Effects of various sintering methods such as spark plasma sintering(SPS), hot pressing(HP) and electric resistance sintering(ERS) on the microstructure and mechanical properties of commercial pure titanium(CP-Ti) powd...Effects of various sintering methods such as spark plasma sintering(SPS), hot pressing(HP) and electric resistance sintering(ERS) on the microstructure and mechanical properties of commercial pure titanium(CP-Ti) powder consolidations with particle size of <147 μm, <74 μm and <43 μm were studied. The smaller particle powders are densified to proceed at a higher rate. Dense titanium with relative density up to 99% is found to take place at 850 °C under 30 MPa of SPS and HP condition. However, in case of ERS, CP-Ti powders were densified almost at 950 °C under 30 MPa. The microstructure of sintered titanium is composed of equiaxed grains at 850-950 °C. The yield strength of sintered body composed of <43 μm powder is 858 MPa by using SPS at 850 °C under 30 MPa. When there is a higher content of small particle, the higher yield strength value is obtained both by using SPS and HP. However, when ERS is introduced, the highest yield strength is 441 MPa at 950 °C under 30 MPa, which shows much lower values than those by SPS and HP methods. ERS method takes much less sintering time compared with SPS and HP. Nevertheless, higher sintering temperature results in lower strength and elongation because of brittle fracture.展开更多
Aiming at the comprehensive utilization of the rare-earth resources and the preparation of the high-performance low-cost Nd-Fe-B magnets,sintered magnets with different Ce substitution amounts of 17.2 wt%,24.8 wt%and ...Aiming at the comprehensive utilization of the rare-earth resources and the preparation of the high-performance low-cost Nd-Fe-B magnets,sintered magnets with different Ce substitution amounts of 17.2 wt%,24.8 wt%and 31.8 wt%were prepared by intergranularalloy method.The influence of substitution of Ce for Nd on their microstructure and magnetic properties in this work was detailedly investigated.The results indicated that the remanence(Br)and the maximum energy product((BH)max)of the sintered magnets decreased monotonic ally with the increase in Ce substitution.However,the obvious enhancement of coercivity(Hcj)was also observed,which was mainly due to the improvement of microstructure and the smooth,continuous grain boundary(GB).It can be found that a reasonable Ce substitution of 24.8 wt%for the sintered magnets could promote the refinement of microstructure,leading to the realization of superior magnetic properties.It is expected that the investigations could be beneficial to offer a feasible method for preparing the high-performance low-cost Ce-doped magnets.展开更多
A three-dimensional finite element thermal model in direct metal laser sintering(DMLS) including the effect of powder-to-solid transition were established to predict sintering zone, which benefited the determination o...A three-dimensional finite element thermal model in direct metal laser sintering(DMLS) including the effect of powder-to-solid transition were established to predict sintering zone, which benefited the determination of suitable process parameters in DMLS. The nonlinear transient model of the metals thermal conductivity for powder-to-solid transition was developed. The model uses solid thermal properties of material in liquid-phase zone, transitional ones in sintering or sintered zone and powder ones in unsintered zones of powder bed to predict, respectively. Sintering zone boundary was estimated by maximum temperature history profile. Experiments were carried out using multi-component Cu-based metal powder. Compared experimental and predicted results, the mean error of sintering depth and width are 7.8% and 14.4%, respectively, which confirms the accuracy of the FEM prediction.展开更多
Different material properties leads to different metal fracture behaviors. Even if the powder material is composed of plastic metal, the fracture still does not show macroscopic plastic deformation characteristics if ...Different material properties leads to different metal fracture behaviors. Even if the powder material is composed of plastic metal, the fracture still does not show macroscopic plastic deformation characteristics if the material contains a large number of voids. Eight node isoparametric elastic plastic finite element method was used to simulate the tensile process of sintered powder material. By setting a number of voids in the analyzed metal cuboid, the initial density was taken into consideration. The material properties of the three dimensional solid for the tensile simulation were defined with reference to the known pure iron material parameters. The load displacement curves during elongation were obtained with a universal testing machine, and then the simulated curves were compared with the experimental results. The factors that cause the stress concentration and strength decrease were analyzed according to the simulated equivalent von Mises stress distribution.展开更多
Slip line method for sintered powder materials under condition of axial symmetry is proposed based on the simplified yield condition of sintered powder materials and Haar-von Karman perfect plastic criterion. The equa...Slip line method for sintered powder materials under condition of axial symmetry is proposed based on the simplified yield condition of sintered powder materials and Haar-von Karman perfect plastic criterion. The equations of slip line and stress along slip line are derived, and numerical solutions are given. Deformation load in closed die upsetting of sintered copper cylinder is calculated by slip line method, and theoretical solutions are compared with experimental results.展开更多
Gadolinium zirconate（Gd2Zr2O7） nanocrystals were prepared via two different combustion methods： citric acid combustion（CAC） and stearic acid combustion（SAC）. The effects of the different preparation methods on ...Gadolinium zirconate（Gd2Zr2O7） nanocrystals were prepared via two different combustion methods： citric acid combustion（CAC） and stearic acid combustion（SAC）. The effects of the different preparation methods on the phase composition, microtopography, and sintering densification of the resulting Gd2Zr2O7 nanopowders were investigated by thermal-gravimetric and differential thermal analysis（TG-DTA）, Fourier transform infrared spectroscopy（FTIR）, X-ray diffraction（XRD）, and transmission electron microscopy（TEM） techniques. The results indicated that both methods could produce Gd2Zr2O7 nanopowders with an excellent defective fluorite structure. The reaction time was reduced by the SAC method, compared with the CAC method. The nanopowders synthesized by the two methods were different in grain size distribution. The resulting nanoparticle diameter was about 50 nm for CAC and 10 nm for SAC. After vacuum sintering, the sintered bodies also had a different relative density of about 93% and 98%, respectively. Thus the preparation of Gd2Zr2O7 nanopowders by SAC was the first choice to achieve the desired sintering densification.展开更多
基金Project(K0004130) supported by the Fundamental R&D Program for Core Technology of Materials funded by the Ministry of Knowledge Economy,Korea
文摘Effects of various sintering methods such as spark plasma sintering(SPS), hot pressing(HP) and electric resistance sintering(ERS) on the microstructure and mechanical properties of commercial pure titanium(CP-Ti) powder consolidations with particle size of <147 μm, <74 μm and <43 μm were studied. The smaller particle powders are densified to proceed at a higher rate. Dense titanium with relative density up to 99% is found to take place at 850 °C under 30 MPa of SPS and HP condition. However, in case of ERS, CP-Ti powders were densified almost at 950 °C under 30 MPa. The microstructure of sintered titanium is composed of equiaxed grains at 850-950 °C. The yield strength of sintered body composed of <43 μm powder is 858 MPa by using SPS at 850 °C under 30 MPa. When there is a higher content of small particle, the higher yield strength value is obtained both by using SPS and HP. However, when ERS is introduced, the highest yield strength is 441 MPa at 950 °C under 30 MPa, which shows much lower values than those by SPS and HP methods. ERS method takes much less sintering time compared with SPS and HP. Nevertheless, higher sintering temperature results in lower strength and elongation because of brittle fracture.
基金financially supported by the Sichuan Province Science and Technology Support Program(No.2014GZ0090)the Key Technology and Development Program of PanXi Experimental Area(No.2016KJT0018).
文摘Aiming at the comprehensive utilization of the rare-earth resources and the preparation of the high-performance low-cost Nd-Fe-B magnets,sintered magnets with different Ce substitution amounts of 17.2 wt%,24.8 wt%and 31.8 wt%were prepared by intergranularalloy method.The influence of substitution of Ce for Nd on their microstructure and magnetic properties in this work was detailedly investigated.The results indicated that the remanence(Br)and the maximum energy product((BH)max)of the sintered magnets decreased monotonic ally with the increase in Ce substitution.However,the obvious enhancement of coercivity(Hcj)was also observed,which was mainly due to the improvement of microstructure and the smooth,continuous grain boundary(GB).It can be found that a reasonable Ce substitution of 24.8 wt%for the sintered magnets could promote the refinement of microstructure,leading to the realization of superior magnetic properties.It is expected that the investigations could be beneficial to offer a feasible method for preparing the high-performance low-cost Ce-doped magnets.
文摘A three-dimensional finite element thermal model in direct metal laser sintering(DMLS) including the effect of powder-to-solid transition were established to predict sintering zone, which benefited the determination of suitable process parameters in DMLS. The nonlinear transient model of the metals thermal conductivity for powder-to-solid transition was developed. The model uses solid thermal properties of material in liquid-phase zone, transitional ones in sintering or sintered zone and powder ones in unsintered zones of powder bed to predict, respectively. Sintering zone boundary was estimated by maximum temperature history profile. Experiments were carried out using multi-component Cu-based metal powder. Compared experimental and predicted results, the mean error of sintering depth and width are 7.8% and 14.4%, respectively, which confirms the accuracy of the FEM prediction.
文摘Different material properties leads to different metal fracture behaviors. Even if the powder material is composed of plastic metal, the fracture still does not show macroscopic plastic deformation characteristics if the material contains a large number of voids. Eight node isoparametric elastic plastic finite element method was used to simulate the tensile process of sintered powder material. By setting a number of voids in the analyzed metal cuboid, the initial density was taken into consideration. The material properties of the three dimensional solid for the tensile simulation were defined with reference to the known pure iron material parameters. The load displacement curves during elongation were obtained with a universal testing machine, and then the simulated curves were compared with the experimental results. The factors that cause the stress concentration and strength decrease were analyzed according to the simulated equivalent von Mises stress distribution.
文摘Slip line method for sintered powder materials under condition of axial symmetry is proposed based on the simplified yield condition of sintered powder materials and Haar-von Karman perfect plastic criterion. The equations of slip line and stress along slip line are derived, and numerical solutions are given. Deformation load in closed die upsetting of sintered copper cylinder is calculated by slip line method, and theoretical solutions are compared with experimental results.
文摘Gadolinium zirconate（Gd2Zr2O7） nanocrystals were prepared via two different combustion methods： citric acid combustion（CAC） and stearic acid combustion（SAC）. The effects of the different preparation methods on the phase composition, microtopography, and sintering densification of the resulting Gd2Zr2O7 nanopowders were investigated by thermal-gravimetric and differential thermal analysis（TG-DTA）, Fourier transform infrared spectroscopy（FTIR）, X-ray diffraction（XRD）, and transmission electron microscopy（TEM） techniques. The results indicated that both methods could produce Gd2Zr2O7 nanopowders with an excellent defective fluorite structure. The reaction time was reduced by the SAC method, compared with the CAC method. The nanopowders synthesized by the two methods were different in grain size distribution. The resulting nanoparticle diameter was about 50 nm for CAC and 10 nm for SAC. After vacuum sintering, the sintered bodies also had a different relative density of about 93% and 98%, respectively. Thus the preparation of Gd2Zr2O7 nanopowders by SAC was the first choice to achieve the desired sintering densification.
