The large-scale production of high-Ti steels is limited by the formation of Ti-containing oxides or nitrides in steel-slag reactions during continuous casting.These processes degrade mold flux properties,clog submerge...The large-scale production of high-Ti steels is limited by the formation of Ti-containing oxides or nitrides in steel-slag reactions during continuous casting.These processes degrade mold flux properties,clog submerged entry nozzles,form floaters in the molds,and produce various surface defects on the cast slabs.This review summarizes the effects of nonmetallic inclusions on traditional CaO-SiO_(2)-based(CS)mold fluxes and novel CaO-Al_(2)O_(3)-based(CA)low-or non-reactive fluxes containing TiO_(2),BaO,and B_(2)O_(3)additives to avoid undesirable steel,slag,and inclusion reactions,with the aim of providing a new perspective for research and practice related to balancing the lubrication and heat transfer of mold fluxes to promote smooth operation and reduce surface defects on cast slabs.For traditional CS mold flux,although the addition of solvents such as Na_(2)O,Li_(2)O,and B_(2)O_(3)can enhance flowability,steel-slag reactions persist,limiting the effectiveness of CS mold fluxes in high-Ti steel casting.Low-or non-reactive CA mold fluxes with reduced SiO_(2)content are a research focus,where adding other components can significantly change flux characteristics.Replacing CaO with BaO can lower the melting point and inhibit crystallization,allowing the flux to maintain good flowability at low temperatures.Replacing SiO_(2)with TiO_(2)can stabilize the viscosity and enhance heat transfer.To reduce the environmental impact,fluorides are replaced with components such as TiO_(2),B_(2)O_(3),BaO,Li_(2)O,and Na_(2)O for F-frce mold fluxes with similar lubrication,crystallization,and heat-transfer effects.When TiO_(2)replaces CaF_(2),it stabilizes the viscosity and enhances the heat conductivity,forming CaTiO_(3)and CaSiTiO_(5)phases instead of cuspidine to control crystallization.B_(2)O_(3)lowers the melting point and suppresses crystallization,forming phases such as Ca_(3)B_(2)O_(6)and Ca_(11)Si_(4)B_(2)O_(22).BaO introduces non-bridging oxygen to reduce viscosity and ensure flux flowability at low temperatures.However,further studies are required to determine the optimal mold flux compositions corresponding to the steel grades and the interactions between the various components of the mold flux.In the future,the practical application of new mold fluxes for high-Ti steel will become the focus of further verification to achieve a balance between lubrication and heat transfer,which is expected to minimize the occurrence of casting problems and slab defects.展开更多
Laser powder bed fusion(LPBF)is highly suitable for forming 18Ni300 mold steel,thanks to its excellent capability in manufacturing complex shapes and outstanding capacity for regulating microstructures.It is widely us...Laser powder bed fusion(LPBF)is highly suitable for forming 18Ni300 mold steel,thanks to its excellent capability in manufacturing complex shapes and outstanding capacity for regulating microstructures.It is widely used in fields such as injection molding,die casting,and stamping dies.Adding reinforcing particles into steel is an effective means to improve its performance.Nb/18Ni300 composites were fabricated by LPBF using two kinds of Nb powders with different particle sizes,and their microstructures and properties were studied.The results show that the unmelted Nb particles are uniformly distributed in the 18Ni300 matrix and the grains are refined,which is particularly pronounced with fine Nb particles.In addition,element diffusion occurs between the particles and the matrix.The main phases of the base alloy are α-Fe and a small amount of γ-Fe.With the addition of Nb,part of the α-Fe is transformed into γ-Fe,and unmelted Nb phases appear.The addition of Nb also enhances the hardness and wear resistance of the composites but slightly reduces their tensile properties.After aging treatment,the molten pools and grain boundaries become blurred,grains are further refined,and the interfaces around the particles are thinned.The aging treatment also promotes the formation of reverted austenite.The hardness,ultimate tensile strength,and volumetric wear rate of the base alloy reach 51.9 HRC,1704 MPa,and 17.8×10^(-6) mm^(3)/(N·m),respectively.In contrast,the sample added with fine Nb particles has the highest hardness(56.1 HRC),ultimate tensile strength(1892 MPa)and yield strength(1842 MPa),and the volume wear rate of the sample added with coarse Nb particles is reduced by 90%to 1.7×10^(-6) mm^(3)/(N·m).展开更多
A full-sectional microstructure characterization method was developed to investigate the formation of coarse slag rims during the continuous casting of hypo-peritectic steel.The cross-sectional microstructural analysi...A full-sectional microstructure characterization method was developed to investigate the formation of coarse slag rims during the continuous casting of hypo-peritectic steel.The cross-sectional microstructural analysis of typical slag rims for two highly crystalline powders revealed that their formation was primarily driven by the solidification of the liquid slag.Distinct differences were observed in the microstructures of slag rims from the two powders.Powder A(characterized by a higher breaking temperature and viscosity)displayed alternating lamellar microstructures of coarse and fine phases,with the coarse phases composed of akermanite-gehlenite transition phases.In contrast,powder B(with a lower breaking temperature and viscosity)predominantly comprised regular akermanite-gehlenite crystals interspersed with a certain amount of glassy phases.Numerical simulations of a three-phase fluid flow coupled with heat transfer indicate that slag rim formation correlates with mold oscillation.Solidification of the liquid slag at the slag rim front predominantly occurs during the negative stroke of the mold oscillation.The average heating rate during the ascending stage of the mold reaches approximately 100 K·s^(−1),whereas the average cooling rate during the descending stage attains 400 K·s^(−1).This temperature variation leads to the formation of lamellar microstructures,whereas the ascending stage promotes the formation of coarse structures and thicker slag rims.Based on the powder properties,two distinct formation pathways exist for highly crystalline mold powders.For the powders with a higher breaking temperature,higher viscosity,and narrower solidification range(powder A),coarse microstructures and thicker slag rims were preferentially formed.For powders with lower breaking temperature and viscosity and wider solidification ranges(powder B),the liquid slag resisted rapid solidification,and the extended mushy zone allowed the partial liquid slag to persist at the slag rim front,promoting the formation of a thin slag rim.This study enhances the understanding of slag rim formation in highly crystalline mold powders and provides critical insights into the control of longitudinal surface cracks in hypo-peritectic steel.展开更多
The flow behavior of molten steel in the thin slab mold under high casting speed conditions was investigated,with a focus on the multi-mode continuous casting and rolling mold.A steel-slag two-phase flow model was est...The flow behavior of molten steel in the thin slab mold under high casting speed conditions was investigated,with a focus on the multi-mode continuous casting and rolling mold.A steel-slag two-phase flow model was established using large eddy simulation,the volume of fluid,and magnetohydrodynamics methods through numerical simulation.The maximum flow velocity and wave height at the steel-slag interface within the mold are critical evaluation criteria for analyzing asymmetric flow under varying casting speeds and electromagnetic braking.The results indicate that the asymmetric flows within the mold do not occur synchronously.The severity of the asymmetric flow correlates with the velocity difference across the steel-slag interface.A greater biased flow prolongs the time required to revert to a steady state.When the magnetic field intensity is set to 0.24 T and the magnetic pole position is at 390 mm from the steel-slag interface,this configuration can reduce the velocity of the steel-slag interface,thereby mitigating the asymmetric flow.Additionally,it can diminish the velocity,impact depth,and impact intensity on the narrow face of the jet,thus improving the distribution of velocity and turbulent kinetic energy within the mold.This configuration prolongs the time required for the steel-slag interface to transition from a stable state to its maximum velocity and shortens the time for the interface to return to stability from an unstable state.Moreover,it ensures the positional stability of the steel-slag interface,confining its position within−3 mm.展开更多
In order to investigate the effect of die wall thickness on morphologies of defect band,a stepped mold with a wall thickness of 5 mm,4 mm,3 mm,2 mm,and 1 mm was designed to carry out high pressure die casting experime...In order to investigate the effect of die wall thickness on morphologies of defect band,a stepped mold with a wall thickness of 5 mm,4 mm,3 mm,2 mm,and 1 mm was designed to carry out high pressure die casting experiments with AlSi10 MgMn alloy.For castings with wall thickness of 2-4 mm,the ratio of the mean defect band width(w)and mean grain size(d)in the defect band(w/d)ranges 7-18,while it increases to 24.47 for the 5 mm-thick casting.This difference is related with the filling speed and the distribution of externally solidified crystals(ESCs).The mold flow analysis indicates that the filling speed decreases from 25.41 m·s^(-1)to 11.07 m·s^(-1)when wall thickness increases from 2 mm to 5 mm.Due to the decreasing filling speed along the wall thickness,ESCs gradually diffuse from the center to the defect band,which keep the shear strength in the defect band at a high-level during filling.Meanwhile,the shear strength generated during the filling also decreases as the shear rate drops.Finally,the defect bands in the 5 mm-thick region become widen and indistinct,and the porosity is as high as 5.25%.展开更多
Photodetectors with long detection distances and fast response are important media in constructing a non-contact human-machine interface for the Masterly Internet of Things(MIT).All-inorganic perovskites have excellen...Photodetectors with long detection distances and fast response are important media in constructing a non-contact human-machine interface for the Masterly Internet of Things(MIT).All-inorganic perovskites have excellent optoelectronic performance with high moisture and oxygen resistance,making them one of the promising candidates for high-performance photodetectors,but a simple,low-cost and reliable fabrication technology is urgently needed.Here,a dual-function laser etching method is developed to complete both the lyophilic split-ring structure and electrode patterning.This novel split-ring structure can capture the perovskite precursor droplet efficiently and achieve the uniform and compact deposition of CsPbBr3 films.Furthermore,our devices based on laterally conducting split-ring structured photodetectors possess outstanding performance,including the maximum responsivity of 1.44×105 mA W^(−1),a response time of 150μs in 1.5 kHz and one-unit area<4×10-2 mm2.Based on these split-ring photodetector arrays,we realized three-dimensional gesture detection with up to 100 mm distance detection and up to 600 mm s^(−1) speed detection,for low-cost,integrative,and non-contact human-machine interfaces.Finally,we applied this MIT to wearable and flexible digital gesture recognition watch panel,safe and comfortable central controller integrated on the car screen,and remote control of the robot,demonstrating the broad potential applications.展开更多
Effects of oblique incidence of terahertz waves on the response of planar split-ring resonators are investigated, both experimentally and by simulation. It is found that the incident angle dependent phase delay and co...Effects of oblique incidence of terahertz waves on the response of planar split-ring resonators are investigated, both experimentally and by simulation. It is found that the incident angle dependent phase delay and coupling conditions of neighboring split-ring resonator （SRR） units play important roles and greatly change both the transmission and reflection spectra for the resonant feature of linear charge oscillations. Our results show that the SRR structure-supported magne- toelectric couplings at oblique excitation are trivial and can be ignored. A highly symmetric response is found in the cross-polarization effects, which may manifest the bianisotropic properties of the SRR system but this needs further study.展开更多
To use the single split-ring resonator （SRR） as a basic unit cell for small antenna with multi-band frequency response is proposed. The structure of antenna is consisted of a single spilt-ring resonator and a couple...To use the single split-ring resonator （SRR） as a basic unit cell for small antenna with multi-band frequency response is proposed. The structure of antenna is consisted of a single spilt-ring resonator and a coupled microstrip line. The designed antenna is numerically optimized with CST Microwave Studio. The radiation properties of the antenna show that there are three frequency bands among which two bands are 1.3 GHz and 2.1 GHz ultra-widehand （UWB）, respectively, where Sll is less than - 10 dB. The gain at every frequency for the multi-hand antenna is above 2.6 dBi, and it increases monotonously with the frequency in the two UWB.展开更多
Novel band-stop filters with circular split-ring resonators based on the metal-insulator-metal （MIM） structure are presented, with their transmission properties of SPPs propagating through the filter simulated by th...Novel band-stop filters with circular split-ring resonators based on the metal-insulator-metal （MIM） structure are presented, with their transmission properties of SPPs propagating through the filter simulated by the finite-difference time-domain （FDTD） method, The variation of the gap of the split ring can affect the transmission characteristics, i.e., the transmission spectrum of SPPs exhibiting a shift, which is useful for modulating the filter. Linear and nonlinear media are used in the resonator respectively. By varying the refractive index of the linear medium, the transmission properties can be changed obviously, and the effect caused by changing the incident intensity with a nonlinear medium is similar. Several resonant modes that are applicable can be enhanced by changing the position of the gap of the split ring. Thus, the transmission properties can be modulated by adjusting the size of the gap, varying the refractive index, and changing the incident intensity of the input light. These methods may play significant roles in applications of optical integrated circuits and nanostructural devices.展开更多
The residual stresses in the wall of a SUS304 stainless steel cylindrical drawing cup were evaluated by split-ring tests, and the influences of stamping die parame- ters on the residual stress were investigated. A new...The residual stresses in the wall of a SUS304 stainless steel cylindrical drawing cup were evaluated by split-ring tests, and the influences of stamping die parame- ters on the residual stress were investigated. A new theoretical model of a split-ring test was developed to evaluate the resid- ual stress in a ring, which was verified to be reasonable and reliable by numerical simulations with ABAQUS code and by nanoindentation tests. Seven groups of split-ring tests were completed, and the residual stresses were calculated according to the theoretical model. The split-ring test results showed that the circumferential residual stress in the wall of the SUS304 stainless steel cylindrical drawing cup was very large and did not change with the different die comer radius. The circumferential residual stress first increased with the increase of drawing punch-die clearance, then was almost unchanged when the clearance increased greater than blank thickness 1 mm. Thus, a smaller clearance was suggested to be chosen to reduce the residual stress in the wall of the SUS304 stainless steel drawing cup.展开更多
An effective approach to expand the bandwidth of negative permeability of small-sized planax materials is proposed. Based on qualitative analysis of equivalent circuit models, the fractional bandwidth of an μ-negati...An effective approach to expand the bandwidth of negative permeability of small-sized planax materials is proposed. Based on qualitative analysis of equivalent circuit models, the fractional bandwidth of an μ-negative （MNG） material is expanded from 3.53% up to 12.87% by adding split-ring resonators （SRRs） and arranging them by proposed steps. Moreover, the experimental results validate the effectiveness of bandwidth-expanding methods, which is promising for the extensive application of metamaterials in the microwave field.展开更多
Metamaterial one-dimensional periodic structures are composed of split-ring resonators, which can display electric permittivity and magnetic permeability simultaneously negative, are studied experimentally. In the pre...Metamaterial one-dimensional periodic structures are composed of split-ring resonators, which can display electric permittivity and magnetic permeability simultaneously negative, are studied experimentally. In the present study, each resonator is made up of two concentric circular copper rings patterned on a substrate of kapton, with slits diametrically opposite each other and with the line of the splits along the longitudinal direction of the periodic array containing seven split rings evenly spaced. The experiments consist in inserting the metamaterial slab into a square waveguide of side length 6 mm, corresponding to a cutoff frequency of 25 GHz. Transmission bands due to magnetic and electrical responses are identified for slits with aperture widths of 1 mm and 2 mm, centered at 5.67 and 6.12 GHz frequencies, respectively, values well below the 25 GHz frequency cutoff, so characterizing a medium with negative permeability and permittivity.展开更多
During the continuous casting process of high-Mn high-Al steels,various types of gases such as Ar need to escape through the top of the mold.In which,the behavior of bubbles traversing the liquid slag serves as a rest...During the continuous casting process of high-Mn high-Al steels,various types of gases such as Ar need to escape through the top of the mold.In which,the behavior of bubbles traversing the liquid slag serves as a restrictive link,closely associated with viscosity and the thickness of liquid slag.In contrast to two-dimensional surface observation,three-dimensional(3D)analysis method can offer a more intuitive,accurate,and comprehensive information.Therefore,this study employs a 3D X-ray microscope(3D-XRM)to obtained spatial distribution and 3D morphological characteristics of residual bubbles in mold flux under different basicity of liquid slag,different temperatures,and different holding times.The results indicate that as basicity of slag increases from 0.52 to 1.03,temperature increases from 1423 to 1573 K,the viscosity of slag decreases,the floating rate of bubbles increases.In addition,when holding time increases from 10 to 30 s,the bubbles floating distance increases,and the volume fraction and average equivalent sphere diameter of the bubbles solidified in the mold flux gradually decreases.In one word,increasing the basicity,temperature,and holding time leading to an increase in the removal rate of bubbles especially for the large.These findings of bubbles escape behavior provide valuable insights into optimizing low basicity mold flux for high-Mn high-Al steels.展开更多
基金financially supported by the National Natural Science Foundation of China(Nos.52204345 and 52474361)the Scientific Research Innovation Projects of Graduate Student of Jiangsu province,China(No.KYCX24_4184)。
文摘The large-scale production of high-Ti steels is limited by the formation of Ti-containing oxides or nitrides in steel-slag reactions during continuous casting.These processes degrade mold flux properties,clog submerged entry nozzles,form floaters in the molds,and produce various surface defects on the cast slabs.This review summarizes the effects of nonmetallic inclusions on traditional CaO-SiO_(2)-based(CS)mold fluxes and novel CaO-Al_(2)O_(3)-based(CA)low-or non-reactive fluxes containing TiO_(2),BaO,and B_(2)O_(3)additives to avoid undesirable steel,slag,and inclusion reactions,with the aim of providing a new perspective for research and practice related to balancing the lubrication and heat transfer of mold fluxes to promote smooth operation and reduce surface defects on cast slabs.For traditional CS mold flux,although the addition of solvents such as Na_(2)O,Li_(2)O,and B_(2)O_(3)can enhance flowability,steel-slag reactions persist,limiting the effectiveness of CS mold fluxes in high-Ti steel casting.Low-or non-reactive CA mold fluxes with reduced SiO_(2)content are a research focus,where adding other components can significantly change flux characteristics.Replacing CaO with BaO can lower the melting point and inhibit crystallization,allowing the flux to maintain good flowability at low temperatures.Replacing SiO_(2)with TiO_(2)can stabilize the viscosity and enhance heat transfer.To reduce the environmental impact,fluorides are replaced with components such as TiO_(2),B_(2)O_(3),BaO,Li_(2)O,and Na_(2)O for F-frce mold fluxes with similar lubrication,crystallization,and heat-transfer effects.When TiO_(2)replaces CaF_(2),it stabilizes the viscosity and enhances the heat conductivity,forming CaTiO_(3)and CaSiTiO_(5)phases instead of cuspidine to control crystallization.B_(2)O_(3)lowers the melting point and suppresses crystallization,forming phases such as Ca_(3)B_(2)O_(6)and Ca_(11)Si_(4)B_(2)O_(22).BaO introduces non-bridging oxygen to reduce viscosity and ensure flux flowability at low temperatures.However,further studies are required to determine the optimal mold flux compositions corresponding to the steel grades and the interactions between the various components of the mold flux.In the future,the practical application of new mold fluxes for high-Ti steel will become the focus of further verification to achieve a balance between lubrication and heat transfer,which is expected to minimize the occurrence of casting problems and slab defects.
基金Key-Area Research and Development Program of Guangdong Province(2023B0909020004)Project of Innovation Research Team in Zhongshan(CXTD2023006)+1 种基金Natural Science Foundation of Guangdong Province(2023A1515011573)Zhongshan Social Welfare Science and Technology Research Project(2024B2022)。
文摘Laser powder bed fusion(LPBF)is highly suitable for forming 18Ni300 mold steel,thanks to its excellent capability in manufacturing complex shapes and outstanding capacity for regulating microstructures.It is widely used in fields such as injection molding,die casting,and stamping dies.Adding reinforcing particles into steel is an effective means to improve its performance.Nb/18Ni300 composites were fabricated by LPBF using two kinds of Nb powders with different particle sizes,and their microstructures and properties were studied.The results show that the unmelted Nb particles are uniformly distributed in the 18Ni300 matrix and the grains are refined,which is particularly pronounced with fine Nb particles.In addition,element diffusion occurs between the particles and the matrix.The main phases of the base alloy are α-Fe and a small amount of γ-Fe.With the addition of Nb,part of the α-Fe is transformed into γ-Fe,and unmelted Nb phases appear.The addition of Nb also enhances the hardness and wear resistance of the composites but slightly reduces their tensile properties.After aging treatment,the molten pools and grain boundaries become blurred,grains are further refined,and the interfaces around the particles are thinned.The aging treatment also promotes the formation of reverted austenite.The hardness,ultimate tensile strength,and volumetric wear rate of the base alloy reach 51.9 HRC,1704 MPa,and 17.8×10^(-6) mm^(3)/(N·m),respectively.In contrast,the sample added with fine Nb particles has the highest hardness(56.1 HRC),ultimate tensile strength(1892 MPa)and yield strength(1842 MPa),and the volume wear rate of the sample added with coarse Nb particles is reduced by 90%to 1.7×10^(-6) mm^(3)/(N·m).
基金supported by the National Natural Science Foundation of China(No.52274318).
文摘A full-sectional microstructure characterization method was developed to investigate the formation of coarse slag rims during the continuous casting of hypo-peritectic steel.The cross-sectional microstructural analysis of typical slag rims for two highly crystalline powders revealed that their formation was primarily driven by the solidification of the liquid slag.Distinct differences were observed in the microstructures of slag rims from the two powders.Powder A(characterized by a higher breaking temperature and viscosity)displayed alternating lamellar microstructures of coarse and fine phases,with the coarse phases composed of akermanite-gehlenite transition phases.In contrast,powder B(with a lower breaking temperature and viscosity)predominantly comprised regular akermanite-gehlenite crystals interspersed with a certain amount of glassy phases.Numerical simulations of a three-phase fluid flow coupled with heat transfer indicate that slag rim formation correlates with mold oscillation.Solidification of the liquid slag at the slag rim front predominantly occurs during the negative stroke of the mold oscillation.The average heating rate during the ascending stage of the mold reaches approximately 100 K·s^(−1),whereas the average cooling rate during the descending stage attains 400 K·s^(−1).This temperature variation leads to the formation of lamellar microstructures,whereas the ascending stage promotes the formation of coarse structures and thicker slag rims.Based on the powder properties,two distinct formation pathways exist for highly crystalline mold powders.For the powders with a higher breaking temperature,higher viscosity,and narrower solidification range(powder A),coarse microstructures and thicker slag rims were preferentially formed.For powders with lower breaking temperature and viscosity and wider solidification ranges(powder B),the liquid slag resisted rapid solidification,and the extended mushy zone allowed the partial liquid slag to persist at the slag rim front,promoting the formation of a thin slag rim.This study enhances the understanding of slag rim formation in highly crystalline mold powders and provides critical insights into the control of longitudinal surface cracks in hypo-peritectic steel.
基金support from the National Natural Science Foundation of China(Grant Nos.52174313 and 52304350)thank all members of the Hebei High Quality Steel Continuous Casting Engineering Technology Research Center at North China University of Science and Technology,Tangshan,China.
文摘The flow behavior of molten steel in the thin slab mold under high casting speed conditions was investigated,with a focus on the multi-mode continuous casting and rolling mold.A steel-slag two-phase flow model was established using large eddy simulation,the volume of fluid,and magnetohydrodynamics methods through numerical simulation.The maximum flow velocity and wave height at the steel-slag interface within the mold are critical evaluation criteria for analyzing asymmetric flow under varying casting speeds and electromagnetic braking.The results indicate that the asymmetric flows within the mold do not occur synchronously.The severity of the asymmetric flow correlates with the velocity difference across the steel-slag interface.A greater biased flow prolongs the time required to revert to a steady state.When the magnetic field intensity is set to 0.24 T and the magnetic pole position is at 390 mm from the steel-slag interface,this configuration can reduce the velocity of the steel-slag interface,thereby mitigating the asymmetric flow.Additionally,it can diminish the velocity,impact depth,and impact intensity on the narrow face of the jet,thus improving the distribution of velocity and turbulent kinetic energy within the mold.This configuration prolongs the time required for the steel-slag interface to transition from a stable state to its maximum velocity and shortens the time for the interface to return to stability from an unstable state.Moreover,it ensures the positional stability of the steel-slag interface,confining its position within−3 mm.
基金supported by the National Natural Science Foundation of China(No.52474396 and 52175284)the National Key Research and Development Program of China(Grant No.2022YFB3404201)。
文摘In order to investigate the effect of die wall thickness on morphologies of defect band,a stepped mold with a wall thickness of 5 mm,4 mm,3 mm,2 mm,and 1 mm was designed to carry out high pressure die casting experiments with AlSi10 MgMn alloy.For castings with wall thickness of 2-4 mm,the ratio of the mean defect band width(w)and mean grain size(d)in the defect band(w/d)ranges 7-18,while it increases to 24.47 for the 5 mm-thick casting.This difference is related with the filling speed and the distribution of externally solidified crystals(ESCs).The mold flow analysis indicates that the filling speed decreases from 25.41 m·s^(-1)to 11.07 m·s^(-1)when wall thickness increases from 2 mm to 5 mm.Due to the decreasing filling speed along the wall thickness,ESCs gradually diffuse from the center to the defect band,which keep the shear strength in the defect band at a high-level during filling.Meanwhile,the shear strength generated during the filling also decreases as the shear rate drops.Finally,the defect bands in the 5 mm-thick region become widen and indistinct,and the porosity is as high as 5.25%.
基金support by the Key Research Project of Zhejiang Laboratory(N.O.2021PE0AC02)the National Natural Science Foundation of China(N.O.11674210)the Project of Hetao Shenzhen-Hong Kong Science and Technology Innovation Cooperation Zone(HZQB-KCZYB-2020083).
文摘Photodetectors with long detection distances and fast response are important media in constructing a non-contact human-machine interface for the Masterly Internet of Things(MIT).All-inorganic perovskites have excellent optoelectronic performance with high moisture and oxygen resistance,making them one of the promising candidates for high-performance photodetectors,but a simple,low-cost and reliable fabrication technology is urgently needed.Here,a dual-function laser etching method is developed to complete both the lyophilic split-ring structure and electrode patterning.This novel split-ring structure can capture the perovskite precursor droplet efficiently and achieve the uniform and compact deposition of CsPbBr3 films.Furthermore,our devices based on laterally conducting split-ring structured photodetectors possess outstanding performance,including the maximum responsivity of 1.44×105 mA W^(−1),a response time of 150μs in 1.5 kHz and one-unit area<4×10-2 mm2.Based on these split-ring photodetector arrays,we realized three-dimensional gesture detection with up to 100 mm distance detection and up to 600 mm s^(−1) speed detection,for low-cost,integrative,and non-contact human-machine interfaces.Finally,we applied this MIT to wearable and flexible digital gesture recognition watch panel,safe and comfortable central controller integrated on the car screen,and remote control of the robot,demonstrating the broad potential applications.
基金Project supported by the National Basic Research Program of China(Grant No.2014CB339800)the National Natural Science Foundation of China(Grant Nos.11374358 and 61077082)
文摘Effects of oblique incidence of terahertz waves on the response of planar split-ring resonators are investigated, both experimentally and by simulation. It is found that the incident angle dependent phase delay and coupling conditions of neighboring split-ring resonator （SRR） units play important roles and greatly change both the transmission and reflection spectra for the resonant feature of linear charge oscillations. Our results show that the SRR structure-supported magne- toelectric couplings at oblique excitation are trivial and can be ignored. A highly symmetric response is found in the cross-polarization effects, which may manifest the bianisotropic properties of the SRR system but this needs further study.
基金Sponsored by the BIT Developing Foundation(1070050320726)
文摘To use the single split-ring resonator （SRR） as a basic unit cell for small antenna with multi-band frequency response is proposed. The structure of antenna is consisted of a single spilt-ring resonator and a coupled microstrip line. The designed antenna is numerically optimized with CST Microwave Studio. The radiation properties of the antenna show that there are three frequency bands among which two bands are 1.3 GHz and 2.1 GHz ultra-widehand （UWB）, respectively, where Sll is less than - 10 dB. The gain at every frequency for the multi-hand antenna is above 2.6 dBi, and it increases monotonously with the frequency in the two UWB.
基金supported by the National Natural Science Foundation of China(Grant No.61001018)the Natural Science Foundation of Shandong Province,China(Grant Nos.ZR2011FM009 and ZR2012FM011)+3 种基金the Research Fund of Shandong University of Science and Technology(SDUST),China(Grant No.2010KYJQ103)the SDUST Research Fund,China(Grant No.2012KYTD103)the Shandong Province Higher Educational Science and Technology Program,China(Grant No.J11LG20)the Qingdao Economic&Technical Development Zone Science&Technology Project,China(Grant No.2013-1-64)
文摘Novel band-stop filters with circular split-ring resonators based on the metal-insulator-metal （MIM） structure are presented, with their transmission properties of SPPs propagating through the filter simulated by the finite-difference time-domain （FDTD） method, The variation of the gap of the split ring can affect the transmission characteristics, i.e., the transmission spectrum of SPPs exhibiting a shift, which is useful for modulating the filter. Linear and nonlinear media are used in the resonator respectively. By varying the refractive index of the linear medium, the transmission properties can be changed obviously, and the effect caused by changing the incident intensity with a nonlinear medium is similar. Several resonant modes that are applicable can be enhanced by changing the position of the gap of the split ring. Thus, the transmission properties can be modulated by adjusting the size of the gap, varying the refractive index, and changing the incident intensity of the input light. These methods may play significant roles in applications of optical integrated circuits and nanostructural devices.
基金supported in part by Xiangtan University Doctoral Fund, China (Grant 12QDZ17)the Excellent Youth Program of Education Bureau of Hunan Province, China (Grant 12B124)the Key Program of Hunan Provincial Natural Science Foundation United with Xiangtan, China (Grant 13JJ8005)
文摘The residual stresses in the wall of a SUS304 stainless steel cylindrical drawing cup were evaluated by split-ring tests, and the influences of stamping die parame- ters on the residual stress were investigated. A new theoretical model of a split-ring test was developed to evaluate the resid- ual stress in a ring, which was verified to be reasonable and reliable by numerical simulations with ABAQUS code and by nanoindentation tests. Seven groups of split-ring tests were completed, and the residual stresses were calculated according to the theoretical model. The split-ring test results showed that the circumferential residual stress in the wall of the SUS304 stainless steel cylindrical drawing cup was very large and did not change with the different die comer radius. The circumferential residual stress first increased with the increase of drawing punch-die clearance, then was almost unchanged when the clearance increased greater than blank thickness 1 mm. Thus, a smaller clearance was suggested to be chosen to reduce the residual stress in the wall of the SUS304 stainless steel drawing cup.
基金Project supported partially by the National Natural Science Foundation of China (Grant Nos. 60872034 and 60971029)the New-Century Talent Program of the Education Department of China (Grant No. NCET070154)+1 种基金the National Defense Research Funding (Grant No. ZJ10DZ02111)the Hi-Tech Research and Development Program of China (Grant No. 2009AA01Z231)
文摘An effective approach to expand the bandwidth of negative permeability of small-sized planax materials is proposed. Based on qualitative analysis of equivalent circuit models, the fractional bandwidth of an μ-negative （MNG） material is expanded from 3.53% up to 12.87% by adding split-ring resonators （SRRs） and arranging them by proposed steps. Moreover, the experimental results validate the effectiveness of bandwidth-expanding methods, which is promising for the extensive application of metamaterials in the microwave field.
基金supported by FAPESP(Sao Paulo Research Foundation)and CNPq(National Council for Scientific and Technological Development)in Brazil
文摘Metamaterial one-dimensional periodic structures are composed of split-ring resonators, which can display electric permittivity and magnetic permeability simultaneously negative, are studied experimentally. In the present study, each resonator is made up of two concentric circular copper rings patterned on a substrate of kapton, with slits diametrically opposite each other and with the line of the splits along the longitudinal direction of the periodic array containing seven split rings evenly spaced. The experiments consist in inserting the metamaterial slab into a square waveguide of side length 6 mm, corresponding to a cutoff frequency of 25 GHz. Transmission bands due to magnetic and electrical responses are identified for slits with aperture widths of 1 mm and 2 mm, centered at 5.67 and 6.12 GHz frequencies, respectively, values well below the 25 GHz frequency cutoff, so characterizing a medium with negative permeability and permittivity.
基金financially supported by the National Natural Science Foundation of China(Nos.52274315 and 52374320)the Fundamental Research Funds for the Central Universities(Nos.FRF-TP-22-011A1 and FRF-DF22-16)。
文摘During the continuous casting process of high-Mn high-Al steels,various types of gases such as Ar need to escape through the top of the mold.In which,the behavior of bubbles traversing the liquid slag serves as a restrictive link,closely associated with viscosity and the thickness of liquid slag.In contrast to two-dimensional surface observation,three-dimensional(3D)analysis method can offer a more intuitive,accurate,and comprehensive information.Therefore,this study employs a 3D X-ray microscope(3D-XRM)to obtained spatial distribution and 3D morphological characteristics of residual bubbles in mold flux under different basicity of liquid slag,different temperatures,and different holding times.The results indicate that as basicity of slag increases from 0.52 to 1.03,temperature increases from 1423 to 1573 K,the viscosity of slag decreases,the floating rate of bubbles increases.In addition,when holding time increases from 10 to 30 s,the bubbles floating distance increases,and the volume fraction and average equivalent sphere diameter of the bubbles solidified in the mold flux gradually decreases.In one word,increasing the basicity,temperature,and holding time leading to an increase in the removal rate of bubbles especially for the large.These findings of bubbles escape behavior provide valuable insights into optimizing low basicity mold flux for high-Mn high-Al steels.
