Several protocols and schemes have been proposed to reduce energy consumption in Wireless Sensor Net-works (WSNs). In this paper we employ farcoopt, a cross layer design approach with the concept of coop-eration among...Several protocols and schemes have been proposed to reduce energy consumption in Wireless Sensor Net-works (WSNs). In this paper we employ farcoopt, a cross layer design approach with the concept of coop-eration among the nodes with best farthest neighbor scheme to increase the Quality of Service (QoS), reduce energy consumption, increases performance and end-to-end throughput. We present cooperative transmission to connect previously disconnect parts of a network thus overcoming the separation problem of multi-hop network. We show that this approach improves connectivity over 50% compared to multi-hop approaches and reduces the number of nodes necessary to provide full coverage of an area up to 35%. Simulation results show that on increase of data rates i.e. packet the network life time increases in farcoopt as compared to tra-ditional multi hop approach. The result of this analysis is presented in this work.展开更多
Wireless Mesh Network is presented as an appealing solution for bridging the digital divide between developed and under-developed regions. But the planning and deployment of these networks are not just a technical mat...Wireless Mesh Network is presented as an appealing solution for bridging the digital divide between developed and under-developed regions. But the planning and deployment of these networks are not just a technical matter, since the success depends on many other factors tied to the related region. Although we observe some deployments, to ensure usefulness and sustainability, there is still a need of concrete design process model and proper network planning approach for rural regions, especially in Sub-Saharan Africa. This paper presents a design methodology to provide network connectivity from a landline node in a rural region at very low cost. We propose a methodology composed of ten steps, starting by a deep analysis of the region in order to identify relevant constraints and useful applications to sustain local activities and communication. Approach for planning the physical architecture of the network is based on an indoor-outdoor deployment for reducing the overall cost of the network.展开更多
A proactive routing protocol CL-OLSR （cross-layer based optimized link state routing） by using a brand-new routing metric CLM （cross-layer metric） is proposed. CL-OLSR takes into account four link quality impact f...A proactive routing protocol CL-OLSR （cross-layer based optimized link state routing） by using a brand-new routing metric CLM （cross-layer metric） is proposed. CL-OLSR takes into account four link quality impact factors in route calculation through the cross-layer operation mechanism： the node available bandwidth, the node load, the link delivery rate, and the link interference, and thus the effect of route selection is optimized greatly. The simulation results show that the proposed CL-OLSR protocol can not only improve the network throughput to a large extent, but also reduce the end-to-end delay, while achieving load balance route results.展开更多
Designing low power sensor networks has been the general goal of design engineers, scientist and end users. It is desired to have a wireless sensor network (WSN) that will run on little power (if possible, none at all...Designing low power sensor networks has been the general goal of design engineers, scientist and end users. It is desired to have a wireless sensor network (WSN) that will run on little power (if possible, none at all) thereby saving cost, and the inconveniences of having to replace batteries in some difficult to access areas of usage. Previous researches on WSN energy models have focused less on the aggregate transceiver energy consumption models as compared to studies on other components of the node, hence a large portion of energy in a WSN still get depleted through data transmission. By studying the energy consumption map of the transceiver of a WSN node in different states and within state transitions, we propose in this paper the energy consumption model of the transceiver unit of a typical sensor node and the transceiver design parameters that significantly influences this energy consumption. The contribution of this paper is an innovative energy consumption model based on simple finite automata which reveals the relationship between the aggregate energy consumption and important power parameters that characterize the energy consumption map of the transceiver in a WSN;an ideal tool to design low power WSN.展开更多
We investigate the problem of how to minimize the energy consumption in multi-hop Wireless Sensor Network (WSN),under the constraint of end-to-end reliability Quality of Seervice (QoS) requirement.Based on the investi...We investigate the problem of how to minimize the energy consumption in multi-hop Wireless Sensor Network (WSN),under the constraint of end-to-end reliability Quality of Seervice (QoS) requirement.Based on the investigation,we jointly consider the routing,relay selection and power allocation algorithm,and present a novel distributed cross-layer strategy using opportunistic relaying scheme for cooperative communication.The results show that under the same QoS requirement,the proposed cross-layer strategy performs better than other cross-layer cooperative communication algorithms in energy efficiency.We also investigated the impact of several parameters on the energy efficiency of the cooperative communication in WSNs,thus can be used to provide guidelines to decide when and how to apply cooperation for a given setup.展开更多
This paper presents a wireless sensor network (WSN) access control algorithm designed to minimize WSN node energy consumption. Based on slotted ALOHA protocol, this algorithm incorporates the power control of physical...This paper presents a wireless sensor network (WSN) access control algorithm designed to minimize WSN node energy consumption. Based on slotted ALOHA protocol, this algorithm incorporates the power control of physical layer, the transmitting probability of medium access control (MAC) layer, and the automatic repeat request (ARQ) of link layer. In this algorithm, a cross-layer optimization is preformed to minimizing the energy consuming per bit. Through theory deducing, the transmitting probability and transmitting power level is determined, and the relationship between energy consuming per bit and throughput per node is provided. Analytical results show that the cross-layer algorithm results in a significant energy savings relative to layered design subject to the same throughput per node, and the energy saving is extraordinary in the low throughput region.展开更多
Wireless mesh networks (WMNs) are new kind of networking technology which facilitate the extension of wireless local area networks into wide areas and have emerged as a key technology for next-generation wireless netw...Wireless mesh networks (WMNs) are new kind of networking technology which facilitate the extension of wireless local area networks into wide areas and have emerged as a key technology for next-generation wireless networking.Due to the advantages of WMNs over other wireless networks,they are now a promising approach for future network access.Typical applications range from home broadband Internet access and community networking to wireless metropolitan area networks.Meanwhile,the considerable efforts in academic range from network architecture,network capacity,layered communication protocols,security,cross-layer design,etc.Still many technical challenges exist in designing affordable,reliable,and sustainable WMNs infrastructures.In order to provide a better understanding of these challenges,this paper presents a detailed investigation of current technologies for WMNs,and it will help to guide and refocus future works in this area.展开更多
In this paper, aiming to improve the quality of multimedia transmission while satisfying the quality of service (QoS) requirements, we propose an optimal subcarrier allocation by jointly considering the video coding r...In this paper, aiming to improve the quality of multimedia transmission while satisfying the quality of service (QoS) requirements, we propose an optimal subcarrier allocation by jointly considering the video coding rate and the available power resource. We jointly analyses the effects on the performance of multimedia transmission from video coding rate at the application layer as well as the power control at the physical layer. This proposed joint power and subcarrier allocation algorithm in MIMO OFDM systems enables us both to overcome the challenge of full CSI (channel state information) with RD (the rate-distortion) to make minimum of the distortion of each users under delay and power constraints. Simulation results show that the proposed optimal subcarrier allocation algorithm improves the multimedia transmission quality considerably through the comparison with the resource allocation algorithms only use a single layer of information.展开更多
This paper describes a novel energy-aware multi-hop cluster-based fault-tolerant load balancing hierarchical routing protocol for a self-organizing wireless sensor network (WSN), which takes into account the broadcast...This paper describes a novel energy-aware multi-hop cluster-based fault-tolerant load balancing hierarchical routing protocol for a self-organizing wireless sensor network (WSN), which takes into account the broadcast nature of radio. The main idea is using hierarchical fuzzy soft clusters enabling non-exclusive overlapping clusters, thus allowing partial multiple membership of a node to more than one cluster, whereby for each cluster the clusterhead (CH) takes in charge intra-cluster issues of aggregating the information from nodes members, and then collaborate and coordinate with its related overlapping area heads (OAHs), which are elected heuristically to ensure inter-clusters communication. This communication is implemented using an extended version of time-division multiple access (TDMA) allowing the allocation of several slots for a given node, and alternating the role of the clusterhead and its associated overlapping area heads. Each cluster head relays information to overlapping area heads which in turn each relays it to other associated cluster heads in related clusters, thus the information propagates gradually until it reaches the sink in a multi-hop fashion.展开更多
The main research objective in wireless sensor networks (WSN) domain is to develop algorithms and protocols to ensure minimal energy consumption with maximum network lifetime. In this paper, we propose a novel design ...The main research objective in wireless sensor networks (WSN) domain is to develop algorithms and protocols to ensure minimal energy consumption with maximum network lifetime. In this paper, we propose a novel design for energy harvesting sensor node and cross-layered MAC protocol using three adjacent layers (Physical, MAC and Network) to economize energy for WSN. The basic idea behind our protocol is to re-energize the neighboring nodes using the radio frequency (RF) energy transmitted by the active nodes. This can be achieved by designing new energy harvesting sensor node and redesigning the MAC protocol. The results show that the proposed cross layer CL_EHSN improves the life time of the WSN by 40%.展开更多
Clustering or connected dominating set (CDS) both approaches can establish a virtual backbone (VB) in wireless sensor networks (WSNs) or wireless mesh networks (WMNs). Each cluster consisting of a cluster head (CH) an...Clustering or connected dominating set (CDS) both approaches can establish a virtual backbone (VB) in wireless sensor networks (WSNs) or wireless mesh networks (WMNs). Each cluster consisting of a cluster head (CH) and its neighboring nodes can form a dominating set. After some bridging nodes were selected, cluster heads (CHs) connected through these bridging nodes naturally formed a CDS. Although CDS provides obvious backbone architecture, however, the number of cluster heads and bridging nodes may be too large, this may cause the loss of advantages of virtual backbone. When we effectively reduce their numbers, more effectively WCDS (Weakly Connected Dominating Set) can be fining out. Some essential topics on constructing WCDS-based VB in WSN/WMN are discussed in this paper. From the point of view of three different protocol layers, including network (NWK) layer, MAC layer, and physical (PHY) layer, we explore their cross-layer research topics and design algorithms. For NWK layer, area-based WCDS algorithms and routing strategies including via VB and not via VB are discussed. For MAC layer, a WCDS-based energy-efficient MAC protocol is presented. For PHY layer, battery-aware alternative VB selections and sensor nodes with different transmission ranges are addressed.展开更多
Wireless Multimedia Sensor Networks (WMSNs), is a network of sensors, which are limited in terms of memory, computing, bandwidth, and battery lifetime. Multimedia transmission over WSN requires certain QoS guarantees ...Wireless Multimedia Sensor Networks (WMSNs), is a network of sensors, which are limited in terms of memory, computing, bandwidth, and battery lifetime. Multimedia transmission over WSN requires certain QoS guarantees such as huge amount of bandwidth, strict delay and lower loss ratio that makes transmitting multimedia is a complicated task. However, adopting cross-layer approach in WMSNs improves quality of service of WSN under different environmental conditions. In this work, an energy efficient and QoS aware framework for transmitting multimedia content over WSN (EQWSN) is presented, where packet, queue and path scheduling were introduced. It adapts the application layer parameter of video encoder to current wireless channel state, and drops less important packets in case of network congestion according to packet type. Finally, the path scheduling differentiates packets types/priority and route them through different paths with different QoS considering network lifetime. Simulation results show that the new scheme EQWSN transmits video quality with QoS guarantees in addition to prolonging network lifetime.展开更多
Advance development of wireless technologies and micro-sensor systems have enabled Wireless Sensor Network (WSN) to emerge as a leading solution in many crucial sensor-based applications. WSN deploys numerous resource...Advance development of wireless technologies and micro-sensor systems have enabled Wireless Sensor Network (WSN) to emerge as a leading solution in many crucial sensor-based applications. WSN deploys numerous resource-constrained sensor nodes which have limited power supply, memory and computation capability in a harsh environment. Inefficient routing strategy results in degraded network performance in terms of reliability, latency and energy efficiency. In this paper, a cross-layer design, Contention-based MAC and Routing protocol is proposed, termed Contention/SNIR-Based Forwarding (CSBF) protocol. CSBF utilizes the geographical information of sensor nodes to effectively guide the routing direction towards destination node, thereby enhancing reliability. Furthermore, Signal-to-Noise-plus-Interference Ratio (SNIR) metric is used as a routing parameter to guarantee high quality link for data transmission. A Contention-Winner Relay scheme is utilized to reduce the delays caused by the contention procedure. Energy efficiency is also improved by introducing sleep mode technique in CSBF. The simulation work is carried out via OMNeT++ network simulator. The performance of CSBF is compared with other existing routing protocols such as AODV and DSDV in terms of packet delivery ratio (PDR), average end-to-end (ETE) delay and energy consumption per packet. Simulation results highlight that CSBF outperforms AODV and DSDV protocols in respect of PDR and energy efficiency. CSBF also has the most consistent overall network performance.展开更多
With the development of CMOS and MEMS technologies, the implementation of a large number of wireless distributed micro-sensors that can be easily and rapidly deployed to form highly redundant, self-configuring, and ad...With the development of CMOS and MEMS technologies, the implementation of a large number of wireless distributed micro-sensors that can be easily and rapidly deployed to form highly redundant, self-configuring, and ad hoc sensor networks. To facilitate ease of deployment, these sensors operate on battery for extended periods of time. A particular challenge in maintaining extended battery lifetime lies in achieving communications with low power. For better understanding of the design tradeoffs of wireless sensor network （WSN）, a more accurate energy model for wireless sensor node is proposed, and an optimal design method of energy efficient wireless sensor node is described as well. Different from power models ever shown which assume the power cost of each component in WSN node is constant, the new one takes into account the energy dissipation of circuits in practical physical layer. It shows that there are some parameters, such as data rate, carrier frequency, bandwidth, Tsw, etc, which have a significant effect on the WSN node energy consumption per useful bit （EPUB）. For a given quality specification, how energy consumption can be reduced by adjusting one or more of these parameters is shown.展开更多
This work is about the development of a super low noise amplifier with minimum power consumption and high gain for several wireless applications.The amplifier operates at frequency bands of 0.9-2.4 GHz and can be used...This work is about the development of a super low noise amplifier with minimum power consumption and high gain for several wireless applications.The amplifier operates at frequency bands of 0.9-2.4 GHz and can be used in many applications like Wireless local area network(WLAN),WiFi,Bluetooth,ZigBee and Global System for mobile communications(GSM).This new design can be employed for the IEEE 802.15.4 standard in industrial,scientific and medical(ISM) Band.The enhancement mode pseudomorphic high electron mobility transistor PHEMT is used here due to its high linearity,better performance and less noisy operation.The common source inductive degeneration method is employed here to enhance the gain of amplifier.The amplifier produces a gain of more than 17 dB and noise figure of about 0.5 dB.The lower values of S11 and S22 reflect the accuracy of impedance matching network placed at the input and output sides of amplifier.Agilent Advance Design System(ADS) is used for the design and simulation purpose.Further the layout of design is developed on the FR4 substrate.展开更多
Complex and distributed systems are more and more associated with the application of WSN (Wireless Sensor Network) technology. The design of such applications presents important challenges and requires the assistance ...Complex and distributed systems are more and more associated with the application of WSN (Wireless Sensor Network) technology. The design of such applications presents important challenges and requires the assistance of several methodologies and tools. Multi-Agent systems (MAS) have been identified as one of the most suitable technologies to contribute to this domain due to their appropriateness for modeling distributed and autonomous complex systems. This work aims to contribute in the help of the design of WSN applications. The proposed architecture exploits the advantages of MAS for modeling WSN services, network topologies and sensor device architectures.展开更多
Communication over wireless links identifies significant challenges for routing protocols operating. This paper proposes a Cross-layer design based Multipath Routing Protocol (CMRP) for mobile ad hoc networks, by mean...Communication over wireless links identifies significant challenges for routing protocols operating. This paper proposes a Cross-layer design based Multipath Routing Protocol (CMRP) for mobile ad hoc networks, by means of the node energy signal from the physical layer. The purpose is to optimize routing decision and path quality. The nodes’ mobility behavior is predicted using a notion of “Signal Fading Degree, SFD”. Especially, in combination of the IEEE 802.11e standard at the MAC layer, we determine that the IEEE 802.11e makes a significant contribution to performance improvement of CMRP. Performance evaluation of AODV in legacy 802.11 and CMRP in IEEE 802.11e shows that, as a function of speed of node mobility, a tremendous reduction achieved, in metrics such as the average end-to-end delay, route overhead, route discovery frequency, normalized routing load - almost more than 80%, 40%, 40%, and 40%. In the case of varying number of sessions, the reduction for route discovery frequency and normalized routing load are up to 70% and 80%.展开更多
文摘Several protocols and schemes have been proposed to reduce energy consumption in Wireless Sensor Net-works (WSNs). In this paper we employ farcoopt, a cross layer design approach with the concept of coop-eration among the nodes with best farthest neighbor scheme to increase the Quality of Service (QoS), reduce energy consumption, increases performance and end-to-end throughput. We present cooperative transmission to connect previously disconnect parts of a network thus overcoming the separation problem of multi-hop network. We show that this approach improves connectivity over 50% compared to multi-hop approaches and reduces the number of nodes necessary to provide full coverage of an area up to 35%. Simulation results show that on increase of data rates i.e. packet the network life time increases in farcoopt as compared to tra-ditional multi hop approach. The result of this analysis is presented in this work.
文摘Wireless Mesh Network is presented as an appealing solution for bridging the digital divide between developed and under-developed regions. But the planning and deployment of these networks are not just a technical matter, since the success depends on many other factors tied to the related region. Although we observe some deployments, to ensure usefulness and sustainability, there is still a need of concrete design process model and proper network planning approach for rural regions, especially in Sub-Saharan Africa. This paper presents a design methodology to provide network connectivity from a landline node in a rural region at very low cost. We propose a methodology composed of ten steps, starting by a deep analysis of the region in order to identify relevant constraints and useful applications to sustain local activities and communication. Approach for planning the physical architecture of the network is based on an indoor-outdoor deployment for reducing the overall cost of the network.
基金supported by the Fundamental Research Funds for the Central Universities under Grant No.ZYGX2009j006Foundation of Science & Technology Department of Sichuan Province under Grant No.2011GZ0192
文摘A proactive routing protocol CL-OLSR （cross-layer based optimized link state routing） by using a brand-new routing metric CLM （cross-layer metric） is proposed. CL-OLSR takes into account four link quality impact factors in route calculation through the cross-layer operation mechanism： the node available bandwidth, the node load, the link delivery rate, and the link interference, and thus the effect of route selection is optimized greatly. The simulation results show that the proposed CL-OLSR protocol can not only improve the network throughput to a large extent, but also reduce the end-to-end delay, while achieving load balance route results.
文摘Designing low power sensor networks has been the general goal of design engineers, scientist and end users. It is desired to have a wireless sensor network (WSN) that will run on little power (if possible, none at all) thereby saving cost, and the inconveniences of having to replace batteries in some difficult to access areas of usage. Previous researches on WSN energy models have focused less on the aggregate transceiver energy consumption models as compared to studies on other components of the node, hence a large portion of energy in a WSN still get depleted through data transmission. By studying the energy consumption map of the transceiver of a WSN node in different states and within state transitions, we propose in this paper the energy consumption model of the transceiver unit of a typical sensor node and the transceiver design parameters that significantly influences this energy consumption. The contribution of this paper is an innovative energy consumption model based on simple finite automata which reveals the relationship between the aggregate energy consumption and important power parameters that characterize the energy consumption map of the transceiver in a WSN;an ideal tool to design low power WSN.
基金Supported by the 100 Top-Talents Program of Chinese Academic of Sciences (No. 99M2008M02)
文摘We investigate the problem of how to minimize the energy consumption in multi-hop Wireless Sensor Network (WSN),under the constraint of end-to-end reliability Quality of Seervice (QoS) requirement.Based on the investigation,we jointly consider the routing,relay selection and power allocation algorithm,and present a novel distributed cross-layer strategy using opportunistic relaying scheme for cooperative communication.The results show that under the same QoS requirement,the proposed cross-layer strategy performs better than other cross-layer cooperative communication algorithms in energy efficiency.We also investigated the impact of several parameters on the energy efficiency of the cooperative communication in WSNs,thus can be used to provide guidelines to decide when and how to apply cooperation for a given setup.
文摘This paper presents a wireless sensor network (WSN) access control algorithm designed to minimize WSN node energy consumption. Based on slotted ALOHA protocol, this algorithm incorporates the power control of physical layer, the transmitting probability of medium access control (MAC) layer, and the automatic repeat request (ARQ) of link layer. In this algorithm, a cross-layer optimization is preformed to minimizing the energy consuming per bit. Through theory deducing, the transmitting probability and transmitting power level is determined, and the relationship between energy consuming per bit and throughput per node is provided. Analytical results show that the cross-layer algorithm results in a significant energy savings relative to layered design subject to the same throughput per node, and the energy saving is extraordinary in the low throughput region.
基金supported in part by the National High Technology Research and Development Program of China (863 Program) (No. 2006AA01Z232,2009AA01Z212, 2009AA01Z202)Key Science and Technology Supporting Plan Item of Jiangsu Province(No. BE2008134)Special Fund of Trans-formation of Scientific and Technological Achievements of Jiangsu Province(No. BA2007012)
文摘Wireless mesh networks (WMNs) are new kind of networking technology which facilitate the extension of wireless local area networks into wide areas and have emerged as a key technology for next-generation wireless networking.Due to the advantages of WMNs over other wireless networks,they are now a promising approach for future network access.Typical applications range from home broadband Internet access and community networking to wireless metropolitan area networks.Meanwhile,the considerable efforts in academic range from network architecture,network capacity,layered communication protocols,security,cross-layer design,etc.Still many technical challenges exist in designing affordable,reliable,and sustainable WMNs infrastructures.In order to provide a better understanding of these challenges,this paper presents a detailed investigation of current technologies for WMNs,and it will help to guide and refocus future works in this area.
文摘In this paper, aiming to improve the quality of multimedia transmission while satisfying the quality of service (QoS) requirements, we propose an optimal subcarrier allocation by jointly considering the video coding rate and the available power resource. We jointly analyses the effects on the performance of multimedia transmission from video coding rate at the application layer as well as the power control at the physical layer. This proposed joint power and subcarrier allocation algorithm in MIMO OFDM systems enables us both to overcome the challenge of full CSI (channel state information) with RD (the rate-distortion) to make minimum of the distortion of each users under delay and power constraints. Simulation results show that the proposed optimal subcarrier allocation algorithm improves the multimedia transmission quality considerably through the comparison with the resource allocation algorithms only use a single layer of information.
文摘This paper describes a novel energy-aware multi-hop cluster-based fault-tolerant load balancing hierarchical routing protocol for a self-organizing wireless sensor network (WSN), which takes into account the broadcast nature of radio. The main idea is using hierarchical fuzzy soft clusters enabling non-exclusive overlapping clusters, thus allowing partial multiple membership of a node to more than one cluster, whereby for each cluster the clusterhead (CH) takes in charge intra-cluster issues of aggregating the information from nodes members, and then collaborate and coordinate with its related overlapping area heads (OAHs), which are elected heuristically to ensure inter-clusters communication. This communication is implemented using an extended version of time-division multiple access (TDMA) allowing the allocation of several slots for a given node, and alternating the role of the clusterhead and its associated overlapping area heads. Each cluster head relays information to overlapping area heads which in turn each relays it to other associated cluster heads in related clusters, thus the information propagates gradually until it reaches the sink in a multi-hop fashion.
文摘The main research objective in wireless sensor networks (WSN) domain is to develop algorithms and protocols to ensure minimal energy consumption with maximum network lifetime. In this paper, we propose a novel design for energy harvesting sensor node and cross-layered MAC protocol using three adjacent layers (Physical, MAC and Network) to economize energy for WSN. The basic idea behind our protocol is to re-energize the neighboring nodes using the radio frequency (RF) energy transmitted by the active nodes. This can be achieved by designing new energy harvesting sensor node and redesigning the MAC protocol. The results show that the proposed cross layer CL_EHSN improves the life time of the WSN by 40%.
文摘Clustering or connected dominating set (CDS) both approaches can establish a virtual backbone (VB) in wireless sensor networks (WSNs) or wireless mesh networks (WMNs). Each cluster consisting of a cluster head (CH) and its neighboring nodes can form a dominating set. After some bridging nodes were selected, cluster heads (CHs) connected through these bridging nodes naturally formed a CDS. Although CDS provides obvious backbone architecture, however, the number of cluster heads and bridging nodes may be too large, this may cause the loss of advantages of virtual backbone. When we effectively reduce their numbers, more effectively WCDS (Weakly Connected Dominating Set) can be fining out. Some essential topics on constructing WCDS-based VB in WSN/WMN are discussed in this paper. From the point of view of three different protocol layers, including network (NWK) layer, MAC layer, and physical (PHY) layer, we explore their cross-layer research topics and design algorithms. For NWK layer, area-based WCDS algorithms and routing strategies including via VB and not via VB are discussed. For MAC layer, a WCDS-based energy-efficient MAC protocol is presented. For PHY layer, battery-aware alternative VB selections and sensor nodes with different transmission ranges are addressed.
文摘Wireless Multimedia Sensor Networks (WMSNs), is a network of sensors, which are limited in terms of memory, computing, bandwidth, and battery lifetime. Multimedia transmission over WSN requires certain QoS guarantees such as huge amount of bandwidth, strict delay and lower loss ratio that makes transmitting multimedia is a complicated task. However, adopting cross-layer approach in WMSNs improves quality of service of WSN under different environmental conditions. In this work, an energy efficient and QoS aware framework for transmitting multimedia content over WSN (EQWSN) is presented, where packet, queue and path scheduling were introduced. It adapts the application layer parameter of video encoder to current wireless channel state, and drops less important packets in case of network congestion according to packet type. Finally, the path scheduling differentiates packets types/priority and route them through different paths with different QoS considering network lifetime. Simulation results show that the new scheme EQWSN transmits video quality with QoS guarantees in addition to prolonging network lifetime.
文摘Advance development of wireless technologies and micro-sensor systems have enabled Wireless Sensor Network (WSN) to emerge as a leading solution in many crucial sensor-based applications. WSN deploys numerous resource-constrained sensor nodes which have limited power supply, memory and computation capability in a harsh environment. Inefficient routing strategy results in degraded network performance in terms of reliability, latency and energy efficiency. In this paper, a cross-layer design, Contention-based MAC and Routing protocol is proposed, termed Contention/SNIR-Based Forwarding (CSBF) protocol. CSBF utilizes the geographical information of sensor nodes to effectively guide the routing direction towards destination node, thereby enhancing reliability. Furthermore, Signal-to-Noise-plus-Interference Ratio (SNIR) metric is used as a routing parameter to guarantee high quality link for data transmission. A Contention-Winner Relay scheme is utilized to reduce the delays caused by the contention procedure. Energy efficiency is also improved by introducing sleep mode technique in CSBF. The simulation work is carried out via OMNeT++ network simulator. The performance of CSBF is compared with other existing routing protocols such as AODV and DSDV in terms of packet delivery ratio (PDR), average end-to-end (ETE) delay and energy consumption per packet. Simulation results highlight that CSBF outperforms AODV and DSDV protocols in respect of PDR and energy efficiency. CSBF also has the most consistent overall network performance.
基金the National High-Tech Research and Development Plan of China (2006AA01Z223)the China Next Generation Internet (CNGI) Plan (2005-2137).
文摘With the development of CMOS and MEMS technologies, the implementation of a large number of wireless distributed micro-sensors that can be easily and rapidly deployed to form highly redundant, self-configuring, and ad hoc sensor networks. To facilitate ease of deployment, these sensors operate on battery for extended periods of time. A particular challenge in maintaining extended battery lifetime lies in achieving communications with low power. For better understanding of the design tradeoffs of wireless sensor network （WSN）, a more accurate energy model for wireless sensor node is proposed, and an optimal design method of energy efficient wireless sensor node is described as well. Different from power models ever shown which assume the power cost of each component in WSN node is constant, the new one takes into account the energy dissipation of circuits in practical physical layer. It shows that there are some parameters, such as data rate, carrier frequency, bandwidth, Tsw, etc, which have a significant effect on the WSN node energy consumption per useful bit （EPUB）. For a given quality specification, how energy consumption can be reduced by adjusting one or more of these parameters is shown.
基金supported by the National Natural Science Foundation of China(Grant no. 61202399,61571063)
文摘This work is about the development of a super low noise amplifier with minimum power consumption and high gain for several wireless applications.The amplifier operates at frequency bands of 0.9-2.4 GHz and can be used in many applications like Wireless local area network(WLAN),WiFi,Bluetooth,ZigBee and Global System for mobile communications(GSM).This new design can be employed for the IEEE 802.15.4 standard in industrial,scientific and medical(ISM) Band.The enhancement mode pseudomorphic high electron mobility transistor PHEMT is used here due to its high linearity,better performance and less noisy operation.The common source inductive degeneration method is employed here to enhance the gain of amplifier.The amplifier produces a gain of more than 17 dB and noise figure of about 0.5 dB.The lower values of S11 and S22 reflect the accuracy of impedance matching network placed at the input and output sides of amplifier.Agilent Advance Design System(ADS) is used for the design and simulation purpose.Further the layout of design is developed on the FR4 substrate.
文摘Complex and distributed systems are more and more associated with the application of WSN (Wireless Sensor Network) technology. The design of such applications presents important challenges and requires the assistance of several methodologies and tools. Multi-Agent systems (MAS) have been identified as one of the most suitable technologies to contribute to this domain due to their appropriateness for modeling distributed and autonomous complex systems. This work aims to contribute in the help of the design of WSN applications. The proposed architecture exploits the advantages of MAS for modeling WSN services, network topologies and sensor device architectures.
文摘Communication over wireless links identifies significant challenges for routing protocols operating. This paper proposes a Cross-layer design based Multipath Routing Protocol (CMRP) for mobile ad hoc networks, by means of the node energy signal from the physical layer. The purpose is to optimize routing decision and path quality. The nodes’ mobility behavior is predicted using a notion of “Signal Fading Degree, SFD”. Especially, in combination of the IEEE 802.11e standard at the MAC layer, we determine that the IEEE 802.11e makes a significant contribution to performance improvement of CMRP. Performance evaluation of AODV in legacy 802.11 and CMRP in IEEE 802.11e shows that, as a function of speed of node mobility, a tremendous reduction achieved, in metrics such as the average end-to-end delay, route overhead, route discovery frequency, normalized routing load - almost more than 80%, 40%, 40%, and 40%. In the case of varying number of sessions, the reduction for route discovery frequency and normalized routing load are up to 70% and 80%.
