Recently, many optimal designs for axial flux permanent magnet (AFPM) motors were performed based on finite- element (FE) analysis. Most of the models are based on reduction of 3D problem to 2D problem which is not ac...Recently, many optimal designs for axial flux permanent magnet (AFPM) motors were performed based on finite- element (FE) analysis. Most of the models are based on reduction of 3D problem to 2D problem which is not accurate for design aspects. This paper describes an accurate electromagnetic analysis of a surface mounted, 28 pole AFPM with concentrated stator winding. The AFPM is modeled with three-dimensional finite-element method. This model in-cludes all geometrical and physical characteristics of the machine components. Using this accurate modeling makes it possible to obtain demanded signals for a very high precision analysis. Magnetic flux density, back-EMF, magnetic axial force and cogging torque of the motor are simulated using FLUX-3D V10.3.2. Meanwhile, the model is paramet-ric and can be used for design process and sensitivity analysis.展开更多
Three Dimensional Finite Element Method(3D-FEM)has been used to model the deviatoric stress field in a forsterite aggregate with a sandwich geometry:two forsterite cubes aligned in the same crystallographic orientatio...Three Dimensional Finite Element Method(3D-FEM)has been used to model the deviatoric stress field in a forsterite aggregate with a sandwich geometry:two forsterite cubes aligned in the same crystallographic orientation(the"breads")sandwich a third forsterite cube(the"filling"),which might have an identical or different crystallographic orientation.The results show that there is no von Mises stress in the forsterite sandwich if the sandwiching and sandwiched forsterite cubes are aligned in the same crystallographic orientation.If the crystallographic orientations are different,however,von Mises stress and heterogeneous stress distribution occur both along the boundary and in the forsterite cubes.For the investigated P-T conditions(up to 6.4GPa and 500°C),the resulted deviatoric stress is much lower than the yield strength of forsterite,so that higher P,higher T,or other means to create higher deviatoric stress is necessary,in order to constrain the yielding behavior of forsterite.展开更多
A new multi-mode resistivity imaging sonde, with toroidal coils as source, can conduct three resistivity measurements: azimuthal resistivity, lateral resistivity, and bit resistivity measurements. Thus, the logging ti...A new multi-mode resistivity imaging sonde, with toroidal coils as source, can conduct three resistivity measurements: azimuthal resistivity, lateral resistivity, and bit resistivity measurements. Thus, the logging time and cost are greatly saved. The toroidal coils are simplified as an extended voltage dipole and the response equations are derived for a homogenous formation. Based on 3D FEM, the depth of investigation(DOI), vertical resolution, circumferential azimuthal capacity, borehole diameter, mud resistivity, thickness of target formation, and the resistivity of the surrounding formation and mud invasion are simulated. The results suggest that the three measurement modes of the new sonde are different in vertical resolutions and DOIs. The circumferential detection ability of the azimuth button depends on the contrast between the anomaly and formation resistivity and the open angle of the anomaly. Whether the borehole is truncated at the bit or not has a great influence on the simulation results. The borehole and mud invasion affect the apparent resistivity in all modes, but the effects of resistivity of surrounding formation and thickness of the target formation are only corrected for lateral resistivity measurement.展开更多
文摘Recently, many optimal designs for axial flux permanent magnet (AFPM) motors were performed based on finite- element (FE) analysis. Most of the models are based on reduction of 3D problem to 2D problem which is not accurate for design aspects. This paper describes an accurate electromagnetic analysis of a surface mounted, 28 pole AFPM with concentrated stator winding. The AFPM is modeled with three-dimensional finite-element method. This model in-cludes all geometrical and physical characteristics of the machine components. Using this accurate modeling makes it possible to obtain demanded signals for a very high precision analysis. Magnetic flux density, back-EMF, magnetic axial force and cogging torque of the motor are simulated using FLUX-3D V10.3.2. Meanwhile, the model is paramet-ric and can be used for design process and sensitivity analysis.
基金supported by National Natural Science Foundation of China(Grant No.41090371)
文摘Three Dimensional Finite Element Method(3D-FEM)has been used to model the deviatoric stress field in a forsterite aggregate with a sandwich geometry:two forsterite cubes aligned in the same crystallographic orientation(the"breads")sandwich a third forsterite cube(the"filling"),which might have an identical or different crystallographic orientation.The results show that there is no von Mises stress in the forsterite sandwich if the sandwiching and sandwiched forsterite cubes are aligned in the same crystallographic orientation.If the crystallographic orientations are different,however,von Mises stress and heterogeneous stress distribution occur both along the boundary and in the forsterite cubes.For the investigated P-T conditions(up to 6.4GPa and 500°C),the resulted deviatoric stress is much lower than the yield strength of forsterite,so that higher P,higher T,or other means to create higher deviatoric stress is necessary,in order to constrain the yielding behavior of forsterite.
基金sponsored by Study on High-Precision Logging While Drilling Imaging Technology of Low-Permeability Reservoirs(No.2016ZX05021-002)
文摘A new multi-mode resistivity imaging sonde, with toroidal coils as source, can conduct three resistivity measurements: azimuthal resistivity, lateral resistivity, and bit resistivity measurements. Thus, the logging time and cost are greatly saved. The toroidal coils are simplified as an extended voltage dipole and the response equations are derived for a homogenous formation. Based on 3D FEM, the depth of investigation(DOI), vertical resolution, circumferential azimuthal capacity, borehole diameter, mud resistivity, thickness of target formation, and the resistivity of the surrounding formation and mud invasion are simulated. The results suggest that the three measurement modes of the new sonde are different in vertical resolutions and DOIs. The circumferential detection ability of the azimuth button depends on the contrast between the anomaly and formation resistivity and the open angle of the anomaly. Whether the borehole is truncated at the bit or not has a great influence on the simulation results. The borehole and mud invasion affect the apparent resistivity in all modes, but the effects of resistivity of surrounding formation and thickness of the target formation are only corrected for lateral resistivity measurement.
