To analyze the stress of the guiding & positioning board and the effectiveness of the guiding & positioning device,according to guiding & positioning device's operational principle and structure,the gu...To analyze the stress of the guiding & positioning board and the effectiveness of the guiding & positioning device,according to guiding & positioning device's operational principle and structure,the guiding & positioning board's motion regular was analyzed by diagrammatical method based on 2 postulated conditions.Considering about the working conditions' change,simulations in 5 different kinds of working conditions were done to check the correctness of the motion regulars obtained by diagrammatical method.Simulation results prove that the motion regulars are right,the postulated conditions have no effect on the obtained motion regulars.According to the simulation results,the motion processs's characters were drawn out at the same time.展开更多
In the present work,the hydrodynamic performance of the double deflector rectangular cambered otter board was studied using wind tunnel experiment,flume tank experiment and numerical simulation.Results showed that the...In the present work,the hydrodynamic performance of the double deflector rectangular cambered otter board was studied using wind tunnel experiment,flume tank experiment and numerical simulation.Results showed that the otter board had a good hydrodynamic performance with the maximum lift-to-drag ratio(K_(MAX) = 3.70).The flow separation occurred when the angle of attack(AOA) was at 45?,which revealed that the double deflector structure of the otter board can delay the flow separation.Numerical simulation results showed a good agreement with experiment ones,and could predict the critical AOA,which showed that it can be used to study the hydrodynamic performance of the otter board with the advantage of flow visualization.However,the drag coefficient in flume tank was much higher than that in wind tunnel,which resulted in a lower lift-to-drag ratio.These may be due to different fluid media between flume tank and wind tunnel,which result in the big difference of the vortexes around the otter board.Given the otter boards are operated in water,it was suggested to apply both flume tank experiment and numerical simulation to study the hydrodynamic performance of otter board.展开更多
The splitter is an important component of water-based cooling systems used to extract heat from computer boards.In the present study,the flow characteristics of a 16-splitter structure were numerically simulated and c...The splitter is an important component of water-based cooling systems used to extract heat from computer boards.In the present study,the flow characteristics of a 16-splitter structure were numerically simulated and compared with experimental results to verify the reliability of the numerical simulation method.Accordingly,the concept of splitter structural coefficients was proposed.Based on the results of this study,we recommend a selection range of 5≤k≤6 for the structure factor k of the splitter;after optimization,the maximum deviation of the splitter outlet flow was reduced from the original value of 100%to 8.3%.展开更多
In this paper, a 3D model of a flat circuit board with a heat generating electronic chip mounted on it has been studied numerically. The conjugate heat transfer including the conduction in the chip and convection with...In this paper, a 3D model of a flat circuit board with a heat generating electronic chip mounted on it has been studied numerically. The conjugate heat transfer including the conduction in the chip and convection with the surrounding fluid has been investigated numerically. Computational fluid dynamics using the finite volume method has been used for modeling the conjugate heat transfer through the chip and the circuit board. Conjugate heat transfer has broad applications in engineering and industrial applications in design of cooling off electronic components. Effects of various inlet velocities have been studied on the heat transfer variation and temperature of the circuit board. Numerical results show that the temperature of the chip reduces as the velocity of the inlet fluid flow increases.展开更多
基金SRF of HLJ (No.F2004-15)SRF of HIT (No.HIT2003.20)
文摘To analyze the stress of the guiding & positioning board and the effectiveness of the guiding & positioning device,according to guiding & positioning device's operational principle and structure,the guiding & positioning board's motion regular was analyzed by diagrammatical method based on 2 postulated conditions.Considering about the working conditions' change,simulations in 5 different kinds of working conditions were done to check the correctness of the motion regulars obtained by diagrammatical method.Simulation results prove that the motion regulars are right,the postulated conditions have no effect on the obtained motion regulars.According to the simulation results,the motion processs's characters were drawn out at the same time.
基金supported by the National Key Technology R&D Program(No.2013BAD13B03)the Key R&D Project from Science and Technology Department of Zhejiang Province(Nos.2018C02026,2018C02040)+1 种基金the National Natural Science Foundation of China(No.31072246)the Fundamental Research Funds for the Central Universities(No.201564020)
文摘In the present work,the hydrodynamic performance of the double deflector rectangular cambered otter board was studied using wind tunnel experiment,flume tank experiment and numerical simulation.Results showed that the otter board had a good hydrodynamic performance with the maximum lift-to-drag ratio(K_(MAX) = 3.70).The flow separation occurred when the angle of attack(AOA) was at 45?,which revealed that the double deflector structure of the otter board can delay the flow separation.Numerical simulation results showed a good agreement with experiment ones,and could predict the critical AOA,which showed that it can be used to study the hydrodynamic performance of the otter board with the advantage of flow visualization.However,the drag coefficient in flume tank was much higher than that in wind tunnel,which resulted in a lower lift-to-drag ratio.These may be due to different fluid media between flume tank and wind tunnel,which result in the big difference of the vortexes around the otter board.Given the otter boards are operated in water,it was suggested to apply both flume tank experiment and numerical simulation to study the hydrodynamic performance of otter board.
文摘The splitter is an important component of water-based cooling systems used to extract heat from computer boards.In the present study,the flow characteristics of a 16-splitter structure were numerically simulated and compared with experimental results to verify the reliability of the numerical simulation method.Accordingly,the concept of splitter structural coefficients was proposed.Based on the results of this study,we recommend a selection range of 5≤k≤6 for the structure factor k of the splitter;after optimization,the maximum deviation of the splitter outlet flow was reduced from the original value of 100%to 8.3%.
文摘In this paper, a 3D model of a flat circuit board with a heat generating electronic chip mounted on it has been studied numerically. The conjugate heat transfer including the conduction in the chip and convection with the surrounding fluid has been investigated numerically. Computational fluid dynamics using the finite volume method has been used for modeling the conjugate heat transfer through the chip and the circuit board. Conjugate heat transfer has broad applications in engineering and industrial applications in design of cooling off electronic components. Effects of various inlet velocities have been studied on the heat transfer variation and temperature of the circuit board. Numerical results show that the temperature of the chip reduces as the velocity of the inlet fluid flow increases.
