A novel SnO2-based gas anode was developed for aluminum electrolysis in molten cryolite at 850 ＆#176;C to reduce energy consumption and decrease CO2 emissions. Hydrogen was introduced into the anode, participating in...A novel SnO2-based gas anode was developed for aluminum electrolysis in molten cryolite at 850 ＆#176;C to reduce energy consumption and decrease CO2 emissions. Hydrogen was introduced into the anode, participating in the anode reaction. Carbon and aluminum were used as the cathode and reference electrodes, respectively. Cyclic voltammetry was applied in the cell to investigate the electrochemical behavior of oxygen ion on platinum and SnO2-based materials. The potential for oxygen evolution on these electrode materials was determined. Then, galvanostatic electrolysis was performed on the gas anode, showing a significant depolarization effect （a decrease of ~0.8 V of the anode potential） after the introduction of hydrogen, compared with no gas introduction or the introduction of argon. The results indicate the involvement of hydrogen in the anode reaction （three-phase-boundary reaction including gas, electrolyte and electrode） and give the possibility for the utilization of reducing gas anodes for aluminum electrolysis.展开更多
A series of SnO2‐based catalysts modified by Mn, Zr, Ti and Pb oxides with a Sn/M （M=Mn, Zr, Ti and Pb） molar ratio of 9/1 were prepared by a co‐precipitation method and used for CH4 and CO oxidation. The Mn3＋, ...A series of SnO2‐based catalysts modified by Mn, Zr, Ti and Pb oxides with a Sn/M （M=Mn, Zr, Ti and Pb） molar ratio of 9/1 were prepared by a co‐precipitation method and used for CH4 and CO oxidation. The Mn3＋, Zr4＋, Ti4＋and Pb4＋cations are incorporated into the lattice of tetragonal rutile SnO2 to form a solid solution structure. As a consequence, the surface area and thermal stability of the catalysts are improved. Moreover, the oxygen species of the modified catalysts become easier to be reduced. Therefore, the oxidation activity over the catalysts was improved, except for the one modified by Pb oxide. Manganese oxide demonstrates the best promotional effects for SnO2. Using an X‐ray diffraction extrapolation method, the lattice capacity of SnO2 for Mn2O3 was 0.135 g Mn2O3/g SnO2, which indicates that to form stable solid solution, only 21%Sn4＋cations in the lattice can be maximally replaced by Mn3＋. If the amount of Mn3＋cations is over the capacity, Mn2O3 will be formed, which is not favorable for the activity of the catalysts. The Sn rich samples with only Sn‐Mn solid solution phase show higher activity than the ones with excess Mn2O3 species.展开更多
We investigated the influence of soaking time on the semi-conductivity and nonlinear electrical properties of TiO2- based varistor ceramic samples. We used a single sintering process and fabricated six disk samples of...We investigated the influence of soaking time on the semi-conductivity and nonlinear electrical properties of TiO2- based varistor ceramic samples. We used a single sintering process and fabricated six disk samples of （Sr, Bi, Si, Ta）-doped TiO2- based varistor ceramics sintered at 1 250℃ for 0.5 h, 1.0 h, 2.0 h, 3.0 h, 4.0 h, and 5.0 h, respectively. The samples were characterized by X-ray diffraction, breakdown voltage, and complex impedance. The results show that as the soaking time increases from 0.5 h to 5.0 h, the breakdown voltage drops before rising while the nonlinear coefficient increases and then decreases. We suggest that, considering both grain semi-conductivity and nonlinear electrical properties of the TiO2-based varistor ceramics, the optimal soaking time is between 2.0 h and 3.0 h.展开更多
To improve both oxygen evolution efficiency and stability at high temperatures, Mn, Mn+Mo, Mn+Mo+V, and Mn+Fe+V oxide electrodes were prepared on a Ti substrate, with an intermediate layer of IrO_2, by an anodic depos...To improve both oxygen evolution efficiency and stability at high temperatures, Mn, Mn+Mo, Mn+Mo+V, and Mn+Fe+V oxide electrodes were prepared on a Ti substrate, with an intermediate layer of IrO_2, by an anodic deposition method. The crystal structure, surface morphology, pore size distribution, specific surface area, and voltammetric charge were then characterized for each electrode. The results demonstrated that for Mn-O electrodes, the preferential orientation of the(100) crystal plane and the mesopore structure played negative roles in the oxygen evolution reaction. On the basis of the electrocatalytic properties of MnO2-based electrodes in seawater, the outer surface voltammetric charge at a scan rate of 500 mV·s-1 was shown to effectively indicate whether oxygen evolution reactions were preferred over chlorine evolution reactions. The Mn-O electrode exhibited oxygen evolution efficiency of only 47.27%, whereas the Mn+Mo, Mn+Mo+V and Mn+Fe+V oxide electrodes displayed oxygen evolution efficiency of nearly 100%. This means that adding Mo, V, and Fe elements to the electrode can improve its crystal structure and morphology as well as further enhancing its oxygen evolution efficiency.展开更多
Slag movement on SiO2-based prism refractories in different slag systems was observed. The cross section shape evolution mechanism was discussed. Two types of shape evolution appear. For PbO-SiO2 slag whose surface te...Slag movement on SiO2-based prism refractories in different slag systems was observed. The cross section shape evolution mechanism was discussed. Two types of shape evolution appear. For PbO-SiO2 slag whose surface tension improves with SiO2 concentration, slag film flows up along four edges under axial Marangoni shear force and wettability. Then, it flows down along four lateral faces under gravity. Corrosion rate at edges is larger than that on lateral faces due to different SiO2 solubilities of ascending and descending flow. Prism cross section shape changes from square to round. For FetO-SiO2 slag whose surface tension reduces with the increase of SiO2 concentration, slag film flows up under the inflence of wettability. Then, it flows down under Marangoni shear force and gravity. Compared to four edges, slag is mainly up and down on four lateral faces due to larger surface tension and size. So, prism cross section shape keeps square.展开更多
MoS 2-based composite coatings were deposited with the nano-compound unbalanced plasma plating technique. The effects of processing parameters and working environments on the tribological properties of the coatings w...MoS 2-based composite coatings were deposited with the nano-compound unbalanced plasma plating technique. The effects of processing parameters and working environments on the tribological properties of the coatings were examined by the drilling experiments and XPS. The distances between substrate and Ti target, Ti content and deposition pressure were varied in order to determine the optimum conditions for producing lubricious, long-lasting MoS 2-based coatings. It is found that the tribological performance of TiN-MoS 2 coating decreases rapidly in humid air but the humid-resistant property of TiN-MoS 2/Ti coating improves evidently.It is indicated that the humid-resistantance property and the abrasion durability of MoS 2-based coatings can be enhanced markedly by adding Ti with a certain contents.展开更多
Tin disulfide(SnS_(2)),due to large interlayer spacing and high theoretical capacity,is regarded as a prospective anode material for lithium-ion batteries.Nevertheless,the poor electron conductivity of SnS_(2) and hug...Tin disulfide(SnS_(2)),due to large interlayer spacing and high theoretical capacity,is regarded as a prospective anode material for lithium-ion batteries.Nevertheless,the poor electron conductivity of SnS_(2) and huge volumetric change during the lithiation/delithiation process lead to a rapid capacity decay of the battery,hindering its commercialization.To address these issues,herein,SnS_(2) is in-situ grown on the surface of carbon nanotubes(CNT)and then encapsulated with a layer of porous amorphous carbon(CNT/SnS_(2)@C)by simple solvothermal and further carbonization treatment.The synergistic effect of CNT and porous carbon layer not only enhances the electrical co nductivity of SnS_(2) but also limits the huge volumetric change to avoid the pulverization and detachment of SnS_(2).Density functional theo ry calculations show that CNT/SnS_(2)@C has high Li^(+)adsorption and lithium storage capacity achieving high reaction kinetics.Consequently,cells with the CNT/SnS_(2)@C anode exhibit a high lithium storage capacity of 837mAh/g after 100 cycles at 0.1 A/g and retaining a capacity of 529.8 mAh/g under 1.0 A/g after 1000 cycles.This study provides a fundamental understanding of the electrochemical processes and beneficial guidance to design high-performance SnS_(2)-based anodes for LIBs.展开更多
Some active metal oxides(Al_(2)O_(3),TiO_(2),and Cr_(2)O_(3))were selected as dopants to the Al_(2)O_(3)-based ceramic shells for investment casting of K417G superalloy.The effects of dopant types and contents(0,2,5,a...Some active metal oxides(Al_(2)O_(3),TiO_(2),and Cr_(2)O_(3))were selected as dopants to the Al_(2)O_(3)-based ceramic shells for investment casting of K417G superalloy.The effects of dopant types and contents(0,2,5,and 8 wt.%)on the wettability and interfacial reaction between the alloy and shell were investigated by a sessile-drop experiment.The results show that increasing the Al_(2)O_(3) doping contents(0−8 wt.%)reduces the porosity(21.74%−10.08%)and roughness(3.22−1.34μm)of the shell surface.The increase in Cr_(2)O_(3) dopant content(2−8 wt.%)further exacerbates the interfacial reaction,leading to an increase in the thickness of the reaction layer(2.6−3.1μm)and a decrease in the wetting angle(93.9°−91.0°).The addition of Al_(2)O_(3) and TiO_(2) dopants leads to the formation of Al_(2)TiO_(5) composite oxides in the reaction products,which effectively inhibits the interfacial reaction.The increase in TiO_(2) dopant contents(0−8 wt.%)further promotes the formation of Al_(2)TiO_(5),which decreases the thickness of the interfacial reaction layer(3.9−1.2μm)and increases the wetting angle(95.0°−103.8°).The introduced dopants enhance the packing density of the shell surface,while simultaneously suppress the diffusion of active metal elements from the alloy matrix to the interface.展开更多
A unique discontinuous lamellar microstructure of titanium alloys consisting of lamellar colonies at prior β-Ti grain boundaries and internal interwoven α-laths is prepared by a TiH_(2)-based powder metallurgy metho...A unique discontinuous lamellar microstructure of titanium alloys consisting of lamellar colonies at prior β-Ti grain boundaries and internal interwoven α-laths is prepared by a TiH_(2)-based powder metallurgy method.The α-variants get various crystallographic orientations and become discontinuous during vacuum annealing at 700℃.Remarkably,nanoscale phase δ-TiH compound layers are generated between α-laths and β-strips,so that dislocations are piled up at the α/δ/βinterfaces during tensile deformation.This leads to dislocation slips being confined to individual α-laths,with differentslips and particularly pyramidal<c+a>slips being activated.The efficiency of wavy slip is promoted and the work hardening rate is enhanced.Finally,the combined effect of dispersed micro-shear bands and lath distortions is considered contributive for alleviating the stress concentration at grain boundaries,resulting in a high-promising synergy of enhanced ultimate tensile strength of 1080 MPa and good elongation to fracture of 13.6%.展开更多
Catalytic activity and hydrothermal stability are both crucial for the application of the selective catalytic reduction of NO_(x)with NH_(3)(NH_(3)-SCR)catalyst in diesel vehicles.In this study,a tin(Sn)-modified Ce-N...Catalytic activity and hydrothermal stability are both crucial for the application of the selective catalytic reduction of NO_(x)with NH_(3)(NH_(3)-SCR)catalyst in diesel vehicles.In this study,a tin(Sn)-modified Ce-Nb mixed-oxide catalyst was synthesized as an NH_(3)-SCR catalyst for NO_(x)emission control.After the intro-duction of Sn,both the NH_(3)-SCR activity and the hydrothermal stability of the catalyst were remarkably promoted.Even after hydrothermal aging at 1000℃,the developed Ce_(1)Sn_(2)Nb_(1)O_(x)catalyst achieved more than 90%NO_(x)conversion at 325-500℃.Various methods,including N2-physisorption,X-ray diffraction,in-situ high-temperature X-ray diffraction,high-resolution transmission electron microscopy,X-ray pho-toelectron spectroscopy,X-ray absorption fine-structure spectroscopy,temperature-programmed reduc-tion of hydrogen,temperature-programmed desorption of ammonia,and density functional theory calculations were used to investigate the promotional effects induced by the Sn species.The characteri-zation results showed that the addition of Sn not only promoted the formation of the Ce-Nb active phase but also improved its thermal stability,contributing to the excellent NH_(3)-SCR performance and hydrothermal stability.This study provides an excellent sintering-resistance catalyst for the application of diesel engine NO_(x)emission control.展开更多
Neuromorphic computing devices leveraging HfO_(2) and ZrO_(2) materials have recently garnered significant attention due to their potential for brain-inspired computing systems.In this study,we present a novel trilaye...Neuromorphic computing devices leveraging HfO_(2) and ZrO_(2) materials have recently garnered significant attention due to their potential for brain-inspired computing systems.In this study,we present a novel trilayer Pt/HfO_(2)/ZrO_(2-x)/HfO_(2)/TiN memristor,engineered with a ZrO_(2-x) oxygen vacancy reservoir(OVR)layer fabricated via radio frequency(RF)sputtering under controlled oxygen ambient.The incorporation of the ZrO_(2-x) OVR layer enables enhanced resistive switching characteristics,including a high ON/OFF ratio(∼8000),excellent uniformity,robust data retention(>105 s),and multilevel storage capabilities.Furthermore,the memristor demonstrates superior synaptic plasticity with linear long-term potentiation(LTP)and depression(LTD),achieving low non-linearity values of 1.36(LTP)and 0.66(LTD),and a recognition accuracy of 95.3%in an MNIST dataset simulation.The unique properties of the ZrO_(2-x) layer,particularly its ability to act as a dynamic oxygen vacancy reservoir,significantly enhance synaptic performance by stabilizing oxygen vacancy migration.These findings establish the OVR-trilayer memristor as a promising candidate for future neuromorphic computing and high-performance memory applications.展开更多
Al_(2)O_(3)-based eutectic ceramics are considered as promising candidates for ultra-high-temperature structural materials due to their exceptional thermal stability and mechanical properties.Nonetheless,several chall...Al_(2)O_(3)-based eutectic ceramics are considered as promising candidates for ultra-high-temperature structural materials due to their exceptional thermal stability and mechanical properties.Nonetheless,several challenges must be overcome before they can be widely used.This paper reviews in detail the tailoring of microstructure from the aspect of process parameters,the updated knowledge gained in microstructure(crystallographic orientation,high-resolution interfacial structures)and the latest means of optimizing eutectic microstructure(seed-induced method,introducing low-energy grain boundaries and high-entropy phase).Additionally,the paper explores future techniques for the fabrication of bulk ceramic materials and effective toughening approaches.This review highlights the achievements made especially in the last 15 years,current limitations in Al_(2)O_(3)-based eutectic ceramics,and offers comprehensive insights and strategic guidance for further mechanical breakthroughs.展开更多
The reaction behavior between CaO–Al_(2)O_(3)–La_(2)O_(3)-based slags and La-bearing FeCrAl melt was quantitatively characterized,which was further compared with the reaction behavior of CaO–SiO_(2)-based slags.Bas...The reaction behavior between CaO–Al_(2)O_(3)–La_(2)O_(3)-based slags and La-bearing FeCrAl melt was quantitatively characterized,which was further compared with the reaction behavior of CaO–SiO_(2)-based slags.Based on this,the new type of mold flux for La-bearing FeCrAl alloy continuous casting was designed and its basic properties were evaluated.The results showed that the order of reaction degree of fluxing agents in CaO–Al_(2)O_(3)–La_(2)O_(3)-based slags is(Na_(2)O)>(B_(2)O_(3))>(Li_(2)O),and the percentages of mass change of fluxing agents were 85.8,54.29 and 42.35 wt.%,respectively.Moreover,the addition of(Li_(2)O)and(Na_(2)O)promoted the reaction between(CaO)and[Al],and the reaction degree of the former was weaker than that of the latter,which was due to the greater effect of(Na_(2)O)on the activity of(CaO)and(Al_(2)O_(3))than(Li_(2)O).Compared with the reactivity of CaO–SiO_(2)-based slags,the percentages of mass change of Al and La caused by slag–steel reaction decreased by 10.63–14.36 and 39.78–50.49 wt.%,respectively.The percentages of mass change of(Al_(2)O_(3)),(La_(2)O_(3))and(CaO)in slags highest increased by 17.71,17.98,and 7.81 wt.%,respectively.The reactivity of CaO–Al_(2)O_(3)–La_(2)O_(3)-based slags was significantly weakened.Ultimately,the new type of mold flux was designed and the composition range was determined.The fundamental properties of new mold flux basically meet the theoretical requirements for La-bearing FeCrAl alloy continuous casting.展开更多
SnO2-based varistor samples doped with Co2O3,Nb2O5 and Cr2O3 were prepared by ball-mixed oxide method.The microstructure,nonlinear I-V characteristic and surge current performances of these samples were investigated.T...SnO2-based varistor samples doped with Co2O3,Nb2O5 and Cr2O3 were prepared by ball-mixed oxide method.The microstructure,nonlinear I-V characteristic and surge current performances of these samples were investigated.This paper mainly focused on the dependence of the residual voltage ratio behavior of SnO2-based varistors on Nb2O5 addition,different factors influencing the residual voltage ratio in different concentration of Nb2O5 were analyzed.The Nb2O5 addition influences its residual voltage ratio by changing the grain size,forming defects(especially the free electrons) and cumulative effect.The measured results indicated that the optimally obtained sample with 0.07mol% Nb2O5 possesses the lowest residual voltage ratio of 1.86,the corresponding nonlinear coefficient and the threshold electric field are 42.6 and 364.6 V/mm,respectively.展开更多
Materials in the transition metal dichalcogenide family, including WS2, MoS2, WSe2, and MoSe2, etc., have captured a substantial amount of attention due to their remarkable nonlinearities and optoelectronic properties...Materials in the transition metal dichalcogenide family, including WS2, MoS2, WSe2, and MoSe2, etc., have captured a substantial amount of attention due to their remarkable nonlinearities and optoelectronic properties.Compared with WS2 and MoS2, the monolayered MoTe2 owns a smaller direct bandgap of 1.1 eV. It is beneficial for the applications in broadband absorption. In this letter, using the magnetron sputtering technique, MoTe2 is deposited on the surface of the tapered fiber to be assembled into the saturable absorber. We first implement the MoTe2-based Q-switched fiber laser operating at the wavelength of 1559 nm. The minimum pulse duration and signal-to-noise ratio are 677 ns and 63 dB, respectively. Moreover, the output power of 25 mW is impressive compared with previous work. We believe that MoTe2 is a promising 2D material for ultrafast photonic devices in the high-power Q-switched fiber lasers.展开更多
In this work, we study the influence of the average crystallite size and dopant oxide on the reducibility of CeO2-based nanomaterials. Samples were prepared from commercial Gd2O3-, Sm2O3- and Y2O3-doped CeO2 powders b...In this work, we study the influence of the average crystallite size and dopant oxide on the reducibility of CeO2-based nanomaterials. Samples were prepared from commercial Gd2O3-, Sm2O3- and Y2O3-doped CeO2 powders by calcination at different temperatures ranging between 400°C and 900°C and characterized by X-ray powder diffraction, transmission electron microscopy and BET specific surface area. The reducibility of the samples was analyzed by temperature-programmed reduction and in situ dispersive X-ray absorption spectroscopy techniques. Our results clearly demonstrate that samples treated at lower temperatures, of smallest average crystallite size and highest specific surface areas, exhibit the best performance, while Gd2O3-doped ceria materials display higher reducibility than Sm2O3- and Y2O3-doped CeO2.展开更多
Thermoelectric materials,enabling the directing conversion between heat and electricity,are one of the promising candidates for overcoming environmental pollution and the upcoming energy shortage caused by the over-co...Thermoelectric materials,enabling the directing conversion between heat and electricity,are one of the promising candidates for overcoming environmental pollution and the upcoming energy shortage caused by the over-consumption of fossil fuels.Bi2Te3-based alloys are the classical thermoelectric materials working near room temperature.Due to the intensive theoretical investigations and experimental demonstrations,significant progress has been achieved to enhance the thermoelectric performance of Bi2Te3-based thermoelectric materials.In this review,we first explored the fundamentals of thermoelectric effect and derived the equations for thermoelectric properties.On this basis,we studied the effect of material parameters on thermoelectric properties.Then,we analyzed the features of Bi2Te3-based thermoelectric materials,including the lattice defects,anisotropic behavior and the strong bipolar conduction at relatively high temperature.Then we accordingly summarized the strategies for enhancing the thermoelectric performance,including point defect engineering,texture alignment,and band gap enlargement.Moreover,we highlighted the progress in decreasing thermal conductivity using nanostructures fabricated by solution grown method,ball milling,and melt spinning.Lastly,we employed modeling analysis to uncover the principles of anisotropy behavior and the achieved enhancement in Bi2Te3,which will enlighten the enhancement of thermoelectric performance in broader materials展开更多
Advanced high-strength steels (AHSSs) have been gradually applied to modern auto industry, as they have the advantages of improving the steel strength and lightening the car weight, which not only ensures the safety b...Advanced high-strength steels (AHSSs) have been gradually applied to modern auto industry, as they have the advantages of improving the steel strength and lightening the car weight, which not only ensures the safety but also saves the energy. However, the high-aluminum (Al) content in AHSSs may react with SiO2 in conventional CaO-SiO2-based mold flux during the process of continuous casting, which leads to the deterioration of the mold flux properties and a poor slab quality. Then, the non-reactive CaO-Al2O3-based mold flux was proposed and has been developing for the casting process of high-Al steels, but there are some problems of low consumption and insufficient lubrication that need to be solved. Thus, previous researches on the effect of each component on the properties of CaO-Al2O3-based mold flux were systematically summarized, and the situation of plant trials on CaO-Al2O3-based mold flux was evaluated. The results indicated that the proposed CaO-Al2O3-based mold fluxes could avoid the slag-metal reaction problems;however, the problems of lubri-cation, crystallization and heat transfer issues still exist. Therefore, tremendous works still need to be conducted for the development of new generation of CaO-Al2O3-based mold flux system. The review was performed aiming to provide a technical guidance for designing and optimizing CaO-Al2O3-based mold flux system that meets the demand of the continuous casting process of high-Al steels.展开更多
Herein,we review the significant of ordered macroporous(OM)TiO_(2)-based catalysts for boosting pho-tocatalytic CO_(2)reduction.Based on the need to improve the three key factors of photogenerated charge separation ef...Herein,we review the significant of ordered macroporous(OM)TiO_(2)-based catalysts for boosting pho-tocatalytic CO_(2)reduction.Based on the need to improve the three key factors of photogenerated charge separation eficiency,solar energy utilization and CO_(2)adsorption rate during the conversion of CO_(2)to H_(2)O,we summarized five modification measures:including doping ions into OM TiO_(2),introducing sec-ond semiconductor coupling and noble metal nanoparticles for fabricating multiple Z-scheme heterojunc-tions,constructing hierarchical pore and carbon-loaded OM TiO_(2)materials,which effectively enhance the absorption rate of visible light,the separation rate of electrons-hole pairs and the selection of multiple active sites.The OM structured TiO_(2)-based photocatalysts solve the single or multiple key factors for en-hancing photocatalytic performances during CO_(2)conversion.The catalytic mechanism and pathways of OM structured TiO_(2)-based photocatalysts for CO_(2)reduction are discussed and summarized.It provides new insights on the development of high-efficient catalyst for photocatalytic CO_(2)conversion to solar fu-els.展开更多
A new technology was developed to recover multiple valuable elements from the spent Al2O3-based catalyst by X-ray phase analysis and exploratory experiments. The experimental results show that in the condition of roas...A new technology was developed to recover multiple valuable elements from the spent Al2O3-based catalyst by X-ray phase analysis and exploratory experiments. The experimental results show that in the condition of roasting temperature of 750℃ and roasting time of 30 min, molar ratio of Na2O to Al2O3 of 1.2, the leaching rates of alumina, vanadium and molybdenum in the spent catalyst are 97.2%, 95.8% and 98.9%, respectively. Vanadium and molybdenum in sodium aluminate solution can be recovered by precipitators A and B, and the precipitation rates of vanadium and molybdenum are 94.8% and 92.6%. Al（OH）3 was prepared from sodium aluminate solution in the carbonation decomposition process, and the purity of Al2O3 is 99.9% after calcination, the recovery of alumina reaches 90.6% in the whole process; the Ni-Co concentrate was leached by sulfuric acid, a nickel recovery of 98.2% and cobalt recovery over 98.5% can be obtained under the experimental condition of 30% H2SO4, 80℃, reaction time 4 h, mass ratio of liquid to solid 8, stirring rate 800r/min.展开更多
基金Project(51404001)supported by the National Natural Science Foundation of ChinaProject([2014]1685)supported by the Scientific Research Foundation for the Returned Overseas Chinese Scholars,Ministry of Education,China
文摘A novel SnO2-based gas anode was developed for aluminum electrolysis in molten cryolite at 850 ＆#176;C to reduce energy consumption and decrease CO2 emissions. Hydrogen was introduced into the anode, participating in the anode reaction. Carbon and aluminum were used as the cathode and reference electrodes, respectively. Cyclic voltammetry was applied in the cell to investigate the electrochemical behavior of oxygen ion on platinum and SnO2-based materials. The potential for oxygen evolution on these electrode materials was determined. Then, galvanostatic electrolysis was performed on the gas anode, showing a significant depolarization effect （a decrease of ~0.8 V of the anode potential） after the introduction of hydrogen, compared with no gas introduction or the introduction of argon. The results indicate the involvement of hydrogen in the anode reaction （three-phase-boundary reaction including gas, electrolyte and electrode） and give the possibility for the utilization of reducing gas anodes for aluminum electrolysis.
基金supported by the National Natural Science Foundation of China (21263015,21567016 and 21503106)the Education Department Foundation of Jiangxi Province (KJLD14005 and GJJ150016)the Natural Science Foundation of Jiangxi Province (20142BAB213013 and 20151BBE50006),which are greatly acknowledged by the authors~~
文摘A series of SnO2‐based catalysts modified by Mn, Zr, Ti and Pb oxides with a Sn/M （M=Mn, Zr, Ti and Pb） molar ratio of 9/1 were prepared by a co‐precipitation method and used for CH4 and CO oxidation. The Mn3＋, Zr4＋, Ti4＋and Pb4＋cations are incorporated into the lattice of tetragonal rutile SnO2 to form a solid solution structure. As a consequence, the surface area and thermal stability of the catalysts are improved. Moreover, the oxygen species of the modified catalysts become easier to be reduced. Therefore, the oxidation activity over the catalysts was improved, except for the one modified by Pb oxide. Manganese oxide demonstrates the best promotional effects for SnO2. Using an X‐ray diffraction extrapolation method, the lattice capacity of SnO2 for Mn2O3 was 0.135 g Mn2O3/g SnO2, which indicates that to form stable solid solution, only 21%Sn4＋cations in the lattice can be maximally replaced by Mn3＋. If the amount of Mn3＋cations is over the capacity, Mn2O3 will be formed, which is not favorable for the activity of the catalysts. The Sn rich samples with only Sn‐Mn solid solution phase show higher activity than the ones with excess Mn2O3 species.
基金Funded by the Natural Science Foundation of China (No. 50872001 and No. 50642038)the Scientific Research Foundation of Education Ministry of Anhui Province (No. 2005KJ224 and No. KJ2007B132)the Graduate Student Innovation Programs of Anhui University (No. 20072006)
文摘We investigated the influence of soaking time on the semi-conductivity and nonlinear electrical properties of TiO2- based varistor ceramic samples. We used a single sintering process and fabricated six disk samples of （Sr, Bi, Si, Ta）-doped TiO2- based varistor ceramics sintered at 1 250℃ for 0.5 h, 1.0 h, 2.0 h, 3.0 h, 4.0 h, and 5.0 h, respectively. The samples were characterized by X-ray diffraction, breakdown voltage, and complex impedance. The results show that as the soaking time increases from 0.5 h to 5.0 h, the breakdown voltage drops before rising while the nonlinear coefficient increases and then decreases. We suggest that, considering both grain semi-conductivity and nonlinear electrical properties of the TiO2-based varistor ceramics, the optimal soaking time is between 2.0 h and 3.0 h.
基金Funded by National Natural Science Foundation of China(No.51301070)Scientific and Technological Project of Henan Province(No.182102210068)
文摘To improve both oxygen evolution efficiency and stability at high temperatures, Mn, Mn+Mo, Mn+Mo+V, and Mn+Fe+V oxide electrodes were prepared on a Ti substrate, with an intermediate layer of IrO_2, by an anodic deposition method. The crystal structure, surface morphology, pore size distribution, specific surface area, and voltammetric charge were then characterized for each electrode. The results demonstrated that for Mn-O electrodes, the preferential orientation of the(100) crystal plane and the mesopore structure played negative roles in the oxygen evolution reaction. On the basis of the electrocatalytic properties of MnO2-based electrodes in seawater, the outer surface voltammetric charge at a scan rate of 500 mV·s-1 was shown to effectively indicate whether oxygen evolution reactions were preferred over chlorine evolution reactions. The Mn-O electrode exhibited oxygen evolution efficiency of only 47.27%, whereas the Mn+Mo, Mn+Mo+V and Mn+Fe+V oxide electrodes displayed oxygen evolution efficiency of nearly 100%. This means that adding Mo, V, and Fe elements to the electrode can improve its crystal structure and morphology as well as further enhancing its oxygen evolution efficiency.
基金Projects(U1738101,51804023)supported by the National Natural Science Foundation of ChinaProjects(FRF-TP-18-007A1,FRF-MP-18-007)supported by Fundamental Research Funds for the Central Universities,ChinaProject(2019M650489)supported by China Postdoctoral Science Foundation
文摘Slag movement on SiO2-based prism refractories in different slag systems was observed. The cross section shape evolution mechanism was discussed. Two types of shape evolution appear. For PbO-SiO2 slag whose surface tension improves with SiO2 concentration, slag film flows up along four edges under axial Marangoni shear force and wettability. Then, it flows down along four lateral faces under gravity. Corrosion rate at edges is larger than that on lateral faces due to different SiO2 solubilities of ascending and descending flow. Prism cross section shape changes from square to round. For FetO-SiO2 slag whose surface tension reduces with the increase of SiO2 concentration, slag film flows up under the inflence of wettability. Then, it flows down under Marangoni shear force and gravity. Compared to four edges, slag is mainly up and down on four lateral faces due to larger surface tension and size. So, prism cross section shape keeps square.
基金FundedbytheNationalNaturalScienceFoundationofChi na (No .90 2 0 6 0 2 2 )
文摘MoS 2-based composite coatings were deposited with the nano-compound unbalanced plasma plating technique. The effects of processing parameters and working environments on the tribological properties of the coatings were examined by the drilling experiments and XPS. The distances between substrate and Ti target, Ti content and deposition pressure were varied in order to determine the optimum conditions for producing lubricious, long-lasting MoS 2-based coatings. It is found that the tribological performance of TiN-MoS 2 coating decreases rapidly in humid air but the humid-resistant property of TiN-MoS 2/Ti coating improves evidently.It is indicated that the humid-resistantance property and the abrasion durability of MoS 2-based coatings can be enhanced markedly by adding Ti with a certain contents.
基金the financial support from the Australian Research CouncilCentre for Materials Science,Queensland University of Technology。
文摘Tin disulfide(SnS_(2)),due to large interlayer spacing and high theoretical capacity,is regarded as a prospective anode material for lithium-ion batteries.Nevertheless,the poor electron conductivity of SnS_(2) and huge volumetric change during the lithiation/delithiation process lead to a rapid capacity decay of the battery,hindering its commercialization.To address these issues,herein,SnS_(2) is in-situ grown on the surface of carbon nanotubes(CNT)and then encapsulated with a layer of porous amorphous carbon(CNT/SnS_(2)@C)by simple solvothermal and further carbonization treatment.The synergistic effect of CNT and porous carbon layer not only enhances the electrical co nductivity of SnS_(2) but also limits the huge volumetric change to avoid the pulverization and detachment of SnS_(2).Density functional theo ry calculations show that CNT/SnS_(2)@C has high Li^(+)adsorption and lithium storage capacity achieving high reaction kinetics.Consequently,cells with the CNT/SnS_(2)@C anode exhibit a high lithium storage capacity of 837mAh/g after 100 cycles at 0.1 A/g and retaining a capacity of 529.8 mAh/g under 1.0 A/g after 1000 cycles.This study provides a fundamental understanding of the electrochemical processes and beneficial guidance to design high-performance SnS_(2)-based anodes for LIBs.
基金supported by the National Natural Science Foundation of China (No. 52374292)China Baowu Low Carbon Metallurgy Innovation Foundation, China (No. BWLCF202309)the Natural Science Foundation of Changsha City, China (No. KQ2208271)。
文摘Some active metal oxides(Al_(2)O_(3),TiO_(2),and Cr_(2)O_(3))were selected as dopants to the Al_(2)O_(3)-based ceramic shells for investment casting of K417G superalloy.The effects of dopant types and contents(0,2,5,and 8 wt.%)on the wettability and interfacial reaction between the alloy and shell were investigated by a sessile-drop experiment.The results show that increasing the Al_(2)O_(3) doping contents(0−8 wt.%)reduces the porosity(21.74%−10.08%)and roughness(3.22−1.34μm)of the shell surface.The increase in Cr_(2)O_(3) dopant content(2−8 wt.%)further exacerbates the interfacial reaction,leading to an increase in the thickness of the reaction layer(2.6−3.1μm)and a decrease in the wetting angle(93.9°−91.0°).The addition of Al_(2)O_(3) and TiO_(2) dopants leads to the formation of Al_(2)TiO_(5) composite oxides in the reaction products,which effectively inhibits the interfacial reaction.The increase in TiO_(2) dopant contents(0−8 wt.%)further promotes the formation of Al_(2)TiO_(5),which decreases the thickness of the interfacial reaction layer(3.9−1.2μm)and increases the wetting angle(95.0°−103.8°).The introduced dopants enhance the packing density of the shell surface,while simultaneously suppress the diffusion of active metal elements from the alloy matrix to the interface.
基金financially supported by the National Natural Science Foundation of China(Nos.52301145,52275329)the Applied Basic Research Program of Liaoning Province,China(No.2023JH2/101300158)+1 种基金the Fundamental Research Fund for the Central Universities,China(No.N2202010)the Key Research Programs of High Education Institutions in Henan Province,China(No.24A430017).
文摘A unique discontinuous lamellar microstructure of titanium alloys consisting of lamellar colonies at prior β-Ti grain boundaries and internal interwoven α-laths is prepared by a TiH_(2)-based powder metallurgy method.The α-variants get various crystallographic orientations and become discontinuous during vacuum annealing at 700℃.Remarkably,nanoscale phase δ-TiH compound layers are generated between α-laths and β-strips,so that dislocations are piled up at the α/δ/βinterfaces during tensile deformation.This leads to dislocation slips being confined to individual α-laths,with differentslips and particularly pyramidal<c+a>slips being activated.The efficiency of wavy slip is promoted and the work hardening rate is enhanced.Finally,the combined effect of dispersed micro-shear bands and lath distortions is considered contributive for alleviating the stress concentration at grain boundaries,resulting in a high-promising synergy of enhanced ultimate tensile strength of 1080 MPa and good elongation to fracture of 13.6%.
基金supported by the National Natural Science Foundation of China(52225004 and 22276202)the National Key Research and Development Program of China(2022YFC3701804)the Youth Innovation Promotion Association of Chinese Academy of Sciences(2019045).
文摘Catalytic activity and hydrothermal stability are both crucial for the application of the selective catalytic reduction of NO_(x)with NH_(3)(NH_(3)-SCR)catalyst in diesel vehicles.In this study,a tin(Sn)-modified Ce-Nb mixed-oxide catalyst was synthesized as an NH_(3)-SCR catalyst for NO_(x)emission control.After the intro-duction of Sn,both the NH_(3)-SCR activity and the hydrothermal stability of the catalyst were remarkably promoted.Even after hydrothermal aging at 1000℃,the developed Ce_(1)Sn_(2)Nb_(1)O_(x)catalyst achieved more than 90%NO_(x)conversion at 325-500℃.Various methods,including N2-physisorption,X-ray diffraction,in-situ high-temperature X-ray diffraction,high-resolution transmission electron microscopy,X-ray pho-toelectron spectroscopy,X-ray absorption fine-structure spectroscopy,temperature-programmed reduc-tion of hydrogen,temperature-programmed desorption of ammonia,and density functional theory calculations were used to investigate the promotional effects induced by the Sn species.The characteri-zation results showed that the addition of Sn not only promoted the formation of the Ce-Nb active phase but also improved its thermal stability,contributing to the excellent NH_(3)-SCR performance and hydrothermal stability.This study provides an excellent sintering-resistance catalyst for the application of diesel engine NO_(x)emission control.
基金financially supported by the National Research Foundation of Korea(no.NRF-2021R1A2C2010781)grant funded by the Korean Government(Ministry of Science and ICT)Korea Institute for Advancement of Technology(KIAT)grant funded by the Korea Government(MOTIE)(no.P0012451,The Competency Development Program for Industry Specialist)Korea Government(MOTIE)(no.P0020966,HRD Program for Industrial Innovation).
文摘Neuromorphic computing devices leveraging HfO_(2) and ZrO_(2) materials have recently garnered significant attention due to their potential for brain-inspired computing systems.In this study,we present a novel trilayer Pt/HfO_(2)/ZrO_(2-x)/HfO_(2)/TiN memristor,engineered with a ZrO_(2-x) oxygen vacancy reservoir(OVR)layer fabricated via radio frequency(RF)sputtering under controlled oxygen ambient.The incorporation of the ZrO_(2-x) OVR layer enables enhanced resistive switching characteristics,including a high ON/OFF ratio(∼8000),excellent uniformity,robust data retention(>105 s),and multilevel storage capabilities.Furthermore,the memristor demonstrates superior synaptic plasticity with linear long-term potentiation(LTP)and depression(LTD),achieving low non-linearity values of 1.36(LTP)and 0.66(LTD),and a recognition accuracy of 95.3%in an MNIST dataset simulation.The unique properties of the ZrO_(2-x) layer,particularly its ability to act as a dynamic oxygen vacancy reservoir,significantly enhance synaptic performance by stabilizing oxygen vacancy migration.These findings establish the OVR-trilayer memristor as a promising candidate for future neuromorphic computing and high-performance memory applications.
基金financially supported by the National Natural Science Foundation of China(No.52171046)National Natural Science Foundation of China-key programme(No.52234010)the Fundamental Research Funds for the Central Universities and Shaanxi Provincial Key Science and Technology Innovation Team(No.2023-CX-TD-14).
文摘Al_(2)O_(3)-based eutectic ceramics are considered as promising candidates for ultra-high-temperature structural materials due to their exceptional thermal stability and mechanical properties.Nonetheless,several challenges must be overcome before they can be widely used.This paper reviews in detail the tailoring of microstructure from the aspect of process parameters,the updated knowledge gained in microstructure(crystallographic orientation,high-resolution interfacial structures)and the latest means of optimizing eutectic microstructure(seed-induced method,introducing low-energy grain boundaries and high-entropy phase).Additionally,the paper explores future techniques for the fabrication of bulk ceramic materials and effective toughening approaches.This review highlights the achievements made especially in the last 15 years,current limitations in Al_(2)O_(3)-based eutectic ceramics,and offers comprehensive insights and strategic guidance for further mechanical breakthroughs.
基金supported by the National Natural Science Foundation of China(Grant Nos.52174321,52274339 and 52074186).
文摘The reaction behavior between CaO–Al_(2)O_(3)–La_(2)O_(3)-based slags and La-bearing FeCrAl melt was quantitatively characterized,which was further compared with the reaction behavior of CaO–SiO_(2)-based slags.Based on this,the new type of mold flux for La-bearing FeCrAl alloy continuous casting was designed and its basic properties were evaluated.The results showed that the order of reaction degree of fluxing agents in CaO–Al_(2)O_(3)–La_(2)O_(3)-based slags is(Na_(2)O)>(B_(2)O_(3))>(Li_(2)O),and the percentages of mass change of fluxing agents were 85.8,54.29 and 42.35 wt.%,respectively.Moreover,the addition of(Li_(2)O)and(Na_(2)O)promoted the reaction between(CaO)and[Al],and the reaction degree of the former was weaker than that of the latter,which was due to the greater effect of(Na_(2)O)on the activity of(CaO)and(Al_(2)O_(3))than(Li_(2)O).Compared with the reactivity of CaO–SiO_(2)-based slags,the percentages of mass change of Al and La caused by slag–steel reaction decreased by 10.63–14.36 and 39.78–50.49 wt.%,respectively.The percentages of mass change of(Al_(2)O_(3)),(La_(2)O_(3))and(CaO)in slags highest increased by 17.71,17.98,and 7.81 wt.%,respectively.The reactivity of CaO–Al_(2)O_(3)–La_(2)O_(3)-based slags was significantly weakened.Ultimately,the new type of mold flux was designed and the composition range was determined.The fundamental properties of new mold flux basically meet the theoretical requirements for La-bearing FeCrAl alloy continuous casting.
基金supported by the National Natural Science Foundations of China (Grants Nos 50425721 and 50737001)
文摘SnO2-based varistor samples doped with Co2O3,Nb2O5 and Cr2O3 were prepared by ball-mixed oxide method.The microstructure,nonlinear I-V characteristic and surge current performances of these samples were investigated.This paper mainly focused on the dependence of the residual voltage ratio behavior of SnO2-based varistors on Nb2O5 addition,different factors influencing the residual voltage ratio in different concentration of Nb2O5 were analyzed.The Nb2O5 addition influences its residual voltage ratio by changing the grain size,forming defects(especially the free electrons) and cumulative effect.The measured results indicated that the optimally obtained sample with 0.07mol% Nb2O5 possesses the lowest residual voltage ratio of 1.86,the corresponding nonlinear coefficient and the threshold electric field are 42.6 and 364.6 V/mm,respectively.
基金supported by the National Natural Science Foundation of China(Grant Nos.11674036,11078022,and 61378040)the Beijing Youth Top-notch Talent Support Program(Grant No.2017000026833ZK08)the Fund of State Key Laboratory of Information Photonics and Optical Communications(Beijing University of Posts and Telecommunications,Grant Nos.IPOC2016ZT04 and IPOC2017ZZ05)
文摘Materials in the transition metal dichalcogenide family, including WS2, MoS2, WSe2, and MoSe2, etc., have captured a substantial amount of attention due to their remarkable nonlinearities and optoelectronic properties.Compared with WS2 and MoS2, the monolayered MoTe2 owns a smaller direct bandgap of 1.1 eV. It is beneficial for the applications in broadband absorption. In this letter, using the magnetron sputtering technique, MoTe2 is deposited on the surface of the tapered fiber to be assembled into the saturable absorber. We first implement the MoTe2-based Q-switched fiber laser operating at the wavelength of 1559 nm. The minimum pulse duration and signal-to-noise ratio are 677 ns and 63 dB, respectively. Moreover, the output power of 25 mW is impressive compared with previous work. We believe that MoTe2 is a promising 2D material for ultrafast photonic devices in the high-power Q-switched fiber lasers.
文摘In this work, we study the influence of the average crystallite size and dopant oxide on the reducibility of CeO2-based nanomaterials. Samples were prepared from commercial Gd2O3-, Sm2O3- and Y2O3-doped CeO2 powders by calcination at different temperatures ranging between 400°C and 900°C and characterized by X-ray powder diffraction, transmission electron microscopy and BET specific surface area. The reducibility of the samples was analyzed by temperature-programmed reduction and in situ dispersive X-ray absorption spectroscopy techniques. Our results clearly demonstrate that samples treated at lower temperatures, of smallest average crystallite size and highest specific surface areas, exhibit the best performance, while Gd2O3-doped ceria materials display higher reducibility than Sm2O3- and Y2O3-doped CeO2.
基金Project supported by the Australian Research CouncilZhi-Gang Chen thanks the USQ start-up grantstrategic research grant
文摘Thermoelectric materials,enabling the directing conversion between heat and electricity,are one of the promising candidates for overcoming environmental pollution and the upcoming energy shortage caused by the over-consumption of fossil fuels.Bi2Te3-based alloys are the classical thermoelectric materials working near room temperature.Due to the intensive theoretical investigations and experimental demonstrations,significant progress has been achieved to enhance the thermoelectric performance of Bi2Te3-based thermoelectric materials.In this review,we first explored the fundamentals of thermoelectric effect and derived the equations for thermoelectric properties.On this basis,we studied the effect of material parameters on thermoelectric properties.Then,we analyzed the features of Bi2Te3-based thermoelectric materials,including the lattice defects,anisotropic behavior and the strong bipolar conduction at relatively high temperature.Then we accordingly summarized the strategies for enhancing the thermoelectric performance,including point defect engineering,texture alignment,and band gap enlargement.Moreover,we highlighted the progress in decreasing thermal conductivity using nanostructures fabricated by solution grown method,ball milling,and melt spinning.Lastly,we employed modeling analysis to uncover the principles of anisotropy behavior and the achieved enhancement in Bi2Te3,which will enlighten the enhancement of thermoelectric performance in broader materials
基金National Natural Science Foundation of China(U1760202,51661130154)the Newton Advanced fellowship(NA 150320)is greatly acknowledged.
文摘Advanced high-strength steels (AHSSs) have been gradually applied to modern auto industry, as they have the advantages of improving the steel strength and lightening the car weight, which not only ensures the safety but also saves the energy. However, the high-aluminum (Al) content in AHSSs may react with SiO2 in conventional CaO-SiO2-based mold flux during the process of continuous casting, which leads to the deterioration of the mold flux properties and a poor slab quality. Then, the non-reactive CaO-Al2O3-based mold flux was proposed and has been developing for the casting process of high-Al steels, but there are some problems of low consumption and insufficient lubrication that need to be solved. Thus, previous researches on the effect of each component on the properties of CaO-Al2O3-based mold flux were systematically summarized, and the situation of plant trials on CaO-Al2O3-based mold flux was evaluated. The results indicated that the proposed CaO-Al2O3-based mold fluxes could avoid the slag-metal reaction problems;however, the problems of lubri-cation, crystallization and heat transfer issues still exist. Therefore, tremendous works still need to be conducted for the development of new generation of CaO-Al2O3-based mold flux system. The review was performed aiming to provide a technical guidance for designing and optimizing CaO-Al2O3-based mold flux system that meets the demand of the continuous casting process of high-Al steels.
基金supported by the National Key Research and Development Program of China(No.2022YFB3504100)the National Natural Science Foundation of China(No.21972166).
文摘Herein,we review the significant of ordered macroporous(OM)TiO_(2)-based catalysts for boosting pho-tocatalytic CO_(2)reduction.Based on the need to improve the three key factors of photogenerated charge separation eficiency,solar energy utilization and CO_(2)adsorption rate during the conversion of CO_(2)to H_(2)O,we summarized five modification measures:including doping ions into OM TiO_(2),introducing sec-ond semiconductor coupling and noble metal nanoparticles for fabricating multiple Z-scheme heterojunc-tions,constructing hierarchical pore and carbon-loaded OM TiO_(2)materials,which effectively enhance the absorption rate of visible light,the separation rate of electrons-hole pairs and the selection of multiple active sites.The OM structured TiO_(2)-based photocatalysts solve the single or multiple key factors for en-hancing photocatalytic performances during CO_(2)conversion.The catalytic mechanism and pathways of OM structured TiO_(2)-based photocatalysts for CO_(2)reduction are discussed and summarized.It provides new insights on the development of high-efficient catalyst for photocatalytic CO_(2)conversion to solar fu-els.
基金Project(2003 UDBEA00C020) supported by the Collaborative Project of School and Province of Yunnan Province
文摘A new technology was developed to recover multiple valuable elements from the spent Al2O3-based catalyst by X-ray phase analysis and exploratory experiments. The experimental results show that in the condition of roasting temperature of 750℃ and roasting time of 30 min, molar ratio of Na2O to Al2O3 of 1.2, the leaching rates of alumina, vanadium and molybdenum in the spent catalyst are 97.2%, 95.8% and 98.9%, respectively. Vanadium and molybdenum in sodium aluminate solution can be recovered by precipitators A and B, and the precipitation rates of vanadium and molybdenum are 94.8% and 92.6%. Al（OH）3 was prepared from sodium aluminate solution in the carbonation decomposition process, and the purity of Al2O3 is 99.9% after calcination, the recovery of alumina reaches 90.6% in the whole process; the Ni-Co concentrate was leached by sulfuric acid, a nickel recovery of 98.2% and cobalt recovery over 98.5% can be obtained under the experimental condition of 30% H2SO4, 80℃, reaction time 4 h, mass ratio of liquid to solid 8, stirring rate 800r/min.
