Rectifiers with high efficiency and high power density are crucial to the stable and efficient power supply of 5G communication base stations,which deserves in-depth investigation.In general,there are two key problems...Rectifiers with high efficiency and high power density are crucial to the stable and efficient power supply of 5G communication base stations,which deserves in-depth investigation.In general,there are two key problems to be addressed:supporting both alternating current(AC)and direct current(DC)input,and minimizing the common-mode voltage as well as leakage current for safety reasons.In this paper,a hybrid five-level single-phase rectifier is proposed.A five-level topology is adopted in the upper arm,and a half-bridge diode topology is adopted in the lower arm.A dual closed-loop control strategy and a flying capacitor voltage regulation method are designed accordingly so that the compatibility of both AC and DC input is realized with low common voltage and small passive devices.Simulation and experimental results demonstrate the effectiveness and performance of the proposed rectifier.展开更多
The Vienna rectifier is a widely adopted solution for high-power rectification due to its efficiency and straightforward design.However,its performance can degrade under unbalanced three phase voltage conditions,leadi...The Vienna rectifier is a widely adopted solution for high-power rectification due to its efficiency and straightforward design.However,its performance can degrade under unbalanced three phase voltage conditions,leading to current zero-crossing distortion and compromised dynamic response.This paper investigates the causes of these distortions,identifying a phase shift between the input current and the grid voltage as a primary factor,and proposes an effective distortion phase identification strategy.Furthermore,the dynamic performance is enhanced through improved current reference calculations and a refined power feedforward strategy.This approach optimizes the system's response to load changes and maintains output voltage stability under unbalanced conditions.Simulation results validate the effectiveness of the proposed methods in reducing current distortion and improving overall performance.展开更多
In order to increase the stability of the Mongolia power system, a single-phase automatic reclosing device (SPAR) was introduced on double-circuit power lines built with a size of 330 kV, operating on a voltage of 220...In order to increase the stability of the Mongolia power system, a single-phase automatic reclosing device (SPAR) was introduced on double-circuit power lines built with a size of 330 kV, operating on a voltage of 220 kV and a length of 250 km. These overhead power lines (L-213, L-214) connect the 220/110/35 kV “Songino” substation with the “Mandal” substation and form system networks. This paper presents the challenges encountered when implementing single-phase automatic reclosing (SPAR) devices and compares the changes in power system parameters before and after SPAR deployment for a long 220 kV line. Simulations and analyses were carried out using DIgSILENT PowerFactory software, focusing on rotor angle stability, and the overall impact on the power system during short-circuit faults. The evaluation also utilized measurement data from the Wide Area Monitoring System (WAMS) to compare system behavior pre- and post-implementation of SPAR. The findings reveal that SPAR significantly enhances system reliability and stability, effectively mitigating the risk of oscillations and stability loss triggered by short circuits. This improvement contributes to a more resilient power system, reducing the potential for disturbances caused by faults.展开更多
In this study,Computational Fluid Dynamics(CFD)together with a component transport model are exploited to investigate the influence of dimensionless parameters,involving the height of the rectifier grid and the instal...In this study,Computational Fluid Dynamics(CFD)together with a component transport model are exploited to investigate the influence of dimensionless parameters,involving the height of the rectifier grid and the installation height of the first catalyst layer,on the flow field and the overall denitration efficiency of a cement kiln’s SCR(Selective catalytic reduction)denitrification reactor.It is shown that accurate numerical results can be obtained by fitting the particle size distribution function to the actual cement kiln fly ash and implementing a non-uniform particle inlet boundary condition.The relative error between denitration efficiency derived from experimental data,numerical simulation,and real-time system pressure drop ranges from 4%to 9%.Optimization of the SCR reactor is achieved when the rectifier grid thickness ratio k/H≥0.030,the rectifier grid height ratio h/H=0.04,and the spacing between the rectifier grid and the first catalyst layer l/H=0.10.Under these conditions,airflow distribution and particle dispersion upstream of the catalyst result in increased denitration efficiencies of 3.21%,3.43%,and 3.27%,respectively,compared to the least favorable operating conditions.展开更多
Based on a neutral point diode clamped eight-switch configuration, a general mathematical model of single phase bi-directional three-level (TL) rectifiers is built by proposing two equivalent TL arms for topology deri...Based on a neutral point diode clamped eight-switch configuration, a general mathematical model of single phase bi-directional three-level (TL) rectifiers is built by proposing two equivalent TL arms for topology derivation. A series of TL rectifiers are derived by using double TL and multi TL methods, and their characteristics are compared at the same time. A novel seven-switch double TL rectifier is constructed, and its operational principle and control algorithm are illustrated as well. Lastly, its waveform and harmonic spectrum are compared to those of multi TL rectifiers, and the adopted rectifier gains better performance and unit PF.展开更多
This paper proposes and implements a model-free open-loop iterative learning control(ILC)strategy to realize the speed control of the single-phase flux switching motor(FSM)with an asymmetrical rotor.Base on the propos...This paper proposes and implements a model-free open-loop iterative learning control(ILC)strategy to realize the speed control of the single-phase flux switching motor(FSM)with an asymmetrical rotor.Base on the proposed winding control method,the asymmetrical rotor enables the motor to generate continuous positive torque for positive rotation,and relatively small resistance torque for negative rotation.An initial iteration coefficient and variable iteration coefficient optimized scheme was proposed based on the characteristics of the hardware circuit,thereby forming the model-free strategy.A series of prototype experiments was carried out.Experimental results verify the effectiveness and practicability of the proposed ILC strategy.展开更多
The information of the field current is essential for the brushless synchronous starter/generator system,which determines the performance and health status of this system.However,since the field winding of the main ma...The information of the field current is essential for the brushless synchronous starter/generator system,which determines the performance and health status of this system.However,since the field winding of the main machine is installed in the rotor part,the measurement of the field current in this brushless system seem impossible.Considering that,the field current might be affected by the rectifier mode,the field current estimation method in different rectifier mode is studied in this paper.The main exciter(ME)rotor currents were restructured based on the ME flux equations.With these restructured rotor currents,the field current in different rectifier commutation mode is analyzed,then the field current estimation method considering the rectifier mode can be obtained.The experiments in different rectifier modes are carried out to verify the proposed method.展开更多
The face velocities of the high efficiency particulate air filters and the ultra low penetration airfilters in fan filter units (FFUs) have large relative standard deviation and turbulivity. It seriously affects the ...The face velocities of the high efficiency particulate air filters and the ultra low penetration airfilters in fan filter units (FFUs) have large relative standard deviation and turbulivity. It seriously affects the unidirectivity of the flow in the unidirectional flow clean zone and cleanroom. The cross contamination in this kind of unidirectional flow area is hardly controlled. It is significant to find optional method for keeping the face velocity uniformity of FFU and reducing the face velocity turbulivity of FFU, furthermore, to keep the cleanliness level under FFUs. The normal and easy method is to add flow rectifiers under filters. FFUs with various flow rectifiers have been tested. The uniformity and turbulivity of facevelocity under the FFU are presented in this paper. The influence of the facevelocity uniformity and turbulivity on the contamination boundary of the unidirectional flow is studiedas well.展开更多
On the basis of detailed analysis of a novel harmonic counteracting method which can be used to effectively compensate the supply line harmonic currents of a passive single phase diode bridge rectifier, this paper pr...On the basis of detailed analysis of a novel harmonic counteracting method which can be used to effectively compensate the supply line harmonic currents of a passive single phase diode bridge rectifier, this paper presents two simpler single phase diode bridge rectifier configurations and their alternatives which can achieve low supply line current THD(total harmonic distortion) too. Moreover, this paper also proposes a few passive hamonic counteracting networks for multi single phase rectifiers which are connected in parallel.展开更多
A novel white-light emitting single-phase phosphor La_3 Si_6 N_(11):Dy^(3+),exhibiting two emission peaks centering at 475 and 575 nm, was prepared via conventional solid-state reactions. The structure and morphology ...A novel white-light emitting single-phase phosphor La_3 Si_6 N_(11):Dy^(3+),exhibiting two emission peaks centering at 475 and 575 nm, was prepared via conventional solid-state reactions. The structure and morphology of La_3 Si_6 N_(11):Dy^(3+)/Tb^(3+) were investigated by X-ray diffraction(XRD) and scanning electron microscopy(SEM). The emission colors can be tuned from white to yellow-green through increasing the Tb^(3+) concentration in La_3 Si_6 N_(11):Dy^(3+),Tb^(3+), The mechanism of energy transfer(ET) from Dy^(3+) to Tb^(3+) is confirmed according to the excitation,emission spectra and decay lifetimes curve. The temperaturedependent luminescence measurements of La_(2.83)Si_6 N_(11):0.1 Dy^(3+),0.07 Tb^(3+) were also performed, and a good thermal stability is shown, suggesting superior properties for the application as white lightemitting diodes(w-LEDs) phosphor.展开更多
Due to low investment cost and high reliability,a new scheme called DR-HVDC(Diode Rectifier based HVDC)transmission was recently proposed for grid integration of large offshore wind farms.However,in this scheme,the ap...Due to low investment cost and high reliability,a new scheme called DR-HVDC(Diode Rectifier based HVDC)transmission was recently proposed for grid integration of large offshore wind farms.However,in this scheme,the application of conventional control strategies for stability operation face several challenges due to the uncontrollability of the DR.In this paper,a coordinated control strategy of offshore wind farms using the DR-HVDC transmission technology to connect with the onshore grid,is investigated.A novel coordinated control strategy for DR-HVDC is proposed based on the analysis of the DC current control ability of the full-bridge-based modular multilevel converter(FB-MMC)at the onshore station and the input and output characteristics of the diode rectifier at the offshore.Considering the characteristics of operation stability and decoupling between reactive power and active power,a simplified design based on double-loop droop control for offshore AC voltage is proposed after power flow and voltage–current(I–V)characteristics of the offshore wind farm being analyzed.Furthermore,the impact of onshore AC fault to offshore wind farm is analyzed,and a fast fault detection and protection strategy without relying on communication is proposed.Case studies carried out by PSCAD/EMTDC verify the effectiveness of the proposed control strategy for the start up,power fluctuation,and onshore and offshore fault conditions.展开更多
The Auto-Transformer Rectifier Unit（ATRU） is one preferred solution for high-power AC/DC power conversion in aircraft. This is mainly due to its simple structure, high reliability and reduced k VA ratings. Indeed, t...The Auto-Transformer Rectifier Unit（ATRU） is one preferred solution for high-power AC/DC power conversion in aircraft. This is mainly due to its simple structure, high reliability and reduced k VA ratings. Indeed, the ATRU has become a preferred AC/DC solution to supply power to the electric environment control system on-board future aircraft. In this paper, a general modelling method for ATRUs is introduced. The developed model is based on the fact that the DC voltage and current are strongly related to the voltage and current vectors at the AC terminals of ATRUs. In this paper, we carry on our research in modelling symmetric 18-pulse ATRUs and develop a generic modelling technique. The developed generic model can study not only symmetric but also asymmetric ATRUs. An 18-pulse asymmetric ATRU is used to demonstrate the accuracy and efficiency of the developed model by comparing with corresponding detailed switching SABER models provided by our industrial partner. The functional models also allow accelerated and accurate simulations and thus enable whole-scale more-electric aircraft electrical power system studies in the future.展开更多
The microstructure,mechanical property,and in vitro biocorrosion behavior of as-cast single-phase biodegradable Mg-1.5Zn-0.6Zr alloy were investigated and compared with a commercial as-cast AZ91D alloy.The results sho...The microstructure,mechanical property,and in vitro biocorrosion behavior of as-cast single-phase biodegradable Mg-1.5Zn-0.6Zr alloy were investigated and compared with a commercial as-cast AZ91D alloy.The results show that the Mg-1.5Zn-0.6Zr alloy had a single-phase solid solution structure,with an average grain size of 34.7±13.1μm.The alloy exhibited ultimate tensile strength of 168±2.0 MPa,yield strength of 83±0.6 MPa,and elongation of 9.1±0.6%.Immersion tests and electrochemical measurements reveal that the alloy displayed lower biocorrosion rate and more uniform corrosion mode than AZ91D in Hank's solution.The elimination of intensive galvanic corrosion reactions and the formation of a much more compact and uniform corrosion film mainly account for the better biocorrosion properties of the Mg-1.5Zn-0.6Zr alloy than AZ91D.展开更多
This paper describes the successful fabrication of 4H-SiC junction barrier Schottky （JBS） rectifiers with a linearly graded field limiting ring （LG-FLR）. Linearly variable ring spacings for the FLR termination are...This paper describes the successful fabrication of 4H-SiC junction barrier Schottky （JBS） rectifiers with a linearly graded field limiting ring （LG-FLR）. Linearly variable ring spacings for the FLR termination are applied to improve the blocking voltage by reducing the peak surface electric field at the edge termination region, which acts like a variable lateral doping profile resulting in a gradual field distribution. The experimental results demonstrate a breakdown voltage of 5 kV at the reverse leakage current density of 2 mA/cm2 （about 80% of the theoretical value）. Detailed numerical simulations show that the proposed termination structure provides a uniform electric field profile compared to the conventional FLR termi- nation, which is responsible for 45% improvement in the reverse blocking voltage despite a 3.7% longer total termination length.展开更多
The principle of single to single phase matrix electric power conversioin is further studied and the conversioin switch function is introduced into conventional rectifier inverter, thus a general character of the t...The principle of single to single phase matrix electric power conversioin is further studied and the conversioin switch function is introduced into conventional rectifier inverter, thus a general character of the two conversion techniques is discovered. It is characteristic of the switch functiion to follow mains voltage distortion and mains frequency drift. By utilizing the merit, unidirectional switch duty rations of the inverter follow the variation of DC link voltage automatically, thus the size of DC link electrolytic capacitor can be reduced considerably, bringing about improved mains side power factor. Corresponding topologies and theoretical and theoretical derivations are given, and so are the simulation results, based on which it is confirmed that the single to single phase matrix conversion technique is potentially useful in large scale production, and the introduction of switch function can yield good economic returns.展开更多
This study focuses on the effects of rotational and welding speeds on the microstructure and hardness of joints in friction stir welded single-phase brass. Welds were achieved under low heat input conditions at rotati...This study focuses on the effects of rotational and welding speeds on the microstructure and hardness of joints in friction stir welded single-phase brass. Welds were achieved under low heat input conditions at rotational and welding speeds of 400-800 r/min and 100-300 mm/min, respectively. In order to characterize the obtained welds, optical microscopy and Vickers hardness measurements were taken on the weld cross sections. According to the obtained results, increasing the welding speed and/or decreasing the rotational speed caused the grain size of the stir zone to decrease and, hence, improved the average hardness of this region. These results are discussed with respect to the interplay between the welding parameters and the peak temperature in the weld thermal cycle.展开更多
An improved structure of Schottky rectifier, called a trapezoid mesa trench metal oxide semiconductor （MOS） barrier Schottky rectifier （TM-TMBS）, is proposed and studied by two-dimensional numerical simulations. B...An improved structure of Schottky rectifier, called a trapezoid mesa trench metal oxide semiconductor （MOS） barrier Schottky rectifier （TM-TMBS）, is proposed and studied by two-dimensional numerical simulations. Both forward and especially better reverse I-V characteristics, including lower leakage current and higher breakdown voltage, are demonstrated by comparing our proposed TM-TMBS with a regular trench MOS barrier Schottky rectifier （TMBS） as well as a conventional planar Schottky barrier diode rectifier. Optimized device parameters corresponding to the requirement for high breakdown voltage are given. With optimized parameters, TM-TMBS attains a breakdown voltage of 186 V, which is 6.3% larger than that of the optimized TMBS, and a leakage current of 4.3×10^-6 A/cm2, which is 26% smaller than that of the optimized TMBS. The relationship between optimized breakdown voltage and some device parameters is studied. Explanations and design rules are given according to this relationship.展开更多
The Vienna rectifier with unbalanced input voltage and load transient is analyzed.A nonlinear control strategy for Vienna rectifier under unbalanced input is proposed.From the view of positive and negative sequence co...The Vienna rectifier with unbalanced input voltage and load transient is analyzed.A nonlinear control strategy for Vienna rectifier under unbalanced input is proposed.From the view of positive and negative sequence components,the proposed nonlinear control strategy suppresses the twice frequency ripple and guarantees the dynamic response characteristic at the same time.Thanks to the proposed nonlinear control strategy,the DC bus capacitor can be reduced a lot since the voltage ripple and drop can be suppressed.A 10 kW Vienna rectifier is built to verify the proposed control strategy.After applying the proposed nonlinear control strategy,the voltage ripple is only7 V and decreases over 75%over the traditional PI control when the unbalanced degree is 20%.The voltage drop can be reduced about 80%than former control strategy which is helpful to reduce the DC bus capacitor and achieve higher power density.The volume of the capacitor can be reduced by 83.3%with the new control method.展开更多
The effect of the mesa configuration on the reverse breakdown characteristic of a SiC PiN rectifier for high-voltage applications is analyzed in this study.Three geometrical parameters,i.e.,mesa height,mesa angle and ...The effect of the mesa configuration on the reverse breakdown characteristic of a SiC PiN rectifier for high-voltage applications is analyzed in this study.Three geometrical parameters,i.e.,mesa height,mesa angle and mesa bottom corner,are investigated by numerical simulation.The simulation results show that a deep mesa height,a small mesa angle and a smooth mesa bottom（without sub-trench） could contribute to a high breakdown voltage due to a smooth and uniform surface electric field distribution.Moreover,an optimized mesa structure without sub-trench（mesa height of 2.2 μm and mesa angle of 20°） is experimentally demonstrated.A maximum reverse blocking voltage of 4 kV and a forward voltage drop of 3.7 V at 100 A/cm^2 are obtained from the fabricated diode with a 30-μm thick N^- epi-layer,corresponding to 85% of the ideal parallel-plane value.The blocking characteristic as a function of the JTE dose is also discussed for the PiN rectifiers with and without interface charge.展开更多
The aim of this study was to compare the effects of d, l-Sotalol and dSotalol on the delayed rectifier K+ outward current in the presence of isoproterenol at different concentrations. Time-dependent delayed rectifier...The aim of this study was to compare the effects of d, l-Sotalol and dSotalol on the delayed rectifier K+ outward current in the presence of isoproterenol at different concentrations. Time-dependent delayed rectifier K+ outward currents were measured in isolated guinea pig single myocytes using the whole-cell configuration of the patch-clamp technique. Currents were measured in response to 300 ms depolarizing pulses from a holding potential of -40 mV in three experimental protocols [control, isoproterenol (10^(9)mol/L - 10^(-6) mol/L ), and isoproterenol (10^(-9)mol/L - 10^(-6)mol/L ) plus either d, l-Sotalol (10^(-4) mol/L) or d-Sotalol (10^(-4) mol/L)]. IK tail currents were measured upon repolarization to -40 mV. It was found that Ik was significantly amplified in the presence. of isoproterenol (10^(-9) mol/L- 10^(-6) mol/L) plus d-Sotalol. At 10-8 mol/L isoproterenol, Ik was increased by 92. 7%±17. 1 % (P<0. 05) and 54. 3 %±13. 4 % after d-Sotalol addition (P<0. 05). In contrast, d, l-Sotalol completely conteracted the increase of iK by isoproterenol (<10^(-8) mol/L), and compared to control, Ic was decreased by 35. 6 % ±8. 1% at 10^(-8) mol/L isoproterenol plus d, l-Sotalol (P<0. 05). It is concluded that the β-adrenergic blocking property of d, l-Sotalol but not that of dSotalol maintains the delayed rectifier K+ outward current blockade in the presence of isoproterenol in guinea pig myocytes. This might contribute to a superior antiarrhythmic efficacy as compared to d-Sotalol.展开更多
文摘Rectifiers with high efficiency and high power density are crucial to the stable and efficient power supply of 5G communication base stations,which deserves in-depth investigation.In general,there are two key problems to be addressed:supporting both alternating current(AC)and direct current(DC)input,and minimizing the common-mode voltage as well as leakage current for safety reasons.In this paper,a hybrid five-level single-phase rectifier is proposed.A five-level topology is adopted in the upper arm,and a half-bridge diode topology is adopted in the lower arm.A dual closed-loop control strategy and a flying capacitor voltage regulation method are designed accordingly so that the compatibility of both AC and DC input is realized with low common voltage and small passive devices.Simulation and experimental results demonstrate the effectiveness and performance of the proposed rectifier.
文摘The Vienna rectifier is a widely adopted solution for high-power rectification due to its efficiency and straightforward design.However,its performance can degrade under unbalanced three phase voltage conditions,leading to current zero-crossing distortion and compromised dynamic response.This paper investigates the causes of these distortions,identifying a phase shift between the input current and the grid voltage as a primary factor,and proposes an effective distortion phase identification strategy.Furthermore,the dynamic performance is enhanced through improved current reference calculations and a refined power feedforward strategy.This approach optimizes the system's response to load changes and maintains output voltage stability under unbalanced conditions.Simulation results validate the effectiveness of the proposed methods in reducing current distortion and improving overall performance.
文摘In order to increase the stability of the Mongolia power system, a single-phase automatic reclosing device (SPAR) was introduced on double-circuit power lines built with a size of 330 kV, operating on a voltage of 220 kV and a length of 250 km. These overhead power lines (L-213, L-214) connect the 220/110/35 kV “Songino” substation with the “Mandal” substation and form system networks. This paper presents the challenges encountered when implementing single-phase automatic reclosing (SPAR) devices and compares the changes in power system parameters before and after SPAR deployment for a long 220 kV line. Simulations and analyses were carried out using DIgSILENT PowerFactory software, focusing on rotor angle stability, and the overall impact on the power system during short-circuit faults. The evaluation also utilized measurement data from the Wide Area Monitoring System (WAMS) to compare system behavior pre- and post-implementation of SPAR. The findings reveal that SPAR significantly enhances system reliability and stability, effectively mitigating the risk of oscillations and stability loss triggered by short circuits. This improvement contributes to a more resilient power system, reducing the potential for disturbances caused by faults.
基金Anhui Province Key Research and Development Plan of the Ecological Environment Project(No.202104i07020016).
文摘In this study,Computational Fluid Dynamics(CFD)together with a component transport model are exploited to investigate the influence of dimensionless parameters,involving the height of the rectifier grid and the installation height of the first catalyst layer,on the flow field and the overall denitration efficiency of a cement kiln’s SCR(Selective catalytic reduction)denitrification reactor.It is shown that accurate numerical results can be obtained by fitting the particle size distribution function to the actual cement kiln fly ash and implementing a non-uniform particle inlet boundary condition.The relative error between denitration efficiency derived from experimental data,numerical simulation,and real-time system pressure drop ranges from 4%to 9%.Optimization of the SCR reactor is achieved when the rectifier grid thickness ratio k/H≥0.030,the rectifier grid height ratio h/H=0.04,and the spacing between the rectifier grid and the first catalyst layer l/H=0.10.Under these conditions,airflow distribution and particle dispersion upstream of the catalyst result in increased denitration efficiencies of 3.21%,3.43%,and 3.27%,respectively,compared to the least favorable operating conditions.
基金National Nature Science Foundation of China(50277017)
文摘Based on a neutral point diode clamped eight-switch configuration, a general mathematical model of single phase bi-directional three-level (TL) rectifiers is built by proposing two equivalent TL arms for topology derivation. A series of TL rectifiers are derived by using double TL and multi TL methods, and their characteristics are compared at the same time. A novel seven-switch double TL rectifier is constructed, and its operational principle and control algorithm are illustrated as well. Lastly, its waveform and harmonic spectrum are compared to those of multi TL rectifiers, and the adopted rectifier gains better performance and unit PF.
文摘This paper proposes and implements a model-free open-loop iterative learning control(ILC)strategy to realize the speed control of the single-phase flux switching motor(FSM)with an asymmetrical rotor.Base on the proposed winding control method,the asymmetrical rotor enables the motor to generate continuous positive torque for positive rotation,and relatively small resistance torque for negative rotation.An initial iteration coefficient and variable iteration coefficient optimized scheme was proposed based on the characteristics of the hardware circuit,thereby forming the model-free strategy.A series of prototype experiments was carried out.Experimental results verify the effectiveness and practicability of the proposed ILC strategy.
基金supported in part by the Natural Science Foundation of Shaanxi Province under Grant 2023JCQN0534in part by the Natural Science Foundation of Shaanxi Provincial Department of Education under Grant 23JK0660in part by the Xi’an Municipal Bureau of Science and Technology under Grant 24GXF0085。
文摘The information of the field current is essential for the brushless synchronous starter/generator system,which determines the performance and health status of this system.However,since the field winding of the main machine is installed in the rotor part,the measurement of the field current in this brushless system seem impossible.Considering that,the field current might be affected by the rectifier mode,the field current estimation method in different rectifier mode is studied in this paper.The main exciter(ME)rotor currents were restructured based on the ME flux equations.With these restructured rotor currents,the field current in different rectifier commutation mode is analyzed,then the field current estimation method considering the rectifier mode can be obtained.The experiments in different rectifier modes are carried out to verify the proposed method.
文摘The face velocities of the high efficiency particulate air filters and the ultra low penetration airfilters in fan filter units (FFUs) have large relative standard deviation and turbulivity. It seriously affects the unidirectivity of the flow in the unidirectional flow clean zone and cleanroom. The cross contamination in this kind of unidirectional flow area is hardly controlled. It is significant to find optional method for keeping the face velocity uniformity of FFU and reducing the face velocity turbulivity of FFU, furthermore, to keep the cleanliness level under FFUs. The normal and easy method is to add flow rectifiers under filters. FFUs with various flow rectifiers have been tested. The uniformity and turbulivity of facevelocity under the FFU are presented in this paper. The influence of the facevelocity uniformity and turbulivity on the contamination boundary of the unidirectional flow is studiedas well.
文摘On the basis of detailed analysis of a novel harmonic counteracting method which can be used to effectively compensate the supply line harmonic currents of a passive single phase diode bridge rectifier, this paper presents two simpler single phase diode bridge rectifier configurations and their alternatives which can achieve low supply line current THD(total harmonic distortion) too. Moreover, this paper also proposes a few passive hamonic counteracting networks for multi single phase rectifiers which are connected in parallel.
基金supported by the National Key Research and Development Plan(2017YFB0404300,2017YFB0404301)
文摘A novel white-light emitting single-phase phosphor La_3 Si_6 N_(11):Dy^(3+),exhibiting two emission peaks centering at 475 and 575 nm, was prepared via conventional solid-state reactions. The structure and morphology of La_3 Si_6 N_(11):Dy^(3+)/Tb^(3+) were investigated by X-ray diffraction(XRD) and scanning electron microscopy(SEM). The emission colors can be tuned from white to yellow-green through increasing the Tb^(3+) concentration in La_3 Si_6 N_(11):Dy^(3+),Tb^(3+), The mechanism of energy transfer(ET) from Dy^(3+) to Tb^(3+) is confirmed according to the excitation,emission spectra and decay lifetimes curve. The temperaturedependent luminescence measurements of La_(2.83)Si_6 N_(11):0.1 Dy^(3+),0.07 Tb^(3+) were also performed, and a good thermal stability is shown, suggesting superior properties for the application as white lightemitting diodes(w-LEDs) phosphor.
基金supported by State Grid Science and Technology Project“Study on Key Technologies of Large Scale Offshore Wind Power Integrating with Onshore Grid”(4000-202055045A-0-0-00)
文摘Due to low investment cost and high reliability,a new scheme called DR-HVDC(Diode Rectifier based HVDC)transmission was recently proposed for grid integration of large offshore wind farms.However,in this scheme,the application of conventional control strategies for stability operation face several challenges due to the uncontrollability of the DR.In this paper,a coordinated control strategy of offshore wind farms using the DR-HVDC transmission technology to connect with the onshore grid,is investigated.A novel coordinated control strategy for DR-HVDC is proposed based on the analysis of the DC current control ability of the full-bridge-based modular multilevel converter(FB-MMC)at the onshore station and the input and output characteristics of the diode rectifier at the offshore.Considering the characteristics of operation stability and decoupling between reactive power and active power,a simplified design based on double-loop droop control for offshore AC voltage is proposed after power flow and voltage–current(I–V)characteristics of the offshore wind farm being analyzed.Furthermore,the impact of onshore AC fault to offshore wind farm is analyzed,and a fast fault detection and protection strategy without relying on communication is proposed.Case studies carried out by PSCAD/EMTDC verify the effectiveness of the proposed control strategy for the start up,power fluctuation,and onshore and offshore fault conditions.
文摘The Auto-Transformer Rectifier Unit（ATRU） is one preferred solution for high-power AC/DC power conversion in aircraft. This is mainly due to its simple structure, high reliability and reduced k VA ratings. Indeed, the ATRU has become a preferred AC/DC solution to supply power to the electric environment control system on-board future aircraft. In this paper, a general modelling method for ATRUs is introduced. The developed model is based on the fact that the DC voltage and current are strongly related to the voltage and current vectors at the AC terminals of ATRUs. In this paper, we carry on our research in modelling symmetric 18-pulse ATRUs and develop a generic modelling technique. The developed generic model can study not only symmetric but also asymmetric ATRUs. An 18-pulse asymmetric ATRU is used to demonstrate the accuracy and efficiency of the developed model by comparing with corresponding detailed switching SABER models provided by our industrial partner. The functional models also allow accelerated and accurate simulations and thus enable whole-scale more-electric aircraft electrical power system studies in the future.
基金This project was supported by the National Natural Science Foundation of China(No.51174025)Specialized Research Fund for the Doctoral Program of Higher Education of China(No.20110006130004).
文摘The microstructure,mechanical property,and in vitro biocorrosion behavior of as-cast single-phase biodegradable Mg-1.5Zn-0.6Zr alloy were investigated and compared with a commercial as-cast AZ91D alloy.The results show that the Mg-1.5Zn-0.6Zr alloy had a single-phase solid solution structure,with an average grain size of 34.7±13.1μm.The alloy exhibited ultimate tensile strength of 168±2.0 MPa,yield strength of 83±0.6 MPa,and elongation of 9.1±0.6%.Immersion tests and electrochemical measurements reveal that the alloy displayed lower biocorrosion rate and more uniform corrosion mode than AZ91D in Hank's solution.The elimination of intensive galvanic corrosion reactions and the formation of a much more compact and uniform corrosion film mainly account for the better biocorrosion properties of the Mg-1.5Zn-0.6Zr alloy than AZ91D.
基金Project supported by the State Key Program of the National Natural Science Foundation of China(Grant No.61234006)
文摘This paper describes the successful fabrication of 4H-SiC junction barrier Schottky （JBS） rectifiers with a linearly graded field limiting ring （LG-FLR）. Linearly variable ring spacings for the FLR termination are applied to improve the blocking voltage by reducing the peak surface electric field at the edge termination region, which acts like a variable lateral doping profile resulting in a gradual field distribution. The experimental results demonstrate a breakdown voltage of 5 kV at the reverse leakage current density of 2 mA/cm2 （about 80% of the theoretical value）. Detailed numerical simulations show that the proposed termination structure provides a uniform electric field profile compared to the conventional FLR termi- nation, which is responsible for 45% improvement in the reverse blocking voltage despite a 3.7% longer total termination length.
文摘The principle of single to single phase matrix electric power conversioin is further studied and the conversioin switch function is introduced into conventional rectifier inverter, thus a general character of the two conversion techniques is discovered. It is characteristic of the switch functiion to follow mains voltage distortion and mains frequency drift. By utilizing the merit, unidirectional switch duty rations of the inverter follow the variation of DC link voltage automatically, thus the size of DC link electrolytic capacitor can be reduced considerably, bringing about improved mains side power factor. Corresponding topologies and theoretical and theoretical derivations are given, and so are the simulation results, based on which it is confirmed that the single to single phase matrix conversion technique is potentially useful in large scale production, and the introduction of switch function can yield good economic returns.
文摘This study focuses on the effects of rotational and welding speeds on the microstructure and hardness of joints in friction stir welded single-phase brass. Welds were achieved under low heat input conditions at rotational and welding speeds of 400-800 r/min and 100-300 mm/min, respectively. In order to characterize the obtained welds, optical microscopy and Vickers hardness measurements were taken on the weld cross sections. According to the obtained results, increasing the welding speed and/or decreasing the rotational speed caused the grain size of the stir zone to decrease and, hence, improved the average hardness of this region. These results are discussed with respect to the interplay between the welding parameters and the peak temperature in the weld thermal cycle.
基金Project supported by the International Research Training Group "Materials and Concepts for Interconnects and Nanosystems"
文摘An improved structure of Schottky rectifier, called a trapezoid mesa trench metal oxide semiconductor （MOS） barrier Schottky rectifier （TM-TMBS）, is proposed and studied by two-dimensional numerical simulations. Both forward and especially better reverse I-V characteristics, including lower leakage current and higher breakdown voltage, are demonstrated by comparing our proposed TM-TMBS with a regular trench MOS barrier Schottky rectifier （TMBS） as well as a conventional planar Schottky barrier diode rectifier. Optimized device parameters corresponding to the requirement for high breakdown voltage are given. With optimized parameters, TM-TMBS attains a breakdown voltage of 186 V, which is 6.3% larger than that of the optimized TMBS, and a leakage current of 4.3×10^-6 A/cm2, which is 26% smaller than that of the optimized TMBS. The relationship between optimized breakdown voltage and some device parameters is studied. Explanations and design rules are given according to this relationship.
基金supported in part by the National Natural Science Foundation of China (Nos. 51777093 ,51722702)
文摘The Vienna rectifier with unbalanced input voltage and load transient is analyzed.A nonlinear control strategy for Vienna rectifier under unbalanced input is proposed.From the view of positive and negative sequence components,the proposed nonlinear control strategy suppresses the twice frequency ripple and guarantees the dynamic response characteristic at the same time.Thanks to the proposed nonlinear control strategy,the DC bus capacitor can be reduced a lot since the voltage ripple and drop can be suppressed.A 10 kW Vienna rectifier is built to verify the proposed control strategy.After applying the proposed nonlinear control strategy,the voltage ripple is only7 V and decreases over 75%over the traditional PI control when the unbalanced degree is 20%.The voltage drop can be reduced about 80%than former control strategy which is helpful to reduce the DC bus capacitor and achieve higher power density.The volume of the capacitor can be reduced by 83.3%with the new control method.
基金supported by the State Key Program of the National Natural Science Foundation of China(Grant No.61234006)the Open Foundation of the State Key Laboratory of Electronic Thin Films and Integrated Devices,China(Grant No.KFJJ201301)the National Science and Technology Major Project of the Ministry of Science and Technology,China(Grant No.2013ZX02305-003)
文摘The effect of the mesa configuration on the reverse breakdown characteristic of a SiC PiN rectifier for high-voltage applications is analyzed in this study.Three geometrical parameters,i.e.,mesa height,mesa angle and mesa bottom corner,are investigated by numerical simulation.The simulation results show that a deep mesa height,a small mesa angle and a smooth mesa bottom（without sub-trench） could contribute to a high breakdown voltage due to a smooth and uniform surface electric field distribution.Moreover,an optimized mesa structure without sub-trench（mesa height of 2.2 μm and mesa angle of 20°） is experimentally demonstrated.A maximum reverse blocking voltage of 4 kV and a forward voltage drop of 3.7 V at 100 A/cm^2 are obtained from the fabricated diode with a 30-μm thick N^- epi-layer,corresponding to 85% of the ideal parallel-plane value.The blocking characteristic as a function of the JTE dose is also discussed for the PiN rectifiers with and without interface charge.
文摘The aim of this study was to compare the effects of d, l-Sotalol and dSotalol on the delayed rectifier K+ outward current in the presence of isoproterenol at different concentrations. Time-dependent delayed rectifier K+ outward currents were measured in isolated guinea pig single myocytes using the whole-cell configuration of the patch-clamp technique. Currents were measured in response to 300 ms depolarizing pulses from a holding potential of -40 mV in three experimental protocols [control, isoproterenol (10^(9)mol/L - 10^(-6) mol/L ), and isoproterenol (10^(-9)mol/L - 10^(-6)mol/L ) plus either d, l-Sotalol (10^(-4) mol/L) or d-Sotalol (10^(-4) mol/L)]. IK tail currents were measured upon repolarization to -40 mV. It was found that Ik was significantly amplified in the presence. of isoproterenol (10^(-9) mol/L- 10^(-6) mol/L) plus d-Sotalol. At 10-8 mol/L isoproterenol, Ik was increased by 92. 7%±17. 1 % (P<0. 05) and 54. 3 %±13. 4 % after d-Sotalol addition (P<0. 05). In contrast, d, l-Sotalol completely conteracted the increase of iK by isoproterenol (<10^(-8) mol/L), and compared to control, Ic was decreased by 35. 6 % ±8. 1% at 10^(-8) mol/L isoproterenol plus d, l-Sotalol (P<0. 05). It is concluded that the β-adrenergic blocking property of d, l-Sotalol but not that of dSotalol maintains the delayed rectifier K+ outward current blockade in the presence of isoproterenol in guinea pig myocytes. This might contribute to a superior antiarrhythmic efficacy as compared to d-Sotalol.
