The effects of solution treatment on the evolution of the second phases and mechanical properties of7075Al alloy werestudied with scanning electron microscopy(SEM),energy dispersive X-ray spectrometry(EDS),differentia...The effects of solution treatment on the evolution of the second phases and mechanical properties of7075Al alloy werestudied with scanning electron microscopy(SEM),energy dispersive X-ray spectrometry(EDS),differential scanning calorimetry(DSC),hardness and tensile tests.The results show that Mg(Zn,Cu,Al)2phases gradually dissolve into the matrix,yet the size andmorphology of Al7Cu2Fe phase exhibit no change with the increase of the solution treatment temperature and time due to its highmelting point.When the solution treatment temperature and time continue to increase,the formation of coarse black Mg2Si particlesoccurs.Compared to the as-cast alloy,the microhardness,tensile strength,and elongation of the sample under solution heat treatmentat460°C for5h are increased by55.1%,40.9%and109.1%,respectively.This is because the eutectic Mg(Zn,Cu,Al)2phases almostcompletely dissolve and basically no coarse black Mg2Si particles are formed.展开更多
The effects of second phases on the fracture behavior of Mg-10Gd-3Y-0.6Zr alloy were investigated.The results show that the fracture mode can be generally described as ductile transgranular fracture in as-extruded con...The effects of second phases on the fracture behavior of Mg-10Gd-3Y-0.6Zr alloy were investigated.The results show that the fracture mode can be generally described as ductile transgranular fracture in as-extruded condition and intergranular fracture in peak-aged condition.In as-extruded condition,the ductile transgranular fracture occurs by the formation and transgranular propagation of the microcrack from the broken primary phases.However,as the collaboration effects of precipitates inside grains and on the grain boundaries have the tendency to reduce the cohesive strength of the grain boundary,and make the grain boundaries the favorable path for crack propagation,the intergranular fracture occurs in peak-aged condition.展开更多
Alloying combined with plastic deformation processing is widely used to improve mechanical properties of pure Zn.As-cast Zn and its alloys are brittle.Beside plastic deformation processing,no effective method has yet ...Alloying combined with plastic deformation processing is widely used to improve mechanical properties of pure Zn.As-cast Zn and its alloys are brittle.Beside plastic deformation processing,no effective method has yet been found to eliminate the brittleness and even endow room temperature super-ductility.Second phase,induced by alloying,not only largely determines the ability of plastic deformation,but also influences strength,corrosion rate and cytotoxicity.Controlling second phase is important for designing biodegradable Zn alloys.In this review,knowledge related to second phases in biodegradable Zn alloys has been analyzed and summarized,including characteristics of binary phase diagrams,volume fraction of second phase in function of atomic percentage of an alloying element,and so on.Controversies about second phases in Zn-Li,Zn-Cu and Zn-Fe systems have been settled down,which benefits future studies.The effects of alloying elements and second phases on microstructure,strength,ductility,corrosion rate and cytotoxicity have been neatly summarized.Mg,Mn,Li,Cu and Ag are recommended as the major alloying elements,owing to their prominent beneficial effects on at least one of the above properties.In future,synergistic effects of these elements should be more thoroughly investigated.For other nutritional elements,such as Fe and Ca,refining second phase is a matter of vital concern.展开更多
The mechanism of strength and toughness variation in Ti microalloyed steel within the range of 0.04–0.157 wt.%was investigated.By adding 0.13 wt.%Ti,the steel achieves higher strength while maintaining a certain leve...The mechanism of strength and toughness variation in Ti microalloyed steel within the range of 0.04–0.157 wt.%was investigated.By adding 0.13 wt.%Ti,the steel achieves higher strength while maintaining a certain level of elongation and low-temperature impact toughness.With increasing Ti content,the grain size in the steel decreased from 17.7 to 8.9μm.This decrease in grain size is accompanied by an increase in the percentage of low-angle grain boundaries and dislocations,which act as barriers to hinder crack propagation.The Ti microalloyed steel exhibits a 20%increase in yield strength and a 14%increase in tensile strength.The transformation of steel plasticity occurs when the Ti content exceeds 0.102 wt.%.The low-temperature impact toughness of the steel gradually decreases with increasing Ti content.At low Ti content,the low-temperature impact toughness is reduced due to crack initiation by large-size inclusions.At high Ti content,the low-temperature impact toughness of the steel deteriorates due to several factors.These include the narrower tough–brittle transition zone,grain boundary embrittlement caused by small-sized grains,and the decrease in the solid solution strengthening effect.展开更多
Microstructure and corrosion resistance of an as-cast Mg-14Li-8Zn(in wt.%,LZ148)alloy subjected to solid solution treatment(T4)and aging treatment(T6)were investigated.The results revealed that the large eutectic MgLi...Microstructure and corrosion resistance of an as-cast Mg-14Li-8Zn(in wt.%,LZ148)alloy subjected to solid solution treatment(T4)and aging treatment(T6)were investigated.The results revealed that the large eutectic MgLi_(2)Zn(θ’)phase formed in as-cast LZ148 alloy were completely dissolved intoβ-Li matrix after T4 treatment,and meanwhile nanoθ’phase could be rapidly precipitated in T4 sample,and then theθ’nanoprecipitates transformed into MgLiZn(θ)phase with a moderate size after T6 treatment.The as-cast sample presented the worst corrosion resistance due to the occurrence of strong micro-galvanic effect between the cathodic eutecticθ’phase and anodicβ-Li matrix.After T4 treatment,the corrosion resistance of as-cast LZ148 alloy was dramatically improved,which was primarily ascribed to the trivial micro-galvanic effect due to the absence of noble eutecticθ’phase.In addition,the dispersed MgLi2Zn nano-precipitates and/or the homogenized distribution of alloying elements in matrix were also beneficial for the improved corrosion resistance of T4 sample.Furthermore,the lower local strain energy in the matrix of T4 sample could also contribute to the excellent corrosion resistance.However,the precipitatedθphases in T6 sample were detrimental to further improve corrosion performance due to the reactivated micro-galvanic effect.At last,the main compositions of surface film on the three samples were also revealed in detail,attributing to the different corrosion resistance of three samples as well.展开更多
The main methods of the second phase quantitative analysis in current material science researches are manual recognition and extracting by using software such as Image Tool and Nano Measurer. The weaknesses such as hi...The main methods of the second phase quantitative analysis in current material science researches are manual recognition and extracting by using software such as Image Tool and Nano Measurer. The weaknesses such as high labor intensity and low accuracy statistic results exist in these methods. In order to overcome the shortcomings of the current methods, the Ω phase in A1-Cu-Mg-Ag alloy is taken as the research object and an algorithm based on the digital image processing and pattern recognition is proposed and implemented to do the A1 alloy TEM （transmission electron microscope） digital images process and recognize and extract the information of the second phase in the result image automatically. The top-hat transformation of the mathematical morphology, as well as several imaging processing technologies has been used in the proposed algorithm. Thereinto, top-hat transformation is used for elimination of asymmetric illumination and doing Multi-layer filtering to segment Ω phase in the TEM image. The testing results are satisfied, which indicate that the Ω phase with unclear boundary or small size can be recognized by using this method. The omission of these two kinds of Ω phase can be avoided or significantly reduced. More Ω phases would be recognized （growing rate minimum to 2% and maximum to 400% in samples）, accuracy of recognition and statistics results would be greatly improved by using this method. And the manual error can be eliminated. The procedure recognizing and making quantitative analysis of information in this method is automatically completed by the software. It can process one image, including recognition and quantitative analysis in 30 min, but the manual method such as using Image Tool or Nano Measurer need 2 h or more. The labor intensity is effectively reduced and the working efficiency is greatly improved.展开更多
Increasing the hole expansion ratio is significant for developing high formability parts.Hole expansion tests were carried out on low carbon hot-rolled steel containing 0.11%Ti,0.072%Ti–0.03%Nb and 0.097%Ti–0.059%Nb...Increasing the hole expansion ratio is significant for developing high formability parts.Hole expansion tests were carried out on low carbon hot-rolled steel containing 0.11%Ti,0.072%Ti–0.03%Nb and 0.097%Ti–0.059%Nb,respectively.The effects of microstructure,texture,crack propagation behavior and second phase precipitation behavior on hole expansion ratio were investigated.The precipitation behavior of TiC and(Ti,Nb)C in austenite and ferrite in three groups of steel samples was calculated theoretically.The results showed that the hole expansion ratios of 0.11Ti,0.072Ti–0.03Nb and 0.097Ti–0.059Nb test steels were 51.73%,51.17%and 66.24%following simulated coiling at 600℃,respectively.The microstructure was mainly polygonal ferrite with a small amount of pearlite.The grain refinement of 0.097Ti–0.059Nb test steel and the low texture ratio of{110}//ND improved the hole expansion ratio.The low overall hole expansion ratio was due to the microstructure inhomogeneity.The microstructure uniformity was improved by the quenching and tempering treatment,and the hole expansion ratio of the three test steels was greatly increased.The fastest precipitation temperatures in the austenitic region of 0.11Ti,0.072Ti–0.03Nb and 0.097Ti–0.059Nb test steels were 880,860 and 830℃,while those in the ferrite region were 680,675 and 675℃,respectively.The addition of Nb element increased the volume free energy,so that the critical core size of the nucleation on the dislocation line increased,resulting in the decrease in the fastest precipitation temperature.展开更多
The group Ⅳ–Ⅵ semiconductor,SnSe,is abundant on the earth and is a promising thermoelectric(TE)material due to its low thermal conductivity.However,the p-type SnSe polycrystals have low electrical conductivities du...The group Ⅳ–Ⅵ semiconductor,SnSe,is abundant on the earth and is a promising thermoelectric(TE)material due to its low thermal conductivity.However,the p-type SnSe polycrystals have low electrical conductivities due to their low carrier concentration,significantly limiting their further applications.This study introduced the argyrodite-type Ag_(9)GaSe_(6) compound into the SnSe matrix to effectively increase the hole carrier concentration,increasing the electrical conductivity.A high electrical conductivity of 50.5 S cm^(−1) was obtained for the SnSe+0.5 wt%Ag_(9)GaSe_(6) sample at 323 K.Due to the increased electrical conductivity,the SnSe+0.5 wt%Ag_(9)GaSe_(6) sample had an average power factor(PFave)value of~410μW m^(-1) K^(-2) in the 323–823 K temperature range,a nearly four times enhancement compared to the undoped SnSe sample.Additionally,the thermal conductivity slightly increased due to the introduction of the Ag_(9)GaSe_(6) compound.However,the electrical transport properties were significantly enhanced,making up for the improvement in thermal conductivity.Consequently,the SnSe+0.5 wt%Ag_(9)GaSe_(6) sample obtained a peak thermoelectric figure of merit ZT value of~1.2 at 823 K and a ZT_(ave) value of 0.58 in the 323–823 K temperature range.The proposed strategy improved the ZT and ZT_(ave) values of SnSe-based TE materials at room temperature and provided a systematic strategy for modifying SnSe-based TE materials.Moreover,the thermoelectric properties of SnSe can be effectively improved by introducing the Ag_(9)GaSe_(6) compound for doping,and waste heat power generation can be effectively carried out in the middle temperature region.展开更多
Effect of the second phase in the micro-galvanic corrosion of a commercial Mg alloy containing rare earth elements, cast WE43 alloy,was investigated in 0.6 M NaCl solution and 0.6 M Na_(2)SO_(4)solution by scanning el...Effect of the second phase in the micro-galvanic corrosion of a commercial Mg alloy containing rare earth elements, cast WE43 alloy,was investigated in 0.6 M NaCl solution and 0.6 M Na_(2)SO_(4)solution by scanning electron microscopy(SEM) observations, scanning Kelvin probe force microscopy(SKPFM) analysis, hydrogen evolution, weight loss measurement, and electrochemical techniques. It is confirmed that the second phase of cast WE43 alloy is more active than Mg matrix and exhibits an anodic role in the micro-galvanic corrosion with α-Mg matrix as cathode and dissolves preferentially in Na_(2)SO_(4)solution, in contrast to the situation in NaCl solution. The corrosion rate of cast WE43 alloy in Na_(2)SO_(4)solution is much higher than that in NaCl solution, which is different from the conventional wisdom and could be attributed to the different role of the second phase in the micro-galvanic corrosion in two solutions.展开更多
To investigate the effect of separate Al_(2)Ca and Mg_(2)Ca phases on the corrosion properties of Mg−Al−Ca−Mn alloys,OM,SEM,immersion and electrochemical tests were conducted on the as-cast and ECAP Al_(2)Ca-containin...To investigate the effect of separate Al_(2)Ca and Mg_(2)Ca phases on the corrosion properties of Mg−Al−Ca−Mn alloys,OM,SEM,immersion and electrochemical tests were conducted on the as-cast and ECAP Al_(2)Ca-containing(2Ca)and Mg_(2)Ca-containing(4Ca)alloys.At the beginning of corrosion,the two as-cast alloys are corroded slowly compared with ECAP alloys.With prolonging the corrosion time,the corrosion of ECAP alloys becomes slighter than that of as-cast alloys,which is mainly ascribed to the dispersion and refinement of the second phase in ECAP alloys.Moreover,the corrosion degree of 2Ca alloys is always slighter than that of 4Ca alloys,suggesting that Al_(2)Ca phase is more beneficial to the enhancement of corrosion resistance of Mg−Al−Ca−Mn based alloys than Mg_(2)Ca phase.Finally,based on the examinations of corrosion surface and electrochemical testing results,different corrosion mechanisms caused by the distributions and morphology of Al_(2)Ca and Mg_(2)Ca phases are discussed.展开更多
The effect of equal-channel angular pressing(ECAP)processing at room temperature and 300℃on the distribution of the second phase particles and its influence on hardness and electrical conductivity of the commercial C...The effect of equal-channel angular pressing(ECAP)processing at room temperature and 300℃on the distribution of the second phase particles and its influence on hardness and electrical conductivity of the commercial Cu-0.81Cr-0.07Zr alloy were investigated.Microstructural characterization indicated that the area fraction of coarse Cr-rich particles decreased after ECAP processing.This reduction was attributed to the Cr dissolution induced by plastic deformation.The electrical conductivity of the alloy decreased by 12%after 4 ECAP passes at room temperature due to the increase of electrons scattering caused by higher Cr content in solid solution and higher density of defects in the matrix.These results were supported by the reduction of the Cu lattice parameter and by the exothermic reactions,during differential scanning calorimetry(DSC)analysis,observed only in the samples subjected to ECAP processing.Aging heat treatment after ECAP processing promoted an additional hardening effect and the complete recuperation of the electrical conductivity,caused by the re-precipitation of the partially dissolved particles.The better combination of hardness(191 HV)and electrical conductivity(83.5%(IACS))was obtained after 4 ECAP passes at room temperature and subsequent aging at 380℃for 1 h.展开更多
Microstructure evolution and damping capacities of Mg–Ce binary alloys with three different Ce contents（0.5, 1, or 2 wt%） have been systematically investigated in this work. Numerous fine parallel second phases in...Microstructure evolution and damping capacities of Mg–Ce binary alloys with three different Ce contents（0.5, 1, or 2 wt%） have been systematically investigated in this work. Numerous fine parallel second phases in Mg–2Ce alloy are obtained, as well as a large number of dislocations around them, but few dislocations appear around the reticular second phase in the Mg–1Ce alloy. Among the three alloys, two internal friction peaks（P;and P;） are detected at about 78 and 167?C in both the Mg–0.5Ce and Mg–1Ce alloys.In addition, the alloy with special parallel second phase structure exhibits excellent damping capacity in both strain amplitude and temperature-dependent regions. These results may be ascribed to the stress concentration and the formation of abundant parallel and uniform dislocation configurations in the ?-Mg matrix without the influence of crystal orientation. The obtained results may provide a novel idea to prepare high-damping magnesium alloys by tailoring their microstructure.展开更多
The morphology and size of second phase greatly influence the strengthening effect on oxidation dispersion strengthened Mo alloys.In this work,a novel nanostructuring strategy is adopted to modify the second phase of ...The morphology and size of second phase greatly influence the strengthening effect on oxidation dispersion strengthened Mo alloys.In this work,a novel nanostructuring strategy is adopted to modify the second phase of Y_(2)O_(3),and the corresponding effects of particle shape and size on mechanical properties of sintered Mo−Y_(2)O_(3) alloys were investigated.It is found that spherical particles with sizes below 200 nm are preferred due to the dominant intragranular distribution of second phases associated with better strengthening effect originating from dislocation pinning.With smaller particle size of Y_(2)O_(3) nanospheres(105 nm),the tensile strength of corresponding Mo alloy is enhanced by about 43.8%,much higher than that(8.3%)reinforced by second phase nanospheres with larger particle size(322 nm).Meanwhile,with similar particle size(around 100 nm),the spherical shape exhibits better strengthening effect than the one reinforced by one-dimensional rod-like second phase.展开更多
Two types of stress relaxation tests were carried out to investigate the incubation time for incipient precipi-tation of Ti（C,N） in deformed austenite and （Ti,Mo）C in ferrite of ferritic Ti-Mo microalloyed steel T...Two types of stress relaxation tests were carried out to investigate the incubation time for incipient precipi-tation of Ti（C,N） in deformed austenite and （Ti,Mo）C in ferrite of ferritic Ti-Mo microalloyed steel The size dis-tribution, amount and chemical composition of precipitates were obtained by using physicochemical phase analysis, and calculated according to thermodynamics and kinetics. The experimental results demonstrated that the incubation time was reduced with increasing Ti content, and prolonged with the addition of Mo. After 30 % deformation at 850 ℃, the nucleation of strain-induced Ti（C,N） was a relatively slow process. On the other hand, the temperature where the nucleation rate of （Ti, Mo）C in ferrite was the highest descended first and then ascended with increasing Ti content, and so did the temperature where the incubation time was the shortest. The key point is that the tempera-ture of steel containing about 0.09 % Ti is the lowest. The mass fraction of MC-type particles with size smaller than 10 nm in steel containing 0.09% Ti and 0.2% Mo reached 73.7%. The size distributions of precipitates in steel containing 0.09% Ti were relatively concentrated compared with that in steel containing 0.07% Ti.展开更多
Alloys with composition of Mg_(96-x)Gd_3Zn_1Li_x(at.%)(x=0, 2, 4, and 6) were prepared by conventional casting. The microstructures of these alloys under as-cast and solid-solution conditions have been observed, and t...Alloys with composition of Mg_(96-x)Gd_3Zn_1Li_x(at.%)(x=0, 2, 4, and 6) were prepared by conventional casting. The microstructures of these alloys under as-cast and solid-solution conditions have been observed, and the mechanical properties were investigated. The results showed that Li is an effective element to refine the grains and break the eutectic networks in as-cast MgGd_3Zn_1 alloy. During solid solution treatment, these broken eutectic networks are spheroidized and highly dispersed. In addition, plentiful lamellar long period stacking ordered(LPSO) phases are precipitated in an α-Mg matrix when the Li addition is not more than 4%. Solid-solution treated Mg_(92)Gd_3Zn_1Li_4 alloy exhibits an optimal ultimate tensile strength(UTS) of 226 MPa and elongation of 5.8%. The strength of MgGd_3Zn_1 alloy is improved significantly, meanwhile, the toughness is apparently increased.展开更多
The phase diagram of superaustenitic stainless steel 654SMO was calculated by thermodynamic software and the precipitated phases in the specimens aged at 800-1100°C for 1hwere studied by methods of physicochemica...The phase diagram of superaustenitic stainless steel 654SMO was calculated by thermodynamic software and the precipitated phases in the specimens aged at 800-1100°C for 1hwere studied by methods of physicochemical phase analysis,scanning electron microscopy and transmission electron microscopy.The results showed that the size of precipitated particles increased with increasing the temperature.The amount of second phases reached the maximum value at 900°C,but decreased above 900°C.There were about eight kinds of precipitated phases in 654SMO includingσphase,Cr_2N,μphase,χphase,Laves phase,M_（23）C_6,M_6C and M_3C,in which theσphase and Cr_2N were the dominant precipitated phases.展开更多
The selective abnormal growth of Goss grains in magnetic sheets of Fe-3%Si （grade Hi-B） induced by second-phase particles （AlN and MnS） was studied using a modified Monte Carlo Ports model. The starting microstruc...The selective abnormal growth of Goss grains in magnetic sheets of Fe-3%Si （grade Hi-B） induced by second-phase particles （AlN and MnS） was studied using a modified Monte Carlo Ports model. The starting microstructures for the simulations were generated from electron backscatter diffraction （EBSD） orientation imaging maps of recrystallized samples. In the simulation, second-phase particles were assumed to be randomly distributed in the initial microstructures and the Zener drag effect of particles on Goss grain boundaries was assumed to be selectively invalid because of the unique properties of Goss grain boundaries. The simulation results suggest that normal growth of the matrix grains stagnates because of the pinning effect of particles on their boundaries. During the onset of abnormal grain growth, some Goss grains with concave boundaries in the initial microstructure grow fast abnormally and other Goss grains with convex boundaries shrink and eventually disappear.展开更多
The second phase particle effect on texture evolution of polycrystalline material is studied through phase-field method. A unique field variable is introduced into the phase-field model to represent the second phase p...The second phase particle effect on texture evolution of polycrystalline material is studied through phase-field method. A unique field variable is introduced into the phase-field model to represent the second phase particles. Elastic interaction between particles and grains is also considered. Results indicate that in the presence of second phase particles the average particle diameter turns smaller than in the absence of these particles and retards texture formation by pinning effect. The second phase particles change the strain energy profile, which tremendously influences the pinning effect.展开更多
The second phase particle dispersed in microalloyed steel has different effects on grain growth depending on their size and volume fiaction of the second phase particles which will change during welding thermal cycles...The second phase particle dispersed in microalloyed steel has different effects on grain growth depending on their size and volume fiaction of the second phase particles which will change during welding thermal cycles. The particle coarsening and dissolution kinetics model was analyzed for continuous heating and cooling. In addition, based on experimental data, the coupled equation of grain growth was established by introducing limited size of grain growth with the consideration of the second phase particles pinning effects. Using Monte Carlo method based on experimental data model, the grain growth simulation for heat-affected zone of microalloyed steel welds was achieved. The calculating results were well in agreement with that of experiments.展开更多
In order to control the grain size during hot forming,grain growth behavior of a pre-extruded Mg-6Zn magnesium alloy and its correlation with solute and second phase distribution were investigated.Isothermal annealing...In order to control the grain size during hot forming,grain growth behavior of a pre-extruded Mg-6Zn magnesium alloy and its correlation with solute and second phase distribution were investigated.Isothermal annealing was conducted on a Gleeble-1500 thermo-mechanical simulator.The mean grain size Dg of each annealed specimen was measured by the quantitative metallography technique.The grain growth kinetics of the Mg-6Zn alloy annealed at 473-623 K was obtained as Dg^4- Dg0^4=2.25 ×10^11 exp（-95450）by the least square linear regression method.The deviation of grain growth exponent n = 4 from the theoretical value of 2 may be attributed to the presence of solute zinc and second phases which will retard the boundary migration.Microscopic observations show that the non-uniform distribution of grain size for samples pre-extruded or annealed at low temperatures is closely related to the non-uniform distribution of fine and dispersed second phases but not to the non-uniform distribution of solute zinc.This indicates that second phase pinning effect plays an important role in microstructure refinement.展开更多
基金Project(51364035)supported by the National Natural Science Foundation of ChinaProject(CX2015055)supported by the Innovation Special Funds of Nanchang University for Graduate Student,China
文摘The effects of solution treatment on the evolution of the second phases and mechanical properties of7075Al alloy werestudied with scanning electron microscopy(SEM),energy dispersive X-ray spectrometry(EDS),differential scanning calorimetry(DSC),hardness and tensile tests.The results show that Mg(Zn,Cu,Al)2phases gradually dissolve into the matrix,yet the size andmorphology of Al7Cu2Fe phase exhibit no change with the increase of the solution treatment temperature and time due to its highmelting point.When the solution treatment temperature and time continue to increase,the formation of coarse black Mg2Si particlesoccurs.Compared to the as-cast alloy,the microhardness,tensile strength,and elongation of the sample under solution heat treatmentat460°C for5h are increased by55.1%,40.9%and109.1%,respectively.This is because the eutectic Mg(Zn,Cu,Al)2phases almostcompletely dissolve and basically no coarse black Mg2Si particles are formed.
基金Project(IRT0713)supported by the Program for Changjiang Scholars and Innovative Research Team in Chinese UniversityProjects(2007CB613701,2007CB613702)supported by National Basic Research Program of China
文摘The effects of second phases on the fracture behavior of Mg-10Gd-3Y-0.6Zr alloy were investigated.The results show that the fracture mode can be generally described as ductile transgranular fracture in as-extruded condition and intergranular fracture in peak-aged condition.In as-extruded condition,the ductile transgranular fracture occurs by the formation and transgranular propagation of the microcrack from the broken primary phases.However,as the collaboration effects of precipitates inside grains and on the grain boundaries have the tendency to reduce the cohesive strength of the grain boundary,and make the grain boundaries the favorable path for crack propagation,the intergranular fracture occurs in peak-aged condition.
基金financially supported by National Key R&D Program of China(2016YFC1102500).
文摘Alloying combined with plastic deformation processing is widely used to improve mechanical properties of pure Zn.As-cast Zn and its alloys are brittle.Beside plastic deformation processing,no effective method has yet been found to eliminate the brittleness and even endow room temperature super-ductility.Second phase,induced by alloying,not only largely determines the ability of plastic deformation,but also influences strength,corrosion rate and cytotoxicity.Controlling second phase is important for designing biodegradable Zn alloys.In this review,knowledge related to second phases in biodegradable Zn alloys has been analyzed and summarized,including characteristics of binary phase diagrams,volume fraction of second phase in function of atomic percentage of an alloying element,and so on.Controversies about second phases in Zn-Li,Zn-Cu and Zn-Fe systems have been settled down,which benefits future studies.The effects of alloying elements and second phases on microstructure,strength,ductility,corrosion rate and cytotoxicity have been neatly summarized.Mg,Mn,Li,Cu and Ag are recommended as the major alloying elements,owing to their prominent beneficial effects on at least one of the above properties.In future,synergistic effects of these elements should be more thoroughly investigated.For other nutritional elements,such as Fe and Ca,refining second phase is a matter of vital concern.
基金supported by the National Natural Science Foundation of China(Nos.52174311 and 51974020).
文摘The mechanism of strength and toughness variation in Ti microalloyed steel within the range of 0.04–0.157 wt.%was investigated.By adding 0.13 wt.%Ti,the steel achieves higher strength while maintaining a certain level of elongation and low-temperature impact toughness.With increasing Ti content,the grain size in the steel decreased from 17.7 to 8.9μm.This decrease in grain size is accompanied by an increase in the percentage of low-angle grain boundaries and dislocations,which act as barriers to hinder crack propagation.The Ti microalloyed steel exhibits a 20%increase in yield strength and a 14%increase in tensile strength.The transformation of steel plasticity occurs when the Ti content exceeds 0.102 wt.%.The low-temperature impact toughness of the steel gradually decreases with increasing Ti content.At low Ti content,the low-temperature impact toughness is reduced due to crack initiation by large-size inclusions.At high Ti content,the low-temperature impact toughness of the steel deteriorates due to several factors.These include the narrower tough–brittle transition zone,grain boundary embrittlement caused by small-sized grains,and the decrease in the solid solution strengthening effect.
基金Tplied Basic Research Foundation of Guangdong Province(Grant Nos.2024A1515030065,2023A1515012299 and2023A1515010075)Basic and Applied Basic ResearchProject of Guangzhou(Grant Nos.2024A04J6299 and202201011454)+3 种基金Young Talent Support Project·of Guangzhou Association for Science and Technology(Grant No.QT2024-012)National Natural Science Foundation of China(Grant Nos.52101283 and 52101132)Young Elite Scientist Spon-sorship Program by CAST(Grant No.YESS20230412)National College Students Innovation and EntrepreneurshipTraining Program(Grant No.xj2024118450706)。
文摘Microstructure and corrosion resistance of an as-cast Mg-14Li-8Zn(in wt.%,LZ148)alloy subjected to solid solution treatment(T4)and aging treatment(T6)were investigated.The results revealed that the large eutectic MgLi_(2)Zn(θ’)phase formed in as-cast LZ148 alloy were completely dissolved intoβ-Li matrix after T4 treatment,and meanwhile nanoθ’phase could be rapidly precipitated in T4 sample,and then theθ’nanoprecipitates transformed into MgLiZn(θ)phase with a moderate size after T6 treatment.The as-cast sample presented the worst corrosion resistance due to the occurrence of strong micro-galvanic effect between the cathodic eutecticθ’phase and anodicβ-Li matrix.After T4 treatment,the corrosion resistance of as-cast LZ148 alloy was dramatically improved,which was primarily ascribed to the trivial micro-galvanic effect due to the absence of noble eutecticθ’phase.In addition,the dispersed MgLi2Zn nano-precipitates and/or the homogenized distribution of alloying elements in matrix were also beneficial for the improved corrosion resistance of T4 sample.Furthermore,the lower local strain energy in the matrix of T4 sample could also contribute to the excellent corrosion resistance.However,the precipitatedθphases in T6 sample were detrimental to further improve corrosion performance due to the reactivated micro-galvanic effect.At last,the main compositions of surface film on the three samples were also revealed in detail,attributing to the different corrosion resistance of three samples as well.
基金Project(51171209)supported by the National Natural Science Foundation of China
文摘The main methods of the second phase quantitative analysis in current material science researches are manual recognition and extracting by using software such as Image Tool and Nano Measurer. The weaknesses such as high labor intensity and low accuracy statistic results exist in these methods. In order to overcome the shortcomings of the current methods, the Ω phase in A1-Cu-Mg-Ag alloy is taken as the research object and an algorithm based on the digital image processing and pattern recognition is proposed and implemented to do the A1 alloy TEM （transmission electron microscope） digital images process and recognize and extract the information of the second phase in the result image automatically. The top-hat transformation of the mathematical morphology, as well as several imaging processing technologies has been used in the proposed algorithm. Thereinto, top-hat transformation is used for elimination of asymmetric illumination and doing Multi-layer filtering to segment Ω phase in the TEM image. The testing results are satisfied, which indicate that the Ω phase with unclear boundary or small size can be recognized by using this method. The omission of these two kinds of Ω phase can be avoided or significantly reduced. More Ω phases would be recognized （growing rate minimum to 2% and maximum to 400% in samples）, accuracy of recognition and statistics results would be greatly improved by using this method. And the manual error can be eliminated. The procedure recognizing and making quantitative analysis of information in this method is automatically completed by the software. It can process one image, including recognition and quantitative analysis in 30 min, but the manual method such as using Image Tool or Nano Measurer need 2 h or more. The labor intensity is effectively reduced and the working efficiency is greatly improved.
基金financially supported by the CITIC niobium steel development award Fund(M1656-2021)Central Iron and Steel Research Institute for its independent research and development fund(No.21G62460ZD).
文摘Increasing the hole expansion ratio is significant for developing high formability parts.Hole expansion tests were carried out on low carbon hot-rolled steel containing 0.11%Ti,0.072%Ti–0.03%Nb and 0.097%Ti–0.059%Nb,respectively.The effects of microstructure,texture,crack propagation behavior and second phase precipitation behavior on hole expansion ratio were investigated.The precipitation behavior of TiC and(Ti,Nb)C in austenite and ferrite in three groups of steel samples was calculated theoretically.The results showed that the hole expansion ratios of 0.11Ti,0.072Ti–0.03Nb and 0.097Ti–0.059Nb test steels were 51.73%,51.17%and 66.24%following simulated coiling at 600℃,respectively.The microstructure was mainly polygonal ferrite with a small amount of pearlite.The grain refinement of 0.097Ti–0.059Nb test steel and the low texture ratio of{110}//ND improved the hole expansion ratio.The low overall hole expansion ratio was due to the microstructure inhomogeneity.The microstructure uniformity was improved by the quenching and tempering treatment,and the hole expansion ratio of the three test steels was greatly increased.The fastest precipitation temperatures in the austenitic region of 0.11Ti,0.072Ti–0.03Nb and 0.097Ti–0.059Nb test steels were 880,860 and 830℃,while those in the ferrite region were 680,675 and 675℃,respectively.The addition of Nb element increased the volume free energy,so that the critical core size of the nucleation on the dislocation line increased,resulting in the decrease in the fastest precipitation temperature.
基金supported by the Outstanding Youth Fund of Yunnan Province(Grant No.202201AV070005)the National Natural Science Foundation of China(Grant No.52162029)+1 种基金the National Key R&D Program of China(Grant No.2022YFF0503804)the Yunnan Science and Technology Program(202401AT070403).
文摘The group Ⅳ–Ⅵ semiconductor,SnSe,is abundant on the earth and is a promising thermoelectric(TE)material due to its low thermal conductivity.However,the p-type SnSe polycrystals have low electrical conductivities due to their low carrier concentration,significantly limiting their further applications.This study introduced the argyrodite-type Ag_(9)GaSe_(6) compound into the SnSe matrix to effectively increase the hole carrier concentration,increasing the electrical conductivity.A high electrical conductivity of 50.5 S cm^(−1) was obtained for the SnSe+0.5 wt%Ag_(9)GaSe_(6) sample at 323 K.Due to the increased electrical conductivity,the SnSe+0.5 wt%Ag_(9)GaSe_(6) sample had an average power factor(PFave)value of~410μW m^(-1) K^(-2) in the 323–823 K temperature range,a nearly four times enhancement compared to the undoped SnSe sample.Additionally,the thermal conductivity slightly increased due to the introduction of the Ag_(9)GaSe_(6) compound.However,the electrical transport properties were significantly enhanced,making up for the improvement in thermal conductivity.Consequently,the SnSe+0.5 wt%Ag_(9)GaSe_(6) sample obtained a peak thermoelectric figure of merit ZT value of~1.2 at 823 K and a ZT_(ave) value of 0.58 in the 323–823 K temperature range.The proposed strategy improved the ZT and ZT_(ave) values of SnSe-based TE materials at room temperature and provided a systematic strategy for modifying SnSe-based TE materials.Moreover,the thermoelectric properties of SnSe can be effectively improved by introducing the Ag_(9)GaSe_(6) compound for doping,and waste heat power generation can be effectively carried out in the middle temperature region.
基金funded by the National Key Research and Development Program of China (Grant No. 2016YFB0301001 and 2016YFB0301101)Major Projects for Collaborative Innovation of Zhengzhou (Grant No.18XTZX12010)Certificate of Postdoctoral Research Grant in Henan Province (Grant No. 201903011)。
文摘Effect of the second phase in the micro-galvanic corrosion of a commercial Mg alloy containing rare earth elements, cast WE43 alloy,was investigated in 0.6 M NaCl solution and 0.6 M Na_(2)SO_(4)solution by scanning electron microscopy(SEM) observations, scanning Kelvin probe force microscopy(SKPFM) analysis, hydrogen evolution, weight loss measurement, and electrochemical techniques. It is confirmed that the second phase of cast WE43 alloy is more active than Mg matrix and exhibits an anodic role in the micro-galvanic corrosion with α-Mg matrix as cathode and dissolves preferentially in Na_(2)SO_(4)solution, in contrast to the situation in NaCl solution. The corrosion rate of cast WE43 alloy in Na_(2)SO_(4)solution is much higher than that in NaCl solution, which is different from the conventional wisdom and could be attributed to the different role of the second phase in the micro-galvanic corrosion in two solutions.
基金financial supports from the National Natural Science Foundation of China (Nos.51901068,51979099)the Key Research and Development Project of Jiangsu Province,China (No.BE2021027)+1 种基金the Opening Project of Jiangsu Key Laboratory of Advanced Structural Materials and Application Technology,China (No.ASMA202102)the Research Fund from Key Laboratory for Light-weight Materials of Jiangsu Province,China。
文摘To investigate the effect of separate Al_(2)Ca and Mg_(2)Ca phases on the corrosion properties of Mg−Al−Ca−Mn alloys,OM,SEM,immersion and electrochemical tests were conducted on the as-cast and ECAP Al_(2)Ca-containing(2Ca)and Mg_(2)Ca-containing(4Ca)alloys.At the beginning of corrosion,the two as-cast alloys are corroded slowly compared with ECAP alloys.With prolonging the corrosion time,the corrosion of ECAP alloys becomes slighter than that of as-cast alloys,which is mainly ascribed to the dispersion and refinement of the second phase in ECAP alloys.Moreover,the corrosion degree of 2Ca alloys is always slighter than that of 4Ca alloys,suggesting that Al_(2)Ca phase is more beneficial to the enhancement of corrosion resistance of Mg−Al−Ca−Mn based alloys than Mg_(2)Ca phase.Finally,based on the examinations of corrosion surface and electrochemical testing results,different corrosion mechanisms caused by the distributions and morphology of Al_(2)Ca and Mg_(2)Ca phases are discussed.
文摘The effect of equal-channel angular pressing(ECAP)processing at room temperature and 300℃on the distribution of the second phase particles and its influence on hardness and electrical conductivity of the commercial Cu-0.81Cr-0.07Zr alloy were investigated.Microstructural characterization indicated that the area fraction of coarse Cr-rich particles decreased after ECAP processing.This reduction was attributed to the Cr dissolution induced by plastic deformation.The electrical conductivity of the alloy decreased by 12%after 4 ECAP passes at room temperature due to the increase of electrons scattering caused by higher Cr content in solid solution and higher density of defects in the matrix.These results were supported by the reduction of the Cu lattice parameter and by the exothermic reactions,during differential scanning calorimetry(DSC)analysis,observed only in the samples subjected to ECAP processing.Aging heat treatment after ECAP processing promoted an additional hardening effect and the complete recuperation of the electrical conductivity,caused by the re-precipitation of the partially dissolved particles.The better combination of hardness(191 HV)and electrical conductivity(83.5%(IACS))was obtained after 4 ECAP passes at room temperature and subsequent aging at 380℃for 1 h.
基金financially supported by the National Natural Science Foundation of China (No. 51271206, No. 51571044)the National Basic Research Program of China (No. 2013CB632201)+1 种基金the Basic Research Project of Chongqing (cstc2015jcyj BX0081)National Key Research and Development Program (No. 2016YFB0301102)
文摘Microstructure evolution and damping capacities of Mg–Ce binary alloys with three different Ce contents（0.5, 1, or 2 wt%） have been systematically investigated in this work. Numerous fine parallel second phases in Mg–2Ce alloy are obtained, as well as a large number of dislocations around them, but few dislocations appear around the reticular second phase in the Mg–1Ce alloy. Among the three alloys, two internal friction peaks（P;and P;） are detected at about 78 and 167?C in both the Mg–0.5Ce and Mg–1Ce alloys.In addition, the alloy with special parallel second phase structure exhibits excellent damping capacity in both strain amplitude and temperature-dependent regions. These results may be ascribed to the stress concentration and the formation of abundant parallel and uniform dislocation configurations in the ?-Mg matrix without the influence of crystal orientation. The obtained results may provide a novel idea to prepare high-damping magnesium alloys by tailoring their microstructure.
基金financially supported by the National Key R&D Program of China (No. 2017YFB0306001)Guangxi Key Laboratory of Manufacturing System and Advanced Manufacturing Technology, China (No. 20-065-40-001k)。
文摘The morphology and size of second phase greatly influence the strengthening effect on oxidation dispersion strengthened Mo alloys.In this work,a novel nanostructuring strategy is adopted to modify the second phase of Y_(2)O_(3),and the corresponding effects of particle shape and size on mechanical properties of sintered Mo−Y_(2)O_(3) alloys were investigated.It is found that spherical particles with sizes below 200 nm are preferred due to the dominant intragranular distribution of second phases associated with better strengthening effect originating from dislocation pinning.With smaller particle size of Y_(2)O_(3) nanospheres(105 nm),the tensile strength of corresponding Mo alloy is enhanced by about 43.8%,much higher than that(8.3%)reinforced by second phase nanospheres with larger particle size(322 nm).Meanwhile,with similar particle size(around 100 nm),the spherical shape exhibits better strengthening effect than the one reinforced by one-dimensional rod-like second phase.
基金Item Sponsored by National Key Technology Research and Development Program in 11th Five-Year Plan of China (2006BE03A0)
文摘Two types of stress relaxation tests were carried out to investigate the incubation time for incipient precipi-tation of Ti（C,N） in deformed austenite and （Ti,Mo）C in ferrite of ferritic Ti-Mo microalloyed steel The size dis-tribution, amount and chemical composition of precipitates were obtained by using physicochemical phase analysis, and calculated according to thermodynamics and kinetics. The experimental results demonstrated that the incubation time was reduced with increasing Ti content, and prolonged with the addition of Mo. After 30 % deformation at 850 ℃, the nucleation of strain-induced Ti（C,N） was a relatively slow process. On the other hand, the temperature where the nucleation rate of （Ti, Mo）C in ferrite was the highest descended first and then ascended with increasing Ti content, and so did the temperature where the incubation time was the shortest. The key point is that the tempera-ture of steel containing about 0.09 % Ti is the lowest. The mass fraction of MC-type particles with size smaller than 10 nm in steel containing 0.09% Ti and 0.2% Mo reached 73.7%. The size distributions of precipitates in steel containing 0.09% Ti were relatively concentrated compared with that in steel containing 0.07% Ti.
基金supported by the National Natural Science Foundation of China(Nos.50571073,51574175 and 51474153)the Ph. D. Programs Foundation of Ministry of Education of China(20111402110004)the Natural Science Foundation of Shanxi Province(Nos.2009011028-3 and 2012011022-1)
文摘Alloys with composition of Mg_(96-x)Gd_3Zn_1Li_x(at.%)(x=0, 2, 4, and 6) were prepared by conventional casting. The microstructures of these alloys under as-cast and solid-solution conditions have been observed, and the mechanical properties were investigated. The results showed that Li is an effective element to refine the grains and break the eutectic networks in as-cast MgGd_3Zn_1 alloy. During solid solution treatment, these broken eutectic networks are spheroidized and highly dispersed. In addition, plentiful lamellar long period stacking ordered(LPSO) phases are precipitated in an α-Mg matrix when the Li addition is not more than 4%. Solid-solution treated Mg_(92)Gd_3Zn_1Li_4 alloy exhibits an optimal ultimate tensile strength(UTS) of 226 MPa and elongation of 5.8%. The strength of MgGd_3Zn_1 alloy is improved significantly, meanwhile, the toughness is apparently increased.
文摘The phase diagram of superaustenitic stainless steel 654SMO was calculated by thermodynamic software and the precipitated phases in the specimens aged at 800-1100°C for 1hwere studied by methods of physicochemical phase analysis,scanning electron microscopy and transmission electron microscopy.The results showed that the size of precipitated particles increased with increasing the temperature.The amount of second phases reached the maximum value at 900°C,but decreased above 900°C.There were about eight kinds of precipitated phases in 654SMO includingσphase,Cr_2N,μphase,χphase,Laves phase,M_（23）C_6,M_6C and M_3C,in which theσphase and Cr_2N were the dominant precipitated phases.
基金financially supported by the National Key Research and Development Program of China(No 2016YFB0700505)the China’s State Grid Corporation of Science and Technology Projects(No.SGRI-WD71-13-002)+1 种基金the National Natural Science Foundation of China(Nos.51571020 and 51371030)the Nationa High Technology Research and Development Program of China(No.2015AA034201)
文摘The selective abnormal growth of Goss grains in magnetic sheets of Fe-3%Si （grade Hi-B） induced by second-phase particles （AlN and MnS） was studied using a modified Monte Carlo Ports model. The starting microstructures for the simulations were generated from electron backscatter diffraction （EBSD） orientation imaging maps of recrystallized samples. In the simulation, second-phase particles were assumed to be randomly distributed in the initial microstructures and the Zener drag effect of particles on Goss grain boundaries was assumed to be selectively invalid because of the unique properties of Goss grain boundaries. The simulation results suggest that normal growth of the matrix grains stagnates because of the pinning effect of particles on their boundaries. During the onset of abnormal grain growth, some Goss grains with concave boundaries in the initial microstructure grow fast abnormally and other Goss grains with convex boundaries shrink and eventually disappear.
基金supported by the National Natural Science Foundation of China(Grant Nos.51174168,and 51274167)"111"Project,China(Grant No.B08040)
文摘The second phase particle effect on texture evolution of polycrystalline material is studied through phase-field method. A unique field variable is introduced into the phase-field model to represent the second phase particles. Elastic interaction between particles and grains is also considered. Results indicate that in the presence of second phase particles the average particle diameter turns smaller than in the absence of these particles and retards texture formation by pinning effect. The second phase particles change the strain energy profile, which tremendously influences the pinning effect.
文摘The second phase particle dispersed in microalloyed steel has different effects on grain growth depending on their size and volume fiaction of the second phase particles which will change during welding thermal cycles. The particle coarsening and dissolution kinetics model was analyzed for continuous heating and cooling. In addition, based on experimental data, the coupled equation of grain growth was established by introducing limited size of grain growth with the consideration of the second phase particles pinning effects. Using Monte Carlo method based on experimental data model, the grain growth simulation for heat-affected zone of microalloyed steel welds was achieved. The calculating results were well in agreement with that of experiments.
基金the financial support from the National Natural Science Foundation of China(Grant No.51105328)the Natural Science Foundation of Jiangsu Province of China(No.BK20130447)the Colleges and Universities in Jiangsu Province Natural Science Foundation of China(Grant No.13KJB430026)
文摘In order to control the grain size during hot forming,grain growth behavior of a pre-extruded Mg-6Zn magnesium alloy and its correlation with solute and second phase distribution were investigated.Isothermal annealing was conducted on a Gleeble-1500 thermo-mechanical simulator.The mean grain size Dg of each annealed specimen was measured by the quantitative metallography technique.The grain growth kinetics of the Mg-6Zn alloy annealed at 473-623 K was obtained as Dg^4- Dg0^4=2.25 ×10^11 exp（-95450）by the least square linear regression method.The deviation of grain growth exponent n = 4 from the theoretical value of 2 may be attributed to the presence of solute zinc and second phases which will retard the boundary migration.Microscopic observations show that the non-uniform distribution of grain size for samples pre-extruded or annealed at low temperatures is closely related to the non-uniform distribution of fine and dispersed second phases but not to the non-uniform distribution of solute zinc.This indicates that second phase pinning effect plays an important role in microstructure refinement.
