Morphology and growth rate of carbon dioxide hydrate on the interface between liquid carbon dioxide and humic acid solutions were studied in this work.It was found that after the growth of the hydrate film at the inte...Morphology and growth rate of carbon dioxide hydrate on the interface between liquid carbon dioxide and humic acid solutions were studied in this work.It was found that after the growth of the hydrate film at the interface,further growth of hydrate due to the suction of water in the capillary system formed between the wall of the cuvette and the end boundary of the hydrate layer occurs.Most probably,substantial effects on the formation of this capillary system may be caused by variations in reactor wall properties,for example,hydrophobic-hydrophilic balance,roughness,etc.We found,that the rate of CO_(2) hydrate film growth on the surface of the humic acid aqueous solution is 4-fold to lower in comparison with the growth rate on the surface of pure water.We suppose that this is caused by the adsorption of humic acid associates on the surface of hydrate particles and,as a consequence,by the deceleration of the diffusion of dissolved carbon dioxide to the growing hydrate particle.展开更多
Rapid analysis of metal ions and organic compounds in strong acidic solutions is of sustainable interest in multiple disciplines.However,complicated and time-consuming pretreatments are always required for MS analysis...Rapid analysis of metal ions and organic compounds in strong acidic solutions is of sustainable interest in multiple disciplines.However,complicated and time-consuming pretreatments are always required for MS analysis of the compounds in strong acidic solutions.Otherwise,it will result in a weak signal and cause serious damage to the mass spectrometer.Herein,a simple method inherited from nano-ESI MS was developed for rapid analysis of strong acidic solutions.Nanoliter(nL)strong acidic solution was first loaded in the nano-ESI emitter,followed by evaporation to remove the H+and leave the analytes on the wall of the nano-ESI emitter.The evaporation process can be completed within 1 min because of the extremely tiny volume(≤1 nL)of the loaded solution.Then,the dried analytes on the wall of the nano-ESI emitter were redissolved by loading a new solvent,followed by nano-ESI MS analysis.By using this method,metal ions and organic compounds in the strong acidic solution can be detected with low sample consumption(1 nL),high speed(<2 min/sample),high sensitivity(limit of detection=0.2µg/L),and high accuracy(>90%).Proof-of-concept applications of the present method have been successfully achieved for the analysis of gastric juice(pH of the sample=1),monitoring reaction catalyzed by strong acid(pH of the system=0),and micro-area analysis of ores(pH of the extraction solvent=0),showing great application potential in multiple fields.展开更多
Sonoluminescence is more distinctly observed in phosphoric and sulfuric acid,which exhibit high viscosity and lower vapor pressures relative to water.Within an 85-wt%phosphoric acid solution saturated with argon(Ar),v...Sonoluminescence is more distinctly observed in phosphoric and sulfuric acid,which exhibit high viscosity and lower vapor pressures relative to water.Within an 85-wt%phosphoric acid solution saturated with argon(Ar),variations in the light-emitting regimes of bubbles were noted to correspond with increments in the driving acoustic intensity.Specifically,the bubbles were observed to perform a dance-like motion 2 cm below the multi-bubble sonoluminescence(MBSL)cluster,traversing a 25-mm^(2) grid during the camera exposure period.Spectral analysis conducted at the beginning of the experiment showed a gradual attenuation of CN(B^(2)Σ–X^(2)Σ)emission concurrent with a strengthening of Ar(4p–4s)atom emission lines.The application of a theoretical temperature model to the spectral data revealed that the internal temperature of the bubbles escalates swiftly upon their implosion.This study is instrumental in advancing the comprehension of the underlying mechanisms of sonoluminescence and in the formulation of a dynamic model for the behavior of the bubbles.展开更多
The Hastelloy C22 coatings on Q235 steel substrate were produced by high power diode laser cladding technique. Their corrosion behaviors in static and cavitation hydrochloric, sulfuric and nitric acid solutions were i...The Hastelloy C22 coatings on Q235 steel substrate were produced by high power diode laser cladding technique. Their corrosion behaviors in static and cavitation hydrochloric, sulfuric and nitric acid solutions were investigated. The electrochemical results show that corrosion resistance of coatings in static acid solutions is higher than that in cavitation ones. In each case, coating corrosion resistance in descending order is in nitric, sulfuric and hydrochloric acid solutions. Obvious erosion-corrosion morphology and serious intercrystalline corrosion of coating are noticed in cavitation hydrochloric acid solution. This is mainly ascribed to the aggressive ions in hydrochloric acid solution and mechanical effect from cavitation bubbles collapse. While coating after corrosion test in cavitation nitric acid solution shows nearly unchanged surface morphology. The results indicate that the associated action of cavitation and property of acid solution determines the corrosion development of coating. Hastelloy C22 coating exhibits better corrosion resistance in oxidizing acid solution for the stable formation of dense oxide film on the surface.展开更多
In order to improve corrosion resistance of stainless steel 316L in warm acidic solution, Ni？Cu？P coatings with high copper and phosphorus contents were deposited onto stainless steel 316L substrates via electroless...In order to improve corrosion resistance of stainless steel 316L in warm acidic solution, Ni？Cu？P coatings with high copper and phosphorus contents were deposited onto stainless steel 316L substrates via electroless plating. The structure of the film and its resistance to corrosion in a warm acidic environment were investigated using scanning electron microscopy （SEM）, energy dispersive spectroscopy （EDS）, X-ray diffraction spectrometry （XRD）, polarization curves, electrochemical impedance spectroscopy （EIS）, and dipping corrosion tests, respectively. The results demonstrate that Ni？Cu？P coatings consist of two types of nodules, which are 19.98% Cu and 39.17% Cu （mass fraction） respectively. The corrosion resistance of the 316L substrate when subjected to a warm acidic solution is significantly improved by the addition of the new type of the Ni？Cu？P coating. The as-plated coatings demonstrate better corrosion resistance than annealed coatings. As-plated coatings and those annealed at 673 K are found to corrode selectively, while pitting is observed to be the main corrosion mechanism of coatings annealed at 773 and 873 K.展开更多
Important effects exist between precious metals and rare earths oxides in three-way catalyst, especially the coordinated effects. These effects were studied by using H2PtCl6, Pt(NH3)2(NO2)2 and Pt(OH)2(C2H5ONH2)2 as P...Important effects exist between precious metals and rare earths oxides in three-way catalyst, especially the coordinated effects. These effects were studied by using H2PtCl6, Pt(NH3)2(NO2)2 and Pt(OH)2(C2H5ONH2)2 as Pt precursors, and the mixed oxide of (Ce-Zr-La-Pr)O as base material to prepare a series of catalysts, and their performances of the catalysts were studied by TPR and CO pulse titration technologies. The results shown that Pt precursors and their solutions pH values influenced the oxygen storage capabilities, the active metal distribution degrees of the catalysts obviously, and every catalyst prepared by different precursors had an optimal pH values. It indicates that the active metals precursors and their solutions acidities have outstanding influences on the catalysts performances for the mutual effects existing between the active metals and the Rare Earth metal oxides, which results from the mate groups of the precursors and the solution acidity.展开更多
Fluid-rock interaction plays a critical function in physical and chemical processes associated with the formation and evolution of oil and gas reservoir space.In the diagenetic stage of shallow burial,the dissolution ...Fluid-rock interaction plays a critical function in physical and chemical processes associated with the formation and evolution of oil and gas reservoir space.In the diagenetic stage of shallow burial,the dissolution of carbonate rocks by acidic fluids is conducive to the development of secondary pore space in reservoirs.In contrast,the free drift experiment based on water bath instrument can simulate the dissolution process of carbonate rocks in shallow burial environment effectively.In order to study the shallow burial dissolution mechanism of carbonate rocks in different acid solutions,14 samples of typical carbonate rocks of Sinian,Cambrian,Ordovician,Permian and Triassic ages in the Tarim and Sichuan basins,China were used.The dissolution experiments on carbonate rocks in sulfuric acid,acetic acid,hydrochloric acid,silicic acid and carbonic acid at shallow burial temperature(30℃≤T≤90℃)were carried out using a water bath instrument.The PHREEQC software was used to simulate the dissolution of carbonate minerals,in order to compare the results of constant temperature water bath experiment.The results show that acid solutions have significant dissolution effect on shallow burial carbonate rocks when T=50–60℃,which corresponds to the burial depth of 1500–2000 m in the Tarim Basin and 1110–1480 m in the Sichuan Basin.However,there were obvious differences in the dissolution and reformation of carbonate rocks in different acids.In particular,sulfuric acid solution produced by thermochemical sulfate reduction can significantly promote the dissolution of carbonate rocks,especially dolomitic limestone.Moreover,the dissolution of limestone reservoirs is stronger than that of dolomite reservoirs in shallow burial.The results will provide new insights into the study of dissolution laws and influencing factors of reservoir spaces and the evaluation and prediction of carbonate reservoirs in China.展开更多
The behaviour of vanadium（V） extracted from sulfuric acid solution was investigated using Cyanex 923 as an extractant. The effects of the concentration of Cyanex 923 and the pH of the solution were studied. The extr...The behaviour of vanadium（V） extracted from sulfuric acid solution was investigated using Cyanex 923 as an extractant. The effects of the concentration of Cyanex 923 and the pH of the solution were studied. The extraction of vanadium（V） increases with the increase of Cyanex 923 concentration and shaking time. Cyanex 923 can extract vanadium（V） from sulfuric acid solution at low pH conditions, and the best pH conditions for extraction of vanadium（V） are at pH 1.0-2.0. The species extracted into the organic phase is VO2HSO4 with one molecule of Cyanex 923. Equilibrium studies were used to assess the extraction efficiency of vanadium（V） recovery from the sulfuric acid solution.展开更多
The adsorption behavior of ion exchange resin D301 in the extraction of hexavalent molybdenum from high acidic leach solution was investigated. SEM, EDS and Raman spectra analyses were applied to studying the adsorpti...The adsorption behavior of ion exchange resin D301 in the extraction of hexavalent molybdenum from high acidic leach solution was investigated. SEM, EDS and Raman spectra analyses were applied to studying the adsorption capacity, reaction kinetics and possible adsorption mechanism in detail. Results showed that the adsorption capacity of D301 resin for molybdenum from high acidic leach solution was up to 463.63 mg/g. Results of the kinetic analysis indicated that the adsorption process was controlled by the particle diffusion with the activation energy 25.47 k J/mol（0.9-1.2 mm） and 20.38 k J/mol（0.6-0.9 mm）. Furthermore, the molybdenum loaded on the resin could be eluted by using 2 mol/L ammonia hydroxide solution. Besides, dynamic continuous column experiments verified direct extraction of molybdenum from acidic leach solutions by ion exchange resin D301 and the upstream flow improved dynamic continuous absorption.展开更多
Electrochemical corrosion behavior of Nd-Fe-B sintered magnets in nitric acid, hydrochloric acid, sulfuric acid, phosphate acid and in oxalic acid was studied. Potentiodynamic polarization curves and immersion time de...Electrochemical corrosion behavior of Nd-Fe-B sintered magnets in nitric acid, hydrochloric acid, sulfuric acid, phosphate acid and in oxalic acid was studied. Potentiodynamic polarization curves and immersion time dependence of corrosion rates of Nd-Fe-B sintered magnets in different acid solutions were tested. Microstructures of corroded Nd-Fe-B sintered magnets were investigated by means of SEM and AFM. The results indicate that in strong acid solutions of similar hydrogen ion concentration, the corrosion current increases in the order of HCl 〉 H3SO4 〉 HNO3 solution and Nd-Fe-B sintered magnets are passivated in phosphate acid and oxalic acid. Within 25 min, the corrosion rates of Nd-Fe-B sintered magnets in H2SO4 and H3PO4 solutions show a declining trend with immersion time, while in HNO3 and HCl solutions the corrosion rates are rising. And in H2C2O4 solution, weight of the magnets increases. The brim of Nd-Fe-B sintered magnets is corroded rather seriously and the size of the magnets changed greatly in nitric acid. The surfaces of the corroded magnets in the above mentioned acid solutions are all coarse.展开更多
Hydrogen molybdenum bronze (HxMoO3) can be electrodeposited on platinum and oxidized in two steps to the hydrogen molybdenum bronze with less amount of hydrogen HyMoO3 (y<x) and MoO3 when platinum electrode is cycl...Hydrogen molybdenum bronze (HxMoO3) can be electrodeposited on platinum and oxidized in two steps to the hydrogen molybdenum bronze with less amount of hydrogen HyMoO3 (y<x) and MoO3 when platinum electrode is cycled from -0.2 to 1.3V (vs. SCE) in 0.05 mol/L Na2MoO4 + 0.5 mol/L H2SO4 solution. During the formation of HxMoO3, the electrochemical reduction of molybdate existing in the form of polymolydate is reversible and is about a five-electron transfer reaction.展开更多
The dissolution of carbon steel in 5% HCl in the temperature range of 30~90℃ was inhibited by two organic compounds having the general formula: ClR NH2(CH2)n NH2 RCl where R is a benzyl group. The behaviour of these ...The dissolution of carbon steel in 5% HCl in the temperature range of 30~90℃ was inhibited by two organic compounds having the general formula: ClR NH2(CH2)n NH2 RCl where R is a benzyl group. The behaviour of these inhibitors in acidic medium were investigated using weight loss method, open circuit potential and linear polarization technique. These inhibitors provided satisfactory corrosion inhibition for carbon steel in hydrochloric acid solutions even at higher temperature and acid concentration (10%). The electrochemical results showed that the polarization resistance (Rp) values increased with increasing inhibitor concentration, also the corrosion current decreased and a higher inhibition efficiency was obtained. The protective properties of these two organic inhibitors were attributed to the chemisorption mechanism展开更多
The molecular structures of metal precursors in the impregnating solution were designed so as to prepare efficient Ni Mo/Al_2O_3 hydrodesulfurization(HDS) catalysts. At first, five typical impregnating solutions were ...The molecular structures of metal precursors in the impregnating solution were designed so as to prepare efficient Ni Mo/Al_2O_3 hydrodesulfurization(HDS) catalysts. At first, five typical impregnating solutions were designed; the existing metal precursors, such as [Mo4(citrate)2O11]^(4-)-like, [P2Mo18O62]^(6-)-like and [P2Mo5O23]^(6-)-like species in the solutions were confirmed by laser Raman spectroscopy(LRS). The UV-Vis spectra results indicated that the solutions containing both phosphoric acid and citric acid could change the existing form of nickel species. Five corresponding Ni Mo/Al_2O_3 catalysts were prepared by the incipient wetness impregnation method. The LRS analysis results of dried catalysts showed that the above metal precursors could be partly retained on alumina support after impregnation and drying, although the interface reaction between different metal precursors and alumina support unavoidably took place. Then the catalysts were sulfided and characterized by N2 physisorption, TEM and XPS analyses. The results showed that different metal precursors in impregnating solution could mainly result in the difference in both the morphology of(Ni)Mo S2 slabs and the promoting effect of Ni species. The catalyst prepared mainly with [P2Mo5O23]^(6-)-like species used as precursors exhibited worse dispersion of(Ni)Mo S2 slabs and lower ratio of Ni–Mo–S active phases than the one with [Mo4(citrate)2O11]^(4-)-like species. Promisingly, the catalyst prepared with co-existing [Mo4(citrate)2O11]^(4-)-like, [P2Mo18O62]^(6-)-like and [P2Mo5O23]^(6-)-like species showed better hydrodesulfurization activity for 4,6-DMDBT thanks to its more well-dispersed Ni–Mo–S active phases.展开更多
The acid gas absorption in four potassium based amino acid salt solutions was predicted using artificial neural network(ANN). Two hundred fifty-five experimental data points for CO_2 absorption in the four potassium b...The acid gas absorption in four potassium based amino acid salt solutions was predicted using artificial neural network(ANN). Two hundred fifty-five experimental data points for CO_2 absorption in the four potassium based amino acid salt solutions containing potassium lysinate, potassium prolinate, potassium glycinate, and potassium taurate were used in this modeling. Amine salt solution's type, temperature, equilibrium partial pressure of acid gas, the molar concentration of the solution, molecular weight, and the boiling point were considered as inputs to ANN to prognosticate the capacity of amino acid salt solution to absorb acid gas. Regression analysis was employed to assess the performance of the network. Levenberg–Marquardt back-propagation algorithm was used to train the optimal ANN with 5:12:1 architecture. The model findings indicated that the proposed ANN has the capability to predict precisely the absorption of acid gases in various amino acid salt solutions with Mean Square Error(MSE) value of 0.0011, the Average Absolute Relative Deviation(AARD) percent of 5.54%,and the correlation coefficient(R^2) of 0.9828.展开更多
Potentiodynamic polarization tests and slow strain rate test（SSRT） in combination with fracture morphology observations were conducted to investigate the stress corrosion cracking（SCC） behavior of 7003 aluminum al...Potentiodynamic polarization tests and slow strain rate test（SSRT） in combination with fracture morphology observations were conducted to investigate the stress corrosion cracking（SCC） behavior of 7003 aluminum alloy（AA7003） in acid and alkaline chloride solutions under various applied potentials（Ea）. The results show that AA7003 is to a certain extent susceptible to SCC via anodic dissolution（AD） at open-circuit potential（OCP） and is highly susceptible to hydrogen embrittlement（HE） at high negative Ea in the solutions with p H levels of 4 and 11. The susceptibility increases with negative shift in the potential when Ea is less than-1000 m V vs. SCE. However, the susceptibility distinctly decreases because of the inhibition of AD when Ea is equal to-1000 m V vs. SCE. In addition, the SCC susceptibility of AA7003 in the acid chloride solution is higher than that in the alkaline solution at each potential. Moreover, the effect of hydrogen on SCC increases with increasing hydrogen ion concentration.展开更多
The reaction between carbonic acid and montmorillonite minerals was studied in order to provide a theoretical basis for analyzing changes in the physical properties of coal seams after CO_(2)injection and for optimizi...The reaction between carbonic acid and montmorillonite minerals was studied in order to provide a theoretical basis for analyzing changes in the physical properties of coal seams after CO_(2)injection and for optimizing CO_(2) pumping parameters.A single montmorillonite mineral of purity[90%was selected and subjected to reactions at 25,35,and 45℃in carbonic acid solutions of varying acidity.The Si and Al concentrations in the solutions and the structure and elemental compositions of the montmorillonite before and after the reactions were analyzed using a spectrophotometer,an X-ray diffractometer,and an energy-dispersive X-ray spectrometer;kinetic reaction models were established for the dissolution of Si and Al in carbonic acid solutions in order to estimate the apparent activation energy of Si dissolution under different acidity conditions.The results indicate that Al dissolved rapidly and soon reached solubility equilibrium.On the other hand,Si concentration in the solutions increased rapidly and then gradually declined with vibrations,with maximum values at 25,35,and 45℃,which were observed at approximately 96,72,and 48 h,respectively.In addition,Si dissolution fitted the diffusion-controlled reaction model well;as the pH value decreased,the apparent activation energy of Si dissolution decreased,and Si became easier to dissolve.Furthermore,it was concluded that as a weak acid,carbonic acid causes little damage to the mineral structure of montmorillonite.展开更多
The existing form of molybdenum in acidic sulfate solution was studied by means of ion exchange, infrared （IR） spectra and X-ray photoelectron spectroscopy （XPS）. The results indicate that the anionic molybdenum s...The existing form of molybdenum in acidic sulfate solution was studied by means of ion exchange, infrared （IR） spectra and X-ray photoelectron spectroscopy （XPS）. The results indicate that the anionic molybdenum species are predominant in acidic sulfate solution, and Mo（VI） can combine with sulfate radical to form heteropoly acid anions [Mo205（804）2]2- and [MoO2（HSO4）4]2-. With the decrease in solution pH from 1.92 to 0.06, the existing form of Mo（VI） changes from MovO21（OH）3^3- to [Mo205（S04）2]2- and then becomes [MoOz（HSO4）4]2-, which results in the decrease in the resin adsorption capacity for molybdenum.展开更多
The corrosion-wear behavior of a nanocrystalline Fe_（88）Si_（12） alloy disc coupled with a Si_3N_4 ball was investigated in acid（pH 3） and alkaline（pH 9） aqueous solutions. The dry wear was also measured for re...The corrosion-wear behavior of a nanocrystalline Fe_（88）Si_（12） alloy disc coupled with a Si_3N_4 ball was investigated in acid（pH 3） and alkaline（pH 9） aqueous solutions. The dry wear was also measured for reference. The average friction coefficient of Fe_（88）Si_（12） alloy in the pH 9 solution was approximately 0.2, which was lower than those observed for Fe_（88）Si_（12） alloy in the pH 3 solution and in the case of dry wear. The fluctuation of the friction coefficient of samples subjected to the pH 9 solution also showed similar characteristics. The wear rate in the pH 9 solution slightly increased with increasing applied load. The wear rate was approximately one order of magnitude less than that in the pH 3 solution and was far lower than that in the case of dry wear, especially at high applied load. The wear traces of Fe_（88）Si_（12） alloy under different wear conditions were examined and analyzed by scanning electron microscopy, energy-dispersive X-ray spectroscopy, and X-ray photoelectron spectroscopy. The results indicated that the tribo-chemical reactions that involve oxidation of the worn surface and hydrolysis of the Si_3N_4 ball in the acid solution were restricted in the pH 9 aqueous solution. Thus, water lubrication can effectively improve the wear resistance of nanocrystalline Fe_（88）Si_（12） alloy in the pH 9 aqueous solution.展开更多
The electrochemical-voltammetry behavior of vanillin, heliotropin, anisaldehyde on the surface of Pt, Au electrodes in acid solution has been studied by means of the electrochemical cyclic voltammetry method. It was f...The electrochemical-voltammetry behavior of vanillin, heliotropin, anisaldehyde on the surface of Pt, Au electrodes in acid solution has been studied by means of the electrochemical cyclic voltammetry method. It was found that the electrochemical processes of them are irreversible on both Pt and Au electrodes. The electrochemical activity of vanillin is stronger than heliotropin's and heliotropin's is stronger than anisaldehyde's on Pt electrode. While the electrochemical activity of anisaldehyde is stronger than heliotropin's and vanillin's is the weakest on Au. The results indicate that when they are used as additives for electroplating, they must be consumptive, and it will improve the leveling ability of plating solution and brightness of the deposition layer.展开更多
This study addresses the liquid-liquid extraction behavior of phosphorus from a sulfuric acid solution using benzyl dimethyl amine(BDMA)in kerosene.The extraction equilibria investigated with varied BDMA concentration...This study addresses the liquid-liquid extraction behavior of phosphorus from a sulfuric acid solution using benzyl dimethyl amine(BDMA)in kerosene.The extraction equilibria investigated with varied BDMA concentrations could reveal the formation of 3[BDMA]·[H_(3)PO_(4)]^(-)complex in the organic phase.The thermodynamic properties determined at various temperatures indicated that the process was exothermic with a calculated enthalpy(△H^(Θ))of−24.0 kJ·mol^(−1).The organic-to-aqueous phase(O/A)volume ratio was varied to elucidate the quantitative extraction of phosphorus.The McCabe-Thiele diagram plotted for the extraction isotherm was validated for the requirement of three counter-current stages in the extraction at an O/A volume ratio of 2.0/3.5.The back-extraction of phosphorus from the loaded organic phase was quantitatively achieved by contacting 4.0 mol·L−1 H2SO4 solution in three stages of counter-current contact at an O/A volume ratio of 3/2.This study can be applied to remove phosphorus from the sulfuric acid leach solutions of monazite processing,and many other solutions.展开更多
基金supported by the Russian Science Foundation(23-29-00830).
文摘Morphology and growth rate of carbon dioxide hydrate on the interface between liquid carbon dioxide and humic acid solutions were studied in this work.It was found that after the growth of the hydrate film at the interface,further growth of hydrate due to the suction of water in the capillary system formed between the wall of the cuvette and the end boundary of the hydrate layer occurs.Most probably,substantial effects on the formation of this capillary system may be caused by variations in reactor wall properties,for example,hydrophobic-hydrophilic balance,roughness,etc.We found,that the rate of CO_(2) hydrate film growth on the surface of the humic acid aqueous solution is 4-fold to lower in comparison with the growth rate on the surface of pure water.We suppose that this is caused by the adsorption of humic acid associates on the surface of hydrate particles and,as a consequence,by the deceleration of the diffusion of dissolved carbon dioxide to the growing hydrate particle.
基金supported by the National Natural Science Foundation of China(Nos.21864001,21727812 and 21765001)the Ph.D.Start-up Foundation of East China University of Technology(No.DHBK2020001).
文摘Rapid analysis of metal ions and organic compounds in strong acidic solutions is of sustainable interest in multiple disciplines.However,complicated and time-consuming pretreatments are always required for MS analysis of the compounds in strong acidic solutions.Otherwise,it will result in a weak signal and cause serious damage to the mass spectrometer.Herein,a simple method inherited from nano-ESI MS was developed for rapid analysis of strong acidic solutions.Nanoliter(nL)strong acidic solution was first loaded in the nano-ESI emitter,followed by evaporation to remove the H+and leave the analytes on the wall of the nano-ESI emitter.The evaporation process can be completed within 1 min because of the extremely tiny volume(≤1 nL)of the loaded solution.Then,the dried analytes on the wall of the nano-ESI emitter were redissolved by loading a new solvent,followed by nano-ESI MS analysis.By using this method,metal ions and organic compounds in the strong acidic solution can be detected with low sample consumption(1 nL),high speed(<2 min/sample),high sensitivity(limit of detection=0.2µg/L),and high accuracy(>90%).Proof-of-concept applications of the present method have been successfully achieved for the analysis of gastric juice(pH of the sample=1),monitoring reaction catalyzed by strong acid(pH of the system=0),and micro-area analysis of ores(pH of the extraction solvent=0),showing great application potential in multiple fields.
基金Project supported by the Scientific Research Project of Higher Education in the Inner Mongolia Autonomous Region,China(Grant No.NJZY23100)the Natural Science Foundation of Inner Mongolia Autonomous Region,China(Grant No.2024FX30)the 14th Five Year Plan Project for Education Science in Inner Mongolia Autonomous Region,China(Grant No.NGJGH2023205).
文摘Sonoluminescence is more distinctly observed in phosphoric and sulfuric acid,which exhibit high viscosity and lower vapor pressures relative to water.Within an 85-wt%phosphoric acid solution saturated with argon(Ar),variations in the light-emitting regimes of bubbles were noted to correspond with increments in the driving acoustic intensity.Specifically,the bubbles were observed to perform a dance-like motion 2 cm below the multi-bubble sonoluminescence(MBSL)cluster,traversing a 25-mm^(2) grid during the camera exposure period.Spectral analysis conducted at the beginning of the experiment showed a gradual attenuation of CN(B^(2)Σ–X^(2)Σ)emission concurrent with a strengthening of Ar(4p–4s)atom emission lines.The application of a theoretical temperature model to the spectral data revealed that the internal temperature of the bubbles escalates swiftly upon their implosion.This study is instrumental in advancing the comprehension of the underlying mechanisms of sonoluminescence and in the formulation of a dynamic model for the behavior of the bubbles.
文摘The Hastelloy C22 coatings on Q235 steel substrate were produced by high power diode laser cladding technique. Their corrosion behaviors in static and cavitation hydrochloric, sulfuric and nitric acid solutions were investigated. The electrochemical results show that corrosion resistance of coatings in static acid solutions is higher than that in cavitation ones. In each case, coating corrosion resistance in descending order is in nitric, sulfuric and hydrochloric acid solutions. Obvious erosion-corrosion morphology and serious intercrystalline corrosion of coating are noticed in cavitation hydrochloric acid solution. This is mainly ascribed to the aggressive ions in hydrochloric acid solution and mechanical effect from cavitation bubbles collapse. While coating after corrosion test in cavitation nitric acid solution shows nearly unchanged surface morphology. The results indicate that the associated action of cavitation and property of acid solution determines the corrosion development of coating. Hastelloy C22 coating exhibits better corrosion resistance in oxidizing acid solution for the stable formation of dense oxide film on the surface.
基金Project(CKJA201202)supported by the Innovation Fund Key Project of Nanjing Institute of Technology,ChinaProject(51301088)supported by the National Natural Science Foundation of China
文摘In order to improve corrosion resistance of stainless steel 316L in warm acidic solution, Ni？Cu？P coatings with high copper and phosphorus contents were deposited onto stainless steel 316L substrates via electroless plating. The structure of the film and its resistance to corrosion in a warm acidic environment were investigated using scanning electron microscopy （SEM）, energy dispersive spectroscopy （EDS）, X-ray diffraction spectrometry （XRD）, polarization curves, electrochemical impedance spectroscopy （EIS）, and dipping corrosion tests, respectively. The results demonstrate that Ni？Cu？P coatings consist of two types of nodules, which are 19.98% Cu and 39.17% Cu （mass fraction） respectively. The corrosion resistance of the 316L substrate when subjected to a warm acidic solution is significantly improved by the addition of the new type of the Ni？Cu？P coating. The as-plated coatings demonstrate better corrosion resistance than annealed coatings. As-plated coatings and those annealed at 673 K are found to corrode selectively, while pitting is observed to be the main corrosion mechanism of coatings annealed at 773 and 873 K.
基金Project supported by the National High Technology Research and Development Programs (863 ) of China (2002 AA321060, 2004AA649040) Yunnan Province Science Technology Program (2004B0028Q)
文摘Important effects exist between precious metals and rare earths oxides in three-way catalyst, especially the coordinated effects. These effects were studied by using H2PtCl6, Pt(NH3)2(NO2)2 and Pt(OH)2(C2H5ONH2)2 as Pt precursors, and the mixed oxide of (Ce-Zr-La-Pr)O as base material to prepare a series of catalysts, and their performances of the catalysts were studied by TPR and CO pulse titration technologies. The results shown that Pt precursors and their solutions pH values influenced the oxygen storage capabilities, the active metal distribution degrees of the catalysts obviously, and every catalyst prepared by different precursors had an optimal pH values. It indicates that the active metals precursors and their solutions acidities have outstanding influences on the catalysts performances for the mutual effects existing between the active metals and the Rare Earth metal oxides, which results from the mate groups of the precursors and the solution acidity.
基金jointly supported by the Science and Technology Development Project of PetroChina Hangzhou Institute of Petroleum Geology(No.RIPED-2020-JS-51008)the Naturacl Science Foundation of China(Nos.41872250,41802159)。
文摘Fluid-rock interaction plays a critical function in physical and chemical processes associated with the formation and evolution of oil and gas reservoir space.In the diagenetic stage of shallow burial,the dissolution of carbonate rocks by acidic fluids is conducive to the development of secondary pore space in reservoirs.In contrast,the free drift experiment based on water bath instrument can simulate the dissolution process of carbonate rocks in shallow burial environment effectively.In order to study the shallow burial dissolution mechanism of carbonate rocks in different acid solutions,14 samples of typical carbonate rocks of Sinian,Cambrian,Ordovician,Permian and Triassic ages in the Tarim and Sichuan basins,China were used.The dissolution experiments on carbonate rocks in sulfuric acid,acetic acid,hydrochloric acid,silicic acid and carbonic acid at shallow burial temperature(30℃≤T≤90℃)were carried out using a water bath instrument.The PHREEQC software was used to simulate the dissolution of carbonate minerals,in order to compare the results of constant temperature water bath experiment.The results show that acid solutions have significant dissolution effect on shallow burial carbonate rocks when T=50–60℃,which corresponds to the burial depth of 1500–2000 m in the Tarim Basin and 1110–1480 m in the Sichuan Basin.However,there were obvious differences in the dissolution and reformation of carbonate rocks in different acids.In particular,sulfuric acid solution produced by thermochemical sulfate reduction can significantly promote the dissolution of carbonate rocks,especially dolomitic limestone.Moreover,the dissolution of limestone reservoirs is stronger than that of dolomite reservoirs in shallow burial.The results will provide new insights into the study of dissolution laws and influencing factors of reservoir spaces and the evaluation and prediction of carbonate reservoirs in China.
基金supported by the Science Foundation of Central South University (No. 76112037) the Postdoctoral Science Foundation of Central South University
文摘The behaviour of vanadium（V） extracted from sulfuric acid solution was investigated using Cyanex 923 as an extractant. The effects of the concentration of Cyanex 923 and the pH of the solution were studied. The extraction of vanadium（V） increases with the increase of Cyanex 923 concentration and shaking time. Cyanex 923 can extract vanadium（V） from sulfuric acid solution at low pH conditions, and the best pH conditions for extraction of vanadium（V） are at pH 1.0-2.0. The species extracted into the organic phase is VO2HSO4 with one molecule of Cyanex 923. Equilibrium studies were used to assess the extraction efficiency of vanadium（V） recovery from the sulfuric acid solution.
基金Projects(21376251,21406233) supported by the National Natural Science Foundation of China
文摘The adsorption behavior of ion exchange resin D301 in the extraction of hexavalent molybdenum from high acidic leach solution was investigated. SEM, EDS and Raman spectra analyses were applied to studying the adsorption capacity, reaction kinetics and possible adsorption mechanism in detail. Results showed that the adsorption capacity of D301 resin for molybdenum from high acidic leach solution was up to 463.63 mg/g. Results of the kinetic analysis indicated that the adsorption process was controlled by the particle diffusion with the activation energy 25.47 k J/mol（0.9-1.2 mm） and 20.38 k J/mol（0.6-0.9 mm）. Furthermore, the molybdenum loaded on the resin could be eluted by using 2 mol/L ammonia hydroxide solution. Besides, dynamic continuous column experiments verified direct extraction of molybdenum from acidic leach solutions by ion exchange resin D301 and the upstream flow improved dynamic continuous absorption.
文摘Electrochemical corrosion behavior of Nd-Fe-B sintered magnets in nitric acid, hydrochloric acid, sulfuric acid, phosphate acid and in oxalic acid was studied. Potentiodynamic polarization curves and immersion time dependence of corrosion rates of Nd-Fe-B sintered magnets in different acid solutions were tested. Microstructures of corroded Nd-Fe-B sintered magnets were investigated by means of SEM and AFM. The results indicate that in strong acid solutions of similar hydrogen ion concentration, the corrosion current increases in the order of HCl 〉 H3SO4 〉 HNO3 solution and Nd-Fe-B sintered magnets are passivated in phosphate acid and oxalic acid. Within 25 min, the corrosion rates of Nd-Fe-B sintered magnets in H2SO4 and H3PO4 solutions show a declining trend with immersion time, while in HNO3 and HCl solutions the corrosion rates are rising. And in H2C2O4 solution, weight of the magnets increases. The brim of Nd-Fe-B sintered magnets is corroded rather seriously and the size of the magnets changed greatly in nitric acid. The surfaces of the corroded magnets in the above mentioned acid solutions are all coarse.
文摘Hydrogen molybdenum bronze (HxMoO3) can be electrodeposited on platinum and oxidized in two steps to the hydrogen molybdenum bronze with less amount of hydrogen HyMoO3 (y<x) and MoO3 when platinum electrode is cycled from -0.2 to 1.3V (vs. SCE) in 0.05 mol/L Na2MoO4 + 0.5 mol/L H2SO4 solution. During the formation of HxMoO3, the electrochemical reduction of molybdate existing in the form of polymolydate is reversible and is about a five-electron transfer reaction.
文摘The dissolution of carbon steel in 5% HCl in the temperature range of 30~90℃ was inhibited by two organic compounds having the general formula: ClR NH2(CH2)n NH2 RCl where R is a benzyl group. The behaviour of these inhibitors in acidic medium were investigated using weight loss method, open circuit potential and linear polarization technique. These inhibitors provided satisfactory corrosion inhibition for carbon steel in hydrochloric acid solutions even at higher temperature and acid concentration (10%). The electrochemical results showed that the polarization resistance (Rp) values increased with increasing inhibitor concentration, also the corrosion current decreased and a higher inhibition efficiency was obtained. The protective properties of these two organic inhibitors were attributed to the chemisorption mechanism
基金supported by the National Key Basic Research Program of China(973 Program,2012CB224802)the SINOPEC project(No.114013)
文摘The molecular structures of metal precursors in the impregnating solution were designed so as to prepare efficient Ni Mo/Al_2O_3 hydrodesulfurization(HDS) catalysts. At first, five typical impregnating solutions were designed; the existing metal precursors, such as [Mo4(citrate)2O11]^(4-)-like, [P2Mo18O62]^(6-)-like and [P2Mo5O23]^(6-)-like species in the solutions were confirmed by laser Raman spectroscopy(LRS). The UV-Vis spectra results indicated that the solutions containing both phosphoric acid and citric acid could change the existing form of nickel species. Five corresponding Ni Mo/Al_2O_3 catalysts were prepared by the incipient wetness impregnation method. The LRS analysis results of dried catalysts showed that the above metal precursors could be partly retained on alumina support after impregnation and drying, although the interface reaction between different metal precursors and alumina support unavoidably took place. Then the catalysts were sulfided and characterized by N2 physisorption, TEM and XPS analyses. The results showed that different metal precursors in impregnating solution could mainly result in the difference in both the morphology of(Ni)Mo S2 slabs and the promoting effect of Ni species. The catalyst prepared mainly with [P2Mo5O23]^(6-)-like species used as precursors exhibited worse dispersion of(Ni)Mo S2 slabs and lower ratio of Ni–Mo–S active phases than the one with [Mo4(citrate)2O11]^(4-)-like species. Promisingly, the catalyst prepared with co-existing [Mo4(citrate)2O11]^(4-)-like, [P2Mo18O62]^(6-)-like and [P2Mo5O23]^(6-)-like species showed better hydrodesulfurization activity for 4,6-DMDBT thanks to its more well-dispersed Ni–Mo–S active phases.
文摘The acid gas absorption in four potassium based amino acid salt solutions was predicted using artificial neural network(ANN). Two hundred fifty-five experimental data points for CO_2 absorption in the four potassium based amino acid salt solutions containing potassium lysinate, potassium prolinate, potassium glycinate, and potassium taurate were used in this modeling. Amine salt solution's type, temperature, equilibrium partial pressure of acid gas, the molar concentration of the solution, molecular weight, and the boiling point were considered as inputs to ANN to prognosticate the capacity of amino acid salt solution to absorb acid gas. Regression analysis was employed to assess the performance of the network. Levenberg–Marquardt back-propagation algorithm was used to train the optimal ANN with 5:12:1 architecture. The model findings indicated that the proposed ANN has the capability to predict precisely the absorption of acid gases in various amino acid salt solutions with Mean Square Error(MSE) value of 0.0011, the Average Absolute Relative Deviation(AARD) percent of 5.54%,and the correlation coefficient(R^2) of 0.9828.
基金financially supported by the National Natural Science Foundation of China(No.51371039)the Priority Academic Program Development of Jiangsu Higher Education Institutions(PAPD),Jiangsu Province,China
文摘Potentiodynamic polarization tests and slow strain rate test（SSRT） in combination with fracture morphology observations were conducted to investigate the stress corrosion cracking（SCC） behavior of 7003 aluminum alloy（AA7003） in acid and alkaline chloride solutions under various applied potentials（Ea）. The results show that AA7003 is to a certain extent susceptible to SCC via anodic dissolution（AD） at open-circuit potential（OCP） and is highly susceptible to hydrogen embrittlement（HE） at high negative Ea in the solutions with p H levels of 4 and 11. The susceptibility increases with negative shift in the potential when Ea is less than-1000 m V vs. SCE. However, the susceptibility distinctly decreases because of the inhibition of AD when Ea is equal to-1000 m V vs. SCE. In addition, the SCC susceptibility of AA7003 in the acid chloride solution is higher than that in the alkaline solution at each potential. Moreover, the effect of hydrogen on SCC increases with increasing hydrogen ion concentration.
基金This research was supported by the National Science and Technology Special Foundation for Major Large Oil and Gas Fields and Coal Bed Methane Development(2011ZX05042-003)the Provincial Ministry of State Key Laboratory Breeding Base of Open Projects Henan Gas Geology and Gas Control Laboratory(WS2013B06).
文摘The reaction between carbonic acid and montmorillonite minerals was studied in order to provide a theoretical basis for analyzing changes in the physical properties of coal seams after CO_(2)injection and for optimizing CO_(2) pumping parameters.A single montmorillonite mineral of purity[90%was selected and subjected to reactions at 25,35,and 45℃in carbonic acid solutions of varying acidity.The Si and Al concentrations in the solutions and the structure and elemental compositions of the montmorillonite before and after the reactions were analyzed using a spectrophotometer,an X-ray diffractometer,and an energy-dispersive X-ray spectrometer;kinetic reaction models were established for the dissolution of Si and Al in carbonic acid solutions in order to estimate the apparent activation energy of Si dissolution under different acidity conditions.The results indicate that Al dissolved rapidly and soon reached solubility equilibrium.On the other hand,Si concentration in the solutions increased rapidly and then gradually declined with vibrations,with maximum values at 25,35,and 45℃,which were observed at approximately 96,72,and 48 h,respectively.In addition,Si dissolution fitted the diffusion-controlled reaction model well;as the pH value decreased,the apparent activation energy of Si dissolution decreased,and Si became easier to dissolve.Furthermore,it was concluded that as a weak acid,carbonic acid causes little damage to the mineral structure of montmorillonite.
基金supported by the National Natural Science Foundation of China(No.51104186)
文摘The existing form of molybdenum in acidic sulfate solution was studied by means of ion exchange, infrared （IR） spectra and X-ray photoelectron spectroscopy （XPS）. The results indicate that the anionic molybdenum species are predominant in acidic sulfate solution, and Mo（VI） can combine with sulfate radical to form heteropoly acid anions [Mo205（804）2]2- and [MoO2（HSO4）4]2-. With the decrease in solution pH from 1.92 to 0.06, the existing form of Mo（VI） changes from MovO21（OH）3^3- to [Mo205（S04）2]2- and then becomes [MoOz（HSO4）4]2-, which results in the decrease in the resin adsorption capacity for molybdenum.
基金supported by the National Natural Science Foundation of China(No.51201172)
文摘The corrosion-wear behavior of a nanocrystalline Fe_（88）Si_（12） alloy disc coupled with a Si_3N_4 ball was investigated in acid（pH 3） and alkaline（pH 9） aqueous solutions. The dry wear was also measured for reference. The average friction coefficient of Fe_（88）Si_（12） alloy in the pH 9 solution was approximately 0.2, which was lower than those observed for Fe_（88）Si_（12） alloy in the pH 3 solution and in the case of dry wear. The fluctuation of the friction coefficient of samples subjected to the pH 9 solution also showed similar characteristics. The wear rate in the pH 9 solution slightly increased with increasing applied load. The wear rate was approximately one order of magnitude less than that in the pH 3 solution and was far lower than that in the case of dry wear, especially at high applied load. The wear traces of Fe_（88）Si_（12） alloy under different wear conditions were examined and analyzed by scanning electron microscopy, energy-dispersive X-ray spectroscopy, and X-ray photoelectron spectroscopy. The results indicated that the tribo-chemical reactions that involve oxidation of the worn surface and hydrolysis of the Si_3N_4 ball in the acid solution were restricted in the pH 9 aqueous solution. Thus, water lubrication can effectively improve the wear resistance of nanocrystalline Fe_（88）Si_（12） alloy in the pH 9 aqueous solution.
文摘The electrochemical-voltammetry behavior of vanillin, heliotropin, anisaldehyde on the surface of Pt, Au electrodes in acid solution has been studied by means of the electrochemical cyclic voltammetry method. It was found that the electrochemical processes of them are irreversible on both Pt and Au electrodes. The electrochemical activity of vanillin is stronger than heliotropin's and heliotropin's is stronger than anisaldehyde's on Pt electrode. While the electrochemical activity of anisaldehyde is stronger than heliotropin's and vanillin's is the weakest on Au. The results indicate that when they are used as additives for electroplating, they must be consumptive, and it will improve the leveling ability of plating solution and brightness of the deposition layer.
基金the Brain Pool Programthrough the National Research Foundation of Korea (NRF)funded by the Ministry of Science and ICT (Grant No.2019H1D3A2A02101993).The author Sadia Ilyas is gratefulto NRF for presenting the Brain Pool Scientists award.
文摘This study addresses the liquid-liquid extraction behavior of phosphorus from a sulfuric acid solution using benzyl dimethyl amine(BDMA)in kerosene.The extraction equilibria investigated with varied BDMA concentrations could reveal the formation of 3[BDMA]·[H_(3)PO_(4)]^(-)complex in the organic phase.The thermodynamic properties determined at various temperatures indicated that the process was exothermic with a calculated enthalpy(△H^(Θ))of−24.0 kJ·mol^(−1).The organic-to-aqueous phase(O/A)volume ratio was varied to elucidate the quantitative extraction of phosphorus.The McCabe-Thiele diagram plotted for the extraction isotherm was validated for the requirement of three counter-current stages in the extraction at an O/A volume ratio of 2.0/3.5.The back-extraction of phosphorus from the loaded organic phase was quantitatively achieved by contacting 4.0 mol·L−1 H2SO4 solution in three stages of counter-current contact at an O/A volume ratio of 3/2.This study can be applied to remove phosphorus from the sulfuric acid leach solutions of monazite processing,and many other solutions.
