The Makran accretionary wedge has the smallest subduction angle among any accretionary prism in the world. The factors controlling the spacing and morphological development of its deep thrust faults, as well as the fo...The Makran accretionary wedge has the smallest subduction angle among any accretionary prism in the world. The factors controlling the spacing and morphological development of its deep thrust faults, as well as the formation mechanism of shallow normal faults, remain unclear. Meanwhile, the factors affecting the continuity of plane faults must be comprehensively discussed. Clarifying the development characteristics and deformation mechanisms of the Makran accretionary wedge is crucial to effectively guide the exploration of gas hydrate deposits in the area. This study aims to interpret seismic data to identify typical structures in the Makran accretionary wedge, including deep imbricate thrust faults, shallow and small normal faults, wedge-shaped piggyback basins, mud diapirs with fuzzy and disorderly characteristics of reflection, décollements with a northward tilt of 1° – 2°, and large seamounts. Physical simulation-based experiments are performed to comprehensively analyze the results of the plane, section, and slices of the wedge. Results reveal that the distances between and shapes of thrust faults in the deep parts of the Makran accretionary wedge are controlled by the bottom décollement. The uplift of the thrust fault-related folds and the upwelling of the mud diapirs primarily contribute to the formation of small normal faults in the shallow part of the area. The mud diapirs originate from plastic material at the bottom, while those that have developed in the area near the trench are larger. Seamounts and mud diapirs break the continuity of fault plane distribution.展开更多
The contrast experiment of different stirring modes,which includes a new type of stirring-injection with the method of pulse and rotation,and the initial one-way stirring method,is done through physical simulation in ...The contrast experiment of different stirring modes,which includes a new type of stirring-injection with the method of pulse and rotation,and the initial one-way stirring method,is done through physical simulation in the laboratory.The stirring methods of pulse and rotation are of two kinds.One is pulsed and rotary stirrer with positive and opposite directions.The other is pulsed and rotary stirrer with rotation-stop-rotation.The results show that the stirring mode of pulse and rotation has better effects than the one-way stirring method.The specific effects are that the mixing time of the melting bath is apparently shortened,the number of grains involved in the liquid surface is increased,and the residence time of air bubble in water is doubled.展开更多
Coal and gas outburst is one of the main gas hazards in coal mines. However, due to the risks of the coal and gas outburst, the field test is difficult to complete. Therefore, an effective approach to studying the mec...Coal and gas outburst is one of the main gas hazards in coal mines. However, due to the risks of the coal and gas outburst, the field test is difficult to complete. Therefore, an effective approach to studying the mechanism and development of outburst is to conduct the similar physical simulation. However, the similarity criteria and similar materials in outburst are the key factors which restrict the development of physical simulation. To solve those problems, this paper has established similarity criteria base on mechanics model, solid-fluid coupling model and energy model, and presented high similar materials. Combining with three groups of similar number, and considering similar mechanical parameters and deformation and failure regularity, the similarity criteria of outburst is determined on the basis of the energy model. According to those criteria, we put forward a similar material consists of pulverized coal, cement, sand, activated carbon, and water. The similar material has high compressive strength and the accordant characteristics with the raw coal, include density, porosity, adsorption, desorption. The new research is promising for preventing and controlling gas hazards in the future.展开更多
The kinetics of ε-Cu particles dissolution in the matrix during welding of a copper-precipitation strengthening steel was determined by a combination of GleebleTM physical simulation, TEM examination and hardness mea...The kinetics of ε-Cu particles dissolution in the matrix during welding of a copper-precipitation strengthening steel was determined by a combination of GleebleTM physical simulation, TEM examination and hardness meas urement. The ε-Cu particles underwent a coarsening and part dissolution and then complete dissolution reaction as the peak temperature increased from 750 to 1 000℃, which resulted in the decrease in the number density of ε-Cu particles and hardness in the heat affected zone （HAZ）. The results can be used to understand the evolution of this transformation and a softening behavior of the HAZ during welding of this type of steel.展开更多
To establish the relationship among reservoir characteristics and rock physical parameters,we construct the well-bore rock physical models firstly,considering the influence factors,such as mineral composition,shale co...To establish the relationship among reservoir characteristics and rock physical parameters,we construct the well-bore rock physical models firstly,considering the influence factors,such as mineral composition,shale content,porosity,fluid type and saturation.Then with analyzing the change rules of elastic parameters along with the above influence factors and the cross-plots among elastic parameters,the sensitive elastic parameters of tight sandstone reservoir are determined,and the rock physics template of sweet spot is constructed to guide pre-stack seismic inversion.The results show that velocity ratio and Poisson impedance are the most sensitive elastic parameters to indicate the lithologic and gas-bearing properties of sweet spot in tight sandstone reservoir.The high-quality sweet spot is characterized by the lower velocity ratio and Poisson impedance.Finally,the actual seismic data are selected to predict the sweet spots in tight sandstone gas reservoirs,so as to verify the validity of the rock physical simulation results.The significant consistency between the relative logging curves and inversion results in different wells implies that the utilization of well-bore rock physical simulation can guide the prediction of sweet spot in tight sandstone gas reservoirs.展开更多
Mold-filling process of thin-walled castings under the condition of traveling magnetic field has been studied by physical simulation method using gallium melt and fast speed photography. Flow morphology and its format...Mold-filling process of thin-walled castings under the condition of traveling magnetic field has been studied by physical simulation method using gallium melt and fast speed photography. Flow morphology and its formation mechanism were obtained and discussed for thin-walled casting. The influences of magnetic field density on the filling ability, filling velocity and mold filling time have been studied. The differences in filling capability between gravity casting and casting under the traveling magnetic field have been compared. The results indicate that the mold filling ability of the gallium melt increases greatly under the condition of traveling magnetic field; the filling time is shortened from 18 s under gravity field to 3 s under the traveling magnetic field and average flow rate of the melt increases from 1.6 to 8.68 cm3/s; the change law of the cross-section morphology of the gallium melt during the mold filling is that at first, the cross-section area does not change, then it decreases gradually. When the front of the melt reaches the end of the mold cavity, the front melt will backfill the mold; the wider the width of mold cavity, the better the mold filling ability. The mold filling ability of gallium melt in mold with upper magnetic conductor is better than that without upper magnetic conductor.展开更多
The behavior of stress wave propagation in rock walls and the process of rock bursts were simulated by application tests of material similar to rock. Results show that 1) the attenuation characteristics of stress wave...The behavior of stress wave propagation in rock walls and the process of rock bursts were simulated by application tests of material similar to rock. Results show that 1) the attenuation characteristics of stress waves were related to the material proper-ties, stress waves attenuate more quickly in soft material and 2) when the explosion load was applied at the top of the roadway, the number and the length of the cracks increased with a decrease in the distance between the explosive point and roof of the roadway. When the distance was 280 mm, only some chips appeared near the source, when the distance was 210 mm, some small cracks started to appear near the road-rib and when the distance was reduced to 140 mm, larger cracks appeared at the road-rib. It can be concluded that, under a given stress the number of cracks is closely related to the intensity of stress waves. The cracks in the sur-rounding rock can be reduced by controlling the intensity of the stress waves and rock bursts can be avoided to some extent by pre-venting the formation of layered crack structures. A new experimental approach has been provided for studying rock bursts by using physical simulation.展开更多
Direct quenching and tempering （DQ-T） of hot rolled steel section has been widely used in steel mill for the sake of improvement of mechanical properties and energy saving. Temperature history and microstructural ev...Direct quenching and tempering （DQ-T） of hot rolled steel section has been widely used in steel mill for the sake of improvement of mechanical properties and energy saving. Temperature history and microstructural evolution during hot rolling plays a major role in the properties of direct quenched and tempered products. The mathematical and physical modeling of hot forming processes is becoming a very important tool for design and development of required products as well as predicting the microstructure and the properties of the components. These models were mostly used to predict austenite grain size （AGS）, dynamic, recta-dynamic and static recrystallization in the rods immediately after hot rolling and prior to DQ process. The hot compression tests were carried out on 42CrMo4 steel in the temperature range of 900-1 100 ℃ and the strain rate range of 0. 05-1 s^-1 in order to study the high tempera- ture softening behavior of the steel. For the exact prediction of flow stress, the effective stress-effective strain curves were obtained from experiments under various conditions. On the basis of experimental results, the dynamic recrystallization fraction （DRX）, AGS, hot deformation and activation energy behavior were investigated. It was found that the calculated results were in good agreement with the experimental flow stress and microstructure of the steel for different conditions of hot deformation.展开更多
According to the test results of the physical and mechanical properties of similar materials in various quality mixture, a type of material with obvious tendency of rockburst was selected to produce a large-size model...According to the test results of the physical and mechanical properties of similar materials in various quality mixture, a type of material with obvious tendency of rockburst was selected to produce a large-size model to simulate rockburst phenomena in tunnels. The prototype model comes from a typical section of diversion tunnels in Jinping Hydropower Station in China. The simulation of excavating tunnels is carried out by opening a hole in the model after loading. The modeling results indicated that under the condition of normal stresses in the model boundaries the arch top, spandrel and side walls of the tunnel produced an obvious jump reaction of stress and strain and the acoustic emission counts of the surrounding rock also increased rapidly in a different time period after the "tunnel" excavation, showing the clear features of rockburst. The spalling, buckling and breaking occurred in the surrounding rock of model in conditions of over loading. It is concluded that the modeling tunnel segment in Jinping Hydropower Station is expected to form the tensile rockburst with the pattern of spalling, buckling and breaking.展开更多
In order to increase the contact area and promote the mass transfer process of gas and liquid,the process of the bubble refine-ment in a metallurgical reactor with mechanical agitation was studied by physical simulati...In order to increase the contact area and promote the mass transfer process of gas and liquid,the process of the bubble refine-ment in a metallurgical reactor with mechanical agitation was studied by physical simulation.Based on the capillary number,a prediction equation for the bubble refinement was established.The effects of the gas flow rate,the stirring speed and thestirring depth on the bubble refinement in the reactor were discussed in detail.The distribution of the bubble diameter in thereactor was obtained under different conditions.The results show that when the stirring speed reaches 300 r/min,the bubblediamcter mainly distributes in the range of 1-2 mm.A higher gas flow rate may increase the number of bubbles in the meltand promote the bubble refinement process.The mechanism of bubble refinement under mechanical agitation was analyzed.and the results indicated that the stirring speed.,the blade area and the blade inclination are the main influencing factors.展开更多
In order to select highly productive and enriched areas of high rank coalbed methane reservoirs, based on hydrologic geology as one of the main factors controlling coalbed methane （CBM） reservoir formations, the eff...In order to select highly productive and enriched areas of high rank coalbed methane reservoirs, based on hydrologic geology as one of the main factors controlling coalbed methane （CBM） reservoir formations, the effect of hydrodynamic forces controlling CBM reservoir formations was studied by a physical simulation experiment in which we used CBM reservoir simulation facilities. The hydrodynamic conditions of high coal rank reservoirs in the Qinshui basin were analyzed. Our experiment shows the following results： under strong hydrodynamic alternating action, 6C~ of coalbed methane reservoir changed from the start at -2.95% ~ -3.66%, and the lightening process occurred in phases; the CI-I4 volume reduced from 96.35% to 12.42%; the CO2 vo- lume decreased from 0.75% in sample 1 to 0.68% in sample 2, then rose to 1.13% in sample 3; the N2 volume changed from 2.9% in sample 1 to 86.45% in sample 3. On one hand, these changes show the complexity of CBM reservoir formation; on the other hand, they indicate that strong hydrodynamic actions have an unfavorable impact on CBM reservoir formation. It was found that the gas volume and hydrodynamic intensity were negatively correlated and low hydrodynamic flow conditions might result in highly productive and enriched areas of high rank CBM.展开更多
Real waves are multidirectional waves. In the present study, the calculation method for the wave maker driving signals for generating multidirectional wave groups in physical wave basin is proposed. Its validity is fi...Real waves are multidirectional waves. In the present study, the calculation method for the wave maker driving signals for generating multidirectional wave groups in physical wave basin is proposed. Its validity is first confirmed by a numerical model for which the incident boundary condition is determined by use of the proposed method. Then, the physical simulation of multidirectional wave groups is performed in laboratory wave basin. The experimental results show that multidirectional waves with expected wave groupiness, which includes not only its group height but also its group length, can be satisfactorily zenerated at the soecified oosition in the tphvsical wave basin.展开更多
Most existing force feedback methods are still difficult to meet the requirements of real-time force calculation in virtual assembly and operation with complex objects. In addition, there is often an assumption that t...Most existing force feedback methods are still difficult to meet the requirements of real-time force calculation in virtual assembly and operation with complex objects. In addition, there is often an assumption that the controlled objects are completely flee and the target object is only completely fixed or flee, thus, the dynamics of the kinematic chain where the controlled objects are located are neglected during the physical simulation of the product manipulation with force feedback interaction. This paper proposes a physical simulation method of product assembly and operation manipulation based on statistically learned contact force prediction model and the coupling of force feedback and dynamics. In the proposed method, based on hidden Markov model （HMM） and local weighting learning （LWL）, contact force prediction model is constructed, which can estimate the contact force in real time during interaction. Based on computational load balance model, the computing resources are dynamically assigned and the dynamics integral step is optimized. In addition, smoothing process is performed to the force feedback on the synchronization points. Consequently, we can solve the coupling and synchronization problems of high-frequency feedback force servo. low-frequency dynamics solver servo and scene rendering servo, and realize highly stable and accurate force feedback in the physical simulation of product assembly and operation manipulation. This research proposes a physical simulation method of product assembly and operation manipulation.展开更多
For extra-low permeability reservoirs, with a permeability of about 0.3×10?3 μm2, fluid flow and production performance in cores were studied. A long core holder with a multi-location piezometric measurement was...For extra-low permeability reservoirs, with a permeability of about 0.3×10?3 μm2, fluid flow and production performance in cores were studied. A long core holder with a multi-location piezometric measurement was specially designed. An artificial long core, about 700 mm long and with a cross section of 45mm×45mm, was used. In the experiment, pressure distribution along the core can be measured in real time. Single phase flow in the core was investigated. Different modes of production in long cores were also simulated including natural depletion, water flooding, and advanced water flooding. Through physical simulation, flow parameters were collected and production characteristics in extra-low permeability cores were studied. From experimental results, it can be seen that fluid flow in extra-low permeability cores is different from that in high permeability cores. Transmission of pressure in extra-low permeability cores is very slow, and it needs a long time for the pressure to become stable. The distribution curve of pressure along the core is nonlinear and the production rate in extra-low permeability reservoirs decreases sharply. The development effects of different production modes in extra-low permeability cores were compared with one another. Among the production modes, advanced water flooding has much potential for effective development of extra-low permeability reservoirs. Natural depletion and conventional water flooding can also be used in early production periods. In addition, the countermeasures and some ideas especially for the potential development of extra-low permeability reservoirs are suggested.展开更多
The method of manufacturing the composite wire by extruding lead to coated glass fiber is described. The different composite wire that diameter is from 0.5 to 1.0mm has been produced by two kinds of different extrudin...The method of manufacturing the composite wire by extruding lead to coated glass fiber is described. The different composite wire that diameter is from 0.5 to 1.0mm has been produced by two kinds of different extruding technology (getting wire along horizontal direction and getting wire along perpendicular direction). The optimal extruding techno- logical parameter has been given in different extruding technology by the physical simulation (H: 300℃, 550kN, 0.16mm. P: 300℃, 215kN, 0.16mm). The effect on the coating speed by other extruding technological parameters in the different extruding technology has been discussed. The extruding temperature and extruding force is higher, the coating speed is faster. It has been pointed, that the affection on the extruding technology by the extruding temperature has also behaved as the extruding temperature rising up spontaneously. The reason for exiting the minimum extruding force and maximum extruding force also has been discussion in this paper. It is also important to the extruding process and coating speed that is the coating clearance.展开更多
The analysis of numerous experimental equations published in the literature reveals awide scatter in the predictions for the static recrystallization kinetics of steels. Thepowers of the deformation variables, strain ...The analysis of numerous experimental equations published in the literature reveals awide scatter in the predictions for the static recrystallization kinetics of steels. Thepowers of the deformation variables, strain and strain rate, similarly as the powerof the grain size vary in these equations. These differences are highlighted and thetypical values are compared between torsion and compression tests. Potential errorsin physical simulation testing are discussed.展开更多
Due to the tremendous amount of high-resolution measurement information,array laterolog is widely used in evaluations of deviated anisotropic reservoirs.However,the precision of a complementary numerical simulation sh...Due to the tremendous amount of high-resolution measurement information,array laterolog is widely used in evaluations of deviated anisotropic reservoirs.However,the precision of a complementary numerical simulation should be improved as high as the core of fine-scale reservoir evaluation.Therefore,the 3D finite element method(3D-FEM)is presented to simulate the array laterolog responses.Notably,a downscaled physical simulation system is introduced to validate and calibrate the precision of the 3D-FEM.First,the size of the downscaled system is determined by COMSOL.Then,the surrounding and investigated beds are represented by a sodium chloride solution and planks soaked in solution,respectively.Finally,a half-space measurement scheme is presented to improve the experimental efficiency.Moreover,the corresponding sensitivity function and separation factor are established to analyze the effects of the formation anisotro py and dipping angle on the array laterolog responses.The numerical and experimental results indicate that the half-space method is practical,and the mean relative error between the numerical and experimental results is less than 5%,which indicates that the numerical simulation is accurate.With the proposed approach,the reversal angle of array laterolog response curves in anisotropic formations can be observed,and this range is determined to be 50°-62°.展开更多
Based on field wave data, an empirical formula of wave envelope spectrum is given in this paper. Then the methods of both numerical and physical simulation of sea wave groups with the given spectrum and groupiness par...Based on field wave data, an empirical formula of wave envelope spectrum is given in this paper. Then the methods of both numerical and physical simulation of sea wave groups with the given spectrum and groupiness parameters are suggested.展开更多
To analyze the overlying strata movement law of recovering room mining standing pillars with solid backfilling.Physical simulation experiments with sponge and wood as the backfilling simulation material were tested.Th...To analyze the overlying strata movement law of recovering room mining standing pillars with solid backfilling.Physical simulation experiments with sponge and wood as the backfilling simulation material were tested.The results show that:(i) The covering-rock mechanics of the overly strata comes from "two-arch structures + hinged girder + bend beam" to "backfilling material + hinged girder + bent beam" by increasing the fill ratio from 0%to 85%,the beginning of overlying strata movement appears later and the total duration of subsidence velocity increased from zero to the highest value increases.The trend of "single polarization" of the subsidence velocity curves becomes noticeable and the velocity variation trend becomes stable,(ii) The equiponderate aeolian sand was added to improve the anti-pressure ability of the loess,and the corresponding ground processing & transportation system was designed.展开更多
A micro-nano pore three-dimensional visualized real-time physical simulation of natural gas charging, in-situ pore-scale computation, pore network modelling, and apparent permeability evaluation theory were used to in...A micro-nano pore three-dimensional visualized real-time physical simulation of natural gas charging, in-situ pore-scale computation, pore network modelling, and apparent permeability evaluation theory were used to investigate laws of gas and water flow and their distribution, and controlling factors during the gas charging process in low-permeability(tight) sandstone reservoir. By describing features of gas-water flow and distribution and their variations in the micro-nano pore system, it is found that the gas charging in the low permeability(tight) sandstone can be divided into two stages, expansion stage and stable stage. In the expansion stage, the gas flows continuously first into large-sized pores then small-sized pores, and first into centers of the pores then edges of pores;pore-throats greater than 20 μm in radius make up the major pathway for gas charging. With the increase of charging pressure, movable water in the edges of large-sized pores and in the centers of small pores is displaced out successively. Pore-throats of 20-50 μm in radius and pore-throats less than 20 μm in radius dominate the expansion of gas charging channels at different stages of charging in turn, leading to reductions in pore-throat radius, throat length and coordination number of the pathway, which is the main increase stage of gas permeability and gas saturation. Among which, pore-throats 30-50 μm in radius control the increase pattern of gas saturation. In the stable stage, gas charging pathways have expanded to the maximum, so the pathways keep stable in pore-throat radius, throat length, and coordination number, and irreducible water remains in the pore system, the gas phase is in concentrated clusters, while the water phase is in the form of dispersed thin film, and the gas saturation and gas permeability tend stable. Connected pore-throats less than 20 μm in radius control the expansion limit of the charging pathways, the formation of stable gas-water distribution, and the maximum gas saturation. The heterogeneity of connected pore-throats affects the dynamic variations of gas phase charging and gas-water distribution. It can be concluded that the pore-throat configuration and heterogeneity of the micro-nanometer pore system control the dynamic variations of the low-permeability(tight) sandstone gas charging process and gas-water distribution features.展开更多
基金funded by the National Natural Science Foundation of China(No.42076069).
文摘The Makran accretionary wedge has the smallest subduction angle among any accretionary prism in the world. The factors controlling the spacing and morphological development of its deep thrust faults, as well as the formation mechanism of shallow normal faults, remain unclear. Meanwhile, the factors affecting the continuity of plane faults must be comprehensively discussed. Clarifying the development characteristics and deformation mechanisms of the Makran accretionary wedge is crucial to effectively guide the exploration of gas hydrate deposits in the area. This study aims to interpret seismic data to identify typical structures in the Makran accretionary wedge, including deep imbricate thrust faults, shallow and small normal faults, wedge-shaped piggyback basins, mud diapirs with fuzzy and disorderly characteristics of reflection, décollements with a northward tilt of 1° – 2°, and large seamounts. Physical simulation-based experiments are performed to comprehensively analyze the results of the plane, section, and slices of the wedge. Results reveal that the distances between and shapes of thrust faults in the deep parts of the Makran accretionary wedge are controlled by the bottom décollement. The uplift of the thrust fault-related folds and the upwelling of the mud diapirs primarily contribute to the formation of small normal faults in the shallow part of the area. The mud diapirs originate from plastic material at the bottom, while those that have developed in the area near the trench are larger. Seamounts and mud diapirs break the continuity of fault plane distribution.
文摘The contrast experiment of different stirring modes,which includes a new type of stirring-injection with the method of pulse and rotation,and the initial one-way stirring method,is done through physical simulation in the laboratory.The stirring methods of pulse and rotation are of two kinds.One is pulsed and rotary stirrer with positive and opposite directions.The other is pulsed and rotary stirrer with rotation-stop-rotation.The results show that the stirring mode of pulse and rotation has better effects than the one-way stirring method.The specific effects are that the mixing time of the melting bath is apparently shortened,the number of grains involved in the liquid surface is increased,and the residence time of air bubble in water is doubled.
基金Acknowledgements This work was financially supported by the National Key Research and Development Program （2016YFC0801402-4）, the National Natural Science Foundation of China （51374236, 51574280）, Chongqing Frontiers and Application- based Research Program （cstc2015jcyjBX0076）. Meanwhile, the author would like to thank the reviewers of this paper for their constructive comments and suggestions to improve the publication.
文摘Coal and gas outburst is one of the main gas hazards in coal mines. However, due to the risks of the coal and gas outburst, the field test is difficult to complete. Therefore, an effective approach to studying the mechanism and development of outburst is to conduct the similar physical simulation. However, the similarity criteria and similar materials in outburst are the key factors which restrict the development of physical simulation. To solve those problems, this paper has established similarity criteria base on mechanics model, solid-fluid coupling model and energy model, and presented high similar materials. Combining with three groups of similar number, and considering similar mechanical parameters and deformation and failure regularity, the similarity criteria of outburst is determined on the basis of the energy model. According to those criteria, we put forward a similar material consists of pulverized coal, cement, sand, activated carbon, and water. The similar material has high compressive strength and the accordant characteristics with the raw coal, include density, porosity, adsorption, desorption. The new research is promising for preventing and controlling gas hazards in the future.
文摘The kinetics of ε-Cu particles dissolution in the matrix during welding of a copper-precipitation strengthening steel was determined by a combination of GleebleTM physical simulation, TEM examination and hardness meas urement. The ε-Cu particles underwent a coarsening and part dissolution and then complete dissolution reaction as the peak temperature increased from 750 to 1 000℃, which resulted in the decrease in the number density of ε-Cu particles and hardness in the heat affected zone （HAZ）. The results can be used to understand the evolution of this transformation and a softening behavior of the HAZ during welding of this type of steel.
基金supported by the National Key R&D Program of China(Grant No.2018YFC1405900)the Major Projects of National Science and Technology(Grant Nos.2016ZX05011-002,2016ZX05027-002-005)+3 种基金the National Natural Science Foundation of China(Grant No.41806073)the Natural Science Foundation of Shandong Province(Grant No.ZR2017BD014)Shandong Provincial Key Laboratory of Depositional Mineralization and Sedimentary Minerals,Shandong University of Science and Technology(Grant No.DMSM2017042)the Fundamental Research Funds for the Central Universities(Grant No.201964016)
文摘To establish the relationship among reservoir characteristics and rock physical parameters,we construct the well-bore rock physical models firstly,considering the influence factors,such as mineral composition,shale content,porosity,fluid type and saturation.Then with analyzing the change rules of elastic parameters along with the above influence factors and the cross-plots among elastic parameters,the sensitive elastic parameters of tight sandstone reservoir are determined,and the rock physics template of sweet spot is constructed to guide pre-stack seismic inversion.The results show that velocity ratio and Poisson impedance are the most sensitive elastic parameters to indicate the lithologic and gas-bearing properties of sweet spot in tight sandstone reservoir.The high-quality sweet spot is characterized by the lower velocity ratio and Poisson impedance.Finally,the actual seismic data are selected to predict the sweet spots in tight sandstone gas reservoirs,so as to verify the validity of the rock physical simulation results.The significant consistency between the relative logging curves and inversion results in different wells implies that the utilization of well-bore rock physical simulation can guide the prediction of sweet spot in tight sandstone gas reservoirs.
文摘Mold-filling process of thin-walled castings under the condition of traveling magnetic field has been studied by physical simulation method using gallium melt and fast speed photography. Flow morphology and its formation mechanism were obtained and discussed for thin-walled casting. The influences of magnetic field density on the filling ability, filling velocity and mold filling time have been studied. The differences in filling capability between gravity casting and casting under the traveling magnetic field have been compared. The results indicate that the mold filling ability of the gallium melt increases greatly under the condition of traveling magnetic field; the filling time is shortened from 18 s under gravity field to 3 s under the traveling magnetic field and average flow rate of the melt increases from 1.6 to 8.68 cm3/s; the change law of the cross-section morphology of the gallium melt during the mold filling is that at first, the cross-section area does not change, then it decreases gradually. When the front of the melt reaches the end of the mold cavity, the front melt will backfill the mold; the wider the width of mold cavity, the better the mold filling ability. The mold filling ability of gallium melt in mold with upper magnetic conductor is better than that without upper magnetic conductor.
基金Projects 50490270 and 50634050 supported by the National Natural Science Foundation of China2007CB209400 by the National Basic Research Program of China2006A039 by the Youth Scientific Research Foundation of China University of Mining & Technology
文摘The behavior of stress wave propagation in rock walls and the process of rock bursts were simulated by application tests of material similar to rock. Results show that 1) the attenuation characteristics of stress waves were related to the material proper-ties, stress waves attenuate more quickly in soft material and 2) when the explosion load was applied at the top of the roadway, the number and the length of the cracks increased with a decrease in the distance between the explosive point and roof of the roadway. When the distance was 280 mm, only some chips appeared near the source, when the distance was 210 mm, some small cracks started to appear near the road-rib and when the distance was reduced to 140 mm, larger cracks appeared at the road-rib. It can be concluded that, under a given stress the number of cracks is closely related to the intensity of stress waves. The cracks in the sur-rounding rock can be reduced by controlling the intensity of the stress waves and rock bursts can be avoided to some extent by pre-venting the formation of layered crack structures. A new experimental approach has been provided for studying rock bursts by using physical simulation.
文摘Direct quenching and tempering （DQ-T） of hot rolled steel section has been widely used in steel mill for the sake of improvement of mechanical properties and energy saving. Temperature history and microstructural evolution during hot rolling plays a major role in the properties of direct quenched and tempered products. The mathematical and physical modeling of hot forming processes is becoming a very important tool for design and development of required products as well as predicting the microstructure and the properties of the components. These models were mostly used to predict austenite grain size （AGS）, dynamic, recta-dynamic and static recrystallization in the rods immediately after hot rolling and prior to DQ process. The hot compression tests were carried out on 42CrMo4 steel in the temperature range of 900-1 100 ℃ and the strain rate range of 0. 05-1 s^-1 in order to study the high tempera- ture softening behavior of the steel. For the exact prediction of flow stress, the effective stress-effective strain curves were obtained from experiments under various conditions. On the basis of experimental results, the dynamic recrystallization fraction （DRX）, AGS, hot deformation and activation energy behavior were investigated. It was found that the calculated results were in good agreement with the experimental flow stress and microstructure of the steel for different conditions of hot deformation.
基金supported by National Natural Science Fundation of China (Grant No. 40772176)Key Program for Research Group of SKLGP (Grant No. SKLGP2009Z002)Research Fund for the Doctoral Program of Higher Education of China(Grant No. 20105122110008)
文摘According to the test results of the physical and mechanical properties of similar materials in various quality mixture, a type of material with obvious tendency of rockburst was selected to produce a large-size model to simulate rockburst phenomena in tunnels. The prototype model comes from a typical section of diversion tunnels in Jinping Hydropower Station in China. The simulation of excavating tunnels is carried out by opening a hole in the model after loading. The modeling results indicated that under the condition of normal stresses in the model boundaries the arch top, spandrel and side walls of the tunnel produced an obvious jump reaction of stress and strain and the acoustic emission counts of the surrounding rock also increased rapidly in a different time period after the "tunnel" excavation, showing the clear features of rockburst. The spalling, buckling and breaking occurred in the surrounding rock of model in conditions of over loading. It is concluded that the modeling tunnel segment in Jinping Hydropower Station is expected to form the tensile rockburst with the pattern of spalling, buckling and breaking.
基金supported by the National Natural Science Foundation of China(U1508217,U1702253 and 51774078)the Fundamental Research Funds for the Central Universities(N172506009 and N170908001).
文摘In order to increase the contact area and promote the mass transfer process of gas and liquid,the process of the bubble refine-ment in a metallurgical reactor with mechanical agitation was studied by physical simulation.Based on the capillary number,a prediction equation for the bubble refinement was established.The effects of the gas flow rate,the stirring speed and thestirring depth on the bubble refinement in the reactor were discussed in detail.The distribution of the bubble diameter in thereactor was obtained under different conditions.The results show that when the stirring speed reaches 300 r/min,the bubblediamcter mainly distributes in the range of 1-2 mm.A higher gas flow rate may increase the number of bubbles in the meltand promote the bubble refinement process.The mechanism of bubble refinement under mechanical agitation was analyzed.and the results indicated that the stirring speed.,the blade area and the blade inclination are the main influencing factors.
基金Project 2002CB211705 supported by the National Basic Research Program of China
文摘In order to select highly productive and enriched areas of high rank coalbed methane reservoirs, based on hydrologic geology as one of the main factors controlling coalbed methane （CBM） reservoir formations, the effect of hydrodynamic forces controlling CBM reservoir formations was studied by a physical simulation experiment in which we used CBM reservoir simulation facilities. The hydrodynamic conditions of high coal rank reservoirs in the Qinshui basin were analyzed. Our experiment shows the following results： under strong hydrodynamic alternating action, 6C~ of coalbed methane reservoir changed from the start at -2.95% ~ -3.66%, and the lightening process occurred in phases; the CI-I4 volume reduced from 96.35% to 12.42%; the CO2 vo- lume decreased from 0.75% in sample 1 to 0.68% in sample 2, then rose to 1.13% in sample 3; the N2 volume changed from 2.9% in sample 1 to 86.45% in sample 3. On one hand, these changes show the complexity of CBM reservoir formation; on the other hand, they indicate that strong hydrodynamic actions have an unfavorable impact on CBM reservoir formation. It was found that the gas volume and hydrodynamic intensity were negatively correlated and low hydrodynamic flow conditions might result in highly productive and enriched areas of high rank CBM.
基金supported by the National Natural Science Foundation of China (Grant Nos. 51079023 and 50921001)the Program for New Century Excellent Talents in University (Grant No. NCET-05-0282)
文摘Real waves are multidirectional waves. In the present study, the calculation method for the wave maker driving signals for generating multidirectional wave groups in physical wave basin is proposed. Its validity is first confirmed by a numerical model for which the incident boundary condition is determined by use of the proposed method. Then, the physical simulation of multidirectional wave groups is performed in laboratory wave basin. The experimental results show that multidirectional waves with expected wave groupiness, which includes not only its group height but also its group length, can be satisfactorily zenerated at the soecified oosition in the tphvsical wave basin.
基金Supported by National Natural Science Foundation of China(51475418)National Basic Research 973 Program of China(2011CB706503)Science Fund for Creative Research Groups of National Natural Science Foundation of China(51221004)
文摘Most existing force feedback methods are still difficult to meet the requirements of real-time force calculation in virtual assembly and operation with complex objects. In addition, there is often an assumption that the controlled objects are completely flee and the target object is only completely fixed or flee, thus, the dynamics of the kinematic chain where the controlled objects are located are neglected during the physical simulation of the product manipulation with force feedback interaction. This paper proposes a physical simulation method of product assembly and operation manipulation based on statistically learned contact force prediction model and the coupling of force feedback and dynamics. In the proposed method, based on hidden Markov model （HMM） and local weighting learning （LWL）, contact force prediction model is constructed, which can estimate the contact force in real time during interaction. Based on computational load balance model, the computing resources are dynamically assigned and the dynamics integral step is optimized. In addition, smoothing process is performed to the force feedback on the synchronization points. Consequently, we can solve the coupling and synchronization problems of high-frequency feedback force servo. low-frequency dynamics solver servo and scene rendering servo, and realize highly stable and accurate force feedback in the physical simulation of product assembly and operation manipulation. This research proposes a physical simulation method of product assembly and operation manipulation.
基金supported by China National Program on Key Basic Research Project (973 Program) (Grant No. 2006CB705805)National Key Scientific and Technological Project (Grant No. 2008ZX05009-004)
文摘For extra-low permeability reservoirs, with a permeability of about 0.3×10?3 μm2, fluid flow and production performance in cores were studied. A long core holder with a multi-location piezometric measurement was specially designed. An artificial long core, about 700 mm long and with a cross section of 45mm×45mm, was used. In the experiment, pressure distribution along the core can be measured in real time. Single phase flow in the core was investigated. Different modes of production in long cores were also simulated including natural depletion, water flooding, and advanced water flooding. Through physical simulation, flow parameters were collected and production characteristics in extra-low permeability cores were studied. From experimental results, it can be seen that fluid flow in extra-low permeability cores is different from that in high permeability cores. Transmission of pressure in extra-low permeability cores is very slow, and it needs a long time for the pressure to become stable. The distribution curve of pressure along the core is nonlinear and the production rate in extra-low permeability reservoirs decreases sharply. The development effects of different production modes in extra-low permeability cores were compared with one another. Among the production modes, advanced water flooding has much potential for effective development of extra-low permeability reservoirs. Natural depletion and conventional water flooding can also be used in early production periods. In addition, the countermeasures and some ideas especially for the potential development of extra-low permeability reservoirs are suggested.
文摘The method of manufacturing the composite wire by extruding lead to coated glass fiber is described. The different composite wire that diameter is from 0.5 to 1.0mm has been produced by two kinds of different extruding technology (getting wire along horizontal direction and getting wire along perpendicular direction). The optimal extruding techno- logical parameter has been given in different extruding technology by the physical simulation (H: 300℃, 550kN, 0.16mm. P: 300℃, 215kN, 0.16mm). The effect on the coating speed by other extruding technological parameters in the different extruding technology has been discussed. The extruding temperature and extruding force is higher, the coating speed is faster. It has been pointed, that the affection on the extruding technology by the extruding temperature has also behaved as the extruding temperature rising up spontaneously. The reason for exiting the minimum extruding force and maximum extruding force also has been discussion in this paper. It is also important to the extruding process and coating speed that is the coating clearance.
文摘The analysis of numerous experimental equations published in the literature reveals awide scatter in the predictions for the static recrystallization kinetics of steels. Thepowers of the deformation variables, strain and strain rate, similarly as the powerof the grain size vary in these equations. These differences are highlighted and thetypical values are compared between torsion and compression tests. Potential errorsin physical simulation testing are discussed.
基金funded by the National Natural Science Foundation of China(41974146,42074134)the Graduate Innovation Project of China University of Petroleum(East China)(YCX2021005)。
文摘Due to the tremendous amount of high-resolution measurement information,array laterolog is widely used in evaluations of deviated anisotropic reservoirs.However,the precision of a complementary numerical simulation should be improved as high as the core of fine-scale reservoir evaluation.Therefore,the 3D finite element method(3D-FEM)is presented to simulate the array laterolog responses.Notably,a downscaled physical simulation system is introduced to validate and calibrate the precision of the 3D-FEM.First,the size of the downscaled system is determined by COMSOL.Then,the surrounding and investigated beds are represented by a sodium chloride solution and planks soaked in solution,respectively.Finally,a half-space measurement scheme is presented to improve the experimental efficiency.Moreover,the corresponding sensitivity function and separation factor are established to analyze the effects of the formation anisotro py and dipping angle on the array laterolog responses.The numerical and experimental results indicate that the half-space method is practical,and the mean relative error between the numerical and experimental results is less than 5%,which indicates that the numerical simulation is accurate.With the proposed approach,the reversal angle of array laterolog response curves in anisotropic formations can be observed,and this range is determined to be 50°-62°.
文摘Based on field wave data, an empirical formula of wave envelope spectrum is given in this paper. Then the methods of both numerical and physical simulation of sea wave groups with the given spectrum and groupiness parameters are suggested.
基金provided by the National Natural Science Foundation of China(No.51074165)the NationalKey Basic Research Program of China(No.2013CB227905)the Qing-Lan Project of China Scholarship Council
文摘To analyze the overlying strata movement law of recovering room mining standing pillars with solid backfilling.Physical simulation experiments with sponge and wood as the backfilling simulation material were tested.The results show that:(i) The covering-rock mechanics of the overly strata comes from "two-arch structures + hinged girder + bend beam" to "backfilling material + hinged girder + bent beam" by increasing the fill ratio from 0%to 85%,the beginning of overlying strata movement appears later and the total duration of subsidence velocity increased from zero to the highest value increases.The trend of "single polarization" of the subsidence velocity curves becomes noticeable and the velocity variation trend becomes stable,(ii) The equiponderate aeolian sand was added to improve the anti-pressure ability of the loess,and the corresponding ground processing & transportation system was designed.
基金Supported by the National Natural Science Foundation of China (41330319 and 42072174)Foundation of China University of Petroleum Beijing (2462020XKBH016)Fellowship of China Postdoctoral Science Foundation (2020M680030)。
文摘A micro-nano pore three-dimensional visualized real-time physical simulation of natural gas charging, in-situ pore-scale computation, pore network modelling, and apparent permeability evaluation theory were used to investigate laws of gas and water flow and their distribution, and controlling factors during the gas charging process in low-permeability(tight) sandstone reservoir. By describing features of gas-water flow and distribution and their variations in the micro-nano pore system, it is found that the gas charging in the low permeability(tight) sandstone can be divided into two stages, expansion stage and stable stage. In the expansion stage, the gas flows continuously first into large-sized pores then small-sized pores, and first into centers of the pores then edges of pores;pore-throats greater than 20 μm in radius make up the major pathway for gas charging. With the increase of charging pressure, movable water in the edges of large-sized pores and in the centers of small pores is displaced out successively. Pore-throats of 20-50 μm in radius and pore-throats less than 20 μm in radius dominate the expansion of gas charging channels at different stages of charging in turn, leading to reductions in pore-throat radius, throat length and coordination number of the pathway, which is the main increase stage of gas permeability and gas saturation. Among which, pore-throats 30-50 μm in radius control the increase pattern of gas saturation. In the stable stage, gas charging pathways have expanded to the maximum, so the pathways keep stable in pore-throat radius, throat length, and coordination number, and irreducible water remains in the pore system, the gas phase is in concentrated clusters, while the water phase is in the form of dispersed thin film, and the gas saturation and gas permeability tend stable. Connected pore-throats less than 20 μm in radius control the expansion limit of the charging pathways, the formation of stable gas-water distribution, and the maximum gas saturation. The heterogeneity of connected pore-throats affects the dynamic variations of gas phase charging and gas-water distribution. It can be concluded that the pore-throat configuration and heterogeneity of the micro-nanometer pore system control the dynamic variations of the low-permeability(tight) sandstone gas charging process and gas-water distribution features.
