To make clear the influence of abrasive hardness on the erosion effect,the erosion experiments of abrasive air jet with the same impact energy were carried out.The influence of abrasive hardness on the erosion effect ...To make clear the influence of abrasive hardness on the erosion effect,the erosion experiments of abrasive air jet with the same impact energy were carried out.The influence of abrasive hardness on the erosion effect is clarified by comparing the different erosion depths.The main conclusions are as follows.Under the same mass flow rate and mesh number,the abrasive with a higher density needs greater pressure irrespective of hardness.After erosion damage,the abrasive size exhibits a Weibull distribution.The shape parameterβand Weibull distribution function of four types of abrasives are derived by the least squares method;moreover,βis found to have a quadratic relation with abrasive hardness.The results of the erosion experiments show that abrasive hardness and erosion depth are quadratically related.By calculating the increase in surface energy after abrasive erosion crushing,it is found that abrasive hardness has a quadratic relation with surface energy and that the increases in erosion depth and surface energy consumption are basically identical.In conclusion,the effect is a soft abrasive impact when the ratio of abrasive hardness(Ha)to the material hardness(Hm)is<2.6,and it is a hard abrasive impact when Ha/Hm>3.展开更多
The performance of a turbulent air jet impinging on a flat surface and subjected to cross flow is investigated.The study considers many different parameters,including Reynolds number Re,the normalized orifice-to-targe...The performance of a turbulent air jet impinging on a flat surface and subjected to cross flow is investigated.The study considers many different parameters,including Reynolds number Re,the normalized orifice-to-target spacing Z/D,and the ratioαof cross-flow to jet Reynolds numbers.As reported by other investigators,the optimum value of Z/D is 6.At this optimum Z/D,when the Reynolds number is raised from 5100 to 23000,the stagnation Nusselt number Nu increases by 150%.A correlation is proposed to estimate stagnation point heat transfer.Velocity profiles are used to examine the cooling characteristics of jets with and without cross flow.Cooling in both the upstream and downstream regions is estimated and compared with the performance of a jet without cross flow.For Z/D=6,the stagnation Nu decreases by 84%whenαis increased from 0 to 2.The corresponding decrease in the stagnation Nu for Z/D=2 is 75%.Cross flow significantly affects the flow pattern of fluid near the target surface,and anomalous flow behavior is observed in the stagnation region.Without cross flow,the radial velocity is close to zero at r/D=0,and the fluid velocity increases in the outward direction and attains a maximum value at r/D=1.With cross flow,the position of the peak velocity shifts.Average,stagnation point,and peak heat transfer coefficients are discussed in terms of the Stanton number.At low values ofα,there is an increase in the peak Nu.With cross flow,the location of the peak velocity changes.The augmentation in cooling in the downstream region and the reduction in cooling in the upstream region depend strongly on Z/D andα.For Z/D=2,atα=1,the average heat transfer downstream increases by 15%and the corresponding decrease upstream is 35%.展开更多
The Textile Technology Centre is the pride of Heberlein.State-of-the-art equipment and a team of top experts guarantee the highest standards of support for customers.Heberlein is the leading provider of air interlacin...The Textile Technology Centre is the pride of Heberlein.State-of-the-art equipment and a team of top experts guarantee the highest standards of support for customers.Heberlein is the leading provider of air interlacing and air texturing jets for synthetic continuous filament yarns and its clients enjoy added value in the form of practical help and guidance on textile processes and economic issues,with a special focus on filament yarn applications.展开更多
The present study focuses on the prediction of acoustic absorption performance of a perforated plate with air jets by theoretical calculations. In addition, we experimentally measured the flow rate, internal pressure,...The present study focuses on the prediction of acoustic absorption performance of a perforated plate with air jets by theoretical calculations. In addition, we experimentally measured the flow rate, internal pressure, acoustic pressure, and transfer function using an acoustic impedance tube. The normal incidence absorption coefficient was calculated from the measured transfer function using transfer function methods. We investigated the influences of background air space, flow velocity, thickness, aperture rate, and aperture diameter of a perforated plate on the acoustic absorption characteristics. The frequency characteristics of the acoustic absorption coefficient showed a maximum value at a local frequency. As the background air space increased, the peak frequency of acoustic absorption characteristics decreased. As the flow velocity passing through the apertures increased, the peak level of the acoustic absorption coefficient also increased. The theoretical results agreed well with the experimental ones qualitatively.展开更多
Shaoxing Shuifu Reeds is professional on producing all kinds of Air Jet Reeds and Flat Reeds,which has an annual output of 90,000 meters air-jet reeds,300,000,000 pcs of profile dents and 60,000 meters of Flat Reeds,W...Shaoxing Shuifu Reeds is professional on producing all kinds of Air Jet Reeds and Flat Reeds,which has an annual output of 90,000 meters air-jet reeds,300,000,000 pcs of profile dents and 60,000 meters of Flat Reeds,Which has been honored with China Air Jet Profile Reeds Research Center by China Textile Machinery Association in 2015.In order to reach the demands of high quality fabric and industrial textile products,the yarn is developing to high count,multicolor,various fibers,and the fabric is developing to high count,high density,environment protection.So we have researched out high density,multicolor,multinozzle,double energy saving type profile reeds to let you choose.展开更多
Jet ventilation is widely used in the ventilation design of highway and railway tunnels as an important air supply method during tunnel operation and disaster periods.This ventilation method has also been applied for ...Jet ventilation is widely used in the ventilation design of highway and railway tunnels as an important air supply method during tunnel operation and disaster periods.This ventilation method has also been applied for fire control in immersed tunnels.We conduct numerical simulations using computational fluid dynamics(CFD)to study positive ventilation in the upstream and reverse ventilation in the downstream(P-R)for an extra-wide immersed tunnel.The effects of fire source location and jet fan air velocity response strategy on the ceiling temperature decay,carbon monoxide(CO)distribution,and smoke exhaust efficiency were investigated for varying fire source locations.The results show that flames will be tilted to the side of the jet fan with a smaller air velocity.Additionally,the jet fan air velocity should be adjusted based on the relative distance between the fire source and the smoke vent.Among the studied scenarios,the most effective outcome was achieved when the air velocity was adjusted to 25 m/s on the side near the smoke vent.Also in this scenario,the phenomenon of smoke deposition was effectively mitigated and the average smoke exhaust efficiency reached 87%.Moreover,we found that the temperature decay of the tunnel follows an exponential decay law.The temperature decay rate is significantly higher on the side closest to the smoke vent compared to the farther side.This research provides a theoretical basis for smoke control strategies for fires that occur in immersed tunnels.展开更多
The effective smoke preventing installation should have the functions such as absolute smoke insulation, going into and coming off the smoke preventing place freely, no confinement of sight. The smoke preventing ai...The effective smoke preventing installation should have the functions such as absolute smoke insulation, going into and coming off the smoke preventing place freely, no confinement of sight. The smoke preventing air curtain is the most effective. Based on the previous researches done by others, the flow field is theoretically analyzed and the calculating method for the smoke preventing air curtain of high rise buildings is inferred by means of mathematics in this paper.展开更多
To study the draft sensation distribution of an air jet supply system in a large space building in summer,experiments are conducted in a large laboratory.The temperature,velocity and draft sensation distributions at a...To study the draft sensation distribution of an air jet supply system in a large space building in summer,experiments are conducted in a large laboratory.The temperature,velocity and draft sensation distributions at a nozzle height of 4 m in the occupied zone are obtained.Then,the numerical simulation under the test condition is carried out by the computational fluid dynamics（CFD）method.The calculation results of the indoor vertical temperature and the draft sensation distribution are validated by the test data.Simulations with different nozzle heights are conducted.The satisfactory air supply condition is determined by analyzing the draft sensations and the temperatures in the occupied zone under three conditions.The simulation results show that the optimal draft sensation distribution and the uniform temperature and velocity fields can be obtained at a nozzle height of 5 m.展开更多
In hot-dip galvanizing process, air jet wiping control is so crucial to decide the coating thickness and uni- formity of the zinc layer on the steel strip. The mathematical models developed predict the zinc coating th...In hot-dip galvanizing process, air jet wiping control is so crucial to decide the coating thickness and uni- formity of the zinc layer on the steel strip. The mathematical models developed predict the zinc coating thickness as a function of pressure and shear stress. The required pressure and shear stress profile on the strip surface were calcu- lated using regression analysis, and carried out using numerical simulation as FLUENT, a finite element analysis software. The influences of the outlet pressure, the nozzle to strip distance, the slot opening, the edge baffle plate, as well as the tilting angle of air knife were discussed. Combining with these results and regression analysis on the practical data, four first-order polynomial multi-parameter models were established for different targeted coating thicknesses with better regression coefficients. The validated model was used to carry out sensitivity analysis to de- termine the favorable controlling regime for the air jet wiping process.展开更多
Plasma synthetic jet actuator（PSJA） has a wide application prospect in the high-speed flow control field for its high jet velocity.In this paper,the influence of the air pressure on the performance of a two-electrod...Plasma synthetic jet actuator（PSJA） has a wide application prospect in the high-speed flow control field for its high jet velocity.In this paper,the influence of the air pressure on the performance of a two-electrode PSJA is investigated by the schlieren method in a large range from 7 k Pa to 100 k Pa.The energy consumed by the PSJA is roughly the same for all the pressure levels.Traces of the precursor shock wave velocity and the jet front velocity vary a lot for different pressures.The precursor shock wave velocity first decreases gradually and then remains at 345 m/s as the air pressure increases.The peak jet front velocity always appears at the first appearance of a jet,and it decreases gradually with the increase of the air pressure.A maximum precursor shock wave velocity of 520 m/s and a maximum jet front velocity of 440 m/s are observed at the pressure of 7 k Pa.The averaged jet velocity in one period ranges from 44 m/s to 54 m/s for all air pressures,and it drops with the rising of the air pressure.High velocities of the precursor shock wave and the jet front indicate that this type of PSJA can still be used to influence the high-speed flow field at 7 k Pa.展开更多
In this paper,the air plasma jet produced by micro-hollow cathode discharge(MHCD)is investigated.The discharge is powered by a positive nanosecond pulse high voltage supply.The waveforms of the discharge,the images of...In this paper,the air plasma jet produced by micro-hollow cathode discharge(MHCD)is investigated.The discharge is powered by a positive nanosecond pulse high voltage supply.The waveforms of the discharge,the images of the jet,the evolution of the plasma bullet and the reactive species are obtained to analyze the characteristics of the MHCD plasma jet.It is found that the length of the plasma jet is almost proportional to the air flow rate of 2–6 slm.Two plasma bullets appear one after another during a single period of the voltage waveform,and both of the two plasma bullets are formed during the positive pulse voltage off.The propagation velocity of the two plasma bullets is on the order of several hundred m/s,which is approximate to that of the air flow.These results indicate that the gas flow has an important influence on the formation of this MHCD plasma jet.展开更多
The half-dry cutting employs cryogenic compressed air cooled down to (10 to 40) and a micro-dosage of lubricating oil, called cryogenic cold air jet cutting was studied. On the basis of a comparative experiment on dr...The half-dry cutting employs cryogenic compressed air cooled down to (10 to 40) and a micro-dosage of lubricating oil, called cryogenic cold air jet cutting was studied. On the basis of a comparative experiment on dry and cryogenic cold air jet cuttings carried out for grade 45 steel, the effects of cryogenic cold air jet on the breaking of chips were discussed. The experimental results reveal that in the valid ranges of pressure and temperature, the cryogenic cold air jet widens the chip breaking areas effectively. When the cutting depth is not greater than 1 mm, the influence of chip breaking is much more significant. But different injecting angle of cold air has different influence on the chip-break. From the experiment, the optimized jet injecting angle, temperature effecting range and pressure working range of cold air are obtained. These results can offer a foundation for industrial manufacturing.展开更多
This article deals with the energy efficiency of textile weaving machines. A method based on exergy balances has been developed at the Institute for Textile Technology RWTH Aachen University （ITA）, Aachen, Germany i...This article deals with the energy efficiency of textile weaving machines. A method based on exergy balances has been developed at the Institute for Textile Technology RWTH Aachen University （ITA）, Aachen, Germany in order to improve energy efficiency textile machines. The relay nozzles of the air-jet weaving technology need up to 80% of the energy of the weaving machine. At ITA, a new nozzle concept was developed. The developed geometry is a so called High-Volume-Low-Pressure nozzle （HVLP nozzle）, based on convergent nozzle aerodynamic theory. With this concept, energy savings up to 30% are possible.展开更多
In order to investigate whether an air–water plasma jet is beneficial to improve the efficiency of inactivation, a series of experiments were done using a ring-needle plasma jet. The water content in the working gas...In order to investigate whether an air–water plasma jet is beneficial to improve the efficiency of inactivation, a series of experiments were done using a ring-needle plasma jet. The water content in the working gas（air） was accurately measured based on the Karl Fischer method. The effects of water on the production of OH（A;Σ;–X;Π;） and O（3p;P–3s;S） were also studied by optical emission spectroscopy. The results show that the water content is in the range of 2.53–9.58 mg l;, depending on the gas/water mixture ratio. The production of OH（A;Σ;–X;Π;） rises with the increase of water content, whereas the O（3p;P–3s;S） shows a declining tendency with higher water content. The sterilization experiments indicate that this air–water plasma jet inactivates the P. digitatum spores very effectively and its efficiency rises with the increase of the water content. It is possible that OH（A;Σ;–X;Π;） is a more effective species in inactivation than O（3p;P–3s;S） and the water content benefit the spore germination inhibition through rising the OH（A;Σ;–X;Π;） production. The maximum of the inactivation efficacy is up to 93% when the applied voltage is -6.75 kV and the water content is 9.58 mg l;.展开更多
JD Ceramics has been specializing in the field of air interlacing jets,air texturizing jets,and water jets over 29 years.With several years of technical accumulation and continuous equipments upgrades,we have been con...JD Ceramics has been specializing in the field of air interlacing jets,air texturizing jets,and water jets over 29 years.With several years of technical accumulation and continuous equipments upgrades,we have been consistently delivering high-precision,highquality,cost-effective ceramic nozzle solutions to the market.展开更多
The grading judgment for apples is related to a variety of factors including,size,shape,color,texture,and scars.Traditional manual sorting methods are time consuming and labor intensive.In addition,the accuracy of the...The grading judgment for apples is related to a variety of factors including,size,shape,color,texture,and scars.Traditional manual sorting methods are time consuming and labor intensive.In addition,the accuracy of the method is easily subjective,not repeatable,error-prone,and affected by the sorting environment.This paper presents a complete and automated grading system for apples.The system uses a single-chip microcomputer as the controller of the system,and a PC as the graphics processing unit.It also includes a conveyor,drive motor,frequency converter for motor control,photoelectric sensors,air compressor,and air jets for ejecting the graded apples.The classification algorithm is implemented by using a convolutional neural network(CNN).In order to eliminate contact damage of apples,the system specifically uses air jets as actuators to eject the graded apples into the corresponding bins.At the same time,in order to ensure that an apple triggers the correct ejecting actuator,this paper designs a jet controller with proper logic.展开更多
To overcome the drawbacks of the conventional foam technology used for dust suppression,including large pressure loss,high water pressure and low driving pressure,a new pneumatic foaming system is introduced.Then an o...To overcome the drawbacks of the conventional foam technology used for dust suppression,including large pressure loss,high water pressure and low driving pressure,a new pneumatic foaming system is introduced.Then an original design of foaming agent mixing device is proposed,and its performance is investigated and evaluated under different pressure compensations.Experimental results show that the maximum absorption amount increases by 2.9-6.7 times at a pressure compensation of 0.04-0.2 MPa compared with no pressure compensation.The pressure loss and pressure fluctuation both reduce significantly with increasing pressure compensation.The critical outlet pressure increases by30.4-240%.Field application indicates that the proposed mixing device ensures the reliable addition of foaming agent used for foam dust suppression.The effect of foam on dust suppression is remarkable,and the economic cost of foam is low.Therefore,there is reason to believe that the new mixing device will greatly promote foam technology to be widely used for suppressing dust in underground coal mines.展开更多
It is a challenge to polish the interior surface of an additively manufactured component with complex structures and groove sizes less than 1 mm.Traditional polishing methods are disabled to polish the component,meanw...It is a challenge to polish the interior surface of an additively manufactured component with complex structures and groove sizes less than 1 mm.Traditional polishing methods are disabled to polish the component,meanwhile keeping the structure intact.To overcome this challenge,small-grooved components made of aluminum alloy with sizes less than 1 mm were fabricated by a custom-made printer.A novel approach to multi-phase jet(MPJ)polishing is proposed,utilizing a self-developed polisher that incorporates solid,liquid,and gas phases.In contrast,abrasive air jet(AAJ)polishing is recommended,employing a customized polisher that combines solid and gas phases.After jet polishing,surface roughness(Sa)on the interior surface of grooves decreases from pristine 8.596μm to 0.701μm and 0.336μm via AAJ polishing and MPJ polishing,respectively,and Sa reduces 92%and 96%,correspondingly.Furthermore,a formula defining the relationship between linear energy density and unit defect volume has been developed.The optimized parameters in additive manufacturing are that linear energy density varies from 0.135 J mm^(-1)to 0.22 J mm^(-1).The unit area defect volume achieved via the optimized parameters decreases to 1/12 of that achieved via non-optimized ones.Computational fluid dynamics simulation results reveal that material is removed by shear stress,and the alumina abrasives experience multiple collisions with the defects on the heat pipe groove,resulting in uniform material removal.This is in good agreement with the experimental results.The novel proposed setups,approach,and findings provide new insights into manufacturing complex-structured components,polishing the small-grooved structure,and keeping it unbroken.展开更多
This paper presents fluid mechanics of ventilation system formed by the momentum source and the buoyancy source,which investigates inter-action between the plume and the non-isothermal air jet since buoyancy source is...This paper presents fluid mechanics of ventilation system formed by the momentum source and the buoyancy source,which investigates inter-action between the plume and the non-isothermal air jet since buoyancy source is produced by the plume and momentum source is generated by the air jet,respectively. The interaction is discussed by a mathematical model,an idealized situation of the plume rising from a point heat source of buoyancy alone-in particular the initial momentum flux at the source is zero. Furthermore,the paper discusses the effects of the parameters such as strength of source,air-flow volume and air-flow velocity used in the mathematical-physical model. Considering the effect of the plume generated by the indoor heat source,one expression of trajectory of the non-isothermal air jet produced by jet diffuser is deduced. And field-experiment has also been carried out to illustrate the effect on flowing-action of the air jet and validate the theoretical work. It can be concluded that the heat sources do have effect on the flowing-action of the air jet,and the effect mainly depends on the interaction produced by the plume and the air jet. The results show that the thermal buoyant effect of plumes on the air jet should be taken into account if the indoor heat sources are large enough. Numerical simulation is conducted and coincides with the experimental results as well.展开更多
基金Projects(51704096,51574112)supported by the National Natural Science Foundation of ChinaProject(192102310236)supported by the Key Scientific and Technological Project of Henan Province,China+2 种基金Project(2019M662496)supported by Postdoctoral Science Foundation of ChinaProject(2017YFC0804209)supported by the National Key Research and Development Program of ChinaProject(J2018-4)supported by the Science Research Funds for the Universities of Henan Province,China
文摘To make clear the influence of abrasive hardness on the erosion effect,the erosion experiments of abrasive air jet with the same impact energy were carried out.The influence of abrasive hardness on the erosion effect is clarified by comparing the different erosion depths.The main conclusions are as follows.Under the same mass flow rate and mesh number,the abrasive with a higher density needs greater pressure irrespective of hardness.After erosion damage,the abrasive size exhibits a Weibull distribution.The shape parameterβand Weibull distribution function of four types of abrasives are derived by the least squares method;moreover,βis found to have a quadratic relation with abrasive hardness.The results of the erosion experiments show that abrasive hardness and erosion depth are quadratically related.By calculating the increase in surface energy after abrasive erosion crushing,it is found that abrasive hardness has a quadratic relation with surface energy and that the increases in erosion depth and surface energy consumption are basically identical.In conclusion,the effect is a soft abrasive impact when the ratio of abrasive hardness(Ha)to the material hardness(Hm)is<2.6,and it is a hard abrasive impact when Ha/Hm>3.
文摘The performance of a turbulent air jet impinging on a flat surface and subjected to cross flow is investigated.The study considers many different parameters,including Reynolds number Re,the normalized orifice-to-target spacing Z/D,and the ratioαof cross-flow to jet Reynolds numbers.As reported by other investigators,the optimum value of Z/D is 6.At this optimum Z/D,when the Reynolds number is raised from 5100 to 23000,the stagnation Nusselt number Nu increases by 150%.A correlation is proposed to estimate stagnation point heat transfer.Velocity profiles are used to examine the cooling characteristics of jets with and without cross flow.Cooling in both the upstream and downstream regions is estimated and compared with the performance of a jet without cross flow.For Z/D=6,the stagnation Nu decreases by 84%whenαis increased from 0 to 2.The corresponding decrease in the stagnation Nu for Z/D=2 is 75%.Cross flow significantly affects the flow pattern of fluid near the target surface,and anomalous flow behavior is observed in the stagnation region.Without cross flow,the radial velocity is close to zero at r/D=0,and the fluid velocity increases in the outward direction and attains a maximum value at r/D=1.With cross flow,the position of the peak velocity shifts.Average,stagnation point,and peak heat transfer coefficients are discussed in terms of the Stanton number.At low values ofα,there is an increase in the peak Nu.With cross flow,the location of the peak velocity changes.The augmentation in cooling in the downstream region and the reduction in cooling in the upstream region depend strongly on Z/D andα.For Z/D=2,atα=1,the average heat transfer downstream increases by 15%and the corresponding decrease upstream is 35%.
文摘The Textile Technology Centre is the pride of Heberlein.State-of-the-art equipment and a team of top experts guarantee the highest standards of support for customers.Heberlein is the leading provider of air interlacing and air texturing jets for synthetic continuous filament yarns and its clients enjoy added value in the form of practical help and guidance on textile processes and economic issues,with a special focus on filament yarn applications.
基金supported by JSPS KAKENHI Grant Numbers JP17K06232
文摘The present study focuses on the prediction of acoustic absorption performance of a perforated plate with air jets by theoretical calculations. In addition, we experimentally measured the flow rate, internal pressure, acoustic pressure, and transfer function using an acoustic impedance tube. The normal incidence absorption coefficient was calculated from the measured transfer function using transfer function methods. We investigated the influences of background air space, flow velocity, thickness, aperture rate, and aperture diameter of a perforated plate on the acoustic absorption characteristics. The frequency characteristics of the acoustic absorption coefficient showed a maximum value at a local frequency. As the background air space increased, the peak frequency of acoustic absorption characteristics decreased. As the flow velocity passing through the apertures increased, the peak level of the acoustic absorption coefficient also increased. The theoretical results agreed well with the experimental ones qualitatively.
文摘Shaoxing Shuifu Reeds is professional on producing all kinds of Air Jet Reeds and Flat Reeds,which has an annual output of 90,000 meters air-jet reeds,300,000,000 pcs of profile dents and 60,000 meters of Flat Reeds,Which has been honored with China Air Jet Profile Reeds Research Center by China Textile Machinery Association in 2015.In order to reach the demands of high quality fabric and industrial textile products,the yarn is developing to high count,multicolor,various fibers,and the fabric is developing to high count,high density,environment protection.So we have researched out high density,multicolor,multinozzle,double energy saving type profile reeds to let you choose.
文摘Jet ventilation is widely used in the ventilation design of highway and railway tunnels as an important air supply method during tunnel operation and disaster periods.This ventilation method has also been applied for fire control in immersed tunnels.We conduct numerical simulations using computational fluid dynamics(CFD)to study positive ventilation in the upstream and reverse ventilation in the downstream(P-R)for an extra-wide immersed tunnel.The effects of fire source location and jet fan air velocity response strategy on the ceiling temperature decay,carbon monoxide(CO)distribution,and smoke exhaust efficiency were investigated for varying fire source locations.The results show that flames will be tilted to the side of the jet fan with a smaller air velocity.Additionally,the jet fan air velocity should be adjusted based on the relative distance between the fire source and the smoke vent.Among the studied scenarios,the most effective outcome was achieved when the air velocity was adjusted to 25 m/s on the side near the smoke vent.Also in this scenario,the phenomenon of smoke deposition was effectively mitigated and the average smoke exhaust efficiency reached 87%.Moreover,we found that the temperature decay of the tunnel follows an exponential decay law.The temperature decay rate is significantly higher on the side closest to the smoke vent compared to the farther side.This research provides a theoretical basis for smoke control strategies for fires that occur in immersed tunnels.
文摘The effective smoke preventing installation should have the functions such as absolute smoke insulation, going into and coming off the smoke preventing place freely, no confinement of sight. The smoke preventing air curtain is the most effective. Based on the previous researches done by others, the flow field is theoretically analyzed and the calculating method for the smoke preventing air curtain of high rise buildings is inferred by means of mathematics in this paper.
基金The National Natural Science Foundation of China(No.50478113)the Leading Academic Discipline Project of Shanghai Municipal Education Commission(No.J50502)
文摘To study the draft sensation distribution of an air jet supply system in a large space building in summer,experiments are conducted in a large laboratory.The temperature,velocity and draft sensation distributions at a nozzle height of 4 m in the occupied zone are obtained.Then,the numerical simulation under the test condition is carried out by the computational fluid dynamics（CFD）method.The calculation results of the indoor vertical temperature and the draft sensation distribution are validated by the test data.Simulations with different nozzle heights are conducted.The satisfactory air supply condition is determined by analyzing the draft sensations and the temperatures in the occupied zone under three conditions.The simulation results show that the optimal draft sensation distribution and the uniform temperature and velocity fields can be obtained at a nozzle height of 5 m.
基金Sponsored by National Natural Science Foundation of China (50604006)National Development and Reform Commission of China (2009-354)
文摘In hot-dip galvanizing process, air jet wiping control is so crucial to decide the coating thickness and uni- formity of the zinc layer on the steel strip. The mathematical models developed predict the zinc coating thickness as a function of pressure and shear stress. The required pressure and shear stress profile on the strip surface were calcu- lated using regression analysis, and carried out using numerical simulation as FLUENT, a finite element analysis software. The influences of the outlet pressure, the nozzle to strip distance, the slot opening, the edge baffle plate, as well as the tilting angle of air knife were discussed. Combining with these results and regression analysis on the practical data, four first-order polynomial multi-parameter models were established for different targeted coating thicknesses with better regression coefficients. The validated model was used to carry out sensitivity analysis to de- termine the favorable controlling regime for the air jet wiping process.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.51407197,51522606,51336011,91541120,and 11472306)
文摘Plasma synthetic jet actuator（PSJA） has a wide application prospect in the high-speed flow control field for its high jet velocity.In this paper,the influence of the air pressure on the performance of a two-electrode PSJA is investigated by the schlieren method in a large range from 7 k Pa to 100 k Pa.The energy consumed by the PSJA is roughly the same for all the pressure levels.Traces of the precursor shock wave velocity and the jet front velocity vary a lot for different pressures.The precursor shock wave velocity first decreases gradually and then remains at 345 m/s as the air pressure increases.The peak jet front velocity always appears at the first appearance of a jet,and it decreases gradually with the increase of the air pressure.A maximum precursor shock wave velocity of 520 m/s and a maximum jet front velocity of 440 m/s are observed at the pressure of 7 k Pa.The averaged jet velocity in one period ranges from 44 m/s to 54 m/s for all air pressures,and it drops with the rising of the air pressure.High velocities of the precursor shock wave and the jet front indicate that this type of PSJA can still be used to influence the high-speed flow field at 7 k Pa.
基金supported by National Natural Science Foundation of China(No.11475019)。
文摘In this paper,the air plasma jet produced by micro-hollow cathode discharge(MHCD)is investigated.The discharge is powered by a positive nanosecond pulse high voltage supply.The waveforms of the discharge,the images of the jet,the evolution of the plasma bullet and the reactive species are obtained to analyze the characteristics of the MHCD plasma jet.It is found that the length of the plasma jet is almost proportional to the air flow rate of 2–6 slm.Two plasma bullets appear one after another during a single period of the voltage waveform,and both of the two plasma bullets are formed during the positive pulse voltage off.The propagation velocity of the two plasma bullets is on the order of several hundred m/s,which is approximate to that of the air flow.These results indicate that the gas flow has an important influence on the formation of this MHCD plasma jet.
文摘The half-dry cutting employs cryogenic compressed air cooled down to (10 to 40) and a micro-dosage of lubricating oil, called cryogenic cold air jet cutting was studied. On the basis of a comparative experiment on dry and cryogenic cold air jet cuttings carried out for grade 45 steel, the effects of cryogenic cold air jet on the breaking of chips were discussed. The experimental results reveal that in the valid ranges of pressure and temperature, the cryogenic cold air jet widens the chip breaking areas effectively. When the cutting depth is not greater than 1 mm, the influence of chip breaking is much more significant. But different injecting angle of cold air has different influence on the chip-break. From the experiment, the optimized jet injecting angle, temperature effecting range and pressure working range of cold air are obtained. These results can offer a foundation for industrial manufacturing.
文摘This article deals with the energy efficiency of textile weaving machines. A method based on exergy balances has been developed at the Institute for Textile Technology RWTH Aachen University （ITA）, Aachen, Germany in order to improve energy efficiency textile machines. The relay nozzles of the air-jet weaving technology need up to 80% of the energy of the weaving machine. At ITA, a new nozzle concept was developed. The developed geometry is a so called High-Volume-Low-Pressure nozzle （HVLP nozzle）, based on convergent nozzle aerodynamic theory. With this concept, energy savings up to 30% are possible.
基金supported by National Natural Science Foundation of China (NSFC) under Grants No. 51407020National Key Technology Research and Development Program of the Ministry of Science and Technology of China under Grants No. 2014BAC13B05Visiting Scholarship of State Key Laboratory of Power Transmission Equipment & System Security and New Technology (Chongqing University) No. 2007DA10512716404
文摘In order to investigate whether an air–water plasma jet is beneficial to improve the efficiency of inactivation, a series of experiments were done using a ring-needle plasma jet. The water content in the working gas（air） was accurately measured based on the Karl Fischer method. The effects of water on the production of OH（A;Σ;–X;Π;） and O（3p;P–3s;S） were also studied by optical emission spectroscopy. The results show that the water content is in the range of 2.53–9.58 mg l;, depending on the gas/water mixture ratio. The production of OH（A;Σ;–X;Π;） rises with the increase of water content, whereas the O（3p;P–3s;S） shows a declining tendency with higher water content. The sterilization experiments indicate that this air–water plasma jet inactivates the P. digitatum spores very effectively and its efficiency rises with the increase of the water content. It is possible that OH（A;Σ;–X;Π;） is a more effective species in inactivation than O（3p;P–3s;S） and the water content benefit the spore germination inhibition through rising the OH（A;Σ;–X;Π;） production. The maximum of the inactivation efficacy is up to 93% when the applied voltage is -6.75 kV and the water content is 9.58 mg l;.
文摘JD Ceramics has been specializing in the field of air interlacing jets,air texturizing jets,and water jets over 29 years.With several years of technical accumulation and continuous equipments upgrades,we have been consistently delivering high-precision,highquality,cost-effective ceramic nozzle solutions to the market.
文摘The grading judgment for apples is related to a variety of factors including,size,shape,color,texture,and scars.Traditional manual sorting methods are time consuming and labor intensive.In addition,the accuracy of the method is easily subjective,not repeatable,error-prone,and affected by the sorting environment.This paper presents a complete and automated grading system for apples.The system uses a single-chip microcomputer as the controller of the system,and a PC as the graphics processing unit.It also includes a conveyor,drive motor,frequency converter for motor control,photoelectric sensors,air compressor,and air jets for ejecting the graded apples.The classification algorithm is implemented by using a convolutional neural network(CNN).In order to eliminate contact damage of apples,the system specifically uses air jets as actuators to eject the graded apples into the corresponding bins.At the same time,in order to ensure that an apple triggers the correct ejecting actuator,this paper designs a jet controller with proper logic.
基金supported by the National Natural Science Foundation of China(Nos.51474216 and 51504249)the Priority Academic Program Development of Jiangsu Higher Education Institutions(PAPD)the Fundamental Research Funds for theCentral Universities
文摘To overcome the drawbacks of the conventional foam technology used for dust suppression,including large pressure loss,high water pressure and low driving pressure,a new pneumatic foaming system is introduced.Then an original design of foaming agent mixing device is proposed,and its performance is investigated and evaluated under different pressure compensations.Experimental results show that the maximum absorption amount increases by 2.9-6.7 times at a pressure compensation of 0.04-0.2 MPa compared with no pressure compensation.The pressure loss and pressure fluctuation both reduce significantly with increasing pressure compensation.The critical outlet pressure increases by30.4-240%.Field application indicates that the proposed mixing device ensures the reliable addition of foaming agent used for foam dust suppression.The effect of foam on dust suppression is remarkable,and the economic cost of foam is low.Therefore,there is reason to believe that the new mixing device will greatly promote foam technology to be widely used for suppressing dust in underground coal mines.
基金the National Key Research and Development Program of China(2018YFA0703400)the Young Scientists Fund of the National Natural Science Foundation of China(52205447)Changjiang Scholars Program of the Chinese Ministry of Education。
文摘It is a challenge to polish the interior surface of an additively manufactured component with complex structures and groove sizes less than 1 mm.Traditional polishing methods are disabled to polish the component,meanwhile keeping the structure intact.To overcome this challenge,small-grooved components made of aluminum alloy with sizes less than 1 mm were fabricated by a custom-made printer.A novel approach to multi-phase jet(MPJ)polishing is proposed,utilizing a self-developed polisher that incorporates solid,liquid,and gas phases.In contrast,abrasive air jet(AAJ)polishing is recommended,employing a customized polisher that combines solid and gas phases.After jet polishing,surface roughness(Sa)on the interior surface of grooves decreases from pristine 8.596μm to 0.701μm and 0.336μm via AAJ polishing and MPJ polishing,respectively,and Sa reduces 92%and 96%,correspondingly.Furthermore,a formula defining the relationship between linear energy density and unit defect volume has been developed.The optimized parameters in additive manufacturing are that linear energy density varies from 0.135 J mm^(-1)to 0.22 J mm^(-1).The unit area defect volume achieved via the optimized parameters decreases to 1/12 of that achieved via non-optimized ones.Computational fluid dynamics simulation results reveal that material is removed by shear stress,and the alumina abrasives experience multiple collisions with the defects on the heat pipe groove,resulting in uniform material removal.This is in good agreement with the experimental results.The novel proposed setups,approach,and findings provide new insights into manufacturing complex-structured components,polishing the small-grooved structure,and keeping it unbroken.
基金Sponsored by the National Natural Science Foundation of China (Grant No 50478113)the Key Project of Shanghai Education Committee (Grant NoJ50502)Special Research Fund in Shanghai Colleges and Universities to Select and Train Outstanding Young Teachers (Grant No slg09011)
文摘This paper presents fluid mechanics of ventilation system formed by the momentum source and the buoyancy source,which investigates inter-action between the plume and the non-isothermal air jet since buoyancy source is produced by the plume and momentum source is generated by the air jet,respectively. The interaction is discussed by a mathematical model,an idealized situation of the plume rising from a point heat source of buoyancy alone-in particular the initial momentum flux at the source is zero. Furthermore,the paper discusses the effects of the parameters such as strength of source,air-flow volume and air-flow velocity used in the mathematical-physical model. Considering the effect of the plume generated by the indoor heat source,one expression of trajectory of the non-isothermal air jet produced by jet diffuser is deduced. And field-experiment has also been carried out to illustrate the effect on flowing-action of the air jet and validate the theoretical work. It can be concluded that the heat sources do have effect on the flowing-action of the air jet,and the effect mainly depends on the interaction produced by the plume and the air jet. The results show that the thermal buoyant effect of plumes on the air jet should be taken into account if the indoor heat sources are large enough. Numerical simulation is conducted and coincides with the experimental results as well.
