Marine thin plates are susceptible to welding deformation owing to their low structural stiffness.Therefore,the efficient and accurate prediction of welding deformation is essential for improving welding quality.The t...Marine thin plates are susceptible to welding deformation owing to their low structural stiffness.Therefore,the efficient and accurate prediction of welding deformation is essential for improving welding quality.The traditional thermal elastic-plastic finite element method(TEP-FEM)can accurately predict welding deformation.However,its efficiency is low because of the complex nonlinear transient computation,making it difficult to meet the needs of rapid engineering evaluation.To address this challenge,this study proposes an efficient prediction method for welding deformation in marine thin plate butt welds.This method is based on the coupled temperature gradient-thermal strain method(TG-TSM)that integrates inherent strain theory with a shell element finite element model.The proposed method first extracts the distribution pattern and characteristic value of welding-induced inherent strain through TEP-FEM analysis.This strain is then converted into the equivalent thermal load applied to the shell element model for rapid computation.The proposed method-particularly,the gradual temperature gradient-thermal strain method(GTG-TSM)-achieved improved computational efficiency and consistent precision.Furthermore,the proposed method required much less computation time than the traditional TEP-FEM.Thus,this study lays the foundation for future prediction of welding deformation in more complex marine thin plates.展开更多
Wire arc additive manufacturing(WAAM)has emerged as a promising approach for fabricating large-scale components.However,conventional WAAM still faces challenges in optimizing microstructural evolution,minimizing addit...Wire arc additive manufacturing(WAAM)has emerged as a promising approach for fabricating large-scale components.However,conventional WAAM still faces challenges in optimizing microstructural evolution,minimizing additive-induced defects,and alleviating residual stress and deformation,all of which are critical for enhancing the mechanical performance of the manufactured parts.Integrating interlayer friction stir processing(FSP)into WAAM significantly enhances the quality of deposited materials.However,numerical simulation research focusing on elucidating the associated thermomechanical coupling mechanisms remains insufficient.A comprehensive numerical model was developed to simulate the thermomechanical coupling behavior in friction stir-assisted WAAM.The influence of post-deposition FSP on the coupled thermomechanical response of the WAAM process was analyzed quantitatively.Moreover,the residual stress distribution and deformation behavior under both single-layer and multilayer deposition conditions were investigated.Thermal analysis of different deposition layers in WAAM and friction stir-assisted WAAM was conducted.Results show that subsequent layer deposition induces partial remelting of the previously solidified layer,whereas FSP does not cause such remelting.Furthermore,thermal stress and deformation analysis confirm that interlayer FSP effectively mitigates residual stresses and distortion in WAAM components,thereby improving their structural integrity and mechanical properties.展开更多
Ice crystal icing is an important cause of accidents in aircraft engines.Ice formation in aircraft engines can cause internal blades to freeze,affecting the quality of the air flow field and blocking the flow path.On ...Ice crystal icing is an important cause of accidents in aircraft engines.Ice formation in aircraft engines can cause internal blades to freeze,affecting the quality of the air flow field and blocking the flow path.On the other hand,the entry of ice crystal particles into the combustion chamber can cause a decrease in temperature or even flameout,leading to engine surge or shutdown.Therefore,it is necessary to conduct multiphase flow tests on ice crystals for aircraft components such as aircraft engines.Conducting ice crystal multiphase flow tests on aircraft is an effective research method,but it requires the construction of an ice crystal multiphase flow test platform that meets relevant technical requirements.The paper focuses on the relevant experimental requirements and combines wind tunnel test structures to conduct multiphase flow numerical simulations on various forms of jet pipelines,obtaining particle motion distribution results.After comparison,the optimal form of jet structure is obtained,providing the best selection scheme for the design of relevant wind tunnel structures.展开更多
Centrifugal casting of ductile iron pipe is a high-temperature,semi-continuous production process.However,conducting laboratory research on the solidification process of centrifugal casting of ductile iron pipe presen...Centrifugal casting of ductile iron pipe is a high-temperature,semi-continuous production process.However,conducting laboratory research on the solidification process of centrifugal casting of ductile iron pipe presents significant challenges.In this study,a novel research method was introduced for investigating the solidification process of ductile iron pipe,namely thermal simulation of ductile iron pipe.Comparative research was conducted on the microstructure and properties of the thermal simulation sample and the ductile iron pipe.The findings indicate that the thermal simulation sample and ductile iron pipe exhibit good heat transfer similarity and microstructure similarity.The difference of cooling rate between thermal simulation sample and ductile pipe is less than 0.24℃·s^(-1),and the difference of microstructure content of free cementite,ferrite,and pearlite is less than 5%.The tensile strength of annealed ductile iron pipe is 466 MPa,with an elongation of 16.1%and a Brinell hardness of 156.5 HBW.In comparison,the tensile strength of annealed thermal simulation sample is 482.0 MPa,with an elongation of 15.5%and a Brinell hardness of 159.0 HBW.These results suggest that the thermal simulation experimental research method is both scientific and feasible,offering an objective,reliable,and cost-effective approach to laboratory research on ductile iron pipe.展开更多
Hydraulic fracturing serves as a critical technology for reservoir stimulation in deep coalbed methane(CBM)development,where the mechanical properties of gangue layers exert a significant control on fracture propagati...Hydraulic fracturing serves as a critical technology for reservoir stimulation in deep coalbed methane(CBM)development,where the mechanical properties of gangue layers exert a significant control on fracture propagation behavior.To address the unclear mechanisms governing fracture penetration across coal-gangue interfaces,this study employs the Continuum-Discontinuum Element Method(CDEM)to simulate and analyze the vertical propagation of hydraulic fractures initiating within coal seams,based on geomechanical parameters derived from the deep Benxi Formation coal seams in the southeastern Ordos Basin.The investigation systematically examines the influence of geological and operational parameters on cross-interfacial fracture growth.Results demonstrate that vertical stress difference,elastic modulus contrast between coal and gangue layers,interfacial stress differential,and interfacial cohesion at coal-gangue interfaces are critical factors governing hydraulic fracture penetration through these interfaces.High vertical stress differences(>3 MPa)inhibit interfacial dilation,promoting predominant crosslayer fracture propagation.Reduced interfacial stress contrasts and enhanced interfacial cohesion facilitate fracture penetration across interfaces.Furthermore,smaller elastic modulus contrasts between coal and gangue correlate with increased interfacial aperture.Finally,lower injection rates effectively suppress vertical fracture propagation in deep coal reservoirs.This study elucidates the characteristics and mechanisms governing cross-layer fracture propagation in coal–rock composites with interbedded partings,and delineates the dynamic evolution laws and dominant controlling factors involved.Thefindings provide critical theoretical insights for the optimization of fracture design and the efficient development of deep coalbed methane reservoirs.展开更多
Energy shortage has become one of themost concerning issues in the world today,and improving energy utilization efficiency is a key area of research for experts and scholars worldwide.Small-diameter heat exchangers of...Energy shortage has become one of themost concerning issues in the world today,and improving energy utilization efficiency is a key area of research for experts and scholars worldwide.Small-diameter heat exchangers offer advantages such as reduced material usage,lower refrigerant charge,and compact structure.However,they also face challenges,including increased refrigerant pressure drop and smaller heat transfer area inside the tubes.This paper combines the advantages and disadvantages of both small and large-diameter tubes and proposes a combined-diameter heat exchanger,consisting of large and small diameters,for use in the indoor units of split-type air conditioners.There are relatively few studies in this area.In this paper,A theoretical and numerical computation method is employed to establish a theoretical-numerical calculation model,and its reliability is verified through experiments.Using this model,the optimal combined diameters and flow path design for a combined-diameter heat exchanger using R32 as the working fluid are derived.The results show that the heat transfer performance of all combined diameter configurations improves by 2.79%to 8.26%compared to the baseline design,with the coefficient of performance(COP)increasing from 4.15 to 4.27~4.5.These designs can save copper material,but at the cost of an increase in pressure drop by 66.86%to 131.84%.The scheme IIIH,using R32,is the optimal combined-diameter and flow path configuration that balances both heat transfer performance and economic cost.展开更多
The Trombe Wall(TW)is a low-cost,passive heating system known for its high thermal efficiency,particularly in cold and temperate climates.Recent research has explored its adaptability to warm-dry climates with high th...The Trombe Wall(TW)is a low-cost,passive heating system known for its high thermal efficiency,particularly in cold and temperate climates.Recent research has explored its adaptability to warm-dry climates with high thermal variability,such as those found in central Mexico.This study presents a dynamic simulation-based analysis of the TW’s thermal performance in a representative social housing unit located in Pachuca de Soto,Hidalgo.Two models were compared—one with a south-facing TW system and one without—to evaluate indoor thermal comfort throughout a full annual cycle.The simulations were conducted using OpenStudio and EnergyPlus,integrating detailed climate data and construction parameters.Results indicate significant improvements in interior temperature stability and comfort during winter,with temperature increases of up to 5.1℃ in living areas.The system’s implementation made it possible to attain a new level of average winter indoor temperature of 18.3℃ by using solar energy,up from 14.4℃ without mechanical heating.The introduction of the TW significantly reduces the interior thermal oscillation and enhances the habitability conditions during the winter,with an increase of 167%in the annual number of hours within the thermal comfort range of 18℃–24℃ vs.the base model.Currently,temperature fluctuations inside buildings due to climate change affect the health of users.The system presented in this study reduces these temperature fluctuations to improve quality of life.展开更多
In order to study the indoor thermal environments in university classrooms in Tianjin,a field study and a questionnaire survey for a main teaching building are carried out.First,the thermal sensations of participants ...In order to study the indoor thermal environments in university classrooms in Tianjin,a field study and a questionnaire survey for a main teaching building are carried out.First,the thermal sensations of participants in the typical classrooms are studied by 180 questionnaires.Then,based on the measured data,the temperature changes in the classrooms during a year are simulated by the DeST software.The results show that the indoor thermal environments in the northern classrooms on the first floor are better than those in other classrooms.And the measurement results accord with the simulation results.These results can be used as a reference for the study of the indoor thermal environments in other seasons.展开更多
In this paper the computer code of AUTOUGH2 is used to carry out numerical simulation study on the Wuqing geothermal reservoir for evaluating reservoir performance upon different exploitation schemes.The simulating ca...In this paper the computer code of AUTOUGH2 is used to carry out numerical simulation study on the Wuqing geothermal reservoir for evaluating reservoir performance upon different exploitation schemes.The simulating calculation and analysis of two main cases,production without reinjection and production with reinjection,were carried out to illuminate and compare the temperature and pressure profiles with distance and time.The water level or pressure will decrease with the time of production,and the reinjection will cause the cooling effect of reinjection on the production zone.展开更多
hi this paper, the non-linear finite element method had been applied to calculate the thermal stress evolving process of the large-scale bearing roller during heating process of final heat treatment. It was found that...hi this paper, the non-linear finite element method had been applied to calculate the thermal stress evolving process of the large-scale bearing roller during heating process of final heat treatment. It was found that two stress peaks appeared during heating process and the second stress peak was higher than the first. If the preheating time was elongated, the second stress peak was reduced distinctly. Therefore, the pre-heating time should be elongated suitably to ensure safety in the practical manufacture process.展开更多
The Kaerqueka polymetallic deposit, Qinghai, China, is one of the typical skarn-type polymetallic ore deposits in the Qimantage metallogenic belt. The dynamic mechanism on the formation of the Kaerqueka polymetallic d...The Kaerqueka polymetallic deposit, Qinghai, China, is one of the typical skarn-type polymetallic ore deposits in the Qimantage metallogenic belt. The dynamic mechanism on the formation of the Kaerqueka polymetallic deposit is always an interesting topic of research. We used the finite difference method to model the mineralizing process of the chalcopyrite in this region with considering the field geological features, mineralogy and geochemistry. In particular, the modern mineralization theory was used to quantitatively estimate the related chemical reactions associated with the chalcopyrite formation in the Kaerqueka polymetallic deposit. The numerical results indicate that the hydrothermal fluid flow is a key controlling factor of mineralization in this area and the temperature gradient is the driving force of pore-fluid flow. The metallogenic temperature of chalcopyrite in the Kaerqueka polymetallic deposit is between 250 and 350 ℃. The corresponding computational results have been verified by the field observations. It has been further demonstrated that the simulation results of coupled models in the field of emerging computational geosciences can enhance our understanding of the ore-forming processes in this area.展开更多
To decrease thermal stress during laser metal deposition shaping(LMDS)process,it is of great importance to learn the transient thermal stress distribution regularities.Based on the“element life and death”technique o...To decrease thermal stress during laser metal deposition shaping(LMDS)process,it is of great importance to learn the transient thermal stress distribution regularities.Based on the“element life and death”technique of finite element analy-sis(FEA),a three-dimensional multi-track and multi-layer numerical simulation model for LMDS is developed with ANSYS parametric design language(APDL)for the first time,in which long-edge parallel reciprocating scanning paths is introduced.Through the model,detailed simulations of thermal stress during whole metal cladding process are conducted,the generation and distribution regularities of thermal stress are also discussed in detail.Using the same process parameters,the simulation results show good agreement with the features of samples which fabricated by LMDS.展开更多
The asthenosphere upwelled on a large scale in the western Pacific and South China Sea during the Cenozoic, which formed strong upward throughflow and caused the thermal structure to be changed obviously. The mathemat...The asthenosphere upwelled on a large scale in the western Pacific and South China Sea during the Cenozoic, which formed strong upward throughflow and caused the thermal structure to be changed obviously. The mathematical analysis has demonstrated that the upward throughflow velocity may have varied from 3×10^11 to 6×10^12 m/s. From the relationship between the lithospheric thickness and the conductive heat flux, the lithospheric heat flux in the western Pacific should be above 30 mW/m^2, which is consistent with the observed data. The huge low-speed zone within the upper mantle of the marginal sea in the western Pacific reflects that the upper mantle melts partially, flows regionally in the regional stress field, forms the upward heat flux at its bottom, and causes the change of the lithospheric thermal structure in the region. The numerical simulation result of the expansion and evolution in the South China Sea has demonstrated that in the early expansion, the upward throughflow velocity was relatively fast, and the effect that it had on the thickness of the lithosphere was relatively great,resulting in the mid-ocean basin expanding rapidly. After the formation of the ocean basin in the South China Sea, the upward throughflow velocity decreased, but the conductive heat flux was relatively high, which is close to the actual situation. Therefore, from the heat transfer point of view, this article discusses how the upward heat flux affects the lithospheric thermal structure in the western Pacific and South China Sea. The conclusions show that the upward heat throughflow at the bottom of the lithospheric mantle resulted in the tectonic deformation at the shallow crust. The intensive uplifts and rifts at the crust led to the continent cracks and the expansion in the South China Sea.展开更多
This paper briefly introduces the current state in computer modelling of geothermal reservoir system and then focuses on our research efforts in high performance simulation of enhanced geothermal reservoir system. A n...This paper briefly introduces the current state in computer modelling of geothermal reservoir system and then focuses on our research efforts in high performance simulation of enhanced geothermal reservoir system. A novel supercomputer simulation tool has been developing towards simulating the highly non-linear coupled geomechanical-fiuid flow-thermal systems involving heterogeneously fractured geomaterials at different spatial and temporal scales. It is applied here to simulate and visualise the enhanced geothermal system （EGS）, such as （1） visualisation of the microseismic events to monitor and determine where/how the underground rupture proceeds during a hydraulic stimulation, to generate the mesh using the recorded data for determining the domain of the ruptured zone and to evaluate the material parameters （i.e., the permeability） for the further numerical analysis and evaluation of the enhanced geothermal reservoir; （2） converting the avail- able fractured rock image/fracture data as well as the reservoir geological geometry to suitable meshes/grids and further simulating the fluid flow in the complicated fractures involving the detailed description of fracture dimension and geometry by the lattice Boltzmann method and/or finite element method; （3） interacting fault system simulation to determine the relevant complicated rup- ture process for evaluating the geological setting and the in-situ reservoir properties; （4） coupled thermo-fluid flow analysis of a geothermal reservoir system for an optimised geothermal reservoir design and management. A few of application examples are presented to show its usefulness in simulating the enhanced geothermal reservoir system.展开更多
The mathematical model for the thermal process of billets rolling has beenestablished, including transporting in air and temperature-holding cover, descaling withhigh-pressure water, and the process of rolling and coo...The mathematical model for the thermal process of billets rolling has beenestablished, including transporting in air and temperature-holding cover, descaling withhigh-pressure water, and the process of rolling and cooling in water box. The calculated data by themodel have been compared with the measured data and the results show that the model is right andcreditable. Based on the model, the main thermal characters of rolling line have been simulated andthe influence of all the parameters on the temperature of rolling has been analyzed.展开更多
The dynamic thermal process during double-sided asymmetrical TIG backing welding of large thick plates （ 1 000 mm×700 mm×50 mm） is numerically simulated using MSC. MARC. The effect of arc distance on the t...The dynamic thermal process during double-sided asymmetrical TIG backing welding of large thick plates （ 1 000 mm×700 mm×50 mm） is numerically simulated using MSC. MARC. The effect of arc distance on the thermal cycle in weld zone during double-sided asymmetrical T1G backing welding is investigated. The results show that the workpiece experiences double-peak thermal cycle in double-sided asymmetrical TIG backing welding. On the one hand, the fore arc has the pre- heating effect on the rear pass, and the pre-heating temperature depends on the distance between the double arcs, the heat input of fore arc, and the initial temperature of workpiece. On the other hand, the rear arc has the post-heating effect on the fore pass. The mutual effects of two heat sources decrease with the increase of arc distance.展开更多
Hydrogen displays the potential to partially replace pulverized coal injection(PCI)in the blast furnace,and it can reduce CO_(2)emissions.In this paper,a three-dimensional mathematical model of hydrogen and pulverized...Hydrogen displays the potential to partially replace pulverized coal injection(PCI)in the blast furnace,and it can reduce CO_(2)emissions.In this paper,a three-dimensional mathematical model of hydrogen and pulverized coal co-injection in blast furnace tuyere was established through numerical simulation,and the effect of hydrogen injection and oxygen enrichment interaction on pulverized coal combustion and raceway smelting was investigated.The simulation results indicate that when the coal injection rate decreased from 36 to 30t/h and the hydrogen injection increased from 0 to 3600 m^(3)/h,the CO_(2)emissions decreased from 1860 to 1551 kg/t,which represents a16.6%reduction,and the pulverized coal burnout decreased from 70.1%to 63.7%.The heat released from hydrogen combustion can not only promote the volatilization of pulverized coal but also affect the combustion reaction between volatilization and oxygen,which resulted in a decrease in the temperature at the end of the raceway.Co-injection of hydrogen with PCI increased the wall temperature near the upper half part of the raceway and at the outlet of the tuyere,which required a high cooling efficiency to extend the service life of the blast furnace.The increase in oxygen level compensated for the decreased average temperature in the raceway due to hydrogen injection.The increase in the oxygen content by 3%while maintaining constant hydrogen and PCI injection rates increased the burnout and average raceway temperature by 4.2%and 43 K,respectively.The mole fraction of CO and H_(2) production increased by 0.04 and 0.02,respectively.Burnout can be improved through optimization of the particle size distribution of pulverized coal.展开更多
Deeply buried mountain tunnels are often exposed to the risk of rock bursts,which always cause serious damage to the supporting structures and threaten the safety of the engineers.Due to the limited data available,a s...Deeply buried mountain tunnels are often exposed to the risk of rock bursts,which always cause serious damage to the supporting structures and threaten the safety of the engineers.Due to the limited data available,a suitable approach to predict the rockburst tendency at the preliminary stage becomes very important.In this study,an integrated methodology combining 3D initial stress inversion and rockburst tendency prediction was developed and subsequently applied to a case study of the Sangzhuling Tunnel on the Sichuan–Tibet Railway.The numerical modelling involved inverting the initial stress field using a multiple linear regression method.The tunnel excavation was simulated separately by FDM and DEM,based on a stress boundary condition from the inverted stress field.The comparative analysis demonstrates that the rockburst ratio calculated using DEM(76.70%)exhibits a slight increase compared to FDM(75.38%),and the rockburst location is consistent with the actual situation.This suggests that DEM is more suitable for simulating the stress redistribution during excavation in a jointed rock mass.The numerical simulation combined with the deviatoric stress approach effectively predicts rockburst tendency,meeting the engineering requirements.Despite its limitations,numerical simulation remains a reliable method for predicting rock bursts.展开更多
In the casting process,in order to compensate for the solidification shrinkage to obtain higher dimensional accuracy of the casting,it is often necessary to modify the original design of castings,and a suitable compen...In the casting process,in order to compensate for the solidification shrinkage to obtain higher dimensional accuracy of the casting,it is often necessary to modify the original design of castings,and a suitable compensation method has a decisive impact on the dimensional accuracy of the actual casting.In this study,based on solidification simulation,a design method of reverse deformation is proposed,and two compensation methods,empirical compensation and direct reverse deformation,are implemented.The simulation results show that the empirical compensation method has problems such as difficulty in determining the parameters and satisfaction of both the overall and local accuracy at the same time;while based on the simulation results for each node of the casting,the direct reverse deformation design achieves the design with shape.In addition,the casting model can be optimized through iterative revisions,so that higher dimensional accuracy can be continuously obtained in the subsequent design process.Therefore,the direct reverse deformation design is more accurate and reasonable compared to empirical compensation method.展开更多
Based on a transient temperature distribution of a 45 steel cylinder workpiece during magnetic quenching, which was obtainedby solving the governing equations with nonlinear boundary on the condition of coupling effec...Based on a transient temperature distribution of a 45 steel cylinder workpiece during magnetic quenching, which was obtainedby solving the governing equations with nonlinear boundary on the condition of coupling effects of heat-magnetism. Accordingto the theory of thermal non-elasticity, computational mechanics, ferromagnetism and phase transformation, a new constitutiveequation considering effects of phase transformation is proposed and solved by means of finite element method. The transientthermal stress and residual stress are obtained and the influencing factors on the thermal stress of magnetic field are analyzedand discussed.展开更多
基金Supported by the National Natural Science Foundation of China under Grant No.51975138the High-Tech Ship Scientific Research Project from the Ministry of Industry and Information Technology under Grant No.CJ05N20the National Defense Basic Research Project under Grant No.JCKY2023604C006.
文摘Marine thin plates are susceptible to welding deformation owing to their low structural stiffness.Therefore,the efficient and accurate prediction of welding deformation is essential for improving welding quality.The traditional thermal elastic-plastic finite element method(TEP-FEM)can accurately predict welding deformation.However,its efficiency is low because of the complex nonlinear transient computation,making it difficult to meet the needs of rapid engineering evaluation.To address this challenge,this study proposes an efficient prediction method for welding deformation in marine thin plate butt welds.This method is based on the coupled temperature gradient-thermal strain method(TG-TSM)that integrates inherent strain theory with a shell element finite element model.The proposed method first extracts the distribution pattern and characteristic value of welding-induced inherent strain through TEP-FEM analysis.This strain is then converted into the equivalent thermal load applied to the shell element model for rapid computation.The proposed method-particularly,the gradual temperature gradient-thermal strain method(GTG-TSM)-achieved improved computational efficiency and consistent precision.Furthermore,the proposed method required much less computation time than the traditional TEP-FEM.Thus,this study lays the foundation for future prediction of welding deformation in more complex marine thin plates.
基金National Key Research and Development Program of China(2022YFB4600902)Shandong Provincial Science Foundation for Outstanding Young Scholars(ZR2024YQ020)。
文摘Wire arc additive manufacturing(WAAM)has emerged as a promising approach for fabricating large-scale components.However,conventional WAAM still faces challenges in optimizing microstructural evolution,minimizing additive-induced defects,and alleviating residual stress and deformation,all of which are critical for enhancing the mechanical performance of the manufactured parts.Integrating interlayer friction stir processing(FSP)into WAAM significantly enhances the quality of deposited materials.However,numerical simulation research focusing on elucidating the associated thermomechanical coupling mechanisms remains insufficient.A comprehensive numerical model was developed to simulate the thermomechanical coupling behavior in friction stir-assisted WAAM.The influence of post-deposition FSP on the coupled thermomechanical response of the WAAM process was analyzed quantitatively.Moreover,the residual stress distribution and deformation behavior under both single-layer and multilayer deposition conditions were investigated.Thermal analysis of different deposition layers in WAAM and friction stir-assisted WAAM was conducted.Results show that subsequent layer deposition induces partial remelting of the previously solidified layer,whereas FSP does not cause such remelting.Furthermore,thermal stress and deformation analysis confirm that interlayer FSP effectively mitigates residual stresses and distortion in WAAM components,thereby improving their structural integrity and mechanical properties.
文摘Ice crystal icing is an important cause of accidents in aircraft engines.Ice formation in aircraft engines can cause internal blades to freeze,affecting the quality of the air flow field and blocking the flow path.On the other hand,the entry of ice crystal particles into the combustion chamber can cause a decrease in temperature or even flameout,leading to engine surge or shutdown.Therefore,it is necessary to conduct multiphase flow tests on ice crystals for aircraft components such as aircraft engines.Conducting ice crystal multiphase flow tests on aircraft is an effective research method,but it requires the construction of an ice crystal multiphase flow test platform that meets relevant technical requirements.The paper focuses on the relevant experimental requirements and combines wind tunnel test structures to conduct multiphase flow numerical simulations on various forms of jet pipelines,obtaining particle motion distribution results.After comparison,the optimal form of jet structure is obtained,providing the best selection scheme for the design of relevant wind tunnel structures.
基金financially supported by the National Natural Science Foundation of China(52130109)。
文摘Centrifugal casting of ductile iron pipe is a high-temperature,semi-continuous production process.However,conducting laboratory research on the solidification process of centrifugal casting of ductile iron pipe presents significant challenges.In this study,a novel research method was introduced for investigating the solidification process of ductile iron pipe,namely thermal simulation of ductile iron pipe.Comparative research was conducted on the microstructure and properties of the thermal simulation sample and the ductile iron pipe.The findings indicate that the thermal simulation sample and ductile iron pipe exhibit good heat transfer similarity and microstructure similarity.The difference of cooling rate between thermal simulation sample and ductile pipe is less than 0.24℃·s^(-1),and the difference of microstructure content of free cementite,ferrite,and pearlite is less than 5%.The tensile strength of annealed ductile iron pipe is 466 MPa,with an elongation of 16.1%and a Brinell hardness of 156.5 HBW.In comparison,the tensile strength of annealed thermal simulation sample is 482.0 MPa,with an elongation of 15.5%and a Brinell hardness of 159.0 HBW.These results suggest that the thermal simulation experimental research method is both scientific and feasible,offering an objective,reliable,and cost-effective approach to laboratory research on ductile iron pipe.
文摘Hydraulic fracturing serves as a critical technology for reservoir stimulation in deep coalbed methane(CBM)development,where the mechanical properties of gangue layers exert a significant control on fracture propagation behavior.To address the unclear mechanisms governing fracture penetration across coal-gangue interfaces,this study employs the Continuum-Discontinuum Element Method(CDEM)to simulate and analyze the vertical propagation of hydraulic fractures initiating within coal seams,based on geomechanical parameters derived from the deep Benxi Formation coal seams in the southeastern Ordos Basin.The investigation systematically examines the influence of geological and operational parameters on cross-interfacial fracture growth.Results demonstrate that vertical stress difference,elastic modulus contrast between coal and gangue layers,interfacial stress differential,and interfacial cohesion at coal-gangue interfaces are critical factors governing hydraulic fracture penetration through these interfaces.High vertical stress differences(>3 MPa)inhibit interfacial dilation,promoting predominant crosslayer fracture propagation.Reduced interfacial stress contrasts and enhanced interfacial cohesion facilitate fracture penetration across interfaces.Furthermore,smaller elastic modulus contrasts between coal and gangue correlate with increased interfacial aperture.Finally,lower injection rates effectively suppress vertical fracture propagation in deep coal reservoirs.This study elucidates the characteristics and mechanisms governing cross-layer fracture propagation in coal–rock composites with interbedded partings,and delineates the dynamic evolution laws and dominant controlling factors involved.Thefindings provide critical theoretical insights for the optimization of fracture design and the efficient development of deep coalbed methane reservoirs.
基金supported by Supported by the Scientific Research Foundation for High-Level Talents of Zhoukou Normal University(ZKNUC2024018).
文摘Energy shortage has become one of themost concerning issues in the world today,and improving energy utilization efficiency is a key area of research for experts and scholars worldwide.Small-diameter heat exchangers offer advantages such as reduced material usage,lower refrigerant charge,and compact structure.However,they also face challenges,including increased refrigerant pressure drop and smaller heat transfer area inside the tubes.This paper combines the advantages and disadvantages of both small and large-diameter tubes and proposes a combined-diameter heat exchanger,consisting of large and small diameters,for use in the indoor units of split-type air conditioners.There are relatively few studies in this area.In this paper,A theoretical and numerical computation method is employed to establish a theoretical-numerical calculation model,and its reliability is verified through experiments.Using this model,the optimal combined diameters and flow path design for a combined-diameter heat exchanger using R32 as the working fluid are derived.The results show that the heat transfer performance of all combined diameter configurations improves by 2.79%to 8.26%compared to the baseline design,with the coefficient of performance(COP)increasing from 4.15 to 4.27~4.5.These designs can save copper material,but at the cost of an increase in pressure drop by 66.86%to 131.84%.The scheme IIIH,using R32,is the optimal combined-diameter and flow path configuration that balances both heat transfer performance and economic cost.
文摘The Trombe Wall(TW)is a low-cost,passive heating system known for its high thermal efficiency,particularly in cold and temperate climates.Recent research has explored its adaptability to warm-dry climates with high thermal variability,such as those found in central Mexico.This study presents a dynamic simulation-based analysis of the TW’s thermal performance in a representative social housing unit located in Pachuca de Soto,Hidalgo.Two models were compared—one with a south-facing TW system and one without—to evaluate indoor thermal comfort throughout a full annual cycle.The simulations were conducted using OpenStudio and EnergyPlus,integrating detailed climate data and construction parameters.Results indicate significant improvements in interior temperature stability and comfort during winter,with temperature increases of up to 5.1℃ in living areas.The system’s implementation made it possible to attain a new level of average winter indoor temperature of 18.3℃ by using solar energy,up from 14.4℃ without mechanical heating.The introduction of the TW significantly reduces the interior thermal oscillation and enhances the habitability conditions during the winter,with an increase of 167%in the annual number of hours within the thermal comfort range of 18℃–24℃ vs.the base model.Currently,temperature fluctuations inside buildings due to climate change affect the health of users.The system presented in this study reduces these temperature fluctuations to improve quality of life.
文摘In order to study the indoor thermal environments in university classrooms in Tianjin,a field study and a questionnaire survey for a main teaching building are carried out.First,the thermal sensations of participants in the typical classrooms are studied by 180 questionnaires.Then,based on the measured data,the temperature changes in the classrooms during a year are simulated by the DeST software.The results show that the indoor thermal environments in the northern classrooms on the first floor are better than those in other classrooms.And the measurement results accord with the simulation results.These results can be used as a reference for the study of the indoor thermal environments in other seasons.
文摘In this paper the computer code of AUTOUGH2 is used to carry out numerical simulation study on the Wuqing geothermal reservoir for evaluating reservoir performance upon different exploitation schemes.The simulating calculation and analysis of two main cases,production without reinjection and production with reinjection,were carried out to illuminate and compare the temperature and pressure profiles with distance and time.The water level or pressure will decrease with the time of production,and the reinjection will cause the cooling effect of reinjection on the production zone.
文摘hi this paper, the non-linear finite element method had been applied to calculate the thermal stress evolving process of the large-scale bearing roller during heating process of final heat treatment. It was found that two stress peaks appeared during heating process and the second stress peak was higher than the first. If the preheating time was elongated, the second stress peak was reduced distinctly. Therefore, the pre-heating time should be elongated suitably to ensure safety in the practical manufacture process.
基金Project(2017YFC0601503)supported by the National Key R&D Program of ChinaProjects(41872249,41472302,41772348)supported by the National Natural Science Foundation of China
文摘The Kaerqueka polymetallic deposit, Qinghai, China, is one of the typical skarn-type polymetallic ore deposits in the Qimantage metallogenic belt. The dynamic mechanism on the formation of the Kaerqueka polymetallic deposit is always an interesting topic of research. We used the finite difference method to model the mineralizing process of the chalcopyrite in this region with considering the field geological features, mineralogy and geochemistry. In particular, the modern mineralization theory was used to quantitatively estimate the related chemical reactions associated with the chalcopyrite formation in the Kaerqueka polymetallic deposit. The numerical results indicate that the hydrothermal fluid flow is a key controlling factor of mineralization in this area and the temperature gradient is the driving force of pore-fluid flow. The metallogenic temperature of chalcopyrite in the Kaerqueka polymetallic deposit is between 250 and 350 ℃. The corresponding computational results have been verified by the field observations. It has been further demonstrated that the simulation results of coupled models in the field of emerging computational geosciences can enhance our understanding of the ore-forming processes in this area.
文摘To decrease thermal stress during laser metal deposition shaping(LMDS)process,it is of great importance to learn the transient thermal stress distribution regularities.Based on the“element life and death”technique of finite element analy-sis(FEA),a three-dimensional multi-track and multi-layer numerical simulation model for LMDS is developed with ANSYS parametric design language(APDL)for the first time,in which long-edge parallel reciprocating scanning paths is introduced.Through the model,detailed simulations of thermal stress during whole metal cladding process are conducted,the generation and distribution regularities of thermal stress are also discussed in detail.Using the same process parameters,the simulation results show good agreement with the features of samples which fabricated by LMDS.
基金supported jointly by the Important Direction Project of the CAS Knowledge Innovation Program (Nos. KZCX2-YW-203-01, KZCX2-YW-128-4)the Program of Key Laboratory of Marginal Sea Geology (No. MSGL04-8)
文摘The asthenosphere upwelled on a large scale in the western Pacific and South China Sea during the Cenozoic, which formed strong upward throughflow and caused the thermal structure to be changed obviously. The mathematical analysis has demonstrated that the upward throughflow velocity may have varied from 3×10^11 to 6×10^12 m/s. From the relationship between the lithospheric thickness and the conductive heat flux, the lithospheric heat flux in the western Pacific should be above 30 mW/m^2, which is consistent with the observed data. The huge low-speed zone within the upper mantle of the marginal sea in the western Pacific reflects that the upper mantle melts partially, flows regionally in the regional stress field, forms the upward heat flux at its bottom, and causes the change of the lithospheric thermal structure in the region. The numerical simulation result of the expansion and evolution in the South China Sea has demonstrated that in the early expansion, the upward throughflow velocity was relatively fast, and the effect that it had on the thickness of the lithosphere was relatively great,resulting in the mid-ocean basin expanding rapidly. After the formation of the ocean basin in the South China Sea, the upward throughflow velocity decreased, but the conductive heat flux was relatively high, which is close to the actual situation. Therefore, from the heat transfer point of view, this article discusses how the upward heat flux affects the lithospheric thermal structure in the western Pacific and South China Sea. The conclusions show that the upward heat throughflow at the bottom of the lithospheric mantle resulted in the tectonic deformation at the shallow crust. The intensive uplifts and rifts at the crust led to the continent cracks and the expansion in the South China Sea.
基金the ARC (Nos.LP0560932,DP110103024)the NSFC (Nos.51034003 and 51174210)
文摘This paper briefly introduces the current state in computer modelling of geothermal reservoir system and then focuses on our research efforts in high performance simulation of enhanced geothermal reservoir system. A novel supercomputer simulation tool has been developing towards simulating the highly non-linear coupled geomechanical-fiuid flow-thermal systems involving heterogeneously fractured geomaterials at different spatial and temporal scales. It is applied here to simulate and visualise the enhanced geothermal system （EGS）, such as （1） visualisation of the microseismic events to monitor and determine where/how the underground rupture proceeds during a hydraulic stimulation, to generate the mesh using the recorded data for determining the domain of the ruptured zone and to evaluate the material parameters （i.e., the permeability） for the further numerical analysis and evaluation of the enhanced geothermal reservoir; （2） converting the avail- able fractured rock image/fracture data as well as the reservoir geological geometry to suitable meshes/grids and further simulating the fluid flow in the complicated fractures involving the detailed description of fracture dimension and geometry by the lattice Boltzmann method and/or finite element method; （3） interacting fault system simulation to determine the relevant complicated rup- ture process for evaluating the geological setting and the in-situ reservoir properties; （4） coupled thermo-fluid flow analysis of a geothermal reservoir system for an optimised geothermal reservoir design and management. A few of application examples are presented to show its usefulness in simulating the enhanced geothermal reservoir system.
文摘The mathematical model for the thermal process of billets rolling has beenestablished, including transporting in air and temperature-holding cover, descaling withhigh-pressure water, and the process of rolling and cooling in water box. The calculated data by themodel have been compared with the measured data and the results show that the model is right andcreditable. Based on the model, the main thermal characters of rolling line have been simulated andthe influence of all the parameters on the temperature of rolling has been analyzed.
文摘The dynamic thermal process during double-sided asymmetrical TIG backing welding of large thick plates （ 1 000 mm×700 mm×50 mm） is numerically simulated using MSC. MARC. The effect of arc distance on the thermal cycle in weld zone during double-sided asymmetrical T1G backing welding is investigated. The results show that the workpiece experiences double-peak thermal cycle in double-sided asymmetrical TIG backing welding. On the one hand, the fore arc has the pre- heating effect on the rear pass, and the pre-heating temperature depends on the distance between the double arcs, the heat input of fore arc, and the initial temperature of workpiece. On the other hand, the rear arc has the post-heating effect on the fore pass. The mutual effects of two heat sources decrease with the increase of arc distance.
基金financially supported by the National Natural Science Foundation of China(No.51904026)the Fundamental Research Funds for the Central Universities(No.06500108)。
文摘Hydrogen displays the potential to partially replace pulverized coal injection(PCI)in the blast furnace,and it can reduce CO_(2)emissions.In this paper,a three-dimensional mathematical model of hydrogen and pulverized coal co-injection in blast furnace tuyere was established through numerical simulation,and the effect of hydrogen injection and oxygen enrichment interaction on pulverized coal combustion and raceway smelting was investigated.The simulation results indicate that when the coal injection rate decreased from 36 to 30t/h and the hydrogen injection increased from 0 to 3600 m^(3)/h,the CO_(2)emissions decreased from 1860 to 1551 kg/t,which represents a16.6%reduction,and the pulverized coal burnout decreased from 70.1%to 63.7%.The heat released from hydrogen combustion can not only promote the volatilization of pulverized coal but also affect the combustion reaction between volatilization and oxygen,which resulted in a decrease in the temperature at the end of the raceway.Co-injection of hydrogen with PCI increased the wall temperature near the upper half part of the raceway and at the outlet of the tuyere,which required a high cooling efficiency to extend the service life of the blast furnace.The increase in oxygen level compensated for the decreased average temperature in the raceway due to hydrogen injection.The increase in the oxygen content by 3%while maintaining constant hydrogen and PCI injection rates increased the burnout and average raceway temperature by 4.2%and 43 K,respectively.The mole fraction of CO and H_(2) production increased by 0.04 and 0.02,respectively.Burnout can be improved through optimization of the particle size distribution of pulverized coal.
基金financially supported by the State Key Laboratory of Geohazard Prevention and Geoenvironment Protection(Chengdu University of Technology)(Grant No.SKLGP2020Z007)。
文摘Deeply buried mountain tunnels are often exposed to the risk of rock bursts,which always cause serious damage to the supporting structures and threaten the safety of the engineers.Due to the limited data available,a suitable approach to predict the rockburst tendency at the preliminary stage becomes very important.In this study,an integrated methodology combining 3D initial stress inversion and rockburst tendency prediction was developed and subsequently applied to a case study of the Sangzhuling Tunnel on the Sichuan–Tibet Railway.The numerical modelling involved inverting the initial stress field using a multiple linear regression method.The tunnel excavation was simulated separately by FDM and DEM,based on a stress boundary condition from the inverted stress field.The comparative analysis demonstrates that the rockburst ratio calculated using DEM(76.70%)exhibits a slight increase compared to FDM(75.38%),and the rockburst location is consistent with the actual situation.This suggests that DEM is more suitable for simulating the stress redistribution during excavation in a jointed rock mass.The numerical simulation combined with the deviatoric stress approach effectively predicts rockburst tendency,meeting the engineering requirements.Despite its limitations,numerical simulation remains a reliable method for predicting rock bursts.
基金This study was financially supported by the National Key Research and Development Program of China(No.2020YFB2008302).
文摘In the casting process,in order to compensate for the solidification shrinkage to obtain higher dimensional accuracy of the casting,it is often necessary to modify the original design of castings,and a suitable compensation method has a decisive impact on the dimensional accuracy of the actual casting.In this study,based on solidification simulation,a design method of reverse deformation is proposed,and two compensation methods,empirical compensation and direct reverse deformation,are implemented.The simulation results show that the empirical compensation method has problems such as difficulty in determining the parameters and satisfaction of both the overall and local accuracy at the same time;while based on the simulation results for each node of the casting,the direct reverse deformation design achieves the design with shape.In addition,the casting model can be optimized through iterative revisions,so that higher dimensional accuracy can be continuously obtained in the subsequent design process.Therefore,the direct reverse deformation design is more accurate and reasonable compared to empirical compensation method.
文摘Based on a transient temperature distribution of a 45 steel cylinder workpiece during magnetic quenching, which was obtainedby solving the governing equations with nonlinear boundary on the condition of coupling effects of heat-magnetism. Accordingto the theory of thermal non-elasticity, computational mechanics, ferromagnetism and phase transformation, a new constitutiveequation considering effects of phase transformation is proposed and solved by means of finite element method. The transientthermal stress and residual stress are obtained and the influencing factors on the thermal stress of magnetic field are analyzedand discussed.
