In a probe and drogue aerial refueling system, the bow wave of the receiver aircraft will produce a strong aerodynamic effect on the drogue once the receiver follows the drogue at a close distance. It is a major diffi...In a probe and drogue aerial refueling system, the bow wave of the receiver aircraft will produce a strong aerodynamic effect on the drogue once the receiver follows the drogue at a close distance. It is a major difficulty of docking control in the probe and drogue refueling. This paper analyses the bow wave effect and presents a simple method to model it. Firstly, the inviscid flow around the receiver is modeled based on the stream function defined by basic stream singularities. Secondly, a correction function is developed to eliminate the error caused by the absence of air vis- cosity. Then, the aerodynamic coefficients are used to calculate the induced aerodynamic force on the drogue. The obtained model is in an analytical form that can be easily applied to the controller design and the real-time simulations. In the verification part, computational fluid dynamics （CFD） simulation tests are conducted to validate the obtained flow fields and aerodynamic forces. Finally, the modeling method is applied to an F-16 receiver aircraft in a previously developed autonomous aerial refueling simulation system. The simulations results are analyzed and compared with the NASA flight-test data, which demonstrates the effectiveness of the proposed method.展开更多
Background: The hepatic hemodynamics is an essential parameter in surgical planning as well as in various disease processes. The transit time ultrasound(TTUS) perivascular flow probe technology is widely used in clini...Background: The hepatic hemodynamics is an essential parameter in surgical planning as well as in various disease processes. The transit time ultrasound(TTUS) perivascular flow probe technology is widely used in clinical practice to evaluate the hepatic inflow, yet invasive. The phase-contrast-MRI(PC-MRI) is not invasive and potentially applicable in assessing the hepatic blood flow. In the present study, we compared the hepatic inflow rates using the PC-MRI and the TTUS probe, and evaluated their predictive value of post-hepatectomy adverse events. Methods: Eighteen large white pigs were anaesthetized for PC-MRI and approximately 75% hepatic resection was performed under a unified protocol. The blood flow was measured in the hepatic artery(Qha), the portal vein(Qpv), and the aorta above the celiac trunk(Qca) using PC-MRI, and was compared to the TTUS probe. The Bland-Altman method was conducted and a partial least squares regression(PLS) model was implemented. Results: The mean Qpv measured in PC-MRI was 0.55 ± 0.12 L/min, and in the TTUS probe was 0.74 ± 0.17 L/min. Qca was 1.40 ± 0.47 L/min in the PC-MRI and 2.00 ± 0.60 L/min in the TTUS probe. Qha was 0.17 ± 0.10 L/min in the PC-MRI, and 0.13 ± 0.06 L/min in the TTUS probe. The Bland-Altman method revealed that the estimated bias of Qca in the PC-MRI was 32%(95% CI:-49% to 15%); Qha 17%(95% CI:-15% to 51%); and Qpv 40%(95% CI:-62% to 18%). The TTUS probe had a higher weight in predicting adverse outcomes after 75% resection compared to the PC-MRI( β= 0.35 and 0.43 vs β = 0.22 and 0.07, for tissue changes and premature death, respectively). Conclusions: There is a tendency of the PC-MRI to underestimate the flow measured by the TTUS probes. The TTUS probe measures are more predictive of relevant post-hepatectomy outcomes.展开更多
The concept of′Probe detector′is introduced in this paper with its application in geometricmodeling and graphics.In terms of the concept,the authors derive edge data from the CSG datarepresentation and establish a w...The concept of′Probe detector′is introduced in this paper with its application in geometricmodeling and graphics.In terms of the concept,the authors derive edge data from the CSG datarepresentation and establish a wireframe model.展开更多
Recent developments in micro- and nano-satellites have attracted the interest of the research community worldwide. Many colleges and corporations have launched their satellites in space. Meanwhile, the space flexible ...Recent developments in micro- and nano-satellites have attracted the interest of the research community worldwide. Many colleges and corporations have launched their satellites in space. Meanwhile, the space flexible probe-cone docking system for micro- and nano-satellites has become an attractive topic. In this paper, a dynamic model of a space flexible probe-cone dock- ing system, in which the flexible beam technology is applied, is built based on the Kane method. The curves of impact force versus time are obtained by the Lagrange model, the Kane model, and the experimental method. The Lagrange model was presented in the reference and verified by both finite element simulation and experiment. The results of the three methods show good agreements on the condition that the beam flexibility and the initial relative velocity change. It is worth mentioning that the introduction of vectorial mechanics and analytical mechanics in the Kane method leads to a large reduction of differential operations and makes the modeling process much easier than that of the Lagrange method. Moreover, the influences of the beam flexibility and the initial relative velocity are discussed. It is concluded that the initial relative velocity of space docking operation should be controlled to a certain value in order to protect the docking system.展开更多
Three-dimensional atom probe （3DAP） technique has been used to study the nucleation and growth of M23C6 carbide in a supersaturated multi-component Fe-based alloy aged at 800℃. 3D images indicate that the radius of...Three-dimensional atom probe （3DAP） technique has been used to study the nucleation and growth of M23C6 carbide in a supersaturated multi-component Fe-based alloy aged at 800℃. 3D images indicate that the radius of M23C6 carbide after ageing for 10 min is about 9 nm. Concentration profiles of alloy elements in the carbide are also obtained. Combined with PANDAT and Thermo-Calc software, attempts to model the early stages of precipitation are present. The calculated particle size and composition of M23C6 carbide is in good agreement with 3DAP data.展开更多
The present paper covers the response dynamics of a gas-sensing membrane probe, which is described by the dynamic differential equation based upon a steady-state diffusion process. The theoretical results indicate tha...The present paper covers the response dynamics of a gas-sensing membrane probe, which is described by the dynamic differential equation based upon a steady-state diffusion process. The theoretical results indicate that the response time is dependent upon membrane properties, membrane geometry, internal electrolyte composition, the dissociation constant of the conjugate reaction, the initial gas concentration in the internal electrolyte, and the gas concentration in the evaluation sample. The theoretical prediction is in good agreement with the experimental result. A method for determining a gas-sensing probe' s dynamic parameter is proposed in this paper also.展开更多
Packet-pair sampling, also called probe gap model (PGM) is proposed as a lightweight and fast available bandwidth measurement method. But measurement tools based on PGM gives results with great uncertainty in some cas...Packet-pair sampling, also called probe gap model (PGM) is proposed as a lightweight and fast available bandwidth measurement method. But measurement tools based on PGM gives results with great uncertainty in some cases. PGM’s statistical robustness has not been proved. In this paper we propose a more precise statistical model based on PGM. We present the new approach by using probability distribution and statistical parameters. We also investigate the use of a PGM bandwidth evaluation method considering a non-fluid cross traffic and present the alternative approach where the bursty nature of the probed traffic could be taken into account. Based on the model, measurement variance and sample size can be calculated to improve the measurement accuracy. We evaluated the model in a controlled and reproducible environment using NS simulations.展开更多
The hairpin probe using microwave resonance in plasma is applicable to high pressure 1.33 ×10^3-1.01×10^5 Pa）） as developed recently. In this work, an analytic model of the hairpin resonator probe surround...The hairpin probe using microwave resonance in plasma is applicable to high pressure 1.33 ×10^3-1.01×10^5 Pa）） as developed recently. In this work, an analytic model of the hairpin resonator probe surrounded by a thin dielectric layer and a sheath layer is proposed. The correction factor due to these surroundings is analytically found and confirmed by electromagnetic field finite difference time domain simulation, thus enabling the accurate measurement of electron density in a high-pressure non-equilibrium uniform discharge.展开更多
This paper proposes a simple collisional-radiative model to characterise capacitively coupled argon plasmas driven by conventional radio frequency in combination with optical emission spectroscopy and Langmuir probe m...This paper proposes a simple collisional-radiative model to characterise capacitively coupled argon plasmas driven by conventional radio frequency in combination with optical emission spectroscopy and Langmuir probe measurements. Two major processes are considered in this model, electron-impact excitation and the spontaneous radiative decay. The diffusion loss term, which is found to be important for the two metastable states （4s[3/2]2, 4s＇[1/2]0）, is also taken into account. Behaviours of representative metastable and radiative states are discussed. Two emission lines （located at 696.5 nm and 750.4 nm） are selected and intensities are measured to obtain populated densities of the corresponding radiative states in the argon plasma. The calculated results agree well with that measured by Langmuir probe, indicating that the current model combined with optical emission spectroscopy is a candidate tool for electron density and temperature measurement in radio frequency capacitively coupled discharges.展开更多
This paper describes experimental investigations of flow structures and related transport processes in the continuous casting mould under the influence of an external DC magnetic field at laboratory scale.Experimental...This paper describes experimental investigations of flow structures and related transport processes in the continuous casting mould under the influence of an external DC magnetic field at laboratory scale.Experimental results will be presented here which have been obtained using a physical model(mini-LIMMCAST)operating with the low melting point alloy GaInSn.According to the concept of the electromagnetic brake the impact of a DC magnetic field on the outlet flow from the Submerged Entry Nozzle(SEN)has been studied up to Hartmann numbers of about 400.The Ultrasound-Doppler-Velocimetry(UDV)was applied for measurements of the flow pattern in the mould.Local conductivity anemometers were used to measure the turbulent quantities of the flow.The effect of the magnetic field on the flow structure turned out to be manifold and rather complex.The magnetic field causes a deflection of the jet,at which the respective exit angle from the nozzle ports becomes more flat.Thus,both the penetration depth of the discharging flow into the lower part of the mould and the impinging velocity of the jet onto the side wall are reduced.A significant return flow occurs in the adjacent regions of the jet.Specific vortices are formed with axes being aligned with the magnetic field direction.Such vortical structures are typical for quasi-two-dimensional magneto-hydrodynamic(MHD)flows.The flow measurements do not manifest a general braking effect which would be expected as an overall damping of the flow velocity and the related fluctuations all-over the mould volume.Variations of the wall conductivity showed a striking impact on the resulting flow structures.展开更多
基金supported by the National Natural Science Foundation of China(Nos.61473012 and 51375462)
文摘In a probe and drogue aerial refueling system, the bow wave of the receiver aircraft will produce a strong aerodynamic effect on the drogue once the receiver follows the drogue at a close distance. It is a major difficulty of docking control in the probe and drogue refueling. This paper analyses the bow wave effect and presents a simple method to model it. Firstly, the inviscid flow around the receiver is modeled based on the stream function defined by basic stream singularities. Secondly, a correction function is developed to eliminate the error caused by the absence of air vis- cosity. Then, the aerodynamic coefficients are used to calculate the induced aerodynamic force on the drogue. The obtained model is in an analytical form that can be easily applied to the controller design and the real-time simulations. In the verification part, computational fluid dynamics （CFD） simulation tests are conducted to validate the obtained flow fields and aerodynamic forces. Finally, the modeling method is applied to an F-16 receiver aircraft in a previously developed autonomous aerial refueling simulation system. The simulations results are analyzed and compared with the NASA flight-test data, which demonstrates the effectiveness of the proposed method.
基金supported mainly by the “Agence de la Biomedecine” through its program of Research(AOR 2009)BM,AC,BP,WM,VCI and VE acknowledged funding of project ANR-13-TECS-0006 by the Agence Nationale de la Recherche
文摘Background: The hepatic hemodynamics is an essential parameter in surgical planning as well as in various disease processes. The transit time ultrasound(TTUS) perivascular flow probe technology is widely used in clinical practice to evaluate the hepatic inflow, yet invasive. The phase-contrast-MRI(PC-MRI) is not invasive and potentially applicable in assessing the hepatic blood flow. In the present study, we compared the hepatic inflow rates using the PC-MRI and the TTUS probe, and evaluated their predictive value of post-hepatectomy adverse events. Methods: Eighteen large white pigs were anaesthetized for PC-MRI and approximately 75% hepatic resection was performed under a unified protocol. The blood flow was measured in the hepatic artery(Qha), the portal vein(Qpv), and the aorta above the celiac trunk(Qca) using PC-MRI, and was compared to the TTUS probe. The Bland-Altman method was conducted and a partial least squares regression(PLS) model was implemented. Results: The mean Qpv measured in PC-MRI was 0.55 ± 0.12 L/min, and in the TTUS probe was 0.74 ± 0.17 L/min. Qca was 1.40 ± 0.47 L/min in the PC-MRI and 2.00 ± 0.60 L/min in the TTUS probe. Qha was 0.17 ± 0.10 L/min in the PC-MRI, and 0.13 ± 0.06 L/min in the TTUS probe. The Bland-Altman method revealed that the estimated bias of Qca in the PC-MRI was 32%(95% CI:-49% to 15%); Qha 17%(95% CI:-15% to 51%); and Qpv 40%(95% CI:-62% to 18%). The TTUS probe had a higher weight in predicting adverse outcomes after 75% resection compared to the PC-MRI( β= 0.35 and 0.43 vs β = 0.22 and 0.07, for tissue changes and premature death, respectively). Conclusions: There is a tendency of the PC-MRI to underestimate the flow measured by the TTUS probes. The TTUS probe measures are more predictive of relevant post-hepatectomy outcomes.
文摘The concept of′Probe detector′is introduced in this paper with its application in geometricmodeling and graphics.In terms of the concept,the authors derive edge data from the CSG datarepresentation and establish a wireframe model.
基金supported in part by the National Natural Science Foundation of China (Nos. 91216201, 51205403)
文摘Recent developments in micro- and nano-satellites have attracted the interest of the research community worldwide. Many colleges and corporations have launched their satellites in space. Meanwhile, the space flexible probe-cone docking system for micro- and nano-satellites has become an attractive topic. In this paper, a dynamic model of a space flexible probe-cone dock- ing system, in which the flexible beam technology is applied, is built based on the Kane method. The curves of impact force versus time are obtained by the Lagrange model, the Kane model, and the experimental method. The Lagrange model was presented in the reference and verified by both finite element simulation and experiment. The results of the three methods show good agreements on the condition that the beam flexibility and the initial relative velocity change. It is worth mentioning that the introduction of vectorial mechanics and analytical mechanics in the Kane method leads to a large reduction of differential operations and makes the modeling process much easier than that of the Lagrange method. Moreover, the influences of the beam flexibility and the initial relative velocity are discussed. It is concluded that the initial relative velocity of space docking operation should be controlled to a certain value in order to protect the docking system.
基金supported by the National Natural Science Foundation of China (Nos. 50971137 and 50934011)
文摘Three-dimensional atom probe （3DAP） technique has been used to study the nucleation and growth of M23C6 carbide in a supersaturated multi-component Fe-based alloy aged at 800℃. 3D images indicate that the radius of M23C6 carbide after ageing for 10 min is about 9 nm. Concentration profiles of alloy elements in the carbide are also obtained. Combined with PANDAT and Thermo-Calc software, attempts to model the early stages of precipitation are present. The calculated particle size and composition of M23C6 carbide is in good agreement with 3DAP data.
文摘The present paper covers the response dynamics of a gas-sensing membrane probe, which is described by the dynamic differential equation based upon a steady-state diffusion process. The theoretical results indicate that the response time is dependent upon membrane properties, membrane geometry, internal electrolyte composition, the dissociation constant of the conjugate reaction, the initial gas concentration in the internal electrolyte, and the gas concentration in the evaluation sample. The theoretical prediction is in good agreement with the experimental result. A method for determining a gas-sensing probe' s dynamic parameter is proposed in this paper also.
文摘Packet-pair sampling, also called probe gap model (PGM) is proposed as a lightweight and fast available bandwidth measurement method. But measurement tools based on PGM gives results with great uncertainty in some cases. PGM’s statistical robustness has not been proved. In this paper we propose a more precise statistical model based on PGM. We present the new approach by using probability distribution and statistical parameters. We also investigate the use of a PGM bandwidth evaluation method considering a non-fluid cross traffic and present the alternative approach where the bursty nature of the probed traffic could be taken into account. Based on the model, measurement variance and sample size can be calculated to improve the measurement accuracy. We evaluated the model in a controlled and reproducible environment using NS simulations.
基金supported by the National Natural Science Foundation of China (Grant No. 10835004 )the 2nd Knowledge Cluster Research Project of Japan:Tokai Region Nanotechnology Manufacturing Cluster (Innovation of Environment Friendly Highly Functional Materials and Devices)
文摘The hairpin probe using microwave resonance in plasma is applicable to high pressure 1.33 ×10^3-1.01×10^5 Pa）） as developed recently. In this work, an analytic model of the hairpin resonator probe surrounded by a thin dielectric layer and a sheath layer is proposed. The correction factor due to these surroundings is analytically found and confirmed by electromagnetic field finite difference time domain simulation, thus enabling the accurate measurement of electron density in a high-pressure non-equilibrium uniform discharge.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.10635010 and 10775103)
文摘This paper proposes a simple collisional-radiative model to characterise capacitively coupled argon plasmas driven by conventional radio frequency in combination with optical emission spectroscopy and Langmuir probe measurements. Two major processes are considered in this model, electron-impact excitation and the spontaneous radiative decay. The diffusion loss term, which is found to be important for the two metastable states （4s[3/2]2, 4s＇[1/2]0）, is also taken into account. Behaviours of representative metastable and radiative states are discussed. Two emission lines （located at 696.5 nm and 750.4 nm） are selected and intensities are measured to obtain populated densities of the corresponding radiative states in the argon plasma. The calculated results agree well with that measured by Langmuir probe, indicating that the current model combined with optical emission spectroscopy is a candidate tool for electron density and temperature measurement in radio frequency capacitively coupled discharges.
基金Item Sponsored by Deutsche Forschungsgemeinschaft (DFG) as Part of the Collaborative Research Centre SFB609 "Electromagnetic Flow Control in Metallurgy,Crystal Growth and Electrochemistry"
文摘This paper describes experimental investigations of flow structures and related transport processes in the continuous casting mould under the influence of an external DC magnetic field at laboratory scale.Experimental results will be presented here which have been obtained using a physical model(mini-LIMMCAST)operating with the low melting point alloy GaInSn.According to the concept of the electromagnetic brake the impact of a DC magnetic field on the outlet flow from the Submerged Entry Nozzle(SEN)has been studied up to Hartmann numbers of about 400.The Ultrasound-Doppler-Velocimetry(UDV)was applied for measurements of the flow pattern in the mould.Local conductivity anemometers were used to measure the turbulent quantities of the flow.The effect of the magnetic field on the flow structure turned out to be manifold and rather complex.The magnetic field causes a deflection of the jet,at which the respective exit angle from the nozzle ports becomes more flat.Thus,both the penetration depth of the discharging flow into the lower part of the mould and the impinging velocity of the jet onto the side wall are reduced.A significant return flow occurs in the adjacent regions of the jet.Specific vortices are formed with axes being aligned with the magnetic field direction.Such vortical structures are typical for quasi-two-dimensional magneto-hydrodynamic(MHD)flows.The flow measurements do not manifest a general braking effect which would be expected as an overall damping of the flow velocity and the related fluctuations all-over the mould volume.Variations of the wall conductivity showed a striking impact on the resulting flow structures.
