A study was undertaken to decrease the sintering temperature and to increase the thermal stability of diamond by adding rare earth elements. The critical factor in the activated sintering is the content of rare earth ...A study was undertaken to decrease the sintering temperature and to increase the thermal stability of diamond by adding rare earth elements. The critical factor in the activated sintering is the content of rare earth element. The results show that adding 0.3% rare earth to the powders makes the composites obtain the properties needed.展开更多
The microstructure and nano-hardness of the pure copper and oxide dispersion-strengthened（ODS） copper alloy subjected to 1.4 Me V Au ions irradiation at room temperature were investigated. After irradiation, disloca...The microstructure and nano-hardness of the pure copper and oxide dispersion-strengthened（ODS） copper alloy subjected to 1.4 Me V Au ions irradiation at room temperature were investigated. After irradiation, dislocation-loops form in both materials, while voids can only be generated in the pure copper. Compared with the irradiated pure copper, larger average diameter and lower number density of irradiation-induced dislocation-loops were detected in the ODS copper alloy, revealing that high-density dislocation and large volume of Al2O3 particles existing in the ODS copper alloy can act as effective sinks for the irradiation-induced defects. It was also detected that irradiation hardening in the ODS copper alloy is lower than that in the pure copper. The microstructure and nano-hardness results reveal that the ODS copper alloy has a better irradiation tolerance than the pure copper. In addition, the average diameter of the Al2O3 particles in the ODS copper alloy decreases after irradiation, because the Al–O chemical bonds are decomposed and the atoms are redistributed in the matrix during the irradiation process. This work reveals that the irradiation tolerance of the copper can be effectively enhanced by adding nano-sized Al2O3 particles into the matrix.展开更多
Shielded Metal Arc Welding (SMAW) in Ductile Irons (DI) is often required by foundries for practical manufacturing reasons. The mechanical properties of the welded structures are strongly dependent on their HAZ’s wid...Shielded Metal Arc Welding (SMAW) in Ductile Irons (DI) is often required by foundries for practical manufacturing reasons. The mechanical properties of the welded structures are strongly dependent on their HAZ’s width. A model based on the behaviour of the ferritic matrix of high-Si DIs in order to make an approach in measuring their HAZ’s width is developed in this study. A series of thermal treatments on 3.35 and 3.75 wt% Si as-cast DIs and spot SMAWs is applied on these materials. The applied SMAWs are done on non-preheated and preheated samples (150℃ - 300℃). For welding we modify the amperage (100 - 140A). The micro-hardness Vickers changes in the ferrite of the as-cast samples and inside the HAZ of the welded ones can be attributed to the existence of residual stresses (RS) in the ferritic matrix and assist in estimating the HAZ’s width.展开更多
Based on the study of existing typical micro-milling tools and the actual demand for micro-milling tools, the P3 design principle and design flow for ultra-hard micro-milling tool were introduced to give basic guidanc...Based on the study of existing typical micro-milling tools and the actual demand for micro-milling tools, the P3 design principle and design flow for ultra-hard micro-milling tool were introduced to give basic guidance for the optimization of micro-milling tools. Then, according to the P3 design flow, the manufacturing process of polycrystalline diamond(PCD) micro-milling tool was proposed, and the PCD micro-milling tool with diameter of 0.5 mm was developed. Finally, the micro-milling test on the slot was carried out to study the milling performance of PCD micromilling tool.展开更多
Inconel 718 superalloy coating was prepared on a martensitic steel substrate by cold gas dynamic spraying （ CGDS ）. Microstructure and micro-hardness of the coating were characterized by means of scanning electronic...Inconel 718 superalloy coating was prepared on a martensitic steel substrate by cold gas dynamic spraying （ CGDS ）. Microstructure and micro-hardness of the coating were characterized by means of scanning electronic microscope （SEM） ,energy dispersive spectrometer （EDS）, and micro-hardness and nano-indentation tests. The results have indicated that the coating＇ s thickness can reach more than 300 um, and there exists a good interfacial cohesion between the coating and the substrate. The quantity and size of the defects at the bottom, middle and top areas increase gradually. There is no significant change to the original microstructure of the Inconel 718 superalloy particle after the process of CGDS ;and an obvious torsional deformation on the particle＇ s profile is produced while little deformation at the center part occurs. The micro-hardness of the coating at the bottom, middle and top areas decreases in turn. Compared with the bottom area, the micro-hardness of the middle and top areas decreases by about 10% and 21%, respectively. The nano-hardness of the coating is much lower than the original particle,which decreases by about 13.5% at the bottom area and 28% at the top area,respectively. The distribution of micro-defects is an important factor to the micro-hardness of the coating.展开更多
Objectives: The effect of ceramics construction (press- able, machinable) and corrosion on flexural strength and micro-hardness was studied. Materials & Methods: Two types of ceramics were tested: IPS e-max Press ...Objectives: The effect of ceramics construction (press- able, machinable) and corrosion on flexural strength and micro-hardness was studied. Materials & Methods: Two types of ceramics were tested: IPS e-max Press and IPS e-max CAD. Forty samples were constructed and divided into 2 groups according to the type of ceramics. Each group was then subdivided into 2 subgroups. Subgroups 1 were not subjected to corrosion while subgroups 2 were subjected to corro-sion test. Finally each subgroup was divided into 2 classes according to the type of test: biaxial flexural strength, micro-hardness. Results: There was a sig-nificant difference between the two tested ceramics as regard weight loss as IPS e-max CAD recorded less weight loss than IPS e-max Press. As regard the flex-ural strength, IPS e-max CAD recorded significant higher strength than IPS e-max Press. Corroded sam- ples recorded significant lower flexural strength than non-corroded samples for the two tested ceramics. As regard the Vickers micro-hardness test, the results showed significant difference between the two tested ceramics. IPS e-max CAD recorded higher mi-cro-hardness values than IPS e-max Press. The results also showed that the corroded samples recorded no significant micro-hardness values than non- corroded samples for the two tested ceramics. Conclusions: IPS e-max CAD recorded less weight loss weight loss after being subjected to corrosion test than IPS e-max Press. The method of fabrication affected the flexural strength µ-hardness of ceramic as machinable ceramic (e-max CAD) recorded significant higher data than pressable ceramic (e-mas Press). Corrosion decreased the flexural strength of both tested ceramics but had no effect on micro- hardness.展开更多
The present study focuses on the relationship of hardness with grain size for commercially pure titanium （CpTi） and ultra fine grained titanium （UFG-Ti） produced by equal channel angular process （ECAP） of Cp-Ti...The present study focuses on the relationship of hardness with grain size for commercially pure titanium （CpTi） and ultra fine grained titanium （UFG-Ti） produced by equal channel angular process （ECAP） of Cp-Ti）.Vickers and Knoop indentations of UFG-Ti at different loads was ～2.5 times harder than those of Cp-Ti.Xray diffraction （XRD） analysis showed peak broadening in UFG-Ti due to reduced grain size and micro-lattice strains.Scanning electron microscopy （SEM） revealed that ECAP had reduced the grain size of Cp-Ti by ～10 times.Weibull statistics showed UFG-Ti with lower dispersion in hardness values compare to Cp-Ti indicating a more uniform microstructure.展开更多
The oxide dispersion strengthened copper alloys are attractive due to their excellent combination of thermal and electrical conductivities,high-temperature strength and microstructure stability.To date,the state-of-ar...The oxide dispersion strengthened copper alloys are attractive due to their excellent combination of thermal and electrical conductivities,high-temperature strength and microstructure stability.To date,the state-of-art to fabrication of them was the internal oxidation （IO） process.In this paper,alumina dispersion strengthened copper （ADSC） powders of nominal composition of Cu-2.5 vol%Al2O3 were produced by reaction milling （RM） process which was an in-situ gas-solid reaction process.The bulk ADSC alloys for electrical and mechanical properties investigation were obtained by sintering and thereafter hot extrusion.After the hot consolidation processes,the fully densified powder compacts can be obtained.The single γ-Al2O3 phase and profile broaden effects are evident in accordance with the results of X-ray diffraction （XRD）;the HRB hardness of the ADSC can be as high as 95;the outcomes should be attributed to the pinning effect of nano γ-Al2O3 on dislocations and grain boundaries in the copper matrix.The electrical conductivity of the ADSC alloy is 55%IACS （International Annealing Copper Standard）.The room temperature hardness of the hot consolidated material was approximately maintained after annealing for 1 h at 900 ℃ in hydrogen atmosphere.In terms of the above merits,the RM process to fabricating ADSC alloys is a promising method to improve heat resistance,hardness,electrical conductivity and wear resistance properties etc.展开更多
The electroless Ni-P-SiC composite coatings were prepared and the influence of vacuum heat treatment on its structure and properties was analyzed. The Ni-P-SiC composite coatings were characterized by morphology,struc...The electroless Ni-P-SiC composite coatings were prepared and the influence of vacuum heat treatment on its structure and properties was analyzed. The Ni-P-SiC composite coatings were characterized by morphology,structure and micro-hardness. The morphology and structure of the Ni-P-SiC composite coatings were studied by scanning electron microscopy(SEM) and X-ray diffractometry(XRD),respectively. A great deal of particles incorporation and uniform distribution were found in Ni-P-SiC composite coatings. XRD results show a broad peak of nickel and low intensity SiC peaks present on as-deposited condition. Micro-hardness of as-deposited Ni-P-SiC composite coatings is improved greatly,and the best micro-hardness is obtained after heat treatment in a high vacuum at 400 ℃ .展开更多
The hot hardness behavior of Zr52.5Al10Ni10Cu15Be12.5 bulk metallic glass is studied from ambient temperature to the temperature over Tx （the onset crystallization temperature） using a hot macro-hardness tester and ...The hot hardness behavior of Zr52.5Al10Ni10Cu15Be12.5 bulk metallic glass is studied from ambient temperature to the temperature over Tx （the onset crystallization temperature） using a hot macro-hardness tester and scanning electron microscopy （SEM）. The results show that the hot hardness behavior of Zr52.5Al10Ni10Cu15Be12.5 bulk metallic glass can be classified into 4 zones： the glassy zone in which the hardness almost linearly decreases with the increase of temperature, the viscoelastic zone in which the hardness is nearly unchanged, the viscous flow zone in which the hardness quickly tends towards near zero with temperature, and the crystallization zone in which the hardness sharply increases. The high temperature deformation behavior and the easy processable deformation region for bulk metallic glasses are also discussed on the basis of the hot marco-hardness.展开更多
Mathematical models between surfacing welding properties of C, Cr, Mo, V, W alloy system and encode factors of alloy additives are established by test methods of advanced trial optimizing technology and computer assis...Mathematical models between surfacing welding properties of C, Cr, Mo, V, W alloy system and encode factors of alloy additives are established by test methods of advanced trial optimizing technology and computer assistant design (CAD). They help to draw unitary functions and binary isoclines diagrams through which the influence of encode factorial linearity, nonlinear effect and factors interaction of alloy additives on the performances of surfacing welding can be analyzed directly and quantitatively. Meanwhile, the performances of deposited metal can also be predicted according to the content of alloy additives.展开更多
In this paper, single machine scheduling problems with variable processing time is discussed according to published instances of management engineering. Processing time of a job is the product of a “coefficient' ...In this paper, single machine scheduling problems with variable processing time is discussed according to published instances of management engineering. Processing time of a job is the product of a “coefficient' of the job on position i and a “normal' processing time of the job. The criteria considered is to minimize scheduled length of all jobs. A lemma is proposed and proved. In no deadline constrained condition, the problem belongs to polynomial time algorithm. It is proved by using 3 partition that if the problem is deadline constrained, its complexity is strong NP hard. Finally, a conjuncture is proposed that is to be proved.展开更多
文摘A study was undertaken to decrease the sintering temperature and to increase the thermal stability of diamond by adding rare earth elements. The critical factor in the activated sintering is the content of rare earth element. The results show that adding 0.3% rare earth to the powders makes the composites obtain the properties needed.
基金financially supported by the National Natural Science Foundation of China (Nos. 11175014, 50971030)the National Basic Research Program of China (No. 11163110)the National Magnetic Confinement Fusion Program (No. 2011GB108002)
文摘The microstructure and nano-hardness of the pure copper and oxide dispersion-strengthened（ODS） copper alloy subjected to 1.4 Me V Au ions irradiation at room temperature were investigated. After irradiation, dislocation-loops form in both materials, while voids can only be generated in the pure copper. Compared with the irradiated pure copper, larger average diameter and lower number density of irradiation-induced dislocation-loops were detected in the ODS copper alloy, revealing that high-density dislocation and large volume of Al2O3 particles existing in the ODS copper alloy can act as effective sinks for the irradiation-induced defects. It was also detected that irradiation hardening in the ODS copper alloy is lower than that in the pure copper. The microstructure and nano-hardness results reveal that the ODS copper alloy has a better irradiation tolerance than the pure copper. In addition, the average diameter of the Al2O3 particles in the ODS copper alloy decreases after irradiation, because the Al–O chemical bonds are decomposed and the atoms are redistributed in the matrix during the irradiation process. This work reveals that the irradiation tolerance of the copper can be effectively enhanced by adding nano-sized Al2O3 particles into the matrix.
文摘Shielded Metal Arc Welding (SMAW) in Ductile Irons (DI) is often required by foundries for practical manufacturing reasons. The mechanical properties of the welded structures are strongly dependent on their HAZ’s width. A model based on the behaviour of the ferritic matrix of high-Si DIs in order to make an approach in measuring their HAZ’s width is developed in this study. A series of thermal treatments on 3.35 and 3.75 wt% Si as-cast DIs and spot SMAWs is applied on these materials. The applied SMAWs are done on non-preheated and preheated samples (150℃ - 300℃). For welding we modify the amperage (100 - 140A). The micro-hardness Vickers changes in the ferrite of the as-cast samples and inside the HAZ of the welded ones can be attributed to the existence of residual stresses (RS) in the ferritic matrix and assist in estimating the HAZ’s width.
基金Supported by the National Natural Science Foundation of China(No.50935003)Science and Technology Support Project of Jiangsu Province,China(No.BE2012172)
文摘Based on the study of existing typical micro-milling tools and the actual demand for micro-milling tools, the P3 design principle and design flow for ultra-hard micro-milling tool were introduced to give basic guidance for the optimization of micro-milling tools. Then, according to the P3 design flow, the manufacturing process of polycrystalline diamond(PCD) micro-milling tool was proposed, and the PCD micro-milling tool with diameter of 0.5 mm was developed. Finally, the micro-milling test on the slot was carried out to study the milling performance of PCD micromilling tool.
文摘Inconel 718 superalloy coating was prepared on a martensitic steel substrate by cold gas dynamic spraying （ CGDS ）. Microstructure and micro-hardness of the coating were characterized by means of scanning electronic microscope （SEM） ,energy dispersive spectrometer （EDS）, and micro-hardness and nano-indentation tests. The results have indicated that the coating＇ s thickness can reach more than 300 um, and there exists a good interfacial cohesion between the coating and the substrate. The quantity and size of the defects at the bottom, middle and top areas increase gradually. There is no significant change to the original microstructure of the Inconel 718 superalloy particle after the process of CGDS ;and an obvious torsional deformation on the particle＇ s profile is produced while little deformation at the center part occurs. The micro-hardness of the coating at the bottom, middle and top areas decreases in turn. Compared with the bottom area, the micro-hardness of the middle and top areas decreases by about 10% and 21%, respectively. The nano-hardness of the coating is much lower than the original particle,which decreases by about 13.5% at the bottom area and 28% at the top area,respectively. The distribution of micro-defects is an important factor to the micro-hardness of the coating.
文摘Objectives: The effect of ceramics construction (press- able, machinable) and corrosion on flexural strength and micro-hardness was studied. Materials & Methods: Two types of ceramics were tested: IPS e-max Press and IPS e-max CAD. Forty samples were constructed and divided into 2 groups according to the type of ceramics. Each group was then subdivided into 2 subgroups. Subgroups 1 were not subjected to corrosion while subgroups 2 were subjected to corro-sion test. Finally each subgroup was divided into 2 classes according to the type of test: biaxial flexural strength, micro-hardness. Results: There was a sig-nificant difference between the two tested ceramics as regard weight loss as IPS e-max CAD recorded less weight loss than IPS e-max Press. As regard the flex-ural strength, IPS e-max CAD recorded significant higher strength than IPS e-max Press. Corroded sam- ples recorded significant lower flexural strength than non-corroded samples for the two tested ceramics. As regard the Vickers micro-hardness test, the results showed significant difference between the two tested ceramics. IPS e-max CAD recorded higher mi-cro-hardness values than IPS e-max Press. The results also showed that the corroded samples recorded no significant micro-hardness values than non- corroded samples for the two tested ceramics. Conclusions: IPS e-max CAD recorded less weight loss weight loss after being subjected to corrosion test than IPS e-max Press. The method of fabrication affected the flexural strength µ-hardness of ceramic as machinable ceramic (e-max CAD) recorded significant higher data than pressable ceramic (e-mas Press). Corrosion decreased the flexural strength of both tested ceramics but had no effect on micro- hardness.
文摘The present study focuses on the relationship of hardness with grain size for commercially pure titanium （CpTi） and ultra fine grained titanium （UFG-Ti） produced by equal channel angular process （ECAP） of Cp-Ti）.Vickers and Knoop indentations of UFG-Ti at different loads was ～2.5 times harder than those of Cp-Ti.Xray diffraction （XRD） analysis showed peak broadening in UFG-Ti due to reduced grain size and micro-lattice strains.Scanning electron microscopy （SEM） revealed that ECAP had reduced the grain size of Cp-Ti by ～10 times.Weibull statistics showed UFG-Ti with lower dispersion in hardness values compare to Cp-Ti indicating a more uniform microstructure.
文摘The oxide dispersion strengthened copper alloys are attractive due to their excellent combination of thermal and electrical conductivities,high-temperature strength and microstructure stability.To date,the state-of-art to fabrication of them was the internal oxidation （IO） process.In this paper,alumina dispersion strengthened copper （ADSC） powders of nominal composition of Cu-2.5 vol%Al2O3 were produced by reaction milling （RM） process which was an in-situ gas-solid reaction process.The bulk ADSC alloys for electrical and mechanical properties investigation were obtained by sintering and thereafter hot extrusion.After the hot consolidation processes,the fully densified powder compacts can be obtained.The single γ-Al2O3 phase and profile broaden effects are evident in accordance with the results of X-ray diffraction （XRD）;the HRB hardness of the ADSC can be as high as 95;the outcomes should be attributed to the pinning effect of nano γ-Al2O3 on dislocations and grain boundaries in the copper matrix.The electrical conductivity of the ADSC alloy is 55%IACS （International Annealing Copper Standard）.The room temperature hardness of the hot consolidated material was approximately maintained after annealing for 1 h at 900 ℃ in hydrogen atmosphere.In terms of the above merits,the RM process to fabricating ADSC alloys is a promising method to improve heat resistance,hardness,electrical conductivity and wear resistance properties etc.
基金Projects(05B008) supported by Scientific Research Fund of Hunan Provincial Education Departmentproject(104014) supported by Fok Ying Tong Education Foundation of Ministry of Education
文摘The electroless Ni-P-SiC composite coatings were prepared and the influence of vacuum heat treatment on its structure and properties was analyzed. The Ni-P-SiC composite coatings were characterized by morphology,structure and micro-hardness. The morphology and structure of the Ni-P-SiC composite coatings were studied by scanning electron microscopy(SEM) and X-ray diffractometry(XRD),respectively. A great deal of particles incorporation and uniform distribution were found in Ni-P-SiC composite coatings. XRD results show a broad peak of nickel and low intensity SiC peaks present on as-deposited condition. Micro-hardness of as-deposited Ni-P-SiC composite coatings is improved greatly,and the best micro-hardness is obtained after heat treatment in a high vacuum at 400 ℃ .
基金Project supported by the National Natural Science Foundation of China （Grant No.50201009）
文摘The hot hardness behavior of Zr52.5Al10Ni10Cu15Be12.5 bulk metallic glass is studied from ambient temperature to the temperature over Tx （the onset crystallization temperature） using a hot macro-hardness tester and scanning electron microscopy （SEM）. The results show that the hot hardness behavior of Zr52.5Al10Ni10Cu15Be12.5 bulk metallic glass can be classified into 4 zones： the glassy zone in which the hardness almost linearly decreases with the increase of temperature, the viscoelastic zone in which the hardness is nearly unchanged, the viscous flow zone in which the hardness quickly tends towards near zero with temperature, and the crystallization zone in which the hardness sharply increases. The high temperature deformation behavior and the easy processable deformation region for bulk metallic glasses are also discussed on the basis of the hot marco-hardness.
文摘Mathematical models between surfacing welding properties of C, Cr, Mo, V, W alloy system and encode factors of alloy additives are established by test methods of advanced trial optimizing technology and computer assistant design (CAD). They help to draw unitary functions and binary isoclines diagrams through which the influence of encode factorial linearity, nonlinear effect and factors interaction of alloy additives on the performances of surfacing welding can be analyzed directly and quantitatively. Meanwhile, the performances of deposited metal can also be predicted according to the content of alloy additives.
文摘In this paper, single machine scheduling problems with variable processing time is discussed according to published instances of management engineering. Processing time of a job is the product of a “coefficient' of the job on position i and a “normal' processing time of the job. The criteria considered is to minimize scheduled length of all jobs. A lemma is proposed and proved. In no deadline constrained condition, the problem belongs to polynomial time algorithm. It is proved by using 3 partition that if the problem is deadline constrained, its complexity is strong NP hard. Finally, a conjuncture is proposed that is to be proved.
