The frontal edge of the Makran accretionary wedge is characterized by the development of multiple imbricate thrust faults trending E-W and relatively parallel.However,the mechanisms underlying their formation and the ...The frontal edge of the Makran accretionary wedge is characterized by the development of multiple imbricate thrust faults trending E-W and relatively parallel.However,the mechanisms underlying their formation and the factors controlling their development remain subjects of debate.This paper,based on seismic profile analysis,employs physical simulation experiments to establish a'wedge'type subduction model.The study explores the influence of the initial wedge angle,horizontal sand layer thickness,and the presence or absence of a decollement layer on the structural styles of the thrust wedge.Experimental results indicate that as the initial wedge angle decreases from 11°to 8°,the lateral growth of the thrust wedge increases,whereas vertical growth diminishes.When the horizontal sand layer thickness is reduced from 4.5 cm to 3.0 cm,the spacing between the frontal thrusts decreases and the number of thrust faults increases.Both lateral and vertical growth are relatively reduced,resulting in a smaller thrust wedge.When a decollement layer is present,the structural style exhibits layered deformation.The decollement layer constrains the development of back thrusts and promotes the localized formation of frontal thrusts.In conclusion,the imbricate thrust faults at the frontal edge of the Makran accretionary wedge are primarily controlled by the characteristics of the wedge itself and the presence of the decollement layer.展开更多
In the ultra-deep strata of the Tarim Basin,the vertical growth process of strike-slip faults remains unclear,and the vertical distribution of fractured-cavity carbonate reservoirs is complex.This paper investigates t...In the ultra-deep strata of the Tarim Basin,the vertical growth process of strike-slip faults remains unclear,and the vertical distribution of fractured-cavity carbonate reservoirs is complex.This paper investigates the vertical growth process of strike-slip faults through field outcrop observations in the Keping area,interpretation of seismic data from the Fuman Oilfield,Tarim Basim,NW China,and structural physical simulation experiments.The results are obtained mainly in four aspects.First,field outcrops and ultra-deep seismic profiles indicate a three-layer structure within the strike-slip fault,consisting of fault core,fracture zone and primary rock.The fault core can be classified into three parts vertically:fracture-cavity unit,fault clay and breccia zone.The distribution of fracture-cavity units demonstrates a distinct pattern of vertical stratification,owing to the structural characteristics and growth process of the slip-strike fault.Second,the ultra-deep seismic profiles show multiple fracture-cavity units in the strike-slip fault zone.These units can be classified into four types:top fractured,middle connected,deep terminated,and intra-layer fractured.Third,structural physical simulation experiments and ultra-deep seismic data interpretation reveal that the strike-slip faults have evolved vertically in three stages:segmental rupture,vertical growth,and connection and extension.The particle image velocimetry detection demonstrates that the initial fracture of the fault zone occurred at the top or bottom and then evolved into cavities gradually along with the fault growth,accompanied by the emergence of new fractures in the middle part of the strata,which subsequently connected with the deep and shallow cavities to form a complete fault zone.Fourth,the ultra-deep carbonate strata primarily develop three types of fractured-cavity reservoirs:flower-shaped fracture,large and deep fault and staggered overlap.The first two types are larger in size with better reservoir conditions,suggesting a significant exploration potential.展开更多
The hot forging of large-scale P/M TiAl alloy billet deformation was investigated based on a joint application of Deform-3D-based numerical simulation and physical simulation techniques.The temperature dependence on t...The hot forging of large-scale P/M TiAl alloy billet deformation was investigated based on a joint application of Deform-3D-based numerical simulation and physical simulation techniques.The temperature dependence on the thermal and mechanical properties of the billet was considered and the optimum hot working temperature of packed TiAl alloy was 1150-1200 °C.Based on the simulation,the material flow and thermo mechanical field variables,such as stress,strain,and temperature distribution were obtained and the relationships of load—displacement and load—time were figured out.To verify the validity of the simulation results,the experiments were also carried out in a forging plant,and a pancake with diameter of 150 mm was obtained exhibiting a regular shape.展开更多
The contrast experiment of different stirring modes,which includes a new type of stirring-injection with the method of pulse and rotation,and the initial one-way stirring method,is done through physical simulation in ...The contrast experiment of different stirring modes,which includes a new type of stirring-injection with the method of pulse and rotation,and the initial one-way stirring method,is done through physical simulation in the laboratory.The stirring methods of pulse and rotation are of two kinds.One is pulsed and rotary stirrer with positive and opposite directions.The other is pulsed and rotary stirrer with rotation-stop-rotation.The results show that the stirring mode of pulse and rotation has better effects than the one-way stirring method.The specific effects are that the mixing time of the melting bath is apparently shortened,the number of grains involved in the liquid surface is increased,and the residence time of air bubble in water is doubled.展开更多
Coal and gas outburst is one of the main gas hazards in coal mines. However, due to the risks of the coal and gas outburst, the field test is difficult to complete. Therefore, an effective approach to studying the mec...Coal and gas outburst is one of the main gas hazards in coal mines. However, due to the risks of the coal and gas outburst, the field test is difficult to complete. Therefore, an effective approach to studying the mechanism and development of outburst is to conduct the similar physical simulation. However, the similarity criteria and similar materials in outburst are the key factors which restrict the development of physical simulation. To solve those problems, this paper has established similarity criteria base on mechanics model, solid-fluid coupling model and energy model, and presented high similar materials. Combining with three groups of similar number, and considering similar mechanical parameters and deformation and failure regularity, the similarity criteria of outburst is determined on the basis of the energy model. According to those criteria, we put forward a similar material consists of pulverized coal, cement, sand, activated carbon, and water. The similar material has high compressive strength and the accordant characteristics with the raw coal, include density, porosity, adsorption, desorption. The new research is promising for preventing and controlling gas hazards in the future.展开更多
The kinetics of ε-Cu particles dissolution in the matrix during welding of a copper-precipitation strengthening steel was determined by a combination of GleebleTM physical simulation, TEM examination and hardness mea...The kinetics of ε-Cu particles dissolution in the matrix during welding of a copper-precipitation strengthening steel was determined by a combination of GleebleTM physical simulation, TEM examination and hardness meas urement. The ε-Cu particles underwent a coarsening and part dissolution and then complete dissolution reaction as the peak temperature increased from 750 to 1 000℃, which resulted in the decrease in the number density of ε-Cu particles and hardness in the heat affected zone （HAZ）. The results can be used to understand the evolution of this transformation and a softening behavior of the HAZ during welding of this type of steel.展开更多
To establish the relationship among reservoir characteristics and rock physical parameters,we construct the well-bore rock physical models firstly,considering the influence factors,such as mineral composition,shale co...To establish the relationship among reservoir characteristics and rock physical parameters,we construct the well-bore rock physical models firstly,considering the influence factors,such as mineral composition,shale content,porosity,fluid type and saturation.Then with analyzing the change rules of elastic parameters along with the above influence factors and the cross-plots among elastic parameters,the sensitive elastic parameters of tight sandstone reservoir are determined,and the rock physics template of sweet spot is constructed to guide pre-stack seismic inversion.The results show that velocity ratio and Poisson impedance are the most sensitive elastic parameters to indicate the lithologic and gas-bearing properties of sweet spot in tight sandstone reservoir.The high-quality sweet spot is characterized by the lower velocity ratio and Poisson impedance.Finally,the actual seismic data are selected to predict the sweet spots in tight sandstone gas reservoirs,so as to verify the validity of the rock physical simulation results.The significant consistency between the relative logging curves and inversion results in different wells implies that the utilization of well-bore rock physical simulation can guide the prediction of sweet spot in tight sandstone gas reservoirs.展开更多
Mold-filling process of thin-walled castings under the condition of traveling magnetic field has been studied by physical simulation method using gallium melt and fast speed photography. Flow morphology and its format...Mold-filling process of thin-walled castings under the condition of traveling magnetic field has been studied by physical simulation method using gallium melt and fast speed photography. Flow morphology and its formation mechanism were obtained and discussed for thin-walled casting. The influences of magnetic field density on the filling ability, filling velocity and mold filling time have been studied. The differences in filling capability between gravity casting and casting under the traveling magnetic field have been compared. The results indicate that the mold filling ability of the gallium melt increases greatly under the condition of traveling magnetic field; the filling time is shortened from 18 s under gravity field to 3 s under the traveling magnetic field and average flow rate of the melt increases from 1.6 to 8.68 cm3/s; the change law of the cross-section morphology of the gallium melt during the mold filling is that at first, the cross-section area does not change, then it decreases gradually. When the front of the melt reaches the end of the mold cavity, the front melt will backfill the mold; the wider the width of mold cavity, the better the mold filling ability. The mold filling ability of gallium melt in mold with upper magnetic conductor is better than that without upper magnetic conductor.展开更多
Direct quenching and tempering （DQ-T） of hot rolled steel section has been widely used in steel mill for the sake of improvement of mechanical properties and energy saving. Temperature history and microstructural ev...Direct quenching and tempering （DQ-T） of hot rolled steel section has been widely used in steel mill for the sake of improvement of mechanical properties and energy saving. Temperature history and microstructural evolution during hot rolling plays a major role in the properties of direct quenched and tempered products. The mathematical and physical modeling of hot forming processes is becoming a very important tool for design and development of required products as well as predicting the microstructure and the properties of the components. These models were mostly used to predict austenite grain size （AGS）, dynamic, recta-dynamic and static recrystallization in the rods immediately after hot rolling and prior to DQ process. The hot compression tests were carried out on 42CrMo4 steel in the temperature range of 900-1 100 ℃ and the strain rate range of 0. 05-1 s^-1 in order to study the high tempera- ture softening behavior of the steel. For the exact prediction of flow stress, the effective stress-effective strain curves were obtained from experiments under various conditions. On the basis of experimental results, the dynamic recrystallization fraction （DRX）, AGS, hot deformation and activation energy behavior were investigated. It was found that the calculated results were in good agreement with the experimental flow stress and microstructure of the steel for different conditions of hot deformation.展开更多
The behavior of stress wave propagation in rock walls and the process of rock bursts were simulated by application tests of material similar to rock. Results show that 1) the attenuation characteristics of stress wave...The behavior of stress wave propagation in rock walls and the process of rock bursts were simulated by application tests of material similar to rock. Results show that 1) the attenuation characteristics of stress waves were related to the material proper-ties, stress waves attenuate more quickly in soft material and 2) when the explosion load was applied at the top of the roadway, the number and the length of the cracks increased with a decrease in the distance between the explosive point and roof of the roadway. When the distance was 280 mm, only some chips appeared near the source, when the distance was 210 mm, some small cracks started to appear near the road-rib and when the distance was reduced to 140 mm, larger cracks appeared at the road-rib. It can be concluded that, under a given stress the number of cracks is closely related to the intensity of stress waves. The cracks in the sur-rounding rock can be reduced by controlling the intensity of the stress waves and rock bursts can be avoided to some extent by pre-venting the formation of layered crack structures. A new experimental approach has been provided for studying rock bursts by using physical simulation.展开更多
In order to select highly productive and enriched areas of high rank coalbed methane reservoirs, based on hydrologic geology as one of the main factors controlling coalbed methane （CBM） reservoir formations, the eff...In order to select highly productive and enriched areas of high rank coalbed methane reservoirs, based on hydrologic geology as one of the main factors controlling coalbed methane （CBM） reservoir formations, the effect of hydrodynamic forces controlling CBM reservoir formations was studied by a physical simulation experiment in which we used CBM reservoir simulation facilities. The hydrodynamic conditions of high coal rank reservoirs in the Qinshui basin were analyzed. Our experiment shows the following results： under strong hydrodynamic alternating action, 6C~ of coalbed methane reservoir changed from the start at -2.95% ~ -3.66%, and the lightening process occurred in phases; the CI-I4 volume reduced from 96.35% to 12.42%; the CO2 vo- lume decreased from 0.75% in sample 1 to 0.68% in sample 2, then rose to 1.13% in sample 3; the N2 volume changed from 2.9% in sample 1 to 86.45% in sample 3. On one hand, these changes show the complexity of CBM reservoir formation; on the other hand, they indicate that strong hydrodynamic actions have an unfavorable impact on CBM reservoir formation. It was found that the gas volume and hydrodynamic intensity were negatively correlated and low hydrodynamic flow conditions might result in highly productive and enriched areas of high rank CBM.展开更多
According to the test results of the physical and mechanical properties of similar materials in various quality mixture, a type of material with obvious tendency of rockburst was selected to produce a large-size model...According to the test results of the physical and mechanical properties of similar materials in various quality mixture, a type of material with obvious tendency of rockburst was selected to produce a large-size model to simulate rockburst phenomena in tunnels. The prototype model comes from a typical section of diversion tunnels in Jinping Hydropower Station in China. The simulation of excavating tunnels is carried out by opening a hole in the model after loading. The modeling results indicated that under the condition of normal stresses in the model boundaries the arch top, spandrel and side walls of the tunnel produced an obvious jump reaction of stress and strain and the acoustic emission counts of the surrounding rock also increased rapidly in a different time period after the "tunnel" excavation, showing the clear features of rockburst. The spalling, buckling and breaking occurred in the surrounding rock of model in conditions of over loading. It is concluded that the modeling tunnel segment in Jinping Hydropower Station is expected to form the tensile rockburst with the pattern of spalling, buckling and breaking.展开更多
A new physical simulation model was developed to simulate the casting process of the ductile iron heavy section spent-nuclear-fuel container.In this physical simulation model,a heating unit with DR24 Fe-Cr-Al heating ...A new physical simulation model was developed to simulate the casting process of the ductile iron heavy section spent-nuclear-fuel container.In this physical simulation model,a heating unit with DR24 Fe-Cr-Al heating wires was used to compensate the heat loss across the non-natural surfaces of the sample,and a precise and reliable casting temperature controlling/monitoring system was employed to ensure the thermal behavior of the simulated casting to be similar to the actual casting.Also,a mould system was designed,in which changeable mould materials can be used for both the outside and inside moulds for different applications.The casting test was carried out with the designed mould and the cooling curves of central and edge points at different isothermal planes of the casting were obtained.Results show that for most isothermal planes,the temperature control system can keep the temperature differences within 6 ℃ between the edge points and the corresponding center points,indicating that this new physical simulation model has high simulation accuracy,and the mould developed can be used for optimization of casting parameters of spent-nuclear-fuel container,such as composition of ductile iron,the pouring temperature,the selection of mould material and design of cooling system.In addition,to maintain the spheroidalization of the ductile iron,the force-chilling should be used for the current physical simulation to ensure the solidification of casting in less than 2 h.展开更多
High-steep slope stability and its optimal excavation design in Shuichang open pit iron mine were analyzed based on a large 3D physical simulation technique. An optimal excavation scheme with a relatively steeper slop...High-steep slope stability and its optimal excavation design in Shuichang open pit iron mine were analyzed based on a large 3D physical simulation technique. An optimal excavation scheme with a relatively steeper slope angle was successfully implemented at the northwest wall between Nos. 4 and 5 exploration lines of Shuichang Iron Mine, taking into account the 3D scale effect. The phys-ico-mechanical properties of rock materials were obtained by laboratory tests conducted on sample cores from exploration drilling directly from the iron mine. A porous rock-like composite material was formed for the model, and the mechanical parameters of the material were assessed experimentally;specifically, the effect of water on the sample was quantitatively determined. We adopted an experimental setup using stiff modular applied static loading to carry out a visual excavation of the slope at a random depth. The setup was equipped with acous-tic emission （AE） sensors, and the experiments were monitored by crack optical acquirement, ground penetrating radar, and close-field pho-togrammetry to investigate the mechanisms of rock-mass destabilization in the high-steep slope. For the complex study area, the model re-sults indicated a clear correlation between the model＇s destabilization resulting from slope excavation and the collected monitoring informa-tion. During the model simulation, the overall angle of the slope increased by 1-6 degrees in different sections. Dramatically, the modeled excavation scheme saved over 80 million tons of rock from extraction, generating enormous economic and ecological benefits.展开更多
In order to increase the contact area and promote the mass transfer process of gas and liquid,the process of the bubble refine-ment in a metallurgical reactor with mechanical agitation was studied by physical simulati...In order to increase the contact area and promote the mass transfer process of gas and liquid,the process of the bubble refine-ment in a metallurgical reactor with mechanical agitation was studied by physical simulation.Based on the capillary number,a prediction equation for the bubble refinement was established.The effects of the gas flow rate,the stirring speed and thestirring depth on the bubble refinement in the reactor were discussed in detail.The distribution of the bubble diameter in thereactor was obtained under different conditions.The results show that when the stirring speed reaches 300 r/min,the bubblediamcter mainly distributes in the range of 1-2 mm.A higher gas flow rate may increase the number of bubbles in the meltand promote the bubble refinement process.The mechanism of bubble refinement under mechanical agitation was analyzed.and the results indicated that the stirring speed.,the blade area and the blade inclination are the main influencing factors.展开更多
Real waves are multidirectional waves. In the present study, the calculation method for the wave maker driving signals for generating multidirectional wave groups in physical wave basin is proposed. Its validity is fi...Real waves are multidirectional waves. In the present study, the calculation method for the wave maker driving signals for generating multidirectional wave groups in physical wave basin is proposed. Its validity is first confirmed by a numerical model for which the incident boundary condition is determined by use of the proposed method. Then, the physical simulation of multidirectional wave groups is performed in laboratory wave basin. The experimental results show that multidirectional waves with expected wave groupiness, which includes not only its group height but also its group length, can be satisfactorily zenerated at the soecified oosition in the tphvsical wave basin.展开更多
In order to understand the mechanism of air flooding shale oil, an online physical simulation method for enhanced shale oil recovery by air injection was established by integrating CT scanning and nuclear magnetic res...In order to understand the mechanism of air flooding shale oil, an online physical simulation method for enhanced shale oil recovery by air injection was established by integrating CT scanning and nuclear magnetic resonance(NMR). The development effect of shale oil by air flooding under different depletion pressures, the micro-production characteristics of pore throats with different sizes and the mechanism of shale oil recovery by air flooding were analyzed. The effects of air oxygen content, permeability, gas injection pressure, and fractures on the air flooding effect in shale and crude oil production in pores with different sizes were analyzed. The recovery of shale oil can be greatly improved by injecting air into the depleted shale reservoir, but the oil displacement efficiency and the production degree of different levels of pore throats vary with the injection timing. The higher the air oxygen content and the stronger the low-temperature oxidation, the higher the production degree of pores with different sizes and the higher the shale oil recovery. The higher the permeability and the better the pore throat connectivity, the stronger the fluid flow capacity and the higher the shale oil recovery. As the injection pressure increases, the lower limit of the production degree of pore throats decreases, but gas channeling may occur to cause a premature breakthrough;as a result, the recovery increases and then decreases. Fractures can effectively increase the contact area between gas and crude oil, and increase the air sweep coefficient and matrix oil drainage area by supplying oil to fractures through the matrix, which means that a proper fracturing before air injection can help to improve the oil displacement effect under a reasonable production pressure difference.展开更多
Realistic modeling and rendering of dynamic tornado scene is recognized as a challenging task for researchers of computer graphics. In this paper a new physically based method for simulating and animating tornado scen...Realistic modeling and rendering of dynamic tornado scene is recognized as a challenging task for researchers of computer graphics. In this paper a new physically based method for simulating and animating tornado scene is presented. We first propose a Two-Fluid model based on the physical theory of tornado, then we simulate the flow of tornado and its interaction with surrounding objects such as debris, etc. Taking the scattering and absorption of light by the participating media into account, the illumination effects of the tornado scene can be generated realistically. With the support of graphics hardware, various kinds of dynamic tornado scenes can be rendered at interactive rates.展开更多
Most existing force feedback methods are still difficult to meet the requirements of real-time force calculation in virtual assembly and operation with complex objects. In addition, there is often an assumption that t...Most existing force feedback methods are still difficult to meet the requirements of real-time force calculation in virtual assembly and operation with complex objects. In addition, there is often an assumption that the controlled objects are completely flee and the target object is only completely fixed or flee, thus, the dynamics of the kinematic chain where the controlled objects are located are neglected during the physical simulation of the product manipulation with force feedback interaction. This paper proposes a physical simulation method of product assembly and operation manipulation based on statistically learned contact force prediction model and the coupling of force feedback and dynamics. In the proposed method, based on hidden Markov model （HMM） and local weighting learning （LWL）, contact force prediction model is constructed, which can estimate the contact force in real time during interaction. Based on computational load balance model, the computing resources are dynamically assigned and the dynamics integral step is optimized. In addition, smoothing process is performed to the force feedback on the synchronization points. Consequently, we can solve the coupling and synchronization problems of high-frequency feedback force servo. low-frequency dynamics solver servo and scene rendering servo, and realize highly stable and accurate force feedback in the physical simulation of product assembly and operation manipulation. This research proposes a physical simulation method of product assembly and operation manipulation.展开更多
The shear behavior of backfill-rock composites is crucial for mine safety and the management of surface subsidence.For exposing the shear failure mechanism of backfill-rock composites,we conducted shear tests on backf...The shear behavior of backfill-rock composites is crucial for mine safety and the management of surface subsidence.For exposing the shear failure mechanism of backfill-rock composites,we conducted shear tests on backfill-rock composites under three constant normal loads,compared with the unfilled rock.To investigate the macro-and meso-failure characteristics of the samples in the shear tests,the cracking behavior of samples was recorded by a high-speed camera and acoustic emission monitoring.In parallel with the experimental test,the numerical models of backfill-rock composites and unfilled rock were established using the discrete element method to analyze the continuous-discontinuous shearing process.Based on the damage mechanics and statistics,a novel shear constitutive model was proposed to describe mechanical behavior.The results show that backfill-rock composites had a special bimodal phenomenon of shearing load-deformation curve,i.e.the first shearing peak corresponded to rock break and the second shearing peak induced by the broken of aeolian sand-cement/fly ash paste backfill.Moreover,the shearing characteristic curves of the backfill-rock composites could be roughly divided into four stages,i.e.the shear failure of the specimens experienced:stage I:stress concentration;stage II:crack propagation;stage III:crack coalescence;stage IV:shearing friction.The numerical simulation shows that the existence of aeolian sand-cement/fly ash paste backfill inevitably altered the coalescence type and failure mode of the specimens and had a strengthening effect on the shear strength of backfillrock composites.Based on damage mechanics and statistics,a shear constitutive model was proposed to describe the shear fracture characteristics of specimens,especially the bimodal phenomenon.Finally,the micro-and meso-mechanisms of shear failure were discussed by combining the micro-test and numerical results.The research can advance the better understanding of the shear behavior of backfill-rock composites and contribute to the safety of mining engineering.展开更多
基金the National Natural Science Foundation of China(No.42076069)。
文摘The frontal edge of the Makran accretionary wedge is characterized by the development of multiple imbricate thrust faults trending E-W and relatively parallel.However,the mechanisms underlying their formation and the factors controlling their development remain subjects of debate.This paper,based on seismic profile analysis,employs physical simulation experiments to establish a'wedge'type subduction model.The study explores the influence of the initial wedge angle,horizontal sand layer thickness,and the presence or absence of a decollement layer on the structural styles of the thrust wedge.Experimental results indicate that as the initial wedge angle decreases from 11°to 8°,the lateral growth of the thrust wedge increases,whereas vertical growth diminishes.When the horizontal sand layer thickness is reduced from 4.5 cm to 3.0 cm,the spacing between the frontal thrusts decreases and the number of thrust faults increases.Both lateral and vertical growth are relatively reduced,resulting in a smaller thrust wedge.When a decollement layer is present,the structural style exhibits layered deformation.The decollement layer constrains the development of back thrusts and promotes the localized formation of frontal thrusts.In conclusion,the imbricate thrust faults at the frontal edge of the Makran accretionary wedge are primarily controlled by the characteristics of the wedge itself and the presence of the decollement layer.
基金Supported by the National Natural Science Foundation of China(42362026)Key R&D Project of Xinjiang Uygur Autonomous Region(2024B01015).
文摘In the ultra-deep strata of the Tarim Basin,the vertical growth process of strike-slip faults remains unclear,and the vertical distribution of fractured-cavity carbonate reservoirs is complex.This paper investigates the vertical growth process of strike-slip faults through field outcrop observations in the Keping area,interpretation of seismic data from the Fuman Oilfield,Tarim Basim,NW China,and structural physical simulation experiments.The results are obtained mainly in four aspects.First,field outcrops and ultra-deep seismic profiles indicate a three-layer structure within the strike-slip fault,consisting of fault core,fracture zone and primary rock.The fault core can be classified into three parts vertically:fracture-cavity unit,fault clay and breccia zone.The distribution of fracture-cavity units demonstrates a distinct pattern of vertical stratification,owing to the structural characteristics and growth process of the slip-strike fault.Second,the ultra-deep seismic profiles show multiple fracture-cavity units in the strike-slip fault zone.These units can be classified into four types:top fractured,middle connected,deep terminated,and intra-layer fractured.Third,structural physical simulation experiments and ultra-deep seismic data interpretation reveal that the strike-slip faults have evolved vertically in three stages:segmental rupture,vertical growth,and connection and extension.The particle image velocimetry detection demonstrates that the initial fracture of the fault zone occurred at the top or bottom and then evolved into cavities gradually along with the fault growth,accompanied by the emergence of new fractures in the middle part of the strata,which subsequently connected with the deep and shallow cavities to form a complete fault zone.Fourth,the ultra-deep carbonate strata primarily develop three types of fractured-cavity reservoirs:flower-shaped fracture,large and deep fault and staggered overlap.The first two types are larger in size with better reservoir conditions,suggesting a significant exploration potential.
基金Project (2011CB605505) supported by the National Basic Research Program of ChinaProject (2011QNZT041) supported by the freedom explore Program of Central South University,ChinaProject (84088) supported by the and Postdoctoral Foundation Supported Project of Central South University,China
文摘The hot forging of large-scale P/M TiAl alloy billet deformation was investigated based on a joint application of Deform-3D-based numerical simulation and physical simulation techniques.The temperature dependence on the thermal and mechanical properties of the billet was considered and the optimum hot working temperature of packed TiAl alloy was 1150-1200 °C.Based on the simulation,the material flow and thermo mechanical field variables,such as stress,strain,and temperature distribution were obtained and the relationships of load—displacement and load—time were figured out.To verify the validity of the simulation results,the experiments were also carried out in a forging plant,and a pancake with diameter of 150 mm was obtained exhibiting a regular shape.
文摘The contrast experiment of different stirring modes,which includes a new type of stirring-injection with the method of pulse and rotation,and the initial one-way stirring method,is done through physical simulation in the laboratory.The stirring methods of pulse and rotation are of two kinds.One is pulsed and rotary stirrer with positive and opposite directions.The other is pulsed and rotary stirrer with rotation-stop-rotation.The results show that the stirring mode of pulse and rotation has better effects than the one-way stirring method.The specific effects are that the mixing time of the melting bath is apparently shortened,the number of grains involved in the liquid surface is increased,and the residence time of air bubble in water is doubled.
基金Acknowledgements This work was financially supported by the National Key Research and Development Program （2016YFC0801402-4）, the National Natural Science Foundation of China （51374236, 51574280）, Chongqing Frontiers and Application- based Research Program （cstc2015jcyjBX0076）. Meanwhile, the author would like to thank the reviewers of this paper for their constructive comments and suggestions to improve the publication.
文摘Coal and gas outburst is one of the main gas hazards in coal mines. However, due to the risks of the coal and gas outburst, the field test is difficult to complete. Therefore, an effective approach to studying the mechanism and development of outburst is to conduct the similar physical simulation. However, the similarity criteria and similar materials in outburst are the key factors which restrict the development of physical simulation. To solve those problems, this paper has established similarity criteria base on mechanics model, solid-fluid coupling model and energy model, and presented high similar materials. Combining with three groups of similar number, and considering similar mechanical parameters and deformation and failure regularity, the similarity criteria of outburst is determined on the basis of the energy model. According to those criteria, we put forward a similar material consists of pulverized coal, cement, sand, activated carbon, and water. The similar material has high compressive strength and the accordant characteristics with the raw coal, include density, porosity, adsorption, desorption. The new research is promising for preventing and controlling gas hazards in the future.
文摘The kinetics of ε-Cu particles dissolution in the matrix during welding of a copper-precipitation strengthening steel was determined by a combination of GleebleTM physical simulation, TEM examination and hardness meas urement. The ε-Cu particles underwent a coarsening and part dissolution and then complete dissolution reaction as the peak temperature increased from 750 to 1 000℃, which resulted in the decrease in the number density of ε-Cu particles and hardness in the heat affected zone （HAZ）. The results can be used to understand the evolution of this transformation and a softening behavior of the HAZ during welding of this type of steel.
基金supported by the National Key R&D Program of China(Grant No.2018YFC1405900)the Major Projects of National Science and Technology(Grant Nos.2016ZX05011-002,2016ZX05027-002-005)+3 种基金the National Natural Science Foundation of China(Grant No.41806073)the Natural Science Foundation of Shandong Province(Grant No.ZR2017BD014)Shandong Provincial Key Laboratory of Depositional Mineralization and Sedimentary Minerals,Shandong University of Science and Technology(Grant No.DMSM2017042)the Fundamental Research Funds for the Central Universities(Grant No.201964016)
文摘To establish the relationship among reservoir characteristics and rock physical parameters,we construct the well-bore rock physical models firstly,considering the influence factors,such as mineral composition,shale content,porosity,fluid type and saturation.Then with analyzing the change rules of elastic parameters along with the above influence factors and the cross-plots among elastic parameters,the sensitive elastic parameters of tight sandstone reservoir are determined,and the rock physics template of sweet spot is constructed to guide pre-stack seismic inversion.The results show that velocity ratio and Poisson impedance are the most sensitive elastic parameters to indicate the lithologic and gas-bearing properties of sweet spot in tight sandstone reservoir.The high-quality sweet spot is characterized by the lower velocity ratio and Poisson impedance.Finally,the actual seismic data are selected to predict the sweet spots in tight sandstone gas reservoirs,so as to verify the validity of the rock physical simulation results.The significant consistency between the relative logging curves and inversion results in different wells implies that the utilization of well-bore rock physical simulation can guide the prediction of sweet spot in tight sandstone gas reservoirs.
文摘Mold-filling process of thin-walled castings under the condition of traveling magnetic field has been studied by physical simulation method using gallium melt and fast speed photography. Flow morphology and its formation mechanism were obtained and discussed for thin-walled casting. The influences of magnetic field density on the filling ability, filling velocity and mold filling time have been studied. The differences in filling capability between gravity casting and casting under the traveling magnetic field have been compared. The results indicate that the mold filling ability of the gallium melt increases greatly under the condition of traveling magnetic field; the filling time is shortened from 18 s under gravity field to 3 s under the traveling magnetic field and average flow rate of the melt increases from 1.6 to 8.68 cm3/s; the change law of the cross-section morphology of the gallium melt during the mold filling is that at first, the cross-section area does not change, then it decreases gradually. When the front of the melt reaches the end of the mold cavity, the front melt will backfill the mold; the wider the width of mold cavity, the better the mold filling ability. The mold filling ability of gallium melt in mold with upper magnetic conductor is better than that without upper magnetic conductor.
文摘Direct quenching and tempering （DQ-T） of hot rolled steel section has been widely used in steel mill for the sake of improvement of mechanical properties and energy saving. Temperature history and microstructural evolution during hot rolling plays a major role in the properties of direct quenched and tempered products. The mathematical and physical modeling of hot forming processes is becoming a very important tool for design and development of required products as well as predicting the microstructure and the properties of the components. These models were mostly used to predict austenite grain size （AGS）, dynamic, recta-dynamic and static recrystallization in the rods immediately after hot rolling and prior to DQ process. The hot compression tests were carried out on 42CrMo4 steel in the temperature range of 900-1 100 ℃ and the strain rate range of 0. 05-1 s^-1 in order to study the high tempera- ture softening behavior of the steel. For the exact prediction of flow stress, the effective stress-effective strain curves were obtained from experiments under various conditions. On the basis of experimental results, the dynamic recrystallization fraction （DRX）, AGS, hot deformation and activation energy behavior were investigated. It was found that the calculated results were in good agreement with the experimental flow stress and microstructure of the steel for different conditions of hot deformation.
基金Projects 50490270 and 50634050 supported by the National Natural Science Foundation of China2007CB209400 by the National Basic Research Program of China2006A039 by the Youth Scientific Research Foundation of China University of Mining & Technology
文摘The behavior of stress wave propagation in rock walls and the process of rock bursts were simulated by application tests of material similar to rock. Results show that 1) the attenuation characteristics of stress waves were related to the material proper-ties, stress waves attenuate more quickly in soft material and 2) when the explosion load was applied at the top of the roadway, the number and the length of the cracks increased with a decrease in the distance between the explosive point and roof of the roadway. When the distance was 280 mm, only some chips appeared near the source, when the distance was 210 mm, some small cracks started to appear near the road-rib and when the distance was reduced to 140 mm, larger cracks appeared at the road-rib. It can be concluded that, under a given stress the number of cracks is closely related to the intensity of stress waves. The cracks in the sur-rounding rock can be reduced by controlling the intensity of the stress waves and rock bursts can be avoided to some extent by pre-venting the formation of layered crack structures. A new experimental approach has been provided for studying rock bursts by using physical simulation.
基金Project 2002CB211705 supported by the National Basic Research Program of China
文摘In order to select highly productive and enriched areas of high rank coalbed methane reservoirs, based on hydrologic geology as one of the main factors controlling coalbed methane （CBM） reservoir formations, the effect of hydrodynamic forces controlling CBM reservoir formations was studied by a physical simulation experiment in which we used CBM reservoir simulation facilities. The hydrodynamic conditions of high coal rank reservoirs in the Qinshui basin were analyzed. Our experiment shows the following results： under strong hydrodynamic alternating action, 6C~ of coalbed methane reservoir changed from the start at -2.95% ~ -3.66%, and the lightening process occurred in phases; the CI-I4 volume reduced from 96.35% to 12.42%; the CO2 vo- lume decreased from 0.75% in sample 1 to 0.68% in sample 2, then rose to 1.13% in sample 3; the N2 volume changed from 2.9% in sample 1 to 86.45% in sample 3. On one hand, these changes show the complexity of CBM reservoir formation; on the other hand, they indicate that strong hydrodynamic actions have an unfavorable impact on CBM reservoir formation. It was found that the gas volume and hydrodynamic intensity were negatively correlated and low hydrodynamic flow conditions might result in highly productive and enriched areas of high rank CBM.
基金supported by National Natural Science Fundation of China (Grant No. 40772176)Key Program for Research Group of SKLGP (Grant No. SKLGP2009Z002)Research Fund for the Doctoral Program of Higher Education of China(Grant No. 20105122110008)
文摘According to the test results of the physical and mechanical properties of similar materials in various quality mixture, a type of material with obvious tendency of rockburst was selected to produce a large-size model to simulate rockburst phenomena in tunnels. The prototype model comes from a typical section of diversion tunnels in Jinping Hydropower Station in China. The simulation of excavating tunnels is carried out by opening a hole in the model after loading. The modeling results indicated that under the condition of normal stresses in the model boundaries the arch top, spandrel and side walls of the tunnel produced an obvious jump reaction of stress and strain and the acoustic emission counts of the surrounding rock also increased rapidly in a different time period after the "tunnel" excavation, showing the clear features of rockburst. The spalling, buckling and breaking occurred in the surrounding rock of model in conditions of over loading. It is concluded that the modeling tunnel segment in Jinping Hydropower Station is expected to form the tensile rockburst with the pattern of spalling, buckling and breaking.
基金financially supported by the National Natural Science Foundation of China(Grant Nos.50974049 and 51174068)the Heilongjiang Postdoctoral Science Foundation of China(Grant No.LBH-Z09009)
文摘A new physical simulation model was developed to simulate the casting process of the ductile iron heavy section spent-nuclear-fuel container.In this physical simulation model,a heating unit with DR24 Fe-Cr-Al heating wires was used to compensate the heat loss across the non-natural surfaces of the sample,and a precise and reliable casting temperature controlling/monitoring system was employed to ensure the thermal behavior of the simulated casting to be similar to the actual casting.Also,a mould system was designed,in which changeable mould materials can be used for both the outside and inside moulds for different applications.The casting test was carried out with the designed mould and the cooling curves of central and edge points at different isothermal planes of the casting were obtained.Results show that for most isothermal planes,the temperature control system can keep the temperature differences within 6 ℃ between the edge points and the corresponding center points,indicating that this new physical simulation model has high simulation accuracy,and the mould developed can be used for optimization of casting parameters of spent-nuclear-fuel container,such as composition of ductile iron,the pouring temperature,the selection of mould material and design of cooling system.In addition,to maintain the spheroidalization of the ductile iron,the force-chilling should be used for the current physical simulation to ensure the solidification of casting in less than 2 h.
基金the National Key Basic Research and Development Program of China(No.2015CB251600)the Preliminary National Key Basic Research and Development Program of China(No.2014CB260404)+1 种基金the National Key Natural Science Foundation of China(No.51034001,No.U13612030)the Shaanxi Innovation Team Program(No.2013KCT-16)
文摘High-steep slope stability and its optimal excavation design in Shuichang open pit iron mine were analyzed based on a large 3D physical simulation technique. An optimal excavation scheme with a relatively steeper slope angle was successfully implemented at the northwest wall between Nos. 4 and 5 exploration lines of Shuichang Iron Mine, taking into account the 3D scale effect. The phys-ico-mechanical properties of rock materials were obtained by laboratory tests conducted on sample cores from exploration drilling directly from the iron mine. A porous rock-like composite material was formed for the model, and the mechanical parameters of the material were assessed experimentally;specifically, the effect of water on the sample was quantitatively determined. We adopted an experimental setup using stiff modular applied static loading to carry out a visual excavation of the slope at a random depth. The setup was equipped with acous-tic emission （AE） sensors, and the experiments were monitored by crack optical acquirement, ground penetrating radar, and close-field pho-togrammetry to investigate the mechanisms of rock-mass destabilization in the high-steep slope. For the complex study area, the model re-sults indicated a clear correlation between the model＇s destabilization resulting from slope excavation and the collected monitoring informa-tion. During the model simulation, the overall angle of the slope increased by 1-6 degrees in different sections. Dramatically, the modeled excavation scheme saved over 80 million tons of rock from extraction, generating enormous economic and ecological benefits.
基金supported by the National Natural Science Foundation of China(U1508217,U1702253 and 51774078)the Fundamental Research Funds for the Central Universities(N172506009 and N170908001).
文摘In order to increase the contact area and promote the mass transfer process of gas and liquid,the process of the bubble refine-ment in a metallurgical reactor with mechanical agitation was studied by physical simulation.Based on the capillary number,a prediction equation for the bubble refinement was established.The effects of the gas flow rate,the stirring speed and thestirring depth on the bubble refinement in the reactor were discussed in detail.The distribution of the bubble diameter in thereactor was obtained under different conditions.The results show that when the stirring speed reaches 300 r/min,the bubblediamcter mainly distributes in the range of 1-2 mm.A higher gas flow rate may increase the number of bubbles in the meltand promote the bubble refinement process.The mechanism of bubble refinement under mechanical agitation was analyzed.and the results indicated that the stirring speed.,the blade area and the blade inclination are the main influencing factors.
基金supported by the National Natural Science Foundation of China (Grant Nos. 51079023 and 50921001)the Program for New Century Excellent Talents in University (Grant No. NCET-05-0282)
文摘Real waves are multidirectional waves. In the present study, the calculation method for the wave maker driving signals for generating multidirectional wave groups in physical wave basin is proposed. Its validity is first confirmed by a numerical model for which the incident boundary condition is determined by use of the proposed method. Then, the physical simulation of multidirectional wave groups is performed in laboratory wave basin. The experimental results show that multidirectional waves with expected wave groupiness, which includes not only its group height but also its group length, can be satisfactorily zenerated at the soecified oosition in the tphvsical wave basin.
基金Supported by the PetroChina Major Scientific and Technological Research Project (2021DJ1102)PetroChina Science and Technology Major Project (2022kt1001)。
文摘In order to understand the mechanism of air flooding shale oil, an online physical simulation method for enhanced shale oil recovery by air injection was established by integrating CT scanning and nuclear magnetic resonance(NMR). The development effect of shale oil by air flooding under different depletion pressures, the micro-production characteristics of pore throats with different sizes and the mechanism of shale oil recovery by air flooding were analyzed. The effects of air oxygen content, permeability, gas injection pressure, and fractures on the air flooding effect in shale and crude oil production in pores with different sizes were analyzed. The recovery of shale oil can be greatly improved by injecting air into the depleted shale reservoir, but the oil displacement efficiency and the production degree of different levels of pore throats vary with the injection timing. The higher the air oxygen content and the stronger the low-temperature oxidation, the higher the production degree of pores with different sizes and the higher the shale oil recovery. The higher the permeability and the better the pore throat connectivity, the stronger the fluid flow capacity and the higher the shale oil recovery. As the injection pressure increases, the lower limit of the production degree of pore throats decreases, but gas channeling may occur to cause a premature breakthrough;as a result, the recovery increases and then decreases. Fractures can effectively increase the contact area between gas and crude oil, and increase the air sweep coefficient and matrix oil drainage area by supplying oil to fractures through the matrix, which means that a proper fracturing before air injection can help to improve the oil displacement effect under a reasonable production pressure difference.
基金Project supported by the National Basic Research Program (973) of China (No. 2002CB312101) and the National Natural Science Foundation of China (No. 60475013)
文摘Realistic modeling and rendering of dynamic tornado scene is recognized as a challenging task for researchers of computer graphics. In this paper a new physically based method for simulating and animating tornado scene is presented. We first propose a Two-Fluid model based on the physical theory of tornado, then we simulate the flow of tornado and its interaction with surrounding objects such as debris, etc. Taking the scattering and absorption of light by the participating media into account, the illumination effects of the tornado scene can be generated realistically. With the support of graphics hardware, various kinds of dynamic tornado scenes can be rendered at interactive rates.
基金Supported by National Natural Science Foundation of China(51475418)National Basic Research 973 Program of China(2011CB706503)Science Fund for Creative Research Groups of National Natural Science Foundation of China(51221004)
文摘Most existing force feedback methods are still difficult to meet the requirements of real-time force calculation in virtual assembly and operation with complex objects. In addition, there is often an assumption that the controlled objects are completely flee and the target object is only completely fixed or flee, thus, the dynamics of the kinematic chain where the controlled objects are located are neglected during the physical simulation of the product manipulation with force feedback interaction. This paper proposes a physical simulation method of product assembly and operation manipulation based on statistically learned contact force prediction model and the coupling of force feedback and dynamics. In the proposed method, based on hidden Markov model （HMM） and local weighting learning （LWL）, contact force prediction model is constructed, which can estimate the contact force in real time during interaction. Based on computational load balance model, the computing resources are dynamically assigned and the dynamics integral step is optimized. In addition, smoothing process is performed to the force feedback on the synchronization points. Consequently, we can solve the coupling and synchronization problems of high-frequency feedback force servo. low-frequency dynamics solver servo and scene rendering servo, and realize highly stable and accurate force feedback in the physical simulation of product assembly and operation manipulation. This research proposes a physical simulation method of product assembly and operation manipulation.
文摘The shear behavior of backfill-rock composites is crucial for mine safety and the management of surface subsidence.For exposing the shear failure mechanism of backfill-rock composites,we conducted shear tests on backfill-rock composites under three constant normal loads,compared with the unfilled rock.To investigate the macro-and meso-failure characteristics of the samples in the shear tests,the cracking behavior of samples was recorded by a high-speed camera and acoustic emission monitoring.In parallel with the experimental test,the numerical models of backfill-rock composites and unfilled rock were established using the discrete element method to analyze the continuous-discontinuous shearing process.Based on the damage mechanics and statistics,a novel shear constitutive model was proposed to describe mechanical behavior.The results show that backfill-rock composites had a special bimodal phenomenon of shearing load-deformation curve,i.e.the first shearing peak corresponded to rock break and the second shearing peak induced by the broken of aeolian sand-cement/fly ash paste backfill.Moreover,the shearing characteristic curves of the backfill-rock composites could be roughly divided into four stages,i.e.the shear failure of the specimens experienced:stage I:stress concentration;stage II:crack propagation;stage III:crack coalescence;stage IV:shearing friction.The numerical simulation shows that the existence of aeolian sand-cement/fly ash paste backfill inevitably altered the coalescence type and failure mode of the specimens and had a strengthening effect on the shear strength of backfillrock composites.Based on damage mechanics and statistics,a shear constitutive model was proposed to describe the shear fracture characteristics of specimens,especially the bimodal phenomenon.Finally,the micro-and meso-mechanisms of shear failure were discussed by combining the micro-test and numerical results.The research can advance the better understanding of the shear behavior of backfill-rock composites and contribute to the safety of mining engineering.
