This article presents a micro-structure tensor enhanced elasto-plastic finite element(FE)method to address strength anisotropy in three-dimensional(3D)soil slope stability analysis.The gravity increase method(GIM)is e...This article presents a micro-structure tensor enhanced elasto-plastic finite element(FE)method to address strength anisotropy in three-dimensional(3D)soil slope stability analysis.The gravity increase method(GIM)is employed to analyze the stability of 3D anisotropic soil slopes.The accuracy of the proposed method is first verified against the data in the literature.We then simulate the 3D soil slope with a straight slope surface and the convex and concave slope surfaces with a 90turning corner to study the 3D effect on slope stability and the failure mechanism under anisotropy conditions.Based on our numerical results,the end effect significantly impacts the failure mechanism and safety factor.Anisotropy degree notably affects the safety factor,with higher degrees leading to deeper landslides.For concave slopes,they can be approximated by straight slopes with suitable boundary conditions to assess their stability.Furthermore,a case study of the Saint-Alban test embankment A in Quebec,Canada,is provided to demonstrate the applicability of the proposed FE model.展开更多
The interaction between pile and soft soil of the passive pile group subjected to soil movement was analyzed with three-dimensional finite element model by using ANSYS software. The soil was assumed to be elastic-plas...The interaction between pile and soft soil of the passive pile group subjected to soil movement was analyzed with three-dimensional finite element model by using ANSYS software. The soil was assumed to be elastic-plastic complying with the Drucker-Prager yield criterion in the analysis. The large displacement of soil was considered and contact elements were used to evaluate the interaction between pile and soil. The influences of soil depth of layer and number of piles on the lateral pressure of the pile were investigated, and the lateral pressure distributions on the (2×1) pile group and on the (2×2) pile group were compared. The results show that the adjacent surcharge may result in significant lateral movement of the soft soil and considerable pressure on the pile. The pressure acting on the row near the surcharge is higher than that on the other row, due to the "barrier" and arching effects in pile groups. The passive load and its distribution should be taken into account in the design of the passive piles.展开更多
The transport of fluid, nutrients, and signaling molecules in the bone lacunar-canalicular system （LCS） is critical for osteocyte survival and function. We have applied the fluorescence recovery after photobleaching...The transport of fluid, nutrients, and signaling molecules in the bone lacunar-canalicular system （LCS） is critical for osteocyte survival and function. We have applied the fluorescence recovery after photobleaching （FRAP） approach to quantify load-induced fluid and solute transport in the LCS in situ, but the measurements were limited to cortical regions 30-50 μm underneath the periosteum due to the constrains of laser penetration. With this work, we aimed to expand our understanding of load-induced fluid and solute transport in both trabecular and cortical bone using a multiscaled image-based finite element analysis （FEA） approach. An intact murine tibia was first re-constructed from microCT images into a three-dimensional （3D） linear elastic FEA model, and the matrix deformations at various locations were calculated under axial loading. A segment of the above 3D model was then imported to the biphasic poroelasticity analysis platform （FEBio） to predict load-induced fluid pressure fields, and interstitial solute/fluid flows through LCS in both cortical and trabecular regions. Further, secondary flow effects such as the shear stress and/or drag force acting on osteocytes, the presumed mechano-sensors in bone, were derived using the previously developed ultrastructural model of Brinkman flow in the canaliculi. The material properties assumed in the FEA models were validated against previously obtained strain and FRAP transport data measured on the cortical cortex. Our results demonstrated the feasibility of this computational approach in estimating the fluid flux in the LCS and the cellular stimulation forces （shear and drag forces） for osteocytes in any cortical and trabecular bone locations, allowing further studies of how the activation of osteocytes correlates with in vivo functional bone formation. The study provides a promising platform to reveal potential cellular mechanisms underlying the anabolic power of exercises and physical activities in treating patients with skeletal deficiencies.展开更多
During recent years,the axial-flus PMSM with contra-rotating rotors has become a hot topic in academic research due to its high efficiency and simple structure.However,its back-EMF may be distorted under the condition...During recent years,the axial-flus PMSM with contra-rotating rotors has become a hot topic in academic research due to its high efficiency and simple structure.However,its back-EMF may be distorted under the condition of different angular positions.This paper investigates characteristics of the novel motor used for contra-propeller driving.Considering the torque ripple and current oscillation under unbalanced load condition,this paper analyzes the distorted back-EMF of the machine when its two rotors get different angular positions during rotating.The analysis results are validated by transient-magnetic 3-D FEA method,which the 3-D FEA software is used to model this motor and transient simulations are carried out to obtain its magnetic characteristic and main performances.A main focus is put on the back-EMF characteristic with different angular positions between the two rotors.Furthermore,the characteristic of torque production under unbalanced load is investigated.Finally,a prototype motor is fabricated to validate the analyses of this paper.展开更多
Objective： The biomechanical characters of the bone fracture of the man femoral hip joint under impact loads are explored. Methods ：A biosystem model of the man femoral hip joint by using the GE （ General Electric...Objective： The biomechanical characters of the bone fracture of the man femoral hip joint under impact loads are explored. Methods ：A biosystem model of the man femoral hip joint by using the GE （ General Electric） lightspeed multi-lay spiral CT is conducted. A 3D finite element model is established by employing the finite element software ANSYS. The FE analysis mainly concentrates on the effects of the impact directions arising from intense movements and the parenchyma on the femoral hip joint on the stress distributions of the proximal femur. Results：The parenchyma on the hip joint has relatively large relaxation effect on the impact loads. Conclusion：Effects of the angle δ of the impact load to the anterior direction and the angle γ of the impact load to the femur shaft on the bone fracture are given;δ has larger effect on the stress and strain distributions than the angle γ,which mainly represents the fracture of the upper femur including the femoral neck fracture when the posterolateral femur is impacted, consistent with the clinical resuits.展开更多
Objective: To study the memory biomechanical character of anatomic distal radius Nitinol memory connector (DRMC) in treating distal radius fracture. Methods: Establishing three dimensional model and finite element ana...Objective: To study the memory biomechanical character of anatomic distal radius Nitinol memory connector (DRMC) in treating distal radius fracture. Methods: Establishing three dimensional model and finite element analysis, we calculated the stress in and around the fracture faces when distal radius fracture was fixated with DRMC. Results: Axial holding stress produced by holding part of DRMC on distal radius was 14.66 MPa. The maximum stress of holding part was 40-70 MPa, the minimum stress was 3-7 MPa,and the stress of compression part was 20-40 MPa. Conclusion: The distribution of stress produced by DRMC around the fracture line is reasonable, and axial holding stress can help stabilize fracture during earlier period. The existence of longitudal compression and memory effect can transfer fixated disused section into developed section and enhance fracture healing.展开更多
A 3D femoral model was built to obtain the three-dimensional temperature distribution of femur and its surrounding tissues and provide references for clinical applications. According to the relationship between gray-v...A 3D femoral model was built to obtain the three-dimensional temperature distribution of femur and its surrounding tissues and provide references for clinical applications. According to the relationship between gray-value and material properties,the model was assigned with various materials to make sure that it is more similar to the real femur in geometry and physical properties. 3D temperature distribution is obtained by using finite element analysis software ANSYS 11. 0 on the basis of heat conduction theory,Laplace equation,Pennes bio-heat transfer equation,thermo physical parameters of bone tissues,the boundary condition,and initial conditions. Taken the asymmetry of the 3D distribution of temperature into account,it is necessary to adopt the heating method with multiple heat sources. This method can ensure that the temperature fields match well with the tumor tissues and kill the tumor cells efficiently under the condition of protecting the normal tissues from damage. The analysis results supply important guidance for determining the needle position and the needle number and controlling the intensity of heating.展开更多
Thin-film structures are widely used in industry due to their advantages in lightweight,flexibility and deployability.This paper investigates the wrinkling deformation pattern of square film subjected to in-plane tors...Thin-film structures are widely used in industry due to their advantages in lightweight,flexibility and deployability.This paper investigates the wrinkling deformation pattern of square film subjected to in-plane torsion through the post-buckling theory of shell,with the geometric nonlinear behavior derived by energy principle and analyzed with finite element method.An equal-sized experimental verification platform is designed and fabricated,and the wrinkling surface of polyimide film driven by rotary motor is reconstructed by 3D-digital image correlation measurement and verified with finite element simulation comparisons.Wrinkling region within the film expands continuously as the torsion proceeds,accompanied by multiple wrinkling configuration transitions throughout the complete evolutionary process.Due to the non-axial symmetry between structure and loading,significant discrepancies arise in amplitude,span and wavelength between different stripes,effects of thickness,torsion radius and pre-stretch on wrinkling pattern configuration are further discussed.This study can provide valuable references for understanding the wrinkling mechanism of hard film under complex torsion loading.展开更多
Applying stiffness migration method,a 3D finite element mechanical model is established to simulate the excavation and advance processes.By using 3D nonlinear finite element method,the tunnel boring machine(TBM) excav...Applying stiffness migration method,a 3D finite element mechanical model is established to simulate the excavation and advance processes.By using 3D nonlinear finite element method,the tunnel boring machine(TBM) excavation process is dynamically simulated to analyze the stress and strain field status of surrounding rock and segment.The maximum tensile stress of segment ring caused by tunnel construction mainly lies in arch bottom and presents zonal distribution.The stress increases slightly and limitedly in the course of excavation.The maximum and minimum displacements of segment,manifesting as zonal distribution,distribute in arch bottom and vault respectively.The displacements slightly increase with the advance of TBM and gradually tend to stability.展开更多
Based on the first-order shear deformation theory,a 3-node co-rotational triangular finite element formulation is developed for large deformation modeling of non-smooth,folded and multi-shell laminated composite struc...Based on the first-order shear deformation theory,a 3-node co-rotational triangular finite element formulation is developed for large deformation modeling of non-smooth,folded and multi-shell laminated composite structures.The two smaller components of the mid-surface normal vector of shell at a node are defined as nodal rotational variables in the co-rotational local coordinate system.In the global coordinate system,two smaller components of one vector,together with the smallest or second smallest component of another vector,of an orthogonal triad at a node on a non-smooth intersection of plates and/or shells are defined as rotational variables,whereas the two smaller components of the mid-surface normal vector at a node on the smooth part of the plate or shell(away from non-smooth intersections)are defined as rotational variables.All these vectorial rotational variables can be updated in an additive manner during an incremental solution procedure,and thus improve the computational efficiency in the nonlinear solution of these composite shell structures.Due to the commutativity of all nodal variables in calculating of the second derivatives of the local nodal variables with respect to global nodal variables,and the second derivatives of the strain energy functional with respect to local nodal variables,symmetric tangent stiffness matrices in local and global coordinate systems are obtained.To overcome shear locking,the assumed transverse shear strains obtained from the line-integration approach are employed.The reliability and computational accuracy of the present 3-node triangular shell finite element are verified through modeling two patch tests,several smooth and non-smooth laminated composite shells undergoing large displacements and large rotations.展开更多
Effective motors are crucial for driving astronomical telescopes,especially for those operating in Antarctica,where the harsh environment and operating conditions,including extreme low temperature,ice/snow accumulatio...Effective motors are crucial for driving astronomical telescopes,especially for those operating in Antarctica,where the harsh environment and operating conditions,including extreme low temperature,ice/snow accumulation,low power consumption,and unattended operation,introduce challenges to the design and development of motor drives.We present the design of a permanent magnet synchronous motor suitable for this environment,conducting a quantitative analysis on the impacts of cryogenic conditions on lubricant performance,differential thermal contraction of metallic components,and remanent flux density of neodymium iron boron(N52)permanent magnets.We also implement a labyrinth seal structure,combined with silicone sealing rings,to mitigate ice crystal intrusion risks.Finite element analysis and laboratory tests demonstrate a maximum torque output of 25 Nm.This kind of motor is used in the Antarctic 15 cm Near Infrared Telescope at Dome A,Antarctica.Operation data shows a total encoder feedback error of 0.0678"for the telescope control system with 15"s^(−1)tracking speed at−56.79°C.These results comprehensively validate the high reliability and precision of the motor under the extreme conditions of the polar environment.展开更多
Additive manufacturing(AM),adding materials layer by layer,can be used to produce objects of almost any shape or geometry.However,AM techniques cannot accurately build parts with large overhangs,especially for the lar...Additive manufacturing(AM),adding materials layer by layer,can be used to produce objects of almost any shape or geometry.However,AM techniques cannot accurately build parts with large overhangs,especially for the large features close to horizontal,hanging over the void.The overhangs will make the manufactured model deviate from the design model,which will result in the performance of the manufactured model that cannot satisfy the design requirements.In this paper,we will propose a new finite element(FE)analysis model that includes the manufacturing errors by mimicking the AM layer by layer construction process.In such FE model,an overhang coefficient is introduced to each FE,which is defined by the support elements in the lower layer.By mimicking the AM process from the bottom layer to the top layer,all the FE properties are updated based on their overhang coefficients,which makes the computational model be able to predict the manufactured model with manufacturing errors.The proposed model can be used to predict the performance of the AM objects in the design stage,which will help the designers to improve their design by the simulation results.展开更多
Crushing roller is one of the main parts of High-p re ssure Grinding Roller, which is a kind of high efficient ore crushing equipment. A kind of assembled roller, which is more convenient to renovate worn surface b y ...Crushing roller is one of the main parts of High-p re ssure Grinding Roller, which is a kind of high efficient ore crushing equipment. A kind of assembled roller, which is more convenient to renovate worn surface b y simply replacing segmented surface of the roller, was developed. The structura l models of assembled roller’s components were designed with SolidWorks softwar e based on feature modeling, these solid models of the roller were virtually ass embled. Through this work, not only was the assemble interference checked out so as to examine validity of the structure design, but also these solid models cou ld be recognized by COSMOS/Works software, through which the finite element an alysis can be done. Then the stress and displacement of the main shaft and sur face segment in two different working states were analyzed and detected quickly according to the analysis results with COSMOS/Works. In conclusion, the optimum clearance of 1.0～2.0 mm between concave-convex studded segments is determined to make the using life of assembled roller longer.展开更多
As permanent magnet motors and generators produce torque, vibration occurs through the small air gap due to the alternating magnetic forces created by the rotating permanent magnets and the current switching of the co...As permanent magnet motors and generators produce torque, vibration occurs through the small air gap due to the alternating magnetic forces created by the rotating permanent magnets and the current switching of the coils. The magnetic force can be calculated from the flux density by finite element methods and the Maxwell stress tensor in cy-lindrical coordinates. In this paper the magnetic flux density, the magnetic force and the torque of a real three dimen-sional brushless DC motor are simulated using Maxwell 3 D V 11.1.展开更多
<span style="font-family:Verdana;">Laser surface hardening is becoming one of the most successful heat treatment processes for improving wear and fatigue properties of steel parts. In this process, the...<span style="font-family:Verdana;">Laser surface hardening is becoming one of the most successful heat treatment processes for improving wear and fatigue properties of steel parts. In this process, the heating system parameters and the material properties have important effects on the achieved hardened surface characteristics. The control of these variables using predictive modeling strategies leads to the desired surface properties without following the fastidious trial and error method. However, when the dimensions of the surface to be treated are larger than the cross section of the laser beam, various laser scanning patterns can be used. Due to their effects on the hardened surface properties, the attributes of the selected scanning patterns become significant variables in the process. This paper presents numerical and experimental investigations of four scanning patterns for laser surface hardening of AISI 4340 steel. The investigations are based on exhaustive modelling and simulation efforts carried out using a 3D finite element thermal analysis and structured experimental study according to Taguchi method. The temperature distribution and the hardness profile attributes are used to evaluate the effects of heating parameters and patterns design parameters on the hardened surface characteristics. This is very useful for integrating the scanning patterns</span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">’</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;"> features in an efficient predictive modeling approach. A structured experimental design combined to improved statistical analysis tools </span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">is</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;"> used</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;"> to</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;"> assess the 3D model performance. The experiments are performed on a 3 kW Nd:Yag laser system. The modeling results exhibit a great agreement between the predicted and measured values for the hardened surface characteristics. The model evaluation reveal</span></span></span><span><span><span>s </span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">also its ability to provide not only accurate and robust predictions of the temperature distribution and the hardness profile as well an in-depth analysis of the effects of the process parameters.</span></span></span>展开更多
With superior structural integrity and design flexibility,3D woven fabrics exhibit unique potential in ballistic protection applications.However,the anisotropic yarn distribution renders traditional 3D woven fabrics s...With superior structural integrity and design flexibility,3D woven fabrics exhibit unique potential in ballistic protection applications.However,the anisotropic yarn distribution renders traditional 3D woven fabrics susceptible to fixed boundaries,which is not conducive to practical applications.Inspired by the motion characteristics of yarn structures,this study investigates a hybrid 3D woven fabric structure that incorporates interlayer warp yarns and normal yarns.Bending stiffness tests,yarn pull-out tests,and ballistic tests are conducted and compared with single-binding yarn structures.Utilizing a validated meso-finite element model,the dynamic deformation and energy absorption mechanisms of the hybrid configuration under impact are elucidated.The results demonstrate that synergistic interactions among various binding yarn structures maintain fabric stability in the absence of boundaries.Normal yarns inhibit horizontal slippage of warp yarns,while multi-layer warp yarns enhance resistance to weft yarn pull-out,thereby facilitating greater yarn participation in direct energy absorption.The hybrid structure exhibited the highest specific energy absorption(SEA)across different boundary conditions,with an average SEA increase of approximately 27%.These insights will facilitate the design of novel hybrid-structured 3D woven fabrics and inform the customization of lightweight protective materials.展开更多
In consideration of the contact between the steel spiral casing and the peripheral reinforced concrete, a nonlinear analysis for the combined bearing structure of the JinPing-I preloading filling spiral case has been ...In consideration of the contact between the steel spiral casing and the peripheral reinforced concrete, a nonlinear analysis for the combined bearing structure of the JinPing-I preloading filling spiral case has been made with ANSYS. Contrasts of the stress of the reinforcing bars, the biggest width of the crack and the outspread section of the crack has been made with the different parameters of preloading pressure and reinforcement scheme, resulting in a reasonable preloading pressure and reinforcement scheme. This conclusion has been applied to the spiral casing of JinPing-I hydropower station.展开更多
Within today＇s product development process, various FE-simulations （finite element） for the functional validation of the desired characteristics are made to avoid expensive testing with real components. Those simul...Within today＇s product development process, various FE-simulations （finite element） for the functional validation of the desired characteristics are made to avoid expensive testing with real components. Those simulations are performed with great effort for discretization, use of simulations conditions, like taking different non-linearities （i.e., material behavior, etc.） into account, to create meaningful results. Despite knowing the effects of deformations occurring during the production processes, always the non-deformed design model of a CAD-system （computer aided design） is used for the FE-simulations. It seems rather doubtful that further refinement of simulation methods makes sense, if the real manufactured geometry of the component is not considered for in the simulation. For an efficient exploit of the potential of simulation methods, an approach has been developed which offers a geometry model for simulation based on the existing CAD-model but with integrated production deviations as soon as a first prototype is at hand by adapting the FE-mesh to the real, 3D surface detected geometry.展开更多
Line heating process is a very complex phenomenon as a variety of factors affects the amount of residual deformations. Numerical thermal and mechanical analysis of line heating for prediction of residual deformation i...Line heating process is a very complex phenomenon as a variety of factors affects the amount of residual deformations. Numerical thermal and mechanical analysis of line heating for prediction of residual deformation is time consuming. In the present work dimensional analysis has been presented to obtain a new relationship between input parameters and resulting residual deformations during line heating process. The temperature distribution and residual deformations for 6 mm, 8 mm, 10 mm and 12 mm thick steel plates were numerically estimated and compared with experimental and published results. Extensive data generated through a validated FE model were used to find co-relationship between the input parameters and the resulting residual deformation by multiple regression analysis. The results obtained from the deformation equations developed in this work compared well with those of the FE analysis with a drop in the computation time in the order of 100 (computational time required for FE analysis is around 7 200 second to 9 000 seconds and where the time required for getting the residual deformation by developed equations is only 60 to 90 seconds).展开更多
Purpose:The fractures of anterior mandible are subject to severe torsional forces due to muscles acting in opposite directions.3D miniplate has been suggested as a good alternative by some researchers.However,finite e...Purpose:The fractures of anterior mandible are subject to severe torsional forces due to muscles acting in opposite directions.3D miniplate has been suggested as a good alternative by some researchers.However,finite element model(FEM)studies indicate that labio-inferior positioning of two miniplates perpendicular to each other offers better stability as compared to labial positioning.This study aims at combining the advantages of a single 3D miniplate and labio-inferior positioning of two conventional miniplates,which was assessed by finite element analysis along with a pilot clinical trial.Methods:Two FEM models were created using CT data of a 24-year-old patient with Angie class I occlusion:control model with labial plating and study model with labio-inferior plating.The models were processed with MIMICS.(materialise,Leuven,Belgium),CATIA.(Dassault Systemes)and finite element analysis softwares.Parameters adopted for analysis were(1)displacement(mm)of fracture fragments during each screw fixation,(2)lingual splay and post fixation stability of fracture fragments with masticatory load,and(3)stress distribution(MPa)across fracture fragments.Moreover,a pilot clinical trial including five patients with anterior mandible fracture was conducted.The fractures were managed by intraoral open reduction and 3D miniplate fixation in labio-inferior position.Intraoperative interfragmentary gap,post fixation lingual splay and radiographic fracture union and complications were assessed clinically.Results:Labio-inferior plating demonstrated less displacement(mm)of fracture fragments during screw fixation(0.059 vs.0.079)as well as after application of masticatory load(1.805 vs.1.860).Negligible lingual splay and less stress distribution(MPa)across fracture fragments(1.860 vs.1.847)were appreciated in the study group as compared to control group.Clinical trial support the favorable outcome related to intraoperative and postoperative assessment parameters.Conclusion:FEM analysis and clinical trial reveal better results with labio-inferior positioning of 3D miniplate when compared to labial positioning.展开更多
基金supported by the National Natural Science Foundation of China(Grant Nos.51890912,51979025 and 52011530189).
文摘This article presents a micro-structure tensor enhanced elasto-plastic finite element(FE)method to address strength anisotropy in three-dimensional(3D)soil slope stability analysis.The gravity increase method(GIM)is employed to analyze the stability of 3D anisotropic soil slopes.The accuracy of the proposed method is first verified against the data in the literature.We then simulate the 3D soil slope with a straight slope surface and the convex and concave slope surfaces with a 90turning corner to study the 3D effect on slope stability and the failure mechanism under anisotropy conditions.Based on our numerical results,the end effect significantly impacts the failure mechanism and safety factor.Anisotropy degree notably affects the safety factor,with higher degrees leading to deeper landslides.For concave slopes,they can be approximated by straight slopes with suitable boundary conditions to assess their stability.Furthermore,a case study of the Saint-Alban test embankment A in Quebec,Canada,is provided to demonstrate the applicability of the proposed FE model.
基金Project(50378036) supported by the National Natural Science Foundation of China
文摘The interaction between pile and soft soil of the passive pile group subjected to soil movement was analyzed with three-dimensional finite element model by using ANSYS software. The soil was assumed to be elastic-plastic complying with the Drucker-Prager yield criterion in the analysis. The large displacement of soil was considered and contact elements were used to evaluate the interaction between pile and soil. The influences of soil depth of layer and number of piles on the lateral pressure of the pile were investigated, and the lateral pressure distributions on the (2×1) pile group and on the (2×2) pile group were compared. The results show that the adjacent surcharge may result in significant lateral movement of the soft soil and considerable pressure on the pile. The pressure acting on the row near the surcharge is higher than that on the other row, due to the "barrier" and arching effects in pile groups. The passive load and its distribution should be taken into account in the design of the passive piles.
基金supported by grants from NIH (P30GM103333 and RO1AR054385 to LW)China CSC fellowship (to LF)DOD W81XWH-13-1-0148 (to XLL)
文摘The transport of fluid, nutrients, and signaling molecules in the bone lacunar-canalicular system （LCS） is critical for osteocyte survival and function. We have applied the fluorescence recovery after photobleaching （FRAP） approach to quantify load-induced fluid and solute transport in the LCS in situ, but the measurements were limited to cortical regions 30-50 μm underneath the periosteum due to the constrains of laser penetration. With this work, we aimed to expand our understanding of load-induced fluid and solute transport in both trabecular and cortical bone using a multiscaled image-based finite element analysis （FEA） approach. An intact murine tibia was first re-constructed from microCT images into a three-dimensional （3D） linear elastic FEA model, and the matrix deformations at various locations were calculated under axial loading. A segment of the above 3D model was then imported to the biphasic poroelasticity analysis platform （FEBio） to predict load-induced fluid pressure fields, and interstitial solute/fluid flows through LCS in both cortical and trabecular regions. Further, secondary flow effects such as the shear stress and/or drag force acting on osteocytes, the presumed mechano-sensors in bone, were derived using the previously developed ultrastructural model of Brinkman flow in the canaliculi. The material properties assumed in the FEA models were validated against previously obtained strain and FRAP transport data measured on the cortical cortex. Our results demonstrated the feasibility of this computational approach in estimating the fluid flux in the LCS and the cellular stimulation forces （shear and drag forces） for osteocytes in any cortical and trabecular bone locations, allowing further studies of how the activation of osteocytes correlates with in vivo functional bone formation. The study provides a promising platform to reveal potential cellular mechanisms underlying the anabolic power of exercises and physical activities in treating patients with skeletal deficiencies.
基金This work was supported in part by the National Key R&D Program of China(No.2017YFB1300900)the Natural Science Foundation of China under Grant 51577052,51707062.
文摘During recent years,the axial-flus PMSM with contra-rotating rotors has become a hot topic in academic research due to its high efficiency and simple structure.However,its back-EMF may be distorted under the condition of different angular positions.This paper investigates characteristics of the novel motor used for contra-propeller driving.Considering the torque ripple and current oscillation under unbalanced load condition,this paper analyzes the distorted back-EMF of the machine when its two rotors get different angular positions during rotating.The analysis results are validated by transient-magnetic 3-D FEA method,which the 3-D FEA software is used to model this motor and transient simulations are carried out to obtain its magnetic characteristic and main performances.A main focus is put on the back-EMF characteristic with different angular positions between the two rotors.Furthermore,the characteristic of torque production under unbalanced load is investigated.Finally,a prototype motor is fabricated to validate the analyses of this paper.
文摘Objective： The biomechanical characters of the bone fracture of the man femoral hip joint under impact loads are explored. Methods ：A biosystem model of the man femoral hip joint by using the GE （ General Electric） lightspeed multi-lay spiral CT is conducted. A 3D finite element model is established by employing the finite element software ANSYS. The FE analysis mainly concentrates on the effects of the impact directions arising from intense movements and the parenchyma on the femoral hip joint on the stress distributions of the proximal femur. Results：The parenchyma on the hip joint has relatively large relaxation effect on the impact loads. Conclusion：Effects of the angle δ of the impact load to the anterior direction and the angle γ of the impact load to the femur shaft on the bone fracture are given;δ has larger effect on the stress and strain distributions than the angle γ,which mainly represents the fracture of the upper femur including the femoral neck fracture when the posterolateral femur is impacted, consistent with the clinical resuits.
文摘Objective: To study the memory biomechanical character of anatomic distal radius Nitinol memory connector (DRMC) in treating distal radius fracture. Methods: Establishing three dimensional model and finite element analysis, we calculated the stress in and around the fracture faces when distal radius fracture was fixated with DRMC. Results: Axial holding stress produced by holding part of DRMC on distal radius was 14.66 MPa. The maximum stress of holding part was 40-70 MPa, the minimum stress was 3-7 MPa,and the stress of compression part was 20-40 MPa. Conclusion: The distribution of stress produced by DRMC around the fracture line is reasonable, and axial holding stress can help stabilize fracture during earlier period. The existence of longitudal compression and memory effect can transfer fixated disused section into developed section and enhance fracture healing.
基金Sponsored by the National Natural Science Foundation of China(Grant No.61272387)the Program for New Century Excellent Talents in University(Grant No.NCET-13-0756)the Distinguished Young Scientists Funds of Heilongjiang Province(Grant No.JC201302)
文摘A 3D femoral model was built to obtain the three-dimensional temperature distribution of femur and its surrounding tissues and provide references for clinical applications. According to the relationship between gray-value and material properties,the model was assigned with various materials to make sure that it is more similar to the real femur in geometry and physical properties. 3D temperature distribution is obtained by using finite element analysis software ANSYS 11. 0 on the basis of heat conduction theory,Laplace equation,Pennes bio-heat transfer equation,thermo physical parameters of bone tissues,the boundary condition,and initial conditions. Taken the asymmetry of the 3D distribution of temperature into account,it is necessary to adopt the heating method with multiple heat sources. This method can ensure that the temperature fields match well with the tumor tissues and kill the tumor cells efficiently under the condition of protecting the normal tissues from damage. The analysis results supply important guidance for determining the needle position and the needle number and controlling the intensity of heating.
基金supported by the National Natural Science Foundation of China(Grant No.12472347).
文摘Thin-film structures are widely used in industry due to their advantages in lightweight,flexibility and deployability.This paper investigates the wrinkling deformation pattern of square film subjected to in-plane torsion through the post-buckling theory of shell,with the geometric nonlinear behavior derived by energy principle and analyzed with finite element method.An equal-sized experimental verification platform is designed and fabricated,and the wrinkling surface of polyimide film driven by rotary motor is reconstructed by 3D-digital image correlation measurement and verified with finite element simulation comparisons.Wrinkling region within the film expands continuously as the torsion proceeds,accompanied by multiple wrinkling configuration transitions throughout the complete evolutionary process.Due to the non-axial symmetry between structure and loading,significant discrepancies arise in amplitude,span and wavelength between different stripes,effects of thickness,torsion radius and pre-stretch on wrinkling pattern configuration are further discussed.This study can provide valuable references for understanding the wrinkling mechanism of hard film under complex torsion loading.
基金Supported by National Natural Science Foundation of China(No.90815019)National Key Basic Research Program of China("973" Program,No.2007CB714101)Key Project in the National Science and Technology Pillar Program during the Eleventh Five-Year Plan Period(No.2006BAB04A13)
文摘Applying stiffness migration method,a 3D finite element mechanical model is established to simulate the excavation and advance processes.By using 3D nonlinear finite element method,the tunnel boring machine(TBM) excavation process is dynamically simulated to analyze the stress and strain field status of surrounding rock and segment.The maximum tensile stress of segment ring caused by tunnel construction mainly lies in arch bottom and presents zonal distribution.The stress increases slightly and limitedly in the course of excavation.The maximum and minimum displacements of segment,manifesting as zonal distribution,distribute in arch bottom and vault respectively.The displacements slightly increase with the advance of TBM and gradually tend to stability.
基金This work was supported by National Natural Science Foundation of China under Grant 11672266.
文摘Based on the first-order shear deformation theory,a 3-node co-rotational triangular finite element formulation is developed for large deformation modeling of non-smooth,folded and multi-shell laminated composite structures.The two smaller components of the mid-surface normal vector of shell at a node are defined as nodal rotational variables in the co-rotational local coordinate system.In the global coordinate system,two smaller components of one vector,together with the smallest or second smallest component of another vector,of an orthogonal triad at a node on a non-smooth intersection of plates and/or shells are defined as rotational variables,whereas the two smaller components of the mid-surface normal vector at a node on the smooth part of the plate or shell(away from non-smooth intersections)are defined as rotational variables.All these vectorial rotational variables can be updated in an additive manner during an incremental solution procedure,and thus improve the computational efficiency in the nonlinear solution of these composite shell structures.Due to the commutativity of all nodal variables in calculating of the second derivatives of the local nodal variables with respect to global nodal variables,and the second derivatives of the strain energy functional with respect to local nodal variables,symmetric tangent stiffness matrices in local and global coordinate systems are obtained.To overcome shear locking,the assumed transverse shear strains obtained from the line-integration approach are employed.The reliability and computational accuracy of the present 3-node triangular shell finite element are verified through modeling two patch tests,several smooth and non-smooth laminated composite shells undergoing large displacements and large rotations.
基金supported by the Space Debris Resear-ch Project,China(KJSP2020010102)the NationalKey R&D Program of China(2022YFC2807300).
文摘Effective motors are crucial for driving astronomical telescopes,especially for those operating in Antarctica,where the harsh environment and operating conditions,including extreme low temperature,ice/snow accumulation,low power consumption,and unattended operation,introduce challenges to the design and development of motor drives.We present the design of a permanent magnet synchronous motor suitable for this environment,conducting a quantitative analysis on the impacts of cryogenic conditions on lubricant performance,differential thermal contraction of metallic components,and remanent flux density of neodymium iron boron(N52)permanent magnets.We also implement a labyrinth seal structure,combined with silicone sealing rings,to mitigate ice crystal intrusion risks.Finite element analysis and laboratory tests demonstrate a maximum torque output of 25 Nm.This kind of motor is used in the Antarctic 15 cm Near Infrared Telescope at Dome A,Antarctica.Operation data shows a total encoder feedback error of 0.0678"for the telescope control system with 15"s^(−1)tracking speed at−56.79°C.These results comprehensively validate the high reliability and precision of the motor under the extreme conditions of the polar environment.
基金This work has been supported by National Natural Science Foundation of China(51705158)Guangdong Basic and Applied Basic Research Foundation(2019A1515011783)the Fundamental Research Funds for the Central Universities(2018MS45).
文摘Additive manufacturing(AM),adding materials layer by layer,can be used to produce objects of almost any shape or geometry.However,AM techniques cannot accurately build parts with large overhangs,especially for the large features close to horizontal,hanging over the void.The overhangs will make the manufactured model deviate from the design model,which will result in the performance of the manufactured model that cannot satisfy the design requirements.In this paper,we will propose a new finite element(FE)analysis model that includes the manufacturing errors by mimicking the AM layer by layer construction process.In such FE model,an overhang coefficient is introduced to each FE,which is defined by the support elements in the lower layer.By mimicking the AM process from the bottom layer to the top layer,all the FE properties are updated based on their overhang coefficients,which makes the computational model be able to predict the manufactured model with manufacturing errors.The proposed model can be used to predict the performance of the AM objects in the design stage,which will help the designers to improve their design by the simulation results.
文摘Crushing roller is one of the main parts of High-p re ssure Grinding Roller, which is a kind of high efficient ore crushing equipment. A kind of assembled roller, which is more convenient to renovate worn surface b y simply replacing segmented surface of the roller, was developed. The structura l models of assembled roller’s components were designed with SolidWorks softwar e based on feature modeling, these solid models of the roller were virtually ass embled. Through this work, not only was the assemble interference checked out so as to examine validity of the structure design, but also these solid models cou ld be recognized by COSMOS/Works software, through which the finite element an alysis can be done. Then the stress and displacement of the main shaft and sur face segment in two different working states were analyzed and detected quickly according to the analysis results with COSMOS/Works. In conclusion, the optimum clearance of 1.0～2.0 mm between concave-convex studded segments is determined to make the using life of assembled roller longer.
文摘As permanent magnet motors and generators produce torque, vibration occurs through the small air gap due to the alternating magnetic forces created by the rotating permanent magnets and the current switching of the coils. The magnetic force can be calculated from the flux density by finite element methods and the Maxwell stress tensor in cy-lindrical coordinates. In this paper the magnetic flux density, the magnetic force and the torque of a real three dimen-sional brushless DC motor are simulated using Maxwell 3 D V 11.1.
文摘<span style="font-family:Verdana;">Laser surface hardening is becoming one of the most successful heat treatment processes for improving wear and fatigue properties of steel parts. In this process, the heating system parameters and the material properties have important effects on the achieved hardened surface characteristics. The control of these variables using predictive modeling strategies leads to the desired surface properties without following the fastidious trial and error method. However, when the dimensions of the surface to be treated are larger than the cross section of the laser beam, various laser scanning patterns can be used. Due to their effects on the hardened surface properties, the attributes of the selected scanning patterns become significant variables in the process. This paper presents numerical and experimental investigations of four scanning patterns for laser surface hardening of AISI 4340 steel. The investigations are based on exhaustive modelling and simulation efforts carried out using a 3D finite element thermal analysis and structured experimental study according to Taguchi method. The temperature distribution and the hardness profile attributes are used to evaluate the effects of heating parameters and patterns design parameters on the hardened surface characteristics. This is very useful for integrating the scanning patterns</span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">’</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;"> features in an efficient predictive modeling approach. A structured experimental design combined to improved statistical analysis tools </span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">is</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;"> used</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;"> to</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;"> assess the 3D model performance. The experiments are performed on a 3 kW Nd:Yag laser system. The modeling results exhibit a great agreement between the predicted and measured values for the hardened surface characteristics. The model evaluation reveal</span></span></span><span><span><span>s </span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">also its ability to provide not only accurate and robust predictions of the temperature distribution and the hardness profile as well an in-depth analysis of the effects of the process parameters.</span></span></span>
基金supports from National Key R&D Program for Young Scientists of China(No.2022YFC3080900)the opening project of State Key Laboratory of Explosion Science and Safety Protection,Beijing Institute of Technology(No.KFJJ25-25M).
文摘With superior structural integrity and design flexibility,3D woven fabrics exhibit unique potential in ballistic protection applications.However,the anisotropic yarn distribution renders traditional 3D woven fabrics susceptible to fixed boundaries,which is not conducive to practical applications.Inspired by the motion characteristics of yarn structures,this study investigates a hybrid 3D woven fabric structure that incorporates interlayer warp yarns and normal yarns.Bending stiffness tests,yarn pull-out tests,and ballistic tests are conducted and compared with single-binding yarn structures.Utilizing a validated meso-finite element model,the dynamic deformation and energy absorption mechanisms of the hybrid configuration under impact are elucidated.The results demonstrate that synergistic interactions among various binding yarn structures maintain fabric stability in the absence of boundaries.Normal yarns inhibit horizontal slippage of warp yarns,while multi-layer warp yarns enhance resistance to weft yarn pull-out,thereby facilitating greater yarn participation in direct energy absorption.The hybrid structure exhibited the highest specific energy absorption(SEA)across different boundary conditions,with an average SEA increase of approximately 27%.These insights will facilitate the design of novel hybrid-structured 3D woven fabrics and inform the customization of lightweight protective materials.
文摘In consideration of the contact between the steel spiral casing and the peripheral reinforced concrete, a nonlinear analysis for the combined bearing structure of the JinPing-I preloading filling spiral case has been made with ANSYS. Contrasts of the stress of the reinforcing bars, the biggest width of the crack and the outspread section of the crack has been made with the different parameters of preloading pressure and reinforcement scheme, resulting in a reasonable preloading pressure and reinforcement scheme. This conclusion has been applied to the spiral casing of JinPing-I hydropower station.
文摘Within today＇s product development process, various FE-simulations （finite element） for the functional validation of the desired characteristics are made to avoid expensive testing with real components. Those simulations are performed with great effort for discretization, use of simulations conditions, like taking different non-linearities （i.e., material behavior, etc.） into account, to create meaningful results. Despite knowing the effects of deformations occurring during the production processes, always the non-deformed design model of a CAD-system （computer aided design） is used for the FE-simulations. It seems rather doubtful that further refinement of simulation methods makes sense, if the real manufactured geometry of the component is not considered for in the simulation. For an efficient exploit of the potential of simulation methods, an approach has been developed which offers a geometry model for simulation based on the existing CAD-model but with integrated production deviations as soon as a first prototype is at hand by adapting the FE-mesh to the real, 3D surface detected geometry.
文摘Line heating process is a very complex phenomenon as a variety of factors affects the amount of residual deformations. Numerical thermal and mechanical analysis of line heating for prediction of residual deformation is time consuming. In the present work dimensional analysis has been presented to obtain a new relationship between input parameters and resulting residual deformations during line heating process. The temperature distribution and residual deformations for 6 mm, 8 mm, 10 mm and 12 mm thick steel plates were numerically estimated and compared with experimental and published results. Extensive data generated through a validated FE model were used to find co-relationship between the input parameters and the resulting residual deformation by multiple regression analysis. The results obtained from the deformation equations developed in this work compared well with those of the FE analysis with a drop in the computation time in the order of 100 (computational time required for FE analysis is around 7 200 second to 9 000 seconds and where the time required for getting the residual deformation by developed equations is only 60 to 90 seconds).
文摘Purpose:The fractures of anterior mandible are subject to severe torsional forces due to muscles acting in opposite directions.3D miniplate has been suggested as a good alternative by some researchers.However,finite element model(FEM)studies indicate that labio-inferior positioning of two miniplates perpendicular to each other offers better stability as compared to labial positioning.This study aims at combining the advantages of a single 3D miniplate and labio-inferior positioning of two conventional miniplates,which was assessed by finite element analysis along with a pilot clinical trial.Methods:Two FEM models were created using CT data of a 24-year-old patient with Angie class I occlusion:control model with labial plating and study model with labio-inferior plating.The models were processed with MIMICS.(materialise,Leuven,Belgium),CATIA.(Dassault Systemes)and finite element analysis softwares.Parameters adopted for analysis were(1)displacement(mm)of fracture fragments during each screw fixation,(2)lingual splay and post fixation stability of fracture fragments with masticatory load,and(3)stress distribution(MPa)across fracture fragments.Moreover,a pilot clinical trial including five patients with anterior mandible fracture was conducted.The fractures were managed by intraoral open reduction and 3D miniplate fixation in labio-inferior position.Intraoperative interfragmentary gap,post fixation lingual splay and radiographic fracture union and complications were assessed clinically.Results:Labio-inferior plating demonstrated less displacement(mm)of fracture fragments during screw fixation(0.059 vs.0.079)as well as after application of masticatory load(1.805 vs.1.860).Negligible lingual splay and less stress distribution(MPa)across fracture fragments(1.860 vs.1.847)were appreciated in the study group as compared to control group.Clinical trial support the favorable outcome related to intraoperative and postoperative assessment parameters.Conclusion:FEM analysis and clinical trial reveal better results with labio-inferior positioning of 3D miniplate when compared to labial positioning.
