The centroid coordinate serves as a critical control parameter in motion systems,including aircraft,missiles,rockets,and drones,directly influencing their motion dynamics and control performance.Traditional methods fo...The centroid coordinate serves as a critical control parameter in motion systems,including aircraft,missiles,rockets,and drones,directly influencing their motion dynamics and control performance.Traditional methods for centroid measurement often necessitate custom equipment and specialized positioning devices,leading to high costs and limited accuracy.Here,we present a centroid measurement method that integrates 3D scanning technology,enabling accurate measurement of centroid across various types of objects without the need for specialized positioning fixtures.A theoretical framework for centroid measurement was established,which combined the principle of the multi-point weighing method with 3D scanning technology.The measurement accuracy was evaluated using a designed standard component.Experimental results demonstrate that the discrepancies between the theoretical and the measured centroid of a standard component with various materials and complex shapes in the X,Y,and Z directions are 0.003 mm,0.009 mm,and 0.105 mm,respectively,yielding a spatial deviation of 0.106 mm.Qualitative verification was conducted through experimental validation of three distinct types.They confirmed the reliability of the proposed method,which allowed for accurate centroid measurements of various products without requiring positioning fixtures.This advancement significantly broadened the applicability and scope of centroid measurement devices,offering new theoretical insights and methodologies for the measurement of complex parts and systems.展开更多
In this paper,a linear optimization method(LOM)for the design of terahertz circuits is presented,aimed at enhancing the simulation efficacy and reducing the time of the circuit design workflow.This method enables the ...In this paper,a linear optimization method(LOM)for the design of terahertz circuits is presented,aimed at enhancing the simulation efficacy and reducing the time of the circuit design workflow.This method enables the rapid determination of optimal embedding impedance for diodes across a specific bandwidth to achieve maximum efficiency through harmonic balance simulations.By optimizing the linear matching circuit with the optimal embedding impedance,the method effectively segregates the simulation of the linear segments from the nonlinear segments in the frequency multiplier circuit,substantially improving the speed of simulations.The design of on-chip linear matching circuits adopts a modular circuit design strategy,incorporating fixed load resistors to simplify the matching challenge.Utilizing this approach,a 340 GHz frequency doubler was developed and measured.The results demonstrate that,across a bandwidth of 330 GHz to 342 GHz,the efficiency of the doubler remains above 10%,with an input power ranging from 98 mW to 141mW and an output power exceeding 13 mW.Notably,at an input power of 141 mW,a peak output power of 21.8 mW was achieved at 334 GHz,corresponding to an efficiency of 15.8%.展开更多
In order to improve the quality of 3D printed raspberry preserves after post-processing,microwave ovens combining infrared and microwave methods were utilized.The effects of infrared heating temperature,infrared heati...In order to improve the quality of 3D printed raspberry preserves after post-processing,microwave ovens combining infrared and microwave methods were utilized.The effects of infrared heating temperature,infrared heating time,microwave power,microwave heating time on the center temperature,moisture content,the chroma(C*),the total color difference(ΔE*),shape fidelity,hardness,and the total anthocyanin content of 3D printed raspberry preserves were analyzed by response surface method(RSM).The results showed that under combining with the two methods,infrared heating improved the fidelity and quality degradation of printed products,while microwave heating enhanced the efficiency of infrared heating.Infrared-microwave combination cooking could maintain relatively stable color appearance and shape of 3D printed raspberry preserves.The AHP–CRITIC hybrid weighting method combined with the response surface test to determine the comprehensive weights of the evaluation indicators optimized the process parameters,and the optimal process parameters were obtained:infrared heating temperature of 190℃,infrared heating time of 10 min and 30 s,microwave power of 300 W,and microwave heating time of 2 min and 6 s.The 3D printed raspberry cooking methods obtained under the optimal conditions seldom had color variation,porous structure,uniform texture,and high shape fidelity,which retained the characteristics of personalized manufacturing by 3D printing.This study could provide a reference for the postprocessing and quality control of 3D cooking methods.展开更多
The modeling of crack growth in three-dimensional(3D)space poses significant challenges in rock mechanics due to the complex numerical computation involved in simulating crack propagation and interaction in rock mater...The modeling of crack growth in three-dimensional(3D)space poses significant challenges in rock mechanics due to the complex numerical computation involved in simulating crack propagation and interaction in rock materials.In this study,we present a novel approach that introduces a 3D numerical manifold method(3D-NMM)with a geometric kernel to enhance computational efficiency.Specifically,the maximum tensile stress criterion is adopted as a crack growth criterion to achieve strong discontinuous crack growth,and a local crack tracking algorithm and an angle correction technique are incorporated to address minor limitations of the algorithm in a 3D model.The implementation of the program is carried out in Python,using object-oriented programming in two independent modules:a calculation module and a crack module.Furthermore,we propose feasible improvements to enhance the performance of the algorithm.Finally,we demonstrate the feasibility and effectiveness of the enhanced algorithm in the 3D-NMM using four numerical examples.This study establishes the potential of the 3DNMM,combined with the local tracking algorithm,for accurately modeling 3D crack propagation in brittle rock materials.展开更多
This paper adopted the hydrothermal method to prepare tungsten oxide(WO_(3))nanorod films and studied the effects of precursor solution concentration(0.02,0.03,0.06 mol/L peroxytungstic acid)and annealing temperature(...This paper adopted the hydrothermal method to prepare tungsten oxide(WO_(3))nanorod films and studied the effects of precursor solution concentration(0.02,0.03,0.06 mol/L peroxytungstic acid)and annealing temperature(200,300,400℃)on their electrochromic properties.The microstructure characterization of WO_(3) films were performed using scanning electron microscope(SEM),X-ray diffraction(XRD),and transmission electron microscope(TEM),and their electrochromic properties were tested by combining an electrochemical workstation with an ultraviolet-visible spectrophotometer.The results showed that the precursor solution concentration directly affected the thickness(290,560,990 nm)and microstructure of WO_(3) films,significantly impacting their electrochromic properties.However,the annealing temperature had a negligible effect.As the precursor solution concentration increased,the optical modulation of WO_(3) films gradually decreased,reaching 51.1%,43.8%,and 35.1%,respectively.The switching time first increased and then stabilized,with coloring times of 7.3,7.7,and 7.7 s,respectively,and bleaching times of 3.8,6.5,and 6.5 s,respectively.The coloration efficiency gradually increased but the increase was relatively small,reaching 41.8,44.4,and 44.8 cm^(2)/C,respectively.Moreover,the cycling stability of WO_(3) films was poor,with the ratios of the final value of optical modulation to the initial value 0.33,0.26,and 0.34,respectively.Additionally,there were bigger differences in the bleached state transmittance,while the colored state transmittance showed smaller variations.However,the former has better cycling stability than the latter.In summary,to obtain better electrochromic properties,the thickness of WO_(3) films should not exceed 290 nm.展开更多
This article presents a micro-structure tensor enhanced elasto-plastic finite element(FE)method to address strength anisotropy in three-dimensional(3D)soil slope stability analysis.The gravity increase method(GIM)is e...This article presents a micro-structure tensor enhanced elasto-plastic finite element(FE)method to address strength anisotropy in three-dimensional(3D)soil slope stability analysis.The gravity increase method(GIM)is employed to analyze the stability of 3D anisotropic soil slopes.The accuracy of the proposed method is first verified against the data in the literature.We then simulate the 3D soil slope with a straight slope surface and the convex and concave slope surfaces with a 90turning corner to study the 3D effect on slope stability and the failure mechanism under anisotropy conditions.Based on our numerical results,the end effect significantly impacts the failure mechanism and safety factor.Anisotropy degree notably affects the safety factor,with higher degrees leading to deeper landslides.For concave slopes,they can be approximated by straight slopes with suitable boundary conditions to assess their stability.Furthermore,a case study of the Saint-Alban test embankment A in Quebec,Canada,is provided to demonstrate the applicability of the proposed FE model.展开更多
Norfloxacin is widely used owing to its strong bactericidal effect on Gram-negative bacteria.However,the residual norfloxacin in the environment can be biomagnified via food chain andmay damage the human liver and del...Norfloxacin is widely used owing to its strong bactericidal effect on Gram-negative bacteria.However,the residual norfloxacin in the environment can be biomagnified via food chain andmay damage the human liver and delay the bone development ofminors.Present work described a reliable and sensitive smartphone colorimetric sensing system based on cobaltdoped Fe_(3)O_(4) magnetic nanoparticles(Co-Fe_(3)O_(4) MNPs)for the visual detection of norfloxacin.Compared with Fe_(3)O_(4),Co-Fe_(3)O_(4) MNPs earned more remarkably peroxidase-like activity and TMB(colorless)was rapidly oxidized to oxTMB(blue)with the presence of H_(2)O_(2).Interestingly,the addition of low concentration of norfloxacin can accelerate the color reaction process of TMB,and blue deepening of the solution can be observed with the naked eye.However,after adding high concentration of norfloxacin,the activity of nanozymewas inhibited,resulting in the gradual fading of the solution.Based on this principle,a colorimetric sensor integrated with smartphone RGB mode was established.The visual sensor exhibited good linearity for norfloxacin monitoring in the range of 0.13-2.51μmol/L and 17.5-100μmol/L.The limit of visual detectionwas 0.08μmol/L.In the actualwater sample analysis,the spiked recoveries of norfloxacin were over the range of 95.7%-104.7%.These results demonstrated that the visual sensor was a convenient and fast method for the efficient and accurate detection of norfloxacin in water,which may have broad application prospect.展开更多
3D traveltime calculation is widely used in seismic exploration technologies such as seismic migration and tomography. The fast marching method （FMM） is useful for calculating 3D traveltime and has proven to be effi...3D traveltime calculation is widely used in seismic exploration technologies such as seismic migration and tomography. The fast marching method （FMM） is useful for calculating 3D traveltime and has proven to be efficient and stable. However, it has low calculation accuracy near the source, which thus gives it low overall accuracy. This paper proposes a joint traveltime calculation method to solve this problem. The method firstly employs the wavefront construction method （WFC）, which has a higher calculation accuracy than FMM in calculating traveltime in the small area near the source, and secondly adopts FMM to calculate traveltime for the remaining grid nodes. Due to the increase in calculation precision of grid nodes near the source, this new algorithm is shown to have good calculation precision while maintaining the high calculation efficiency of FMM, which is employed in most of the computational area. Results are verified using various numerical models.展开更多
A new algorithm based on the projection method with the implicit finite difference technique was established to calculate the velocity fields and pressure.The calculation region can be divided into different regions a...A new algorithm based on the projection method with the implicit finite difference technique was established to calculate the velocity fields and pressure.The calculation region can be divided into different regions according to Reynolds number.In the far-wall region,the thermal melt flow was calculated as Newtonian flow.In the near-wall region,the thermal melt flow was calculated as non-Newtonian flow.It was proved that the new algorithm based on the projection method with the implicit technique was correct through nonparametric statistics method and experiment.The simulation results show that the new algorithm based on the projection method with the implicit technique calculates more quickly than the solution algorithm-volume of fluid method using the explicit difference method.展开更多
Tikhonov regularization（TR） method has played a very important role in the gravity data and magnetic data process. In this paper, the Tikhonov regularization method with respect to the inversion of gravity data is d...Tikhonov regularization（TR） method has played a very important role in the gravity data and magnetic data process. In this paper, the Tikhonov regularization method with respect to the inversion of gravity data is discussed. and the extrapolated TR method（EXTR） is introduced to improve the fitting error. Furthermore, the effect of the parameters in the EXTR method on the fitting error, number of iterations, and inversion results are discussed in details. The computation results using a synthetic model with the same and different densities indicated that. compared with the TR method, the EXTR method not only achieves the a priori fitting error level set by the interpreter but also increases the fitting precision, although it increases the computation time and number of iterations. And the EXTR inversion results are more compact than the TR inversion results, which are more divergent. The range of the inversion data is closer to the default range of the model parameters, and the model features and default model density distribution agree well.展开更多
Nanocrystal of upconversion （UC） phosphor Ho^3＋, Tm^3＋ , and Yb^3＋ co-doped NaYF4 was prepared by the hydrothermal method in the presence of the complexing agent EDTA. Under 980 nm diode laser excitation, the imp...Nanocrystal of upconversion （UC） phosphor Ho^3＋, Tm^3＋ , and Yb^3＋ co-doped NaYF4 was prepared by the hydrothermal method in the presence of the complexing agent EDTA. Under 980 nm diode laser excitation, the impact of different concentrations of Ho^3＋ ion on the UC luminescence intensity was discussed. The law of luminescence intensity versus pump power shows that the 474 nm blue emission, 538 nm green emission, and 642 nm red emission are all due to the two-photon process, while the 450 nm blue emission is a three-photon process. The UC mechanism and processes were also analyzed. The sample was characterized by transmission electron microscopy （TEM） and X-ray diffraction （XRD）. The result shows that Ho^3＋ ,Tm^3＋ , and Yb^3＋ co-doped NaYF4 prepared by the hydrothermal method exhibits a hexagonal nanocrystal.展开更多
3-D geological modeling plays an increasingly important role in Petroleum Geology, Mining Geology and Engineering Geology. The complexity of geological conditions requires different modeling methods in different situa...3-D geological modeling plays an increasingly important role in Petroleum Geology, Mining Geology and Engineering Geology. The complexity of geological conditions requires different modeling methods in different situations. This paper summarizes the general concept of geological modeling; compares the characteristics of borehole-based modeling, cross-section based modeling and multi- source interactive modeling; analyses key techniques in 3-D geological modeling; and highlights the main difficulties and directions of future studies.展开更多
Y2O3： Er^3＋, Yb^3＋ nanoparticles were synthesized by a homogeneous precipitation method without and with different concentrations of EDTA 2Na. Upconversion luminescence spectra of the samples were studied under 980...Y2O3： Er^3＋, Yb^3＋ nanoparticles were synthesized by a homogeneous precipitation method without and with different concentrations of EDTA 2Na. Upconversion luminescence spectra of the samples were studied under 980 nm laser excitation. The results of XRD showed that the obtained Y2O3：Er^3＋,Yb^3＋ nanoparticles were of a cubic structure. The average crystallite sizes calculated were in the range of 28-40 nm. Green and red upconversion emission were observed, and attributed to ^2H11/2,^4S3/2→^4I15/2 and ^4F9/2→^4I15/2 transitions of the ion, respectively. The ratio of the intensity of green emission to that of red emission drastically changed with a change in the EDTA 2Na concentration. In the sample synthesized without EDTA, the relative intensity of the green emission was weaker than that of the red emission. The relative intensities of green emission increased with the increased amount of EDTA 2Na used. The possible upconversion luminescence mechanisms were discussed.展开更多
A series of TiO 2-MoO 3 nano-composite photocatalysts were prepared by supercritical fluid dry method(SCFD) and an impregnation technique with TiCl 4 and (NH 4) 6Mo 7O 24 ·4H 2O as the starting materia...A series of TiO 2-MoO 3 nano-composite photocatalysts were prepared by supercritical fluid dry method(SCFD) and an impregnation technique with TiCl 4 and (NH 4) 6Mo 7O 24 ·4H 2O as the starting materials. The catalysts were characterized by the means of XRD, TEM and UV-Vis. Methyl orange was used as model compound for the evaluation of their catalytic activities. The results indicated that the photo-catalyst prepared by SCFD had the advantages of small size(12.84 nm), narrow distribution and good dispersivity. The presence of small amount of Mo in composite catalyst gives rise to the red shift of its absorbance wavelength, decrease of its energy gap and increase of the utility of visible light. Furthermore, higher surface acidity of the photo-catalyst was obtained as the result of the addition of MoO 3. Compared with pure TiO 2, the catalytic activity of the TiO 2-MoO 3 nano-composite photo-catalyst was improved significantly. As the doping concentration of the composite catalysts was controlled at 0.6%(molar percentage), 100% degradation of methyl orange was achieved with in 1.2 h irradiation time.展开更多
The europium-doped LaF3 nanoparticles were prepared by refluxing method in glycerol/water mixture and characterized with X-ray diffraction（XRD）, field emission scanning electron microscopy（FE-SEM）, UV-vis diffuse ...The europium-doped LaF3 nanoparticles were prepared by refluxing method in glycerol/water mixture and characterized with X-ray diffraction（XRD）, field emission scanning electron microscopy（FE-SEM）, UV-vis diffuse reflectance spectrum, and photoluminescence spectra.The results of XRD indicated that the obtained LaF3：Eu^3＋ nanoparticles were well crystallized with a hexagonal structure.The FE-SEM image illustrated that the LaF3：Eu^3＋ nanoparticles were spherical with an average size around 30 nm.Under irradiation of UV light, the emission spectrum of LaF3：Eu^3＋ nanoparticles exhibited the characteristic line emissions arising from the 5D0→7FJ（J=1, 2, 3, 4） transitions of the Eu3＋ ions, with the dominating emission centered at 590 nm.In addition, the emissions from the 5D1 level could be clearly observed due to the low phonon energies（-350 cm^-1） of LaF3 matrix.The optimum doping concentration for LaF3：Eu3＋ nanoparticles was determined to be 20mol.%.展开更多
Mixed strontium-yttrium borate phosphor Sr3Y2（BO3）4 doped with Eu^3＋ ions was obtained by the sol-gel Pechini method. Crystal structure of the synthesized compound was analyzed by X-ray powder diffraction. Optimal ...Mixed strontium-yttrium borate phosphor Sr3Y2（BO3）4 doped with Eu^3＋ ions was obtained by the sol-gel Pechini method. Crystal structure of the synthesized compound was analyzed by X-ray powder diffraction. Optimal conditions for the synthesis were found. Photophysical properties of the phosphor samples were investigated by collecting excitation and luminescence spectra as well as measuring lumi- nescence lifetime. Judd-Ofelt analysis showed that Eu^3＋ ions occupied Y^3＋ sites in the crystalline network. The studied compound showed a red emission with the quantum yield of 54%-55% and can be potentially used as phosphor for plasma display panels and luminescent tubes.展开更多
在强光照射下,CdS量子点易发生光腐蚀现象,通过金属掺杂和复合的方式可以提高CdS的光催化性能和光稳定性。采用水热法合成了Zn掺杂CdS/g-C_(3)N_(4)复合纳米材料(Zn-CdS/g-C_(3)N_(4))。利用扫描电子显微镜(SEM)、透射电子显微镜(TEM)、...在强光照射下,CdS量子点易发生光腐蚀现象,通过金属掺杂和复合的方式可以提高CdS的光催化性能和光稳定性。采用水热法合成了Zn掺杂CdS/g-C_(3)N_(4)复合纳米材料(Zn-CdS/g-C_(3)N_(4))。利用扫描电子显微镜(SEM)、透射电子显微镜(TEM)、X射线衍射(XRD)、X射线光电子能谱(XPS)和傅里叶变换红外光谱(FT-IR)等手段对Zn-CdS/g-C_(3)N_(4)复合材料的形貌、结构和组成等进行了表征。结果表明,Zn-CdS纳米颗粒附着在g-C_(3)N_(4)表面上,从而形成Zn-CdS/g-C_(3)N_(4)复合材料,且复合后材料带隙减小,光生电子-空穴复合率降低。在500 W Xe灯照射下,研究了Zn-CdS/g-C_(3)N_(4)对罗丹明B(RhB)的光催化降解性能。在最优条件下,光照40 min后,所制备的Zn-CdS/g-C_(3)N_(4)对RhB的光催化降解效率达99%。此外,所合成的Zn-CdS/g-C_(3)N_(4)复合材料光稳定性较高、可再生性好。这归因于Zn和Cd的协同作用以及与g-C_(3)N_(4)的复合,促进了光生载流子的分离和转移。展开更多
Bi 2O 3 nanoparticles were prepared by means of ammonia precipitation, polyol mediated methods and microemulsion chemical method. The structure and properties of the as-prepared nanoparticles, having been submitted to...Bi 2O 3 nanoparticles were prepared by means of ammonia precipitation, polyol mediated methods and microemulsion chemical method. The structure and properties of the as-prepared nanoparticles, having been submitted to a heat-treatment test at 750 ℃, were characterized by means of XRD, BET, XPS and UV-Vis absorption techniques. The photocatalytic oxidation reactions of benzene, toluene and xylene were used as the model reaction to measure the photocatalytic activity of Bi 2O 3 nanoparticles, respectively. The results show that the crystallite size of Bi 2O 3 prepared with different methods and calcined at 750 ℃ were 50.6, 38.5 and 31.5 nm, respectively. The photocatalytic activity of Bi 2O 3 nanoparticles prepared with the microemulsion chemical method was higher than that of the particles prepared with the polyol mediated method; and that of the particles prepared with the micromulsion chemical method was the highest among the three. The degradation rates of the three pollutants xylene, toluene and benzene decreased in sequence.展开更多
基金supported by National Natural Science Foundation of China(No.52176122).
文摘The centroid coordinate serves as a critical control parameter in motion systems,including aircraft,missiles,rockets,and drones,directly influencing their motion dynamics and control performance.Traditional methods for centroid measurement often necessitate custom equipment and specialized positioning devices,leading to high costs and limited accuracy.Here,we present a centroid measurement method that integrates 3D scanning technology,enabling accurate measurement of centroid across various types of objects without the need for specialized positioning fixtures.A theoretical framework for centroid measurement was established,which combined the principle of the multi-point weighing method with 3D scanning technology.The measurement accuracy was evaluated using a designed standard component.Experimental results demonstrate that the discrepancies between the theoretical and the measured centroid of a standard component with various materials and complex shapes in the X,Y,and Z directions are 0.003 mm,0.009 mm,and 0.105 mm,respectively,yielding a spatial deviation of 0.106 mm.Qualitative verification was conducted through experimental validation of three distinct types.They confirmed the reliability of the proposed method,which allowed for accurate centroid measurements of various products without requiring positioning fixtures.This advancement significantly broadened the applicability and scope of centroid measurement devices,offering new theoretical insights and methodologies for the measurement of complex parts and systems.
基金Supported by the Beijing Municipal Science&Technology Commission(Z211100004421012),the Key Reaserch and Development Pro⁃gram of China(2022YFF0605902)。
文摘In this paper,a linear optimization method(LOM)for the design of terahertz circuits is presented,aimed at enhancing the simulation efficacy and reducing the time of the circuit design workflow.This method enables the rapid determination of optimal embedding impedance for diodes across a specific bandwidth to achieve maximum efficiency through harmonic balance simulations.By optimizing the linear matching circuit with the optimal embedding impedance,the method effectively segregates the simulation of the linear segments from the nonlinear segments in the frequency multiplier circuit,substantially improving the speed of simulations.The design of on-chip linear matching circuits adopts a modular circuit design strategy,incorporating fixed load resistors to simplify the matching challenge.Utilizing this approach,a 340 GHz frequency doubler was developed and measured.The results demonstrate that,across a bandwidth of 330 GHz to 342 GHz,the efficiency of the doubler remains above 10%,with an input power ranging from 98 mW to 141mW and an output power exceeding 13 mW.Notably,at an input power of 141 mW,a peak output power of 21.8 mW was achieved at 334 GHz,corresponding to an efficiency of 15.8%.
基金Supported by the National Natural Science Foundation of China(32072352)。
文摘In order to improve the quality of 3D printed raspberry preserves after post-processing,microwave ovens combining infrared and microwave methods were utilized.The effects of infrared heating temperature,infrared heating time,microwave power,microwave heating time on the center temperature,moisture content,the chroma(C*),the total color difference(ΔE*),shape fidelity,hardness,and the total anthocyanin content of 3D printed raspberry preserves were analyzed by response surface method(RSM).The results showed that under combining with the two methods,infrared heating improved the fidelity and quality degradation of printed products,while microwave heating enhanced the efficiency of infrared heating.Infrared-microwave combination cooking could maintain relatively stable color appearance and shape of 3D printed raspberry preserves.The AHP–CRITIC hybrid weighting method combined with the response surface test to determine the comprehensive weights of the evaluation indicators optimized the process parameters,and the optimal process parameters were obtained:infrared heating temperature of 190℃,infrared heating time of 10 min and 30 s,microwave power of 300 W,and microwave heating time of 2 min and 6 s.The 3D printed raspberry cooking methods obtained under the optimal conditions seldom had color variation,porous structure,uniform texture,and high shape fidelity,which retained the characteristics of personalized manufacturing by 3D printing.This study could provide a reference for the postprocessing and quality control of 3D cooking methods.
基金supported by the National Natural Science Foundation of China(Grant Nos.42172312 and 52211540395)support from the Institut Universitaire de France(IUF).
文摘The modeling of crack growth in three-dimensional(3D)space poses significant challenges in rock mechanics due to the complex numerical computation involved in simulating crack propagation and interaction in rock materials.In this study,we present a novel approach that introduces a 3D numerical manifold method(3D-NMM)with a geometric kernel to enhance computational efficiency.Specifically,the maximum tensile stress criterion is adopted as a crack growth criterion to achieve strong discontinuous crack growth,and a local crack tracking algorithm and an angle correction technique are incorporated to address minor limitations of the algorithm in a 3D model.The implementation of the program is carried out in Python,using object-oriented programming in two independent modules:a calculation module and a crack module.Furthermore,we propose feasible improvements to enhance the performance of the algorithm.Finally,we demonstrate the feasibility and effectiveness of the enhanced algorithm in the 3D-NMM using four numerical examples.This study establishes the potential of the 3DNMM,combined with the local tracking algorithm,for accurately modeling 3D crack propagation in brittle rock materials.
基金the National Natural Science Foundation of China(No.52272009)the Henan Provincial Science and Technology Research Project(No.242102230151)+1 种基金the Henan Provincial University Science and Technology Innovation Team(No.25IRTSTHN009)the Key Scientific Research Projects of Colleges and Universities in Henan Province(Nos.24B560021,25B560020,25B560023)。
文摘This paper adopted the hydrothermal method to prepare tungsten oxide(WO_(3))nanorod films and studied the effects of precursor solution concentration(0.02,0.03,0.06 mol/L peroxytungstic acid)and annealing temperature(200,300,400℃)on their electrochromic properties.The microstructure characterization of WO_(3) films were performed using scanning electron microscope(SEM),X-ray diffraction(XRD),and transmission electron microscope(TEM),and their electrochromic properties were tested by combining an electrochemical workstation with an ultraviolet-visible spectrophotometer.The results showed that the precursor solution concentration directly affected the thickness(290,560,990 nm)and microstructure of WO_(3) films,significantly impacting their electrochromic properties.However,the annealing temperature had a negligible effect.As the precursor solution concentration increased,the optical modulation of WO_(3) films gradually decreased,reaching 51.1%,43.8%,and 35.1%,respectively.The switching time first increased and then stabilized,with coloring times of 7.3,7.7,and 7.7 s,respectively,and bleaching times of 3.8,6.5,and 6.5 s,respectively.The coloration efficiency gradually increased but the increase was relatively small,reaching 41.8,44.4,and 44.8 cm^(2)/C,respectively.Moreover,the cycling stability of WO_(3) films was poor,with the ratios of the final value of optical modulation to the initial value 0.33,0.26,and 0.34,respectively.Additionally,there were bigger differences in the bleached state transmittance,while the colored state transmittance showed smaller variations.However,the former has better cycling stability than the latter.In summary,to obtain better electrochromic properties,the thickness of WO_(3) films should not exceed 290 nm.
基金supported by the National Natural Science Foundation of China(Grant Nos.51890912,51979025 and 52011530189).
文摘This article presents a micro-structure tensor enhanced elasto-plastic finite element(FE)method to address strength anisotropy in three-dimensional(3D)soil slope stability analysis.The gravity increase method(GIM)is employed to analyze the stability of 3D anisotropic soil slopes.The accuracy of the proposed method is first verified against the data in the literature.We then simulate the 3D soil slope with a straight slope surface and the convex and concave slope surfaces with a 90turning corner to study the 3D effect on slope stability and the failure mechanism under anisotropy conditions.Based on our numerical results,the end effect significantly impacts the failure mechanism and safety factor.Anisotropy degree notably affects the safety factor,with higher degrees leading to deeper landslides.For concave slopes,they can be approximated by straight slopes with suitable boundary conditions to assess their stability.Furthermore,a case study of the Saint-Alban test embankment A in Quebec,Canada,is provided to demonstrate the applicability of the proposed FE model.
基金supported by the National Natural Science Foundation of China (No.21976211).
文摘Norfloxacin is widely used owing to its strong bactericidal effect on Gram-negative bacteria.However,the residual norfloxacin in the environment can be biomagnified via food chain andmay damage the human liver and delay the bone development ofminors.Present work described a reliable and sensitive smartphone colorimetric sensing system based on cobaltdoped Fe_(3)O_(4) magnetic nanoparticles(Co-Fe_(3)O_(4) MNPs)for the visual detection of norfloxacin.Compared with Fe_(3)O_(4),Co-Fe_(3)O_(4) MNPs earned more remarkably peroxidase-like activity and TMB(colorless)was rapidly oxidized to oxTMB(blue)with the presence of H_(2)O_(2).Interestingly,the addition of low concentration of norfloxacin can accelerate the color reaction process of TMB,and blue deepening of the solution can be observed with the naked eye.However,after adding high concentration of norfloxacin,the activity of nanozymewas inhibited,resulting in the gradual fading of the solution.Based on this principle,a colorimetric sensor integrated with smartphone RGB mode was established.The visual sensor exhibited good linearity for norfloxacin monitoring in the range of 0.13-2.51μmol/L and 17.5-100μmol/L.The limit of visual detectionwas 0.08μmol/L.In the actualwater sample analysis,the spiked recoveries of norfloxacin were over the range of 95.7%-104.7%.These results demonstrated that the visual sensor was a convenient and fast method for the efficient and accurate detection of norfloxacin in water,which may have broad application prospect.
基金supported by NSFC(Nos.41274120,41404085,and 41504084)
文摘3D traveltime calculation is widely used in seismic exploration technologies such as seismic migration and tomography. The fast marching method （FMM） is useful for calculating 3D traveltime and has proven to be efficient and stable. However, it has low calculation accuracy near the source, which thus gives it low overall accuracy. This paper proposes a joint traveltime calculation method to solve this problem. The method firstly employs the wavefront construction method （WFC）, which has a higher calculation accuracy than FMM in calculating traveltime in the small area near the source, and secondly adopts FMM to calculate traveltime for the remaining grid nodes. Due to the increase in calculation precision of grid nodes near the source, this new algorithm is shown to have good calculation precision while maintaining the high calculation efficiency of FMM, which is employed in most of the computational area. Results are verified using various numerical models.
基金Project (50975263) supported by the National Natural Science Foundation of ChinaProject (2010081015) supported by International Cooperation Project of Shanxi Province, China+1 种基金 Project (2010-78) supported by the Scholarship Council in Shanxi province, ChinaProject (2010420120005) supported by Doctoral Fund of Ministry of Education of China
文摘A new algorithm based on the projection method with the implicit finite difference technique was established to calculate the velocity fields and pressure.The calculation region can be divided into different regions according to Reynolds number.In the far-wall region,the thermal melt flow was calculated as Newtonian flow.In the near-wall region,the thermal melt flow was calculated as non-Newtonian flow.It was proved that the new algorithm based on the projection method with the implicit technique was correct through nonparametric statistics method and experiment.The simulation results show that the new algorithm based on the projection method with the implicit technique calculates more quickly than the solution algorithm-volume of fluid method using the explicit difference method.
基金supported by the National Scientific and Technological Plan(Nos.2009BAB43B00 and 2009BAB43B01)
文摘Tikhonov regularization（TR） method has played a very important role in the gravity data and magnetic data process. In this paper, the Tikhonov regularization method with respect to the inversion of gravity data is discussed. and the extrapolated TR method（EXTR） is introduced to improve the fitting error. Furthermore, the effect of the parameters in the EXTR method on the fitting error, number of iterations, and inversion results are discussed in details. The computation results using a synthetic model with the same and different densities indicated that. compared with the TR method, the EXTR method not only achieves the a priori fitting error level set by the interpreter but also increases the fitting precision, although it increases the computation time and number of iterations. And the EXTR inversion results are more compact than the TR inversion results, which are more divergent. The range of the inversion data is closer to the default range of the model parameters, and the model features and default model density distribution agree well.
基金Project supported bythe Key Laboratory of Rare Earth Chemistry and Physics ,ChangchunInstitute of Applied Chemistry ,Chinese Academy of Sciences (R020202K)
文摘Nanocrystal of upconversion （UC） phosphor Ho^3＋, Tm^3＋ , and Yb^3＋ co-doped NaYF4 was prepared by the hydrothermal method in the presence of the complexing agent EDTA. Under 980 nm diode laser excitation, the impact of different concentrations of Ho^3＋ ion on the UC luminescence intensity was discussed. The law of luminescence intensity versus pump power shows that the 474 nm blue emission, 538 nm green emission, and 642 nm red emission are all due to the two-photon process, while the 450 nm blue emission is a three-photon process. The UC mechanism and processes were also analyzed. The sample was characterized by transmission electron microscopy （TEM） and X-ray diffraction （XRD）. The result shows that Ho^3＋ ,Tm^3＋ , and Yb^3＋ co-doped NaYF4 prepared by the hydrothermal method exhibits a hexagonal nanocrystal.
文摘3-D geological modeling plays an increasingly important role in Petroleum Geology, Mining Geology and Engineering Geology. The complexity of geological conditions requires different modeling methods in different situations. This paper summarizes the general concept of geological modeling; compares the characteristics of borehole-based modeling, cross-section based modeling and multi- source interactive modeling; analyses key techniques in 3-D geological modeling; and highlights the main difficulties and directions of future studies.
基金the Foundation for the University by Educational Department of Liaoning (05L337)Key Laboratory of Rare Earth Chemistry and Physics, Chinese Academy of Sciences
文摘Y2O3： Er^3＋, Yb^3＋ nanoparticles were synthesized by a homogeneous precipitation method without and with different concentrations of EDTA 2Na. Upconversion luminescence spectra of the samples were studied under 980 nm laser excitation. The results of XRD showed that the obtained Y2O3：Er^3＋,Yb^3＋ nanoparticles were of a cubic structure. The average crystallite sizes calculated were in the range of 28-40 nm. Green and red upconversion emission were observed, and attributed to ^2H11/2,^4S3/2→^4I15/2 and ^4F9/2→^4I15/2 transitions of the ion, respectively. The ratio of the intensity of green emission to that of red emission drastically changed with a change in the EDTA 2Na concentration. In the sample synthesized without EDTA, the relative intensity of the green emission was weaker than that of the red emission. The relative intensities of green emission increased with the increased amount of EDTA 2Na used. The possible upconversion luminescence mechanisms were discussed.
文摘A series of TiO 2-MoO 3 nano-composite photocatalysts were prepared by supercritical fluid dry method(SCFD) and an impregnation technique with TiCl 4 and (NH 4) 6Mo 7O 24 ·4H 2O as the starting materials. The catalysts were characterized by the means of XRD, TEM and UV-Vis. Methyl orange was used as model compound for the evaluation of their catalytic activities. The results indicated that the photo-catalyst prepared by SCFD had the advantages of small size(12.84 nm), narrow distribution and good dispersivity. The presence of small amount of Mo in composite catalyst gives rise to the red shift of its absorbance wavelength, decrease of its energy gap and increase of the utility of visible light. Furthermore, higher surface acidity of the photo-catalyst was obtained as the result of the addition of MoO 3. Compared with pure TiO 2, the catalytic activity of the TiO 2-MoO 3 nano-composite photo-catalyst was improved significantly. As the doping concentration of the composite catalysts was controlled at 0.6%(molar percentage), 100% degradation of methyl orange was achieved with in 1.2 h irradiation time.
基金supported by the Natural Science Foundation of Henan Province (082300440130, 2008A180039, 2007150049)Startup Fund for Doctoral Program of Zhoukou Normal University
文摘The europium-doped LaF3 nanoparticles were prepared by refluxing method in glycerol/water mixture and characterized with X-ray diffraction（XRD）, field emission scanning electron microscopy（FE-SEM）, UV-vis diffuse reflectance spectrum, and photoluminescence spectra.The results of XRD indicated that the obtained LaF3：Eu^3＋ nanoparticles were well crystallized with a hexagonal structure.The FE-SEM image illustrated that the LaF3：Eu^3＋ nanoparticles were spherical with an average size around 30 nm.Under irradiation of UV light, the emission spectrum of LaF3：Eu^3＋ nanoparticles exhibited the characteristic line emissions arising from the 5D0→7FJ（J=1, 2, 3, 4） transitions of the Eu3＋ ions, with the dominating emission centered at 590 nm.In addition, the emissions from the 5D1 level could be clearly observed due to the low phonon energies（-350 cm^-1） of LaF3 matrix.The optimum doping concentration for LaF3：Eu3＋ nanoparticles was determined to be 20mol.%.
基金Project supported by International Visegrad Fund (51000547 (2010-2011))
文摘Mixed strontium-yttrium borate phosphor Sr3Y2（BO3）4 doped with Eu^3＋ ions was obtained by the sol-gel Pechini method. Crystal structure of the synthesized compound was analyzed by X-ray powder diffraction. Optimal conditions for the synthesis were found. Photophysical properties of the phosphor samples were investigated by collecting excitation and luminescence spectra as well as measuring lumi- nescence lifetime. Judd-Ofelt analysis showed that Eu^3＋ ions occupied Y^3＋ sites in the crystalline network. The studied compound showed a red emission with the quantum yield of 54%-55% and can be potentially used as phosphor for plasma display panels and luminescent tubes.
文摘在强光照射下,CdS量子点易发生光腐蚀现象,通过金属掺杂和复合的方式可以提高CdS的光催化性能和光稳定性。采用水热法合成了Zn掺杂CdS/g-C_(3)N_(4)复合纳米材料(Zn-CdS/g-C_(3)N_(4))。利用扫描电子显微镜(SEM)、透射电子显微镜(TEM)、X射线衍射(XRD)、X射线光电子能谱(XPS)和傅里叶变换红外光谱(FT-IR)等手段对Zn-CdS/g-C_(3)N_(4)复合材料的形貌、结构和组成等进行了表征。结果表明,Zn-CdS纳米颗粒附着在g-C_(3)N_(4)表面上,从而形成Zn-CdS/g-C_(3)N_(4)复合材料,且复合后材料带隙减小,光生电子-空穴复合率降低。在500 W Xe灯照射下,研究了Zn-CdS/g-C_(3)N_(4)对罗丹明B(RhB)的光催化降解性能。在最优条件下,光照40 min后,所制备的Zn-CdS/g-C_(3)N_(4)对RhB的光催化降解效率达99%。此外,所合成的Zn-CdS/g-C_(3)N_(4)复合材料光稳定性较高、可再生性好。这归因于Zn和Cd的协同作用以及与g-C_(3)N_(4)的复合,促进了光生载流子的分离和转移。
基金the National Natural Science Foundation of China(No.2 0 2 770 15 )
文摘Bi 2O 3 nanoparticles were prepared by means of ammonia precipitation, polyol mediated methods and microemulsion chemical method. The structure and properties of the as-prepared nanoparticles, having been submitted to a heat-treatment test at 750 ℃, were characterized by means of XRD, BET, XPS and UV-Vis absorption techniques. The photocatalytic oxidation reactions of benzene, toluene and xylene were used as the model reaction to measure the photocatalytic activity of Bi 2O 3 nanoparticles, respectively. The results show that the crystallite size of Bi 2O 3 prepared with different methods and calcined at 750 ℃ were 50.6, 38.5 and 31.5 nm, respectively. The photocatalytic activity of Bi 2O 3 nanoparticles prepared with the microemulsion chemical method was higher than that of the particles prepared with the polyol mediated method; and that of the particles prepared with the micromulsion chemical method was the highest among the three. The degradation rates of the three pollutants xylene, toluene and benzene decreased in sequence.
