Fully developed turbulence measurements in pipe flow were made in theReynolds number range from 10 X 10~3 to 350 X 10~3 with hot-wire anemometer and a Pilot tube.Comparisons were made with the experimental results of ...Fully developed turbulence measurements in pipe flow were made in theReynolds number range from 10 X 10~3 to 350 X 10~3 with hot-wire anemometer and a Pilot tube.Comparisons were made with the experimental results of previous researchers. The mean velocityprofile and the turbulent intensity in the experiments indicate that for the mean velocity profile,in the fully developed turbulent pipe flow, von Karman's constant κ is a function of the Reynoldsnumber, i. e. κ increases slowly with the Reynolds number. For turbulent pipe flow, the outer limitdepends on whether the Kdrmdn number R^+ is greater or less than 850 in the centerline velocityprofile: a log law exists for 850 < R^+< 1750 in the experiment, and von Karman' s constant κ isshown to be 0. 408. Under the effects of the test trip at the inlet, fully developed turbulence wasobtained in pipe flow at lower Reynolds number when the entrance length (x/D) was larger than 40. Inthe experiment it was also found that turbulence quantities in pipe flow remain independent of theupstream conditions when the trip blockage ratio is higher than 20%, and the comparison with channelwater flow was also performed.展开更多
The tensile behavior of(Fe_(50)Mn_(30)Co_(10)Cr_(10))_(100-x)Si_(x)(x=0(Si0),2(Si2))metastable HEAs prepared by selective laser melting was studied at cryogenic temperatures.The results demonstrate that the addition o...The tensile behavior of(Fe_(50)Mn_(30)Co_(10)Cr_(10))_(100-x)Si_(x)(x=0(Si0),2(Si2))metastable HEAs prepared by selective laser melting was studied at cryogenic temperatures.The results demonstrate that the addition of Si leads to lattice distortion and a decrease in stacking fault energy,especially at 77 K,which significantly promotes transformation-induced plasticity(TRIP)in Si2 HEAs.The yield strength,tensile strength,and ductility of Si2 HEAs are 505.2 MPa,1364.1 MPa,and 19%,which are 43%,53% and 58% higher than those of Si0 alloy,respectively.TRIP is the main deformation mode,in addition to dislocation slip,and plays a key role in strengthening.The reinforced and continuously sustained TRIP maintains a dynamic strain distribution during deformation.Ultrahigh strain hardening greatly enhances the strength and ductility.展开更多
Control of the formation and stability of reverted austenite is critical in achieving a favorable combination of strength,ductility,and toughness in high-strength steels.In this work,the effects of Cu precipitation on...Control of the formation and stability of reverted austenite is critical in achieving a favorable combination of strength,ductility,and toughness in high-strength steels.In this work,the effects of Cu precipitation on the austenite reversion and mechanical properties of maraging stainless steels were investigated by atom probe tomography,transmission electron microscopy,and mechanical tests.Our results indicate that Cu accelerates the austenite reversion kinetics in two manners:first,Cu,as an austenite stabilizer,increases the equilibrium austenite fraction and hence enhances the chemical driving force for the austenite formation,and second,Cu-rich nanoprecipitates promote the austenite reversion by serving as heterogeneous nucleation sites and providing Ni-enriched chemical conditions through interfacial segregation.In addition,the Cu precipitation hardening compensates the strength drop induced by the formation of soft reverted austenite.During tensile deformation,the metastable reverted austenite transforms to martensite,which substantially improves the ductility and toughness through a transformation-induced plasticity(TRIP)effect.The Cu-added maraging stainless steel exhibits a superior combination of a yield strength of~1.3 GPa,an elongation of~15%,and an impact toughness of~58 J.展开更多
A three-step cooling pattern on the runout table（ROT）was conducted for the hot rolled TRIP steel.Microstructural evolution during thermomechanical controlled processing（TMCP）was investigated.Processing condition o...A three-step cooling pattern on the runout table（ROT）was conducted for the hot rolled TRIP steel.Microstructural evolution during thermomechanical controlled processing（TMCP）was investigated.Processing condition of controlled cooling on a ROT in the laboratory rolling mill was discussed.The results indicated that the microstructure containing polygonal ferrite,granular bainite and a significant amount of the stable retained austenite can be obtained through three-step cooling on the ROT after hot rolling.TMCP led to ferrite grain refinement.Controlled cooling after hot rolling resulted in the stability of the remaining austenite and a satisfactory TRIP effect.Excellent mechanical properties were obtained through TMCP for the hot rolled TRIP steel.展开更多
The controlled cooling technology following hot rolling process is a vital factor that affects the final micro- structure and mechanical properties of the hot-rolled transformation induced plasticity （TRIP） steels. ...The controlled cooling technology following hot rolling process is a vital factor that affects the final micro- structure and mechanical properties of the hot-rolled transformation induced plasticity （TRIP） steels. In the present study, low alloy C-Si-Mn TRIP steel was successfully fabricated by hot rolling process with a 4450 hot roiling mill. To maximize the volume fraction and stability of retained austenite of the steel, two different cooling methods （aircooling and ultra-fast cooling ＂AC-UFC＂ and ultrmfast cooling, air cooling and ultra-fast cooling ＂UFC-AC-UFC＂） were conducted. The effects of the cooling method on the microstructure of hot-rolled TRIP steel were investigated via optical microscope, transmission electron microscope and conversion electron Mossbauer spectroscope. The mechanical properties of the steel were also evaluated by conventional tensile test. The results indicated that ferrite and bainite in the microstructure were refined with the cooling method of UFC-AC-UFC. The morphology of retained austenite was also changed from small islands distributing in bainite district （obtained with AC-UFC） to granular shape locating at the triple junction of the ferrite grain boundaries （obtained with UFC-AC-UFC）. As a result, the TRIP steel with a content of retained austenite of 11. 52%, total elongation of 32% and product of tensile strength and total elongation of 27 552 MPa·% was obtained.展开更多
The effects of Mn and Cr contents on bainitic transformation kinetics,microstructures and mechanical properties of high-carbon low alloy steels after austempered at 230,300 and 350 ℃ were determined by dilatometry,op...The effects of Mn and Cr contents on bainitic transformation kinetics,microstructures and mechanical properties of high-carbon low alloy steels after austempered at 230,300 and 350 ℃ were determined by dilatometry,optical microscopy,scanning electron microscopy,X-ray diffraction and tensile tests. The results showed that Mn and Cr can extend bainitic incubation period and completion time,and with the increase of Mn and Cr content,the bainitic ferrite plate thickness decreased and the volume fraction of retained austenite increased. TRIP（ transformation induced plasticity） effect was observed during tensile testing which improved the overall mechanical property. The increase of Mn concentration can improve the strength to a certain extent,but reduce the ductility. The increase of Cr concentration can improve the ductility of bainitic steels which transformed at a low temperature. The low temperature bainitic steel austempered at 230 ℃ exhibited excellent mechanical properties with ultimate tensile strength of（ 2146 ± 11） MPa and total elongation of（ 12. 95 ± 0. 15） %.展开更多
A hot-rolled medium Mn(0.2C5Mn)steel is annealed at 650℃ to produce an ultrafine-grained duplex microstructure with different austenite volume fractions by austenite reverted transformation(ART)annealing,and the orie...A hot-rolled medium Mn(0.2C5Mn)steel is annealed at 650℃ to produce an ultrafine-grained duplex microstructure with different austenite volume fractions by austenite reverted transformation(ART)annealing,and the orientation relationship strictly obeys K-S orientation relationship before deformation.Tensile tests are carried out in a temperature range from-196 to 400℃ to examine the effects of the austenite volume fraction and the deformation temperature on the tensile properties and the austenite stability.Microstructural observations reveal that the metastable austenite gradually transformed into a-martensite,which is controlled by the deformation strain,the temperature and the austenite volume fraction.Both strain hardening behavior and ductility of the studied steel are dependent on austenite volume fraction and deformation temperature significantly.The stress-strain curves of ART-annealed 0.2C5Mn steel assume an S shape and a very large work hardening rate of about 10 GPa is obtained at liquid nitrogen deformation temperature.Based on the experimental data,a quantitative relation is proposed to describe the ductility dependence on both the austenite volume fraction and its mechanical stability.展开更多
Forest bathing trip is a short, leisurely visit to forest. In this study we determined the health effects of forest bathing trip on elderly patients with chronic obstructive pulmonary disease （COPD）. The patients we...Forest bathing trip is a short, leisurely visit to forest. In this study we determined the health effects of forest bathing trip on elderly patients with chronic obstructive pulmonary disease （COPD）. The patients were randomly divided into two groups. One group was sent to forest, and the other was sent to an urban area as control. Flow cytometry, ELISA, and profile of mood states （POMS） evaluation were performed. In the forest group,展开更多
Influence of different electric current modes （pulse and direct） on occurrence of the electroplastic effect under uniaxialtension in the coarse-grained alloys with martensite transformations is investigated. The mat...Influence of different electric current modes （pulse and direct） on occurrence of the electroplastic effect under uniaxialtension in the coarse-grained alloys with martensite transformations is investigated. The materials are shape memoryTi49.3Niso.7 alloy and metastable austenite transformation-induced plasticity （TRIP） steel. The paper contains experimentalresults of current impact on the ＂stress-strain＂ curves of the material. It has been taken an experimental measurement ofthe sample temperature during the test. It is shown that the shape of a stress-strain curves and type of the serrate plasticflow, connected with the martensitic transformation and electroplastic effect, depend on the current modes. Impact of pulsecurrent and direct current suppresses shape memory and TRIP effect.展开更多
The effect of thermomechanical control processing（TMCP）on microstructure and mechanical properties of Fe-0.2C-1.44Si-1.32Mn hot rolled TRIP steel was investigated through experiments.Strain-induced transformation an...The effect of thermomechanical control processing（TMCP）on microstructure and mechanical properties of Fe-0.2C-1.44Si-1.32Mn hot rolled TRIP steel was investigated through experiments.Strain-induced transformation and transformation-induced plasticity behavior of retained austenite were analyzed.The results show that with multipass deformation,reduction per pass of more than critical deformation in austenite recrystallization region and total reduction of more than 58% in non-recrystallization region and high temperature section of two-phase region,austenite can be refined before γ→α transformation.It is beneficial to obtain refined ferrite grain in final microstructure.To obtain fine and uniform microstructure and excellent strength-ductility balance,a three-stage cooling process（laminar cooling-air cooling-ultra-fast cooling）after hot rolling was conducted.The ultimate tensile strength and elongation of the investigated steel can reach 663 MPa and 41%,respectively.展开更多
Warm deformation tests were performed using a kind of tubby heater. The microstructures and mechanical properties of an Fe-C-Mn-Si multiphase steel resulting from different warm deformation temperatures were investiga...Warm deformation tests were performed using a kind of tubby heater. The microstructures and mechanical properties of an Fe-C-Mn-Si multiphase steel resulting from different warm deformation temperatures were investiga- ted by using LOM （light optical microscopy）, SEM and XRD. The results indicated that the microstructure contai- ning polygonal ferrite, granular bainite and a significant amount of the stable retained austenite can be obtained through hot deformation and subsequent austempering. Warm deformation temperature affects the mechanical prop- erties of the hot rolled TRIP steels. Ultimate tensile strength balance reached maximum （881 MPa） when the speci- men was deformed at 250 ~C, and the total elongation and strength-ductility reached maximum （38% and 28 614 MPa ~ ~, respectively） at deforming temperature of 100 ~C. Martensite could nucleate when austenite was deformed above M~, because mechanical driving force compensates the decrease of chemical driving force. The TRIP effect occurs in the Fe-C-Mn-Si multiphase steel at deforming temperature ranging from 15 to 350 ~C. The results of the effects of warm deformation on the mechanical properties of the Fe-C-Mn-Si multiphase steel can provide theoretical basis for the ap- plications and the warm working of the hot rolled TRIP sheet steels in industrial manufacturing.展开更多
High-strength steel with excellent ductility is pivotal for the formability and safety of critical structural components.Here,a heterogeneous metastable lamellar steel,composed of alternating lamellar ferrite and aust...High-strength steel with excellent ductility is pivotal for the formability and safety of critical structural components.Here,a heterogeneous metastable lamellar steel,composed of alternating lamellar ferrite and austenite aligned with the rolling direction,was developed through an innovative combination of warm rolling and immediate annealing processes.This novel design overcomes the strength-ductility trade-off,achieving high ultimate tensile strength(∼1.2 GPa)and excellent uniform elongation(∼78%),pushing the product of ultimate tensile strength and uniform elongation to an ultra-high level(>90 GPa%).The high tensile strength is attributed to ultrafine lamellar grains and significant work hardening induced by the hetero-deformation and transformation-induced plasticity(TRIP)effect.The exceptional ductility is a result of the synergy of multiple plasticity mechanisms,including(i)the inherent plastic deformation ability of lamellar microstructure and the hetero-deformation-induced hardening in the early deformation period,(ii)the persistent TRIP effect induced by the lamellar austenite with high mechanical stability and the elimination of strain localization caused by prolonged strain hardening due to the coordinated deformation of lamellar austenite and ferrite in the middle deformation period,and(iii)delamination cracking in the late deformation period.This approach adopted in current work offers a straightforward and economically feasible pathway for fabricating advanced high-strength steel with superior performance.展开更多
As a representative of the third generation advanced high-strength steels(AHSSs),medium Mn steels(MMS)have broad development prospects in the field of automobile manufacturing.MMS with typical austenite reversion trea...As a representative of the third generation advanced high-strength steels(AHSSs),medium Mn steels(MMS)have broad development prospects in the field of automobile manufacturing.MMS with typical austenite reversion treatment have a soft duplex microstructure,i.e.ferrite+austenite,presenting a high ductility but a low yield strength.Here we show that a flash heating and cooling after austenite reversion treatment can replace the ferrite with strong martensite,which greatly enhances the yield strength of a 0.25C-4Mn steel by about 461–886 MPa.By adjusting the reversion temperature before the flash treatment,the C and Mn concentrations of reverted austenite can be altered,which determine the fraction of reverted austenite surviving the flash treatment.In addition,the mechanical stability of final retained austenite is also linked to the reversion temperature,resulting different work hardening behaviors due to transformation induced plasticity(TRIP)effect.By tweaking the reversion temperature before the flash treatment,an optimized combination of strength and ductility can be achieved.The micromechanical differences caused by the replacement of the matrix are also investigated via in-situ digital image correlation method.展开更多
The martensitic hot-rolled 0.3 C-6 Mn-1.5 Si(wt%)steel was annealed at 630℃for 24 h to improve its cold rollability,followed by cold rolling and annealing at 670℃for 10 min.The annealing process was designed based o...The martensitic hot-rolled 0.3 C-6 Mn-1.5 Si(wt%)steel was annealed at 630℃for 24 h to improve its cold rollability,followed by cold rolling and annealing at 670℃for 10 min.The annealing process was designed based on the capacities of industrial batch annealing and continuous annealing lines.A duplex submicron austenite and ferrite microstructure and excellent tensile properties were obtained finally,proved the above process is feasible."Austenite memory"was found in the hot-rolled and annealed sample which restricted recrystallization of lath martensite,leading to lath-shaped morphology of austenite and ferrite grains."Austenite memory"disappeared in the cold-rolled and annealed sample due to austenite random nucleation and ferrite recrystallization,resulting in globular microstructure and refinement of both austenite and ferrite grains.The austenite to martensite transformation contributed most of strain hardening during deformation and improved the uniform elongation,but the dislocation strengthening played a decisive role on the yielding behavior.The tensile curves change from continuous to discontinuous yielding as the increase of cold-rolled reduction due to the weakening dislocation strengthening of austenite and ferrite grains related to the morphology change and grain refinement.A method by controlling the cold-rolled reduction is proposed to avoid the Lüders strain.展开更多
Both microstrueture and mechanical properties of low alloy steels treated by quenching and partitioning （Q＆P） process were examined. The mixed microstructure of martensite and large-fractioned retained austenite （...Both microstrueture and mechanical properties of low alloy steels treated by quenching and partitioning （Q＆P） process were examined. The mixed microstructure of martensite and large-fractioned retained austenite （about 27.3%） was characterized and analyzed, excellent combinations of total elongation of 19% and tensile strength of 1 835 MPa were obtained, and three-stage work hardening behavior was demonstrated during tensile test. The en hanced mechanical properties and work hardening behavior were explained based on the transformation induced plas ticity effect of large fractioned austenite.展开更多
High-Si spring steel was heat treated in three different ways： Quenching and tempering at 460 ℃ to obtain a tempered martensite microstructure, and austempering at 300 and 350 ℃, respectively, to obtain two differe...High-Si spring steel was heat treated in three different ways： Quenching and tempering at 460 ℃ to obtain a tempered martensite microstructure, and austempering at 300 and 350 ℃, respectively, to obtain two different carbide-free bainitic microstructures. In the steel austempered at 350 ℃, both the bainite lath thickness and retained austenite content were higher than those of the steel austempered at 300 ℃. Rotating-bending fatigue tests were done in order to evaluate the effect of each heat treatment on the high-cycle fatigue behavior of the steel. When the austempering temperature was 300 ℃, the endurance limit was increased by 25% despite a 5% reduction in tensile strength when compared with that of the quenched and tempered steel. The relationship between endurance limit [Rfat （50~）] and ultimate tensile strength （Rm） was higher for the austempered samples in comparison with that of the quenched and tempered material. Therefore, it is believed that the presence of retained austenite affects the relationship between endurance limit and tensile strength.展开更多
Strain-induced martensites in high manganese TRIP/TWIP steels were investigated in the presence of thermal martensites and under the influence of austenitic grain orientation by X-ray diffraction （XRD）, scanning ele...Strain-induced martensites in high manganese TRIP/TWIP steels were investigated in the presence of thermal martensites and under the influence of austenitic grain orientation by X-ray diffraction （XRD）, scanning electron microscopy （SEM） and electron backscattered diffraction （EBSD）. Before deformation, the morphology of α＇- M depended mainly on the number of variants and growing period. Regardless of martensite morphologies and deformation, the Kurdjumov-Sachs （K-S） orientation relationships always maintained. The 6 α＇-M variants formed from a plate of ε-M were of 3 pairs of twins with a common axis 〈110〉α＇ parallel to the normal of {112}γ habit plane to minimize transformation strain. When α＇-M could be formed only by deformation, it nucleated at the intersection of ε-M variants and grew mainly in thick ε-M plates. Thick ε plates promoted significantly the α＇-M and weakened the influence of grain orientations. During tension, the transformation in 〈100〉-oriented grains was observed to be slower than that in 〈121〉-oriented grains. Deformation twins promoted ε-M formation slightly and had no apparent effect on α＇-M. Deformation increased the number of ε-M variants, but reduced that of α＇-M variants.展开更多
Enhancing the ductility and toughness of advanced high-strength steels is essential for the wide range of promising applications.The retained austenite(RA)is a key phase due to the austenite-to-martensite transformati...Enhancing the ductility and toughness of advanced high-strength steels is essential for the wide range of promising applications.The retained austenite(RA)is a key phase due to the austenite-to-martensite transformation and its transformation-induced plasticity effect.It is commonly accepted that slow RA-to-martensite transformation is beneficial to ductility;therefore,the RA fraction and stability should be carefully controlled.The RA stability is related to its morphology,size,carbon content,neighboring phase and orientation.Importantly,these factors are cross-influenced.It is noteworthy that the influence of RA on ductility and fracture toughness is not consistent because of their difference in stress state.There is no clear relationship between fracture toughness and tensile properties.Thus,it is important to understand the role of RA in toughness.The toughness is enhanced during the RA-to-martensite transformation,while the fracture toughness is decreased due to the formation of fresh and brittle martensite.As a result,the findings regarding to the effect of RA on fracture toughness are conflicting.Further investigations should be conducted in order to fully understand the effects of RA on ductility and fracture toughness,which can optimize the combination of ductility and toughness in AHSSs.展开更多
The Luders deformation behavior in a medium Mn transformation induced plasticity （TRIP） steel is investigated at different temperatures ranging from 25 to 300 ℃. It demonstrates that the Ltiders band appears at all...The Luders deformation behavior in a medium Mn transformation induced plasticity （TRIP） steel is investigated at different temperatures ranging from 25 to 300 ℃. It demonstrates that the Ltiders band appears at all testing temperatures but with varied Luders strains which do not change monoton ically with temperature. The martensitic transformation is simultaneously observed within the Ltiders band in varying degrees depending on the testing temperature. It is well verified that the martensitic transformation is not responsible for the formation of Luders band, and a reasonable explanation is given for the non-monotonic variation of Luders strain with increasing temperature.展开更多
Nanoprecipitates and nanoscale retained austenite(RA)with suitable stability play crucial roles in deter-mining the yield strength(YS)and ductility of ultrahigh strength steels(UHSSs).However,owing to the kinetics inc...Nanoprecipitates and nanoscale retained austenite(RA)with suitable stability play crucial roles in deter-mining the yield strength(YS)and ductility of ultrahigh strength steels(UHSSs).However,owing to the kinetics incompatibility between nanoprecipitation and austenite reversion,it is highly challenging to si-multaneously introduce high-density nanoprecipitates and optimized RA in UHSSs.In this work,through the combination of austenite reversion treatment(ART)and subsequent flash austenitizing(FA),nanoscale chemical heterogeneity was successfully introduced into a low-cost UHSS prior to the aging process.This chemical heterogeneity involved the enrichment of Mn and Ni in the austenite phase.The resulting UHSS exhibited dual-nanoprecipitation of Ni(Al,Mn)and(Mo,Cr)_(2)C and nanoscale austenite stabilized via Mn and Ni enrichment.The hard martensitic matrix strengthened by high-density dual-nanoprecipitates con-strains the plastic deformation of soft RA with a relatively low fraction of-15%,and the presence of relatively stable nanoscale RA with adequate Mn and Ni enrichment leads to a marginal loss in YS but keeps a persistent transformation-induced plasticity(TRIP)effect.As a result,the newly-developed UHSS exhibits an ultrahigh YS of-1.7 GPa,an ultimate tensile strength(UTS)of-1.8 GPa,a large uniform elongation(UE)of-8.5%,and a total elongation(TE)of-13%.The strategy of presetting chemical heterogeneity to introduce proper metastable phases before aging can be extended to other UHSSs and precipitation-hardened alloys.展开更多
文摘Fully developed turbulence measurements in pipe flow were made in theReynolds number range from 10 X 10~3 to 350 X 10~3 with hot-wire anemometer and a Pilot tube.Comparisons were made with the experimental results of previous researchers. The mean velocityprofile and the turbulent intensity in the experiments indicate that for the mean velocity profile,in the fully developed turbulent pipe flow, von Karman's constant κ is a function of the Reynoldsnumber, i. e. κ increases slowly with the Reynolds number. For turbulent pipe flow, the outer limitdepends on whether the Kdrmdn number R^+ is greater or less than 850 in the centerline velocityprofile: a log law exists for 850 < R^+< 1750 in the experiment, and von Karman' s constant κ isshown to be 0. 408. Under the effects of the test trip at the inlet, fully developed turbulence wasobtained in pipe flow at lower Reynolds number when the entrance length (x/D) was larger than 40. Inthe experiment it was also found that turbulence quantities in pipe flow remain independent of theupstream conditions when the trip blockage ratio is higher than 20%, and the comparison with channelwater flow was also performed.
基金supported by Program for Innovative Research Team in Science and Technology in Fujian Province University,Chinathe Natural Science Foundation of Fujian Province,China(Nos.2023J011013,2020J01898)。
文摘The tensile behavior of(Fe_(50)Mn_(30)Co_(10)Cr_(10))_(100-x)Si_(x)(x=0(Si0),2(Si2))metastable HEAs prepared by selective laser melting was studied at cryogenic temperatures.The results demonstrate that the addition of Si leads to lattice distortion and a decrease in stacking fault energy,especially at 77 K,which significantly promotes transformation-induced plasticity(TRIP)in Si2 HEAs.The yield strength,tensile strength,and ductility of Si2 HEAs are 505.2 MPa,1364.1 MPa,and 19%,which are 43%,53% and 58% higher than those of Si0 alloy,respectively.TRIP is the main deformation mode,in addition to dislocation slip,and plays a key role in strengthening.The reinforced and continuously sustained TRIP maintains a dynamic strain distribution during deformation.Ultrahigh strain hardening greatly enhances the strength and ductility.
基金financial support from the National Natural Science Foundation of China(51801169)State Key Laboratory for Advanced Metals and Materials Open Fund(2017-ZD01)+5 种基金Chinese National Engineering Research Centre for Steel Construction(Hong Kong Branch)at PolyU(P0013862)Guangzhou International Science&Technology Cooperation Program(201907010026)financial support from the Youth Innovation Promotion Association of Chinese Academy of Sciences(2017233)the Innovation Project of Institute of Metal Research(2015-ZD04)the National Natural Science Foundation of China Research Fund for International Young Scientists(No.51750110515)the National Natural Science Foundation of China(No.51472249)。
文摘Control of the formation and stability of reverted austenite is critical in achieving a favorable combination of strength,ductility,and toughness in high-strength steels.In this work,the effects of Cu precipitation on the austenite reversion and mechanical properties of maraging stainless steels were investigated by atom probe tomography,transmission electron microscopy,and mechanical tests.Our results indicate that Cu accelerates the austenite reversion kinetics in two manners:first,Cu,as an austenite stabilizer,increases the equilibrium austenite fraction and hence enhances the chemical driving force for the austenite formation,and second,Cu-rich nanoprecipitates promote the austenite reversion by serving as heterogeneous nucleation sites and providing Ni-enriched chemical conditions through interfacial segregation.In addition,the Cu precipitation hardening compensates the strength drop induced by the formation of soft reverted austenite.During tensile deformation,the metastable reverted austenite transforms to martensite,which substantially improves the ductility and toughness through a transformation-induced plasticity(TRIP)effect.The Cu-added maraging stainless steel exhibits a superior combination of a yield strength of~1.3 GPa,an elongation of~15%,and an impact toughness of~58 J.
基金Item Sponsored by National Natural Science Foundation of China(50334010)
文摘A three-step cooling pattern on the runout table（ROT）was conducted for the hot rolled TRIP steel.Microstructural evolution during thermomechanical controlled processing（TMCP）was investigated.Processing condition of controlled cooling on a ROT in the laboratory rolling mill was discussed.The results indicated that the microstructure containing polygonal ferrite,granular bainite and a significant amount of the stable retained austenite can be obtained through three-step cooling on the ROT after hot rolling.TMCP led to ferrite grain refinement.Controlled cooling after hot rolling resulted in the stability of the remaining austenite and a satisfactory TRIP effect.Excellent mechanical properties were obtained through TMCP for the hot rolled TRIP steel.
基金Key Projects in National Science and Technology Pillar Program During the Eleventh Five-Year Plan Period of China(2006BAE03A08)
文摘The controlled cooling technology following hot rolling process is a vital factor that affects the final micro- structure and mechanical properties of the hot-rolled transformation induced plasticity （TRIP） steels. In the present study, low alloy C-Si-Mn TRIP steel was successfully fabricated by hot rolling process with a 4450 hot roiling mill. To maximize the volume fraction and stability of retained austenite of the steel, two different cooling methods （aircooling and ultra-fast cooling ＂AC-UFC＂ and ultrmfast cooling, air cooling and ultra-fast cooling ＂UFC-AC-UFC＂） were conducted. The effects of the cooling method on the microstructure of hot-rolled TRIP steel were investigated via optical microscope, transmission electron microscope and conversion electron Mossbauer spectroscope. The mechanical properties of the steel were also evaluated by conventional tensile test. The results indicated that ferrite and bainite in the microstructure were refined with the cooling method of UFC-AC-UFC. The morphology of retained austenite was also changed from small islands distributing in bainite district （obtained with AC-UFC） to granular shape locating at the triple junction of the ferrite grain boundaries （obtained with UFC-AC-UFC）. As a result, the TRIP steel with a content of retained austenite of 11. 52%, total elongation of 32% and product of tensile strength and total elongation of 27 552 MPa·% was obtained.
基金supported by the National Natural Science Foundation of China(Grant No.51271035 and U1560107)The financial support of the State Key Laboratory of Development and Application Technology of Automotive Steels
文摘The effects of Mn and Cr contents on bainitic transformation kinetics,microstructures and mechanical properties of high-carbon low alloy steels after austempered at 230,300 and 350 ℃ were determined by dilatometry,optical microscopy,scanning electron microscopy,X-ray diffraction and tensile tests. The results showed that Mn and Cr can extend bainitic incubation period and completion time,and with the increase of Mn and Cr content,the bainitic ferrite plate thickness decreased and the volume fraction of retained austenite increased. TRIP（ transformation induced plasticity） effect was observed during tensile testing which improved the overall mechanical property. The increase of Mn concentration can improve the strength to a certain extent,but reduce the ductility. The increase of Cr concentration can improve the ductility of bainitic steels which transformed at a low temperature. The low temperature bainitic steel austempered at 230 ℃ exhibited excellent mechanical properties with ultimate tensile strength of（ 2146 ± 11） MPa and total elongation of（ 12. 95 ± 0. 15） %.
基金This research was supported by both National Natural Science Foundation of China(NSFC,Nos.51871062,51371057 and 11672195)MNSF of Beijing(No.2182088)Chong-xiang Huang acknowledged Sichuan Youth Science and Technology Foundation(No.2016JQ0047).
文摘A hot-rolled medium Mn(0.2C5Mn)steel is annealed at 650℃ to produce an ultrafine-grained duplex microstructure with different austenite volume fractions by austenite reverted transformation(ART)annealing,and the orientation relationship strictly obeys K-S orientation relationship before deformation.Tensile tests are carried out in a temperature range from-196 to 400℃ to examine the effects of the austenite volume fraction and the deformation temperature on the tensile properties and the austenite stability.Microstructural observations reveal that the metastable austenite gradually transformed into a-martensite,which is controlled by the deformation strain,the temperature and the austenite volume fraction.Both strain hardening behavior and ductility of the studied steel are dependent on austenite volume fraction and deformation temperature significantly.The stress-strain curves of ART-annealed 0.2C5Mn steel assume an S shape and a very large work hardening rate of about 10 GPa is obtained at liquid nitrogen deformation temperature.Based on the experimental data,a quantitative relation is proposed to describe the ductility dependence on both the austenite volume fraction and its mechanical stability.
基金supported by funds from the National Natural Science Foundation of China(31301139&31201040)funds from Science Technology Department of Zhejiang Province(2012C24005&2014C33130)+2 种基金Health Bureau of Zhejiang Province(11-CX01&2013ZDA002)Zhejiang Provincial Key Disciplinary Fields of Geriatrics Program
文摘Forest bathing trip is a short, leisurely visit to forest. In this study we determined the health effects of forest bathing trip on elderly patients with chronic obstructive pulmonary disease （COPD）. The patients were randomly divided into two groups. One group was sent to forest, and the other was sent to an urban area as control. Flow cytometry, ELISA, and profile of mood states （POMS） evaluation were performed. In the forest group,
基金supported by the Competitiveness Program of the National Research Nuclear University MEPhI(Moscow Engineering Physics Institute)the Ministry of Education and Science of the Russian Federation No.02.A03.21.0005,27.08.2013,and RFBR(project#16-58-48001)
文摘Influence of different electric current modes （pulse and direct） on occurrence of the electroplastic effect under uniaxialtension in the coarse-grained alloys with martensite transformations is investigated. The materials are shape memoryTi49.3Niso.7 alloy and metastable austenite transformation-induced plasticity （TRIP） steel. The paper contains experimentalresults of current impact on the ＂stress-strain＂ curves of the material. It has been taken an experimental measurement ofthe sample temperature during the test. It is shown that the shape of a stress-strain curves and type of the serrate plasticflow, connected with the martensitic transformation and electroplastic effect, depend on the current modes. Impact of pulsecurrent and direct current suppresses shape memory and TRIP effect.
基金Item Sponsored by National Fundamental Project of Science and Technology of China(ZZ0113A0101)
文摘The effect of thermomechanical control processing（TMCP）on microstructure and mechanical properties of Fe-0.2C-1.44Si-1.32Mn hot rolled TRIP steel was investigated through experiments.Strain-induced transformation and transformation-induced plasticity behavior of retained austenite were analyzed.The results show that with multipass deformation,reduction per pass of more than critical deformation in austenite recrystallization region and total reduction of more than 58% in non-recrystallization region and high temperature section of two-phase region,austenite can be refined before γ→α transformation.It is beneficial to obtain refined ferrite grain in final microstructure.To obtain fine and uniform microstructure and excellent strength-ductility balance,a three-stage cooling process（laminar cooling-air cooling-ultra-fast cooling）after hot rolling was conducted.The ultimate tensile strength and elongation of the investigated steel can reach 663 MPa and 41%,respectively.
基金Sponsored by National Natural Science Foundation of China (50334010)
文摘Warm deformation tests were performed using a kind of tubby heater. The microstructures and mechanical properties of an Fe-C-Mn-Si multiphase steel resulting from different warm deformation temperatures were investiga- ted by using LOM （light optical microscopy）, SEM and XRD. The results indicated that the microstructure contai- ning polygonal ferrite, granular bainite and a significant amount of the stable retained austenite can be obtained through hot deformation and subsequent austempering. Warm deformation temperature affects the mechanical prop- erties of the hot rolled TRIP steels. Ultimate tensile strength balance reached maximum （881 MPa） when the speci- men was deformed at 250 ~C, and the total elongation and strength-ductility reached maximum （38% and 28 614 MPa ~ ~, respectively） at deforming temperature of 100 ~C. Martensite could nucleate when austenite was deformed above M~, because mechanical driving force compensates the decrease of chemical driving force. The TRIP effect occurs in the Fe-C-Mn-Si multiphase steel at deforming temperature ranging from 15 to 350 ~C. The results of the effects of warm deformation on the mechanical properties of the Fe-C-Mn-Si multiphase steel can provide theoretical basis for the ap- plications and the warm working of the hot rolled TRIP sheet steels in industrial manufacturing.
基金support from the National Natural Science Foundation of China(Grant No.52304389)the China Postdoctoral Science Foundation(No.2022M720402)+2 种基金Huibin Wu and Gang Niu appreciate the support from the Fundamental Research Funds for the Central Universities(No.FRF-BD-23-01)Na Gong appreciates the support from the Structural Metal Alloy Program(SMAP,No.A18B1b0061)Gang Niu is grateful to Hatem S.Zurob for his insightful recommendation and expressive discussion.
文摘High-strength steel with excellent ductility is pivotal for the formability and safety of critical structural components.Here,a heterogeneous metastable lamellar steel,composed of alternating lamellar ferrite and austenite aligned with the rolling direction,was developed through an innovative combination of warm rolling and immediate annealing processes.This novel design overcomes the strength-ductility trade-off,achieving high ultimate tensile strength(∼1.2 GPa)and excellent uniform elongation(∼78%),pushing the product of ultimate tensile strength and uniform elongation to an ultra-high level(>90 GPa%).The high tensile strength is attributed to ultrafine lamellar grains and significant work hardening induced by the hetero-deformation and transformation-induced plasticity(TRIP)effect.The exceptional ductility is a result of the synergy of multiple plasticity mechanisms,including(i)the inherent plastic deformation ability of lamellar microstructure and the hetero-deformation-induced hardening in the early deformation period,(ii)the persistent TRIP effect induced by the lamellar austenite with high mechanical stability and the elimination of strain localization caused by prolonged strain hardening due to the coordinated deformation of lamellar austenite and ferrite in the middle deformation period,and(iii)delamination cracking in the late deformation period.This approach adopted in current work offers a straightforward and economically feasible pathway for fabricating advanced high-strength steel with superior performance.
基金National Key R&D Program of China(Grant Nos.2022YFE0110800 and 2022YFB3705300)the National Natural Science Foundation of China(Grant Nos.52104380 and 52171123)for grant and financial support.
文摘As a representative of the third generation advanced high-strength steels(AHSSs),medium Mn steels(MMS)have broad development prospects in the field of automobile manufacturing.MMS with typical austenite reversion treatment have a soft duplex microstructure,i.e.ferrite+austenite,presenting a high ductility but a low yield strength.Here we show that a flash heating and cooling after austenite reversion treatment can replace the ferrite with strong martensite,which greatly enhances the yield strength of a 0.25C-4Mn steel by about 461–886 MPa.By adjusting the reversion temperature before the flash treatment,the C and Mn concentrations of reverted austenite can be altered,which determine the fraction of reverted austenite surviving the flash treatment.In addition,the mechanical stability of final retained austenite is also linked to the reversion temperature,resulting different work hardening behaviors due to transformation induced plasticity(TRIP)effect.By tweaking the reversion temperature before the flash treatment,an optimized combination of strength and ductility can be achieved.The micromechanical differences caused by the replacement of the matrix are also investigated via in-situ digital image correlation method.
基金financially supported by the National Natural Science Foundation of China(Grant No.51722402)by the Fundamental Research Funds for the Central Universities(Grant No.2007012)+1 种基金111 Project(No.B16009)the Liaoning Revitalization Talents Program(No.XLYC1907128)。
文摘The martensitic hot-rolled 0.3 C-6 Mn-1.5 Si(wt%)steel was annealed at 630℃for 24 h to improve its cold rollability,followed by cold rolling and annealing at 670℃for 10 min.The annealing process was designed based on the capacities of industrial batch annealing and continuous annealing lines.A duplex submicron austenite and ferrite microstructure and excellent tensile properties were obtained finally,proved the above process is feasible."Austenite memory"was found in the hot-rolled and annealed sample which restricted recrystallization of lath martensite,leading to lath-shaped morphology of austenite and ferrite grains."Austenite memory"disappeared in the cold-rolled and annealed sample due to austenite random nucleation and ferrite recrystallization,resulting in globular microstructure and refinement of both austenite and ferrite grains.The austenite to martensite transformation contributed most of strain hardening during deformation and improved the uniform elongation,but the dislocation strengthening played a decisive role on the yielding behavior.The tensile curves change from continuous to discontinuous yielding as the increase of cold-rolled reduction due to the weakening dislocation strengthening of austenite and ferrite grains related to the morphology change and grain refinement.A method by controlling the cold-rolled reduction is proposed to avoid the Lüders strain.
基金Item Sponsored by Youth Science Funds of China(51101036)National Basic Research Program of China(2010CB630803)National Key Technology Support Program of China(2013BAE07B05)
文摘Both microstrueture and mechanical properties of low alloy steels treated by quenching and partitioning （Q＆P） process were examined. The mixed microstructure of martensite and large-fractioned retained austenite （about 27.3%） was characterized and analyzed, excellent combinations of total elongation of 19% and tensile strength of 1 835 MPa were obtained, and three-stage work hardening behavior was demonstrated during tensile test. The en hanced mechanical properties and work hardening behavior were explained based on the transformation induced plas ticity effect of large fractioned austenite.
基金the Centre for High Performance Steel at Lulea University of Technology for the financial support
文摘High-Si spring steel was heat treated in three different ways： Quenching and tempering at 460 ℃ to obtain a tempered martensite microstructure, and austempering at 300 and 350 ℃, respectively, to obtain two different carbide-free bainitic microstructures. In the steel austempered at 350 ℃, both the bainite lath thickness and retained austenite content were higher than those of the steel austempered at 300 ℃. Rotating-bending fatigue tests were done in order to evaluate the effect of each heat treatment on the high-cycle fatigue behavior of the steel. When the austempering temperature was 300 ℃, the endurance limit was increased by 25% despite a 5% reduction in tensile strength when compared with that of the quenched and tempered steel. The relationship between endurance limit [Rfat （50~）] and ultimate tensile strength （Rm） was higher for the austempered samples in comparison with that of the quenched and tempered material. Therefore, it is believed that the presence of retained austenite affects the relationship between endurance limit and tensile strength.
基金funded by the National Natural Science Foundation of China (No. 50771019)Specialized Research Fund for the Doctoral Program of Higher Education (No. 20090006110013)
文摘Strain-induced martensites in high manganese TRIP/TWIP steels were investigated in the presence of thermal martensites and under the influence of austenitic grain orientation by X-ray diffraction （XRD）, scanning electron microscopy （SEM） and electron backscattered diffraction （EBSD）. Before deformation, the morphology of α＇- M depended mainly on the number of variants and growing period. Regardless of martensite morphologies and deformation, the Kurdjumov-Sachs （K-S） orientation relationships always maintained. The 6 α＇-M variants formed from a plate of ε-M were of 3 pairs of twins with a common axis 〈110〉α＇ parallel to the normal of {112}γ habit plane to minimize transformation strain. When α＇-M could be formed only by deformation, it nucleated at the intersection of ε-M variants and grew mainly in thick ε-M plates. Thick ε plates promoted significantly the α＇-M and weakened the influence of grain orientations. During tension, the transformation in 〈100〉-oriented grains was observed to be slower than that in 〈121〉-oriented grains. Deformation twins promoted ε-M formation slightly and had no apparent effect on α＇-M. Deformation increased the number of ε-M variants, but reduced that of α＇-M variants.
基金supported by the National Natural Science Foundation of China(Nos.52271004 and 51901021).
文摘Enhancing the ductility and toughness of advanced high-strength steels is essential for the wide range of promising applications.The retained austenite(RA)is a key phase due to the austenite-to-martensite transformation and its transformation-induced plasticity effect.It is commonly accepted that slow RA-to-martensite transformation is beneficial to ductility;therefore,the RA fraction and stability should be carefully controlled.The RA stability is related to its morphology,size,carbon content,neighboring phase and orientation.Importantly,these factors are cross-influenced.It is noteworthy that the influence of RA on ductility and fracture toughness is not consistent because of their difference in stress state.There is no clear relationship between fracture toughness and tensile properties.Thus,it is important to understand the role of RA in toughness.The toughness is enhanced during the RA-to-martensite transformation,while the fracture toughness is decreased due to the formation of fresh and brittle martensite.As a result,the findings regarding to the effect of RA on fracture toughness are conflicting.Further investigations should be conducted in order to fully understand the effects of RA on ductility and fracture toughness,which can optimize the combination of ductility and toughness in AHSSs.
基金support from the Steel Joint Funds of the National Natural Science Foundation of China(Grant No.U1560204)Research Grants Council of Hong Kong(Grant Nos.HKU719712E,HKU712713E)Small Project Funding of HKU(Grant No.201409176053)
文摘The Luders deformation behavior in a medium Mn transformation induced plasticity （TRIP） steel is investigated at different temperatures ranging from 25 to 300 ℃. It demonstrates that the Ltiders band appears at all testing temperatures but with varied Luders strains which do not change monoton ically with temperature. The martensitic transformation is simultaneously observed within the Ltiders band in varying degrees depending on the testing temperature. It is well verified that the martensitic transformation is not responsible for the formation of Luders band, and a reasonable explanation is given for the non-monotonic variation of Luders strain with increasing temperature.
基金Z.G.Yang acknowledges financial support from the National Key R&D program of China(grant No.2022YFB3705200)National Natural Science Foundation of China(grant No.52171008)+2 种基金H.Chen acknowledges financial support from the National Natural Science Foundation of China(grant No.51922054)Tsinghua University Initiative Scientific Research Program(No.20233080002)the Mobility Programme from the Sino-German Center(Grant No.M-0319).
文摘Nanoprecipitates and nanoscale retained austenite(RA)with suitable stability play crucial roles in deter-mining the yield strength(YS)and ductility of ultrahigh strength steels(UHSSs).However,owing to the kinetics incompatibility between nanoprecipitation and austenite reversion,it is highly challenging to si-multaneously introduce high-density nanoprecipitates and optimized RA in UHSSs.In this work,through the combination of austenite reversion treatment(ART)and subsequent flash austenitizing(FA),nanoscale chemical heterogeneity was successfully introduced into a low-cost UHSS prior to the aging process.This chemical heterogeneity involved the enrichment of Mn and Ni in the austenite phase.The resulting UHSS exhibited dual-nanoprecipitation of Ni(Al,Mn)and(Mo,Cr)_(2)C and nanoscale austenite stabilized via Mn and Ni enrichment.The hard martensitic matrix strengthened by high-density dual-nanoprecipitates con-strains the plastic deformation of soft RA with a relatively low fraction of-15%,and the presence of relatively stable nanoscale RA with adequate Mn and Ni enrichment leads to a marginal loss in YS but keeps a persistent transformation-induced plasticity(TRIP)effect.As a result,the newly-developed UHSS exhibits an ultrahigh YS of-1.7 GPa,an ultimate tensile strength(UTS)of-1.8 GPa,a large uniform elongation(UE)of-8.5%,and a total elongation(TE)of-13%.The strategy of presetting chemical heterogeneity to introduce proper metastable phases before aging can be extended to other UHSSs and precipitation-hardened alloys.
