A dual-bed reactor was constructed comprising of a 5%Na2WO4-2%Mn/SiO2 particle catalyst and a 4%Ce-5%Na2WO4-2%Mn/SiO2 /cordierite monolithic catalyst.The reaction performance of the oxidative coupling of methane （OCM...A dual-bed reactor was constructed comprising of a 5%Na2WO4-2%Mn/SiO2 particle catalyst and a 4%Ce-5%Na2WO4-2%Mn/SiO2 /cordierite monolithic catalyst.The reaction performance of the oxidative coupling of methane （OCM） over the dual-bed reactor system was evaluated.The effects of the bed height and operation mode,as well as the reaction parameters such as reaction temperature,CH4/O2 ratio and flowrate of feed gas,on the catalytic performance were investigated.The results indicated that the suggested dual-bed reactor exhibited a good performance for the OCM reaction when the feed gases firstly passed through the particle catalyst bed and then to the monolithic catalyst bed.A CH4 conversion of 38.2% and a C2H4 selectivity of 43.3% could be obtained using the dual-bed reactor with a particle catalyst bed height of 10 mm and a monolithic catalyst bed height of 50 mm.Both the CH4 conversion and C2H4 selectivity have increased by 2.5% and 12.8%,respectively,as compared with the 5%Na2WO4-2%Mn/SiO2 particle catalyst in a conventional single-bed reactor and by 12.9% and 23.0%,respectively,as compared with the 4%Ce-5%Na2WO4-2%Mn/SiO2 /cordierite monolithic catalyst in a single-bed reactor.The catalytic performance of the OCM in the dual-bed reactor system has been improved remarkably.展开更多
A three-dimensional geometric model was set up for the oxidative coupling of methane(OCM) fixed bed reactor loaded with Na_3PO_4-Mn/SiO_2/cordierite monolithic catalyst,and an improved Stansch kinetic model was establ...A three-dimensional geometric model was set up for the oxidative coupling of methane(OCM) fixed bed reactor loaded with Na_3PO_4-Mn/SiO_2/cordierite monolithic catalyst,and an improved Stansch kinetic model was established to calculate the OCM reactions using the computational fluid dynamics method and Fluent software.The simulation conditions were completely the same with the experimental conditions that the volume velocity of the reactant is 80 ml·min^(-1) under standard state,the CH_4/O_2 ratio is 3 and the temperature and pressure is800 ℃ and 1 atm,respectively.The contour of the characteristic parameters in the catalyst bed was analyzed,such as the species mass fractions,temperature,the heat flux on side wall surface,pressure,fluid density and velocity.The results showed that the calculated values matched well with the experimental values on the conversion of CH4 and the selectivity of products(C_2H_6,C_2H_4,CO,CO_2 and H_2) in the reactor outlet with an error range of±4%.The mass fractions of CH_4 and O_2 decreased from 0.600 and 0.400 at the catalyst bed inlet to 0.445 and0.120 at the outlet,where the mass fractions of C_2H_6,C_2H_4,CO and CO_2 were 0.0245,0.0460,0.0537 and 0.116,respectively.Due to the existence of laminar boundary layer,the mass fraction contours of each species bent upwards in the vicinity of the boundary layer.The volume of OCM reaction was changing with the proceeding of reaction,and the total moles of products were greater than reactants.The flow field in the catalyst bed maintained constant temperature and pressure.The fluid density decreased gradually from 2.28 kg·m^(-3) at the inlet of the catalyst bed to 2.18 kg·m^(-3) at the outlet of the catalyst bed,while the average velocity magnitude increased from 0.108 m·s-1 to 0.120 m·s^(-1).展开更多
A solution of 0.1 mol/L to 1.0 mol/L H2SO4 can dissolve alkali metals and alkaline earth metals which weaken an active site of SCR catalyst. The waste catalyst washed with 0.5 mol/L H2SO4 regained the best catalytic a...A solution of 0.1 mol/L to 1.0 mol/L H2SO4 can dissolve alkali metals and alkaline earth metals which weaken an active site of SCR catalyst. The waste catalyst washed with 0.5 mol/L H2SO4 regained the best catalytic activity. When a concentration of the sulfuric acid is less than 0.5 mol/L, sufficient cleaning effects cannot be obtained. In contrast, when the concentration is greater than 1.0 tool/L, the active components, vanadium and tungsten are undesirably eluted. The total BET surface of the catalyst regenerated by air lift loop reactor showed almost the same as that of fresh catalyst due to the removal of insoluble compounds which may be penetrated into pores of catalyst. The addition of a solution of 0.075 mol/L ammonium vanadate （NHnVO3） and 0.075 mol/L ammonium paratungstate （5（NH4）20· 12WO3-5H20） to 0.1 mol/L H2SO4 significantly increases the activity of the waste catalyst.展开更多
An industrial scale propylene production via oxidative dehydrogenation of propane （ODHP） in multi-tubular re- actors was modeled. Multi-tubular fixed-bed reactor used for ODHP process, employing 10000 of small diame...An industrial scale propylene production via oxidative dehydrogenation of propane （ODHP） in multi-tubular re- actors was modeled. Multi-tubular fixed-bed reactor used for ODHP process, employing 10000 of small diameter tubes immersed in a shell through a proper coolant flows. Herein, a theory-based pseudo-homogeneous model to describe the operation of a fixed bed reactor for the ODHP to correspondence olefln over V2O5/γ-Al203 catalyst was presented. Steady state one dimensional model has been developed to identify the operation parameters and to describe the propane and oxygen conversions, gas process and coolant temperatures, as well as other pa- rameters affecting the reactor performance such as pressure. Furthermore, the applied model showed that a double-bed multitubular reactor with intermediate air injection scheme was superior to a single-bed design due to the increasing of propylene selectivity while operating under lower oxygen partial pressures resulting in propane conversion of about 37.3%. The optimized length of the reactor needed to reach 100% conversion of the oxygen was theoretically determined. For the single-bed reactor the optimized length of 11.96 m including 0.5 m of inert section at the entrance region and for the double-bed reactor design the optimized lengths of 5.72 m for the first and 7.32 m for the second reactor were calculated. Ultimately, the use of a distributed oxygen feed with limited number of injection points indicated a significant improvement on the reactor performance in terms of propane conversion and propylene selectivity. Besides, this concept could overcome the reactor run- away temperature problem and enabled operations at the wider range of conditions to obtain enhanced propyl- ene production in an industrial scale reactor.展开更多
Performance of the oxidative coupling of methane in fluidized-bed reactor was experimentally investigated using Mn-Na2WO4/SiO2,La2O3/CaO and La2O3-SrO/CaO catalysts.These catalysts were found to be stable,especially M...Performance of the oxidative coupling of methane in fluidized-bed reactor was experimentally investigated using Mn-Na2WO4/SiO2,La2O3/CaO and La2O3-SrO/CaO catalysts.These catalysts were found to be stable,especially Mn-Na2WO4/SiO2 catalyst.The effect of sodium content of this catalyst was analyzed and the challenge of catalyst agglomeration was addressed using proper catalyst composition of 2%Mn2.2%Na2WO4/SiO2.For other two catalysts,the effect of Lanthanum-Strontium content was analyzed and 10%La2O 3-20%SrO/CaO catalyst was found to provide higher ethylene yield than La2O3/CaO catalyst.Furthermore,the effect of operating parameters such as temperature and methane to oxygen ratio were also reviewed.The highest ethylene and ethane （C2） yield was achieved with the lowest methane to oxygen ratio around 2.40.5% selectivity to ethylene and ethane and 41% methane conversion were achieved over La2O3-SrO/CaO catalyst while over Mn-Na2WO4 /SiO2 catalyst,40% and 48% were recorded,respectively.Moreover,the consecutive effects of nitrogen dilution,ethylene to ethane production ratio and other performance indicators on the down-stream process units were qualitatively discussed and Mn-Na2WO4/SiO2 catalyst showed a better performance in the reactor and process scale analysis.展开更多
Provskite-type catalysts, Ln0.6 Sr0.4 FexCo1-x O3 (Ln = Nd,Pr, Gd, Sm, La, 0＜x＜1) and Ln0.8Na0.2CoO3(Ln= La,Gd, Sm) were synthesized, their catalytic properties in the oxidative coupling of methane (OCM) were examin...Provskite-type catalysts, Ln0.6 Sr0.4 FexCo1-x O3 (Ln = Nd,Pr, Gd, Sm, La, 0＜x＜1) and Ln0.8Na0.2CoO3(Ln= La,Gd, Sm) were synthesized, their catalytic properties in the oxidative coupling of methane (OCM) were examined in a fixed-bed reactor. The former group presented higher activity in the OCM, but the main product was carbon dioxide. While the later group showed lower activity but much higher selectivity to C2 hydrocarbons compared with the former. Electrochemical measurements were conducted in a solid oxide membrane reactor with La0.8 Na0.2CoO3 as catalyst. The results showed that methane was oxidized to carbon dioxide and ethane by two parallel reactions. Ethane was oxidized to ethene and carbon dioxide. A fraction of ethene was oxidized deeply to carbon dioxide. The total selectivity to C2 hydrocarbons exceeded 70%. Based on the experimental results, a kinetic model was suggested to describe the reaction results.展开更多
The oxidative dehydrogenation of butane to butadiene and butene was studied using a conventional fixed-bed ractor (FBR), inert membrane reactor (IMR) and mixed inert membrane reactor (MIMR). When IMR and MIMR were emp...The oxidative dehydrogenation of butane to butadiene and butene was studied using a conventional fixed-bed ractor (FBR), inert membrane reactor (IMR) and mixed inert membrane reactor (MIMR). When IMR and MIMR were employed, a ceramic membrane modified by partially coating with glaze was used to distribute oxygen to a fixed-bed of 24-V-Mg-O catalyst. The oxygen partial pressure in the catalyst bed could be decreased. The effect of feeding modes and operation conditions were investigated. The selectivity of C4 dehydrogenation products (butene and butadiene) was found to be higher in IMR than in FBR. The feeding mode with 20% of air mixing with butane in MIMR was found to be more efficient than the feeding mode with all air permeating through ceramic membrane. The MIMR gave the most smooth temperature profile along the bed.展开更多
The magnetic perovskite-supported palladium catalysts Pd/Lal_xPbxMnO3 （x = 0.2-0.7） were prepared and used for the oxidative carbonylation of phenol to diphenyl carbonate. The synthesized catalysts were characterize...The magnetic perovskite-supported palladium catalysts Pd/Lal_xPbxMnO3 （x = 0.2-0.7） were prepared and used for the oxidative carbonylation of phenol to diphenyl carbonate. The synthesized catalysts were characterized by the X-ray diffraction （XRD）, surface area measurement BET, vibration sample magnetometer （VSM） and tem- perature-programmed reduction （TPR）. The experimental results demonstrated that the magnetic Pd/La1-xPbxMnO3 （x = 0.4-0.5） obtain relative better catalytic activity. It can be explained by higher concentration of oxygen vacan- cies, larger amount and better mobility of lattice oxygen of their support. Furthermore, these samples possess suffi- cient saturated magnetization. Thus, Pd/La1-xPbxMnO3 （x = 0.4-0.5） may be suitable for operation in the magneti- cally stabilized bed reactor.展开更多
采用自制锰铈氧化物稀土催化剂间歇式反应釜催化湿式氧化(catalytic wet air oxidation,CWAO)处理高质量浓度苯酚废水,研究催化剂粒径、反应温度、系统氧分压、配水苯酚质量浓度、催化剂投加量、配水pH值等参数对湿式氧化处理效果的影响...采用自制锰铈氧化物稀土催化剂间歇式反应釜催化湿式氧化(catalytic wet air oxidation,CWAO)处理高质量浓度苯酚废水,研究催化剂粒径、反应温度、系统氧分压、配水苯酚质量浓度、催化剂投加量、配水pH值等参数对湿式氧化处理效果的影响.研究表明,催化剂粒径>200目时基本消除CWAO反应内扩散传质影响,较低温度下(100℃)CWAO可基本完全氧化处理苯酚废水,氧分压的提高仅加快了CWAO的反应进程,CWAO反应产生抑制与催化剂投加量和配水苯酚质量浓度之比相关,弱酸性条件最适于CWAO反应.催化剂失活的机理在于催化剂表面积碳.展开更多
采用二维拟均相反应器数学模型对国产 YS 型银催化剂的反应性能和反应器运行状况进行了模拟计算和操作分析,并与工业实际数据及相关实验研究结果进行了比较。计算结果和分析表明,相同反应操作条件下,提高乙烯和氧的浓度可加速反应的进行...采用二维拟均相反应器数学模型对国产 YS 型银催化剂的反应性能和反应器运行状况进行了模拟计算和操作分析,并与工业实际数据及相关实验研究结果进行了比较。计算结果和分析表明,相同反应操作条件下,提高乙烯和氧的浓度可加速反应的进行,增加环氧乙烷的产量,其中氧浓度的影响更大,其浓度提高可明显增加 EO 的选择性;二氧化碳对主、副反应均有抑制作用,其浓度提高对生产不利;适当增加抑制剂 EDC 的量有利于提高催化剂的选择性;提高操作空速有利于改善反应状况和提高 EO 产量。分析表明,甲烷致稳较氮气致稳具有明显的优越性,有利于改善催化剂床层的温度分布、提高反应器运行的热稳定性和 EO 生成的选择性。展开更多
基金supported by the National Basic Research Program of China(Project No. 2005CB221405)
文摘A dual-bed reactor was constructed comprising of a 5%Na2WO4-2%Mn/SiO2 particle catalyst and a 4%Ce-5%Na2WO4-2%Mn/SiO2 /cordierite monolithic catalyst.The reaction performance of the oxidative coupling of methane （OCM） over the dual-bed reactor system was evaluated.The effects of the bed height and operation mode,as well as the reaction parameters such as reaction temperature,CH4/O2 ratio and flowrate of feed gas,on the catalytic performance were investigated.The results indicated that the suggested dual-bed reactor exhibited a good performance for the OCM reaction when the feed gases firstly passed through the particle catalyst bed and then to the monolithic catalyst bed.A CH4 conversion of 38.2% and a C2H4 selectivity of 43.3% could be obtained using the dual-bed reactor with a particle catalyst bed height of 10 mm and a monolithic catalyst bed height of 50 mm.Both the CH4 conversion and C2H4 selectivity have increased by 2.5% and 12.8%,respectively,as compared with the 5%Na2WO4-2%Mn/SiO2 particle catalyst in a conventional single-bed reactor and by 12.9% and 23.0%,respectively,as compared with the 4%Ce-5%Na2WO4-2%Mn/SiO2 /cordierite monolithic catalyst in a single-bed reactor.The catalytic performance of the OCM in the dual-bed reactor system has been improved remarkably.
基金Supported by the National Basic Research Program of China(2005CB221405)
文摘A three-dimensional geometric model was set up for the oxidative coupling of methane(OCM) fixed bed reactor loaded with Na_3PO_4-Mn/SiO_2/cordierite monolithic catalyst,and an improved Stansch kinetic model was established to calculate the OCM reactions using the computational fluid dynamics method and Fluent software.The simulation conditions were completely the same with the experimental conditions that the volume velocity of the reactant is 80 ml·min^(-1) under standard state,the CH_4/O_2 ratio is 3 and the temperature and pressure is800 ℃ and 1 atm,respectively.The contour of the characteristic parameters in the catalyst bed was analyzed,such as the species mass fractions,temperature,the heat flux on side wall surface,pressure,fluid density and velocity.The results showed that the calculated values matched well with the experimental values on the conversion of CH4 and the selectivity of products(C_2H_6,C_2H_4,CO,CO_2 and H_2) in the reactor outlet with an error range of±4%.The mass fractions of CH_4 and O_2 decreased from 0.600 and 0.400 at the catalyst bed inlet to 0.445 and0.120 at the outlet,where the mass fractions of C_2H_6,C_2H_4,CO and CO_2 were 0.0245,0.0460,0.0537 and 0.116,respectively.Due to the existence of laminar boundary layer,the mass fraction contours of each species bent upwards in the vicinity of the boundary layer.The volume of OCM reaction was changing with the proceeding of reaction,and the total moles of products were greater than reactants.The flow field in the catalyst bed maintained constant temperature and pressure.The fluid density decreased gradually from 2.28 kg·m^(-3) at the inlet of the catalyst bed to 2.18 kg·m^(-3) at the outlet of the catalyst bed,while the average velocity magnitude increased from 0.108 m·s-1 to 0.120 m·s^(-1).
基金Project(2009T100100602) supported by the Korea Institute of Energy Technology Evaluation and Planning,Korea
文摘A solution of 0.1 mol/L to 1.0 mol/L H2SO4 can dissolve alkali metals and alkaline earth metals which weaken an active site of SCR catalyst. The waste catalyst washed with 0.5 mol/L H2SO4 regained the best catalytic activity. When a concentration of the sulfuric acid is less than 0.5 mol/L, sufficient cleaning effects cannot be obtained. In contrast, when the concentration is greater than 1.0 tool/L, the active components, vanadium and tungsten are undesirably eluted. The total BET surface of the catalyst regenerated by air lift loop reactor showed almost the same as that of fresh catalyst due to the removal of insoluble compounds which may be penetrated into pores of catalyst. The addition of a solution of 0.075 mol/L ammonium vanadate （NHnVO3） and 0.075 mol/L ammonium paratungstate （5（NH4）20· 12WO3-5H20） to 0.1 mol/L H2SO4 significantly increases the activity of the waste catalyst.
文摘An industrial scale propylene production via oxidative dehydrogenation of propane （ODHP） in multi-tubular re- actors was modeled. Multi-tubular fixed-bed reactor used for ODHP process, employing 10000 of small diameter tubes immersed in a shell through a proper coolant flows. Herein, a theory-based pseudo-homogeneous model to describe the operation of a fixed bed reactor for the ODHP to correspondence olefln over V2O5/γ-Al203 catalyst was presented. Steady state one dimensional model has been developed to identify the operation parameters and to describe the propane and oxygen conversions, gas process and coolant temperatures, as well as other pa- rameters affecting the reactor performance such as pressure. Furthermore, the applied model showed that a double-bed multitubular reactor with intermediate air injection scheme was superior to a single-bed design due to the increasing of propylene selectivity while operating under lower oxygen partial pressures resulting in propane conversion of about 37.3%. The optimized length of the reactor needed to reach 100% conversion of the oxygen was theoretically determined. For the single-bed reactor the optimized length of 11.96 m including 0.5 m of inert section at the entrance region and for the double-bed reactor design the optimized lengths of 5.72 m for the first and 7.32 m for the second reactor were calculated. Ultimately, the use of a distributed oxygen feed with limited number of injection points indicated a significant improvement on the reactor performance in terms of propane conversion and propylene selectivity. Besides, this concept could overcome the reactor run- away temperature problem and enabled operations at the wider range of conditions to obtain enhanced propyl- ene production in an industrial scale reactor.
基金supported by the Deutsche Forschungsgemeinschaft (DFG)
文摘Performance of the oxidative coupling of methane in fluidized-bed reactor was experimentally investigated using Mn-Na2WO4/SiO2,La2O3/CaO and La2O3-SrO/CaO catalysts.These catalysts were found to be stable,especially Mn-Na2WO4/SiO2 catalyst.The effect of sodium content of this catalyst was analyzed and the challenge of catalyst agglomeration was addressed using proper catalyst composition of 2%Mn2.2%Na2WO4/SiO2.For other two catalysts,the effect of Lanthanum-Strontium content was analyzed and 10%La2O 3-20%SrO/CaO catalyst was found to provide higher ethylene yield than La2O3/CaO catalyst.Furthermore,the effect of operating parameters such as temperature and methane to oxygen ratio were also reviewed.The highest ethylene and ethane （C2） yield was achieved with the lowest methane to oxygen ratio around 2.40.5% selectivity to ethylene and ethane and 41% methane conversion were achieved over La2O3-SrO/CaO catalyst while over Mn-Na2WO4 /SiO2 catalyst,40% and 48% were recorded,respectively.Moreover,the consecutive effects of nitrogen dilution,ethylene to ethane production ratio and other performance indicators on the down-stream process units were qualitatively discussed and Mn-Na2WO4/SiO2 catalyst showed a better performance in the reactor and process scale analysis.
基金This work was supported supported by the Center Petrochemical Company of China (X599027).
文摘Provskite-type catalysts, Ln0.6 Sr0.4 FexCo1-x O3 (Ln = Nd,Pr, Gd, Sm, La, 0＜x＜1) and Ln0.8Na0.2CoO3(Ln= La,Gd, Sm) were synthesized, their catalytic properties in the oxidative coupling of methane (OCM) were examined in a fixed-bed reactor. The former group presented higher activity in the OCM, but the main product was carbon dioxide. While the later group showed lower activity but much higher selectivity to C2 hydrocarbons compared with the former. Electrochemical measurements were conducted in a solid oxide membrane reactor with La0.8 Na0.2CoO3 as catalyst. The results showed that methane was oxidized to carbon dioxide and ethane by two parallel reactions. Ethane was oxidized to ethene and carbon dioxide. A fraction of ethene was oxidized deeply to carbon dioxide. The total selectivity to C2 hydrocarbons exceeded 70%. Based on the experimental results, a kinetic model was suggested to describe the reaction results.
基金Supported by the National Natural Science Foundation of China(No.29776005).
文摘The oxidative dehydrogenation of butane to butadiene and butene was studied using a conventional fixed-bed ractor (FBR), inert membrane reactor (IMR) and mixed inert membrane reactor (MIMR). When IMR and MIMR were employed, a ceramic membrane modified by partially coating with glaze was used to distribute oxygen to a fixed-bed of 24-V-Mg-O catalyst. The oxygen partial pressure in the catalyst bed could be decreased. The effect of feeding modes and operation conditions were investigated. The selectivity of C4 dehydrogenation products (butene and butadiene) was found to be higher in IMR than in FBR. The feeding mode with 20% of air mixing with butane in MIMR was found to be more efficient than the feeding mode with all air permeating through ceramic membrane. The MIMR gave the most smooth temperature profile along the bed.
基金Supported by the Key Program of National Natural Science Foundation of China(20936003)the Foundation for Innovation Research Groups of the Natural Science Foundation of Hubei Province(2008CDA009)
文摘The magnetic perovskite-supported palladium catalysts Pd/Lal_xPbxMnO3 （x = 0.2-0.7） were prepared and used for the oxidative carbonylation of phenol to diphenyl carbonate. The synthesized catalysts were characterized by the X-ray diffraction （XRD）, surface area measurement BET, vibration sample magnetometer （VSM） and tem- perature-programmed reduction （TPR）. The experimental results demonstrated that the magnetic Pd/La1-xPbxMnO3 （x = 0.4-0.5） obtain relative better catalytic activity. It can be explained by higher concentration of oxygen vacan- cies, larger amount and better mobility of lattice oxygen of their support. Furthermore, these samples possess suffi- cient saturated magnetization. Thus, Pd/La1-xPbxMnO3 （x = 0.4-0.5） may be suitable for operation in the magneti- cally stabilized bed reactor.
文摘采用自制锰铈氧化物稀土催化剂间歇式反应釜催化湿式氧化(catalytic wet air oxidation,CWAO)处理高质量浓度苯酚废水,研究催化剂粒径、反应温度、系统氧分压、配水苯酚质量浓度、催化剂投加量、配水pH值等参数对湿式氧化处理效果的影响.研究表明,催化剂粒径>200目时基本消除CWAO反应内扩散传质影响,较低温度下(100℃)CWAO可基本完全氧化处理苯酚废水,氧分压的提高仅加快了CWAO的反应进程,CWAO反应产生抑制与催化剂投加量和配水苯酚质量浓度之比相关,弱酸性条件最适于CWAO反应.催化剂失活的机理在于催化剂表面积碳.
文摘采用二维拟均相反应器数学模型对国产 YS 型银催化剂的反应性能和反应器运行状况进行了模拟计算和操作分析,并与工业实际数据及相关实验研究结果进行了比较。计算结果和分析表明,相同反应操作条件下,提高乙烯和氧的浓度可加速反应的进行,增加环氧乙烷的产量,其中氧浓度的影响更大,其浓度提高可明显增加 EO 的选择性;二氧化碳对主、副反应均有抑制作用,其浓度提高对生产不利;适当增加抑制剂 EDC 的量有利于提高催化剂的选择性;提高操作空速有利于改善反应状况和提高 EO 产量。分析表明,甲烷致稳较氮气致稳具有明显的优越性,有利于改善催化剂床层的温度分布、提高反应器运行的热稳定性和 EO 生成的选择性。
