Wire arc additive manufacturing(WAAM)has emerged as a promising approach for fabricating large-scale components.However,conventional WAAM still faces challenges in optimizing microstructural evolution,minimizing addit...Wire arc additive manufacturing(WAAM)has emerged as a promising approach for fabricating large-scale components.However,conventional WAAM still faces challenges in optimizing microstructural evolution,minimizing additive-induced defects,and alleviating residual stress and deformation,all of which are critical for enhancing the mechanical performance of the manufactured parts.Integrating interlayer friction stir processing(FSP)into WAAM significantly enhances the quality of deposited materials.However,numerical simulation research focusing on elucidating the associated thermomechanical coupling mechanisms remains insufficient.A comprehensive numerical model was developed to simulate the thermomechanical coupling behavior in friction stir-assisted WAAM.The influence of post-deposition FSP on the coupled thermomechanical response of the WAAM process was analyzed quantitatively.Moreover,the residual stress distribution and deformation behavior under both single-layer and multilayer deposition conditions were investigated.Thermal analysis of different deposition layers in WAAM and friction stir-assisted WAAM was conducted.Results show that subsequent layer deposition induces partial remelting of the previously solidified layer,whereas FSP does not cause such remelting.Furthermore,thermal stress and deformation analysis confirm that interlayer FSP effectively mitigates residual stresses and distortion in WAAM components,thereby improving their structural integrity and mechanical properties.展开更多
In recent years,three-dimensional reconstruction technologies that employ multiple cameras have continued to evolve significantly,enabling remote collaboration among users in extended Reality(XR)environments.In additi...In recent years,three-dimensional reconstruction technologies that employ multiple cameras have continued to evolve significantly,enabling remote collaboration among users in extended Reality(XR)environments.In addition,methods for deploying multiple cameras for motion capture of users(e.g.,performers)are widely used in computer graphics.As the need to minimize and optimize the number of cameras grows to reduce costs,various technologies and research approaches focused on Optimal Camera Placement(OCP)are continually being proposed.However,as most existing studies assume homogeneous camera setups,there is a growing demand for studies on heterogeneous camera setups.For instance,technical demands keep emerging in scenarios with minimal camera configurations,especially regarding cost factors,the physical placement of cameras given the spatial structure,and image capture strategies for heterogeneous cameras,such as high-resolution RGB cameras and depth cameras.In this study,we propose a pre-visualization and simulation method for the optimal placement of heterogeneous cameras in XR environments,accounting for both the specifications of heterogeneous cameras(e.g.,field of view)and the physical configuration(e.g.,wall configuration)in real-world spaces.The proposed method performs a visibility analysis of cameras by considering each camera’s field-of-view volume,resolution,and unique characteristics,along with physicalspace constraints.This approach enables the optimal position and rotation of each camera to be recommended,along with the minimum number of cameras required.In the results of our study conducted in heterogeneous camera combinations,the proposed method achieved 81.7%~82.7%coverage of the target visual information using only 2~3 cameras.In contrast,single(or homogeneous)-typed cameras were required to use 11 cameras for 81.6%coverage.Accordingly,we found that camera deployment resources can be reduced with the proposed approaches.展开更多
Because of the developed surface of the Triply PeriodicMinimumSurface(TPMS)structures,polylactide(PLA)products with a TPMS structure are thought to be promising bio soluble implants with the potential for targeted dru...Because of the developed surface of the Triply PeriodicMinimumSurface(TPMS)structures,polylactide(PLA)products with a TPMS structure are thought to be promising bio soluble implants with the potential for targeted drug delivery.For implants,mechanical properties are key performance characteristics,so understanding the deformation and failure mechanisms is essential for selecting the appropriate implant structure.The deformation and fracture processes in PLA samples with different interior architectures have been studied through computer simulation and experimental research.Two TPMS topologies,the Schwarz Diamond and Gyroid architectures,were used for the sample construction by 3D printing.ANSYS software was utilized to simulate compressive deformation.It was found that under the same load,the vonMises stresses in the Gyroid structure are higher than those in the Schwartz Diamond structure,which was associated with the different orientations of the cells in the studied structures in relation to the direction of the loading axis.The deformation process occurs in the local regions of the studied TPMS structures.Maximum von Mises stresses were observed in the vertical parts of the structures oriented along the load direction.It was found that,unlike the Gyroid,the Schwartz Diamond structure contains a frame that forms unique stiffening ribs,which ensures the redistribution of the load under the vertical loading direction.An analysis of the mechanical characteristics of PLA samples with the Schwartz Diamond and Gyroid structures produced by the Fused Deposition Modeling(FDM)method was correlated with computer simulation.The Schwarz Diamond-type structure was shown to have a higher absorption energy than the Gyroid one.A study of the fracture in PLA samples with various cell sizes revealed a particular feature related to the samples’periodic surface topology and the 3D printing process.Scanning electron microscopic(SEM)studies of the samples deformed by compression showed thatwith an increase in the density of the samples,the failure mechanism changes from ductile to quasi-brittle due to the complex participation of both cell deformation and fiber deformation.展开更多
In federated learning,backdoor attacks have become an important research topic with their wide application in processing sensitive datasets.Since federated learning detects or modifies local models through defense mec...In federated learning,backdoor attacks have become an important research topic with their wide application in processing sensitive datasets.Since federated learning detects or modifies local models through defense mechanisms during aggregation,it is difficult to conduct effective backdoor attacks.In addition,existing backdoor attack methods are faced with challenges,such as low backdoor accuracy,poor ability to evade anomaly detection,and unstable model training.To address these challenges,a method called adaptive simulation backdoor attack(ASBA)is proposed.Specifically,ASBA improves the stability of model training by manipulating the local training process and using an adaptive mechanism,the ability of the malicious model to evade anomaly detection by combing large simulation training and clipping,and the backdoor accuracy by introducing a stimulus model to amplify the impact of the backdoor in the global model.Extensive comparative experiments under five advanced defense scenarios show that ASBA can effectively evade anomaly detection and achieve high backdoor accuracy in the global model.Furthermore,it exhibits excellent stability and effectiveness after multiple rounds of attacks,outperforming state-of-the-art backdoor attack methods.展开更多
BACKGROUND Orthopaedic surgical education has traditionally depended on the apprenticeship model of“see one,do one,teach one”.However,reduced operative exposure,stricter work-hour regulations,medicolegal constraints...BACKGROUND Orthopaedic surgical education has traditionally depended on the apprenticeship model of“see one,do one,teach one”.However,reduced operative exposure,stricter work-hour regulations,medicolegal constraints,and patient safety concerns have constrained its practicality.Simulation-based training has become a reliable,safe,and cost-efficient alternative.Dry lab techniques,especially virtual and augmented reality,make up 78%of current dry lab research,whereas wet labs still set the standard for anatomical realism.AIM To evaluate the effectiveness,limitations,and future directions of wet and dry lab simulation in orthopaedic training.METHODS A scoping review was carried out across four databases-PubMed,Cochrane Library,Web of Science,and EBSCOhost-up to 2025.Medical Subject Headings included:"Orthopaedic Education","Wet Lab","Dry Lab","Simulation Training","Virtual Reality",and"Surgical Procedure".Eligible studies focused on orthopaedic or spinal surgical education,employed wet or dry lab techniques,and assessed training effectiveness.Exclusion criteria consisted of non-English publications,abstracts only,non-orthopaedic research,and studies unrelated to simulation.Two reviewers independently screened titles,abstracts,and full texts,resolving discrepancies with a third reviewer.RESULTS From 1851 records,101 studies met inclusion:78 on dry labs,7 on wet labs,4 on both.Virtual reality(VR)simulations were most common,with AI increasingly used for feedback and assessment.Cadaveric training remains the gold standard for accuracy and tactile feedback,while dry labs-especially VR-offer scalability,lower cost(40%-60%savings in five studies),and accessibility for novices.Senior residents prefer wet labs for complex tasks;juniors favour dry labs for basics.Challenges include limited transferability data,lack of standard outcome metrics,and ethical concerns about cadaver use and AI assessment.CONCLUSION Wet and dry labs each have unique strengths in orthopaedic training.A hybrid approach combining both,supported by standardised assessments and outcome studies,is most effective.Future efforts should aim for uniform reporting,integrating new technologies,and policy support for hybrid curricula to enhance skills and patient care.展开更多
Regenerative catalytic oxidizers(RCO)are widely used to remove volatile organic compounds(VOCs)due to their energy-saving and stability.In this study,a multi-component catalytic reaction model was constructed to numer...Regenerative catalytic oxidizers(RCO)are widely used to remove volatile organic compounds(VOCs)due to their energy-saving and stability.In this study,a multi-component catalytic reaction model was constructed to numerically investigate the reaction process of hydrocarbon-containing VOCs in RCO using computational fluid dynamics(CFD)simulation.To obtain the conversion characteristics of multi-component hydrocarbons,the effects of intake load,equivalence ratio,and the composition of multi-component hydrocarbons on the flow,heat transfer,and conversion rate of the reactor were analyzed.A feasibility study plan targeting the hard-to-convert components was also proposed.The results indicated that as the load increases,the conversion rates of the various components decrease,while the reaction rates increase.Moreover,increasing the flow velocity intensifies turbulence and enhances the collision frequency between the gas and the wall surfaces.This,in turn,amplifies the resistance effect of the porous medium.As the equivalence ratio of VOCs to oxygen increases,the oxygen-deficient condition leads to a decrease in the molecular weight of the hydrocarbons involved in the reaction.The reaction temperature also shows a downward trend.A comparative analysis of the catalytic combustion characteristics of multi-component VOCs and single-component gases reveals that adding ethane and propane can facilitate methane oxidation.展开更多
Ice crystal icing is an important cause of accidents in aircraft engines.Ice formation in aircraft engines can cause internal blades to freeze,affecting the quality of the air flow field and blocking the flow path.On ...Ice crystal icing is an important cause of accidents in aircraft engines.Ice formation in aircraft engines can cause internal blades to freeze,affecting the quality of the air flow field and blocking the flow path.On the other hand,the entry of ice crystal particles into the combustion chamber can cause a decrease in temperature or even flameout,leading to engine surge or shutdown.Therefore,it is necessary to conduct multiphase flow tests on ice crystals for aircraft components such as aircraft engines.Conducting ice crystal multiphase flow tests on aircraft is an effective research method,but it requires the construction of an ice crystal multiphase flow test platform that meets relevant technical requirements.The paper focuses on the relevant experimental requirements and combines wind tunnel test structures to conduct multiphase flow numerical simulations on various forms of jet pipelines,obtaining particle motion distribution results.After comparison,the optimal form of jet structure is obtained,providing the best selection scheme for the design of relevant wind tunnel structures.展开更多
Centrifugal casting of ductile iron pipe is a high-temperature,semi-continuous production process.However,conducting laboratory research on the solidification process of centrifugal casting of ductile iron pipe presen...Centrifugal casting of ductile iron pipe is a high-temperature,semi-continuous production process.However,conducting laboratory research on the solidification process of centrifugal casting of ductile iron pipe presents significant challenges.In this study,a novel research method was introduced for investigating the solidification process of ductile iron pipe,namely thermal simulation of ductile iron pipe.Comparative research was conducted on the microstructure and properties of the thermal simulation sample and the ductile iron pipe.The findings indicate that the thermal simulation sample and ductile iron pipe exhibit good heat transfer similarity and microstructure similarity.The difference of cooling rate between thermal simulation sample and ductile pipe is less than 0.24℃·s^(-1),and the difference of microstructure content of free cementite,ferrite,and pearlite is less than 5%.The tensile strength of annealed ductile iron pipe is 466 MPa,with an elongation of 16.1%and a Brinell hardness of 156.5 HBW.In comparison,the tensile strength of annealed thermal simulation sample is 482.0 MPa,with an elongation of 15.5%and a Brinell hardness of 159.0 HBW.These results suggest that the thermal simulation experimental research method is both scientific and feasible,offering an objective,reliable,and cost-effective approach to laboratory research on ductile iron pipe.展开更多
Injecting impure CO_(2)for enhanced gas recovery(CO_(2)-EGR)offers a dual benefit by improving natural gas extraction while enabling CO_(2)sequestration.However,the interactions between CO_(2),N_(2),and CH_(4)under re...Injecting impure CO_(2)for enhanced gas recovery(CO_(2)-EGR)offers a dual benefit by improving natural gas extraction while enabling CO_(2)sequestration.However,the interactions between CO_(2),N_(2),and CH_(4)under reservoir conditions require further investigation.This study employs Grand Canonical Monte Carlo(GCMC)and Molecular Dynamics(MD)simulations to quantify the adsorption and diffusion behaviors of CO_(2),N_(2),and CH_(4)in quartz nanopores over a pressure range of 1-24 MPa under varying water saturations and gas compositions.The results indicate that:(1)CO_(2)exhibits the broadest energy distribution and the strongest adsorption stability,occupying about 20%-30%more adsorption sites than CH_(4)or N_(2)and showing the least sensitivity to water saturation,with only a 30%reduction at 50%saturation,compared to 60%for CH_(4),giving CO_(2)a clear competitive advantage.(2)The adsorption and desorption behaviors are strongly pressure dependent,as increasing pressure reduces the adsorption layer area and shifts gas distribution from adsorption dominated to free phase.Competitive adsorption analysis reveals that while CO_(2)dominates displacement at low pressures,mixtures that contain N_(2)achieve higher CH_(4)desorption efficiency above 13 MPa by mitigating diffusion resistance.(3)A higher N_(2)fraction improves CH_(4)diffusion coefficients,thereby facilitating gas mobility and ensuring superior recovery performance under high-pressure conditions.This study advances the fundamental knowledge of microscale gas behavior in tight sandstones and supports the feasibility of impure CO_(2)injection as a practical strategy for sustainable gas production.展开更多
The F_(1)-ATPase and V_(1)-ATPase are rotary biomotors.Alignment of their amino acid sequences,which originate from bovine heart mitochondria(1BMF)and Enterococcus hirae(3VR6),respectively,demonstrates that the segmen...The F_(1)-ATPase and V_(1)-ATPase are rotary biomotors.Alignment of their amino acid sequences,which originate from bovine heart mitochondria(1BMF)and Enterococcus hirae(3VR6),respectively,demonstrates that the segment forming the ATP catalytic pocket is highly conserved.Single-molecule experiments,however,have revealed subtle differences in efficiency between the F_(1) and V_(1) motors.Here,we perform both atomistic and coarse-grained molecular dynamics simulations to investigate the mechanochemical coupling and coordination in F_(1) and V_(1) ATPase.Our results show that the correlation between conformational changes in F_(1) is stronger than that in V_(1),indicating that the mechanochemical coupling in F_(1) is tighter than in V_(1).Moreover,the unidirectional rotation of F_(1) is more processive than that of V_(1),which accounts for the higher efficiency observed in F_(1) and explains the occasional backward steps detected in single-molecule experiments on V_(1).展开更多
Objectives This study aimed to compare the effectiveness of the semi-virtual simulation and traditional simulation teaching models based on the Standards of Best Practice(SOBP)according to the International Nursing As...Objectives This study aimed to compare the effectiveness of the semi-virtual simulation and traditional simulation teaching models based on the Standards of Best Practice(SOBP)according to the International Nursing Association for Clinical Simulation and Learning(INACSL)in the Adult Nursing course.Methods This study used a quasi-experimental design.A total of 94 third-year nursing students from a university in Beijing between November and December 2022 were recruited as participants.An innovative semi-virtual simulation teaching model was designed based on the SOBP established by the INACSL.In the Adult Nursing course,both the semi-virtual and traditional simulation teaching models were implemented.At the end of the simulation sessions,participants completed the Chinese version of the Simulation Effectiveness Tool-Modified(SET-M)to assess the effectiveness of the two teaching models.Results All nursing students completed the simulation sessions.There was no difference(t=−0.93,P=0.353)in the total scores between the semi-virtual simulation teaching model(50.87±5.30)and the traditional simulation teaching model(50.37±5.16).However,there was a statistically significant difference(t=−2.65,P=0.010)in the prebriefing section(semi-virtual simulation:5.60±0.71;traditional simulation:5.33±0.78).In contrast,no statistically significant differences were found for the scenario and debriefing sections(P>0.05).At the individual item level,statistical differences(P<0.05)between the two models were identified for items 1 and 9,but not for the remaining items(P>0.05).By analyzing the open-ended question,it was found that both simulation models were effective,and students’comments were similar.Conclusions The study demonstrated equivalent effectiveness between the semi-virtual and traditional simulation teaching models.Semi-virtual simulation teaching model could offer a more flexible and feasible approach to simulation teaching.展开更多
This study introduces a new ocean surface friction velocity scheme and a modified Thompson cloud microphysics parameterization scheme into the CMA-TYM model.The impact of these two parameterization schemes on the pred...This study introduces a new ocean surface friction velocity scheme and a modified Thompson cloud microphysics parameterization scheme into the CMA-TYM model.The impact of these two parameterization schemes on the prediction of the movement track and intensity of Typhoon Kompasu in 2021 is examined.Additionally,the possible reasons for their effects on tropical cyclone(TC)intensity prediction are analyzed.Statistical results show that both parameterization schemes improve the predictions of Typhoon Kompasu’s track and intensity.The influence on track prediction becomes evident after 60 h of model integration,while the significant positive impact on intensity prediction is observed after 66 h.Further analysis reveals that these two schemes affect the timing and magnitude of extreme TC intensity values by influencing the evolution of the TC’s warm-core structure.展开更多
Hydraulic fracturing serves as a critical technology for reservoir stimulation in deep coalbed methane(CBM)development,where the mechanical properties of gangue layers exert a significant control on fracture propagati...Hydraulic fracturing serves as a critical technology for reservoir stimulation in deep coalbed methane(CBM)development,where the mechanical properties of gangue layers exert a significant control on fracture propagation behavior.To address the unclear mechanisms governing fracture penetration across coal-gangue interfaces,this study employs the Continuum-Discontinuum Element Method(CDEM)to simulate and analyze the vertical propagation of hydraulic fractures initiating within coal seams,based on geomechanical parameters derived from the deep Benxi Formation coal seams in the southeastern Ordos Basin.The investigation systematically examines the influence of geological and operational parameters on cross-interfacial fracture growth.Results demonstrate that vertical stress difference,elastic modulus contrast between coal and gangue layers,interfacial stress differential,and interfacial cohesion at coal-gangue interfaces are critical factors governing hydraulic fracture penetration through these interfaces.High vertical stress differences(>3 MPa)inhibit interfacial dilation,promoting predominant crosslayer fracture propagation.Reduced interfacial stress contrasts and enhanced interfacial cohesion facilitate fracture penetration across interfaces.Furthermore,smaller elastic modulus contrasts between coal and gangue correlate with increased interfacial aperture.Finally,lower injection rates effectively suppress vertical fracture propagation in deep coal reservoirs.This study elucidates the characteristics and mechanisms governing cross-layer fracture propagation in coal–rock composites with interbedded partings,and delineates the dynamic evolution laws and dominant controlling factors involved.Thefindings provide critical theoretical insights for the optimization of fracture design and the efficient development of deep coalbed methane reservoirs.展开更多
In sediment transport on a mobile erodible bed,near-bed particles tend to preferentially locate under specific flow regions and form an uneven bedform.These moving and mobile particles can significantly modulate turbu...In sediment transport on a mobile erodible bed,near-bed particles tend to preferentially locate under specific flow regions and form an uneven bedform.These moving and mobile particles can significantly modulate turbulence at various scales,from inertial large-scale motions to small viscous motions.This study analyzes the particle-resolved direct numerical simulation data of particle-laden two-phase flow with multilayers of particles in turbulent flows over static and mobile beds.The double-average method is adopted for energy transfer analysis.The result shows that the alternative streaky bedform in the spanwise directions correlates with the streak structures in the near-wall turbulence in the mobile bed case.The energy redistribution and exchange,as well as the dissipation,are analyzed in detail,and an energy transfer diagram is given in the last to summarize the energy transfer processes.In both the static and mobile bed cases,flow energy is introduced into the system via the work performed by volume forces acting on the mean flow.The viscous dissipations in the double mean and form-induced fields are more pronounced in the static bed case,and the work done by the fluid-particle interfacial stress in the double mean and turbulent fields is more pronounced in the mobile bed case.The prominent energy contribution in the form-induced field is the production by the form-induced stress on the mean strain in the mobile bed case.In addition,sediment transport involving a limited number of mobile particles is insufficient to capture the energy transfer processes that occur over the troughs and may intertwine the energy transfer processes over the mobile particles and the fixed particle bed.展开更多
Automation and intelligence have become the primary trends in the design of investment casting processes.However,the design of gating and riser systems still lacks precise quantitative evaluation criteria.Numerical si...Automation and intelligence have become the primary trends in the design of investment casting processes.However,the design of gating and riser systems still lacks precise quantitative evaluation criteria.Numerical simulation plays a significant role in quantitatively evaluating current processes and making targeted improvements,but its limitations lie in the inability to dynamically reflect the formation outcomes of castings under varying process conditions,making real-time adjustments to gating and riser designs challenging.In this study,an automated design model for gating and riser systems based on integrated parametric 3D modeling-simulation framework is proposed,which enhances the flexibility and usability of evaluating the casting process by simulation.Firstly,geometric feature extraction technology is employed to obtain the geometric information of the target casting.Based on this information,an automated design framework for gating and riser systems is established,incorporating multiple structural parameters for real-time process control.Subsequently,the simulation results for various structural parameters are analyzed,and the influence of these parameters on casting formation is thoroughly investigated.Finally,the optimal design scheme is generated and validated through experimental verification.Simulation analysis and experimental results show that using a larger gate neck(24 mm in side length) and external risers promotes a more uniform temperature distribution and a more stable flow state,effectively eliminating shrinkage cavities and enhancing process yield by 15%.展开更多
Marine thin plates are susceptible to welding deformation owing to their low structural stiffness.Therefore,the efficient and accurate prediction of welding deformation is essential for improving welding quality.The t...Marine thin plates are susceptible to welding deformation owing to their low structural stiffness.Therefore,the efficient and accurate prediction of welding deformation is essential for improving welding quality.The traditional thermal elastic-plastic finite element method(TEP-FEM)can accurately predict welding deformation.However,its efficiency is low because of the complex nonlinear transient computation,making it difficult to meet the needs of rapid engineering evaluation.To address this challenge,this study proposes an efficient prediction method for welding deformation in marine thin plate butt welds.This method is based on the coupled temperature gradient-thermal strain method(TG-TSM)that integrates inherent strain theory with a shell element finite element model.The proposed method first extracts the distribution pattern and characteristic value of welding-induced inherent strain through TEP-FEM analysis.This strain is then converted into the equivalent thermal load applied to the shell element model for rapid computation.The proposed method-particularly,the gradual temperature gradient-thermal strain method(GTG-TSM)-achieved improved computational efficiency and consistent precision.Furthermore,the proposed method required much less computation time than the traditional TEP-FEM.Thus,this study lays the foundation for future prediction of welding deformation in more complex marine thin plates.展开更多
基金National Key Research and Development Program of China(2022YFB4600902)Shandong Provincial Science Foundation for Outstanding Young Scholars(ZR2024YQ020)。
文摘Wire arc additive manufacturing(WAAM)has emerged as a promising approach for fabricating large-scale components.However,conventional WAAM still faces challenges in optimizing microstructural evolution,minimizing additive-induced defects,and alleviating residual stress and deformation,all of which are critical for enhancing the mechanical performance of the manufactured parts.Integrating interlayer friction stir processing(FSP)into WAAM significantly enhances the quality of deposited materials.However,numerical simulation research focusing on elucidating the associated thermomechanical coupling mechanisms remains insufficient.A comprehensive numerical model was developed to simulate the thermomechanical coupling behavior in friction stir-assisted WAAM.The influence of post-deposition FSP on the coupled thermomechanical response of the WAAM process was analyzed quantitatively.Moreover,the residual stress distribution and deformation behavior under both single-layer and multilayer deposition conditions were investigated.Thermal analysis of different deposition layers in WAAM and friction stir-assisted WAAM was conducted.Results show that subsequent layer deposition induces partial remelting of the previously solidified layer,whereas FSP does not cause such remelting.Furthermore,thermal stress and deformation analysis confirm that interlayer FSP effectively mitigates residual stresses and distortion in WAAM components,thereby improving their structural integrity and mechanical properties.
基金supported by the 2024 Research Fund of University of Ulsan.
文摘In recent years,three-dimensional reconstruction technologies that employ multiple cameras have continued to evolve significantly,enabling remote collaboration among users in extended Reality(XR)environments.In addition,methods for deploying multiple cameras for motion capture of users(e.g.,performers)are widely used in computer graphics.As the need to minimize and optimize the number of cameras grows to reduce costs,various technologies and research approaches focused on Optimal Camera Placement(OCP)are continually being proposed.However,as most existing studies assume homogeneous camera setups,there is a growing demand for studies on heterogeneous camera setups.For instance,technical demands keep emerging in scenarios with minimal camera configurations,especially regarding cost factors,the physical placement of cameras given the spatial structure,and image capture strategies for heterogeneous cameras,such as high-resolution RGB cameras and depth cameras.In this study,we propose a pre-visualization and simulation method for the optimal placement of heterogeneous cameras in XR environments,accounting for both the specifications of heterogeneous cameras(e.g.,field of view)and the physical configuration(e.g.,wall configuration)in real-world spaces.The proposed method performs a visibility analysis of cameras by considering each camera’s field-of-view volume,resolution,and unique characteristics,along with physicalspace constraints.This approach enables the optimal position and rotation of each camera to be recommended,along with the minimum number of cameras required.In the results of our study conducted in heterogeneous camera combinations,the proposed method achieved 81.7%~82.7%coverage of the target visual information using only 2~3 cameras.In contrast,single(or homogeneous)-typed cameras were required to use 11 cameras for 81.6%coverage.Accordingly,we found that camera deployment resources can be reduced with the proposed approaches.
文摘Because of the developed surface of the Triply PeriodicMinimumSurface(TPMS)structures,polylactide(PLA)products with a TPMS structure are thought to be promising bio soluble implants with the potential for targeted drug delivery.For implants,mechanical properties are key performance characteristics,so understanding the deformation and failure mechanisms is essential for selecting the appropriate implant structure.The deformation and fracture processes in PLA samples with different interior architectures have been studied through computer simulation and experimental research.Two TPMS topologies,the Schwarz Diamond and Gyroid architectures,were used for the sample construction by 3D printing.ANSYS software was utilized to simulate compressive deformation.It was found that under the same load,the vonMises stresses in the Gyroid structure are higher than those in the Schwartz Diamond structure,which was associated with the different orientations of the cells in the studied structures in relation to the direction of the loading axis.The deformation process occurs in the local regions of the studied TPMS structures.Maximum von Mises stresses were observed in the vertical parts of the structures oriented along the load direction.It was found that,unlike the Gyroid,the Schwartz Diamond structure contains a frame that forms unique stiffening ribs,which ensures the redistribution of the load under the vertical loading direction.An analysis of the mechanical characteristics of PLA samples with the Schwartz Diamond and Gyroid structures produced by the Fused Deposition Modeling(FDM)method was correlated with computer simulation.The Schwarz Diamond-type structure was shown to have a higher absorption energy than the Gyroid one.A study of the fracture in PLA samples with various cell sizes revealed a particular feature related to the samples’periodic surface topology and the 3D printing process.Scanning electron microscopic(SEM)studies of the samples deformed by compression showed thatwith an increase in the density of the samples,the failure mechanism changes from ductile to quasi-brittle due to the complex participation of both cell deformation and fiber deformation.
文摘In federated learning,backdoor attacks have become an important research topic with their wide application in processing sensitive datasets.Since federated learning detects or modifies local models through defense mechanisms during aggregation,it is difficult to conduct effective backdoor attacks.In addition,existing backdoor attack methods are faced with challenges,such as low backdoor accuracy,poor ability to evade anomaly detection,and unstable model training.To address these challenges,a method called adaptive simulation backdoor attack(ASBA)is proposed.Specifically,ASBA improves the stability of model training by manipulating the local training process and using an adaptive mechanism,the ability of the malicious model to evade anomaly detection by combing large simulation training and clipping,and the backdoor accuracy by introducing a stimulus model to amplify the impact of the backdoor in the global model.Extensive comparative experiments under five advanced defense scenarios show that ASBA can effectively evade anomaly detection and achieve high backdoor accuracy in the global model.Furthermore,it exhibits excellent stability and effectiveness after multiple rounds of attacks,outperforming state-of-the-art backdoor attack methods.
文摘BACKGROUND Orthopaedic surgical education has traditionally depended on the apprenticeship model of“see one,do one,teach one”.However,reduced operative exposure,stricter work-hour regulations,medicolegal constraints,and patient safety concerns have constrained its practicality.Simulation-based training has become a reliable,safe,and cost-efficient alternative.Dry lab techniques,especially virtual and augmented reality,make up 78%of current dry lab research,whereas wet labs still set the standard for anatomical realism.AIM To evaluate the effectiveness,limitations,and future directions of wet and dry lab simulation in orthopaedic training.METHODS A scoping review was carried out across four databases-PubMed,Cochrane Library,Web of Science,and EBSCOhost-up to 2025.Medical Subject Headings included:"Orthopaedic Education","Wet Lab","Dry Lab","Simulation Training","Virtual Reality",and"Surgical Procedure".Eligible studies focused on orthopaedic or spinal surgical education,employed wet or dry lab techniques,and assessed training effectiveness.Exclusion criteria consisted of non-English publications,abstracts only,non-orthopaedic research,and studies unrelated to simulation.Two reviewers independently screened titles,abstracts,and full texts,resolving discrepancies with a third reviewer.RESULTS From 1851 records,101 studies met inclusion:78 on dry labs,7 on wet labs,4 on both.Virtual reality(VR)simulations were most common,with AI increasingly used for feedback and assessment.Cadaveric training remains the gold standard for accuracy and tactile feedback,while dry labs-especially VR-offer scalability,lower cost(40%-60%savings in five studies),and accessibility for novices.Senior residents prefer wet labs for complex tasks;juniors favour dry labs for basics.Challenges include limited transferability data,lack of standard outcome metrics,and ethical concerns about cadaver use and AI assessment.CONCLUSION Wet and dry labs each have unique strengths in orthopaedic training.A hybrid approach combining both,supported by standardised assessments and outcome studies,is most effective.Future efforts should aim for uniform reporting,integrating new technologies,and policy support for hybrid curricula to enhance skills and patient care.
基金supported by National Key Research&Development Program of China(2022YFB4101500).
文摘Regenerative catalytic oxidizers(RCO)are widely used to remove volatile organic compounds(VOCs)due to their energy-saving and stability.In this study,a multi-component catalytic reaction model was constructed to numerically investigate the reaction process of hydrocarbon-containing VOCs in RCO using computational fluid dynamics(CFD)simulation.To obtain the conversion characteristics of multi-component hydrocarbons,the effects of intake load,equivalence ratio,and the composition of multi-component hydrocarbons on the flow,heat transfer,and conversion rate of the reactor were analyzed.A feasibility study plan targeting the hard-to-convert components was also proposed.The results indicated that as the load increases,the conversion rates of the various components decrease,while the reaction rates increase.Moreover,increasing the flow velocity intensifies turbulence and enhances the collision frequency between the gas and the wall surfaces.This,in turn,amplifies the resistance effect of the porous medium.As the equivalence ratio of VOCs to oxygen increases,the oxygen-deficient condition leads to a decrease in the molecular weight of the hydrocarbons involved in the reaction.The reaction temperature also shows a downward trend.A comparative analysis of the catalytic combustion characteristics of multi-component VOCs and single-component gases reveals that adding ethane and propane can facilitate methane oxidation.
文摘Ice crystal icing is an important cause of accidents in aircraft engines.Ice formation in aircraft engines can cause internal blades to freeze,affecting the quality of the air flow field and blocking the flow path.On the other hand,the entry of ice crystal particles into the combustion chamber can cause a decrease in temperature or even flameout,leading to engine surge or shutdown.Therefore,it is necessary to conduct multiphase flow tests on ice crystals for aircraft components such as aircraft engines.Conducting ice crystal multiphase flow tests on aircraft is an effective research method,but it requires the construction of an ice crystal multiphase flow test platform that meets relevant technical requirements.The paper focuses on the relevant experimental requirements and combines wind tunnel test structures to conduct multiphase flow numerical simulations on various forms of jet pipelines,obtaining particle motion distribution results.After comparison,the optimal form of jet structure is obtained,providing the best selection scheme for the design of relevant wind tunnel structures.
基金financially supported by the National Natural Science Foundation of China(52130109)。
文摘Centrifugal casting of ductile iron pipe is a high-temperature,semi-continuous production process.However,conducting laboratory research on the solidification process of centrifugal casting of ductile iron pipe presents significant challenges.In this study,a novel research method was introduced for investigating the solidification process of ductile iron pipe,namely thermal simulation of ductile iron pipe.Comparative research was conducted on the microstructure and properties of the thermal simulation sample and the ductile iron pipe.The findings indicate that the thermal simulation sample and ductile iron pipe exhibit good heat transfer similarity and microstructure similarity.The difference of cooling rate between thermal simulation sample and ductile pipe is less than 0.24℃·s^(-1),and the difference of microstructure content of free cementite,ferrite,and pearlite is less than 5%.The tensile strength of annealed ductile iron pipe is 466 MPa,with an elongation of 16.1%and a Brinell hardness of 156.5 HBW.In comparison,the tensile strength of annealed thermal simulation sample is 482.0 MPa,with an elongation of 15.5%and a Brinell hardness of 159.0 HBW.These results suggest that the thermal simulation experimental research method is both scientific and feasible,offering an objective,reliable,and cost-effective approach to laboratory research on ductile iron pipe.
基金supported by the National Natural Science Foundation of China(Grant No.U23A2022)the National Natural Science Foundation of China(Grant No.52474047)+2 种基金the Natural Science Foundation of Chongqing(Grant No.CSTB2024NSCQ-MSX0951)the Natural Science Foundation of Sichuan Province(Grant No.2025ZNSFSC1357)the National Science and Technology Major Project(Grant No.2025ZD1404307).
文摘Injecting impure CO_(2)for enhanced gas recovery(CO_(2)-EGR)offers a dual benefit by improving natural gas extraction while enabling CO_(2)sequestration.However,the interactions between CO_(2),N_(2),and CH_(4)under reservoir conditions require further investigation.This study employs Grand Canonical Monte Carlo(GCMC)and Molecular Dynamics(MD)simulations to quantify the adsorption and diffusion behaviors of CO_(2),N_(2),and CH_(4)in quartz nanopores over a pressure range of 1-24 MPa under varying water saturations and gas compositions.The results indicate that:(1)CO_(2)exhibits the broadest energy distribution and the strongest adsorption stability,occupying about 20%-30%more adsorption sites than CH_(4)or N_(2)and showing the least sensitivity to water saturation,with only a 30%reduction at 50%saturation,compared to 60%for CH_(4),giving CO_(2)a clear competitive advantage.(2)The adsorption and desorption behaviors are strongly pressure dependent,as increasing pressure reduces the adsorption layer area and shifts gas distribution from adsorption dominated to free phase.Competitive adsorption analysis reveals that while CO_(2)dominates displacement at low pressures,mixtures that contain N_(2)achieve higher CH_(4)desorption efficiency above 13 MPa by mitigating diffusion resistance.(3)A higher N_(2)fraction improves CH_(4)diffusion coefficients,thereby facilitating gas mobility and ensuring superior recovery performance under high-pressure conditions.This study advances the fundamental knowledge of microscale gas behavior in tight sandstones and supports the feasibility of impure CO_(2)injection as a practical strategy for sustainable gas production.
基金supported by the National Natural Science Foundation of China(Grant Nos.22193032 and 32401033)the Research Fund of Wenzhou Institute,Chinese Academy of Sciences(Grant Nos.WIUCASQD2020009,WIUCASQD2023005,XSZD2024004,2021HZSY0061,and WIUCASICTP2022)。
文摘The F_(1)-ATPase and V_(1)-ATPase are rotary biomotors.Alignment of their amino acid sequences,which originate from bovine heart mitochondria(1BMF)and Enterococcus hirae(3VR6),respectively,demonstrates that the segment forming the ATP catalytic pocket is highly conserved.Single-molecule experiments,however,have revealed subtle differences in efficiency between the F_(1) and V_(1) motors.Here,we perform both atomistic and coarse-grained molecular dynamics simulations to investigate the mechanochemical coupling and coordination in F_(1) and V_(1) ATPase.Our results show that the correlation between conformational changes in F_(1) is stronger than that in V_(1),indicating that the mechanochemical coupling in F_(1) is tighter than in V_(1).Moreover,the unidirectional rotation of F_(1) is more processive than that of V_(1),which accounts for the higher efficiency observed in F_(1) and explains the occasional backward steps detected in single-molecule experiments on V_(1).
文摘Objectives This study aimed to compare the effectiveness of the semi-virtual simulation and traditional simulation teaching models based on the Standards of Best Practice(SOBP)according to the International Nursing Association for Clinical Simulation and Learning(INACSL)in the Adult Nursing course.Methods This study used a quasi-experimental design.A total of 94 third-year nursing students from a university in Beijing between November and December 2022 were recruited as participants.An innovative semi-virtual simulation teaching model was designed based on the SOBP established by the INACSL.In the Adult Nursing course,both the semi-virtual and traditional simulation teaching models were implemented.At the end of the simulation sessions,participants completed the Chinese version of the Simulation Effectiveness Tool-Modified(SET-M)to assess the effectiveness of the two teaching models.Results All nursing students completed the simulation sessions.There was no difference(t=−0.93,P=0.353)in the total scores between the semi-virtual simulation teaching model(50.87±5.30)and the traditional simulation teaching model(50.37±5.16).However,there was a statistically significant difference(t=−2.65,P=0.010)in the prebriefing section(semi-virtual simulation:5.60±0.71;traditional simulation:5.33±0.78).In contrast,no statistically significant differences were found for the scenario and debriefing sections(P>0.05).At the individual item level,statistical differences(P<0.05)between the two models were identified for items 1 and 9,but not for the remaining items(P>0.05).By analyzing the open-ended question,it was found that both simulation models were effective,and students’comments were similar.Conclusions The study demonstrated equivalent effectiveness between the semi-virtual and traditional simulation teaching models.Semi-virtual simulation teaching model could offer a more flexible and feasible approach to simulation teaching.
基金supported by the National Key R&D Program of China[grant number 2023YFC3008004]。
文摘This study introduces a new ocean surface friction velocity scheme and a modified Thompson cloud microphysics parameterization scheme into the CMA-TYM model.The impact of these two parameterization schemes on the prediction of the movement track and intensity of Typhoon Kompasu in 2021 is examined.Additionally,the possible reasons for their effects on tropical cyclone(TC)intensity prediction are analyzed.Statistical results show that both parameterization schemes improve the predictions of Typhoon Kompasu’s track and intensity.The influence on track prediction becomes evident after 60 h of model integration,while the significant positive impact on intensity prediction is observed after 66 h.Further analysis reveals that these two schemes affect the timing and magnitude of extreme TC intensity values by influencing the evolution of the TC’s warm-core structure.
文摘Hydraulic fracturing serves as a critical technology for reservoir stimulation in deep coalbed methane(CBM)development,where the mechanical properties of gangue layers exert a significant control on fracture propagation behavior.To address the unclear mechanisms governing fracture penetration across coal-gangue interfaces,this study employs the Continuum-Discontinuum Element Method(CDEM)to simulate and analyze the vertical propagation of hydraulic fractures initiating within coal seams,based on geomechanical parameters derived from the deep Benxi Formation coal seams in the southeastern Ordos Basin.The investigation systematically examines the influence of geological and operational parameters on cross-interfacial fracture growth.Results demonstrate that vertical stress difference,elastic modulus contrast between coal and gangue layers,interfacial stress differential,and interfacial cohesion at coal-gangue interfaces are critical factors governing hydraulic fracture penetration through these interfaces.High vertical stress differences(>3 MPa)inhibit interfacial dilation,promoting predominant crosslayer fracture propagation.Reduced interfacial stress contrasts and enhanced interfacial cohesion facilitate fracture penetration across interfaces.Furthermore,smaller elastic modulus contrasts between coal and gangue correlate with increased interfacial aperture.Finally,lower injection rates effectively suppress vertical fracture propagation in deep coal reservoirs.This study elucidates the characteristics and mechanisms governing cross-layer fracture propagation in coal–rock composites with interbedded partings,and delineates the dynamic evolution laws and dominant controlling factors involved.Thefindings provide critical theoretical insights for the optimization of fracture design and the efficient development of deep coalbed methane reservoirs.
基金supported by the National Natural Science Foundation of China(Grant Nos.12388101 and 12472221)the Fundamental Research Funds for the Central Universities(Grant No.lzujbky-2024-oy10).
文摘In sediment transport on a mobile erodible bed,near-bed particles tend to preferentially locate under specific flow regions and form an uneven bedform.These moving and mobile particles can significantly modulate turbulence at various scales,from inertial large-scale motions to small viscous motions.This study analyzes the particle-resolved direct numerical simulation data of particle-laden two-phase flow with multilayers of particles in turbulent flows over static and mobile beds.The double-average method is adopted for energy transfer analysis.The result shows that the alternative streaky bedform in the spanwise directions correlates with the streak structures in the near-wall turbulence in the mobile bed case.The energy redistribution and exchange,as well as the dissipation,are analyzed in detail,and an energy transfer diagram is given in the last to summarize the energy transfer processes.In both the static and mobile bed cases,flow energy is introduced into the system via the work performed by volume forces acting on the mean flow.The viscous dissipations in the double mean and form-induced fields are more pronounced in the static bed case,and the work done by the fluid-particle interfacial stress in the double mean and turbulent fields is more pronounced in the mobile bed case.The prominent energy contribution in the form-induced field is the production by the form-induced stress on the mean strain in the mobile bed case.In addition,sediment transport involving a limited number of mobile particles is insufficient to capture the energy transfer processes that occur over the troughs and may intertwine the energy transfer processes over the mobile particles and the fixed particle bed.
基金financially supported by the National Key Research and Development Program of China (2022YFB3706802)。
文摘Automation and intelligence have become the primary trends in the design of investment casting processes.However,the design of gating and riser systems still lacks precise quantitative evaluation criteria.Numerical simulation plays a significant role in quantitatively evaluating current processes and making targeted improvements,but its limitations lie in the inability to dynamically reflect the formation outcomes of castings under varying process conditions,making real-time adjustments to gating and riser designs challenging.In this study,an automated design model for gating and riser systems based on integrated parametric 3D modeling-simulation framework is proposed,which enhances the flexibility and usability of evaluating the casting process by simulation.Firstly,geometric feature extraction technology is employed to obtain the geometric information of the target casting.Based on this information,an automated design framework for gating and riser systems is established,incorporating multiple structural parameters for real-time process control.Subsequently,the simulation results for various structural parameters are analyzed,and the influence of these parameters on casting formation is thoroughly investigated.Finally,the optimal design scheme is generated and validated through experimental verification.Simulation analysis and experimental results show that using a larger gate neck(24 mm in side length) and external risers promotes a more uniform temperature distribution and a more stable flow state,effectively eliminating shrinkage cavities and enhancing process yield by 15%.
基金Supported by the National Natural Science Foundation of China under Grant No.51975138the High-Tech Ship Scientific Research Project from the Ministry of Industry and Information Technology under Grant No.CJ05N20the National Defense Basic Research Project under Grant No.JCKY2023604C006.
文摘Marine thin plates are susceptible to welding deformation owing to their low structural stiffness.Therefore,the efficient and accurate prediction of welding deformation is essential for improving welding quality.The traditional thermal elastic-plastic finite element method(TEP-FEM)can accurately predict welding deformation.However,its efficiency is low because of the complex nonlinear transient computation,making it difficult to meet the needs of rapid engineering evaluation.To address this challenge,this study proposes an efficient prediction method for welding deformation in marine thin plate butt welds.This method is based on the coupled temperature gradient-thermal strain method(TG-TSM)that integrates inherent strain theory with a shell element finite element model.The proposed method first extracts the distribution pattern and characteristic value of welding-induced inherent strain through TEP-FEM analysis.This strain is then converted into the equivalent thermal load applied to the shell element model for rapid computation.The proposed method-particularly,the gradual temperature gradient-thermal strain method(GTG-TSM)-achieved improved computational efficiency and consistent precision.Furthermore,the proposed method required much less computation time than the traditional TEP-FEM.Thus,this study lays the foundation for future prediction of welding deformation in more complex marine thin plates.
