Full scale experimental study on nitrogen removal for low-carbon wastewater was conducted in reversed A2/O process in Jiguanshi waste water treatment plant in Chongqing,in order to aid the operation and maintenance of...Full scale experimental study on nitrogen removal for low-carbon wastewater was conducted in reversed A2/O process in Jiguanshi waste water treatment plant in Chongqing,in order to aid the operation and maintenance of similar WWTP. When the proposed measures,such as using 0.1% (volume fraction of wastewater) landfill leachate,shortening HRT by 2/3 in the primary sedimentation tank and controlling DO at 0.5 mg/L in the 3rd section of aerobic zone,are applied,15% of the carbon source can be complemented,the favorable property of activated sludge is achieved,and the nitrogen removal effect is significantly improved. The effluent NH3-N is 2 mg/L and the removal rate is 90%. The effluent TN is 17 mg/L and the removal rate is 54%. The up-to-standard discharge of the effluent is achieved. And after the optimization,the unit electricity consumption also reaches 0.21 kW/h and saves 20%.展开更多
This study evaluated the removal of multiple pollutants,i.e.,polybrominated diphenyl ethers(PBDEs),novel halogenated flame retardants(HFRs),sulfonamide antibiotics(SAs),and heavy metals(HMs),by a fullscale reversed A^...This study evaluated the removal of multiple pollutants,i.e.,polybrominated diphenyl ethers(PBDEs),novel halogenated flame retardants(HFRs),sulfonamide antibiotics(SAs),and heavy metals(HMs),by a fullscale reversed A^(2)/O process in a sewage treatment plant(STP)in Guangzhou,China.The reversed A^(2)/O process demonstrated high removal efficiencies(REs)for total PBDEs(60.5%±4.3%),novel HFRs(98.4%±2.8%)and HMs(70.1%±1.2%),and a relatively low RE for SAs(25.0%±2.3%).BDE 209,the dominant PBDE congener,showed a high residual concentration(13.41±5.18 ng/L)in the suspended particulate matter(SPM)of treated effluents.So me novel HFRs,dechlorane plus(DP)and decabromodiphe nyl ethane(DBDPE),were detected in the SPM of the raw sewage(7.50±4.14 ng/L and 11.52±11.65 ng/L,respectively).The removal ofSAs was mainly through biodegradation in the activated sludge bioreactors(ASBs).Ofthe HMs,Mn and Ni exhibited the lowest REs(47.5%±2.2%and 35.0%±2.6%,respectively),while Cr and Cu showed the highest removal(REs>80%).In terms of treatment units in the reversed A^(2)/O process,ASBs showed the highest RE(27.8%)for the multiple pollutants.The information can aid in our understanding of removal properties of STPs on various pollutants and evaluating the ecological/health risks of STPs as point pollutant sources.展开更多
Electrochromic(EC)smart windows utilizing a reversible metal electrodeposition device(RMED)offer a compelling alternative for dynamically regulating transmissions of optical and thermal energy.An EC device(ECD)is cons...Electrochromic(EC)smart windows utilizing a reversible metal electrodeposition device(RMED)offer a compelling alternative for dynamically regulating transmissions of optical and thermal energy.An EC device(ECD)is constructed by reversible metal electrodeposition(RME)of Bi/Cu on WO_(3)·xH_(2)O film electrodeposited onto fluorine-doped tin oxide(FTO)transparent conductive glass.The electrolyte consists of CuCl_(2),BiCl_(3),KCl and HCl aqueous solution,supplying necessary components for both electrochemical and electrodeposition processes.The ECD shows ability to rapidly transition between colorless and black states,which achieves a large optical modulation of 77.0%at 570 nm.In the black state,the ECD exhibits a near-zero transmittance in the wavelength range of 400-1100 nm while maintaining 96.6%of its initial optical modulation after coloration/bleaching cycling of 60000 s,exhibiting good cyclic stability.This RMED has relatively high stability under open-circuit voltage and also possesses excellent heat insulation performance.The results offer a solution to overcome the poor cyclic stability of RMEDs and improve the optical modulation of ECDs.展开更多
The morphology and the formation of Y2BaCuO5 phase in powder melting processed YBa2Cu3O7-x superconductors were investigated. The experimental results show the heat treatment can not change the shape of Y2BaCuO5 parti...The morphology and the formation of Y2BaCuO5 phase in powder melting processed YBa2Cu3O7-x superconductors were investigated. The experimental results show the heat treatment can not change the shape of Y2BaCuO5 particles in powder melting processed samples. The formation of round Y2BaCuO5 phase is due to relative content of each constitution of precursor powders in powder melting process. For powder melting process, the excessive liquid phase is eliminated, which restrains the preferred growth of Y2BaCuO5 particles.展开更多
The ultrafine powders of YBa2Cu3O7-x with the size of 100nm were synthesized by Sol-Gel process using cit-rate as complex and ammonium hydroxide to adjust pH of solu-tion. The process of Sol formation and Gel polymeri...The ultrafine powders of YBa2Cu3O7-x with the size of 100nm were synthesized by Sol-Gel process using cit-rate as complex and ammonium hydroxide to adjust pH of solu-tion. The process of Sol formation and Gel polymerization of YBa2Cu3O7-x in the Sol-Gel synthetic reaction has bee studied. The particle size ,pruity, sintering activity and superconducting properties of YBa2Cu3O7-x prepared by Sol-Gel method are better than by solid state reaction.展开更多
YBa2Cu3O7-δ-Agx composite superconductors were prepared by hybrid sintering process using YBa2Cu3O7-δ-Agx ultrafine powder and Ag2O finepower, which were prepared by sol-gel process and precipitation process respect...YBa2Cu3O7-δ-Agx composite superconductors were prepared by hybrid sintering process using YBa2Cu3O7-δ-Agx ultrafine powder and Ag2O finepower, which were prepared by sol-gel process and precipitation process respectively. The effect of the Ag content on superconducting crictical transition temperature of YBa2Cu3O7-δ-Agx was not evident as long as YBa2Cu3O7-δ-Agx can form continuous network. But Ag can increase superconduction crictical current and density of the composite superconductors. The normal state (i.e. non-superconducting state at room temperature) resistivity shows a percolation threshold at 20%-30% Ag, whereas the superconducting net-work shows a percolationthreshold at 70% -80% Ag.展开更多
In-situ HVEM observation on phase transition of the YBa_2Cu_3O_(7-x) superconducting compound in pro- cess of heating was carried out,and high temperature X-ray diffraction analysis in air and X-ray diffraction phase ...In-situ HVEM observation on phase transition of the YBa_2Cu_3O_(7-x) superconducting compound in pro- cess of heating was carried out,and high temperature X-ray diffraction analysis in air and X-ray diffraction phase analysis for the sample treated in vacuum condition were made.The results showed that the temperature of phase transition is related to oxygen content in the sample and in general,is 100℃ to 120℃ lower in vacu- um condition than in air.At 320℃ to 350℃ twin bands begin to disappear,and some Cu_2O are formed on the surface of the sample and transit from orthorhombic YBa_2Cu_3O_(7-x) to arthorhombic Y_2BaCuO_5 compound. This transition was completed at about 500℃.Above 900℃,this compound consists of the Y_2BaCuO_5, BaCuO_2,Y_2O_3 and some other minor compounds.No phase transition was observed during cooling the sample.展开更多
The deformation behaviors of Al2O3/Al composites were investigated by compressive tests conducted at temperature of 300-450 °C and strain rates of 0.001-1.0 s-1 with Gleeble-1500 D thermal simulator system. The r...The deformation behaviors of Al2O3/Al composites were investigated by compressive tests conducted at temperature of 300-450 °C and strain rates of 0.001-1.0 s-1 with Gleeble-1500 D thermal simulator system. The results show that the flow stress increases with increasing strain rate and decreasing temperature. The hyperbolic sine constitutive equation can describe the flow stress behavior of Al2O3/Al composites, and the deformation activation energy and constitutive equations were calculated. The processing maps of Al2O3/Al-2 μm and Al2O3/Al-1 μm composites at strain of 0.6 were obtained and the optimum processing domains are in ranges of 300-330 °C, 0.007-0.03 s-1 and 335-360 °C, 0.015-0.06 s-1 for hot working, respectively. The instability zones of flow behavior can also be recognized by the maps.展开更多
The layered Li[Ni1/3Mn1/3Co1/3]O2 was separately synthesized by pretreatment process of ball mill method and solution phase route, using [Ni1/3Co1/3Mn1/3]3O4 and lithium hydroxide as raw materials. The physical and el...The layered Li[Ni1/3Mn1/3Co1/3]O2 was separately synthesized by pretreatment process of ball mill method and solution phase route, using [Ni1/3Co1/3Mn1/3]3O4 and lithium hydroxide as raw materials. The physical and electrochemical behaviors of Li[Ni1/3Mn1/3Co1/3]O2 were characterized by X-ray diffraction （XRD）, scanning electron microscopy （SEM）, field emission scanning electron microscopy （FESEM） and electrochemical charge/discharge cycling tests. The results show that the difference in pretreatment process results in the difference in compound Li[Ni1/3Co1/3Mn1/3]O2 structure, morphology and the electrochemical characteristics. The Li[Ni1/3Mn1/3Co1/3]O2 prepared by solution phase route maintains the uniform spherical morphology of the [Ni1/3Co1/3Mn1/3]3O4, and it exhibits a higher capacity retention and better rate capability than that prepared by ball mill method. The initial discharge capacity of this sample reaches 178 mA-h/g and the capacity retention after 50 cycles is 98.7% at a current density of 20 mA/g. Moreover, it delivers high discharge capacity of 135 mA-h/g at a current density of 1 000 mA/g.展开更多
Two full-scale systems operated in parallel, a conventional A2/O system consisting of anaerobic, anoxic and oxic compartments in succession and an inverted system consisting of anoxic, anaerobic and oxic compartments ...Two full-scale systems operated in parallel, a conventional A2/O system consisting of anaerobic, anoxic and oxic compartments in succession and an inverted system consisting of anoxic, anaerobic and oxic compartments without internal recycle, were compared in terms of their phosphorus removal performance, with an emphasis on phosphate （P） release behaviors, using both operational data and simulation results. The inverted system exhibited better long-term phosphorus removal performance （0.2 ± 0.3 vs. 0.7 ±0.7 mg/L）, which should be attributed to the higher P release rate （0.79 vs. 0.60 kg P/（kg MLSS.day）） in the non-aerated compartments. The P release occurred in both the anoxic and anaerobic compartments of the inverted system, resulting in more efficient P release. Although the abundances of the ＇Candidatus Accumulibacter phosphatis＇ population in the two systems were quite similar （（19.1 ＋ 3.27）% and （18.4 ＋ 4.15）% of the total microbe （DAPI stained particles） population in the inverted and conventional systems, respectively, by fluorescence in situ hybridization （FISH））, the high-concentration DAPI staining results show that the abundances of the whole polyphosphate accumulating organisms （PAOs） in the aerobic ends were quite different （the average ratios of the poly-P granules to total microbes （DAPI stained particles） were （45 ±4.18）% and （35 ± 5.39）%, respectively）. Both the operational data and simulation results showed that the inverted system retained more abundant PAO populations due to its special configuration, which permitted efficient P release in the non-aerated compartment and better P removal,展开更多
The degradation of formaldehyde gas was studied using UV/TiO2/O3 process under the condition of continuous flow mode. The effects of humidity, initial formaldehyde concentration, residence time and ozone adding amount...The degradation of formaldehyde gas was studied using UV/TiO2/O3 process under the condition of continuous flow mode. The effects of humidity, initial formaldehyde concentration, residence time and ozone adding amount on degradation of formaldehyde gas were investigated. The experimental results indicated that the combination of ozonation with photocatalytic oxidation on the degradation of formaldehyde showed a synergetic action, e.g,, it could considerably increase decomposing of formaldehyde. The degradation efficiency of formaldehyde was between 73.6% and 79.4% while the initial concentration in the range of 1.84--24 mg/m^3 by O3/TiO2flJV process. The optimal humidity was about 50% in UV/TiO2/O3 processs and degradation of formaldehyde increases from 39.0% to 94.1% when the ozone content increased from 0 to 141 mg/m^3. Furthermore, the kinetics of formaldehyde degradation reaction could be described by Langmuir-Hinshelwood model. The rate constant k of 46.72 mg/（m^3.min） and Langmuir adsorption coefficient K of 0.0268 m^3/mg were obtained.展开更多
A lab-scale anaerobic-anoxic-oxic (A2O) process used to treat a synthetic brewage wastewater was investigated. The objectives of the study were to identify the existence of denitrifying phosphorus removing bacteria (D...A lab-scale anaerobic-anoxic-oxic (A2O) process used to treat a synthetic brewage wastewater was investigated. The objectives of the study were to identify the existence of denitrifying phosphorus removing bacteria (DPB), evaluate the contribution of DPB to biological nutrient removal and enhance the denitrifying phosphorus removal in A2O bioreactors. Sludge analysis confirmed that the average anoxic P uptake accounted for approximately 70% the total amount of P uptake, and the ratio of anoxic P uptake rate to aerobic P uptake rate was 69%. In addition, nitrate concentration in the anoxic phase and different organic substrate introduced into the anaerobic phase had significant effect on the anoxic P uptake. Compared with conventional A2O processes, good removal efficiencies of COD, phosphorus, ammonia and total nitrogen (92.3%, 95.5%, 96% and 79.5%, respectively) could be achieved in the anoxic P uptake system, and aeration energy consumption was saved 25%. By controlling the nitrate recirculation flow in the anoxic zone, anoxic P uptake could be enhanced, which solved the competition for organic substrates among poly-P organisms and denitrifiers successfully under the COD limiting conditions. Therefore, in wastewater treatment plants the control system should be applied according to the practical situation to optimize the operation.展开更多
Traditional O3-type Li-rich layered materials are attractive with ultra-high specific capacities,but suffering from inherent problems of voltage hysteresis and poor cycle performance.As an alternative,O2-type material...Traditional O3-type Li-rich layered materials are attractive with ultra-high specific capacities,but suffering from inherent problems of voltage hysteresis and poor cycle performance.As an alternative,O2-type materials show the potential to improve the oxygen redox reversibility and structural stability.However,their structure-performance relationship is still unclear.Here,we investigate the correlation between the Li component and dynamic chemical reversibility of O2-type Li-rich materials.By exploring the formation mechanism of a series of materials prepared by Na/Li exchange,we reveal that insufficient Li leads to an incomplete replacement,and the residual Na in the Li-layer would hinder the fast diffusion of Li^(+).Moreover,excessive Li induces the extraction of interlayer Li during the melting chemical reaction stage,resulting in a reduction in the valence of Mn,which leads to a severe Jahn-Teller effect.Structural detection confirms that the regulation of Li can improve the cycle stability of Li-rich materials and suppress the trend of voltage fading.The reversible phase evolution observed in in-situ X-ray diffraction confirms the excellent structural stability of the optimized material,which is conducive to capacity retention.This work highlights the significance of modulating dynamic electrochemical performance through the intrinsic structure.展开更多
基金Project (2009ZX07315-002-01) supported by Water Pollution Control and Management of Major Special Science and Technology
文摘Full scale experimental study on nitrogen removal for low-carbon wastewater was conducted in reversed A2/O process in Jiguanshi waste water treatment plant in Chongqing,in order to aid the operation and maintenance of similar WWTP. When the proposed measures,such as using 0.1% (volume fraction of wastewater) landfill leachate,shortening HRT by 2/3 in the primary sedimentation tank and controlling DO at 0.5 mg/L in the 3rd section of aerobic zone,are applied,15% of the carbon source can be complemented,the favorable property of activated sludge is achieved,and the nitrogen removal effect is significantly improved. The effluent NH3-N is 2 mg/L and the removal rate is 90%. The effluent TN is 17 mg/L and the removal rate is 54%. The up-to-standard discharge of the effluent is achieved. And after the optimization,the unit electricity consumption also reaches 0.21 kW/h and saves 20%.
基金the National Natural Science Foundation of China(No.91851110)Guangzhou University’s 2017 Training Program for Young Top-Notch Personnels(No.BJ201713)+1 种基金Scientific Research Project of Guangzhou University(No.YK2020017)Guizhou Provincial Department of Education Youth Science and Technology Talents Growth Project(No.KY[2017]300)。
文摘This study evaluated the removal of multiple pollutants,i.e.,polybrominated diphenyl ethers(PBDEs),novel halogenated flame retardants(HFRs),sulfonamide antibiotics(SAs),and heavy metals(HMs),by a fullscale reversed A^(2)/O process in a sewage treatment plant(STP)in Guangzhou,China.The reversed A^(2)/O process demonstrated high removal efficiencies(REs)for total PBDEs(60.5%±4.3%),novel HFRs(98.4%±2.8%)and HMs(70.1%±1.2%),and a relatively low RE for SAs(25.0%±2.3%).BDE 209,the dominant PBDE congener,showed a high residual concentration(13.41±5.18 ng/L)in the suspended particulate matter(SPM)of treated effluents.So me novel HFRs,dechlorane plus(DP)and decabromodiphe nyl ethane(DBDPE),were detected in the SPM of the raw sewage(7.50±4.14 ng/L and 11.52±11.65 ng/L,respectively).The removal ofSAs was mainly through biodegradation in the activated sludge bioreactors(ASBs).Ofthe HMs,Mn and Ni exhibited the lowest REs(47.5%±2.2%and 35.0%±2.6%,respectively),while Cr and Cu showed the highest removal(REs>80%).In terms of treatment units in the reversed A^(2)/O process,ASBs showed the highest RE(27.8%)for the multiple pollutants.The information can aid in our understanding of removal properties of STPs on various pollutants and evaluating the ecological/health risks of STPs as point pollutant sources.
文摘Electrochromic(EC)smart windows utilizing a reversible metal electrodeposition device(RMED)offer a compelling alternative for dynamically regulating transmissions of optical and thermal energy.An EC device(ECD)is constructed by reversible metal electrodeposition(RME)of Bi/Cu on WO_(3)·xH_(2)O film electrodeposited onto fluorine-doped tin oxide(FTO)transparent conductive glass.The electrolyte consists of CuCl_(2),BiCl_(3),KCl and HCl aqueous solution,supplying necessary components for both electrochemical and electrodeposition processes.The ECD shows ability to rapidly transition between colorless and black states,which achieves a large optical modulation of 77.0%at 570 nm.In the black state,the ECD exhibits a near-zero transmittance in the wavelength range of 400-1100 nm while maintaining 96.6%of its initial optical modulation after coloration/bleaching cycling of 60000 s,exhibiting good cyclic stability.This RMED has relatively high stability under open-circuit voltage and also possesses excellent heat insulation performance.The results offer a solution to overcome the poor cyclic stability of RMEDs and improve the optical modulation of ECDs.
基金Funded by the National Natural Science Foundation of China (50432050)the National High Technology Research and Development Program of China(2007AA03Z241)
文摘The morphology and the formation of Y2BaCuO5 phase in powder melting processed YBa2Cu3O7-x superconductors were investigated. The experimental results show the heat treatment can not change the shape of Y2BaCuO5 particles in powder melting processed samples. The formation of round Y2BaCuO5 phase is due to relative content of each constitution of precursor powders in powder melting process. For powder melting process, the excessive liquid phase is eliminated, which restrains the preferred growth of Y2BaCuO5 particles.
文摘The ultrafine powders of YBa2Cu3O7-x with the size of 100nm were synthesized by Sol-Gel process using cit-rate as complex and ammonium hydroxide to adjust pH of solu-tion. The process of Sol formation and Gel polymerization of YBa2Cu3O7-x in the Sol-Gel synthetic reaction has bee studied. The particle size ,pruity, sintering activity and superconducting properties of YBa2Cu3O7-x prepared by Sol-Gel method are better than by solid state reaction.
文摘YBa2Cu3O7-δ-Agx composite superconductors were prepared by hybrid sintering process using YBa2Cu3O7-δ-Agx ultrafine powder and Ag2O finepower, which were prepared by sol-gel process and precipitation process respectively. The effect of the Ag content on superconducting crictical transition temperature of YBa2Cu3O7-δ-Agx was not evident as long as YBa2Cu3O7-δ-Agx can form continuous network. But Ag can increase superconduction crictical current and density of the composite superconductors. The normal state (i.e. non-superconducting state at room temperature) resistivity shows a percolation threshold at 20%-30% Ag, whereas the superconducting net-work shows a percolationthreshold at 70% -80% Ag.
文摘In-situ HVEM observation on phase transition of the YBa_2Cu_3O_(7-x) superconducting compound in pro- cess of heating was carried out,and high temperature X-ray diffraction analysis in air and X-ray diffraction phase analysis for the sample treated in vacuum condition were made.The results showed that the temperature of phase transition is related to oxygen content in the sample and in general,is 100℃ to 120℃ lower in vacu- um condition than in air.At 320℃ to 350℃ twin bands begin to disappear,and some Cu_2O are formed on the surface of the sample and transit from orthorhombic YBa_2Cu_3O_(7-x) to arthorhombic Y_2BaCuO_5 compound. This transition was completed at about 500℃.Above 900℃,this compound consists of the Y_2BaCuO_5, BaCuO_2,Y_2O_3 and some other minor compounds.No phase transition was observed during cooling the sample.
基金Project(2012AA030311)supported by the National High-tech Research and Development Program of ChinaProject(2010BB4074)supported by the Natural Science Foundation of Chongqing Municipality,ChinaProject(2010ZD-02)supported by the State Key Laboratory for Advanced Metals and Materials,China
文摘The deformation behaviors of Al2O3/Al composites were investigated by compressive tests conducted at temperature of 300-450 °C and strain rates of 0.001-1.0 s-1 with Gleeble-1500 D thermal simulator system. The results show that the flow stress increases with increasing strain rate and decreasing temperature. The hyperbolic sine constitutive equation can describe the flow stress behavior of Al2O3/Al composites, and the deformation activation energy and constitutive equations were calculated. The processing maps of Al2O3/Al-2 μm and Al2O3/Al-1 μm composites at strain of 0.6 were obtained and the optimum processing domains are in ranges of 300-330 °C, 0.007-0.03 s-1 and 335-360 °C, 0.015-0.06 s-1 for hot working, respectively. The instability zones of flow behavior can also be recognized by the maps.
基金Project(20871101)supported by the National Natural Science Foundation of ChinaProject(2009WK2007)supported by Key Project of Science and Technology Department of Hunan Province,ChinaProject(CX2009B133)supported by Colleges and Universities in Hunan Province Plans to Graduate Research and Innovation,China
文摘The layered Li[Ni1/3Mn1/3Co1/3]O2 was separately synthesized by pretreatment process of ball mill method and solution phase route, using [Ni1/3Co1/3Mn1/3]3O4 and lithium hydroxide as raw materials. The physical and electrochemical behaviors of Li[Ni1/3Mn1/3Co1/3]O2 were characterized by X-ray diffraction （XRD）, scanning electron microscopy （SEM）, field emission scanning electron microscopy （FESEM） and electrochemical charge/discharge cycling tests. The results show that the difference in pretreatment process results in the difference in compound Li[Ni1/3Co1/3Mn1/3]O2 structure, morphology and the electrochemical characteristics. The Li[Ni1/3Mn1/3Co1/3]O2 prepared by solution phase route maintains the uniform spherical morphology of the [Ni1/3Co1/3Mn1/3]3O4, and it exhibits a higher capacity retention and better rate capability than that prepared by ball mill method. The initial discharge capacity of this sample reaches 178 mA-h/g and the capacity retention after 50 cycles is 98.7% at a current density of 20 mA/g. Moreover, it delivers high discharge capacity of 135 mA-h/g at a current density of 1 000 mA/g.
基金supported by the National Natural Science Foundation of China (No. 20921140094)the Knowledge Innovation Project of Chinese Academy of Sciences(No. KSCX2-YW-G-054)
文摘Two full-scale systems operated in parallel, a conventional A2/O system consisting of anaerobic, anoxic and oxic compartments in succession and an inverted system consisting of anoxic, anaerobic and oxic compartments without internal recycle, were compared in terms of their phosphorus removal performance, with an emphasis on phosphate （P） release behaviors, using both operational data and simulation results. The inverted system exhibited better long-term phosphorus removal performance （0.2 ± 0.3 vs. 0.7 ±0.7 mg/L）, which should be attributed to the higher P release rate （0.79 vs. 0.60 kg P/（kg MLSS.day）） in the non-aerated compartments. The P release occurred in both the anoxic and anaerobic compartments of the inverted system, resulting in more efficient P release. Although the abundances of the ＇Candidatus Accumulibacter phosphatis＇ population in the two systems were quite similar （（19.1 ＋ 3.27）% and （18.4 ＋ 4.15）% of the total microbe （DAPI stained particles） population in the inverted and conventional systems, respectively, by fluorescence in situ hybridization （FISH））, the high-concentration DAPI staining results show that the abundances of the whole polyphosphate accumulating organisms （PAOs） in the aerobic ends were quite different （the average ratios of the poly-P granules to total microbes （DAPI stained particles） were （45 ±4.18）% and （35 ± 5.39）%, respectively）. Both the operational data and simulation results showed that the inverted system retained more abundant PAO populations due to its special configuration, which permitted efficient P release in the non-aerated compartment and better P removal,
基金Project supported by the Science Project of Harbin City(No. H2001-12)the Youth Foundation of School of Municipal and Environmental Engineering in Harbin Institute of Technology(No. 01306914).
文摘The degradation of formaldehyde gas was studied using UV/TiO2/O3 process under the condition of continuous flow mode. The effects of humidity, initial formaldehyde concentration, residence time and ozone adding amount on degradation of formaldehyde gas were investigated. The experimental results indicated that the combination of ozonation with photocatalytic oxidation on the degradation of formaldehyde showed a synergetic action, e.g,, it could considerably increase decomposing of formaldehyde. The degradation efficiency of formaldehyde was between 73.6% and 79.4% while the initial concentration in the range of 1.84--24 mg/m^3 by O3/TiO2flJV process. The optimal humidity was about 50% in UV/TiO2/O3 processs and degradation of formaldehyde increases from 39.0% to 94.1% when the ozone content increased from 0 to 141 mg/m^3. Furthermore, the kinetics of formaldehyde degradation reaction could be described by Langmuir-Hinshelwood model. The rate constant k of 46.72 mg/（m^3.min） and Langmuir adsorption coefficient K of 0.0268 m^3/mg were obtained.
基金Supported by Key Technology Research and Development Program of the Tenthfive-year plan (2001BA610A-09), the NationalNatural Science Foundation of China (No. 50478040) and 863 Hi-Technology Research and Development Program of China(No.2004AA601020)
文摘A lab-scale anaerobic-anoxic-oxic (A2O) process used to treat a synthetic brewage wastewater was investigated. The objectives of the study were to identify the existence of denitrifying phosphorus removing bacteria (DPB), evaluate the contribution of DPB to biological nutrient removal and enhance the denitrifying phosphorus removal in A2O bioreactors. Sludge analysis confirmed that the average anoxic P uptake accounted for approximately 70% the total amount of P uptake, and the ratio of anoxic P uptake rate to aerobic P uptake rate was 69%. In addition, nitrate concentration in the anoxic phase and different organic substrate introduced into the anaerobic phase had significant effect on the anoxic P uptake. Compared with conventional A2O processes, good removal efficiencies of COD, phosphorus, ammonia and total nitrogen (92.3%, 95.5%, 96% and 79.5%, respectively) could be achieved in the anoxic P uptake system, and aeration energy consumption was saved 25%. By controlling the nitrate recirculation flow in the anoxic zone, anoxic P uptake could be enhanced, which solved the competition for organic substrates among poly-P organisms and denitrifiers successfully under the COD limiting conditions. Therefore, in wastewater treatment plants the control system should be applied according to the practical situation to optimize the operation.
基金the National Natural Science Foundation of China(21673064 and 51902072)the Heilongjiang Touyan Team(HITTY-20190033)+2 种基金the Fundamental Research Funds for the Central Universities(HIT.NSRIF.2019040 and 2019041)the State Key Laboratory of Urban Water Resource and Environment(Harbin Institute of Technology)(2020 DX11)the Heilongjiang postdoctoral financial assistance(LBH-Z19055)。
文摘Traditional O3-type Li-rich layered materials are attractive with ultra-high specific capacities,but suffering from inherent problems of voltage hysteresis and poor cycle performance.As an alternative,O2-type materials show the potential to improve the oxygen redox reversibility and structural stability.However,their structure-performance relationship is still unclear.Here,we investigate the correlation between the Li component and dynamic chemical reversibility of O2-type Li-rich materials.By exploring the formation mechanism of a series of materials prepared by Na/Li exchange,we reveal that insufficient Li leads to an incomplete replacement,and the residual Na in the Li-layer would hinder the fast diffusion of Li^(+).Moreover,excessive Li induces the extraction of interlayer Li during the melting chemical reaction stage,resulting in a reduction in the valence of Mn,which leads to a severe Jahn-Teller effect.Structural detection confirms that the regulation of Li can improve the cycle stability of Li-rich materials and suppress the trend of voltage fading.The reversible phase evolution observed in in-situ X-ray diffraction confirms the excellent structural stability of the optimized material,which is conducive to capacity retention.This work highlights the significance of modulating dynamic electrochemical performance through the intrinsic structure.
