m thin-film fully-depleted SOI CMOS devices with elevated source/drain structure are fabricated by a novel technology.Key process technologies are demonstrated.The devices have quasi-ideal subthreshold properties;the ...m thin-film fully-depleted SOI CMOS devices with elevated source/drain structure are fabricated by a novel technology.Key process technologies are demonstrated.The devices have quasi-ideal subthreshold properties;the subthreshold slope of nMOSFETs is 65mV/decade,while that of pMOSFETs is 69mV/decade.The saturation current of 1.2μm nMOSFETs is increased by 32% with elevated source/drain structure,and that of 1.2μm pMOSFETs is increased by 24%.The per-stage propagation delay of 101-stage fully-depleted SOI CMOS ring oscillator is 75ps with 3V supply voltage.展开更多
In vertical channel transistors(VCTs),source/drain ion implantation(I/I)represents a significant technical challenge due to inherent three-dimensional structural constraints,which induce complications such as difficul...In vertical channel transistors(VCTs),source/drain ion implantation(I/I)represents a significant technical challenge due to inherent three-dimensional structural constraints,which induce complications such as difficulties in dummy gate forma-tion and shadowing effects of I/I.This article systematically investigates the impact of different implantation conditions on the performance of VCTs with and without dummy gates through TCAD simulation.It reveals the significant role of the lightly doped regions(LDRs)naturally formed due to ion implantation in source/drain of VCTs.Furthermore,it was found that VCT with-out dummy gates can achieve an approximately 27%increase in on-state current(Ion)under the same implantation conditions,and can greatly simplify the process flow and reduce costs.Finally,N-type and P-type VCTs were successfully fabricated using this implantation method.展开更多
Site engineering seismic survey provides basic data for seismic effect analysis. As an important parameter of soil, shear-wave velocity is usually obtained through wave velocity testing in borehole. In this paper, the...Site engineering seismic survey provides basic data for seismic effect analysis. As an important parameter of soil, shear-wave velocity is usually obtained through wave velocity testing in borehole. In this paper, the passive source surface-wave method is introduced into the site engineering seismic survey and practically applied in an engineering site of Shijingshan District. By recording the ubiquitous weak vibration on the earth surface, extract the dispersion curve from the surface-wave components using the SPAC method and obtain the shear-wave velocity structure from inversion. Over the depth of 42 m under- ground, it totally consists of five layers with interface depth of 3.31, 4.50, 7.23, 17.41, and 42.00 m; and shear-wave velocity of 144.0, 198.3, 339.4, 744.2, and 903.7 m/s, respectively. The inversion result is used to evaluate site classification, determine the maximum shear modulus of soil, provide basis for further seismic hazard analysis and site assessment or site zoning, etc. The result shows that the passive source surface-wave method is feasible in the site engineering seismic survey and can replace boreholes,shorten survey period, and reduce engineering cost to some extent.展开更多
Aiming for the restoration of degraded ecosystems, many ecological engineering projects have been implemented around the world. This study investigates the ecological engineering project effectiveness on vegetation re...Aiming for the restoration of degraded ecosystems, many ecological engineering projects have been implemented around the world. This study investigates the ecological engineering project effectiveness on vegetation restoration in the Beijing-Tianjin Sand Source Region(BTSSR) from 2000 to 2010 based on the rain use efficiency(RUE) trend in relation to the land cover. More than half of the BTSSR experienced a vegetation productivity increase from 2000 to 2010, with the increasing intensity being sensitive to the indicators chosen. A clear tendency towards smaller increasing areas was shown when using the net primary productivity(NPP, 51.30%) instead of the accumulated normalized difference vegetation index(59.30%). The short-term variation in the precipitation and intra-seasonal precipitation distribution had a great impact on the remote sensing-based vegetation productivity. However, the residual trends method(RESTREND) effectively eliminated this correlation, while incorporating the variance and skewness of the precipitation distribution increased the models′ ability to explain the vegetation productivity variation. The RUE combined with land cover dynamics was valid for the effectiveness assessment of the ecological engineering projects on vegetation restoration. Particularly, the result based on growing season accumulated normalized difference vegetation index(ΣNDVI) residuals was the most effective, showing that 47.39% of the BTSSR experienced vegetation restoration from 2000 to 2010. The effectiveness of the ecological engineering projects differed for each subarea and was proportional to the strength of ecological engineering. The water erosion region dominated by woodland showed the best restoration, followed by the wind-water erosion crisscross regions, while the wind erosion regions dominated by grassland showed the worst effect. Seriously degraded regions still cover more area in the BTSSR than restored regions. Therefore, more future effort should be put in restoring degraded land.展开更多
This research describes a quantitative,rapid,and low-cost methodology for debris flow susceptibility evaluation at the basin scale using open-access data and geodatabases.The proposed approach can aid decision makers ...This research describes a quantitative,rapid,and low-cost methodology for debris flow susceptibility evaluation at the basin scale using open-access data and geodatabases.The proposed approach can aid decision makers in land management and territorial planning,by first screening for areas with a higher debris flow susceptibility.Five environmental predisposing factors,namely,bedrock lithology,fracture network,quaternary deposits,slope inclination,and hydrographic network,were selected as independent parameters and their mutual interactions were described and quantified using the Rock Engineering System(RES)methodology.For each parameter,specific indexes were proposed,aiming to provide a final synthetic and representative index of debris flow susceptibility at the basin scale.The methodology was tested in four basins located in the Upper Susa Valley(NW Italian Alps)where debris flow events are the predominant natural hazard.The proposed matrix can represent a useful standardized tool,universally applicable,since it is independent of type and characteristic of the basin.展开更多
Engine noise source identification is essential for making noise reduction strategies.Predominant noise sources of engines are normally identified as some cover components such as oil pan, valve cover and front gear c...Engine noise source identification is essential for making noise reduction strategies.Predominant noise sources of engines are normally identified as some cover components such as oil pan, valve cover and front gear cover etc. The radiated noise sources of a 6-cylinder construction diesel engine are identified with two methods-lead covering technique and surface vibration technique,and the ranking of the major cover on the basis of acoustic power is presented in this paper. Firstly the sound power level of these cover components and their contributions to the total acoustic power are determined with lead covering method under hemi-anechoic condition. Then the vibration characteristics of these components are investigated. The sound power level of various components is predicted via the mean square area average vibration. Both results basically agree well and verify the effectiveness of both techniques in engineering field.展开更多
The knowledge representation mode and inference control strategy were analyzed according to the specialties of air-conditioning cooling/heating sources selection. The constructing idea and working procedure for knowle...The knowledge representation mode and inference control strategy were analyzed according to the specialties of air-conditioning cooling/heating sources selection. The constructing idea and working procedure for knowledge base and inference engine were proposed while the realization technique of the C language was discussed. An intelligent decision support system (IDSS) model based on such knowledge representation and inference mechanism was developed by domain engineers. The model was verified to have a small kernel and powerful capability in list processing and data driving, which was successfully used in the design of a cooling/heating sources system for a large-sized office building.展开更多
Violent axial vibration of a vehicle engine crankshaft might lead to multiple defects to the engine.Much research on mechanism and control measures has been done on engines,such as using the dynamic stiffness matrix m...Violent axial vibration of a vehicle engine crankshaft might lead to multiple defects to the engine.Much research on mechanism and control measures has been done on engines,such as using the dynamic stiffness matrix method,rayleigh differential method,and system matrix method.But the source of axial vibration has not been identified clearly because there are many excitation factors for the axial vibration of a crankshaft,such as coupled torsional-axial vibration and coupled bending-axial vibration,etc.In order to improve the calculation reliability and identify the excitation source of axial vibration of in vehicle engine crankshafts,this paper presents a method to identify the axial vibration excitation source of crankshafts for high speed diesel engines based on an auto-regressive and moving average（ARMA） model.Through determining initial moving average variables and measuring axial /bending/torsional vibrations of a crankshaft at the free-end of a 4-cylinder diesel engine,autoregressive spectrum analysis is applied to the measured vibration signal.The results show that the axial vibration of the crankshaft is mainly excited by coupled bending vibration at high speed.But at low speed,the axial vibration in some frequencies is excited primarily by torsional excitation.Through investigation of axial vibration source of engine crankshafts,calculation accuracy of vibration can be improved significantly.展开更多
The effects of source-drain underlaps on the performance of a top gate silicon nanowire on insulator transistor are studied using a three dimensional(3D) self-consistent Poisson-Schrodinger quantum simulation. Voltage...The effects of source-drain underlaps on the performance of a top gate silicon nanowire on insulator transistor are studied using a three dimensional(3D) self-consistent Poisson-Schrodinger quantum simulation. Voltage-controlled tunnel barrier is the device transport physics. The off current, the on/off current ratio, and the inverse subthreshold slope are improved while the on current is degraded with underlap. The physics behind this behavior is the modulation of a tunnel barrier with underlap. The underlap primarily affects the tunneling component of drain current. About 50% contribution to the gate capacitance comes from the fringing electric fields emanating from the gate metal to the source and drain. The gate capacitance reduces with underlap, which should reduce the intrinsic switching delay and increase the intrinsic cut-off frequency. However, both the on current and the transconductance reduce with underlap, and the consequence is the increase of delay and the reduction of cut-off frequency.展开更多
Ge complementary tunneling field-effect transistors（TFETs） are fabricated with the NiGe metal source/drain（S/D） structure. The dopant segregation method is employed to form the NiGe/Ge tunneling junctions of suffi...Ge complementary tunneling field-effect transistors（TFETs） are fabricated with the NiGe metal source/drain（S/D） structure. The dopant segregation method is employed to form the NiGe/Ge tunneling junctions of sufficiently high Schottky barrier heights. As a result, the Ge p-and n-TFETs exhibit decent electrical properties of large ON-state current and steep sub-threshold slope（S factor）. Especially, I_d of 0.2 μA/μm is revealed at V_g-V_（th） = V_d = ±0.5 V for Ge pTFETs,with the S factor of 28 mV/dec at 7 K.展开更多
Fin field-effect transistor(FinFET)technology has been introduced to the mainstream complementary metal-oxide semiconductor(CMOS)manufacturing for low-power and highperformance applications.However,advanced FinFET nod...Fin field-effect transistor(FinFET)technology has been introduced to the mainstream complementary metal-oxide semiconductor(CMOS)manufacturing for low-power and highperformance applications.However,advanced FinFET nodes are facing significant challenges to enhance the device performance due to the increasingly prominent parasitic resistance and capacitance.In this study,for the first time,we demonstrate methods of enhancing p-channel FinFET(pFET)performance on a fully integrated advanced FinFET platform via source/drain(S/D)cavity structure optimization.By modulating the cavity depth and proximity around the optimal reference point,we show that the trade-off between the S/D resistance and short channel effect,as well as the impact on the parasitic capacitance must be considered for the S/D cavity structure optimization.An extra process knob of applying cavity implant on the desired cavity structure was also demonstrated to modify the S/D junction profile for device performance enhancement.展开更多
In this paper, we propose a novel Schottky barrier MOSFET structure, in which the silicide source/drain is designed on the buried metal （SSDOM）. The source/drain region consists of two layers of silicide materials. ...In this paper, we propose a novel Schottky barrier MOSFET structure, in which the silicide source/drain is designed on the buried metal （SSDOM）. The source/drain region consists of two layers of silicide materials. Two Schottky barriers are formed between the silicide layers and the silicon channel. In the device design, the top barrier is lower and the bottom is higher. The lower top contact barrier is to provide higher on-state current, and the higher bottom contact barrier to reduce the off-state current. To achieve this, ErSi is proposed for the top silicide and CoSi2 for the bottom in the n-channel ease. The 50 nm n-channel SSDOM is thus simulated to analyse the performance of the SSDOM device. In the simulations, the top contact barrier is 0.2e V （for ErSi） and the bottom barrier is 0.6 eV （for CoSi2）. Compared with the corresponding conventional Schottky barrier MOSFET structures （CSB）, the high on-state current of the SSDOM is maintained, and the off-state current is efficiently reduced. Thus, the high drive ability （1.2 mA/μm at Vds = 1 V, Vgs = 2 V） and the high Ion/Imin ratio （10^6） are both achieved by applying the SSDOM structure.展开更多
A new modified Angelov current–voltage characteristic model equation is proposed to improve the drain–source current（Ids） simulation of an Al Ga N/Ga N-based（gallium nitride） high electron mobility transistor（A...A new modified Angelov current–voltage characteristic model equation is proposed to improve the drain–source current（Ids） simulation of an Al Ga N/Ga N-based（gallium nitride） high electron mobility transistor（Al Ga N/Ga N-based HEMT） at high power operation. Since an accurate radio frequency（RF） current simulation is critical for a correct power simulation of the device, in this paper we propose a method of Al Ga N/Ga N high electron mobility transistor（HEMT）nonlinear large-signal model extraction with a supplemental modeling of RF drain–source current as a function of RF input power. The improved results of simulated output power, gain, and power added efficiency（PAE） at class-AB quiescent bias of Vgs =-3.5 V, Vds= 30 V with a frequency of 9.6 GHz are presented.展开更多
Pharmaceuticals and personal care products(PPCPs)are receiving attention as emerging pollutants due to their extensive applications and persistent emissions.The Qiantang River Basin,a representative region in eastern ...Pharmaceuticals and personal care products(PPCPs)are receiving attention as emerging pollutants due to their extensive applications and persistent emissions.The Qiantang River Basin,a representative region in eastern China that relies on surface water for drinking purposes,experiences the movement and accumulation of PPCPs in its water and sediment,which can directly affect the safety of drinking water in the basin.This study focuses on the Qiantang River Basin’s surface water,sediment,and drinking water to determine the occurrence and potential risks of 31 PPCPs.It aims to address whether PPCPs in the environment could migrate and accumulate,thereby affecting human health.The findings indicated that PPCPs are ubiquitous in various environmental media,with surface and pore water showing distinct spatial distribution characteristics,specifically,concentrations escalated with urban scale expansion,indicating that domestic sewage discharge is the primary source of PPCP input.Bisphenol A(BPA),ketoprofen(KTP),and diethyltoluamide(DEET)were the primary contaminants.The movement of PPCPs within the surface water-sediment-pore water system was affected by various circumstances.Substances like Sulfamethoxazole(SMX)(RQ>103)and KTP(RQ=22.3)present in surface water and sediment pose significant ecological concerns,and KTP and atrazine(ATZ)(0.6<RQ<2.1)also pose a high risk in drinking water.This study performed an extensive analysis of the distribution and risks associated with typical PPCPs in the Qiantang River Basin,offering a scientific foundation and theoretical support for research on the environmental behavior of PPCPs in this area and the development of targeted pollution control strategies.展开更多
We investigate the influence of source and drain bias voltages(V_(DS))on the quantum sub-band transport spectrum in the 10-nm width N-typed junctionless nanowire transistor at the low temperature of 6 K.We demonstrate...We investigate the influence of source and drain bias voltages(V_(DS))on the quantum sub-band transport spectrum in the 10-nm width N-typed junctionless nanowire transistor at the low temperature of 6 K.We demonstrate that the transverse electric field introduced from V_(DS) has a minor influence on the threshold voltage of the device.The transverse electric field plays the role of amplifying the gate restriction effect of the channel.The one-dimensional(1D)-band dominated transport is demonstrated to be modulated by V_(DS) in the saturation region and the linear region,with the sub-band energy levels in the channel(E_(channel))intersecting with Fermi levels of the source(E_(fS))and the drain(E_(fD))in turn as V_(g) increases.The turning points from the linear region to the saturation region shift to higher gate voltages with V_(DS) increase because the higher Fermi energy levels of the channel required to meet the situation of E_(fD)=E_(channel).We also find that the bias electric field has the effect to accelerate the thermally activated electrons in the channel,equivalent to the effect of thermal temperature on the increase of electron energy.Our work provides a detailed description of the bias-modulated quantum electronic properties,which will give a more comprehensive understanding of transport behavior in nanoscale devices.展开更多
In order to reduce the noise and vibration of the diesel engine,it is crucial to exactly identify the engine noise source character.Based on "two-microphone" method,the sound intensity measurement of a vehic...In order to reduce the noise and vibration of the diesel engine,it is crucial to exactly identify the engine noise source character.Based on "two-microphone" method,the sound intensity measurement of a vehicle four-stroke diesel engine was carried out in a hemi-anechoic chamber.Then the sound intensity contour maps were obtained from the measurement results and the main noise components of different frequencies on all the measurement surfaces were picked out to construct contour maps.By analysizing the relationship between the characteristics of contour maps and the space distribution of the engine compartment,the major sources of the exterior radiation noise of the diesel engine were identified.The results provided a creditable basis for improving the noise performance of the engine in the next phase.展开更多
In this paper, a surface potential based threshold voltage model of fully-depleted（FD） recessed-source/drain（Re-S/D）silicon-on-insulator（SOI） metal-oxide semiconductor field-effect transistor（MOSFET） is presen...In this paper, a surface potential based threshold voltage model of fully-depleted（FD） recessed-source/drain（Re-S/D）silicon-on-insulator（SOI） metal-oxide semiconductor field-effect transistor（MOSFET） is presented while considering the effects of high-k gate-dielectric material induced fringing-field. The two-dimensional（2D） Poisson＇s equation is solved in a channel region in order to obtain the surface potential under the assumption of the parabolic potential profile in the transverse direction of the channel with appropriate boundary conditions. The accuracy of the model is verified by comparing the model＇s results with the 2D simulation results from ATLAS over a wide range of channel lengths and other parameters,including the dielectric constant of gate-dielectric material.展开更多
Based on the foreign remanufacturing mode,which relies mainly on Part-Replacing Repair Method and Size-Changing Repair Method,China has explored and practiced the new remanufacturing mode,which relies mainly on Surfac...Based on the foreign remanufacturing mode,which relies mainly on Part-Replacing Repair Method and Size-Changing Repair Method,China has explored and practiced the new remanufacturing mode,which relies mainly on Surface Repair and Performance Improving Method.The aim of remanufacturing forming is to renew rapidly the original size of the waste components rapidly,and then improve their service performance.The advanced surface engineering technology,especially the high density heat source surface forming technology,is the important technique to carry out rapid forming.Based on the arc heat source,plasma heat source and laser heat source,three kinds of high density heat source remanufacturing forming technologies,such as high speed arc spraying forming technology,micro-arc plasma forming technology,and laser cladding forming technology,have been developed.The benefits of remanufacturing forming based on advanced surface engineering technologies are great.展开更多
Elastic wave on seafloor caused by low frequency noise radiated from ship is called ship seismic wave which can be used to identify ship target. In order to analyze the wave components and the propagating properties o...Elastic wave on seafloor caused by low frequency noise radiated from ship is called ship seismic wave which can be used to identify ship target. In order to analyze the wave components and the propagating properties of ship seismic wave, the numerical calculation of synthetic seismograms on seafloor aroused by a low frequency point sound source is carried out using a wave number integration technique combined with inverse Fourier transform. According to the numerical example of hard seafloor, the time series of seismic wave on seafloor are mostly composed of interface waves and normal mode waves. Each normal mode wave has a well defined low cut-off frequency, while the interface wave doesn't have. The frequency dispersion of normal mode wave is obvious when frequency is lower than 100Hz, while the interface wave is dispersive only in the infra-sound frequency range. The time series of seismic wave is dominated by the interface wave when the source frequency is less than the minimal cut-off frequency of normal mode wave.展开更多
Acoustic signals from diesel engines contain useful information but also include considerable noise components To extract information for condition monitoring purposes, continuous wavelet transform (CWT) is used for t...Acoustic signals from diesel engines contain useful information but also include considerable noise components To extract information for condition monitoring purposes, continuous wavelet transform (CWT) is used for the characterization of engine acoustics. This paper first reviews CWT characteristics represented by short duration transient signals. Wavelet selection and CWT are then implemented and wavelet transform is used to analyze the major sources of the engine front's exterior radiation sound. The research provides a reliable basis for engineering practice to reduce vehicle sound level. Comparison of the identification results of the measured acoustic signals with the identification results of the measured surface vibration showed good agreement.展开更多
文摘m thin-film fully-depleted SOI CMOS devices with elevated source/drain structure are fabricated by a novel technology.Key process technologies are demonstrated.The devices have quasi-ideal subthreshold properties;the subthreshold slope of nMOSFETs is 65mV/decade,while that of pMOSFETs is 69mV/decade.The saturation current of 1.2μm nMOSFETs is increased by 32% with elevated source/drain structure,and that of 1.2μm pMOSFETs is increased by 24%.The per-stage propagation delay of 101-stage fully-depleted SOI CMOS ring oscillator is 75ps with 3V supply voltage.
文摘In vertical channel transistors(VCTs),source/drain ion implantation(I/I)represents a significant technical challenge due to inherent three-dimensional structural constraints,which induce complications such as difficulties in dummy gate forma-tion and shadowing effects of I/I.This article systematically investigates the impact of different implantation conditions on the performance of VCTs with and without dummy gates through TCAD simulation.It reveals the significant role of the lightly doped regions(LDRs)naturally formed due to ion implantation in source/drain of VCTs.Furthermore,it was found that VCT with-out dummy gates can achieve an approximately 27%increase in on-state current(Ion)under the same implantation conditions,and can greatly simplify the process flow and reduce costs.Finally,N-type and P-type VCTs were successfully fabricated using this implantation method.
基金supported by National Natural Science Foundation of China (No. 41174085)Chinese Academy of Sciences (KZZD-EW-TZ-19)China Geological Survey (12120113101400)
文摘Site engineering seismic survey provides basic data for seismic effect analysis. As an important parameter of soil, shear-wave velocity is usually obtained through wave velocity testing in borehole. In this paper, the passive source surface-wave method is introduced into the site engineering seismic survey and practically applied in an engineering site of Shijingshan District. By recording the ubiquitous weak vibration on the earth surface, extract the dispersion curve from the surface-wave components using the SPAC method and obtain the shear-wave velocity structure from inversion. Over the depth of 42 m under- ground, it totally consists of five layers with interface depth of 3.31, 4.50, 7.23, 17.41, and 42.00 m; and shear-wave velocity of 144.0, 198.3, 339.4, 744.2, and 903.7 m/s, respectively. The inversion result is used to evaluate site classification, determine the maximum shear modulus of soil, provide basis for further seismic hazard analysis and site assessment or site zoning, etc. The result shows that the passive source surface-wave method is feasible in the site engineering seismic survey and can replace boreholes,shorten survey period, and reduce engineering cost to some extent.
基金Under the auspices of National Natural Science Foundation of China(No.41571421)National Science and Technology Major Project of China(No.21-Y30B05-9001-13/15)
文摘Aiming for the restoration of degraded ecosystems, many ecological engineering projects have been implemented around the world. This study investigates the ecological engineering project effectiveness on vegetation restoration in the Beijing-Tianjin Sand Source Region(BTSSR) from 2000 to 2010 based on the rain use efficiency(RUE) trend in relation to the land cover. More than half of the BTSSR experienced a vegetation productivity increase from 2000 to 2010, with the increasing intensity being sensitive to the indicators chosen. A clear tendency towards smaller increasing areas was shown when using the net primary productivity(NPP, 51.30%) instead of the accumulated normalized difference vegetation index(59.30%). The short-term variation in the precipitation and intra-seasonal precipitation distribution had a great impact on the remote sensing-based vegetation productivity. However, the residual trends method(RESTREND) effectively eliminated this correlation, while incorporating the variance and skewness of the precipitation distribution increased the models′ ability to explain the vegetation productivity variation. The RUE combined with land cover dynamics was valid for the effectiveness assessment of the ecological engineering projects on vegetation restoration. Particularly, the result based on growing season accumulated normalized difference vegetation index(ΣNDVI) residuals was the most effective, showing that 47.39% of the BTSSR experienced vegetation restoration from 2000 to 2010. The effectiveness of the ecological engineering projects differed for each subarea and was proportional to the strength of ecological engineering. The water erosion region dominated by woodland showed the best restoration, followed by the wind-water erosion crisscross regions, while the wind erosion regions dominated by grassland showed the worst effect. Seriously degraded regions still cover more area in the BTSSR than restored regions. Therefore, more future effort should be put in restoring degraded land.
文摘This research describes a quantitative,rapid,and low-cost methodology for debris flow susceptibility evaluation at the basin scale using open-access data and geodatabases.The proposed approach can aid decision makers in land management and territorial planning,by first screening for areas with a higher debris flow susceptibility.Five environmental predisposing factors,namely,bedrock lithology,fracture network,quaternary deposits,slope inclination,and hydrographic network,were selected as independent parameters and their mutual interactions were described and quantified using the Rock Engineering System(RES)methodology.For each parameter,specific indexes were proposed,aiming to provide a final synthetic and representative index of debris flow susceptibility at the basin scale.The methodology was tested in four basins located in the Upper Susa Valley(NW Italian Alps)where debris flow events are the predominant natural hazard.The proposed matrix can represent a useful standardized tool,universally applicable,since it is independent of type and characteristic of the basin.
文摘Engine noise source identification is essential for making noise reduction strategies.Predominant noise sources of engines are normally identified as some cover components such as oil pan, valve cover and front gear cover etc. The radiated noise sources of a 6-cylinder construction diesel engine are identified with two methods-lead covering technique and surface vibration technique,and the ranking of the major cover on the basis of acoustic power is presented in this paper. Firstly the sound power level of these cover components and their contributions to the total acoustic power are determined with lead covering method under hemi-anechoic condition. Then the vibration characteristics of these components are investigated. The sound power level of various components is predicted via the mean square area average vibration. Both results basically agree well and verify the effectiveness of both techniques in engineering field.
文摘The knowledge representation mode and inference control strategy were analyzed according to the specialties of air-conditioning cooling/heating sources selection. The constructing idea and working procedure for knowledge base and inference engine were proposed while the realization technique of the C language was discussed. An intelligent decision support system (IDSS) model based on such knowledge representation and inference mechanism was developed by domain engineers. The model was verified to have a small kernel and powerful capability in list processing and data driving, which was successfully used in the design of a cooling/heating sources system for a large-sized office building.
基金supported by National Natural Science Foundation of China (Grant No. 509060605)China Postdoctoral Science Foundation (Grant No. 201003295)
文摘Violent axial vibration of a vehicle engine crankshaft might lead to multiple defects to the engine.Much research on mechanism and control measures has been done on engines,such as using the dynamic stiffness matrix method,rayleigh differential method,and system matrix method.But the source of axial vibration has not been identified clearly because there are many excitation factors for the axial vibration of a crankshaft,such as coupled torsional-axial vibration and coupled bending-axial vibration,etc.In order to improve the calculation reliability and identify the excitation source of axial vibration of in vehicle engine crankshafts,this paper presents a method to identify the axial vibration excitation source of crankshafts for high speed diesel engines based on an auto-regressive and moving average（ARMA） model.Through determining initial moving average variables and measuring axial /bending/torsional vibrations of a crankshaft at the free-end of a 4-cylinder diesel engine,autoregressive spectrum analysis is applied to the measured vibration signal.The results show that the axial vibration of the crankshaft is mainly excited by coupled bending vibration at high speed.But at low speed,the axial vibration in some frequencies is excited primarily by torsional excitation.Through investigation of axial vibration source of engine crankshafts,calculation accuracy of vibration can be improved significantly.
文摘The effects of source-drain underlaps on the performance of a top gate silicon nanowire on insulator transistor are studied using a three dimensional(3D) self-consistent Poisson-Schrodinger quantum simulation. Voltage-controlled tunnel barrier is the device transport physics. The off current, the on/off current ratio, and the inverse subthreshold slope are improved while the on current is degraded with underlap. The physics behind this behavior is the modulation of a tunnel barrier with underlap. The underlap primarily affects the tunneling component of drain current. About 50% contribution to the gate capacitance comes from the fringing electric fields emanating from the gate metal to the source and drain. The gate capacitance reduces with underlap, which should reduce the intrinsic switching delay and increase the intrinsic cut-off frequency. However, both the on current and the transconductance reduce with underlap, and the consequence is the increase of delay and the reduction of cut-off frequency.
基金Supported by the National Natural Science Foundation of China under Grant No 61504120the Zhejiang Provincial Natural Science Foundation of China under Grant No LR18F040001the Fundamental Research Funds for the Central Universities
文摘Ge complementary tunneling field-effect transistors（TFETs） are fabricated with the NiGe metal source/drain（S/D） structure. The dopant segregation method is employed to form the NiGe/Ge tunneling junctions of sufficiently high Schottky barrier heights. As a result, the Ge p-and n-TFETs exhibit decent electrical properties of large ON-state current and steep sub-threshold slope（S factor）. Especially, I_d of 0.2 μA/μm is revealed at V_g-V_（th） = V_d = ±0.5 V for Ge pTFETs,with the S factor of 28 mV/dec at 7 K.
文摘Fin field-effect transistor(FinFET)technology has been introduced to the mainstream complementary metal-oxide semiconductor(CMOS)manufacturing for low-power and highperformance applications.However,advanced FinFET nodes are facing significant challenges to enhance the device performance due to the increasingly prominent parasitic resistance and capacitance.In this study,for the first time,we demonstrate methods of enhancing p-channel FinFET(pFET)performance on a fully integrated advanced FinFET platform via source/drain(S/D)cavity structure optimization.By modulating the cavity depth and proximity around the optimal reference point,we show that the trade-off between the S/D resistance and short channel effect,as well as the impact on the parasitic capacitance must be considered for the S/D cavity structure optimization.An extra process knob of applying cavity implant on the desired cavity structure was also demonstrated to modify the S/D junction profile for device performance enhancement.
基金Project supported by the National Natural Science Foundation of China （Grant No 60506009）.
文摘In this paper, we propose a novel Schottky barrier MOSFET structure, in which the silicide source/drain is designed on the buried metal （SSDOM）. The source/drain region consists of two layers of silicide materials. Two Schottky barriers are formed between the silicide layers and the silicon channel. In the device design, the top barrier is lower and the bottom is higher. The lower top contact barrier is to provide higher on-state current, and the higher bottom contact barrier to reduce the off-state current. To achieve this, ErSi is proposed for the top silicide and CoSi2 for the bottom in the n-channel ease. The 50 nm n-channel SSDOM is thus simulated to analyse the performance of the SSDOM device. In the simulations, the top contact barrier is 0.2e V （for ErSi） and the bottom barrier is 0.6 eV （for CoSi2）. Compared with the corresponding conventional Schottky barrier MOSFET structures （CSB）, the high on-state current of the SSDOM is maintained, and the off-state current is efficiently reduced. Thus, the high drive ability （1.2 mA/μm at Vds = 1 V, Vgs = 2 V） and the high Ion/Imin ratio （10^6） are both achieved by applying the SSDOM structure.
基金Project supported by the National Natural Science Foundation of China(Grant No.61204086)
文摘A new modified Angelov current–voltage characteristic model equation is proposed to improve the drain–source current（Ids） simulation of an Al Ga N/Ga N-based（gallium nitride） high electron mobility transistor（Al Ga N/Ga N-based HEMT） at high power operation. Since an accurate radio frequency（RF） current simulation is critical for a correct power simulation of the device, in this paper we propose a method of Al Ga N/Ga N high electron mobility transistor（HEMT）nonlinear large-signal model extraction with a supplemental modeling of RF drain–source current as a function of RF input power. The improved results of simulated output power, gain, and power added efficiency（PAE） at class-AB quiescent bias of Vgs =-3.5 V, Vds= 30 V with a frequency of 9.6 GHz are presented.
基金jointly supported by the Open Research Fund of State Environmental Protection Key Laboratory of Drinking Water Source Protection,Chinese Research Academy of Environmental Sciences(2022YYSYKFYB07)the Fundamental Research Funds for the Central Publicinterest Scientific Institution(2022YSKY-07)the China Geological Survey Project(DD20211414).
文摘Pharmaceuticals and personal care products(PPCPs)are receiving attention as emerging pollutants due to their extensive applications and persistent emissions.The Qiantang River Basin,a representative region in eastern China that relies on surface water for drinking purposes,experiences the movement and accumulation of PPCPs in its water and sediment,which can directly affect the safety of drinking water in the basin.This study focuses on the Qiantang River Basin’s surface water,sediment,and drinking water to determine the occurrence and potential risks of 31 PPCPs.It aims to address whether PPCPs in the environment could migrate and accumulate,thereby affecting human health.The findings indicated that PPCPs are ubiquitous in various environmental media,with surface and pore water showing distinct spatial distribution characteristics,specifically,concentrations escalated with urban scale expansion,indicating that domestic sewage discharge is the primary source of PPCP input.Bisphenol A(BPA),ketoprofen(KTP),and diethyltoluamide(DEET)were the primary contaminants.The movement of PPCPs within the surface water-sediment-pore water system was affected by various circumstances.Substances like Sulfamethoxazole(SMX)(RQ>103)and KTP(RQ=22.3)present in surface water and sediment pose significant ecological concerns,and KTP and atrazine(ATZ)(0.6<RQ<2.1)also pose a high risk in drinking water.This study performed an extensive analysis of the distribution and risks associated with typical PPCPs in the Qiantang River Basin,offering a scientific foundation and theoretical support for research on the environmental behavior of PPCPs in this area and the development of targeted pollution control strategies.
基金the National Key Research and Development Program of China(Grant No.2016YFA0200503).
文摘We investigate the influence of source and drain bias voltages(V_(DS))on the quantum sub-band transport spectrum in the 10-nm width N-typed junctionless nanowire transistor at the low temperature of 6 K.We demonstrate that the transverse electric field introduced from V_(DS) has a minor influence on the threshold voltage of the device.The transverse electric field plays the role of amplifying the gate restriction effect of the channel.The one-dimensional(1D)-band dominated transport is demonstrated to be modulated by V_(DS) in the saturation region and the linear region,with the sub-band energy levels in the channel(E_(channel))intersecting with Fermi levels of the source(E_(fS))and the drain(E_(fD))in turn as V_(g) increases.The turning points from the linear region to the saturation region shift to higher gate voltages with V_(DS) increase because the higher Fermi energy levels of the channel required to meet the situation of E_(fD)=E_(channel).We also find that the bias electric field has the effect to accelerate the thermally activated electrons in the channel,equivalent to the effect of thermal temperature on the increase of electron energy.Our work provides a detailed description of the bias-modulated quantum electronic properties,which will give a more comprehensive understanding of transport behavior in nanoscale devices.
基金supported by programfor the Top Young Academic Leaders of Higher Learning Institutions of Shanxi(2009)Natural Science Foundation of Shanxi Province,China(No.2010011031-2)
文摘In order to reduce the noise and vibration of the diesel engine,it is crucial to exactly identify the engine noise source character.Based on "two-microphone" method,the sound intensity measurement of a vehicle four-stroke diesel engine was carried out in a hemi-anechoic chamber.Then the sound intensity contour maps were obtained from the measurement results and the main noise components of different frequencies on all the measurement surfaces were picked out to construct contour maps.By analysizing the relationship between the characteristics of contour maps and the space distribution of the engine compartment,the major sources of the exterior radiation noise of the diesel engine were identified.The results provided a creditable basis for improving the noise performance of the engine in the next phase.
基金supported by the Science and Engineering Research Board(SERB),Department of Science and Technology,Ministry of Human Resource and Development,Government of India under Young Scientist Research(Grant No.SB/FTP/ETA-415/2012)
文摘In this paper, a surface potential based threshold voltage model of fully-depleted（FD） recessed-source/drain（Re-S/D）silicon-on-insulator（SOI） metal-oxide semiconductor field-effect transistor（MOSFET） is presented while considering the effects of high-k gate-dielectric material induced fringing-field. The two-dimensional（2D） Poisson＇s equation is solved in a channel region in order to obtain the surface potential under the assumption of the parabolic potential profile in the transverse direction of the channel with appropriate boundary conditions. The accuracy of the model is verified by comparing the model＇s results with the 2D simulation results from ATLAS over a wide range of channel lengths and other parameters,including the dielectric constant of gate-dielectric material.
文摘Based on the foreign remanufacturing mode,which relies mainly on Part-Replacing Repair Method and Size-Changing Repair Method,China has explored and practiced the new remanufacturing mode,which relies mainly on Surface Repair and Performance Improving Method.The aim of remanufacturing forming is to renew rapidly the original size of the waste components rapidly,and then improve their service performance.The advanced surface engineering technology,especially the high density heat source surface forming technology,is the important technique to carry out rapid forming.Based on the arc heat source,plasma heat source and laser heat source,three kinds of high density heat source remanufacturing forming technologies,such as high speed arc spraying forming technology,micro-arc plasma forming technology,and laser cladding forming technology,have been developed.The benefits of remanufacturing forming based on advanced surface engineering technologies are great.
基金Sponsored by National Nature Science Foundation of China ( 51179195)National Defense Foundation of China ( 513030203-02)
文摘Elastic wave on seafloor caused by low frequency noise radiated from ship is called ship seismic wave which can be used to identify ship target. In order to analyze the wave components and the propagating properties of ship seismic wave, the numerical calculation of synthetic seismograms on seafloor aroused by a low frequency point sound source is carried out using a wave number integration technique combined with inverse Fourier transform. According to the numerical example of hard seafloor, the time series of seismic wave on seafloor are mostly composed of interface waves and normal mode waves. Each normal mode wave has a well defined low cut-off frequency, while the interface wave doesn't have. The frequency dispersion of normal mode wave is obvious when frequency is lower than 100Hz, while the interface wave is dispersive only in the infra-sound frequency range. The time series of seismic wave is dominated by the interface wave when the source frequency is less than the minimal cut-off frequency of normal mode wave.
基金Project (No. 50175078) supported by the National Natural Science Foundation of China
文摘Acoustic signals from diesel engines contain useful information but also include considerable noise components To extract information for condition monitoring purposes, continuous wavelet transform (CWT) is used for the characterization of engine acoustics. This paper first reviews CWT characteristics represented by short duration transient signals. Wavelet selection and CWT are then implemented and wavelet transform is used to analyze the major sources of the engine front's exterior radiation sound. The research provides a reliable basis for engineering practice to reduce vehicle sound level. Comparison of the identification results of the measured acoustic signals with the identification results of the measured surface vibration showed good agreement.
