The outermost coating with single phase Ni2Al3 was obtained on copper surface by electrodepositing nickel followed by slurry pack aluminizing at 800 °C for 12 h. The oxidation resistance and microstructure of the...The outermost coating with single phase Ni2Al3 was obtained on copper surface by electrodepositing nickel followed by slurry pack aluminizing at 800 °C for 12 h. The oxidation resistance and microstructure of the coating oxidized in ambient air at 1000 °C for 25-250 h were investigated using SEM, X-ray diffraction and optical microscope methods. The results show that the copper with single phase Ni2Al3 coating possesses the best high temperature oxidation resistance, and the mass gain of the coating is 1/15 that of pure copper and 1/2 that of nickel coating, respectively. The specimen surface after being oxidized for 25 h still comprises Ni2Al3 phase. However, when the time of oxidizing treatment increases to 50 h, the Ni Al phase is formed. It is also found that the Ni2Al3 phase completely turns into Ni Al phase after oxidizing treatment for 100 h and above. The Ni Al coating shows excellent high temperature oxidation resistance when oxidation time is 250 h.展开更多
A Ti(Al,Si)3 diffusion coating was prepared on γ-TiAl alloy by cold sprayed Al?20Si alloy coating, followed by a heat-treatment. The isothermal and cyclic oxidation tests were conducted at 900 °C for 1000 h and ...A Ti(Al,Si)3 diffusion coating was prepared on γ-TiAl alloy by cold sprayed Al?20Si alloy coating, followed by a heat-treatment. The isothermal and cyclic oxidation tests were conducted at 900 °C for 1000 h and 120 cycles to check the oxidation resistance of the coating. The microstructure and phase transformation of the coating before and after the oxidation were studied by SEM, XRD and EPMA. The results indicate that the diffusion coating shows good oxidation resistance. The mass gain of the diffusion coating is only a quarter of that of bare alloy. After oxidation, the diffusion coating is degraded into three layers: an inner TiAl2 layer, a two-phase intermediate layer composed of a Ti(Al,Si)3 matrix and Si-rich precipitates, and a porous layer because of the inter-diffusion between the coating and substrate.展开更多
The isothermal oxidation behavior of NiAl-31Cr-2.9Mo-0.1Hf-0.05Ho directional eutectic alloy was investigated with the help of scanning electron microscopy and X-ray diffraction.The results revealed that a continuous ...The isothermal oxidation behavior of NiAl-31Cr-2.9Mo-0.1Hf-0.05Ho directional eutectic alloy was investigated with the help of scanning electron microscopy and X-ray diffraction.The results revealed that a continuous Al2O3 scale was formed and owned excellent oxidation resistance in the temperature range of 900-1100°C.When the temperature was up to 1150°C,the continuous Al2O3 oxide film ruptured.Trace rare earth element Ho distributed uniformly in the alloy and relatively high level of Al in Cr（Mo）phase are beneficial to the formation of continuous and compact Al2O3 scale.During the oxidation,a phase transformation fromθ-Al2O3 toα-Al2O3 existed on the surface of oxidation film.It resulted in the abnormal oxidation mass gain happening when the alloy was oxidized at 1000°C or 1050°C.展开更多
Refractory high entropy alloys have superior mechanical properties at high temperatures, and the oxidation behavior of these alloys is very important. The present work investigated the high temperature oxidation behav...Refractory high entropy alloys have superior mechanical properties at high temperatures, and the oxidation behavior of these alloys is very important. The present work investigated the high temperature oxidation behavior of three alloys with compositions of TiNbTa0.5Zr, TiNbTa0.5ZrAl and TiNbTa0.5ZrAlMo0.5, and the effects of alloying elements were discussed. Results indicated that the oxidation rates of the TiNbTa0.5Zr and TiNbTa0.5ZrAl alloys are controlled by diffusion, and obey the exponential rule. However, the oxidation rate of the TiNbTa0.5ZrAlMo0.5 alloy is controlled by interface reaction, and obeys the linear rule. The addition of Al leads to a better oxidation resistance by forming a protective oxide scale. However, the protection of Al-rich scale is weakened by the addition of Mo. Extensive pores and cracks occur in the oxide scale of the TiNbTa0.5ZrAlMo0.5 alloy, resulting in a significant decrease in oxidation resistance.展开更多
Two experimental single crystal superalloys Y-free alloy and Y-containing alloy were cast in the directionally solidified furnace, while other alloying element contents were basically kept unchanged. The isothermal ox...Two experimental single crystal superalloys Y-free alloy and Y-containing alloy were cast in the directionally solidified furnace, while other alloying element contents were basically kept unchanged. The isothermal oxidation behavior of two single crystal superalloy was studied at 1100 ℃ in ambient atmosphere. Morphology of oxides was examined by scanning electron microscopy （SEM） and their compostion was analyzed by X-ray diffraction （XRD） and energy dispersive spectroscopy （EDS）. The effect of yt- trium on the high temperature oxidation resistance of the single crystal superalloy was investigated. The results showed that the oxi- dation resistance of Ni-base single crystal superalloy was substantially improved by adding a little amount of rare earth yttrium. Yt- trium could promote the oxide of A1 formation and decreased the proportion of NiO. Yttrium increased the coherence between the oxide scale and the alloy substrate to decrease the spallation of oxide scale. Yttrium reduced the oxide grain size and the thickness of oxide layer.展开更多
Catalytic oxidation of formaldehyde (HCHO) is the most efficient way to purify indoor air of HCHO pollutant. This work investigated rare earth La‐doped Pt/TiO2 for low concentration HCHO oxidation at room temperature...Catalytic oxidation of formaldehyde (HCHO) is the most efficient way to purify indoor air of HCHO pollutant. This work investigated rare earth La‐doped Pt/TiO2 for low concentration HCHO oxidation at room temperature. La‐doped Pt/TiO2 had a dramatically promoted catalytic performance for HCHO oxidation. The reasons for the La promotion effect were investigated by N2 adsorption, X‐raydiffraction, CO chemisorption, X‐ray photoelectron spectroscopy, transmission electron microscopy(TEM) and high‐angle annular dark field scanning TEM. The Pt nanoparticle size was reduced to 1.7nm from 2.2 nm after modification by La, which led to higher Pt dispersion, more exposed activesites and enhanced metal‐support interaction. Thus a superior activity for indoor low concentrationHCHO oxidation was obtained. Moreover, the La‐doped TiO2 can be wash‐coated on a cordieritemonolith so that very low amounts of Pt (0.01 wt%) can be used. The catalyst was evaluated in asimulated indoor HCHO elimination environment and displayed high purifying efficiency and stability.It can be potentially used as a commercial catalyst for indoor HCHO elimination.展开更多
The effect of rare earth element yttrium on the high temperature oxidation resistance of a directionally solidified Ni-base superalloy was studied with scanning electron microscopy(SEM), energy dispersive spectrum(EDS...The effect of rare earth element yttrium on the high temperature oxidation resistance of a directionally solidified Ni-base superalloy was studied with scanning electron microscopy(SEM), energy dispersive spectrum(EDS)and X-ray diffraction(XRD)techniques. The results show that the oxidation resistance of the alloy is substantially improved by adding proper amount of yttrium.展开更多
High temperature oxidation behaviors of FGH96 P/M superaUoy have been studied in air at temperatures ranging from 600 to 1000℃. By means of isothermal oxidation testing, X-ray diffraction, SEM （scanning electron mic...High temperature oxidation behaviors of FGH96 P/M superaUoy have been studied in air at temperatures ranging from 600 to 1000℃. By means of isothermal oxidation testing, X-ray diffraction, SEM （scanning electron microscopy）, and EDS （energy dispersive X-ray spectroscopy） analyses, the oxidation kinetics as well as the composition and morphology of scales were investigated. Thermodynamic calculations were used to explain the oxidation mechanism. The results showed that as the oxidation temperature increased, the oxidation rate, the scale thickness, and scale spallation increased. FGH96 P/M superalloy exhibits good oxidation resistance at temperature below 800℃. The oxidation kinetics follows an approximately parabolic rate law, and the oxide layer was mainly composed of Cr2O3 TiO2 and a little amount of NiCr2O4. The oxidation is controlled by the transmission of chromium. titanium, and oxygen through the oxide scale.展开更多
The present study investigated the effect of as-built and post heat-treated microstructures of IN738LC alloy fabricated via selective laser melting process on high temperature oxidation behavior.The as-built microstru...The present study investigated the effect of as-built and post heat-treated microstructures of IN738LC alloy fabricated via selective laser melting process on high temperature oxidation behavior.The as-built microstructure showed fine cell and columnar structure due to high cooling rate.Ti element segregation was observed in inter-cell/inter-columnar area.After post heat-treatment,the initially-observed cell structure disappeared,instead bimodal Ni_3(Al,Ti)particles formed.High temperature(1273 K and 1373 K)oxidation test results showed parabolic oxidation curves regardless of temperature and initial microstructure.The as-built IN738LC fabricated via the selective laser melting process displayed oxidation resistance similar to or slightly better than that of IN738LC fabricated via wrought or cast process.Heat-treated SLM IN738LC,although had similar oxidation weight-gain values to those of the SLM asbuilt material at 1273K,showed relatively better oxidation resistance at 1373 K.Bimodal Ni_3(Al,Ti)precipitate formed in the post heat treatment changed the local chemical composition,thereby led to changes in alumina former/chromia former location and fraction on the alloy surface.It was concluded that in heat-treated IN738LC increased alumina former fraction was found,and this resulted in excellent oxidation resistance and relatively low weight-gain.展开更多
Inconel 600 alloy is widely utilized for high temperature environment application due to the corresponding good oxidation and corrosion resistance properties.In order to estimate the high temperature oxidation resista...Inconel 600 alloy is widely utilized for high temperature environment application due to the corresponding good oxidation and corrosion resistance properties.In order to estimate the high temperature oxidation resistance of Inconel 600 alloy at various temperatures,the oxidation weight gain of all specimens was measured and fitted for the curve at the temperatures of 700,800 and 900 ℃ for exposure time of 100 h.The surface morphology and the component of the oxide film were analyzed by scanning electron microscopy(SEM),energy-dispersive spectroscopy(EDS) and X-ray diffraction(XRD).The results indicate that the high temperature oxidation resistance of Inconel 600 alloy is excellent blew 800℃ due to the oxidation kinetic curves at different temperatures corresponding to the parabola dynamic rules.This means that the oxidation film protects the substrate well.The dense oxide layer formation containing Cr_(2)O_(3) and NiCr_(2)O_(4) at 700 and 800 ℃ and MnCr_(2)O_(4) at 900 ℃,respectively,is the main reason for the good oxidation resistance.In contrast,the oxide layer peels off easily under applied force as the temperature increases beyond 800℃, on account of the complicated compositions of the oxide film and the binding force between the oxide layer and the substrate weakening.Corresponding oxidation mechanism is expected to be understood and the oxidation resistance of Inconel 600 alloy is improved through binding force enhancement.展开更多
The effect of Si on the high temperature oxidation behavior of the 30Cr13 martensitic stainless steels was investigated. The underlying mechanism was further discussed by oxidation kinetics curves, scanning electron m...The effect of Si on the high temperature oxidation behavior of the 30Cr13 martensitic stainless steels was investigated. The underlying mechanism was further discussed by oxidation kinetics curves, scanning electron microscopy （SEM） and X-ray diffraction （XRD） analysis. It was ob- served that the addition of Si can significantly reduce the mass gain per unit area and the oxidation rate of the experimental steels. With the increase of Si content, the film surface composed of the wheat-like oxides turned into the small granular oxides after oxidation for 120 h. The SiO_2 film formed on the metal substrate inhibited the outward diffusion of the metal cation and the inward diffusion of the oxygen anion; thus, the high temperature oxidation resistance was enhanced.展开更多
Fourier transform infrared spectroscopy(FTIR) and constant heating rate experiments were performed to study the low temperature oxidation of coal treated by an ionic liquid,1-allyl-3-methylimidazolium chloride.The ine...Fourier transform infrared spectroscopy(FTIR) and constant heating rate experiments were performed to study the low temperature oxidation of coal treated by an ionic liquid,1-allyl-3-methylimidazolium chloride.The inerting effect of the ionic liquid toward the low temperature oxidation process is discussed.The results show that:(1) The hydroxyl content associated with hydrogen bonds,the aliphatic methyl content,the methylene group content,and the ether oxygen bond content are reduced in the treated coal.At the same time the content of aromatic C@C bonds is constant but these chemical bonds weaken and some substituted aromatic hydrocarbon content increases while other types decrease.This demonstrates that(AMIm)Cl dissolves and destroys the coal surface microstructure;(2) The oxygen consumption of the treated coal is less than what is seen in raw coal.The CO,CO 2,C 2 H 4,and C 2 H 6 content from the treated coal is reduced compared to the untreated coal;(3) The apparent activation energy for the oxidizing reaction is different in the treated and raw coals.Micro-structural changes and macroscopic gas production allow us to conclude that(AMIm)Cl can effectively inhibit low temperature oxidation of coal.展开更多
In high temperature oxidation environment, the oxidation reaction will induce variations in material parameters, such as Young's modulus, thermal expansion coefficient (CTE), coefficient of oxygen diffusion (COD),...In high temperature oxidation environment, the oxidation reaction will induce variations in material parameters, such as Young's modulus, thermal expansion coefficient (CTE), coefficient of oxygen diffusion (COD), etc. The oxidation -induced material parameter variations should be considered in high temperature mechanical analysis. In this paper, high temperature oxidation behavior of an oxide film/metal substrate system was investigated through a modified phase field approach. The oxidative stress and oxidation weight gain induced by high temperature oxidation were studied. Effects of Young's modulus, COD and CTE on oxidative stress in the oxide film were studied particularly. The simulation results showed that a better agreement with the experimental results could be obtained when considering the oxidation -induced material parameter variations in the high temperature mechanical analysis of oxide film/metal substrate system. The simulation results demonstrated that oxidative stress and oxidation weight gain were more sensitive to the variation of Young's modulus than to the variations of COD and CTE.展开更多
The effect of a sputtered Ti-48AI-8Cr-2Ag (at. pct) coating on the oxidation resistance of the cast Ti-46.5AI-5Nb (at. pct) alloy was investigated in air at 1000-1100℃. Hot corrosion in molten 75 wt pct Na2SO4+25 wt ...The effect of a sputtered Ti-48AI-8Cr-2Ag (at. pct) coating on the oxidation resistance of the cast Ti-46.5AI-5Nb (at. pct) alloy was investigated in air at 1000-1100℃. Hot corrosion in molten 75 wt pct Na2SO4+25 wt pct K2SO4 was investigated at 900℃. The scale on the cast TiAINb tends to spall in air, while the scale on coating is very adherent. The sputtered Ti-48AI-8Cr-2Ag coating remarkably improved high temperature oxidation resistance of the cast Ti-46.5AI-5Nb alloy because of the formation of an adherent Al2O3 scale. Due to the inward diffusion of Cr, Kirkendall voids were found at the coating/substrate interface. TiAICrAg coating provided excellent hot corrosion resistance for TiAINb alloy in molten 75 wt pct Na2SO4+25 wt pct K2S04 at 900℃ due to the formation of a continuous Al_2O_3 scale.展开更多
Oxidation rates and scale/steel interface configuration of 9Ni steels were investigated at 1000--1 250 ℃ in air. The results revealed that Cu addition caused high temperature oxidation resistance to deteriorate. High...Oxidation rates and scale/steel interface configuration of 9Ni steels were investigated at 1000--1 250 ℃ in air. The results revealed that Cu addition caused high temperature oxidation resistance to deteriorate. High tempera ture oxidation rates increased and scale/steel interface configuration became complicated due to Cu addition. Scale/ steel interface appeared to be network above certain temperature. Temperature required to form network scale/steel interface dropped more than 100 ℃ for 1.5% Cu-containing steel. （Fe,Ni,Cu）x Oy in inner oxidation layer dissocia ted to Fe-Ni-Cu phase and released active oxygen which can react with base steel easily. So the inner oxidation layer became the second source of oxidizing agent besides atmosphere. Internal stress at austenite grain boundary caused local oxide to fragment. So the scale/steel interface appeared to be network. Liquid Si-rich phase formed at sufficient ly high temperature. Penetration of the liquid Si-rich phase along austenite grain enhanced austenite grain oxidizing.展开更多
By analyzing previous studies on activation energy of coal oxidation at low temperatures, a theoretical calculation model of apparent activation energy is established. Yield of CO is measured by using the characterist...By analyzing previous studies on activation energy of coal oxidation at low temperatures, a theoretical calculation model of apparent activation energy is established. Yield of CO is measured by using the characteristic detector of coal oxidation at 30-90 ℃. The impact of parameters, such as airflow and particle size, on activation energies is analyzed. Finally, agreement was obtained between activation energies and the dynamic oxygen absorbed in order to test the accuracy of the model. The results show that： 1） a positive exponential relation between concentration of CO and temperature in the process of the experiment is obtained： increases are almost identical and the initial CO is low; 2） the apparent activation energies increase gradually with the sizes of particle at the same airflow, but the gradients increase at a decreasing rate; 3） the apparent activation energies increase linearly with airflow. For the five coal particles, the differences among the energies are relatively high when the airflow was low, but the differences were low when the airflow was high; 4） the optimum sizes of particle, 0.125-0.25 ram, and the optimum volume of airflow, 100 mL/min, are determined from the model; 5） the apparent activation energies decrease with an increase in oxygen absorbed. A negative exponential relation between the two is obtained,展开更多
Laser powder bed fusion(L-PBF)has been employed to additively manufacture WE43 magnesium(Mg)alloy biodegradable implants,but WE43 L-PBF samples exhibit excessively rapid corrosion.In this work,dense WE43 L-PBF samples...Laser powder bed fusion(L-PBF)has been employed to additively manufacture WE43 magnesium(Mg)alloy biodegradable implants,but WE43 L-PBF samples exhibit excessively rapid corrosion.In this work,dense WE43 L-PBF samples were built with the relativity density reaching 99.9%.High temperature oxidation was performed on the L-PBF samples in circulating air via various heating temperatures and holding durations.The oxidation and diffusion at the elevated temperature generated a gradient structure composed of an oxide layer at the surface,a transition layer in the middle and the matrix.The oxide layer consisted of rare earth(RE)oxides,and became dense and thick with increasing the holding duration.The matrix was composed ofα-Mg,RE oxides and Mg_(24)RE_(5) precipitates.The precipitates almost disappeared in the transition layer.Enhanced passivation effect was observed in the samples treated by a suitable high temperature oxidation.The original L-PBF samples lost 40%weight after 3-day immersion in Hank’s solution,and broke into fragments after 7-day immersion.The casted and solution treated samples lost roughly half of the weight after 28-day immersion.The high temperature oxidation samples,which were heated at 525℃ for 8 h,kept the structural integrity,and lost only 6.88%weight after 28-day immersion.The substantially improved corrosion resistance was contributed to the gradient structure at the surface.On one hand,the outmost dense layer of RE oxides isolated the corrosive medium;on the other hand,the transition layer considerably inhibited the corrosion owing to the lack of precipitates.Overall,high temperature oxidation provides an efficient,economic and safe approach to inhibit the corrosion of WE43 L-PBF samples,and has promising prospects for future clinical applications.展开更多
Self-lubricating composites(SLCs)are widely used in the fields of aerospace and marine,but the conventional NiCr matrix SLCs with sulfide as solid lubricant often suffer from low wear resistance at high temperatures.I...Self-lubricating composites(SLCs)are widely used in the fields of aerospace and marine,but the conventional NiCr matrix SLCs with sulfide as solid lubricant often suffer from low wear resistance at high temperatures.In view of its high affinity with oxygen and also the high oxidation rate,appropriate amount of nano Ti was added to NiCr-WS_(2)composites prepared by spark plasma sintering(SPS)to adjust the oxidation behavior and surface texture.When exposed to high temperature,Ti was preferentially oxidized in comparison to Ni and Cr,resulting in abundant TiO_(2)protrusions and microdimples on the surface,i.e.in situ surface texturing.Besides,TiO_(2)was of high chemical activity and readily to react with other oxide debris during high temperature sliding process to form compounds of NiTiO_(3)and CrTi_(2)O_(5).The high chemical activity of oxide debris that was conducive to sintering,combining with the special surface texture that stores as many wear debris as possible,promoted the rapid formation of a protective glaze layer on the sliding surface.The NiCr-WS_(2)-Ti composite exhibited low friction coefficient but high wear resistance at elevated temperatures.Especially at 800℃,it presented a wear rate of as low as(2.1±0.3)×10^(-5)mm^3N-1m^(-1),accounting for only 2.7%of that of NiCr-WS_(2)composite.展开更多
The interfacial behavior of sulfur and yttrium in the yttrium modified Ni 3Al based alloy IC6 during oxidation at 1100 ℃ was analyzed by X ray line scan of electron probe microstructural analysis(EPMA). The resul...The interfacial behavior of sulfur and yttrium in the yttrium modified Ni 3Al based alloy IC6 during oxidation at 1100 ℃ was analyzed by X ray line scan of electron probe microstructural analysis(EPMA). The results show that the migration and segregation of sulfur to the interface between oxide scale and the substrate at high temperature is retarded owing to the presence of yttrium. This is attributed to the desulfurization by yttrium in the melt and the trapping of sulfur by yttrium rich phases during oxidation, which leads to improving the coherence between oxide scale and substrate. Another reason of increasing the high temperature oxidation resistance of alloy IC6 by the addition of yttrium is that yttrium migrates to the grain boundaries of oxides during oxidation and hence improve their strength. This results in the transformation of the oxide scale spallation cracks from intergranular cracks for alloy without yttrium to transgranular ones for yttrium modified alloy.展开更多
Laser powder bed fusion(L-PBF)has been used to fabricate biodegradable Mg implants of WE43 alloy,but the degradation is too fast compared with the term bone reconstruction.Previous studies show that high temperature o...Laser powder bed fusion(L-PBF)has been used to fabricate biodegradable Mg implants of WE43 alloy,but the degradation is too fast compared with the term bone reconstruction.Previous studies show that high temperature oxidation(HTO)can successfully inhibit the degradation of WE43 alloy.In this work,the influence of HTO on L-PBF samples of WE43 alloy was investigated regarding tensile,compressive,and abrasive resistance,as well as in vitro cytotoxicity,cell proliferation,hemolysis,and osteogenesis.Compared with the as-built L-PBF samples,HTO increased grain size and grain texture,stabilized and coarsened precipitates,and caused discontinuous static recrystallization in the matrix.The oxide layer at the surface of the HTO samples improved surface roughness,hydrophilia,hardness,and abrasive resis-tance.The tensile strength decreased slightly from 292 to 265 MPa,while the elongation substantially increased from 10.97%to 16.58%after HTO.The in vitro cell viability,cell proliferation,hemolysis,and osteogenic effect were considerably enhanced due to the improvement of surface quality and the initial inhibition of excessive Mg^(2+)releasement.Overall,HTO is of great benefit to the surface performance,ductility,and biocompatibility of WE43 alloy fabricated by L-PBF for biodegradable applications.展开更多
基金Projects(CKJB201205,QKJB201202,YJK201307)supported by the Nanjing Institute of Technology,China
文摘The outermost coating with single phase Ni2Al3 was obtained on copper surface by electrodepositing nickel followed by slurry pack aluminizing at 800 °C for 12 h. The oxidation resistance and microstructure of the coating oxidized in ambient air at 1000 °C for 25-250 h were investigated using SEM, X-ray diffraction and optical microscope methods. The results show that the copper with single phase Ni2Al3 coating possesses the best high temperature oxidation resistance, and the mass gain of the coating is 1/15 that of pure copper and 1/2 that of nickel coating, respectively. The specimen surface after being oxidized for 25 h still comprises Ni2Al3 phase. However, when the time of oxidizing treatment increases to 50 h, the Ni Al phase is formed. It is also found that the Ni2Al3 phase completely turns into Ni Al phase after oxidizing treatment for 100 h and above. The Ni Al coating shows excellent high temperature oxidation resistance when oxidation time is 250 h.
基金Project(50971127)supported by the National Natural Science Foundation of China
文摘A Ti(Al,Si)3 diffusion coating was prepared on γ-TiAl alloy by cold sprayed Al?20Si alloy coating, followed by a heat-treatment. The isothermal and cyclic oxidation tests were conducted at 900 °C for 1000 h and 120 cycles to check the oxidation resistance of the coating. The microstructure and phase transformation of the coating before and after the oxidation were studied by SEM, XRD and EPMA. The results indicate that the diffusion coating shows good oxidation resistance. The mass gain of the diffusion coating is only a quarter of that of bare alloy. After oxidation, the diffusion coating is degraded into three layers: an inner TiAl2 layer, a two-phase intermediate layer composed of a Ti(Al,Si)3 matrix and Si-rich precipitates, and a porous layer because of the inter-diffusion between the coating and substrate.
基金Project(51101055)supported by the National Natural Science Foundation of China
文摘The isothermal oxidation behavior of NiAl-31Cr-2.9Mo-0.1Hf-0.05Ho directional eutectic alloy was investigated with the help of scanning electron microscopy and X-ray diffraction.The results revealed that a continuous Al2O3 scale was formed and owned excellent oxidation resistance in the temperature range of 900-1100°C.When the temperature was up to 1150°C,the continuous Al2O3 oxide film ruptured.Trace rare earth element Ho distributed uniformly in the alloy and relatively high level of Al in Cr（Mo）phase are beneficial to the formation of continuous and compact Al2O3 scale.During the oxidation,a phase transformation fromθ-Al2O3 toα-Al2O3 existed on the surface of oxidation film.It resulted in the abnormal oxidation mass gain happening when the alloy was oxidized at 1000°C or 1050°C.
基金Project(51671217)supported by the National Natural Science Foundation of ChinaProject(CX2017B047)supported by the Program of Innovation for Postgraduate of Hunan Province,China
文摘Refractory high entropy alloys have superior mechanical properties at high temperatures, and the oxidation behavior of these alloys is very important. The present work investigated the high temperature oxidation behavior of three alloys with compositions of TiNbTa0.5Zr, TiNbTa0.5ZrAl and TiNbTa0.5ZrAlMo0.5, and the effects of alloying elements were discussed. Results indicated that the oxidation rates of the TiNbTa0.5Zr and TiNbTa0.5ZrAl alloys are controlled by diffusion, and obey the exponential rule. However, the oxidation rate of the TiNbTa0.5ZrAlMo0.5 alloy is controlled by interface reaction, and obeys the linear rule. The addition of Al leads to a better oxidation resistance by forming a protective oxide scale. However, the protection of Al-rich scale is weakened by the addition of Mo. Extensive pores and cracks occur in the oxide scale of the TiNbTa0.5ZrAlMo0.5 alloy, resulting in a significant decrease in oxidation resistance.
文摘Two experimental single crystal superalloys Y-free alloy and Y-containing alloy were cast in the directionally solidified furnace, while other alloying element contents were basically kept unchanged. The isothermal oxidation behavior of two single crystal superalloy was studied at 1100 ℃ in ambient atmosphere. Morphology of oxides was examined by scanning electron microscopy （SEM） and their compostion was analyzed by X-ray diffraction （XRD） and energy dispersive spectroscopy （EDS）. The effect of yt- trium on the high temperature oxidation resistance of the single crystal superalloy was investigated. The results showed that the oxi- dation resistance of Ni-base single crystal superalloy was substantially improved by adding a little amount of rare earth yttrium. Yt- trium could promote the oxide of A1 formation and decreased the proportion of NiO. Yttrium increased the coherence between the oxide scale and the alloy substrate to decrease the spallation of oxide scale. Yttrium reduced the oxide grain size and the thickness of oxide layer.
基金supported by the National Key Research and Development Program (2016YFC0205900)the National Natural Science Foundation of China (21503106, 21567016)+1 种基金the Education Department of Jiangxi Province (KJLD14005)the Natural Science Foundation of Jiangxi Province (20142BAB213013 and 20151BBE50006)~~
文摘Catalytic oxidation of formaldehyde (HCHO) is the most efficient way to purify indoor air of HCHO pollutant. This work investigated rare earth La‐doped Pt/TiO2 for low concentration HCHO oxidation at room temperature. La‐doped Pt/TiO2 had a dramatically promoted catalytic performance for HCHO oxidation. The reasons for the La promotion effect were investigated by N2 adsorption, X‐raydiffraction, CO chemisorption, X‐ray photoelectron spectroscopy, transmission electron microscopy(TEM) and high‐angle annular dark field scanning TEM. The Pt nanoparticle size was reduced to 1.7nm from 2.2 nm after modification by La, which led to higher Pt dispersion, more exposed activesites and enhanced metal‐support interaction. Thus a superior activity for indoor low concentrationHCHO oxidation was obtained. Moreover, the La‐doped TiO2 can be wash‐coated on a cordieritemonolith so that very low amounts of Pt (0.01 wt%) can be used. The catalyst was evaluated in asimulated indoor HCHO elimination environment and displayed high purifying efficiency and stability.It can be potentially used as a commercial catalyst for indoor HCHO elimination.
文摘The effect of rare earth element yttrium on the high temperature oxidation resistance of a directionally solidified Ni-base superalloy was studied with scanning electron microscopy(SEM), energy dispersive spectrum(EDS)and X-ray diffraction(XRD)techniques. The results show that the oxidation resistance of the alloy is substantially improved by adding proper amount of yttrium.
文摘High temperature oxidation behaviors of FGH96 P/M superaUoy have been studied in air at temperatures ranging from 600 to 1000℃. By means of isothermal oxidation testing, X-ray diffraction, SEM （scanning electron microscopy）, and EDS （energy dispersive X-ray spectroscopy） analyses, the oxidation kinetics as well as the composition and morphology of scales were investigated. Thermodynamic calculations were used to explain the oxidation mechanism. The results showed that as the oxidation temperature increased, the oxidation rate, the scale thickness, and scale spallation increased. FGH96 P/M superalloy exhibits good oxidation resistance at temperature below 800℃. The oxidation kinetics follows an approximately parabolic rate law, and the oxide layer was mainly composed of Cr2O3 TiO2 and a little amount of NiCr2O4. The oxidation is controlled by the transmission of chromium. titanium, and oxygen through the oxide scale.
基金the Fundamental Research Program of the Korea Institute of Materials Science(Grant No.PNK5520)Korea Institute for Advancement of Technology(KIAT)grant funded by the Korea Government(MOTIE)(P0002007,The Competency Development Program for Industry Specialist)。
文摘The present study investigated the effect of as-built and post heat-treated microstructures of IN738LC alloy fabricated via selective laser melting process on high temperature oxidation behavior.The as-built microstructure showed fine cell and columnar structure due to high cooling rate.Ti element segregation was observed in inter-cell/inter-columnar area.After post heat-treatment,the initially-observed cell structure disappeared,instead bimodal Ni_3(Al,Ti)particles formed.High temperature(1273 K and 1373 K)oxidation test results showed parabolic oxidation curves regardless of temperature and initial microstructure.The as-built IN738LC fabricated via the selective laser melting process displayed oxidation resistance similar to or slightly better than that of IN738LC fabricated via wrought or cast process.Heat-treated SLM IN738LC,although had similar oxidation weight-gain values to those of the SLM asbuilt material at 1273K,showed relatively better oxidation resistance at 1373 K.Bimodal Ni_3(Al,Ti)precipitate formed in the post heat treatment changed the local chemical composition,thereby led to changes in alumina former/chromia former location and fraction on the alloy surface.It was concluded that in heat-treated IN738LC increased alumina former fraction was found,and this resulted in excellent oxidation resistance and relatively low weight-gain.
基金financially supported by the National Key Research and Development Program of China(No.2012AA03A501)。
文摘Inconel 600 alloy is widely utilized for high temperature environment application due to the corresponding good oxidation and corrosion resistance properties.In order to estimate the high temperature oxidation resistance of Inconel 600 alloy at various temperatures,the oxidation weight gain of all specimens was measured and fitted for the curve at the temperatures of 700,800 and 900 ℃ for exposure time of 100 h.The surface morphology and the component of the oxide film were analyzed by scanning electron microscopy(SEM),energy-dispersive spectroscopy(EDS) and X-ray diffraction(XRD).The results indicate that the high temperature oxidation resistance of Inconel 600 alloy is excellent blew 800℃ due to the oxidation kinetic curves at different temperatures corresponding to the parabola dynamic rules.This means that the oxidation film protects the substrate well.The dense oxide layer formation containing Cr_(2)O_(3) and NiCr_(2)O_(4) at 700 and 800 ℃ and MnCr_(2)O_(4) at 900 ℃,respectively,is the main reason for the good oxidation resistance.In contrast,the oxide layer peels off easily under applied force as the temperature increases beyond 800℃, on account of the complicated compositions of the oxide film and the binding force between the oxide layer and the substrate weakening.Corresponding oxidation mechanism is expected to be understood and the oxidation resistance of Inconel 600 alloy is improved through binding force enhancement.
文摘The effect of Si on the high temperature oxidation behavior of the 30Cr13 martensitic stainless steels was investigated. The underlying mechanism was further discussed by oxidation kinetics curves, scanning electron microscopy （SEM） and X-ray diffraction （XRD） analysis. It was ob- served that the addition of Si can significantly reduce the mass gain per unit area and the oxidation rate of the experimental steels. With the increase of Si content, the film surface composed of the wheat-like oxides turned into the small granular oxides after oxidation for 120 h. The SiO_2 film formed on the metal substrate inhibited the outward diffusion of the metal cation and the inward diffusion of the oxygen anion; thus, the high temperature oxidation resistance was enhanced.
基金support from the National Natural Science Foundation of China (No.51074159)The Graduate Scientific Research Innovation Programme of Jiangsu Province Ordinary University (No. CXZZ12_0957)
文摘Fourier transform infrared spectroscopy(FTIR) and constant heating rate experiments were performed to study the low temperature oxidation of coal treated by an ionic liquid,1-allyl-3-methylimidazolium chloride.The inerting effect of the ionic liquid toward the low temperature oxidation process is discussed.The results show that:(1) The hydroxyl content associated with hydrogen bonds,the aliphatic methyl content,the methylene group content,and the ether oxygen bond content are reduced in the treated coal.At the same time the content of aromatic C@C bonds is constant but these chemical bonds weaken and some substituted aromatic hydrocarbon content increases while other types decrease.This demonstrates that(AMIm)Cl dissolves and destroys the coal surface microstructure;(2) The oxygen consumption of the treated coal is less than what is seen in raw coal.The CO,CO 2,C 2 H 4,and C 2 H 6 content from the treated coal is reduced compared to the untreated coal;(3) The apparent activation energy for the oxidizing reaction is different in the treated and raw coals.Micro-structural changes and macroscopic gas production allow us to conclude that(AMIm)Cl can effectively inhibit low temperature oxidation of coal.
基金Project supported by the the Foundation of Beijing Jiaotong University(KCRC14002536)
文摘In high temperature oxidation environment, the oxidation reaction will induce variations in material parameters, such as Young's modulus, thermal expansion coefficient (CTE), coefficient of oxygen diffusion (COD), etc. The oxidation -induced material parameter variations should be considered in high temperature mechanical analysis. In this paper, high temperature oxidation behavior of an oxide film/metal substrate system was investigated through a modified phase field approach. The oxidative stress and oxidation weight gain induced by high temperature oxidation were studied. Effects of Young's modulus, COD and CTE on oxidative stress in the oxide film were studied particularly. The simulation results showed that a better agreement with the experimental results could be obtained when considering the oxidation -induced material parameter variations in the high temperature mechanical analysis of oxide film/metal substrate system. The simulation results demonstrated that oxidative stress and oxidation weight gain were more sensitive to the variation of Young's modulus than to the variations of COD and CTE.
文摘The effect of a sputtered Ti-48AI-8Cr-2Ag (at. pct) coating on the oxidation resistance of the cast Ti-46.5AI-5Nb (at. pct) alloy was investigated in air at 1000-1100℃. Hot corrosion in molten 75 wt pct Na2SO4+25 wt pct K2SO4 was investigated at 900℃. The scale on the cast TiAINb tends to spall in air, while the scale on coating is very adherent. The sputtered Ti-48AI-8Cr-2Ag coating remarkably improved high temperature oxidation resistance of the cast Ti-46.5AI-5Nb alloy because of the formation of an adherent Al2O3 scale. Due to the inward diffusion of Cr, Kirkendall voids were found at the coating/substrate interface. TiAICrAg coating provided excellent hot corrosion resistance for TiAINb alloy in molten 75 wt pct Na2SO4+25 wt pct K2S04 at 900℃ due to the formation of a continuous Al_2O_3 scale.
基金Item Sponsored by National High Technology Research and Development Program of China(2007AA03A228)
文摘Oxidation rates and scale/steel interface configuration of 9Ni steels were investigated at 1000--1 250 ℃ in air. The results revealed that Cu addition caused high temperature oxidation resistance to deteriorate. High tempera ture oxidation rates increased and scale/steel interface configuration became complicated due to Cu addition. Scale/ steel interface appeared to be network above certain temperature. Temperature required to form network scale/steel interface dropped more than 100 ℃ for 1.5% Cu-containing steel. （Fe,Ni,Cu）x Oy in inner oxidation layer dissocia ted to Fe-Ni-Cu phase and released active oxygen which can react with base steel easily. So the inner oxidation layer became the second source of oxidizing agent besides atmosphere. Internal stress at austenite grain boundary caused local oxide to fragment. So the scale/steel interface appeared to be network. Liquid Si-rich phase formed at sufficient ly high temperature. Penetration of the liquid Si-rich phase along austenite grain enhanced austenite grain oxidizing.
基金Project 50474067 supported by National Natural Science Foundation of China
文摘By analyzing previous studies on activation energy of coal oxidation at low temperatures, a theoretical calculation model of apparent activation energy is established. Yield of CO is measured by using the characteristic detector of coal oxidation at 30-90 ℃. The impact of parameters, such as airflow and particle size, on activation energies is analyzed. Finally, agreement was obtained between activation energies and the dynamic oxygen absorbed in order to test the accuracy of the model. The results show that： 1） a positive exponential relation between concentration of CO and temperature in the process of the experiment is obtained： increases are almost identical and the initial CO is low; 2） the apparent activation energies increase gradually with the sizes of particle at the same airflow, but the gradients increase at a decreasing rate; 3） the apparent activation energies increase linearly with airflow. For the five coal particles, the differences among the energies are relatively high when the airflow was low, but the differences were low when the airflow was high; 4） the optimum sizes of particle, 0.125-0.25 ram, and the optimum volume of airflow, 100 mL/min, are determined from the model; 5） the apparent activation energies decrease with an increase in oxygen absorbed. A negative exponential relation between the two is obtained,
基金funded by the National Key Research and Development Program of China (2018YFE0104200)National Natural Science Foundation of China (51875310, 52175274, 82172065)Tsinghua Precision Medicine Foundation
文摘Laser powder bed fusion(L-PBF)has been employed to additively manufacture WE43 magnesium(Mg)alloy biodegradable implants,but WE43 L-PBF samples exhibit excessively rapid corrosion.In this work,dense WE43 L-PBF samples were built with the relativity density reaching 99.9%.High temperature oxidation was performed on the L-PBF samples in circulating air via various heating temperatures and holding durations.The oxidation and diffusion at the elevated temperature generated a gradient structure composed of an oxide layer at the surface,a transition layer in the middle and the matrix.The oxide layer consisted of rare earth(RE)oxides,and became dense and thick with increasing the holding duration.The matrix was composed ofα-Mg,RE oxides and Mg_(24)RE_(5) precipitates.The precipitates almost disappeared in the transition layer.Enhanced passivation effect was observed in the samples treated by a suitable high temperature oxidation.The original L-PBF samples lost 40%weight after 3-day immersion in Hank’s solution,and broke into fragments after 7-day immersion.The casted and solution treated samples lost roughly half of the weight after 28-day immersion.The high temperature oxidation samples,which were heated at 525℃ for 8 h,kept the structural integrity,and lost only 6.88%weight after 28-day immersion.The substantially improved corrosion resistance was contributed to the gradient structure at the surface.On one hand,the outmost dense layer of RE oxides isolated the corrosive medium;on the other hand,the transition layer considerably inhibited the corrosion owing to the lack of precipitates.Overall,high temperature oxidation provides an efficient,economic and safe approach to inhibit the corrosion of WE43 L-PBF samples,and has promising prospects for future clinical applications.
基金financially supported by the National Natural Science Foundation of China(No.51871051)。
文摘Self-lubricating composites(SLCs)are widely used in the fields of aerospace and marine,but the conventional NiCr matrix SLCs with sulfide as solid lubricant often suffer from low wear resistance at high temperatures.In view of its high affinity with oxygen and also the high oxidation rate,appropriate amount of nano Ti was added to NiCr-WS_(2)composites prepared by spark plasma sintering(SPS)to adjust the oxidation behavior and surface texture.When exposed to high temperature,Ti was preferentially oxidized in comparison to Ni and Cr,resulting in abundant TiO_(2)protrusions and microdimples on the surface,i.e.in situ surface texturing.Besides,TiO_(2)was of high chemical activity and readily to react with other oxide debris during high temperature sliding process to form compounds of NiTiO_(3)and CrTi_(2)O_(5).The high chemical activity of oxide debris that was conducive to sintering,combining with the special surface texture that stores as many wear debris as possible,promoted the rapid formation of a protective glaze layer on the sliding surface.The NiCr-WS_(2)-Ti composite exhibited low friction coefficient but high wear resistance at elevated temperatures.Especially at 800℃,it presented a wear rate of as low as(2.1±0.3)×10^(-5)mm^3N-1m^(-1),accounting for only 2.7%of that of NiCr-WS_(2)composite.
文摘The interfacial behavior of sulfur and yttrium in the yttrium modified Ni 3Al based alloy IC6 during oxidation at 1100 ℃ was analyzed by X ray line scan of electron probe microstructural analysis(EPMA). The results show that the migration and segregation of sulfur to the interface between oxide scale and the substrate at high temperature is retarded owing to the presence of yttrium. This is attributed to the desulfurization by yttrium in the melt and the trapping of sulfur by yttrium rich phases during oxidation, which leads to improving the coherence between oxide scale and substrate. Another reason of increasing the high temperature oxidation resistance of alloy IC6 by the addition of yttrium is that yttrium migrates to the grain boundaries of oxides during oxidation and hence improve their strength. This results in the transformation of the oxide scale spallation cracks from intergranular cracks for alloy without yttrium to transgranular ones for yttrium modified alloy.
基金National Key Research and Development Program of China(No.2018YFE0104200)National Natural Science Foundation of China(Nos.52175274,82172065,51875310)Tsinghua Precision Medicine Foundation and Tsinghua-Toyota Joint Research Fund.
文摘Laser powder bed fusion(L-PBF)has been used to fabricate biodegradable Mg implants of WE43 alloy,but the degradation is too fast compared with the term bone reconstruction.Previous studies show that high temperature oxidation(HTO)can successfully inhibit the degradation of WE43 alloy.In this work,the influence of HTO on L-PBF samples of WE43 alloy was investigated regarding tensile,compressive,and abrasive resistance,as well as in vitro cytotoxicity,cell proliferation,hemolysis,and osteogenesis.Compared with the as-built L-PBF samples,HTO increased grain size and grain texture,stabilized and coarsened precipitates,and caused discontinuous static recrystallization in the matrix.The oxide layer at the surface of the HTO samples improved surface roughness,hydrophilia,hardness,and abrasive resis-tance.The tensile strength decreased slightly from 292 to 265 MPa,while the elongation substantially increased from 10.97%to 16.58%after HTO.The in vitro cell viability,cell proliferation,hemolysis,and osteogenic effect were considerably enhanced due to the improvement of surface quality and the initial inhibition of excessive Mg^(2+)releasement.Overall,HTO is of great benefit to the surface performance,ductility,and biocompatibility of WE43 alloy fabricated by L-PBF for biodegradable applications.
