliding distance of 5000 m. The results showed that the wear rates of the A1-Cu-Mg/BAp composites are lower than that of the matrix alloy and further decrease with increasing Bagasse ash content. Wear rate increases as the sliding speed and applied load increase. The microstructure of the worn surface revealed that a large amount of plastic deformation appeared on the surface of the unreinforced alloy. While Bagasse ash reinforced Al-Cu-Mg alloy showed worn out surface that is not smooth, and grooves, scratches and parallel lines were observed. A combination of adhesion and delamination wear was in operation. These results show that improve wear properties is achievable for the aluminium alloy by the addition of Bagasse ash particles as reinforcement material.展开更多
By means of ^（29）Si and ^（27）Al magic angle spinning nuclear magnetic resonance（MAS NMR） combined with deconvolution technique, X-ray diffraction（XRD）, scanning electron microscopy（SEM） as well as energy dis...By means of ^（29）Si and ^（27）Al magic angle spinning nuclear magnetic resonance（MAS NMR） combined with deconvolution technique, X-ray diffraction（XRD）, scanning electron microscopy（SEM） as well as energy dispersive X-ray system（EDX）, the effect of 5 wt% corrosive solutions（ viz. 5 wt% Na_2SO_4, MgSO_4, Na_2SO_^（4＋）Na Cl and Na_2SO_^（4＋）Na Cl＋Na_2CO_3） on C-S-H microstructure in portland cement containing 30 wt% fly ash was investigated.The results show that, in MgSO_4 solution, Mg2＋ promotes the decalcification of C-S-H by SO_4^（2-）,increasing silicate tetrahedra polymerization and mean chain length（MCL） of C-S-H. However, the substituting degree of Al^（3＋） for Si^（4＋）（Al[4]/Si） in the paste does not change evidently. Effect of Na_2SO_4 solution on C-S-H is not significantly influenced by Na Cl solution, while the MCL and Al[4]/Si of C-S-H in fly ashcement paste slightly change. However, the decalcification of C-S-H by SO_4^（2-） and CO_3^（2-） attack, as well as the activation of fly ash by SO_4^（2-） attack will increase the MCL and Al[4]/Si, which are both higher than that under Na_2SO_4 corrosion, MgSO_4 or Na_2SO_4 ＋Na Cl coordination corrosion.展开更多
文摘The effect of Bagasse ash （BAp） particle reinforcement on the wear behavior of Al-Cu- Mg alloy has been studied. Bagasse ash particles were varied from 0 wt pct-10 wt pct with interval of 2 wt pct. Unlubricated pin-on disc tests were conducted to examine the wear behaviour of the aluminium alloy/Bagasse ash particulate composites. The tests were conducted at varying loads, from 5 to 20 N and sliding speeds of 1.26 m/s, 2.51 m/s, 3.77 m/s and 5.02 m/s for a constant sliding distance of 5000 m. The results showed that the wear rates of the A1-Cu-Mg/BAp composites are lower than that of the matrix alloy and further decrease with increasing Bagasse ash content. Wear rate increases as the sliding speed and applied load increase. The microstructure of the worn surface revealed that a large amount of plastic deformation appeared on the surface of the unreinforced alloy. While Bagasse ash reinforced Al-Cu-Mg alloy showed worn out surface that is not smooth, and grooves, scratches and parallel lines were observed. A combination of adhesion and delamination wear was in operation. These results show that improve wear properties is achievable for the aluminium alloy by the addition of Bagasse ash particles as reinforcement material.
基金Funded by the Major State Basic Research Development Program of China(“973” Program)(No.2015CB655101)Natural Science Foundation of Hebei(No.E2016209283)+1 种基金National Natural Science Foundation of China(No.51402003)Open Foundation of Road Bridge and Structural Engineering Key Laboratory WHUT,China(No.DQZDJJ201504)
文摘By means of ^（29）Si and ^（27）Al magic angle spinning nuclear magnetic resonance（MAS NMR） combined with deconvolution technique, X-ray diffraction（XRD）, scanning electron microscopy（SEM） as well as energy dispersive X-ray system（EDX）, the effect of 5 wt% corrosive solutions（ viz. 5 wt% Na_2SO_4, MgSO_4, Na_2SO_^（4＋）Na Cl and Na_2SO_^（4＋）Na Cl＋Na_2CO_3） on C-S-H microstructure in portland cement containing 30 wt% fly ash was investigated.The results show that, in MgSO_4 solution, Mg2＋ promotes the decalcification of C-S-H by SO_4^（2-）,increasing silicate tetrahedra polymerization and mean chain length（MCL） of C-S-H. However, the substituting degree of Al^（3＋） for Si^（4＋）（Al[4]/Si） in the paste does not change evidently. Effect of Na_2SO_4 solution on C-S-H is not significantly influenced by Na Cl solution, while the MCL and Al[4]/Si of C-S-H in fly ashcement paste slightly change. However, the decalcification of C-S-H by SO_4^（2-） and CO_3^（2-） attack, as well as the activation of fly ash by SO_4^（2-） attack will increase the MCL and Al[4]/Si, which are both higher than that under Na_2SO_4 corrosion, MgSO_4 or Na_2SO_4 ＋Na Cl coordination corrosion.
