Biomass-derived carbon materials are favored for their abundance and sustainability,and ease of preparation and modification.By surface activation and modification they can have a good electrical conductivity,excellen...Biomass-derived carbon materials are favored for their abundance and sustainability,and ease of preparation and modification.By surface activation and modification they can have a good electrical conductivity,excellent catalytic activity,a remarkable adsorption capacity,and different interfacial physicochemical functionalities.Surface-modified biochars have found wide applications in energy storage,environmental remediation,and catalysis.However,achieving precise and controllable modification of their active sites remains a challenge.Recent advances and future prospects for controlling their surface morphology,defect engineering,and surface coating strategies,with particular attention to their means of fabrication,are reviewed.展开更多
Two-step-processed(TSP)inverted p-i-n perovskite solar cells(PSCs)have demonstrated significant promise in tandem applications.However,the power conversion efficiency(PCE)of TSP p-i-n PSCs rarely exceeds 24%.Here,we d...Two-step-processed(TSP)inverted p-i-n perovskite solar cells(PSCs)have demonstrated significant promise in tandem applications.However,the power conversion efficiency(PCE)of TSP p-i-n PSCs rarely exceeds 24%.Here,we demonstrate that TSP perovskite films exhibit a vertically gradient distribution of residual PbI_(2)clusters,which form Schottky heterojunctions with the perovskite,leading to substantial interfacial energy-level mismatches within NiO_(x)-based TSP p-i-n PSCs.These limitations were effectively addressed via a vertical interfacial engineering enabled by dual-interface modification incorporating tin trifluoromethanesulfonate(Sn(OTF)_(2))and 4-Fluorophenylethylamine chloride(F-PEA)at the NiO_(x)/perovskite and perovskite/C60 interfaces,respectively.The functional Sn(OTF)_(2)not only enhances the conductivity of NiO_(x)films but also suppresses ion migration,while inducing the formation of a Pb-Sn mixed perovskite interlayer that precisely regulates the energy level at the NiO_(x)/perovskite interface.Complementally,F-PEA post-treatment effectively converts surface residual PbI_(2)clusters into a 2D perovskite capping layer,which simultaneously passivates surface defects and enhances energy-level alignment at the perovskite/C60 interface.Consequently,the optimized NiO_(x)-based TSP p-i-n PSCs achieve a notable PCE of 25.6%with superior operational stability.This study elucidates the underlying mechanisms limiting the efficiency of TSP p-i-n PSCs,while establishing design principles for these devices targeting 26%efficiency.展开更多
The presence of a surface oxide film(B_(2)O_(3))on boron(B)particles significantly compromises their combustion efficiency and kinetic performance in fuel-rich solid propellants.This study proposes an innovative conti...The presence of a surface oxide film(B_(2)O_(3))on boron(B)particles significantly compromises their combustion efficiency and kinetic performance in fuel-rich solid propellants.This study proposes an innovative continuous modification strategy combining non-thermal plasma(NTP)etching with fluorocarbon passivation.Characterization and kinetic analysis revealed that reactive plasma species—including atomic hydrogen(H),electronically excited molecular hydrogen(H_(2)^(*)),vibrationally excited molecular hydrogen(H_(2)v),and hydrogen ions(H^(+))—dominate the reduction of B_(2)O_(3)through lowering the transition energy barrier and shifting the reaction spontaneity.Subsequent argon plasma fragmentation of C_(8)F_(18)generates fluorocarbon radicals that form conformal passivation coatings(thickness:7 nm)on purified boron surfaces.The modified boron particles exhibit 37.5℃lower exothermic peak temperature and 27.2%higher heat release(14.8 kJ/g vs.11.6 kJ/g)compared to untreated counterparts.Combustion diagnostics reveal 194%increase in maximum flame height(135.10 mm vs.46.03 mm)and 134%enhancement in flame propagation rate(4.44 cm/s vs.1.90 cm/s).This NTP-based surface engineering approach establishes a scalable pathway for developing highperformance boron-based energetic composites.展开更多
We are sorry for the mistakes of Affiliation,"a State Key Laboratory of Advanced Fiber Materials,Center for Advanced Low-Dimension Materials,Donghua University,Shanghai 201620,China"should be replaced by&quo...We are sorry for the mistakes of Affiliation,"a State Key Laboratory of Advanced Fiber Materials,Center for Advanced Low-Dimension Materials,Donghua University,Shanghai 201620,China"should be replaced by"a State Key Laboratory of Advanced Fiber Materials,Center for Advanced Low-Dimension Materials,College of Materials Science and Engineering,Donghua University,Shanghai 201620,China".We apologized for the inconvenience caused by this error.展开更多
Hydroxyapatite （ HA ）- reinforced high density polyethylene （HDPE） was developed as a bone replacement material,In order to enhaace the interfacial bonding between HA and polyethylene and improve the mechanical ...Hydroxyapatite （ HA ）- reinforced high density polyethylene （HDPE） was developed as a bone replacement material,In order to enhaace the interfacial bonding between HA and polyethylene and improve the mechanical properties of HDPE/ HA composites, the surface of the micron-sized HA particles was modified by in situ polymerization of butyl acrylate （ BA ） and in situ copolymerization of vinyl triethoxyl silane （ VTES ） and BA , then the modifwd HA particles were compounded with HDPE. The effects of the surface modification of HA on morphology and mechanical properties of HDPE/ HA composites were investigated. The experimental results show that the presence of HA particles does tuft inhibit the polymerization of BA . The poly（ butyl acrylate） （ PBA ） segments on the HA surface enhance the compatibility between HA and HDPE, improve the dispersion of HA particles in HDPE matrix, and enhance the interfacial adhesion between HA and matrix. Surface modifieations , especially by in situ copolymerization of VTES and BA, significantly increase notch impact strengths and marginal stiffness and tensile strengths of HDPE/HA composites. And it is found that there is a critical thickness of PBA coating on HA panicles for optimum mechanical properties of HDPE / HA composites.展开更多
Ultra-high molecular weight polyethylene(UHMWPE)fiber is a new kind of high-performance fiber.Due to its excellent physical and chemical characteristics,it is widely used in various fields.However,the surface UHMWPE f...Ultra-high molecular weight polyethylene(UHMWPE)fiber is a new kind of high-performance fiber.Due to its excellent physical and chemical characteristics,it is widely used in various fields.However,the surface UHMWPE fiber is smooth and demonstrates no-polar groups.The weak interfacial adhesion between fiber and resin seri-ously restricts the applications of UHMWPE fiber.Therefore,the surface modification treatments of UHMWPE fiber are used to improve the interfacial adhesion strength.The modified method by adding nanomaterials elu-cidates the easy fabrication,advanced equipment and proper technology.Thus,the progress of UHMWPE nanocomposite fibers prepared via adding various nanofillers are reviewed.Meanwhile,the effects of other various methods on surface modification are also reviewed.This work advances the various design strategies about nano technologies on improving interfacial adhesion performance via treatment methodologies.展开更多
Infections associated with titanium(Ti)-based implants present significant challenges in clinical treatments,especially when biofilms already form on the implant surface.Many antimicrobial agents,including antibiotics...Infections associated with titanium(Ti)-based implants present significant challenges in clinical treatments,especially when biofilms already form on the implant surface.Many antimicrobial agents,including antibiotics,metallic nanoparticles and antimicrobial peptides,have been extensively used to deal with Ti implant infections.However,these chemical approaches suffer from potential toxicity,antibiotic resistance and poor long-term antibacterial performance.Hence,physical antibacterial surfaces on Ti-based implants have attracted increasing attention.The antibacterial behavior of different surfaces on Ti-based biomaterials against various bacteria only by physical properties of the implants themselves(e.g.,nanotopography)or exogenous physical stimulus(e.g.,photocatalysis)was reviewed,as well as parameters influencing the physical antibacterial processes,such as size,shape and density of the surface nanotextures,and bacterial growth phases.Besides,mechanisms of different fabrication techniques for the physical antibacterial surfaces on Ti-based biomaterials were also summarized.展开更多
Additive manufacturing(AM)has revolutionized the production of metal bone implants,enabling unprecedented levels of customization and functionality.Recent advancements in surface-modification technologies have been cr...Additive manufacturing(AM)has revolutionized the production of metal bone implants,enabling unprecedented levels of customization and functionality.Recent advancements in surface-modification technologies have been crucial in enhancing the performance and biocompatibility of implants.Through leveraging the versatility of AM techniques,particularly powder bed fusion,a range of metallic biomaterials,including stainless steel,titanium,and biodegradable alloys,can be utilized to fabricate implants tailored for craniofacial,trunk,and limb bone reconstructions.However,the potential of AM is contingent on addressing intrinsic defects that may hinder implant performance.Techniques such as sandblasting,chemical treatment,electropolishing,heat treatment,and laser technology effectively remove residual powder and improve the surface roughness of these implants.The development of functional coatings,applied via both dry and wet methods,represents a significant advancement in surface modification research.These coatings not only improve mechanical and biological interactions at the implant-bone interface but also facilitate controlled drug release and enhance antimicrobial properties.Addition-ally,micro-and nanoscale surface modifications using chemical and laser techniques can precisely sculpt implant surfaces to promote the desired cellular responses.This detailed exploration of surface engineering offers a wealth of opportunities for creating next-generation implants that are not only biocompatible but also bioactive,laying the foundation for more effective solutions in bone reconstruction.展开更多
Biodegradable metals have garnered considerable interest owing to their capacity for self-degradation following the repair of damaged tissues.This review commences with their historical development and clarifies the e...Biodegradable metals have garnered considerable interest owing to their capacity for self-degradation following the repair of damaged tissues.This review commences with their historical development and clarifies the essential prerequisites for their successful clinical translation.Subsequently,a detailed review of magnesium-based materials is presented from five critical areas of alloying,fabrication techniques,purification,surface modification,and structural design,systematically addressing their progress in biodegradation rate retardation,mechanical reinforcement,and biocompatibility enhancement.Furthermore,recent breakthroughs in vivo animal experiments and clinical translation of magnesium alloys are summarized.Finally,this review concludes with a critical assessment of the achievements and challenges encountered in the clinical application of these materials,and proposes practical strategies to address current limitations and guide future research perspectives.展开更多
Silica fibers were modified by a specific ratio of SiB6 mixed with silica sol through vacuum impregnation method.The modified fibers were then incorporated into a phenolic resin matrix to prepare fiber-reinforced resi...Silica fibers were modified by a specific ratio of SiB6 mixed with silica sol through vacuum impregnation method.The modified fibers were then incorporated into a phenolic resin matrix to prepare fiber-reinforced resin composites.The influences of the SiB_(6)/SiO_(2)mixed modification on silica fiber properties were analyzed through thermogravimetric analysis(TGA),differential scanning calorimetry(DSC),scanning electron microscopy(SEM),and X-ray diffraction(XRD),respectively.Additionally,the influence of the SiB_(6)/SiO_(2)mixed modification on the mechanical properties of phenolic resin matrix composites was evaluated through mechanical testing.The experimeatal results indicate that the SiB_(6)/SiO_(2)mixed surface modification shows significant improvement in strength at room temperature and high temperatures,and crystallization temperature of silica fiber increases.The SiB_(6)/Silica sol co-modified silica fiber shows potential for future application in thermal protection and other high-temperature conditions.展开更多
Single crystalline nickel rich Li[Ni_(x)Co_(y)Mn_(1-x–y)]O_(2)(SCNCM)layered oxide cathodes show higher ionic conductivity and better structure integrity than polycrystalline NCM(PCNCM)cathodes by eliminating grain b...Single crystalline nickel rich Li[Ni_(x)Co_(y)Mn_(1-x–y)]O_(2)(SCNCM)layered oxide cathodes show higher ionic conductivity and better structure integrity than polycrystalline NCM(PCNCM)cathodes by eliminating grain boundaries.However,it remains challenges in the controlled synthesis process and restricted cycling stability of SCNCM.Herein,take single crystalline nickel rich Li[Ni_(0.8)Co_(0.1)Mn_(0.1)]O_(2)(SC811)as an example,a dual molten salts(LiOH and Li_(2)SO_(4))assisted secondary calcination method is proposed,for which LiOH salt improves primary crystal size and Li_(2)SO_(4)prevents the aggravation of NCM nanocrystals.To further reduce the interfacial side reactions,Mg-doping and B-coating surface modification was carried out,which effectively suppress anisotropic lattice changes and Li/Ni disorder.In addition,a thin and uniform H_(3)BO_(3)coating effectively prevents direct contact between the electrode and electrolyte,thus reducing harmful parasitic reactions.The single crystal structure engineering and surface modification strategy of oxide layered cathodes significantly improve the cycling stability of the modified SC811 cathode.For example,during a long-term cycling of 470 cycles,a high-capacity retention of 74.2%obtained at 1C rate.Our work provides a new strategy for engineering high energy nickel rich layered oxide NCM cathodes.展开更多
Four types of submicron Ag-coated Cu particles with different Ag contents were prepared as sintering paste fillers,and the Ag contents of the particles were measured to be 10,20,30,and 40 wt.%.Four types of particles(...Four types of submicron Ag-coated Cu particles with different Ag contents were prepared as sintering paste fillers,and the Ag contents of the particles were measured to be 10,20,30,and 40 wt.%.Four types of particles(in order of increasing Ag content:A10,A20,A30,and A40)were surface-modified with stearic acid,to suppress the Ag shell dewetting and improve sinterability.The surface-modified particles were mixed with a polyol-based solvent to fabricate a resin-free paste.Subsequently,the pastes were screen-printed onto a slide glass and sintered at 250°C in a nitrogen atmosphere for 1-10 min to form an electrode.The electrical resistivity of the sintered film as a function of sintering time was measured using a four-point probe.All the four surface-modified Cu@Ag particles with different Ag contents exhibited decreased electrical resistivity.Particularly,the largest difference in values after and before the surface modification was observed for A40 with the highest Ag content;the electrical resistivities of the initial and surface-modified particles were 1.51×10^(-4) and 6.67×10^(-5)Ω·cm,respectively,after sintering for 10 min.The findings of this study confirmed that the surface modification using stearic acid effectively suppressed the dewetting of the Ag shell and improved the sinterability of the submicron Cu@Ag particles.展开更多
In this paper,the stability of the results of ultrasonic wood surface modification after long-term storage,including macroscopic properties and microstructure of specimens,was investigated.Specimens of aspen wood(Popu...In this paper,the stability of the results of ultrasonic wood surface modification after long-term storage,including macroscopic properties and microstructure of specimens,was investigated.Specimens of aspen wood(Populus tremula)were processed by the developed ultrasonic method of wood surface modification in three different treatment modes and the surface hardness of the specimens was evaluated after processing and after storing the specimens for more than 5 years since long-term stability is an important factor for the use of ultrasonically modified sawn timber as construction and finishing materials.The obtained results of surface hardness measurements by the Leeb method showed that the decrease in hardness after long-term storage is approximately 6.6%for the lowest degree of treatment and approximately 3.4%and 2.4%for medium and high degrees of treatment,taking into account the fact of the average increase in surface hardness approximately 2–4 times,this decrease is insignificant.The internal structure of the specimens after storage was studied by scanning electron microscope(SEM),and deformations of the wood surface layer without damage or rupture were analyzed.The derived stable results confirm the potential of the ultrasonic method for wood surface modification.展开更多
In this study,an amine-reactive poly(pentafluorophenyl acrylate)(PPFPA)platform was developed for advanced surface engineering of next-generation sequencing(NGS)chips.Through post-polymerization modification,PPFPA was...In this study,an amine-reactive poly(pentafluorophenyl acrylate)(PPFPA)platform was developed for advanced surface engineering of next-generation sequencing(NGS)chips.Through post-polymerization modification,PPFPA was functionalized with dual moieties:azide groups for covalent immobilization of DBCO-modified DNA primers via click chemistry and tunable hydrophilic side chains to optimize biocompatibility and surface properties.Systematic screening revealed that hydrophobic azide carriers combined with neutral hydroxyl groups maximized the DNA immobilization efficacy,approaching the performance of commercial polyacrylamide-based polymers.The negatively charged carboxyl groups severely impede DNA primer attachment.Higher molecular weight derivatives further enhance the efficacy of DNA immobilization.In NGS validation,optimized surface modification polymers achieved robust surface density of clustered DNA and high sequencing accuracy,surpassing quality benchmarks and comparable to those of conventional analogs.This platform demonstrates significant potential for tailoring high-sensitivity surfaces for genomic applications,advancing clinical diagnostics,and personalized medicine.展开更多
Silicon carbide(SiC)is a highly valued material for power semiconductor devices due to its wide bandgap,high thermal conductivity,and high breakdown electric field.However,its high hardness,brittleness,and chemical st...Silicon carbide(SiC)is a highly valued material for power semiconductor devices due to its wide bandgap,high thermal conductivity,and high breakdown electric field.However,its high hardness,brittleness,and chemical stability present substantial challenges for efficient and high-quality processing.This study investigated the effects of picosecond laser surface scanning on 4H-SiC to enhance the material removal performance.The research focused on surface morphology,phase transitions,subsurface/interface characteristics,and material removal mechanisms under varying laser parameters.The results demonstrate that the laser thermal effect decomposes 4H-SiC into amorphous silicon(a-Si),disordered carbon,and graphite,forming a resolidified layer containing Si-O and Si-C-O oxides.Crystalline silicon(c-Si)is produced under high fluences or extensive irradiations.The variation in the resolidified layer thickness with changing laser parameters is revealed.A detailed laser-induced subsurface damage model is developed,encompassing a resolidified layer that includes the above decomposition and oxidation products,and a deformed layer formed primarily under laser-induced stress.The presence of the resolidified layer and the deformed layer leads to a decreased elastic recovery rate and an increased scratching depth,exceeding 2.5 times that of the unmodified condition.Enhanced material removal performance is mainly driven by the resolidified layer at low fluence and by the deformed layer at high fluence.When aligning the total of the ablation depth and the resolidified layer thickness with the subsurface damage depth in the original material,excellent polishing performance is achieved.These findings provide critical insights for understanding the phase evolution,subsurface damage mechanisms,and material removal behavior of 4H-SiC,offering valuable guidance for optimizing the laser surface modification parameters to achieve high-efficiency processing.展开更多
Surface modification of fabrics is an effective way to endow them with antifouling properties while still maintaining their key advantages such as comfort,softness and stretchability.Herein,an atmospheric pressure die...Surface modification of fabrics is an effective way to endow them with antifouling properties while still maintaining their key advantages such as comfort,softness and stretchability.Herein,an atmospheric pressure dielectric barrier discharge(DBD)plasma method is demonstrated for the processing of silk fabrics using 1H,1H,2H,2H-perfluorodecyltriethoxysilane(PFDS)as the precursor.The results showed the successful grafting of PFDS groups onto the surface of silk fabrics without causing damage.Meanwhile,the gas temperature is rather low during the whole processing procedure,suggesting the non-equilibrium characteristics of DBD plasma.The influence on fabrics of the processing parameters(PFDS concentration,plasma treatment time and plasma discharge power)was systematically investigated.An optimum processing condition was determined to be a PFDS concentration of 8wt%,a plasma processing time of 40 s and a plasma power of 11.87 W.However,with prolonged plasma processing time or enhanced plasma power,the plasma-grafted PFDS films could be degraded.Further study revealed that plasma processing of silk fabrics with PFDS would lead to a change in their chemical composition and surface roughness.As a result,the surface energy of the fabrics was reduced,accompanied by improved water and oil repellency as well as enhanced antifouling performance.Besides,the plasma-grafted PFDS films also had good durability and stability.By extending the method to polyester and wool against different oil-/water-based stains,the DBD plasma surface modification technique demonstrated good versatility in improving the antifouling properties of fabrics.This work provides guidance for the surface modification of fabrics using DBD plasma to confer them with desirable functionalities.展开更多
Nano zero-valent iron(nZVI)is a promising phosphate adsorbent for advanced phosphate removal.However,the rapid passivation of nZVI and the low activity of adsorption sites seriously limit its phosphate removal perform...Nano zero-valent iron(nZVI)is a promising phosphate adsorbent for advanced phosphate removal.However,the rapid passivation of nZVI and the low activity of adsorption sites seriously limit its phosphate removal performance,accounting for its inapplicability to meet the emission criteria of 0.1 mg P/L phosphate.In this study,we report that the oxalate modification can inhibit the passivation of nZVI and alter the multi-stage phosphate adsorption mechanism by changing the adsorption sites.As expected,the stronger antipassivation ability of oxalate modified nZVI(OX-nZVI)strongly favored its phosphate adsorption.Interestingly,the oxalate modification endowed the surface Fe(III)sites with the lowest chemisorption energy and the fastest phosphate adsorption ability than the other adsorption sites,by in situ forming a Fe(III)-phosphate-oxalate ternary complex,therefore enabling an advanced phosphate removal process.At an initial phosphate concentration of 1.00 mg P/L,pH of 6.0 and a dosage of 0.3 g/L of adsorbents,OX-nZVI exhibited faster phosphate removal rate(0.11 g/mg/min)and lower residual phosphate level(0.02 mg P/L)than nZVI(0.055 g/mg/min and 0.19 mg P/L).This study sheds light on the importance of site manipulation in the development of high-performance adsorbents,and offers a facile surface modification strategy to prepare superior iron-basedmaterials for advanced phosphate removal.展开更多
Expanding the specific surface area of substrates and carrying out precise surface engineering of imprinted nanocavities are crucial methods for enhancing the identification efficiency of molecularly imprinted polymer...Expanding the specific surface area of substrates and carrying out precise surface engineering of imprinted nanocavities are crucial methods for enhancing the identification efficiency of molecularly imprinted polymers(MIPs).To implement this synergistic strategy,bioinspired surface engineering was used to incorporate dual covalent receptors via precise post-imprinting modifications(PIMs)onto mesoporous silica nanosheets.The prepared sorbents(denoted as‘‘D-PMIPs”)were utilized to improve the specific identification of adenosine 5-monophosphate(AMP).Significantly,the mesoporous silica nanosheets possess a high surface area of approximately 498.73 m^(2)·g^(-1),which facilitates the formation of abundant specific recognition sites in the D-PMIPs.The dual covalent receptors are valuable for estab-lishing the spatial orientation and arrangement of AMP through multiple cooperative interactions.PIMs enable precise site-specific functionalization within the imprinted cavities,leading to the tailor-made formation of complementary binding sites.The maximum number of high-affinity binding sites(Nmax)of the D-PMIPs is 39.99 lmol·g^(-1),which is significantly higher than that of imprinted sorbents with a sin-gle receptor(i.e.,S-BMIPs or S-PMIPs).The kinetic data of the D-PMIPs can be effectively described by a pseudo-second-order model,indicating that the main binding mechanism involves synergistic chemisorption from boronate affinity and the pyrimidine base.This study suggests that using dual cova-lent receptors and PIMs is a reliable approach for creating imprinted sorbents with high selectivity,allow-ing for the controlled engineering of imprinted sites.展开更多
The surface and interfacial properties of polymeric bonding agents and nitramine crystal fillers were studied. The surface free energy and adhesion work of polymeric bonding agents and nitramine fillers were calculate...The surface and interfacial properties of polymeric bonding agents and nitramine crystal fillers were studied. The surface free energy and adhesion work of polymeric bonding agents and nitramine fillers were calculated by using Kaeble′s equations. It was observed that the hydroxyl values of neutral polymeric bonding agents (NPBA) correlate well with the polar components of surface free energies. On the basis of the measurements of swelling ratio and initial modulus, the interfacial bonding through highly crosslinked polymeric shell formation around the nitramine particles and generating interfacial reinforcement were rationalized. The application of Tapping Mode AFM (atomic force micro scope) to observing the surface morphology of NPBA reveals that methyl acrylate monomer appears to play a role for aiding the formation of network like structure when nanometer scale images of NPBA are created.展开更多
A Cu-25Cr alloy prepared by vacuum induction melting method was treated by the high current pulsed electron beam （HCPEB） with pulse numbers ranging from 1 to 100. Surface morphologies and microstructures of the allo...A Cu-25Cr alloy prepared by vacuum induction melting method was treated by the high current pulsed electron beam （HCPEB） with pulse numbers ranging from 1 to 100. Surface morphologies and microstructures of the alloy before and after the treatment were investigated by scanning electron microscopy and X-ray diffraction. The results show that significant surface modification can be induced by HCPEB with the pulse number reaching 10. Craters with typical morphologies on the Cu-25Cr alloy surface are formed due to the dynamic thermal field induced by the HCPEB. Micro-cracks, as a unique feature, are well revealed in the irradiated Cu-25Cr specimens and attributed to quasi-static thermal stresses accumulated along the specimen surface. The amount of cracks is found to increase with the pulse number and a preference of these cracks to Cr phases rather than Cu phases is also noted. Another characteristic produced by the HCPEB is the fine Cr spheroids, which are determined to be due to occurrence of liquid phase separation in the Cu-25Cr alloy. In addition, an examination on surface roughness of all specimens reveals that more pulses will produce a roughened surface, as a result of compromising the above features.展开更多
文摘Biomass-derived carbon materials are favored for their abundance and sustainability,and ease of preparation and modification.By surface activation and modification they can have a good electrical conductivity,excellent catalytic activity,a remarkable adsorption capacity,and different interfacial physicochemical functionalities.Surface-modified biochars have found wide applications in energy storage,environmental remediation,and catalysis.However,achieving precise and controllable modification of their active sites remains a challenge.Recent advances and future prospects for controlling their surface morphology,defect engineering,and surface coating strategies,with particular attention to their means of fabrication,are reviewed.
基金supported by the National Nature Science Foundation of China(62504130)National Key Research and Development Program of China(2018YFB0704100)+1 种基金the Key university laboratory of highly efficient utilization of solar energy and sustainable development of Guangdong(Y01256331)the Technology Development Project of Henan Province(252102240047).
文摘Two-step-processed(TSP)inverted p-i-n perovskite solar cells(PSCs)have demonstrated significant promise in tandem applications.However,the power conversion efficiency(PCE)of TSP p-i-n PSCs rarely exceeds 24%.Here,we demonstrate that TSP perovskite films exhibit a vertically gradient distribution of residual PbI_(2)clusters,which form Schottky heterojunctions with the perovskite,leading to substantial interfacial energy-level mismatches within NiO_(x)-based TSP p-i-n PSCs.These limitations were effectively addressed via a vertical interfacial engineering enabled by dual-interface modification incorporating tin trifluoromethanesulfonate(Sn(OTF)_(2))and 4-Fluorophenylethylamine chloride(F-PEA)at the NiO_(x)/perovskite and perovskite/C60 interfaces,respectively.The functional Sn(OTF)_(2)not only enhances the conductivity of NiO_(x)films but also suppresses ion migration,while inducing the formation of a Pb-Sn mixed perovskite interlayer that precisely regulates the energy level at the NiO_(x)/perovskite interface.Complementally,F-PEA post-treatment effectively converts surface residual PbI_(2)clusters into a 2D perovskite capping layer,which simultaneously passivates surface defects and enhances energy-level alignment at the perovskite/C60 interface.Consequently,the optimized NiO_(x)-based TSP p-i-n PSCs achieve a notable PCE of 25.6%with superior operational stability.This study elucidates the underlying mechanisms limiting the efficiency of TSP p-i-n PSCs,while establishing design principles for these devices targeting 26%efficiency.
基金supported by the National Natural Science Foundation of China(Nos.U2341249,12005076,22205112)the Fundamental Research Funds for the Central Universities(No.2025201012)。
文摘The presence of a surface oxide film(B_(2)O_(3))on boron(B)particles significantly compromises their combustion efficiency and kinetic performance in fuel-rich solid propellants.This study proposes an innovative continuous modification strategy combining non-thermal plasma(NTP)etching with fluorocarbon passivation.Characterization and kinetic analysis revealed that reactive plasma species—including atomic hydrogen(H),electronically excited molecular hydrogen(H_(2)^(*)),vibrationally excited molecular hydrogen(H_(2)v),and hydrogen ions(H^(+))—dominate the reduction of B_(2)O_(3)through lowering the transition energy barrier and shifting the reaction spontaneity.Subsequent argon plasma fragmentation of C_(8)F_(18)generates fluorocarbon radicals that form conformal passivation coatings(thickness:7 nm)on purified boron surfaces.The modified boron particles exhibit 37.5℃lower exothermic peak temperature and 27.2%higher heat release(14.8 kJ/g vs.11.6 kJ/g)compared to untreated counterparts.Combustion diagnostics reveal 194%increase in maximum flame height(135.10 mm vs.46.03 mm)and 134%enhancement in flame propagation rate(4.44 cm/s vs.1.90 cm/s).This NTP-based surface engineering approach establishes a scalable pathway for developing highperformance boron-based energetic composites.
文摘We are sorry for the mistakes of Affiliation,"a State Key Laboratory of Advanced Fiber Materials,Center for Advanced Low-Dimension Materials,Donghua University,Shanghai 201620,China"should be replaced by"a State Key Laboratory of Advanced Fiber Materials,Center for Advanced Low-Dimension Materials,College of Materials Science and Engineering,Donghua University,Shanghai 201620,China".We apologized for the inconvenience caused by this error.
文摘Hydroxyapatite （ HA ）- reinforced high density polyethylene （HDPE） was developed as a bone replacement material,In order to enhaace the interfacial bonding between HA and polyethylene and improve the mechanical properties of HDPE/ HA composites, the surface of the micron-sized HA particles was modified by in situ polymerization of butyl acrylate （ BA ） and in situ copolymerization of vinyl triethoxyl silane （ VTES ） and BA , then the modifwd HA particles were compounded with HDPE. The effects of the surface modification of HA on morphology and mechanical properties of HDPE/ HA composites were investigated. The experimental results show that the presence of HA particles does tuft inhibit the polymerization of BA . The poly（ butyl acrylate） （ PBA ） segments on the HA surface enhance the compatibility between HA and HDPE, improve the dispersion of HA particles in HDPE matrix, and enhance the interfacial adhesion between HA and matrix. Surface modifieations , especially by in situ copolymerization of VTES and BA, significantly increase notch impact strengths and marginal stiffness and tensile strengths of HDPE/HA composites. And it is found that there is a critical thickness of PBA coating on HA panicles for optimum mechanical properties of HDPE / HA composites.
文摘Ultra-high molecular weight polyethylene(UHMWPE)fiber is a new kind of high-performance fiber.Due to its excellent physical and chemical characteristics,it is widely used in various fields.However,the surface UHMWPE fiber is smooth and demonstrates no-polar groups.The weak interfacial adhesion between fiber and resin seri-ously restricts the applications of UHMWPE fiber.Therefore,the surface modification treatments of UHMWPE fiber are used to improve the interfacial adhesion strength.The modified method by adding nanomaterials elu-cidates the easy fabrication,advanced equipment and proper technology.Thus,the progress of UHMWPE nanocomposite fibers prepared via adding various nanofillers are reviewed.Meanwhile,the effects of other various methods on surface modification are also reviewed.This work advances the various design strategies about nano technologies on improving interfacial adhesion performance via treatment methodologies.
基金National Natural Science Foundation of China(52171114)。
文摘Infections associated with titanium(Ti)-based implants present significant challenges in clinical treatments,especially when biofilms already form on the implant surface.Many antimicrobial agents,including antibiotics,metallic nanoparticles and antimicrobial peptides,have been extensively used to deal with Ti implant infections.However,these chemical approaches suffer from potential toxicity,antibiotic resistance and poor long-term antibacterial performance.Hence,physical antibacterial surfaces on Ti-based implants have attracted increasing attention.The antibacterial behavior of different surfaces on Ti-based biomaterials against various bacteria only by physical properties of the implants themselves(e.g.,nanotopography)or exogenous physical stimulus(e.g.,photocatalysis)was reviewed,as well as parameters influencing the physical antibacterial processes,such as size,shape and density of the surface nanotextures,and bacterial growth phases.Besides,mechanisms of different fabrication techniques for the physical antibacterial surfaces on Ti-based biomaterials were also summarized.
基金supported by National Natural Science Foundation of China(Grant No.52275343)Natural Science Foundation of Zhejiang Province(Grant No.LY23E050003)Ningbo Youth Science and Technology Innovation Leading Talent Project(Grant No.2023QL021).
文摘Additive manufacturing(AM)has revolutionized the production of metal bone implants,enabling unprecedented levels of customization and functionality.Recent advancements in surface-modification technologies have been crucial in enhancing the performance and biocompatibility of implants.Through leveraging the versatility of AM techniques,particularly powder bed fusion,a range of metallic biomaterials,including stainless steel,titanium,and biodegradable alloys,can be utilized to fabricate implants tailored for craniofacial,trunk,and limb bone reconstructions.However,the potential of AM is contingent on addressing intrinsic defects that may hinder implant performance.Techniques such as sandblasting,chemical treatment,electropolishing,heat treatment,and laser technology effectively remove residual powder and improve the surface roughness of these implants.The development of functional coatings,applied via both dry and wet methods,represents a significant advancement in surface modification research.These coatings not only improve mechanical and biological interactions at the implant-bone interface but also facilitate controlled drug release and enhance antimicrobial properties.Addition-ally,micro-and nanoscale surface modifications using chemical and laser techniques can precisely sculpt implant surfaces to promote the desired cellular responses.This detailed exploration of surface engineering offers a wealth of opportunities for creating next-generation implants that are not only biocompatible but also bioactive,laying the foundation for more effective solutions in bone reconstruction.
基金supported by the Science and Technology Planning Project of Guangdong Province(Nos.2024A0505040016 and 2023A0505050148)National Key Research and Development Project of China(2023YFB3809900/2023YFB3809902)Natural Science Foundation of Guangdong Province(No.2025A1515010026)。
文摘Biodegradable metals have garnered considerable interest owing to their capacity for self-degradation following the repair of damaged tissues.This review commences with their historical development and clarifies the essential prerequisites for their successful clinical translation.Subsequently,a detailed review of magnesium-based materials is presented from five critical areas of alloying,fabrication techniques,purification,surface modification,and structural design,systematically addressing their progress in biodegradation rate retardation,mechanical reinforcement,and biocompatibility enhancement.Furthermore,recent breakthroughs in vivo animal experiments and clinical translation of magnesium alloys are summarized.Finally,this review concludes with a critical assessment of the achievements and challenges encountered in the clinical application of these materials,and proposes practical strategies to address current limitations and guide future research perspectives.
基金Funded by the Natural Science Foundation of Hubei Province(No.2024AFB833)。
文摘Silica fibers were modified by a specific ratio of SiB6 mixed with silica sol through vacuum impregnation method.The modified fibers were then incorporated into a phenolic resin matrix to prepare fiber-reinforced resin composites.The influences of the SiB_(6)/SiO_(2)mixed modification on silica fiber properties were analyzed through thermogravimetric analysis(TGA),differential scanning calorimetry(DSC),scanning electron microscopy(SEM),and X-ray diffraction(XRD),respectively.Additionally,the influence of the SiB_(6)/SiO_(2)mixed modification on the mechanical properties of phenolic resin matrix composites was evaluated through mechanical testing.The experimeatal results indicate that the SiB_(6)/SiO_(2)mixed surface modification shows significant improvement in strength at room temperature and high temperatures,and crystallization temperature of silica fiber increases.The SiB_(6)/Silica sol co-modified silica fiber shows potential for future application in thermal protection and other high-temperature conditions.
基金financially supported by the National Natural Science Foundation of China under the Grant No.22209075。
文摘Single crystalline nickel rich Li[Ni_(x)Co_(y)Mn_(1-x–y)]O_(2)(SCNCM)layered oxide cathodes show higher ionic conductivity and better structure integrity than polycrystalline NCM(PCNCM)cathodes by eliminating grain boundaries.However,it remains challenges in the controlled synthesis process and restricted cycling stability of SCNCM.Herein,take single crystalline nickel rich Li[Ni_(0.8)Co_(0.1)Mn_(0.1)]O_(2)(SC811)as an example,a dual molten salts(LiOH and Li_(2)SO_(4))assisted secondary calcination method is proposed,for which LiOH salt improves primary crystal size and Li_(2)SO_(4)prevents the aggravation of NCM nanocrystals.To further reduce the interfacial side reactions,Mg-doping and B-coating surface modification was carried out,which effectively suppress anisotropic lattice changes and Li/Ni disorder.In addition,a thin and uniform H_(3)BO_(3)coating effectively prevents direct contact between the electrode and electrolyte,thus reducing harmful parasitic reactions.The single crystal structure engineering and surface modification strategy of oxide layered cathodes significantly improve the cycling stability of the modified SC811 cathode.For example,during a long-term cycling of 470 cycles,a high-capacity retention of 74.2%obtained at 1C rate.Our work provides a new strategy for engineering high energy nickel rich layered oxide NCM cathodes.
基金supported by the National Research Foundation of Korea(NRF)grant funded by the Korea government(MSIT)(No.2021R1A2C1007400)supported,partly,by the National R&D Program through the National Research Foundation of Korea(NRF)funded by the Ministry of Science and ICT(Nos.NRF-2020M3H4A3106383,NRF2020M3H4A3081764)+1 种基金supported,partly,by ETRI(No.21YB1610)supported by a Korea Institute for Advancement of Technology(KIAT)grant funded by the Korea Government(MOTIE)(No.P0008458,HRD Program for Industrial Innovation)。
文摘Four types of submicron Ag-coated Cu particles with different Ag contents were prepared as sintering paste fillers,and the Ag contents of the particles were measured to be 10,20,30,and 40 wt.%.Four types of particles(in order of increasing Ag content:A10,A20,A30,and A40)were surface-modified with stearic acid,to suppress the Ag shell dewetting and improve sinterability.The surface-modified particles were mixed with a polyol-based solvent to fabricate a resin-free paste.Subsequently,the pastes were screen-printed onto a slide glass and sintered at 250°C in a nitrogen atmosphere for 1-10 min to form an electrode.The electrical resistivity of the sintered film as a function of sintering time was measured using a four-point probe.All the four surface-modified Cu@Ag particles with different Ag contents exhibited decreased electrical resistivity.Particularly,the largest difference in values after and before the surface modification was observed for A40 with the highest Ag content;the electrical resistivities of the initial and surface-modified particles were 1.51×10^(-4) and 6.67×10^(-5)Ω·cm,respectively,after sintering for 10 min.The findings of this study confirmed that the surface modification using stearic acid effectively suppressed the dewetting of the Ag shell and improved the sinterability of the submicron Cu@Ag particles.
文摘In this paper,the stability of the results of ultrasonic wood surface modification after long-term storage,including macroscopic properties and microstructure of specimens,was investigated.Specimens of aspen wood(Populus tremula)were processed by the developed ultrasonic method of wood surface modification in three different treatment modes and the surface hardness of the specimens was evaluated after processing and after storing the specimens for more than 5 years since long-term stability is an important factor for the use of ultrasonically modified sawn timber as construction and finishing materials.The obtained results of surface hardness measurements by the Leeb method showed that the decrease in hardness after long-term storage is approximately 6.6%for the lowest degree of treatment and approximately 3.4%and 2.4%for medium and high degrees of treatment,taking into account the fact of the average increase in surface hardness approximately 2–4 times,this decrease is insignificant.The internal structure of the specimens after storage was studied by scanning electron microscope(SEM),and deformations of the wood surface layer without damage or rupture were analyzed.The derived stable results confirm the potential of the ultrasonic method for wood surface modification.
基金financially supported by the Science and Technology Commission of Shanghai Municipality(No.24ZR1401400)Shenzhen Salus Bio Med Company for their strong support in this study。
文摘In this study,an amine-reactive poly(pentafluorophenyl acrylate)(PPFPA)platform was developed for advanced surface engineering of next-generation sequencing(NGS)chips.Through post-polymerization modification,PPFPA was functionalized with dual moieties:azide groups for covalent immobilization of DBCO-modified DNA primers via click chemistry and tunable hydrophilic side chains to optimize biocompatibility and surface properties.Systematic screening revealed that hydrophobic azide carriers combined with neutral hydroxyl groups maximized the DNA immobilization efficacy,approaching the performance of commercial polyacrylamide-based polymers.The negatively charged carboxyl groups severely impede DNA primer attachment.Higher molecular weight derivatives further enhance the efficacy of DNA immobilization.In NGS validation,optimized surface modification polymers achieved robust surface density of clustered DNA and high sequencing accuracy,surpassing quality benchmarks and comparable to those of conventional analogs.This platform demonstrates significant potential for tailoring high-sensitivity surfaces for genomic applications,advancing clinical diagnostics,and personalized medicine.
基金supported by the research studentship of The Hong Kong Polytechnic University(Project code:RMAN)the Research and Innovation Office of The Hong Kong Polytechnic University(Project codes:1-W308 and 1-BECE)+2 种基金the Research Grants Council of the Government of the Hong Kong Special Administrative Region(HKSAR),China(No.15205423)funding support from the Innovation and Technology Commission(ITC)of HKSAR,China(MHP/151/22)funding support from the State Key Laboratory of Ultra-precision Machining Technology(Project code:BBX5).
文摘Silicon carbide(SiC)is a highly valued material for power semiconductor devices due to its wide bandgap,high thermal conductivity,and high breakdown electric field.However,its high hardness,brittleness,and chemical stability present substantial challenges for efficient and high-quality processing.This study investigated the effects of picosecond laser surface scanning on 4H-SiC to enhance the material removal performance.The research focused on surface morphology,phase transitions,subsurface/interface characteristics,and material removal mechanisms under varying laser parameters.The results demonstrate that the laser thermal effect decomposes 4H-SiC into amorphous silicon(a-Si),disordered carbon,and graphite,forming a resolidified layer containing Si-O and Si-C-O oxides.Crystalline silicon(c-Si)is produced under high fluences or extensive irradiations.The variation in the resolidified layer thickness with changing laser parameters is revealed.A detailed laser-induced subsurface damage model is developed,encompassing a resolidified layer that includes the above decomposition and oxidation products,and a deformed layer formed primarily under laser-induced stress.The presence of the resolidified layer and the deformed layer leads to a decreased elastic recovery rate and an increased scratching depth,exceeding 2.5 times that of the unmodified condition.Enhanced material removal performance is mainly driven by the resolidified layer at low fluence and by the deformed layer at high fluence.When aligning the total of the ablation depth and the resolidified layer thickness with the subsurface damage depth in the original material,excellent polishing performance is achieved.These findings provide critical insights for understanding the phase evolution,subsurface damage mechanisms,and material removal behavior of 4H-SiC,offering valuable guidance for optimizing the laser surface modification parameters to achieve high-efficiency processing.
基金the financial support from National Natural Science Foundation of China(Nos.22078125 and 52004102)Postdoctoral Science Foundation of China(No.2023M741472)。
文摘Surface modification of fabrics is an effective way to endow them with antifouling properties while still maintaining their key advantages such as comfort,softness and stretchability.Herein,an atmospheric pressure dielectric barrier discharge(DBD)plasma method is demonstrated for the processing of silk fabrics using 1H,1H,2H,2H-perfluorodecyltriethoxysilane(PFDS)as the precursor.The results showed the successful grafting of PFDS groups onto the surface of silk fabrics without causing damage.Meanwhile,the gas temperature is rather low during the whole processing procedure,suggesting the non-equilibrium characteristics of DBD plasma.The influence on fabrics of the processing parameters(PFDS concentration,plasma treatment time and plasma discharge power)was systematically investigated.An optimum processing condition was determined to be a PFDS concentration of 8wt%,a plasma processing time of 40 s and a plasma power of 11.87 W.However,with prolonged plasma processing time or enhanced plasma power,the plasma-grafted PFDS films could be degraded.Further study revealed that plasma processing of silk fabrics with PFDS would lead to a change in their chemical composition and surface roughness.As a result,the surface energy of the fabrics was reduced,accompanied by improved water and oil repellency as well as enhanced antifouling performance.Besides,the plasma-grafted PFDS films also had good durability and stability.By extending the method to polyester and wool against different oil-/water-based stains,the DBD plasma surface modification technique demonstrated good versatility in improving the antifouling properties of fabrics.This work provides guidance for the surface modification of fabrics using DBD plasma to confer them with desirable functionalities.
基金supported by the National Key Research and Development Program of China(Nos.2022YFA1205602,and 2023YFC3707801)the National Natural Science Foundation of China(Nos.U22A20402,22376073,21936003 and 22306119)China Postdoctoral Science Foundation(No.2023T160419).
文摘Nano zero-valent iron(nZVI)is a promising phosphate adsorbent for advanced phosphate removal.However,the rapid passivation of nZVI and the low activity of adsorption sites seriously limit its phosphate removal performance,accounting for its inapplicability to meet the emission criteria of 0.1 mg P/L phosphate.In this study,we report that the oxalate modification can inhibit the passivation of nZVI and alter the multi-stage phosphate adsorption mechanism by changing the adsorption sites.As expected,the stronger antipassivation ability of oxalate modified nZVI(OX-nZVI)strongly favored its phosphate adsorption.Interestingly,the oxalate modification endowed the surface Fe(III)sites with the lowest chemisorption energy and the fastest phosphate adsorption ability than the other adsorption sites,by in situ forming a Fe(III)-phosphate-oxalate ternary complex,therefore enabling an advanced phosphate removal process.At an initial phosphate concentration of 1.00 mg P/L,pH of 6.0 and a dosage of 0.3 g/L of adsorbents,OX-nZVI exhibited faster phosphate removal rate(0.11 g/mg/min)and lower residual phosphate level(0.02 mg P/L)than nZVI(0.055 g/mg/min and 0.19 mg P/L).This study sheds light on the importance of site manipulation in the development of high-performance adsorbents,and offers a facile surface modification strategy to prepare superior iron-basedmaterials for advanced phosphate removal.
基金supported by the National Natural Science Foundation of China(22078132,22108103,and U22A20413)the Open Funding Project of the National Key Labora-tory of Biochemical Engineering(2021KF-02)+3 种基金China Postdoctoral Science Foundation(2021M691301)Jiangsu Key Research and Development Program(BE2022356)the Postdoctoral Fellowship Program of China Postdoctoral Science Foundation(CPSF)(GZ20230989)Jiangsu Agricultural Independent Innovation Fund Project(CX(21)3079).
文摘Expanding the specific surface area of substrates and carrying out precise surface engineering of imprinted nanocavities are crucial methods for enhancing the identification efficiency of molecularly imprinted polymers(MIPs).To implement this synergistic strategy,bioinspired surface engineering was used to incorporate dual covalent receptors via precise post-imprinting modifications(PIMs)onto mesoporous silica nanosheets.The prepared sorbents(denoted as‘‘D-PMIPs”)were utilized to improve the specific identification of adenosine 5-monophosphate(AMP).Significantly,the mesoporous silica nanosheets possess a high surface area of approximately 498.73 m^(2)·g^(-1),which facilitates the formation of abundant specific recognition sites in the D-PMIPs.The dual covalent receptors are valuable for estab-lishing the spatial orientation and arrangement of AMP through multiple cooperative interactions.PIMs enable precise site-specific functionalization within the imprinted cavities,leading to the tailor-made formation of complementary binding sites.The maximum number of high-affinity binding sites(Nmax)of the D-PMIPs is 39.99 lmol·g^(-1),which is significantly higher than that of imprinted sorbents with a sin-gle receptor(i.e.,S-BMIPs or S-PMIPs).The kinetic data of the D-PMIPs can be effectively described by a pseudo-second-order model,indicating that the main binding mechanism involves synergistic chemisorption from boronate affinity and the pyrimidine base.This study suggests that using dual cova-lent receptors and PIMs is a reliable approach for creating imprinted sorbents with high selectivity,allow-ing for the controlled engineering of imprinted sites.
文摘The surface and interfacial properties of polymeric bonding agents and nitramine crystal fillers were studied. The surface free energy and adhesion work of polymeric bonding agents and nitramine fillers were calculated by using Kaeble′s equations. It was observed that the hydroxyl values of neutral polymeric bonding agents (NPBA) correlate well with the polar components of surface free energies. On the basis of the measurements of swelling ratio and initial modulus, the interfacial bonding through highly crosslinked polymeric shell formation around the nitramine particles and generating interfacial reinforcement were rationalized. The application of Tapping Mode AFM (atomic force micro scope) to observing the surface morphology of NPBA reveals that methyl acrylate monomer appears to play a role for aiding the formation of network like structure when nanometer scale images of NPBA are created.
基金Projects(51101177,51401040,51171146,51171216) supported by the National Natural Science Foundation of ChinaProject(CSTC2012JJA245) supported by the Natural Science Foundation of Chongqing,China
文摘A Cu-25Cr alloy prepared by vacuum induction melting method was treated by the high current pulsed electron beam （HCPEB） with pulse numbers ranging from 1 to 100. Surface morphologies and microstructures of the alloy before and after the treatment were investigated by scanning electron microscopy and X-ray diffraction. The results show that significant surface modification can be induced by HCPEB with the pulse number reaching 10. Craters with typical morphologies on the Cu-25Cr alloy surface are formed due to the dynamic thermal field induced by the HCPEB. Micro-cracks, as a unique feature, are well revealed in the irradiated Cu-25Cr specimens and attributed to quasi-static thermal stresses accumulated along the specimen surface. The amount of cracks is found to increase with the pulse number and a preference of these cracks to Cr phases rather than Cu phases is also noted. Another characteristic produced by the HCPEB is the fine Cr spheroids, which are determined to be due to occurrence of liquid phase separation in the Cu-25Cr alloy. In addition, an examination on surface roughness of all specimens reveals that more pulses will produce a roughened surface, as a result of compromising the above features.
