This study investigated enhancing the wear resistance of Ti6Al4V alloys for medical applications by incorporating Ti C nanoreinforcements using advanced spark plasma sintering(SPS). The addition of up to 2.5wt% Ti C s...This study investigated enhancing the wear resistance of Ti6Al4V alloys for medical applications by incorporating Ti C nanoreinforcements using advanced spark plasma sintering(SPS). The addition of up to 2.5wt% Ti C significantly improved the mechanical properties, including a notable 18.2% increase in hardness(HV 332). Fretting wear tests against 316L stainless steel(SS316L) balls demonstrated a 20wt%–22wt% reduction in wear volume in the Ti6Al4V/Ti C composites compared with the monolithic alloy. Microstructural analysis revealed that Ti C reinforcement controlled the grain orientation and reduced the β-phase content, which contributed to enhanced mechanical properties. The monolithic alloy exhibited a Widmanstätten lamellar microstructure, while increasing the Ti C content modified the wear mechanisms from ploughing and adhesion(0–0.5wt%) to pitting and abrasion(1wt%–2.5wt%). At higher reinforcement levels, the formation of a robust oxide layer through tribo-oxide treatment effectively reduced the wear volume by minimizing the abrasive effects and plastic deformation. This study highlights the potential of SPS-mediated Ti C reinforcement as a transformative approach for improving the performance of Ti6Al4V alloys, paving the way for advanced medical applications.展开更多
Sintering is a critical process in steel production that facilitates the efficient utilization of iron ore resources.However,compared to advanced sintering technologies,China’s sintering methods still exhibit high en...Sintering is a critical process in steel production that facilitates the efficient utilization of iron ore resources.However,compared to advanced sintering technologies,China’s sintering methods still exhibit high energy consumption,with typical solid fuel consumption for sintering of about 55 kg/t.In response,a pellet sintering process has been developed and its behavior has been investigated at sintering bed heights of 750 and 1500 mm.Additionally,a technical and economic comparison with traditional sintering methods has been conducted.The results indicate that at a bed height of 750 mm,the pellet sintering method can significantly reduce solid fuel consumption by approximately 30.82%,dropping from 70.75 to 48.95 kg/t.Additionally,the coke rate decreased from 4.55%to 3.20%,and harmful emissions in the flue gas were also reduced.As the bed height increases to 1500 mm,sintering performance improves even further.The coke rate is reduced to 3.00%,and solid fuel consumption decreases to 41.27 kg/t,approaching the world’s advanced level(≤40 kg/t).Technical and economic analysis also indicates that adopting the pellet sintering process can lower sintering costs by about 2.18 dollars/t.展开更多
During the sintering process of iron ore,a large amount of nitrogen oxides is generated,for which there is currently no efficient and economical treatment process.Therefore,it is necessary to implement process control...During the sintering process of iron ore,a large amount of nitrogen oxides is generated,for which there is currently no efficient and economical treatment process.Therefore,it is necessary to implement process control in sintering production to keep the mass concentration of NO_(x)in sintering flue gas at a low level.Through industrial trials at sintering sites,methods such as correlation analysis,path analysis,and multiple linear regression were applied to analyze the influence of various factors on NO emissions during the sintering process.The results indicate that negative correlations exist between nitrogen monoxide(NO)emissions and negative pressure,permeability index,O_(2) concentration,CO concentration,and flue gas temperature.Conversely,positive correlations exist between NO emissions and dust concentration,water vapor volume fraction,and sintering bed speed.Among these factors,O_(2) concentration and dust concentration are identified as the most significant influencing factors on NO emissions.By analyzing the masses and modes of influence of different factors,the mechanisms of action of each factor were obtained.Specifically,O_(2) concentration,dust concentration,permeability index,CO concentration,and flue gas temperature play a direct dominant role in NO emissions during the sintering process,while water vapor volume fraction,sintering trolley speed,and negative pressure have an indirect effect.A predictive model for NO mass concentration in flue gas was established with an accuracy rate of 91.6%,showing consistent overall trends with actual values.Finally,denitrification strategies for sintering industrial production were proposed,along with prospects for preliminary denitrification of sintering flue gas using fluidized bed conditions in the duct.展开更多
The mineral composition of the sinter affects the quality of cold-bonded briquettes(CBB),which are prepared from returned sinter fines and serve as a cleaner blast furnace charge.Pulverization rate,compressive strengt...The mineral composition of the sinter affects the quality of cold-bonded briquettes(CBB),which are prepared from returned sinter fines and serve as a cleaner blast furnace charge.Pulverization rate,compressive strength,reduction disintegration index(RDI)and compressive strength after reduction experiment were tested to analyze the experimental parameters of CBB under the influence of different basicities and sintering time.The results show that when the basicity of CBB is increased from 0.5 to 1.5,the pulverization rate increases,and performance indexes such as compressive strength,RDI,and compressive strength exhibit a decreasing trend.When the basicity is increased from 1.5 to 3.0,all the aforementioned performance indexes are improved.When the sintering time is extended from 0 to 8 h,the properties mentioned above are improved.The results of X-ray diffraction,microstructure,and thermodynamic calculations confirm that the hematite in the mineral composition of CBB tends to convert into calcium ferrite,which leads to the increased compressive strength of CBB.The reasonable basicity and sintering time during sinter preparation not only form the desired mineral composition but also improve the properties of the CBB.展开更多
Limestone was pretreated via the mechanical activation method,and burnt lime was partially substituted by the pretreated limestone for better sinter indices and lower sintering costs.With the reduction in the size dis...Limestone was pretreated via the mechanical activation method,and burnt lime was partially substituted by the pretreated limestone for better sinter indices and lower sintering costs.With the reduction in the size distribution of the pretreated limestone,the particle morphology,the activity of the calcined limestone and the fluidity of the liquid phase during sintering are all improved.When the substitution ratio of the pretreated limestone for burnt lime is kept at 50%,the granulation performance and sinter indices in sinter pot tests are both better compared with that of the base case.Much denser interleaved texture in product sinter is formed with the reduction of sinter porosity and improvement of silico-ferrite of calcium and alumina amount.When the particle size of the pretreated limestone is maintained within the optimal range of 0–2 mm,the tumble index,yield and productivity increase by 7.2%,2.6%and 11.2%,respectively,while the solid fuel rate decreases by 8.7%.In the corresponding sinter industry production,the tumble index and output of the product sinter are comparable to those of the base case,while the coke dosage is reduced by 9.0%.Reduction index and reduction degradation index(RDI_(+3.15))are both higher than 74%.The cost of raw materials in sintering process can be greatly reduced.展开更多
A pre-reduction sintering process with flue gas recirculation(PSP_(fsg)-FGR)was developed to mitigate alkalis harm to the blast furnace and reduce the flue gas emission in the whole ironmaking process.The results indi...A pre-reduction sintering process with flue gas recirculation(PSP_(fsg)-FGR)was developed to mitigate alkalis harm to the blast furnace and reduce the flue gas emission in the whole ironmaking process.The results indicated that the pre-reduction sintering process(PSP)can effectively remove 58.02%of K and 30.68%of Na from raw mixtures and improve yield and tumbler index to 74.40%and 68.69%,respectively.Moreover,PSP was conducive to reducing NO_(x) and SO_(2)emissions and simultaneously increasing CO content in flue gas.Circulating CO-containing flue gas to sintering bed effectively recycled CO and further improved K and Na removal ratio to 74.11%and 32.92%,respectively.Microstructural analysis revealed that the pre-reduced sinter mainly consisted of magnetite,wustite and a small quantity of metallic iron,and very few silicate glass phase was also formed.This process can simultaneously realize alkali metal elements removal as well as flue gas emission reduction from the integrated ironmaking process.展开更多
Volatile organic compounds(VOCs)present significant risks to both human health and the environment.As a result,there has been increasing research on their formation processes,emission patterns,and emission reduction t...Volatile organic compounds(VOCs)present significant risks to both human health and the environment.As a result,there has been increasing research on their formation processes,emission patterns,and emission reduction technologies.Sintered ore,a key raw material in ironmaking,requires substantial amounts of fossil fuels such as coal and coke in its production,leading to significant VOC emissions.However,research on VOC emission patterns during the sintering process remains limited.Thus,the influence of factors such as moisture content in the sintering mixture,fuel type,fuel ratio,and coal-to-coke ratio on VOC emissions was investigated through sintering cup experiments.Additionally,the reaction pathways of hydrocarbons within the sintering bed were analyzed using temperature distribution and thermodynamic calculations.In the sintering process using coke powder,the emissions of total volatile organic compounds and non-methane hydrocarbons per ton of sintered ore are 18.78 and 11.14 g,respectively,whereas emissions from coal are substantially higher at 378.27 and 32.55 g.VOC emissions exhibit a linear correlation with the total volatile matter input during sintering,with most VOCs originating from volatile matter.The improved heat transfer conditions reduce the preheating zone thickness,allowing more VOCs to remain in the high-temperature region.展开更多
Steel rolling sludge,an oil-containing waste generated during steel production,was difficult to manage.Prolonged storage poses significant environmental and health hazards.Most steel enterprises in China use steel rol...Steel rolling sludge,an oil-containing waste generated during steel production,was difficult to manage.Prolonged storage poses significant environmental and health hazards.Most steel enterprises in China use steel rolling sludge directly as a raw material for sintering.However,its adhesive nature caused poor mixing with other materials,affecting the quality of the sinter.Herein,the incorporation of steel rolling sludge incineration slag into the sintering process was investigated for experimental purposes.The results indicated that adding 1%incinerated steel rolling sludge to the sintering raw material was feasible.At this proportion,both the yield and the tumbler index of the sinter have improved,primarily due to the oxidation reaction of Fe_(3)O_(4)present in the steel rolling sludge incineration slag during the sintering process,which significantly increases the sensible heat of the sinter and enhances the sintering mineralization reaction.Notably,the addition of steel rolling sludge incineration slag reduced dioxin concentrations in the sintering flue gas.Although CO,NO_(x),and SO_(2)emission concentrations slightly increased,the existing flue gas treatment system effectively controlled their emissions.展开更多
Sinter is the core raw material for blast furnaces.Flue pressure,which is an important state parameter,affects sinter quality.In this paper,flue pressure prediction and optimization were studied based on the shapley a...Sinter is the core raw material for blast furnaces.Flue pressure,which is an important state parameter,affects sinter quality.In this paper,flue pressure prediction and optimization were studied based on the shapley additive explanation(SHAP)to predict the flue pressure and take targeted adjustment measures.First,the sintering process data were collected and processed.A flue pressure prediction model was then constructed after comparing different feature selection methods and model algorithms using SHAP+extremely random-ized trees(ET).The prediction accuracy of the model within the error range of±0.25 kPa was 92.63%.SHAP analysis was employed to improve the interpretability of the prediction model.The effects of various sintering operation parameters on flue pressure,the relation-ship between the numerical range of key operation parameters and flue pressure,the effect of operation parameter combinations on flue pressure,and the prediction process of the flue pressure prediction model on a single sample were analyzed.A flue pressure optimization module was also constructed and analyzed when the prediction satisfied the judgment conditions.The operating parameter combination was then pushed.The flue pressure was increased by 5.87%during the verification process,achieving a good optimization effect.展开更多
Poor permeability and low sintering productivity restrict the development of high-bed sintering.An efficient method of the double-layer sintering process(DLSP)was proposed to achieve high-bed sintering and solve the a...Poor permeability and low sintering productivity restrict the development of high-bed sintering.An efficient method of the double-layer sintering process(DLSP)was proposed to achieve high-bed sintering and solve the aforementioned problems.Theoretical calculation and sintering pot experiments were implemented to investigate the double-layer sintering process.Traditional sintering process and DLSP were compared in terms of sintering indices,metallurgical properties and morphology characterization.Under the condition of traditional sintering process,DLSP successfully realized fast velocity and highly productive sintering of 1000-mm high bed.After the sintering bed is charged and ignited twice,the air permeability of the bed has been greatly improved.Sintering time is shortened significantly by simultaneous sintering of the upper and lower feed layers.Under the condition of bed height proportion of 350/650 mm and pre-sintering time of 20 min,the yield,tumbler strength,productivity and solid fuel consumption are 69.96%,65.87%,1.71 t(m^(2)h)^(-1)and 56.71 kg/t,respectively.Magnetite,hematite,calcium ferrite and complex calcium ferrite are the main phases of DLSP products.The metallurgical properties of DSLP products meet the requirement of ironmaking.It indicates that DLSP is an effective method to solve the disadvantages of bad permeability and low sintering productivity in high-bed sintering.展开更多
As the bed depth increases,sintering yield increases,but the productivity decreases.To reveal the reasons for the decrease in productivity and explore targeted solutions,the bed resistance of mixtures,wet zone,and com...As the bed depth increases,sintering yield increases,but the productivity decreases.To reveal the reasons for the decrease in productivity and explore targeted solutions,the bed resistance of mixtures,wet zone,and combustion zone was analyzed in the laboratory.The results showed that the decreased porosity of mixture resulted in the increased bed resistance by 160.56%when the bed depth increased from 600 to 1000 mm.After improving porosity of 1%by adding loosening bars with optimized size and distribution,the bed resistance decreased,and the productivity increased by 5%.The increase in bed depth increased the thickness of the wet zone from 120 to 680 mm and the resistance from 1.56 to 8.83 kPa.By using a three-stage intensive mixer and pre-adding water for granulation,the moisture of mixture was reduced by 0.6%,and the sintering productivity increased by 4%.Besides,the high bed resistance is mainly caused by the increase in the thickness of the combustion zone from 31.9 to 132.7 mm,and the bed resistance increased from 0.70 to 5.62 kPa.The bed resistance of the combustion zone at 900 mm was increased by 90.51%compared to 700 mm.After optimization of the distribution of coke breeze,the thickness of combustion zone at the lower layer decreased from 132.7 to 106.84 mm and permeability improved significantly.展开更多
A key component of future lunar missions is the concept of in-situ resource utilization(ISRU),which involves the use of local resources to support human missions and reduce dependence on Earth-based supplies.This pape...A key component of future lunar missions is the concept of in-situ resource utilization(ISRU),which involves the use of local resources to support human missions and reduce dependence on Earth-based supplies.This paper investigates the thermal processing capability of lunar regolith without the addition of binders,with a focus on large-scale applications for the construction of lunar habitats and infrastructure.The study used a simulant of lunar regolith found on the Schr?dinger Basin in the South Pole region.This regolith simulant consists of20 wt%basalt and 80 wt%anorthosite.Experiments were conducted using a high power CO_(2)laser to sinter and melt the regolith in a 80 mm diameter laser spot to evaluate the effectiveness of direct large area thermal processing.Results indicated that sintering begins at approximately 1180℃and reaches full melt at temperatures above 1360℃.Sintering experiments with this material revealed the formation of dense samples up to 11 mm thick,while melting experiments successfully produced larger samples by overlapping molten layers and additive manufacturing up to 50 mm thick.The energy efficiency of the sintering and melting processes was compared.The melting process was about 10 times more energy efficient than sintering in terms of material consolidation,demonstrating the promising potential of laser melting technologies of anorthosite-rich regolith for the production of structural elements.展开更多
Real-time prediction and precise control of sinter quality are pivotal for energy saving,cost reduction,quality improvement and efficiency enhancement in the ironmaking process.To advance,the accuracy and comprehensiv...Real-time prediction and precise control of sinter quality are pivotal for energy saving,cost reduction,quality improvement and efficiency enhancement in the ironmaking process.To advance,the accuracy and comprehensiveness of sinter quality prediction,an intelligent flare monitoring system for sintering machine tails that combines hybrid neural networks integrating convolutional neural network with long short-term memory(CNN-LSTM)networks was proposed.The system utilized a high-temperature thermal imager for image acquisition at the sintering machine tail and employed a zone-triggered method to accurately capture dynamic feature images under challenging conditions of high-temperature,high dust,and occlusion.The feature images were then segmented through a triple-iteration multi-thresholding approach based on the maximum between-class variance method to minimize detail loss during the segmentation process.Leveraging the advantages of CNN and LSTM networks in capturing temporal and spatial information,a comprehensive model for sinter quality prediction was constructed,with inputs including the proportion of combustion layer,porosity rate,temperature distribution,and image features obtained from the convolutional neural network,and outputs comprising quality indicators such as underburning index,uniformity index,and FeO content of the sinter.The accuracy is notably increased,achieving a 95.8%hit rate within an error margin of±1.0.After the system is applied,the average qualified rate of FeO content increases from 87.24%to 89.99%,representing an improvement of 2.75%.The average monthly solid fuel consumption is reduced from 49.75 to 46.44 kg/t,leading to a 6.65%reduction and underscoring significant energy saving and cost reduction effects.展开更多
1.Introduction.Ni-Mn-X(X=Ga,In,Sn,or Sb)Heusler alloys have versatile properties[1-4],such as shape memory effect[1],superelastic-ity[5],magnetocaloric effect[3],elastocaloric effect[6],and even multicaloric effect[7]...1.Introduction.Ni-Mn-X(X=Ga,In,Sn,or Sb)Heusler alloys have versatile properties[1-4],such as shape memory effect[1],superelastic-ity[5],magnetocaloric effect[3],elastocaloric effect[6],and even multicaloric effect[7],that indicate their potential for use in actu-ators,sensors,micropumps,energy harvesters,and solid-state re-frigeration[8-10].Among the alloys,Ni-Mn-Sn-based alloys are environment-friendly and cost-effective[6,7,11],and hence,they have received widespread attention.展开更多
High-performance graphite materials have important roles in aerospace and nuclear reactor technologies because of their outstanding chemical stability and high-temperature performance.Their traditional production meth...High-performance graphite materials have important roles in aerospace and nuclear reactor technologies because of their outstanding chemical stability and high-temperature performance.Their traditional production method relies on repeated impregnation-carbonization and graphitization,and is plagued by lengthy preparation cycles and high energy consumption.Phase transition-assisted self-pressurized selfsintering technology can rapidly produce high-strength graphite materials,but the fracture strain of the graphite materials produced is poor.To solve this problem,this study used a two-step sintering method to uniformly introduce micro-nano pores into natural graphite-based bulk graphite,achieving improved fracture strain of the samples without reducing their density and mechanical properties.Using natural graphite powder,micron-diamond,and nano-diamond as raw materials,and by precisely controlling the staged pressure release process,the degree of diamond phase transition expansion was effectively regulated.The strain-to-failure of the graphite samples reached 1.2%,a 35%increase compared to samples produced by fullpressure sintering.Meanwhile,their flexural strength exceeded 110 MPa,and their density was over 1.9 g/cm^(3).The process therefore produced both a high strength and a high fracture strain.The interface evolution and toughening mechanism during the two-step sintering process were investigated.It is believed that the micro-nano pores formed have two roles:as stress concentrators they induce yielding by shear and as multi-crack propagation paths they significantly lengthen the crack propagation path.The two-step sintering phase transition strategy introduces pores and provides a new approach for increasing the fracture strain of brittle materials.展开更多
Ceramic dielectric materials with high dielectric strength and mechanisms of their internal factors affecting dielectric strength are significantly valuable for industrial application,especially for selection of suita...Ceramic dielectric materials with high dielectric strength and mechanisms of their internal factors affecting dielectric strength are significantly valuable for industrial application,especially for selection of suitable dielectric materials for high-power microwave transmission devices and reliable power transmission.Pure magnesium oxide(MgO),a kind of ceramic dielectric material,possesses great application potential in high-power microwave transmission devices due to its high theoretical dielectric strength,low dielectric constant,and low dielectric loss properties,but its application is limited by high sintering temperature during preparation.This work presented the preparation of a new type of multiphase ceramics based on MgO,which was MgO-1%ZrO_(2)-1%CaCO_(3-x)%MnCO_(3)(MZCM_(x),x=0,0.25,0.50,1.00,1.50,in molar),and their phase structures,morphological features,and dielectric properties were investigated.It was found that inclusion of ZrO_(2) and CaCO_(3) effectively inhibited excessive growth of MgO grains by formation of second phase,while addition of MnCO_(3) promoted the grain boundary diffusion process during the sintering process and reduced activation energy for the grain growth,resulting in a lower ceramic sintering temperature.Excellent performance,including high dielectric strength(Eb=92.3 kV/mm)and quality factor(Q×f=216642 GHz),simultaneously accompanying low dielectric loss(<0.03%),low temperature coefficient of dielectric constant(20.3×10^(–6)℃^(–1),85℃)and resonance frequency(–12.54×10^(–6)℃^(–1)),was achieved in MZCM1.00 ceramics under a relatively low sintering temperature of 1350℃.This work offers an effective solution for selecting dielectric materials for high-power microwave transmission devices.展开更多
Three types of NdFeB magnets with the same composition and different grain sizes were prepared,and then the grain boundary diffusion was conducted using metal Tb under the same technical parameters.The effect of grain...Three types of NdFeB magnets with the same composition and different grain sizes were prepared,and then the grain boundary diffusion was conducted using metal Tb under the same technical parameters.The effect of grain size on the grain boundary diffusion process and properties of sintered NdFeB magnets was investigated.The diffusion process was assessed using X-ray diffractometer,field emission scanning electron microscope,and electron probe microanalyzer.The magnetic properties of the magnet before and after diffusion were investigated.The results show that the grain refinement of the magnet leads to higher Tb utilization efficiency and results in higher coercivity at different temperatures.It can be attributed to the formation of a deeper and more complete core-shell structure,resulting in better magnetic isolation and higher anisotropy of the Nd_(2)Fe_(14)B grains.This work may shed light on developing high coercivity with low heavy rare earth elements through grain refinement.展开更多
ZnAl_(2)O_(4) and ZnAl_(2)O_(4)-based ceramics have attracted much attention from researchers due to their good microwave dielectric,thermal and mechanical properties.In this work,the influence of 5%(in mass)CuO-TiO_(...ZnAl_(2)O_(4) and ZnAl_(2)O_(4)-based ceramics have attracted much attention from researchers due to their good microwave dielectric,thermal and mechanical properties.In this work,the influence of 5%(in mass)CuO-TiO_(2)-Nb_(2)O_(5)(CTN)ternary composite oxide additives with different composition ratios on sintering behavior and properties of ZnAl_(2)O_(4) microwave dielectric ceramics was investigated.When the molar fraction ranges of Cu,Ti and Nb elements in 5%CTN additives are 0.625-0.875,0-0.250 and 0.125-0.625,respectively,sintering temperature of ZnAl_(2)O_(4) ceramics can be reduced from above 1400℃to below 1000℃.The sintering additives CN(Cu:Nb=1:1,molar ratio)and CTN(Cu:Ti:Nb=4:1:3,molar ratio)can reduce sintering temperature of ZnAl_(2)O_(4) ceramics to 975 and 1000℃,respectively,while maintaining good dielectric properties(dielectric constantε_(r)=11.36,quality factor Q׃=8245 GHz andε_(r)=9.52,Q׃=22249 GHz)and flexural strengths(200 and 161 MPa),which are expected to be applied in preparation of low temperature co-fired ceramic(LTCC)materials with copper electrodes.Low-temperature sintering of the ZnAl_(2)O_(4)+CTN system is characterized as activated sintering.Nanometer-level amorphous interfacial films containing Cu,Ti,and Nb elements are observed at the grain boundaries,which may provide fast diffusion pathways for mass transportation during the sintering process.Valence changes of Ti and Cu ions,along with changes of oxygen vacancies,are confirmed,which provides a potential mechanism for reduced sintering temperature of ZnAl_(2)O_(4) ceramics.In addition,a series of reactions occurring at the grain boundaries can activate these boundaries and further promote the sintering densification process.These results suggest a promising way to design a novel LTCC material with excellent properties based on the low temperature sintering of ceramics with the sintering aid of CuO-TiO_(2)-Nb_(2)O_(5) composite oxide.展开更多
A procedure of low temperature solid-phase sintering（LTSS） was carried out to fabricate sintered metal fibrous media（SMFM） with high specific surface area.Stainless steel fibers which were produced by cutting proc...A procedure of low temperature solid-phase sintering（LTSS） was carried out to fabricate sintered metal fibrous media（SMFM） with high specific surface area.Stainless steel fibers which were produced by cutting process were first plated with a coarse copper coating layer by electroless plating process.A low-temperature sintering process was then completed at about 800 °C for 1 h under the protection of hydrogen atmosphere.The results show that a novel SMFM with complex surface morphology and high specific surface area（0.2 m2/g） can be obtained in this way.The effect of sintering temperature on the surface morphology and specific surface area of SMFM was studied by means of scanning electron microscopy and Brunauer-Emmett-Teller.The damage of micro-structure during the sintering process mainly contributed to the loss of specific surface area of SMFM and the optimal sintering temperature was 800 °C.展开更多
The low coercivity is the major factor inhibiting the large-scale commercial utilization of Nd-Ce-Fe-B sintered magnets.In this work,we achieved a record-high coercivity of 15.04 kOe in Ga-doped Nd-Ce-Fe-B sintered ma...The low coercivity is the major factor inhibiting the large-scale commercial utilization of Nd-Ce-Fe-B sintered magnets.In this work,we achieved a record-high coercivity of 15.04 kOe in Ga-doped Nd-Ce-Fe-B sintered magnets with 30 wt%Ce replacing Nd,demonstrating enormous potential.The Ga-doped Nd-Ce-Fe-B magnets with higher boron(HB)and lower boron(LB)content are designed.The coercivity of the HB magnet increases slightly from 10.80 to 12.26 kOe after annealing,attributed to the optimized distribution of grain boundary(GB)phases.In contrast,the coercivity of the LB magnet remarkably increases from 8.13 to 15.04 kOe after annealing.Microstructural observations indicate that the narrow GB phase in the as-sintered magnet is rich in Fe,and the strong exchange coupling of adjacent grains resulted in low coercivity.The evolution of Ga-rich phases reveals a potential formation mechanism of the RE_(6)Fe_(13)Ga phase,that is the RE-Fe amorphous phase and REGa phase in the as-sintered magnet combine to form the RE_(6)Fe_(13)Ga phase and RE-Ga amorphous phase during post-sinter annealing(RE:rare earth).Moreover,the GB phase of the annealed magnet transforms into a Fe-lean phase with a thickness of 16.4 nm.Magnetization and demagnetization behavior characterizations reveal that the exchange decoupling of adjacent grains induced by the optimized GB phases is the main reason for the remarkable coercivity enhancement,which is also validated by micromagnetic simulations.展开更多
文摘This study investigated enhancing the wear resistance of Ti6Al4V alloys for medical applications by incorporating Ti C nanoreinforcements using advanced spark plasma sintering(SPS). The addition of up to 2.5wt% Ti C significantly improved the mechanical properties, including a notable 18.2% increase in hardness(HV 332). Fretting wear tests against 316L stainless steel(SS316L) balls demonstrated a 20wt%–22wt% reduction in wear volume in the Ti6Al4V/Ti C composites compared with the monolithic alloy. Microstructural analysis revealed that Ti C reinforcement controlled the grain orientation and reduced the β-phase content, which contributed to enhanced mechanical properties. The monolithic alloy exhibited a Widmanstätten lamellar microstructure, while increasing the Ti C content modified the wear mechanisms from ploughing and adhesion(0–0.5wt%) to pitting and abrasion(1wt%–2.5wt%). At higher reinforcement levels, the formation of a robust oxide layer through tribo-oxide treatment effectively reduced the wear volume by minimizing the abrasive effects and plastic deformation. This study highlights the potential of SPS-mediated Ti C reinforcement as a transformative approach for improving the performance of Ti6Al4V alloys, paving the way for advanced medical applications.
基金financially supported by Huxiang Youth Talent Program of Hunan Province(No.2024RC3008)National Natural Science Foundation China(Nos.52274343 and 52474370)National Key R&D Program of China(Nos.2023YFC3903900 and 2023YFC3903904).
文摘Sintering is a critical process in steel production that facilitates the efficient utilization of iron ore resources.However,compared to advanced sintering technologies,China’s sintering methods still exhibit high energy consumption,with typical solid fuel consumption for sintering of about 55 kg/t.In response,a pellet sintering process has been developed and its behavior has been investigated at sintering bed heights of 750 and 1500 mm.Additionally,a technical and economic comparison with traditional sintering methods has been conducted.The results indicate that at a bed height of 750 mm,the pellet sintering method can significantly reduce solid fuel consumption by approximately 30.82%,dropping from 70.75 to 48.95 kg/t.Additionally,the coke rate decreased from 4.55%to 3.20%,and harmful emissions in the flue gas were also reduced.As the bed height increases to 1500 mm,sintering performance improves even further.The coke rate is reduced to 3.00%,and solid fuel consumption decreases to 41.27 kg/t,approaching the world’s advanced level(≤40 kg/t).Technical and economic analysis also indicates that adopting the pellet sintering process can lower sintering costs by about 2.18 dollars/t.
基金supported by the National Natural Science Foundation of China(No.51974131)Hebei Outstanding Youth Fund Project(No.E2020209082),Tangshan Key R&D Program project(No.22150232J)Sixth Division Wujiaqu City Science and Technology Plan Project(2410).
文摘During the sintering process of iron ore,a large amount of nitrogen oxides is generated,for which there is currently no efficient and economical treatment process.Therefore,it is necessary to implement process control in sintering production to keep the mass concentration of NO_(x)in sintering flue gas at a low level.Through industrial trials at sintering sites,methods such as correlation analysis,path analysis,and multiple linear regression were applied to analyze the influence of various factors on NO emissions during the sintering process.The results indicate that negative correlations exist between nitrogen monoxide(NO)emissions and negative pressure,permeability index,O_(2) concentration,CO concentration,and flue gas temperature.Conversely,positive correlations exist between NO emissions and dust concentration,water vapor volume fraction,and sintering bed speed.Among these factors,O_(2) concentration and dust concentration are identified as the most significant influencing factors on NO emissions.By analyzing the masses and modes of influence of different factors,the mechanisms of action of each factor were obtained.Specifically,O_(2) concentration,dust concentration,permeability index,CO concentration,and flue gas temperature play a direct dominant role in NO emissions during the sintering process,while water vapor volume fraction,sintering trolley speed,and negative pressure have an indirect effect.A predictive model for NO mass concentration in flue gas was established with an accuracy rate of 91.6%,showing consistent overall trends with actual values.Finally,denitrification strategies for sintering industrial production were proposed,along with prospects for preliminary denitrification of sintering flue gas using fluidized bed conditions in the duct.
基金supported by Distinguished Professor(Tracking Plan)of Oriental Scholars of Shanghai Universities(Grant No.GZ2020013)National 111 Project(The Program of Introducing Talents of Discipline to University)(Grant No.Dl7002)+1 种基金Independent Research Project of State Key Laboratory of Advanced Special Steel Shanghai Key Laboratory of Advanced Ferrometallurgy and Shanghai University(Grant No.SKLASS 2022-Z011)Additionally,the authors are appreciative of the funding from the Academy of Finland with Grant No.349833.
文摘The mineral composition of the sinter affects the quality of cold-bonded briquettes(CBB),which are prepared from returned sinter fines and serve as a cleaner blast furnace charge.Pulverization rate,compressive strength,reduction disintegration index(RDI)and compressive strength after reduction experiment were tested to analyze the experimental parameters of CBB under the influence of different basicities and sintering time.The results show that when the basicity of CBB is increased from 0.5 to 1.5,the pulverization rate increases,and performance indexes such as compressive strength,RDI,and compressive strength exhibit a decreasing trend.When the basicity is increased from 1.5 to 3.0,all the aforementioned performance indexes are improved.When the sintering time is extended from 0 to 8 h,the properties mentioned above are improved.The results of X-ray diffraction,microstructure,and thermodynamic calculations confirm that the hematite in the mineral composition of CBB tends to convert into calcium ferrite,which leads to the increased compressive strength of CBB.The reasonable basicity and sintering time during sinter preparation not only form the desired mineral composition but also improve the properties of the CBB.
基金supported by Natural Science Foundation of Chongqing(No.CSTB2023NSCQ-BHX0166)Postdoctoral Science Foundation of China(No.2024T171095)Fundamental Research Funds for the Central Universities(No.2024CDJXY003).
文摘Limestone was pretreated via the mechanical activation method,and burnt lime was partially substituted by the pretreated limestone for better sinter indices and lower sintering costs.With the reduction in the size distribution of the pretreated limestone,the particle morphology,the activity of the calcined limestone and the fluidity of the liquid phase during sintering are all improved.When the substitution ratio of the pretreated limestone for burnt lime is kept at 50%,the granulation performance and sinter indices in sinter pot tests are both better compared with that of the base case.Much denser interleaved texture in product sinter is formed with the reduction of sinter porosity and improvement of silico-ferrite of calcium and alumina amount.When the particle size of the pretreated limestone is maintained within the optimal range of 0–2 mm,the tumble index,yield and productivity increase by 7.2%,2.6%and 11.2%,respectively,while the solid fuel rate decreases by 8.7%.In the corresponding sinter industry production,the tumble index and output of the product sinter are comparable to those of the base case,while the coke dosage is reduced by 9.0%.Reduction index and reduction degradation index(RDI_(+3.15))are both higher than 74%.The cost of raw materials in sintering process can be greatly reduced.
基金Project(52274290)supported by the National Natural Science Foundation of ChinaProject(72088101)supported by the Basic Science Center Project for National Natural Science Foundation of China。
文摘A pre-reduction sintering process with flue gas recirculation(PSP_(fsg)-FGR)was developed to mitigate alkalis harm to the blast furnace and reduce the flue gas emission in the whole ironmaking process.The results indicated that the pre-reduction sintering process(PSP)can effectively remove 58.02%of K and 30.68%of Na from raw mixtures and improve yield and tumbler index to 74.40%and 68.69%,respectively.Moreover,PSP was conducive to reducing NO_(x) and SO_(2)emissions and simultaneously increasing CO content in flue gas.Circulating CO-containing flue gas to sintering bed effectively recycled CO and further improved K and Na removal ratio to 74.11%and 32.92%,respectively.Microstructural analysis revealed that the pre-reduced sinter mainly consisted of magnetite,wustite and a small quantity of metallic iron,and very few silicate glass phase was also formed.This process can simultaneously realize alkali metal elements removal as well as flue gas emission reduction from the integrated ironmaking process.
基金supported by the National Key Research and Development Program of China(2022YFC3901405)the National Program for Supporting Postdoctoral Researchers of China(GZC20230016)the 2023 Provincial Quality Project Program for Nurturing People in the New Era(Graduate Education)(2023xscx065).
文摘Volatile organic compounds(VOCs)present significant risks to both human health and the environment.As a result,there has been increasing research on their formation processes,emission patterns,and emission reduction technologies.Sintered ore,a key raw material in ironmaking,requires substantial amounts of fossil fuels such as coal and coke in its production,leading to significant VOC emissions.However,research on VOC emission patterns during the sintering process remains limited.Thus,the influence of factors such as moisture content in the sintering mixture,fuel type,fuel ratio,and coal-to-coke ratio on VOC emissions was investigated through sintering cup experiments.Additionally,the reaction pathways of hydrocarbons within the sintering bed were analyzed using temperature distribution and thermodynamic calculations.In the sintering process using coke powder,the emissions of total volatile organic compounds and non-methane hydrocarbons per ton of sintered ore are 18.78 and 11.14 g,respectively,whereas emissions from coal are substantially higher at 378.27 and 32.55 g.VOC emissions exhibit a linear correlation with the total volatile matter input during sintering,with most VOCs originating from volatile matter.The improved heat transfer conditions reduce the preheating zone thickness,allowing more VOCs to remain in the high-temperature region.
基金supported by the National Natural Science Foundation of China(52204331)Natural Science Foundation of Anhui Province Youth Project(2208085QE145)the Open Project Program of Key Laboratory of Metallurgical Emission Reduction&Resources Recycling(Anhui University of Technology),Ministry of Education(JKF20-03).
文摘Steel rolling sludge,an oil-containing waste generated during steel production,was difficult to manage.Prolonged storage poses significant environmental and health hazards.Most steel enterprises in China use steel rolling sludge directly as a raw material for sintering.However,its adhesive nature caused poor mixing with other materials,affecting the quality of the sinter.Herein,the incorporation of steel rolling sludge incineration slag into the sintering process was investigated for experimental purposes.The results indicated that adding 1%incinerated steel rolling sludge to the sintering raw material was feasible.At this proportion,both the yield and the tumbler index of the sinter have improved,primarily due to the oxidation reaction of Fe_(3)O_(4)present in the steel rolling sludge incineration slag during the sintering process,which significantly increases the sensible heat of the sinter and enhances the sintering mineralization reaction.Notably,the addition of steel rolling sludge incineration slag reduced dioxin concentrations in the sintering flue gas.Although CO,NO_(x),and SO_(2)emission concentrations slightly increased,the existing flue gas treatment system effectively controlled their emissions.
基金supported by the General Program of the National Natural Science Foundation of China(No.52274326)the China Baowu Low Carbon Metallurgy Innovation Foundation(No.BWLCF202109)the Seventh Batch of Ten Thousand Talents Plan of China(No.ZX20220553).
文摘Sinter is the core raw material for blast furnaces.Flue pressure,which is an important state parameter,affects sinter quality.In this paper,flue pressure prediction and optimization were studied based on the shapley additive explanation(SHAP)to predict the flue pressure and take targeted adjustment measures.First,the sintering process data were collected and processed.A flue pressure prediction model was then constructed after comparing different feature selection methods and model algorithms using SHAP+extremely random-ized trees(ET).The prediction accuracy of the model within the error range of±0.25 kPa was 92.63%.SHAP analysis was employed to improve the interpretability of the prediction model.The effects of various sintering operation parameters on flue pressure,the relation-ship between the numerical range of key operation parameters and flue pressure,the effect of operation parameter combinations on flue pressure,and the prediction process of the flue pressure prediction model on a single sample were analyzed.A flue pressure optimization module was also constructed and analyzed when the prediction satisfied the judgment conditions.The operating parameter combination was then pushed.The flue pressure was increased by 5.87%during the verification process,achieving a good optimization effect.
基金the National Key Research and Development Program of China(2017YFB0304301)the Fundamental Research Funds for the Central Universities of Central South University(No.202044016).
文摘Poor permeability and low sintering productivity restrict the development of high-bed sintering.An efficient method of the double-layer sintering process(DLSP)was proposed to achieve high-bed sintering and solve the aforementioned problems.Theoretical calculation and sintering pot experiments were implemented to investigate the double-layer sintering process.Traditional sintering process and DLSP were compared in terms of sintering indices,metallurgical properties and morphology characterization.Under the condition of traditional sintering process,DLSP successfully realized fast velocity and highly productive sintering of 1000-mm high bed.After the sintering bed is charged and ignited twice,the air permeability of the bed has been greatly improved.Sintering time is shortened significantly by simultaneous sintering of the upper and lower feed layers.Under the condition of bed height proportion of 350/650 mm and pre-sintering time of 20 min,the yield,tumbler strength,productivity and solid fuel consumption are 69.96%,65.87%,1.71 t(m^(2)h)^(-1)and 56.71 kg/t,respectively.Magnetite,hematite,calcium ferrite and complex calcium ferrite are the main phases of DLSP products.The metallurgical properties of DSLP products meet the requirement of ironmaking.It indicates that DLSP is an effective method to solve the disadvantages of bad permeability and low sintering productivity in high-bed sintering.
基金supported by the Basic Science Center Project for the National Natural Science Foundation of China(No.72088101)the S&T Program of Hebei(No.23564101D).
文摘As the bed depth increases,sintering yield increases,but the productivity decreases.To reveal the reasons for the decrease in productivity and explore targeted solutions,the bed resistance of mixtures,wet zone,and combustion zone was analyzed in the laboratory.The results showed that the decreased porosity of mixture resulted in the increased bed resistance by 160.56%when the bed depth increased from 600 to 1000 mm.After improving porosity of 1%by adding loosening bars with optimized size and distribution,the bed resistance decreased,and the productivity increased by 5%.The increase in bed depth increased the thickness of the wet zone from 120 to 680 mm and the resistance from 1.56 to 8.83 kPa.By using a three-stage intensive mixer and pre-adding water for granulation,the moisture of mixture was reduced by 0.6%,and the sintering productivity increased by 4%.Besides,the high bed resistance is mainly caused by the increase in the thickness of the combustion zone from 31.9 to 132.7 mm,and the bed resistance increased from 0.70 to 5.62 kPa.The bed resistance of the combustion zone at 900 mm was increased by 90.51%compared to 700 mm.After optimization of the distribution of coke breeze,the thickness of combustion zone at the lower layer decreased from 132.7 to 106.84 mm and permeability improved significantly.
文摘A key component of future lunar missions is the concept of in-situ resource utilization(ISRU),which involves the use of local resources to support human missions and reduce dependence on Earth-based supplies.This paper investigates the thermal processing capability of lunar regolith without the addition of binders,with a focus on large-scale applications for the construction of lunar habitats and infrastructure.The study used a simulant of lunar regolith found on the Schr?dinger Basin in the South Pole region.This regolith simulant consists of20 wt%basalt and 80 wt%anorthosite.Experiments were conducted using a high power CO_(2)laser to sinter and melt the regolith in a 80 mm diameter laser spot to evaluate the effectiveness of direct large area thermal processing.Results indicated that sintering begins at approximately 1180℃and reaches full melt at temperatures above 1360℃.Sintering experiments with this material revealed the formation of dense samples up to 11 mm thick,while melting experiments successfully produced larger samples by overlapping molten layers and additive manufacturing up to 50 mm thick.The energy efficiency of the sintering and melting processes was compared.The melting process was about 10 times more energy efficient than sintering in terms of material consolidation,demonstrating the promising potential of laser melting technologies of anorthosite-rich regolith for the production of structural elements.
基金founded by the Open Project Program of Anhui Province Key Laboratory of Metallurgical Engineering and Resources Recycling(Anhui University of Technology)(No.SKF21-06)Research Fund for Young Teachers of Anhui University of Technology in 2020(No.QZ202001).
文摘Real-time prediction and precise control of sinter quality are pivotal for energy saving,cost reduction,quality improvement and efficiency enhancement in the ironmaking process.To advance,the accuracy and comprehensiveness of sinter quality prediction,an intelligent flare monitoring system for sintering machine tails that combines hybrid neural networks integrating convolutional neural network with long short-term memory(CNN-LSTM)networks was proposed.The system utilized a high-temperature thermal imager for image acquisition at the sintering machine tail and employed a zone-triggered method to accurately capture dynamic feature images under challenging conditions of high-temperature,high dust,and occlusion.The feature images were then segmented through a triple-iteration multi-thresholding approach based on the maximum between-class variance method to minimize detail loss during the segmentation process.Leveraging the advantages of CNN and LSTM networks in capturing temporal and spatial information,a comprehensive model for sinter quality prediction was constructed,with inputs including the proportion of combustion layer,porosity rate,temperature distribution,and image features obtained from the convolutional neural network,and outputs comprising quality indicators such as underburning index,uniformity index,and FeO content of the sinter.The accuracy is notably increased,achieving a 95.8%hit rate within an error margin of±1.0.After the system is applied,the average qualified rate of FeO content increases from 87.24%to 89.99%,representing an improvement of 2.75%.The average monthly solid fuel consumption is reduced from 49.75 to 46.44 kg/t,leading to a 6.65%reduction and underscoring significant energy saving and cost reduction effects.
基金supported by the National Key R&D Pro-gram of China(No.2022YFB3805701)National Natural Science Foundation of China(NSFC)(No.52371182,51701052,52192592,52192593)+1 种基金Young Elite Scientists Sponsorship Program by CAST(No.2019QNRC001)the Heilongjiang Touyan Innovation Team Program.
文摘1.Introduction.Ni-Mn-X(X=Ga,In,Sn,or Sb)Heusler alloys have versatile properties[1-4],such as shape memory effect[1],superelastic-ity[5],magnetocaloric effect[3],elastocaloric effect[6],and even multicaloric effect[7],that indicate their potential for use in actu-ators,sensors,micropumps,energy harvesters,and solid-state re-frigeration[8-10].Among the alloys,Ni-Mn-Sn-based alloys are environment-friendly and cost-effective[6,7,11],and hence,they have received widespread attention.
基金Natural Science Foundation of Shanghai(24ZR1400800)he Natural Science Foundation of China(U23A20685,52073058,91963204)+1 种基金the National Key R&D Program of China(2021YFB3701400)Shanghai Sailing Program(23YF1400200)。
文摘High-performance graphite materials have important roles in aerospace and nuclear reactor technologies because of their outstanding chemical stability and high-temperature performance.Their traditional production method relies on repeated impregnation-carbonization and graphitization,and is plagued by lengthy preparation cycles and high energy consumption.Phase transition-assisted self-pressurized selfsintering technology can rapidly produce high-strength graphite materials,but the fracture strain of the graphite materials produced is poor.To solve this problem,this study used a two-step sintering method to uniformly introduce micro-nano pores into natural graphite-based bulk graphite,achieving improved fracture strain of the samples without reducing their density and mechanical properties.Using natural graphite powder,micron-diamond,and nano-diamond as raw materials,and by precisely controlling the staged pressure release process,the degree of diamond phase transition expansion was effectively regulated.The strain-to-failure of the graphite samples reached 1.2%,a 35%increase compared to samples produced by fullpressure sintering.Meanwhile,their flexural strength exceeded 110 MPa,and their density was over 1.9 g/cm^(3).The process therefore produced both a high strength and a high fracture strain.The interface evolution and toughening mechanism during the two-step sintering process were investigated.It is believed that the micro-nano pores formed have two roles:as stress concentrators they induce yielding by shear and as multi-crack propagation paths they significantly lengthen the crack propagation path.The two-step sintering phase transition strategy introduces pores and provides a new approach for increasing the fracture strain of brittle materials.
基金Student Training Program for Innovation and Entrepreneurship of Hangzhou Institute for Advanced Study,UCAS(CXCY20230305)Chinese Academy of Sciences Key Project(ZDRW-CN-2021-3-1-18)。
文摘Ceramic dielectric materials with high dielectric strength and mechanisms of their internal factors affecting dielectric strength are significantly valuable for industrial application,especially for selection of suitable dielectric materials for high-power microwave transmission devices and reliable power transmission.Pure magnesium oxide(MgO),a kind of ceramic dielectric material,possesses great application potential in high-power microwave transmission devices due to its high theoretical dielectric strength,low dielectric constant,and low dielectric loss properties,but its application is limited by high sintering temperature during preparation.This work presented the preparation of a new type of multiphase ceramics based on MgO,which was MgO-1%ZrO_(2)-1%CaCO_(3-x)%MnCO_(3)(MZCM_(x),x=0,0.25,0.50,1.00,1.50,in molar),and their phase structures,morphological features,and dielectric properties were investigated.It was found that inclusion of ZrO_(2) and CaCO_(3) effectively inhibited excessive growth of MgO grains by formation of second phase,while addition of MnCO_(3) promoted the grain boundary diffusion process during the sintering process and reduced activation energy for the grain growth,resulting in a lower ceramic sintering temperature.Excellent performance,including high dielectric strength(Eb=92.3 kV/mm)and quality factor(Q×f=216642 GHz),simultaneously accompanying low dielectric loss(<0.03%),low temperature coefficient of dielectric constant(20.3×10^(–6)℃^(–1),85℃)and resonance frequency(–12.54×10^(–6)℃^(–1)),was achieved in MZCM1.00 ceramics under a relatively low sintering temperature of 1350℃.This work offers an effective solution for selecting dielectric materials for high-power microwave transmission devices.
基金Key Research and Development Program of Shandong Province(2021CXGC010310)Shandong Province Science and Technology Small and Medium Sized Enterprise Innovation Ability Enhancement Project(2023TSGC0287,2024TSGC0519)+1 种基金Shandong Provincial Natural Science Foundation(ZR2022ME222)National Natural Science Foundation of China(51702187)。
文摘Three types of NdFeB magnets with the same composition and different grain sizes were prepared,and then the grain boundary diffusion was conducted using metal Tb under the same technical parameters.The effect of grain size on the grain boundary diffusion process and properties of sintered NdFeB magnets was investigated.The diffusion process was assessed using X-ray diffractometer,field emission scanning electron microscope,and electron probe microanalyzer.The magnetic properties of the magnet before and after diffusion were investigated.The results show that the grain refinement of the magnet leads to higher Tb utilization efficiency and results in higher coercivity at different temperatures.It can be attributed to the formation of a deeper and more complete core-shell structure,resulting in better magnetic isolation and higher anisotropy of the Nd_(2)Fe_(14)B grains.This work may shed light on developing high coercivity with low heavy rare earth elements through grain refinement.
基金National Natural Science Foundation of China (U24A2052)Shanghai Eastern Talent Plan。
文摘ZnAl_(2)O_(4) and ZnAl_(2)O_(4)-based ceramics have attracted much attention from researchers due to their good microwave dielectric,thermal and mechanical properties.In this work,the influence of 5%(in mass)CuO-TiO_(2)-Nb_(2)O_(5)(CTN)ternary composite oxide additives with different composition ratios on sintering behavior and properties of ZnAl_(2)O_(4) microwave dielectric ceramics was investigated.When the molar fraction ranges of Cu,Ti and Nb elements in 5%CTN additives are 0.625-0.875,0-0.250 and 0.125-0.625,respectively,sintering temperature of ZnAl_(2)O_(4) ceramics can be reduced from above 1400℃to below 1000℃.The sintering additives CN(Cu:Nb=1:1,molar ratio)and CTN(Cu:Ti:Nb=4:1:3,molar ratio)can reduce sintering temperature of ZnAl_(2)O_(4) ceramics to 975 and 1000℃,respectively,while maintaining good dielectric properties(dielectric constantε_(r)=11.36,quality factor Q׃=8245 GHz andε_(r)=9.52,Q׃=22249 GHz)and flexural strengths(200 and 161 MPa),which are expected to be applied in preparation of low temperature co-fired ceramic(LTCC)materials with copper electrodes.Low-temperature sintering of the ZnAl_(2)O_(4)+CTN system is characterized as activated sintering.Nanometer-level amorphous interfacial films containing Cu,Ti,and Nb elements are observed at the grain boundaries,which may provide fast diffusion pathways for mass transportation during the sintering process.Valence changes of Ti and Cu ions,along with changes of oxygen vacancies,are confirmed,which provides a potential mechanism for reduced sintering temperature of ZnAl_(2)O_(4) ceramics.In addition,a series of reactions occurring at the grain boundaries can activate these boundaries and further promote the sintering densification process.These results suggest a promising way to design a novel LTCC material with excellent properties based on the low temperature sintering of ceramics with the sintering aid of CuO-TiO_(2)-Nb_(2)O_(5) composite oxide.
基金Project (50930005) supported by the National Natural Science Foundation of ChinaProject (U0834002) supported by the Key Programof NSFC-Guangdong Joint Funds of China+1 种基金Project (LYM09024) supported by Training Program for Excellent Young Teachers withInnovation of Guangdong University, ChinaProject (2009ZM0121) supported by the Fundamental Research Funds for the CentralUniversities of South China University of Technology,China
文摘A procedure of low temperature solid-phase sintering（LTSS） was carried out to fabricate sintered metal fibrous media（SMFM） with high specific surface area.Stainless steel fibers which were produced by cutting process were first plated with a coarse copper coating layer by electroless plating process.A low-temperature sintering process was then completed at about 800 °C for 1 h under the protection of hydrogen atmosphere.The results show that a novel SMFM with complex surface morphology and high specific surface area（0.2 m2/g） can be obtained in this way.The effect of sintering temperature on the surface morphology and specific surface area of SMFM was studied by means of scanning electron microscopy and Brunauer-Emmett-Teller.The damage of micro-structure during the sintering process mainly contributed to the loss of specific surface area of SMFM and the optimal sintering temperature was 800 °C.
基金supported by the National Natural Science Foundation of China(Nos.52261037,52088101)the Key research project of Jiangxi Province(No.20203ABC28W006)the Double-Thousand Plan of Jiangxi Province(No.jxsq2023101057).
文摘The low coercivity is the major factor inhibiting the large-scale commercial utilization of Nd-Ce-Fe-B sintered magnets.In this work,we achieved a record-high coercivity of 15.04 kOe in Ga-doped Nd-Ce-Fe-B sintered magnets with 30 wt%Ce replacing Nd,demonstrating enormous potential.The Ga-doped Nd-Ce-Fe-B magnets with higher boron(HB)and lower boron(LB)content are designed.The coercivity of the HB magnet increases slightly from 10.80 to 12.26 kOe after annealing,attributed to the optimized distribution of grain boundary(GB)phases.In contrast,the coercivity of the LB magnet remarkably increases from 8.13 to 15.04 kOe after annealing.Microstructural observations indicate that the narrow GB phase in the as-sintered magnet is rich in Fe,and the strong exchange coupling of adjacent grains resulted in low coercivity.The evolution of Ga-rich phases reveals a potential formation mechanism of the RE_(6)Fe_(13)Ga phase,that is the RE-Fe amorphous phase and REGa phase in the as-sintered magnet combine to form the RE_(6)Fe_(13)Ga phase and RE-Ga amorphous phase during post-sinter annealing(RE:rare earth).Moreover,the GB phase of the annealed magnet transforms into a Fe-lean phase with a thickness of 16.4 nm.Magnetization and demagnetization behavior characterizations reveal that the exchange decoupling of adjacent grains induced by the optimized GB phases is the main reason for the remarkable coercivity enhancement,which is also validated by micromagnetic simulations.
