While laser surface texturing(LST)is a promising manufacturing technique for surface functionalization,simultaneously realizing high precision and high efficiency in the LST of complex curved surface is challenging,du...While laser surface texturing(LST)is a promising manufacturing technique for surface functionalization,simultaneously realizing high precision and high efficiency in the LST of complex curved surface is challenging,due to continuously varied geometries of laser-matter incidence.In the present work,we propose a novel manufacturing system of 7-axis on-the-fly LST for complex curved surface,based on the integrated synchronization of 5-axis linkage motion platform with 2-axis galvanometer.Specifically,the algorithm for decomposing spatial texture trajectory on curved surface into low-frequency and high-frequency parts is established,based on which the kinematic model of synchronized 7-axis system is developed to derive the motion of each axis in both 5-axis linkage motion platform and 2-axis galvanometer simultaneously.Subsequently,the synchronized 7-axis LST system is experimentally realized,including the setup of mechanical stages integrated with optical path,the configuration of numerical control unit,and the development of processing software.Finally,case study of 7-axis on-the-fly LST of freeform aluminum surface is performed,and the advantages in terms of processing efficiency and texturing accuracy over 5-axis linkage LST are demonstrated.The correlation of reduced following errors between mechanical stages with the promoted performance of curved surface texturing by the 7-axis on-the-fly LST is further analyzed.Current work provides a feasible solution for establishing the manufacturing system for high performance LST of complex curved surface.展开更多
Leveraging surface texturing to realize significant friction reduction at contact interfaces has emerged as a preferred technique among tribology experts,boosting tribological energy efficiency and sustainability.This...Leveraging surface texturing to realize significant friction reduction at contact interfaces has emerged as a preferred technique among tribology experts,boosting tribological energy efficiency and sustainability.This review systematically demonstrates optimization strategies,advanced manufacturing methods,typical applications,and outlooks of technical challenges toward surface texturing for friction reduction.Firstly,the lubricated contact models of microtextures are introduced.Then,we provide a framework of state-of-the-art research on synergistic friction optimization strategies of microtexture structures,surface treatments,liquid lubricants,and external energy fields.A comparative analysis evaluates the strengths and weaknesses of manufacturing techniques commonly employed for microtextured surfaces.The latest research advancements in microtextures in different application scenarios are highlighted.Finally,the challenges and directions of future research on surface texturing technology are briefly addressed.This review aims to elaborate on the worldwide progress in the optimization,manufacturing,and application of microtexture-enabled friction reduction technologies to promote their practical utilizations.展开更多
The Textile Technology Centre is the pride of Heberlein.State-of-the-art equipment and a team of top experts guarantee the highest standards of support for customers.Heberlein is the leading provider of air interlacin...The Textile Technology Centre is the pride of Heberlein.State-of-the-art equipment and a team of top experts guarantee the highest standards of support for customers.Heberlein is the leading provider of air interlacing and air texturing jets for synthetic continuous filament yarns and its clients enjoy added value in the form of practical help and guidance on textile processes and economic issues,with a special focus on filament yarn applications.展开更多
Ultrasonic vibration-assisted laser surface processing that involves application of vertical ultrasonic vibrations to the Ti-6 Al-4 V alloy substrates while being irradiated with a CO_2 laser was performed for the dev...Ultrasonic vibration-assisted laser surface processing that involves application of vertical ultrasonic vibrations to the Ti-6 Al-4 V alloy substrates while being irradiated with a CO_2 laser was performed for the development of laser melted and textured surfaces with potential applications in biomedical implants.The laser processing resulted in very consistent repeating undulating grooved surfaces, and the undulations were significantly more pronounced in the samples processed with higher ultrasonic power outputs.The phase evolution, studied by x-ray diffraction, confirmed that the laser processing triggered transformation of globular α→ acicular α and martensitic α' as well as increased amounts of retained α phases,which were also reflected in the microscopic analysis. The surface texture developed by laser processing resulted in increased surface wettability with increasing ultrasonic power output. The textured surfaces exhibited marked decrease in coefficients of friction during sliding wear testing performed under simulated body fluid due to lubricant entrainment within the textured grooves. The texturing also resulted in significant reduction in surface contact area during the wear process, which considerably reduced the overall wear rates due to abrasive wear.展开更多
Grid pattern was textured on Ti-6 Al-4 V alloy(TC4)substrate surface by nanosecond laser system.Laser joining of carbon fiber reinforced thermoplastic composite(CFRTP)to TC4 joints were performed,and the effect of tex...Grid pattern was textured on Ti-6 Al-4 V alloy(TC4)substrate surface by nanosecond laser system.Laser joining of carbon fiber reinforced thermoplastic composite(CFRTP)to TC4 joints were performed,and the effect of texture grid depth was investigated.The contact angle of molten CFRTP on textured TC4 surface was measured and the tensile-shear force was tested.The fracture surface and interface morphology were observed.The results indicated that the wettability of molten CFRTP on TC4 surface improved remarkably after laser textured TC4.Shear force of CFRTP/TC4 joints was increased by 156%after laser textured TC4 surface.When the depth of grid was deeper than 100μm,contact angle increased and incomplete filling of molten CFRTP in grid occurred,the shear force thus decreased gradually.Resin-carbon fibers mixture was adhered on the fracture surface of TC4,and the variation tendency of adhesion ratio was consistent with that of shear force.TC4 matrix was exfoliated from substrate and adhered at the fracture surface of CFRTP,indicating stronger mechanical interlocking occurred at the joining interface after laser textured TC4 surface.Beside mechanical interlocking,compound layer consisted of CTi_(0.42)V_(1.58)carburization phase was also confirmed at interface,suggesting that chemical bonding also occurred at the joining interface.展开更多
Titanium alloys are poor in wear resistance and it is not suitable under sliding conditions even with lubrication because ofits severe adhesive wear tendency.The surface modifications through texturing and surface coa...Titanium alloys are poor in wear resistance and it is not suitable under sliding conditions even with lubrication because ofits severe adhesive wear tendency.The surface modifications through texturing and surface coating were used to enhance the surfaceproperties of the titanium alloy substrate.Hard and wear resistant coatings such as TiAlN and AlCrN were applied over texturedtitanium alloy surfaces with chromium as interlayer.To improve the friction and wear resisting performance of hard coatings further,solid lubricant,molybdenum disulphide(MoS2),was deposited on dimples made over hard coatings.Unidirectional sliding weartests were performed with pin on disc contact geometry,to evaluate the tribological performance of coated substrates.The tests wereperformed under three different normal loads for a period of40min at sliding velocity of2m/s.The tribological behaviours ofmulti-layer coatings such as coating structure,friction coefficient and specific wear rate were investigated and analyzed.The lowerfriction coefficient of approximately0.1was found at the early sliding stage,which reduces the material transfer and increases thewear life.Although,the friction coefficient increased to high values after MoS2coating was partially removed,substrate was stillprotected against wear by underlying hard composite layer.展开更多
In this investigation,a picosecond laser was employed to fabricate surface textures on a Stavax steel substrate,which is a key material for mold fabrication in the manufacturing of various polymer products.Three main ...In this investigation,a picosecond laser was employed to fabricate surface textures on a Stavax steel substrate,which is a key material for mold fabrication in the manufacturing of various polymer products.Three main types of surface textures were fabricated on a Stavax steel substrate:periodic ripples,a two-scale hierarchical two-dimensional array of micro-bumps,and a micro-pits array with nanoripples.The wettability of the laser-textured Stavax steel surface was converted from its original hydrophilicity into hydrophobicity and even super-hydrophobicity after exposure to air.The results clearly show that this super-hydrophobicity is mainly due to the surface textures.The ultrafast laserinduced catalytic effect may play a secondary role in modifying the surface chemistry so as to lower the surface energy.The laser-induced surface textures on the metal mold substrates were then replicated onto polypropylene substrates via the polymer injection molding process.The surface wettability of the molded polypropylene was found to be changed from the original hydrophilicity to superhydrophobicity.This developed process holds the potential to improve the performance of fabricated plastic products in terms of wettability control and easy cleaning.展开更多
Tailored surface textures at the micro- or nanoscale dimensions are widely used to get required functional performances. Rotary ultrasonic texturing （RUT） technique has been proved to be capable of fabricating perio...Tailored surface textures at the micro- or nanoscale dimensions are widely used to get required functional performances. Rotary ultrasonic texturing （RUT） technique has been proved to be capable of fabricating periodic micro- and nanostructures. In the present study, diamond tools with geometrically defined cutting edges were designed for fabricating different types of tailored surface textures using the RUT method. Surface generation mechanisms and machinable structures of the RUT process are analyzed and simulated with a 3D-CAD program. Textured surfaces generated by using a triangular pyramid cutting tip are constructed. Different textural patterns from several micrometers to several tens of micrometers with few burrs were successfully fabricated, which proved that tools with a proper two-rake-face design are capable of removing cutting chips efficiently along a sinusoidal cutting locus in the RUT process. Technical applications of the textured surfaces are also discussed. Wetting properties of textured aluminum surfaces were evaluated by combining the test of surface roughness features. The results show that the real surface area of the textured aluminum surfaces almost doubled by comparing with that of a flat surface, and anisotropic wetting properties were obtained due to the obvious directional textural features.展开更多
The cooperative effect of laser surface texturing(LST) and double glow plasma surface alloying on tribological performance of lubricated sliding contacts was investigated.A Nd:YAG laser was used to generate microdimpl...The cooperative effect of laser surface texturing(LST) and double glow plasma surface alloying on tribological performance of lubricated sliding contacts was investigated.A Nd:YAG laser was used to generate microdimples on steel surfaces. Dimples with the diameter of 150μm and the depth of 30-35μm distributed circumferentially on the disc surface.The alloying element Cr was sputtered to the laser texturing steel surface by double glow plasma technique.A deep diffusion layer with a thickness of 30μm and a high hardness of HV900 was formed in this alloy.Tribological experiments of three types of samples(smooth,texturing and texturing+alloying) were conducted with a ring-on-disc tribometer to simulate the face seal.It is found that,in comparison with smooth steel surfaces,the laser texturing samples significantly reduce the friction coefficient.Moreover,the lower wear rate of the sample treated with the two surface techniques is observed.展开更多
The objective of this research is to prepare specially designed surface texture on hard steel surface by electrochemical micromachining (EM) and to incorporate electroless plated Ag/MoS2 solid lubricant coating into t...The objective of this research is to prepare specially designed surface texture on hard steel surface by electrochemical micromachining (EM) and to incorporate electroless plated Ag/MoS2 solid lubricant coating into the dimples of EM textured steel surface to effectively reduce friction and wear of steel-steel contacts. The friction and wear behavior of the Ag/MoS2 solid lubricant coating on EM textured steel surface was evaluated in relation to the size and spacing of the dimples thereon. The microstructure of as-plated Ag/MoS2 solid lubricant coating and the morphology and elemental composition of the worn coating surface and counterface steel surface were analyzed by means of optical microscopy, scanning electron microscopy, and energy dispersive spectrometry. It is found that electroless plated Ag/MoS2 coating is able to greatly reduce the friction and wear of the EM textured steel disc coupled with GCr15 steel ring, mainly because of the formation of solid self-lubricating layer on the EM textured steel surface and of transferred lubricating film on counterface steel surface. The diameter and spacing of the dimples are suggested as 500 μm for acquiring the best wear resistance of the hard steel discs after electrochemical micromachining treatment and electroless plating of Ag/MoS2 solid lubricating coating.展开更多
A pulsed,picosecond Nd:YAG laser with a wavelength of 532 nm is used to texture the surface of grade 5 titanium alloy(Ti–6Al–4V)for minimizing its wear rate.The wear properties of the base samples and laser surface ...A pulsed,picosecond Nd:YAG laser with a wavelength of 532 nm is used to texture the surface of grade 5 titanium alloy(Ti–6Al–4V)for minimizing its wear rate.The wear properties of the base samples and laser surface textured samples are analyzed by conducting wear tests under a sliding condition using pin-on-disk equipment.The wear tests are conducted based on the Box–Benhken design,and the interaction of the process parameters is analyzed using response surface methodology.The wear analysis is conducted by varying the load,rotating speed of the disc,and track diameter at room temperature with a sliding distance of 1500 m.The results demonstrate that the laser textured surfaces exhibited a lower coefficient of friction and good anti-wear properties as compared with the non-textured surfaces.A regression model is developed for the wear analysis of titanium alloy using the analysis of variance technique.It is also observed from the analysis that the applied load and sliding distance are the parameters that have the greatest effect on the wear behavior followed by the wear track diameter.The optimum operating conditions have been suggested based on the results obtained from the numerical optimization approach.展开更多
Due to it being environmentally friendly, much attention has been paid to the dry plasma texturing technique serving as an alternative candidate for multicrystalline silicon （mc-Si） surface texturing. In this paper,...Due to it being environmentally friendly, much attention has been paid to the dry plasma texturing technique serving as an alternative candidate for multicrystalline silicon （mc-Si） surface texturing. In this paper, capacitively coupled plasma （CCP） driven by a dual frequency （DF） of 40.68 MHz and 13.56 MHz is first used for plasma texturing of mc-Si with SF6/O2 gas mixture. Using a hairpin resonant probe and optical emission techniques, DF-CCP characteristics and their influence on mc-silicon surface plasma texturing are investigated at different flow rate ratios, pressures, and radio-frequency （RF） input powers. Experimental results show that suitable plasma texturing of mc-silicon occurs only in a narrow range of plasma parameters, where electron density ne must be larger than 6.3 x 109 cm-3 and the spectral intensity ratio of the F atom to that of the O atom （[F]/[O]） in the plasma must be between 0.8 and 0.3. Out of this range, no cone-like structure is formed on the mc-silicon surface. In our experiments, the lowest reflectance of about 7.3% for mc-silicon surface texturing is obtained at an [F]/[O] of 0.5 and ne of 6.9 × 109 cm-3.展开更多
Self-lubricating composites(SLCs)are widely used in the fields of aerospace and marine,but the conventional NiCr matrix SLCs with sulfide as solid lubricant often suffer from low wear resistance at high temperatures.I...Self-lubricating composites(SLCs)are widely used in the fields of aerospace and marine,but the conventional NiCr matrix SLCs with sulfide as solid lubricant often suffer from low wear resistance at high temperatures.In view of its high affinity with oxygen and also the high oxidation rate,appropriate amount of nano Ti was added to NiCr-WS_(2)composites prepared by spark plasma sintering(SPS)to adjust the oxidation behavior and surface texture.When exposed to high temperature,Ti was preferentially oxidized in comparison to Ni and Cr,resulting in abundant TiO_(2)protrusions and microdimples on the surface,i.e.in situ surface texturing.Besides,TiO_(2)was of high chemical activity and readily to react with other oxide debris during high temperature sliding process to form compounds of NiTiO_(3)and CrTi_(2)O_(5).The high chemical activity of oxide debris that was conducive to sintering,combining with the special surface texture that stores as many wear debris as possible,promoted the rapid formation of a protective glaze layer on the sliding surface.The NiCr-WS_(2)-Ti composite exhibited low friction coefficient but high wear resistance at elevated temperatures.Especially at 800℃,it presented a wear rate of as low as(2.1±0.3)×10^(-5)mm^3N-1m^(-1),accounting for only 2.7%of that of NiCr-WS_(2)composite.展开更多
The lightness and high strength-to-weight ratio of the magnesium alloy have attracted more interest in various applications.However,micro/nanostructure generation on their surfaces remains a challenge due to the flamm...The lightness and high strength-to-weight ratio of the magnesium alloy have attracted more interest in various applications.However,micro/nanostructure generation on their surfaces remains a challenge due to the flammability and ignition.Motivated by this,this study proposed a machining process,named the ultraprecision diamond surface texturing process,to machine the micro/nanostructures on magnesium alloy surfaces.Experimental results showed the various microstructures and sawtooth-shaped nanostructures were successfully generated on the AZ31B magnesium alloy surfaces,demonstrating the effectiveness of this proposed machining process.Furthermore,sawtooth-shaped nanostructures had the function of inducing the optical effect and generating different colors on workpiece surfaces.The colorful letter and colorful flower image were clearly viewed on magnesium alloy surfaces.The corresponding cutting force,chip morphology,and tool wear were systematically investigated to understand the machining mechanism of micro/nanostructures on magnesium alloy surfaces.The proposed machining process can further improve the performances of the magnesium alloy and extend its functions to other fields,such as optics.展开更多
Zirconia(ZrO_2)incorporated ceramic coatings were fabricated on biodegradable ZM21 Mg alloy by the PEO coupled with EPD process.Subsequently,the sample surface was modified by laser texturing to improve the corrosion ...Zirconia(ZrO_2)incorporated ceramic coatings were fabricated on biodegradable ZM21 Mg alloy by the PEO coupled with EPD process.Subsequently,the sample surface was modified by laser texturing to improve the corrosion resistance,roughness and cell proliferation and growth properties.The corrosion performance of the fabricated samples along with the substrate was studied by electrochemical measurements under simulated body fluid(SBF)environment.The cell direct contact assay was conducted for the substrate and fabricated samples using L-929 mouse fibroblast cells for 24 h.The phase contrast images of cell direct contact assay revealed that fabricated samples exhibited better contact and response with the fibroblast cells,compared to the substrate.The addition of nanoparticles in the PEO process,called PEO coupled EPD process,resulted in attaining a higher thickness and improved corrosion performance of the samples than the PEO coated samples.Among all the samples,laser surface textured PEO,and PEO-EPD coated samples unveiled enhanced corrosion resistance,cell growth,thereby enabling it as a suitable prototype for biodegradable implant applications.展开更多
Unique and various microstructures of titanium oxide(TiO_2 ) film including macroporous structure, chromatic veins and rings, have been easily fabricated by mist deposition method on silicon substrate with mild prepar...Unique and various microstructures of titanium oxide(TiO_2 ) film including macroporous structure, chromatic veins and rings, have been easily fabricated by mist deposition method on silicon substrate with mild preparation conditions. Rutile phase TiO_2 nanoparticles were directly used as starting material to prepare film and led to a simple preparation process. It was found that several different microstructures existed in the sample and changed with the varied positions from the center to the edge of the film when the concentration of the TiO_2 suspension is 0.06 mol/l, the deposition time is 30 min, the flow rate is 1 l/min and the temperature is150. The surface texturing shows apparent distinction as the concentration of the TiO_2 suspension decreased to 0.03 mol/l and 0.01 mol/l.展开更多
The contact fatigue life of machine elements is affected by pitting, wear and so on, under heavier loading conditions. Increasing the fatigue life requires mainly the improvements of lubricating condition, operating c...The contact fatigue life of machine elements is affected by pitting, wear and so on, under heavier loading conditions. Increasing the fatigue life requires mainly the improvements of lubricating condition, operating condition and materials. In order to improve the lubricating condition, it is necessary to investigate the relation of the microscopic surface texturing and the contact modes of machine elements. In this paper, thus, the pressure and oil film thickness of the contact between sphere and the plate with 5 kinds surface texturing were calculated using a commercial software based on Reynolds equation. There was sufficient evidence to suggest that the dimple shape was the optimum texturing to increase the lubricating condition.展开更多
The relationship between the structure of PP drawn filament and the crimp elasticity of tex-tured yarn is investigated.It is found that orientation,crystallinity,and especially,crystalline formof drawn filament are re...The relationship between the structure of PP drawn filament and the crimp elasticity of tex-tured yarn is investigated.It is found that orientation,crystallinity,and especially,crystalline formof drawn filament are related to crimp property of textured yarn.Lower crystallinity,moderateorientation and unstable para-crystalline structure are necessary for increasing crimp elasticity.Inaddition,the filament structure and properties before and after texturing are compared.展开更多
An isotropic etching technique of texturing silicon solar cells has been applied to polycrystalline silicon wafers with different acid concentrations. Optimal e tching conditions have been determined by etching rate c...An isotropic etching technique of texturing silicon solar cells has been applied to polycrystalline silicon wafers with different acid concentrations. Optimal e tching conditions have been determined by etching rate calculation, scanning ele ctron microscope (SEM) image and reflectance measurement. The surface morphology of the textured wafers varies in accordance with the different etchant concentr ation which in turn leads to the dissimilarity of etching speed. Textured polycr ystalline silicon wafer surfaces display randomly located etched pits which can reduce the surface reflection and enhance the light absorption. The special rela tionship between reflectivity and etching rate was studied. Reflectance measurem ents show that isotropic texturing is one of the suitable techniques for texturi ng polycrystalline silicon wafers and benefits solar cells performances.展开更多
This study presents a comprehensive approach to applying texturing processes created by engraving on the surface of CoCr28Mo alloy workpieces using a 20 W pulsed nanosecond fiber laser.The hatch strategy and distance,...This study presents a comprehensive approach to applying texturing processes created by engraving on the surface of CoCr28Mo alloy workpieces using a 20 W pulsed nanosecond fiber laser.The hatch strategy and distance,frequency,and scan speed were control parameters for texturing applications.The effectiveness of the parameters in terms of roughness and contact angle of the texturized surface was investigated.Surface roughness and contact angle were analyzed using variance analysis to identify each variable's influence.It has been determined that the roughness of the texture defined by the hatch strategy plays a decisive role in the wettability behavior of the surface;however,the scan speed,frequency,and hatch distance which are among the laser surface texturing conditions are influential in the roughness and contact angle.Increasing scan speed and hatch distance while decreasing frequency resulted in smoother surfaces,increasing the contact angle.Textures having rough surfaces produced with different processing conditions exhibit a super hydrophilic behavior.The contact angle is most sensitive to the hatch distance;however,the frequency has the least influence on the contact angle.The most and least efficient surface roughness parameters are revealed to be scan speed and hatch distance,respectively.展开更多
基金the support by the Harbin Manufacturing Science and Technology Innovation Talent Project(No.2023CXRCGD035)the Open Research Foundation of State Key Laboratory of Digital Manufacturing Equipment and Technology in Huazhong University of Science and Technology,China(No.IMETKF2023012).
文摘While laser surface texturing(LST)is a promising manufacturing technique for surface functionalization,simultaneously realizing high precision and high efficiency in the LST of complex curved surface is challenging,due to continuously varied geometries of laser-matter incidence.In the present work,we propose a novel manufacturing system of 7-axis on-the-fly LST for complex curved surface,based on the integrated synchronization of 5-axis linkage motion platform with 2-axis galvanometer.Specifically,the algorithm for decomposing spatial texture trajectory on curved surface into low-frequency and high-frequency parts is established,based on which the kinematic model of synchronized 7-axis system is developed to derive the motion of each axis in both 5-axis linkage motion platform and 2-axis galvanometer simultaneously.Subsequently,the synchronized 7-axis LST system is experimentally realized,including the setup of mechanical stages integrated with optical path,the configuration of numerical control unit,and the development of processing software.Finally,case study of 7-axis on-the-fly LST of freeform aluminum surface is performed,and the advantages in terms of processing efficiency and texturing accuracy over 5-axis linkage LST are demonstrated.The correlation of reduced following errors between mechanical stages with the promoted performance of curved surface texturing by the 7-axis on-the-fly LST is further analyzed.Current work provides a feasible solution for establishing the manufacturing system for high performance LST of complex curved surface.
基金the National Natural Science Foundation of China(Award No.07120016)support by the Dalian University of Technology(DUT)(Award Nos.82232022,82232043,and DUT22LAB404)AVIC Shenyang Aircraft Company(Award No.12020641 and 12020642)。
文摘Leveraging surface texturing to realize significant friction reduction at contact interfaces has emerged as a preferred technique among tribology experts,boosting tribological energy efficiency and sustainability.This review systematically demonstrates optimization strategies,advanced manufacturing methods,typical applications,and outlooks of technical challenges toward surface texturing for friction reduction.Firstly,the lubricated contact models of microtextures are introduced.Then,we provide a framework of state-of-the-art research on synergistic friction optimization strategies of microtexture structures,surface treatments,liquid lubricants,and external energy fields.A comparative analysis evaluates the strengths and weaknesses of manufacturing techniques commonly employed for microtextured surfaces.The latest research advancements in microtextures in different application scenarios are highlighted.Finally,the challenges and directions of future research on surface texturing technology are briefly addressed.This review aims to elaborate on the worldwide progress in the optimization,manufacturing,and application of microtexture-enabled friction reduction technologies to promote their practical utilizations.
文摘The Textile Technology Centre is the pride of Heberlein.State-of-the-art equipment and a team of top experts guarantee the highest standards of support for customers.Heberlein is the leading provider of air interlacing and air texturing jets for synthetic continuous filament yarns and its clients enjoy added value in the form of practical help and guidance on textile processes and economic issues,with a special focus on filament yarn applications.
基金supported by the U.S. National Science Foundation (NSF CAREER Award No. CMMI-1149079)
文摘Ultrasonic vibration-assisted laser surface processing that involves application of vertical ultrasonic vibrations to the Ti-6 Al-4 V alloy substrates while being irradiated with a CO_2 laser was performed for the development of laser melted and textured surfaces with potential applications in biomedical implants.The laser processing resulted in very consistent repeating undulating grooved surfaces, and the undulations were significantly more pronounced in the samples processed with higher ultrasonic power outputs.The phase evolution, studied by x-ray diffraction, confirmed that the laser processing triggered transformation of globular α→ acicular α and martensitic α' as well as increased amounts of retained α phases,which were also reflected in the microscopic analysis. The surface texture developed by laser processing resulted in increased surface wettability with increasing ultrasonic power output. The textured surfaces exhibited marked decrease in coefficients of friction during sliding wear testing performed under simulated body fluid due to lubricant entrainment within the textured grooves. The texturing also resulted in significant reduction in surface contact area during the wear process, which considerably reduced the overall wear rates due to abrasive wear.
基金financially supported by National Natural Science Foundation of China(No.51875129)。
文摘Grid pattern was textured on Ti-6 Al-4 V alloy(TC4)substrate surface by nanosecond laser system.Laser joining of carbon fiber reinforced thermoplastic composite(CFRTP)to TC4 joints were performed,and the effect of texture grid depth was investigated.The contact angle of molten CFRTP on textured TC4 surface was measured and the tensile-shear force was tested.The fracture surface and interface morphology were observed.The results indicated that the wettability of molten CFRTP on TC4 surface improved remarkably after laser textured TC4.Shear force of CFRTP/TC4 joints was increased by 156%after laser textured TC4 surface.When the depth of grid was deeper than 100μm,contact angle increased and incomplete filling of molten CFRTP in grid occurred,the shear force thus decreased gradually.Resin-carbon fibers mixture was adhered on the fracture surface of TC4,and the variation tendency of adhesion ratio was consistent with that of shear force.TC4 matrix was exfoliated from substrate and adhered at the fracture surface of CFRTP,indicating stronger mechanical interlocking occurred at the joining interface after laser textured TC4 surface.Beside mechanical interlocking,compound layer consisted of CTi_(0.42)V_(1.58)carburization phase was also confirmed at interface,suggesting that chemical bonding also occurred at the joining interface.
文摘Titanium alloys are poor in wear resistance and it is not suitable under sliding conditions even with lubrication because ofits severe adhesive wear tendency.The surface modifications through texturing and surface coating were used to enhance the surfaceproperties of the titanium alloy substrate.Hard and wear resistant coatings such as TiAlN and AlCrN were applied over texturedtitanium alloy surfaces with chromium as interlayer.To improve the friction and wear resisting performance of hard coatings further,solid lubricant,molybdenum disulphide(MoS2),was deposited on dimples made over hard coatings.Unidirectional sliding weartests were performed with pin on disc contact geometry,to evaluate the tribological performance of coated substrates.The tests wereperformed under three different normal loads for a period of40min at sliding velocity of2m/s.The tribological behaviours ofmulti-layer coatings such as coating structure,friction coefficient and specific wear rate were investigated and analyzed.The lowerfriction coefficient of approximately0.1was found at the early sliding stage,which reduces the material transfer and increases thewear life.Although,the friction coefficient increased to high values after MoS2coating was partially removed,substrate was stillprotected against wear by underlying hard composite layer.
基金the Agency for Science Technology and Research (A*STAR) of Singapore for financial support
文摘In this investigation,a picosecond laser was employed to fabricate surface textures on a Stavax steel substrate,which is a key material for mold fabrication in the manufacturing of various polymer products.Three main types of surface textures were fabricated on a Stavax steel substrate:periodic ripples,a two-scale hierarchical two-dimensional array of micro-bumps,and a micro-pits array with nanoripples.The wettability of the laser-textured Stavax steel surface was converted from its original hydrophilicity into hydrophobicity and even super-hydrophobicity after exposure to air.The results clearly show that this super-hydrophobicity is mainly due to the surface textures.The ultrafast laserinduced catalytic effect may play a secondary role in modifying the surface chemistry so as to lower the surface energy.The laser-induced surface textures on the metal mold substrates were then replicated onto polypropylene substrates via the polymer injection molding process.The surface wettability of the molded polypropylene was found to be changed from the original hydrophilicity to superhydrophobicity.This developed process holds the potential to improve the performance of fabricated plastic products in terms of wettability control and easy cleaning.
基金Supported by Japan Society for the Promotion of Science(Grant Nos.14J04115,16K17990)
文摘Tailored surface textures at the micro- or nanoscale dimensions are widely used to get required functional performances. Rotary ultrasonic texturing （RUT） technique has been proved to be capable of fabricating periodic micro- and nanostructures. In the present study, diamond tools with geometrically defined cutting edges were designed for fabricating different types of tailored surface textures using the RUT method. Surface generation mechanisms and machinable structures of the RUT process are analyzed and simulated with a 3D-CAD program. Textured surfaces generated by using a triangular pyramid cutting tip are constructed. Different textural patterns from several micrometers to several tens of micrometers with few burrs were successfully fabricated, which proved that tools with a proper two-rake-face design are capable of removing cutting chips efficiently along a sinusoidal cutting locus in the RUT process. Technical applications of the textured surfaces are also discussed. Wetting properties of textured aluminum surfaces were evaluated by combining the test of surface roughness features. The results show that the real surface area of the textured aluminum surfaces almost doubled by comparing with that of a flat surface, and anisotropic wetting properties were obtained due to the obvious directional textural features.
基金Project(2007046) supported by High Technology Research Project of Jiangsu Province,China
文摘The cooperative effect of laser surface texturing(LST) and double glow plasma surface alloying on tribological performance of lubricated sliding contacts was investigated.A Nd:YAG laser was used to generate microdimples on steel surfaces. Dimples with the diameter of 150μm and the depth of 30-35μm distributed circumferentially on the disc surface.The alloying element Cr was sputtered to the laser texturing steel surface by double glow plasma technique.A deep diffusion layer with a thickness of 30μm and a high hardness of HV900 was formed in this alloy.Tribological experiments of three types of samples(smooth,texturing and texturing+alloying) were conducted with a ring-on-disc tribometer to simulate the face seal.It is found that,in comparison with smooth steel surfaces,the laser texturing samples significantly reduce the friction coefficient.Moreover,the lower wear rate of the sample treated with the two surface techniques is observed.
基金supported by the the National NaturalScience Foundation of China(No.51205001)Foundation for Young Talents in College of Anhui Province(No.2012SQRL083ZD)the Talent Innovation Fund of An-hui Polytechnic University(No.S05305)
文摘The objective of this research is to prepare specially designed surface texture on hard steel surface by electrochemical micromachining (EM) and to incorporate electroless plated Ag/MoS2 solid lubricant coating into the dimples of EM textured steel surface to effectively reduce friction and wear of steel-steel contacts. The friction and wear behavior of the Ag/MoS2 solid lubricant coating on EM textured steel surface was evaluated in relation to the size and spacing of the dimples thereon. The microstructure of as-plated Ag/MoS2 solid lubricant coating and the morphology and elemental composition of the worn coating surface and counterface steel surface were analyzed by means of optical microscopy, scanning electron microscopy, and energy dispersive spectrometry. It is found that electroless plated Ag/MoS2 coating is able to greatly reduce the friction and wear of the EM textured steel disc coupled with GCr15 steel ring, mainly because of the formation of solid self-lubricating layer on the EM textured steel surface and of transferred lubricating film on counterface steel surface. The diameter and spacing of the dimples are suggested as 500 μm for acquiring the best wear resistance of the hard steel discs after electrochemical micromachining treatment and electroless plating of Ag/MoS2 solid lubricating coating.
基金SASTRA University for the valuable help and support provided
文摘A pulsed,picosecond Nd:YAG laser with a wavelength of 532 nm is used to texture the surface of grade 5 titanium alloy(Ti–6Al–4V)for minimizing its wear rate.The wear properties of the base samples and laser surface textured samples are analyzed by conducting wear tests under a sliding condition using pin-on-disk equipment.The wear tests are conducted based on the Box–Benhken design,and the interaction of the process parameters is analyzed using response surface methodology.The wear analysis is conducted by varying the load,rotating speed of the disc,and track diameter at room temperature with a sliding distance of 1500 m.The results demonstrate that the laser textured surfaces exhibited a lower coefficient of friction and good anti-wear properties as compared with the non-textured surfaces.A regression model is developed for the wear analysis of titanium alloy using the analysis of variance technique.It is also observed from the analysis that the applied load and sliding distance are the parameters that have the greatest effect on the wear behavior followed by the wear track diameter.The optimum operating conditions have been suggested based on the results obtained from the numerical optimization approach.
基金supported by the Prospective Project of Industry–University–Research Institution of Jiangsu Province,China(Grant No.BY2010125)the National Natural Science Foundation of China(Grant No.11175127)
文摘Due to it being environmentally friendly, much attention has been paid to the dry plasma texturing technique serving as an alternative candidate for multicrystalline silicon （mc-Si） surface texturing. In this paper, capacitively coupled plasma （CCP） driven by a dual frequency （DF） of 40.68 MHz and 13.56 MHz is first used for plasma texturing of mc-Si with SF6/O2 gas mixture. Using a hairpin resonant probe and optical emission techniques, DF-CCP characteristics and their influence on mc-silicon surface plasma texturing are investigated at different flow rate ratios, pressures, and radio-frequency （RF） input powers. Experimental results show that suitable plasma texturing of mc-silicon occurs only in a narrow range of plasma parameters, where electron density ne must be larger than 6.3 x 109 cm-3 and the spectral intensity ratio of the F atom to that of the O atom （[F]/[O]） in the plasma must be between 0.8 and 0.3. Out of this range, no cone-like structure is formed on the mc-silicon surface. In our experiments, the lowest reflectance of about 7.3% for mc-silicon surface texturing is obtained at an [F]/[O] of 0.5 and ne of 6.9 × 109 cm-3.
基金financially supported by the National Natural Science Foundation of China(No.51871051)。
文摘Self-lubricating composites(SLCs)are widely used in the fields of aerospace and marine,but the conventional NiCr matrix SLCs with sulfide as solid lubricant often suffer from low wear resistance at high temperatures.In view of its high affinity with oxygen and also the high oxidation rate,appropriate amount of nano Ti was added to NiCr-WS_(2)composites prepared by spark plasma sintering(SPS)to adjust the oxidation behavior and surface texture.When exposed to high temperature,Ti was preferentially oxidized in comparison to Ni and Cr,resulting in abundant TiO_(2)protrusions and microdimples on the surface,i.e.in situ surface texturing.Besides,TiO_(2)was of high chemical activity and readily to react with other oxide debris during high temperature sliding process to form compounds of NiTiO_(3)and CrTi_(2)O_(5).The high chemical activity of oxide debris that was conducive to sintering,combining with the special surface texture that stores as many wear debris as possible,promoted the rapid formation of a protective glaze layer on the sliding surface.The NiCr-WS_(2)-Ti composite exhibited low friction coefficient but high wear resistance at elevated temperatures.Especially at 800℃,it presented a wear rate of as low as(2.1±0.3)×10^(-5)mm^3N-1m^(-1),accounting for only 2.7%of that of NiCr-WS_(2)composite.
基金supported by the Special Actions for Developing High-performance Manufacturing of Ministry of Industry and Information Technology(Grant No.:TC200H02J)the Research Grants Council of the Hong Kong Special Ad-ministrative Region,China(Project No.:PolyU 152125/18E)+1 种基金the National Natural Science Foundation of China(Project No.:U19A20104)the Research Committee of The Hong Kong Polytechnic University(Project Code G-RK2V).
文摘The lightness and high strength-to-weight ratio of the magnesium alloy have attracted more interest in various applications.However,micro/nanostructure generation on their surfaces remains a challenge due to the flammability and ignition.Motivated by this,this study proposed a machining process,named the ultraprecision diamond surface texturing process,to machine the micro/nanostructures on magnesium alloy surfaces.Experimental results showed the various microstructures and sawtooth-shaped nanostructures were successfully generated on the AZ31B magnesium alloy surfaces,demonstrating the effectiveness of this proposed machining process.Furthermore,sawtooth-shaped nanostructures had the function of inducing the optical effect and generating different colors on workpiece surfaces.The colorful letter and colorful flower image were clearly viewed on magnesium alloy surfaces.The corresponding cutting force,chip morphology,and tool wear were systematically investigated to understand the machining mechanism of micro/nanostructures on magnesium alloy surfaces.The proposed machining process can further improve the performances of the magnesium alloy and extend its functions to other fields,such as optics.
基金the grants received from the Science and Engineering Research Board(SERB),New Delhi(SR/S3/ME/0024/2011,dated 3rd July 2012)。
文摘Zirconia(ZrO_2)incorporated ceramic coatings were fabricated on biodegradable ZM21 Mg alloy by the PEO coupled with EPD process.Subsequently,the sample surface was modified by laser texturing to improve the corrosion resistance,roughness and cell proliferation and growth properties.The corrosion performance of the fabricated samples along with the substrate was studied by electrochemical measurements under simulated body fluid(SBF)environment.The cell direct contact assay was conducted for the substrate and fabricated samples using L-929 mouse fibroblast cells for 24 h.The phase contrast images of cell direct contact assay revealed that fabricated samples exhibited better contact and response with the fibroblast cells,compared to the substrate.The addition of nanoparticles in the PEO process,called PEO coupled EPD process,resulted in attaining a higher thickness and improved corrosion performance of the samples than the PEO coated samples.Among all the samples,laser surface textured PEO,and PEO-EPD coated samples unveiled enhanced corrosion resistance,cell growth,thereby enabling it as a suitable prototype for biodegradable implant applications.
基金supported by a Grant-in-Aid for Scientific Research on Innovative Areas "New Polymeric Materials Based on Element-Blocks (No. 2401)" (24102004) of The Ministry of Education, Culture, Sports, Science, and Technology, Japan
文摘Unique and various microstructures of titanium oxide(TiO_2 ) film including macroporous structure, chromatic veins and rings, have been easily fabricated by mist deposition method on silicon substrate with mild preparation conditions. Rutile phase TiO_2 nanoparticles were directly used as starting material to prepare film and led to a simple preparation process. It was found that several different microstructures existed in the sample and changed with the varied positions from the center to the edge of the film when the concentration of the TiO_2 suspension is 0.06 mol/l, the deposition time is 30 min, the flow rate is 1 l/min and the temperature is150. The surface texturing shows apparent distinction as the concentration of the TiO_2 suspension decreased to 0.03 mol/l and 0.01 mol/l.
文摘The contact fatigue life of machine elements is affected by pitting, wear and so on, under heavier loading conditions. Increasing the fatigue life requires mainly the improvements of lubricating condition, operating condition and materials. In order to improve the lubricating condition, it is necessary to investigate the relation of the microscopic surface texturing and the contact modes of machine elements. In this paper, thus, the pressure and oil film thickness of the contact between sphere and the plate with 5 kinds surface texturing were calculated using a commercial software based on Reynolds equation. There was sufficient evidence to suggest that the dimple shape was the optimum texturing to increase the lubricating condition.
文摘The relationship between the structure of PP drawn filament and the crimp elasticity of tex-tured yarn is investigated.It is found that orientation,crystallinity,and especially,crystalline formof drawn filament are related to crimp property of textured yarn.Lower crystallinity,moderateorientation and unstable para-crystalline structure are necessary for increasing crimp elasticity.Inaddition,the filament structure and properties before and after texturing are compared.
基金This work was supported by the Nationa!Natural Science Foundation of China(No.50376067)National High Technical Research and Development Programme of China(No.2001AA513060).
文摘An isotropic etching technique of texturing silicon solar cells has been applied to polycrystalline silicon wafers with different acid concentrations. Optimal e tching conditions have been determined by etching rate calculation, scanning ele ctron microscope (SEM) image and reflectance measurement. The surface morphology of the textured wafers varies in accordance with the different etchant concentr ation which in turn leads to the dissimilarity of etching speed. Textured polycr ystalline silicon wafer surfaces display randomly located etched pits which can reduce the surface reflection and enhance the light absorption. The special rela tionship between reflectivity and etching rate was studied. Reflectance measurem ents show that isotropic texturing is one of the suitable techniques for texturi ng polycrystalline silicon wafers and benefits solar cells performances.
基金supported by Dokuz Eylul University under project no.2021.KB.FEN.043.
文摘This study presents a comprehensive approach to applying texturing processes created by engraving on the surface of CoCr28Mo alloy workpieces using a 20 W pulsed nanosecond fiber laser.The hatch strategy and distance,frequency,and scan speed were control parameters for texturing applications.The effectiveness of the parameters in terms of roughness and contact angle of the texturized surface was investigated.Surface roughness and contact angle were analyzed using variance analysis to identify each variable's influence.It has been determined that the roughness of the texture defined by the hatch strategy plays a decisive role in the wettability behavior of the surface;however,the scan speed,frequency,and hatch distance which are among the laser surface texturing conditions are influential in the roughness and contact angle.Increasing scan speed and hatch distance while decreasing frequency resulted in smoother surfaces,increasing the contact angle.Textures having rough surfaces produced with different processing conditions exhibit a super hydrophilic behavior.The contact angle is most sensitive to the hatch distance;however,the frequency has the least influence on the contact angle.The most and least efficient surface roughness parameters are revealed to be scan speed and hatch distance,respectively.
