Although Ziegler-Natta(Z-N)polyolefins have been widely used as raw materials to produce pharmaceutical or food packaging,the migration of acid scavengers,an additive usually introduced in Z-N polyolefins,from the pac...Although Ziegler-Natta(Z-N)polyolefins have been widely used as raw materials to produce pharmaceutical or food packaging,the migration of acid scavengers,an additive usually introduced in Z-N polyolefins,from the packaging to its contents has not been reported.In this work,the migration of the two most used acid scavengers,calcium stearate(CaSt_(2))and zinc stearate(ZnSt_(2)),from a Z-N polypropylene random copolymer(PPR)into water during autoclaving at 121℃ were comparatively investigated.It was found that,for PPR plates containing 0.1 wt%CaSt_(2)or ZnSt_(2)(PPR-0.1CaSt_(2),PPR-0.1ZnSt_(2),respectively),the concentration of migrated calcium ion into water increased with autoclaving time,while that of zinc ion was much lower at same treatment durations and did not show a significant increase with treatment time.Interestingly,after removing all plates and acidification treatment,a considerable amount of stearic acid was detected in sterilized water for PPR-0.1ZnSt_(2),but no such significant stearic acid was detected in sterilized water for PPR-0.1CaSt_(2).Based on the structural evolution of the two soaps upon heating,possible mechanisms for the different migration behavior of CaSt_(2)and ZnSt_(2)from PPR into water during autoclaving treatment were proposed.Our results suggest that the migration issue of acid scavengers is worthy of attention in pharmaceutical packaging materials produced from Z-N polyolefins.展开更多
The effect of sonication pretreatment condition on Eucheuma cottonii and Gelidium amansii seaweed towards agar extraction wae studied.Four parameters were changed during sonication to investigate the effects on agar y...The effect of sonication pretreatment condition on Eucheuma cottonii and Gelidium amansii seaweed towards agar extraction wae studied.Four parameters were changed during sonication to investigate the effects on agar yield and quality.These parameters include the time interval,concentration ratio,frequency,and intensity.The highest amount of agar extracted from Eucheuma cottonii species could be obtained from the time interval of 30min,seaweed weight to solvent volume ratio of 1:20,the frequency of 35Hz,and the sonication power intensity of 30%.For Gelidium amansii species,the best agar yield also could be obtained from the time interval of 30 min,1:20 of seaweed weight to water volume ratio,the frequency of 35Hz,and power intensity of 30%.From the experiment,sonication pretreatment signifi cantly influenced the yield and properties of extracted agar.The sonication with autoclaved seaweed produced agar containing less sulfate content,which is an excellent chemical property for gel electrophoresis applications.The gelstrength of sonication with autoclaving for both seaweeds,Eucheuma and Gelidium species was the highest among those by sonication with direct heating,which proved that sonication pretreatment with autoclaving could enhance the physical properties of the agar.展开更多
Besides being employed as an efficient plant growth retardant for field, garden and potted plants, paclobutrazol (PBZ) is also used in laboratory experiments, mainly in aseptic cultures, both in autoclaved and non-aut...Besides being employed as an efficient plant growth retardant for field, garden and potted plants, paclobutrazol (PBZ) is also used in laboratory experiments, mainly in aseptic cultures, both in autoclaved and non-autoclaved form. Therefore it is not known if autoclaving can partial or completely inactivates the product, thus decreasing its efficacy. Thus a simple experiment was carried out to assess to what extent the autoclaving process can affect some growth components and dry mass accumulation and partition in sunflower seedlings, by employing the techniques of plant Growth Analysis. Autoclaving did not modify either qualitative or quantitatively any of the plant responses to PBZ as well their reversions by gibberellic acid.展开更多
It has been widely recognized that the mixing process has significant impacts on the performance of low-density polyethylene(LDPE)reactors due to the rapid radical polymerization occurred in the reactors,but how the m...It has been widely recognized that the mixing process has significant impacts on the performance of low-density polyethylene(LDPE)reactors due to the rapid radical polymerization occurred in the reactors,but how the macro-and micro-mixing affect the reactor performance was still controversial in publications.In this work,a cold-flow LDPE autoclave with multi-feedings was scaled down(1/2)from an industrial reactor and built to systematically investigate the macro-and micro-mixing characteristics of fluid by experiments.Furthermore,the effects of macro-and micro-mixing on the polymerization were comprehensively analyzed.The results showed that according to the delay time t_(d) and macro-mixing times tM calculated from residence time distribution(RTD)curves,the macro-mixing states are significantly different at various axial positions(h/H),especially at lower agitation Reynolds number Re.But with the increase of Re,since the circulation flow in the reactor is strengthened,the t_(d) for each feed gradually decreases to 0,and the t_(M) at different axial positions tend to be identical.For micro-mixing,the qualities of micro-mixing at different axial positions are similar,and the average micro-mixing time t_(m) in the reactor decreases exponentially with the increase of Re.Moreover,a fitting model was established.Through the comparison of the characteristic times of macro-mixing(t_(d),t_(M)),micro-mixing(t_(m))and elementary reactions within the industrial range of Re,it can be concluded that the properties of LDPE products are dominated by the macro-mixing behavior,and the consumption of initiators is affected by both the macro-and micro-mixing behaviors.This conclusion is of great significance for the design,optimization and operation of LDPE reactors.展开更多
In view of the volume instability of steel slag aggregate leading to the quality problem of expansion damage in asphalt road construction,the 4.75-9.5 mm steel slag particles were treated by autoclaved carbonation tec...In view of the volume instability of steel slag aggregate leading to the quality problem of expansion damage in asphalt road construction,the 4.75-9.5 mm steel slag particles were treated by autoclaved carbonation technology,and the effects of the carbonation system(temperature and time)on the autoclaved pulverization rate,f-CaO content,and the relationship between them for the carbonated steel slag were investigated.In addition,the microstructure of the carbonated steel slag was analyzed by X-ray diffractometer(XRD),scanning electron microscope and energy dispersive spectrometer(SEM-EDS),metallographic microscope and X-ray fluorescence imaging spectrometer(XRF).The experimental results indicate that,under the initial CO_(2)pressure of 1.0 MPa,increasing the carbonation temperature leads to the increase in the crystal plane spacing of Ca(OH)_(2)that was generated by the hydration of minerals in steel slag,and promotes the transformation of carbonated CaCO_(3)from the orthorhombic system to the hexagonal system,resulting in the increase of the crystal planes spacing of them,meantime,accelerates the decomposition of RO phases and also the outward migration of Ca^(2+),Fe^(2+),and Mn^(2+)ions to cover and coat on the Si^(4+),Al^(3+)ions,and impels the formation of hydroxides such as Fe(OH)_(3)and the formation of carbonates such as Ca(Mg)CO_(3),FeCO_(3)and MnCO_(3).Carbonation at the temperature of 90℃for 3 h can reach the center of 4.75-9.5 mm steel slag particles.Meanwhile,the increase of temperature can promote the mineral reaction in steel slag,resulting in the fuzzy interface between mineral phases,increase of burrs,dispersion,crossover,reduction of grain size,and rearrangement of mineral particles.展开更多
Objectives: There is a risk of spreading infectious material via non-sterile impressions. The aim of this study was to compare the effect of autoclave sterilisation on dimensional stability and tear strength of impres...Objectives: There is a risk of spreading infectious material via non-sterile impressions. The aim of this study was to compare the effect of autoclave sterilisation on dimensional stability and tear strength of impression materials. Methods: Twenty-four specimens were produced using a standard ruled test block for each of three impression materials (Affinis, Aquasil and Speedex) to test dimensional stability. Thirty tear strips for each material were prepared for the tear test (ISO 34-1). Specimens were randomly allocated to 3 different groups (autoclaved, disinfected or untreated). A non-contact scanner was used to analyse dimensional change and a universal testing machine was used to determine tear strengths. Results: There were no significant differences in the test dimensions measured for any of the three impression materials following autoclave treatment compared to the disinfected or untreated control groups. The tear strengths were not adversely affected by autoclave sterilisation at 134°C. Conclusion: These addition and condensation-cured silicone impression materials can be steam autoclaved without adverse effects on dimensional accuracy or tear strength.展开更多
AIM:To evaluate the effect of autoclaved diet on the jejunum neurons of the myenteric plexus of rats during their growth.METHODS:The experimental groups were made up of rats going through weaning whose mothers receive...AIM:To evaluate the effect of autoclaved diet on the jejunum neurons of the myenteric plexus of rats during their growth.METHODS:The experimental groups were made up of rats going through weaning whose mothers received either an autoclaved or a non-autoclaved diet during gestation and lactation,and rats that were fed the same diet as their mothers during the post-weaning period.In order to measure the neurons'body profile and to quantify the number of neurons per area,preparations were stained by the nicotinamide adenine dinucleotide-diaphorase method.RESULTS:No significant changes were observed in rats'body weight or in the number of neurons regardless of the diet used(P>0.05) .There was a decrease in the jejunum-ileum length in rats treated with an autoclaved diet(P<0.05) .An increase in the neuronal cross-sectional area was seen in rats that had received the autoclaved diet,an effect that was significant for animals undergoing weaning.In addition,all observed factors showed significant differences when related to the age of the animals.CONCLUSION:The autoclaved diet did not alter the quantity of neurons,but increased their cell body area,suggesting changes similar to those observed in protein deficiency.展开更多
Autoclaved aerated concrete(AAC) panels have ultra-light weight,excellent thermal insulation and energy absorption,so it is an ideal building material for protective structures.To improve the blast resistance of the A...Autoclaved aerated concrete(AAC) panels have ultra-light weight,excellent thermal insulation and energy absorption,so it is an ideal building material for protective structures.To improve the blast resistance of the AAC panels,three schemes are applied to strengthen the AAC panels through spraying 4 mm thick polyurea coating from top,bottom and double-sides.In three-point bending tests,the polyurea-coated AAC panels have much higher ultimate loads than the un-coated panels,but slightly lower than those strengthened by the carbon fiber reinforced plastics(CEFRPs).Close-in explosion experiments reveal the dynamic strengthening effect of the polyurea coating.Critical scaled distances of the strengthened AAC panels are acquired,which are valuable for the engineering application of the AAC panels in the extreme loading conditions.Polyurea coatings efficiently enhance the blast resistance of the bottom and double-sided polyurea-coated AAC panels.It is interesting that the polyurea-coated AAC panels have much more excellent blast resistance than the CFRP reinforced AAC panels,although the latter have better static mechanical properties.展开更多
Suitable methods for enhancing the volume stability of steel slag utilized as fine aggregate were determined. The effects of steam treatment at 100 ℃ and autoclave treatment under 2.0 MPa on the soundness of steel sl...Suitable methods for enhancing the volume stability of steel slag utilized as fine aggregate were determined. The effects of steam treatment at 100 ℃ and autoclave treatment under 2.0 MPa on the soundness of steel slag sand were investigated by means of powder ratio, linear expansion, compressive and flexural strength. DTA, EDX, XRD and ethylene glycol methods were employed to analyze both the treated slags and susceptible expansion grains. Experimental results indicate that powder ratio, content of free lime and rate of linear expansion can express the improvement in volume stability of different treated methods. Steam treatment process cannot ultimately prevent specimens from cracking and decrease of strength, but mortar made from autoclave treated slag keeps integration subjected to hot water of 80℃ until 28 d and its strength do not show significant decrement. The hydration of over-burn free lime and periclase phase are the main cause for the disintegration or crack of untreated and steam treated steel slag＇s specimens. Autoclave treatment process is more effective than steam treatment process on enhancement of volume stability of steel slag.展开更多
Nd-Fe-B permanent magnets doped with CuZn5 powders were prepared via conventional sintered method. The effects of CuZn5 contents on magnetic properties and corrosion resistance of the magnets were sys- tematically stu...Nd-Fe-B permanent magnets doped with CuZn5 powders were prepared via conventional sintered method. The effects of CuZn5 contents on magnetic properties and corrosion resistance of the magnets were sys- tematically studied. It shows that the remanence, coercivity, and maximum energy product decrease gradually with the increase in CuZn5 doping content. The magnet＇s corrosion kinetics in autoclaves environment and its electrochemical properties in electrolytes were also examined. It is interesting to see that the weight loss of 3.5 wt% and 4.5 wt% CuZn5 powders doping magnets is only 1 and 0 mg.cm^-2 after autoclaves test at 121 ℃, 2 × 10^5 Pa for 500 h, respectively, which is much lower than that of the magnets without CuZn5 doping. Electrochemical results show that the CuZn5 powders doping magnets display more positive corrosion potential （Eoorr） and lower corrosion current density （Icorr） than those of the original magnets without CuZn5 doping in sulphuric acid electrolyte and distilled water. It is, therefore, concluded that doping CuZn5 powders is a promising way to enhance the corrosion resistance of sintered Nd-Fe-B magnets.展开更多
Synthesis of autoclaved aerated concrete （AAC） has been carried out with carbide slag addition, and the carbide slag could be used as a main material to produce the AAC with the compressive strength about 2 MPa and ...Synthesis of autoclaved aerated concrete （AAC） has been carried out with carbide slag addition, and the carbide slag could be used as a main material to produce the AAC with the compressive strength about 2 MPa and the density below 0.6 g.cm-3. In this study, quartz sand acted as frame structure phase in the matrix, and quartz addition also influenced the Si/Ca of starting material. Tobermorite and CSH gel were formed readily at 62%, which seemed to enhance the compressive strength of samples. Curing time seemed to affect the morphology of phase produced, and specimen with the plate-like tobermorite formed at 10 h appeared to have a better compressive strength development than the fiber-like one at 18 h. The higher curing temperature seemed to favor the tobermorite and CSH gel formation, which also exerted a significant effect on the strength development of the samples. On the micro-scale, the formed CSH gel was filled in the interface of the matrix, and the tobermorite appeared to grow in internal-surface of the pores and interstices. The tobermorite or/and CSH formation seemed to densify the matrix, and therefore enhanced the strength of the samples.展开更多
The leaching behavior of a copper flotation concentrate was investigated using ammonium persulfate （APS） in an autoclave systee. The decomposition products of APS, active oxygen, and acidic medium were used to extra...The leaching behavior of a copper flotation concentrate was investigated using ammonium persulfate （APS） in an autoclave systee. The decomposition products of APS, active oxygen, and acidic medium were used to extract metals from the concentrate. Leaching experiments were performed to compare the availability of APS as an oxidizing agent for leaching of the concentrate under atmospheric conditions and in an autoclave system. Leaching temperature and APS concentration were found to be important parameters in both leaching systems. Atmospheric leaching studies showed that the metal extractions increased with the increase in APS concentration and temperature （up to 333 K）. A similar tendency was determined in the autoclave studies up to 423 K. It was also determined that the metal extractions decreased at temperatures above 423 K due to the passivation of the particle surface by molten elemental sulfur. The results showed that higher copper extractions could be achieved using an autoclave system.展开更多
Decomposition experiments conducted with and without microbial processes are commonly used to study the effects of environmental microorganisms on the degradation of organic pollutants.However,the effects of biologica...Decomposition experiments conducted with and without microbial processes are commonly used to study the effects of environmental microorganisms on the degradation of organic pollutants.However,the effects of biological pretreatment （sterilization） on organic matter often have a negative impact on such experiments.Based on the principle of water total organic carbon （TOC） analysis,the effects of physical sterilization treatments on determination of TOC and other water quality parameters were investigated.The results revealed that two conventional physical sterilization treatments,autoclaving and 60 Co γ-radiation sterilization,led to the direct decomposition of some organic pollutants,resulting in remarkable errors in the analysis of TOC in water samples.Furthermore,the extent of the errors varied with the intensity and the duration of sterilization treatments.Accordingly,a novel sterilization method for water samples,0.45 μm micro-filtration coupled with ultraviolet radiation （MCUR）,was developed in the present study.The results indicated that the MCUR method was capable of exerting a high bactericidal effect on the water sample while significantly decreasing the negative impact on the analysis of TOC and other water quality parameters.Before and after sterilization treatments,the relative errors of TOC determination could be controlled to lower than 3% for water samples with different categories and concentrations of organic pollutants by using MCUR.展开更多
The multiphase reaction process of pressure leaching is mainly carried out in the liquid phase. Therefore, gas holdup is essential for the gas–liquid–solid phase reaction and the extraction rate of valuable metals. ...The multiphase reaction process of pressure leaching is mainly carried out in the liquid phase. Therefore, gas holdup is essential for the gas–liquid–solid phase reaction and the extraction rate of valuable metals. In this paper, a transparent quartz autoclave, a six blades disc turbine-type agitator, and a high-speed camera were used to investigate the gas holdup of the pressure leaching process. Furthermore, experiments determining the effects of agitation rate, temperature, and oxygen partial pressure on gas holdup were carried out. The results showed that when the agitation rate increased from 350 to 600 r/min, the gas holdup increased from 0.10% to 0.64%. When the temperature increased from 363 to 423 K, the gas holdup increased from 0.14% to 0.20%. When the oxygen partial pressure increased from 0.1 to 0.8 MPa, the gas holdup increased from 0.13% to 0.19%. A similar criteria relationship was established by Homogeneous Principle and Buckingham's theorem. Comprehensively, empirical equation of gas holdup was deduced on the basis of experimental data and the similarity theory, where the criterion equation was determined as ε=4.54×10^(-11)n^(3.65)T^(2.08)P_g^(0.18). It can be seen from the formula that agitation rate made the most important impact on gas holdup in the pressure leaching process using the mixed-flow agitator.展开更多
Autoclaved aerated concrete(AAC)has become more attractive due to its excellent and environmental-friendly properties in building construction.AAC is relatively lightweight,possesses lower thermal conductivity,higher ...Autoclaved aerated concrete(AAC)has become more attractive due to its excellent and environmental-friendly properties in building construction.AAC is relatively lightweight,possesses lower thermal conductivity,higher heat resistance,lower shrinkage,and fasten construction than normal concrete.AAC is a combination of silica sand,cement,gypsum,lime,water,and an expansion agent.To improve its physical and mechanical properties and reduce its production cost,tremendous innovations where waste materials were utilized as partial replacement of AAC materials were done.This paper is intended to present the literature on the utilization of waste materials as a means of a partial replacement in AAC materials to enhance its physical and mechanical properties and thermal performance.The physical properties such as microstructure and mechanical properties such as density,compressive strength,water absorption are presented to classify the investigation that has been done in such innovations.Apart from that,the discussion on innovations to improve its thermal performance was also presented.Based on the review,an increase of AAC application causes much waste at construction sites and recycling concrete waste powder into wall concrete;particularly,an AAC was not frequently practiced in construction.展开更多
A novel solvothermal synthesis method for the direct growth of B-form crystals of copper phthalocyanine（CuPc） is presented in this article. With quinoline as solvent, crystals were grown after cooling the reaction m...A novel solvothermal synthesis method for the direct growth of B-form crystals of copper phthalocyanine（CuPc） is presented in this article. With quinoline as solvent, crystals were grown after cooling the reaction mixture of 1,3-diiminoisoindoline and copper oxide, heated for 9 h at 270 ℃, to room temperature in an autoclave. These high quality crystals were suitable for characterization measurements. The single-crystal diffraction data show a monoclinic system unit cell： a=1.4668（3） nm, b=0.48109（10） nm, c=1.9515（7） nm, a=90°, B=121.04（2）°, r=90°, where the corresponding cell volume is 1.17991 nm^3. Needle-like single crystals of CuPc up to 10.5 mm in length were obtained. The influences of different temperatures, reaction time and solvent volume on the crystal yields were also discussed. Optimum reaction conditions were 10 mL of quinoline, at 270 ℃ for 8 h.展开更多
Due to the important scientific significance of the interaction between alkaline feldspar and high-temperature and high-pressure fluids. We have conducted a series of autoclave experiments of feldspar dissolution and ...Due to the important scientific significance of the interaction between alkaline feldspar and high-temperature and high-pressure fluids. We have conducted a series of autoclave experiments of feldspar dissolution and secondary mineral precipitation in conditions of 250–500℃, 8-50 MPa, and pH = 3.0 and 5.5. Based on the interaction experiments between alkaline feldspar and fluid of high-temperatures and high-pressures, we get the main results as follows:(1) The law that people have grasped below the critical point about the influence of temperature, pressure, and pH value on the alkaline feldspar dissolution behavior is still held above the critical point.(2) Due to the experimental techniques of autoclave flip 180°—sharp quenching and based on electron microprobe analysis of mineral new formed, theoretical analysis has determined that the new altered minerals distributed on the island dissolution surface of feldspar are products of precipitation on a feldspar surface after saturation of the relative ion concentration in water fluid.展开更多
The influence of poly（methylmethacrylate-co-N-vinyl-2-pyrrolidone）, P（MMA-co-VP）, on corrosion of carbon steels（J55, N80, P110 SS and C110 steels） in 3.5 wt% NaCl solution saturated with CO2 was evaluated using ...The influence of poly（methylmethacrylate-co-N-vinyl-2-pyrrolidone）, P（MMA-co-VP）, on corrosion of carbon steels（J55, N80, P110 SS and C110 steels） in 3.5 wt% NaCl solution saturated with CO2 was evaluated using static high pressure and high temperature（HPHT） autoclave. The surface was further evaluated by X-ray diffraction（XRD）, scanning electron microscopy（SEM） and contact angle measurements. Quantum chemical calculations have been used to evaluate the structural, electronic and reactivity parameters of the inhibitor on the steels surface. SEM, XRD and contact angle measurement studies reveal that the surface of metals are quite unaffected after use of inhibitor in 3.5% NaCl solution saturated with CO2.展开更多
We developed a set of in-situ Micro-Raman spectroscopy system for autoclave experimental apparatus because of the scientific significance of in-situ Micro-Raman spectroscopy system under the high-pressure hydrothermal...We developed a set of in-situ Micro-Raman spectroscopy system for autoclave experimental apparatus because of the scientific significance of in-situ Micro-Raman spectroscopy system under the high-pressure hydrothermal condition.We used this system to measure the Raman spectrum of water-fluid and quartz crystal at the temperature ranging from 125 to 420℃.The signal-tonoise ratio of the Raman signal is good.展开更多
We aimed to reuse the propylene oxide sludge(POS).Propylene oxide sludge shell-aggregate(POSS-A)and propylene oxide sludge gradient shell-aggregate(POSGS-A)whose main hydrated phase is tobermorite were successfully ma...We aimed to reuse the propylene oxide sludge(POS).Propylene oxide sludge shell-aggregate(POSS-A)and propylene oxide sludge gradient shell-aggregate(POSGS-A)whose main hydrated phase is tobermorite were successfully manufactured by the hydrothermal synthesis of POS and silica materials under the condition of autoclaved(180℃,1.0 MPa)curing.Influences of pre-wetting time of coarse aggregate and pressure application mode on the different concretes were investigated.The experimental results show that the concrete with POSS-A as coarse aggregate(POSS-A concrete),the concrete with POS gradient shell-aggregate as coarse aggregate(POSGS-A concrete),sintered aggregate concrete and common concrete,all have excellent impermeability performance whatever the pre-wetting time of coarse aggregate is 0.5 h or 24 h,and the pre-wetting time of coarse aggregate has a negligible influence on the concrete.The influence degree of pressure application mode on the impermeability performance of the sintered aggregate concrete is the greatest among three kinds of concrete,which has a negligible influence on impermeability performance of the other concretes.POSGS-A can be used as a green building light aggregate in hydraulic concrete.展开更多
基金supported by the National Natural Science Foundation of China(No.52173056)the Science and Technology Program of Gansu Province,China(No.23ZDGA001).
文摘Although Ziegler-Natta(Z-N)polyolefins have been widely used as raw materials to produce pharmaceutical or food packaging,the migration of acid scavengers,an additive usually introduced in Z-N polyolefins,from the packaging to its contents has not been reported.In this work,the migration of the two most used acid scavengers,calcium stearate(CaSt_(2))and zinc stearate(ZnSt_(2)),from a Z-N polypropylene random copolymer(PPR)into water during autoclaving at 121℃ were comparatively investigated.It was found that,for PPR plates containing 0.1 wt%CaSt_(2)or ZnSt_(2)(PPR-0.1CaSt_(2),PPR-0.1ZnSt_(2),respectively),the concentration of migrated calcium ion into water increased with autoclaving time,while that of zinc ion was much lower at same treatment durations and did not show a significant increase with treatment time.Interestingly,after removing all plates and acidification treatment,a considerable amount of stearic acid was detected in sterilized water for PPR-0.1ZnSt_(2),but no such significant stearic acid was detected in sterilized water for PPR-0.1CaSt_(2).Based on the structural evolution of the two soaps upon heating,possible mechanisms for the different migration behavior of CaSt_(2)and ZnSt_(2)from PPR into water during autoclaving treatment were proposed.Our results suggest that the migration issue of acid scavengers is worthy of attention in pharmaceutical packaging materials produced from Z-N polyolefins.
基金Supported by the University of Malaya under Equitable Society Research Cluster(ESRC)(No.GC002A-15SBS)
文摘The effect of sonication pretreatment condition on Eucheuma cottonii and Gelidium amansii seaweed towards agar extraction wae studied.Four parameters were changed during sonication to investigate the effects on agar yield and quality.These parameters include the time interval,concentration ratio,frequency,and intensity.The highest amount of agar extracted from Eucheuma cottonii species could be obtained from the time interval of 30min,seaweed weight to solvent volume ratio of 1:20,the frequency of 35Hz,and the sonication power intensity of 30%.For Gelidium amansii species,the best agar yield also could be obtained from the time interval of 30 min,1:20 of seaweed weight to water volume ratio,the frequency of 35Hz,and power intensity of 30%.From the experiment,sonication pretreatment signifi cantly influenced the yield and properties of extracted agar.The sonication with autoclaved seaweed produced agar containing less sulfate content,which is an excellent chemical property for gel electrophoresis applications.The gelstrength of sonication with autoclaving for both seaweeds,Eucheuma and Gelidium species was the highest among those by sonication with direct heating,which proved that sonication pretreatment with autoclaving could enhance the physical properties of the agar.
基金Thanks are due to FAPEMIG(Foundation for Research Sponsoring of Minas Gerais State)for the scholarships granted to DMR(Post-Doctoral training),JB and GBR(Scientific Initiation training)and for the financial support in several occasions.
文摘Besides being employed as an efficient plant growth retardant for field, garden and potted plants, paclobutrazol (PBZ) is also used in laboratory experiments, mainly in aseptic cultures, both in autoclaved and non-autoclaved form. Therefore it is not known if autoclaving can partial or completely inactivates the product, thus decreasing its efficacy. Thus a simple experiment was carried out to assess to what extent the autoclaving process can affect some growth components and dry mass accumulation and partition in sunflower seedlings, by employing the techniques of plant Growth Analysis. Autoclaving did not modify either qualitative or quantitatively any of the plant responses to PBZ as well their reversions by gibberellic acid.
基金the support and encouragement of the Key Projects of the Ministry of Industry and Information Technology of China(TC220A04W-3,188)。
文摘It has been widely recognized that the mixing process has significant impacts on the performance of low-density polyethylene(LDPE)reactors due to the rapid radical polymerization occurred in the reactors,but how the macro-and micro-mixing affect the reactor performance was still controversial in publications.In this work,a cold-flow LDPE autoclave with multi-feedings was scaled down(1/2)from an industrial reactor and built to systematically investigate the macro-and micro-mixing characteristics of fluid by experiments.Furthermore,the effects of macro-and micro-mixing on the polymerization were comprehensively analyzed.The results showed that according to the delay time t_(d) and macro-mixing times tM calculated from residence time distribution(RTD)curves,the macro-mixing states are significantly different at various axial positions(h/H),especially at lower agitation Reynolds number Re.But with the increase of Re,since the circulation flow in the reactor is strengthened,the t_(d) for each feed gradually decreases to 0,and the t_(M) at different axial positions tend to be identical.For micro-mixing,the qualities of micro-mixing at different axial positions are similar,and the average micro-mixing time t_(m) in the reactor decreases exponentially with the increase of Re.Moreover,a fitting model was established.Through the comparison of the characteristic times of macro-mixing(t_(d),t_(M)),micro-mixing(t_(m))and elementary reactions within the industrial range of Re,it can be concluded that the properties of LDPE products are dominated by the macro-mixing behavior,and the consumption of initiators is affected by both the macro-and micro-mixing behaviors.This conclusion is of great significance for the design,optimization and operation of LDPE reactors.
基金Funded by the Natural Science Foundation of Hebei Province(No.E2020209010)the Science and Technology Plan Project of Tangshan(No.19150225E)the Key R&D Projects of North China University of Science and Technology(No.ZD-ST-202301)。
文摘In view of the volume instability of steel slag aggregate leading to the quality problem of expansion damage in asphalt road construction,the 4.75-9.5 mm steel slag particles were treated by autoclaved carbonation technology,and the effects of the carbonation system(temperature and time)on the autoclaved pulverization rate,f-CaO content,and the relationship between them for the carbonated steel slag were investigated.In addition,the microstructure of the carbonated steel slag was analyzed by X-ray diffractometer(XRD),scanning electron microscope and energy dispersive spectrometer(SEM-EDS),metallographic microscope and X-ray fluorescence imaging spectrometer(XRF).The experimental results indicate that,under the initial CO_(2)pressure of 1.0 MPa,increasing the carbonation temperature leads to the increase in the crystal plane spacing of Ca(OH)_(2)that was generated by the hydration of minerals in steel slag,and promotes the transformation of carbonated CaCO_(3)from the orthorhombic system to the hexagonal system,resulting in the increase of the crystal planes spacing of them,meantime,accelerates the decomposition of RO phases and also the outward migration of Ca^(2+),Fe^(2+),and Mn^(2+)ions to cover and coat on the Si^(4+),Al^(3+)ions,and impels the formation of hydroxides such as Fe(OH)_(3)and the formation of carbonates such as Ca(Mg)CO_(3),FeCO_(3)and MnCO_(3).Carbonation at the temperature of 90℃for 3 h can reach the center of 4.75-9.5 mm steel slag particles.Meanwhile,the increase of temperature can promote the mineral reaction in steel slag,resulting in the fuzzy interface between mineral phases,increase of burrs,dispersion,crossover,reduction of grain size,and rearrangement of mineral particles.
文摘Objectives: There is a risk of spreading infectious material via non-sterile impressions. The aim of this study was to compare the effect of autoclave sterilisation on dimensional stability and tear strength of impression materials. Methods: Twenty-four specimens were produced using a standard ruled test block for each of three impression materials (Affinis, Aquasil and Speedex) to test dimensional stability. Thirty tear strips for each material were prepared for the tear test (ISO 34-1). Specimens were randomly allocated to 3 different groups (autoclaved, disinfected or untreated). A non-contact scanner was used to analyse dimensional change and a universal testing machine was used to determine tear strengths. Results: There were no significant differences in the test dimensions measured for any of the three impression materials following autoclave treatment compared to the disinfected or untreated control groups. The tear strengths were not adversely affected by autoclave sterilisation at 134°C. Conclusion: These addition and condensation-cured silicone impression materials can be steam autoclaved without adverse effects on dimensional accuracy or tear strength.
基金Supported by The State of So Paulo Research Foundation (FAPESP),that partially funded this study
文摘AIM:To evaluate the effect of autoclaved diet on the jejunum neurons of the myenteric plexus of rats during their growth.METHODS:The experimental groups were made up of rats going through weaning whose mothers received either an autoclaved or a non-autoclaved diet during gestation and lactation,and rats that were fed the same diet as their mothers during the post-weaning period.In order to measure the neurons'body profile and to quantify the number of neurons per area,preparations were stained by the nicotinamide adenine dinucleotide-diaphorase method.RESULTS:No significant changes were observed in rats'body weight or in the number of neurons regardless of the diet used(P>0.05) .There was a decrease in the jejunum-ileum length in rats treated with an autoclaved diet(P<0.05) .An increase in the neuronal cross-sectional area was seen in rats that had received the autoclaved diet,an effect that was significant for animals undergoing weaning.In addition,all observed factors showed significant differences when related to the age of the animals.CONCLUSION:The autoclaved diet did not alter the quantity of neurons,but increased their cell body area,suggesting changes similar to those observed in protein deficiency.
基金Supports from the National Natural Science Foundation of China(11672130,51508567,51478465,and 51308544)the State Key Laboratory of Mechanics and Control of Mechanical Structures(MCMS-0217G03)the State Key Laboratory for Disaster Reduction in Civil Engineering(SLDRCE16-01)。
文摘Autoclaved aerated concrete(AAC) panels have ultra-light weight,excellent thermal insulation and energy absorption,so it is an ideal building material for protective structures.To improve the blast resistance of the AAC panels,three schemes are applied to strengthen the AAC panels through spraying 4 mm thick polyurea coating from top,bottom and double-sides.In three-point bending tests,the polyurea-coated AAC panels have much higher ultimate loads than the un-coated panels,but slightly lower than those strengthened by the carbon fiber reinforced plastics(CEFRPs).Close-in explosion experiments reveal the dynamic strengthening effect of the polyurea coating.Critical scaled distances of the strengthened AAC panels are acquired,which are valuable for the engineering application of the AAC panels in the extreme loading conditions.Polyurea coatings efficiently enhance the blast resistance of the bottom and double-sided polyurea-coated AAC panels.It is interesting that the polyurea-coated AAC panels have much more excellent blast resistance than the CFRP reinforced AAC panels,although the latter have better static mechanical properties.
基金the National Natural Science Foundation of China (No.50678139)
文摘Suitable methods for enhancing the volume stability of steel slag utilized as fine aggregate were determined. The effects of steam treatment at 100 ℃ and autoclave treatment under 2.0 MPa on the soundness of steel slag sand were investigated by means of powder ratio, linear expansion, compressive and flexural strength. DTA, EDX, XRD and ethylene glycol methods were employed to analyze both the treated slags and susceptible expansion grains. Experimental results indicate that powder ratio, content of free lime and rate of linear expansion can express the improvement in volume stability of different treated methods. Steam treatment process cannot ultimately prevent specimens from cracking and decrease of strength, but mortar made from autoclave treated slag keeps integration subjected to hot water of 80℃ until 28 d and its strength do not show significant decrement. The hydration of over-burn free lime and periclase phase are the main cause for the disintegration or crack of untreated and steam treated steel slag＇s specimens. Autoclave treatment process is more effective than steam treatment process on enhancement of volume stability of steel slag.
基金financially supported by the National High Technology Research and Development Program of China (No. 2012AA063201)the National Natural Science Foundation of China (Nos. 51001002 and 51371002)+2 种基金the International S&T Cooperation Program of China (No.2015DFG52020)the Natural Science Foundation of Anhui Province (No.1408085MKL72)the 2011 Cooperative Innovation Center of Beijing University of Technology
文摘Nd-Fe-B permanent magnets doped with CuZn5 powders were prepared via conventional sintered method. The effects of CuZn5 contents on magnetic properties and corrosion resistance of the magnets were sys- tematically studied. It shows that the remanence, coercivity, and maximum energy product decrease gradually with the increase in CuZn5 doping content. The magnet＇s corrosion kinetics in autoclaves environment and its electrochemical properties in electrolytes were also examined. It is interesting to see that the weight loss of 3.5 wt% and 4.5 wt% CuZn5 powders doping magnets is only 1 and 0 mg.cm^-2 after autoclaves test at 121 ℃, 2 × 10^5 Pa for 500 h, respectively, which is much lower than that of the magnets without CuZn5 doping. Electrochemical results show that the CuZn5 powders doping magnets display more positive corrosion potential （Eoorr） and lower corrosion current density （Icorr） than those of the original magnets without CuZn5 doping in sulphuric acid electrolyte and distilled water. It is, therefore, concluded that doping CuZn5 powders is a promising way to enhance the corrosion resistance of sintered Nd-Fe-B magnets.
基金Funded by the National Natural Science Foundation of China(Nos.51272180,51072138)
文摘Synthesis of autoclaved aerated concrete （AAC） has been carried out with carbide slag addition, and the carbide slag could be used as a main material to produce the AAC with the compressive strength about 2 MPa and the density below 0.6 g.cm-3. In this study, quartz sand acted as frame structure phase in the matrix, and quartz addition also influenced the Si/Ca of starting material. Tobermorite and CSH gel were formed readily at 62%, which seemed to enhance the compressive strength of samples. Curing time seemed to affect the morphology of phase produced, and specimen with the plate-like tobermorite formed at 10 h appeared to have a better compressive strength development than the fiber-like one at 18 h. The higher curing temperature seemed to favor the tobermorite and CSH gel formation, which also exerted a significant effect on the strength development of the samples. On the micro-scale, the formed CSH gel was filled in the interface of the matrix, and the tobermorite appeared to grow in internal-surface of the pores and interstices. The tobermorite or/and CSH formation seemed to densify the matrix, and therefore enhanced the strength of the samples.
基金financially supported by the Scientific and Technological Research Council of Turkey (TUBITAK,No.106M177)
文摘The leaching behavior of a copper flotation concentrate was investigated using ammonium persulfate （APS） in an autoclave systee. The decomposition products of APS, active oxygen, and acidic medium were used to extract metals from the concentrate. Leaching experiments were performed to compare the availability of APS as an oxidizing agent for leaching of the concentrate under atmospheric conditions and in an autoclave system. Leaching temperature and APS concentration were found to be important parameters in both leaching systems. Atmospheric leaching studies showed that the metal extractions increased with the increase in APS concentration and temperature （up to 333 K）. A similar tendency was determined in the autoclave studies up to 423 K. It was also determined that the metal extractions decreased at temperatures above 423 K due to the passivation of the particle surface by molten elemental sulfur. The results showed that higher copper extractions could be achieved using an autoclave system.
基金supported by the National Natural Science Foundation of China (No. 40821140540)the National High Technology Research and Development Program (863) of China (No. 2007AA10Z218)
文摘Decomposition experiments conducted with and without microbial processes are commonly used to study the effects of environmental microorganisms on the degradation of organic pollutants.However,the effects of biological pretreatment （sterilization） on organic matter often have a negative impact on such experiments.Based on the principle of water total organic carbon （TOC） analysis,the effects of physical sterilization treatments on determination of TOC and other water quality parameters were investigated.The results revealed that two conventional physical sterilization treatments,autoclaving and 60 Co γ-radiation sterilization,led to the direct decomposition of some organic pollutants,resulting in remarkable errors in the analysis of TOC in water samples.Furthermore,the extent of the errors varied with the intensity and the duration of sterilization treatments.Accordingly,a novel sterilization method for water samples,0.45 μm micro-filtration coupled with ultraviolet radiation （MCUR）,was developed in the present study.The results indicated that the MCUR method was capable of exerting a high bactericidal effect on the water sample while significantly decreasing the negative impact on the analysis of TOC and other water quality parameters.Before and after sterilization treatments,the relative errors of TOC determination could be controlled to lower than 3% for water samples with different categories and concentrations of organic pollutants by using MCUR.
基金financially supported by the Joint Funds of the National Natural Science Foundation of China (Nos.U1402271, 51504058, and 51504059)
文摘The multiphase reaction process of pressure leaching is mainly carried out in the liquid phase. Therefore, gas holdup is essential for the gas–liquid–solid phase reaction and the extraction rate of valuable metals. In this paper, a transparent quartz autoclave, a six blades disc turbine-type agitator, and a high-speed camera were used to investigate the gas holdup of the pressure leaching process. Furthermore, experiments determining the effects of agitation rate, temperature, and oxygen partial pressure on gas holdup were carried out. The results showed that when the agitation rate increased from 350 to 600 r/min, the gas holdup increased from 0.10% to 0.64%. When the temperature increased from 363 to 423 K, the gas holdup increased from 0.14% to 0.20%. When the oxygen partial pressure increased from 0.1 to 0.8 MPa, the gas holdup increased from 0.13% to 0.19%. A similar criteria relationship was established by Homogeneous Principle and Buckingham's theorem. Comprehensively, empirical equation of gas holdup was deduced on the basis of experimental data and the similarity theory, where the criterion equation was determined as ε=4.54×10^(-11)n^(3.65)T^(2.08)P_g^(0.18). It can be seen from the formula that agitation rate made the most important impact on gas holdup in the pressure leaching process using the mixed-flow agitator.
基金The financial supports are from the Ministry of Education Malaysia under the Fundamental Research Grant Scheme(FRGS/1/2018/TK06/UKM/02/1).
文摘Autoclaved aerated concrete(AAC)has become more attractive due to its excellent and environmental-friendly properties in building construction.AAC is relatively lightweight,possesses lower thermal conductivity,higher heat resistance,lower shrinkage,and fasten construction than normal concrete.AAC is a combination of silica sand,cement,gypsum,lime,water,and an expansion agent.To improve its physical and mechanical properties and reduce its production cost,tremendous innovations where waste materials were utilized as partial replacement of AAC materials were done.This paper is intended to present the literature on the utilization of waste materials as a means of a partial replacement in AAC materials to enhance its physical and mechanical properties and thermal performance.The physical properties such as microstructure and mechanical properties such as density,compressive strength,water absorption are presented to classify the investigation that has been done in such innovations.Apart from that,the discussion on innovations to improve its thermal performance was also presented.Based on the review,an increase of AAC application causes much waste at construction sites and recycling concrete waste powder into wall concrete;particularly,an AAC was not frequently practiced in construction.
基金the National Natural Science Foundation of China(Nos.60307002,20472014)Doctoral Foundation of Dalian University of Technology(No.893327)Young Teacher Foundation of Dalian University of Technology,China.
文摘A novel solvothermal synthesis method for the direct growth of B-form crystals of copper phthalocyanine（CuPc） is presented in this article. With quinoline as solvent, crystals were grown after cooling the reaction mixture of 1,3-diiminoisoindoline and copper oxide, heated for 9 h at 270 ℃, to room temperature in an autoclave. These high quality crystals were suitable for characterization measurements. The single-crystal diffraction data show a monoclinic system unit cell： a=1.4668（3） nm, b=0.48109（10） nm, c=1.9515（7） nm, a=90°, B=121.04（2）°, r=90°, where the corresponding cell volume is 1.17991 nm^3. Needle-like single crystals of CuPc up to 10.5 mm in length were obtained. The influences of different temperatures, reaction time and solvent volume on the crystal yields were also discussed. Optimum reaction conditions were 10 mL of quinoline, at 270 ℃ for 8 h.
基金financed by the Fund from the Ministry of Science and Technology of People’s Republic of China under the grant number XDB18000000Major State Research Development Program of China under Grant Nos.2016YFC0601101 and 2016YFC0600109
文摘Due to the important scientific significance of the interaction between alkaline feldspar and high-temperature and high-pressure fluids. We have conducted a series of autoclave experiments of feldspar dissolution and secondary mineral precipitation in conditions of 250–500℃, 8-50 MPa, and pH = 3.0 and 5.5. Based on the interaction experiments between alkaline feldspar and fluid of high-temperatures and high-pressures, we get the main results as follows:(1) The law that people have grasped below the critical point about the influence of temperature, pressure, and pH value on the alkaline feldspar dissolution behavior is still held above the critical point.(2) Due to the experimental techniques of autoclave flip 180°—sharp quenching and based on electron microprobe analysis of mineral new formed, theoretical analysis has determined that the new altered minerals distributed on the island dissolution surface of feldspar are products of precipitation on a feldspar surface after saturation of the relative ion concentration in water fluid.
基金financially supported by the post doctoral fellowshipthe National Natural Science Foundation of China(No.51274170)the research grants from the Open Fund of Southwest Petroleum University(No.X151514KCL32)
文摘The influence of poly（methylmethacrylate-co-N-vinyl-2-pyrrolidone）, P（MMA-co-VP）, on corrosion of carbon steels（J55, N80, P110 SS and C110 steels） in 3.5 wt% NaCl solution saturated with CO2 was evaluated using static high pressure and high temperature（HPHT） autoclave. The surface was further evaluated by X-ray diffraction（XRD）, scanning electron microscopy（SEM） and contact angle measurements. Quantum chemical calculations have been used to evaluate the structural, electronic and reactivity parameters of the inhibitor on the steels surface. SEM, XRD and contact angle measurement studies reveal that the surface of metals are quite unaffected after use of inhibitor in 3.5% NaCl solution saturated with CO2.
基金supported by the National Key R&D Program of China(Grant No.2016YFC0600104)the Strategic Priority Research Program(B)of the Chinese Academy of Sciences(XDB 18010401)。
文摘We developed a set of in-situ Micro-Raman spectroscopy system for autoclave experimental apparatus because of the scientific significance of in-situ Micro-Raman spectroscopy system under the high-pressure hydrothermal condition.We used this system to measure the Raman spectrum of water-fluid and quartz crystal at the temperature ranging from 125 to 420℃.The signal-tonoise ratio of the Raman signal is good.
基金Funded by the National Nature Science Foundation of China(Nos.51468053,51772153,11662015,and 51769026)。
文摘We aimed to reuse the propylene oxide sludge(POS).Propylene oxide sludge shell-aggregate(POSS-A)and propylene oxide sludge gradient shell-aggregate(POSGS-A)whose main hydrated phase is tobermorite were successfully manufactured by the hydrothermal synthesis of POS and silica materials under the condition of autoclaved(180℃,1.0 MPa)curing.Influences of pre-wetting time of coarse aggregate and pressure application mode on the different concretes were investigated.The experimental results show that the concrete with POSS-A as coarse aggregate(POSS-A concrete),the concrete with POS gradient shell-aggregate as coarse aggregate(POSGS-A concrete),sintered aggregate concrete and common concrete,all have excellent impermeability performance whatever the pre-wetting time of coarse aggregate is 0.5 h or 24 h,and the pre-wetting time of coarse aggregate has a negligible influence on the concrete.The influence degree of pressure application mode on the impermeability performance of the sintered aggregate concrete is the greatest among three kinds of concrete,which has a negligible influence on impermeability performance of the other concretes.POSGS-A can be used as a green building light aggregate in hydraulic concrete.
