Optimizing the output power of a photovoltaic panel improves the efficiency of a solar driven energy system. The maximum output power of a photovoltaic panel depends on atmospheric conditions, such as (direct solar ra...Optimizing the output power of a photovoltaic panel improves the efficiency of a solar driven energy system. The maximum output power of a photovoltaic panel depends on atmospheric conditions, such as (direct solar radiation, air pollution and cloud movements), load profile and the tilt and orientation angles. This paper describes an experimental analysis of maximizing output power of a photovoltaic panel, based on the use of existing equations of tilt angles derived from mathematical models and simulation packages. Power regulation is achieved by the use of a DC-DC converter, a fixed load resistance and a single photovoltaic panel. A data logger is used to make repeated measurements which ensure reliability of the results. The results of the paper were taken over a four month period from April through July. The photovoltaic panel was set to an orientation angle of 0? with tilt angles of 16?, 26? and 36?. Preliminary results indicate that tilt angles between 26? and 36? provide optimum photovoltaic output power for winter months in South Africa.展开更多
The electromagnetic torque and speed in Switched Reluctance Motor (SRM) greatly depend on the excitation parametersi.e. turn-on angle, turn-off angle, dwell angle and magnitude of the phase currents of its phases...The electromagnetic torque and speed in Switched Reluctance Motor (SRM) greatly depend on the excitation parametersi.e. turn-on angle, turn-off angle, dwell angle and magnitude of the phase currents of its phases. At lower speeds, a change in the current contributes the torque requirement which can be achieved either by voltage control (pulse width modulation) or instantaneous current control techniques. At high speeds, due to high back EMF, the regulation of current is crucial and achieved with the control of switching angles of phases. This type of control is referred as average torque control, where the torque is averaged over one stroke (2π/N<sub>r</sub>). With constant dwell angle, advancing the phase angle influences the current into the phase winding at minimum inductance position. It has more time to get the current out of the phase winding before the rotor reaches the negative inductance slope. To maintain the speed of the motor at different load conditions, the turn-on and turn-off angles are adaptively varied. The change in dwell angle may be required where the turn-on and turn-off angle may not be sufficient to reach the required speed. In this paper, a new algorithm is proposed for self tuning of switching parameters of SRM. The proposed algorithm is simulated in MATLAB-Simulink and experimentally validated with Field Programmable Gated Array (FPGA) using MATLAB- system generator environment.展开更多
Accurate quantification of the spin–orbit torques(SOTs) is critical for the identification and applications of new spin-orbitronic effects. One of the most popular techniques to quantify the SOTs is the “switching a...Accurate quantification of the spin–orbit torques(SOTs) is critical for the identification and applications of new spin-orbitronic effects. One of the most popular techniques to quantify the SOTs is the “switching angle shift”, where the applied direct current is assumed to shift, via domain wall depinning during anti-domain expansion, the switching angle of a perpendicular magnetization in a linear proportional manner under a large rotating magnetic field. Here, we report that, for the most commonly employed perpendicular magnetization heterostructures in spintronics(e.g., those based on FeCoB, Co, and Co/Ni multilayers), the switching angle shift considerably misestimates the SOT within the domain wall depinning analysis of the slope of linear-in-current scaling and may also have a non-zero residual value at zero direct current. Our experiments and simulations unveil that the switching angle shift is most likely dominated by chiral asymmetric nucleation rather than expansion of anti-domains. The in-plane field from external magnets and current-induced SOTs lowers the perpendicular nucleation field and thus reduces the required switching angle, ultimately leading to an underestimation of SOTs by domain wall depinning analysis. These results have advanced our understanding of magnetization switching in spintronic devices.展开更多
The Cenozoic geological hallmark of Western Yunnan is the characteristic voluminous Late Cretaceous-Eocene granites;however, their geological background and petrogenesis have not been well constrained and elucidated. ...The Cenozoic geological hallmark of Western Yunnan is the characteristic voluminous Late Cretaceous-Eocene granites;however, their geological background and petrogenesis have not been well constrained and elucidated. In this study, we present new zircon U-Pb dating, along with geochemical and Sr-Nd-Hf isotopic data for granites from the Tengchong–Lianghe granitoid belt(as abbreviated to Tengliang belt) and West Yingjiang batholiths from the Tengchong block. The mineralogical and geochemical features of the Tengliang granites and the West Yingjiang batholiths are ascribed to aluminous S-type granites and weak peraluminous I-type, respectively. Zircon U-Pb analyses yielded consistent ages ranging from 67.5 Ma, 68.4 Ma and 66.2 Ma from the Tengliang granitoid belt and 50.4 Ma to 60.8 Ma for three samples from the west Yingjiang batholiths. The Tengliang granites were emplaced during the Late Cretaceous(68-66 Ma) and demonstrate negative ε_(Hf)(t) values(-24 to-4) and initial ~(87)Sr/~(86)Sr ratios of 0.7101–0.7139 and significant negative ε_(Nd)(t) values from-8.91 to-13.2, indicating a Proterozoic sedimentary source or enriched components. The hornblende-bearing I-type granites from West Yingjiang are characterized by lower initial ~(87)Sr/~(86)Sr ratios of 0.7076–0.7106, compared to Tengliang granite and negative whole-rock ε_(Nd)(t) values from-4.0 to-11.9. The early Eocene west Yingjiang gneissic granites show wide ranges of ε_(Hf)(t) values from +7.4 to-8.5 and T_(2DM) of 1.30–0.65 Ga, indicating partial melting of ancient crust with contributions of depleted mantle materials. In combination with the regional background and previous studies, we propose that such a spatio-temporal distribution of the Tengchong granitoid belt might be related to the rollback or angleswitching of the Neo-Tethyan subducting slab. This study sheds new light on the evolutionary history of the Tengchong block.展开更多
The optimum design of the highway excavation slope angle is one of the most important problems to the highway construction and to the slope improvement. The Dawu Section of Jingzhu (Beijing Zhuhai) Highway is taken a...The optimum design of the highway excavation slope angle is one of the most important problems to the highway construction and to the slope improvement. The Dawu Section of Jingzhu (Beijing Zhuhai) Highway is taken as an example to illustrate the study method for excavation slope angle design. The analysis of the engineering condition from different angles with different factors shows that the stability of the slope is calculated by using residual pushing force and the Sarma method. Then the sensitive analysis of the slope stability is conducted by using residual pushing force method. Finally, the optimum angle of design is presented on the precondition of ensuring the whole stability of slope and the economic reasonability. The study results show that the most sensitive factors are the shear strength parameter and the seismic force, and that the optimum excavation slope angle is 60°.展开更多
Solar collectors can provide clean, renewable, and domestic energy. The tilt angle and horizontal direction of solar collectors significantly affect its efficiency. There are many good methods to search the optimum ti...Solar collectors can provide clean, renewable, and domestic energy. The tilt angle and horizontal direction of solar collectors significantly affect its efficiency. There are many good methods to search the optimum tilt angle and horizontal direction to realize the maximum total radiation on the solar collector within a particular day or a specific period. However, it is hard to realize it when solar collectors are placed under obstacle’s shadows;especially when some obstacles, such as trees, have irregular shapes. This paper presents algorithms to achieve the best tilt angle and horizontal direction for solar collector’s performance under the free-form surfaces 3D obstacle’s shadow. The solution process is composed of 4 steps. First, it creates a 3D scene, in which a unique color is given to the solar collector. Second, it employs orthographic projection from the point of view to get an image of the scene. Third, the number of pixels is used to represent the efficiency of the solar collector by counting the pixels of the unique color. Fourth, the efficiency of solar collector in each direction in a period of time is calculated with many images to further select the best direction.展开更多
In this paper a simulation to maximize the global solar radiation on a sloped collecting surface was applied to typical latitudes in the area of southern Italy, to calculate the optimum tilt angle of solar panels on b...In this paper a simulation to maximize the global solar radiation on a sloped collecting surface was applied to typical latitudes in the area of southern Italy, to calculate the optimum tilt angle of solar panels on building structures or large photovoltaic power plants located in that geographical area. Indeed, the area of southern Italy and in particular Sicily and Calabria are the top of European locations for acquiring solar energy. Some models of diffuse solar irradiance were taken into account to determine panels inclinations that maximized the impinging solar radiation by means of global horizontal solar radiation data provided from the Italian Institute of ENEA (Italy). An algorithm was used for the simulation providing a set of tilt angles for each latitude. The optimum tilt angle values obtained from the simulation resulted to be strictly related to the model of diffuse solar radiation that was used. Indeed, the disagreement between the values obtained using anisotropic models of diffuse solar radiation and those obtained from the isotropic model resulted to decrease significantly with increasing solar declination, showing that the isotropic model can be reliable only in summer months.展开更多
The present study reflects upon the results of substantial program of two-dimensional Finite Element Method （FEM） numerical analyses of the open pit that links to slope angle optimization associated with the safety ...The present study reflects upon the results of substantial program of two-dimensional Finite Element Method （FEM） numerical analyses of the open pit that links to slope angle optimization associated with the safety factor of the pit slope of a coal mine in Bangladesh. In the present analyses, two types of models have been presented. The first model estimates safety factor without seismic effect on the overall pit slope of the model; the second model incorporates safety factor with seismic stability of the model. The calculated optimum slope angle of the first model is 31% with a rational safety factor of 1.51, prior to the seismic effect. However, the value is reduced to 0.93, 0.82, and 0.72, after we applies the seismic effect in the second model with M6, M6.5, and M7, respectively. Finally, our modeling results emphasize that for the case of the proposed Phulbari coalmine, there is extremely high prospect for causing massive slope failure along the optimum pit slope angle with 31% if the mine area felt seismic shaking, like the Sikkim （in northern India） earthquake with M6.9 on September 18, 2011.展开更多
Switched reluctance motor(SRM)usually adopts Direct Instantaneous Torque Control(DITC)to suppress torque ripple.However,due to the fixed turn-on angle and the control mode of the two-phase exchange region,the conventi...Switched reluctance motor(SRM)usually adopts Direct Instantaneous Torque Control(DITC)to suppress torque ripple.However,due to the fixed turn-on angle and the control mode of the two-phase exchange region,the conventional DITC control method has low adaptability in different working conditions,which will lead to large torque ripple.For this problem,an improved DITC control method based on turn-on angle optimization is proposed in this paper.Firstly,the improved BP neural network is used to construct a nonlinear torque model,so that the torque can be accurately fed back in real time.Secondly,the turn-on angle optimization algorithm based on improved GRNN neural network is established,so that the turn-on angle can be adjusted adaptively online.Then,according to the magnitude of inductance change rate,the two-phase exchange region is divided into two regions,and the phase with larger inductance change rate and current is selected to provide torque in the sub-regions.Finally,taking a 3-phase 6/20 SRM as example,simulation and experimental verification are carried out to verify the effectiveness of this method.展开更多
The various configurations of multilevel inverter involve the use of more numbers of switching devices, energy storage devices and/or unidirectional devices. Each switching unit necessitates the add-on driver circuit ...The various configurations of multilevel inverter involve the use of more numbers of switching devices, energy storage devices and/or unidirectional devices. Each switching unit necessitates the add-on driver circuit for proper functionality. Cascaded H-Bridge Multilevel Inverter requires overlapped switching pulses for the switching devices in positive and negative arms of the bridge which may lead to short circuit during the device failure. This work addresses the problems in different configurations of multilevel inverter by using reduced number of switching and energy storage devices and driver circuits. In the present approach Single Switch is used for each stair case positive output and single H-Bridge for phase reversal. Driver circuits are reduced by using the property of body diode of the MOSFET. Switching pulses are generated by Arduino Development Board. The circuit is simulated using Matlab. More so, through experimental means, it is physically tested and results are analyzed for the 5-step inverter and thereby simulation is fully validated. Consequently, cycloconverter operation of the circuit is simulated using Matlab. Moreover, half bridge configuration of the multilevel inverter is also analyzed for high frequency induction heating applications.展开更多
文摘Optimizing the output power of a photovoltaic panel improves the efficiency of a solar driven energy system. The maximum output power of a photovoltaic panel depends on atmospheric conditions, such as (direct solar radiation, air pollution and cloud movements), load profile and the tilt and orientation angles. This paper describes an experimental analysis of maximizing output power of a photovoltaic panel, based on the use of existing equations of tilt angles derived from mathematical models and simulation packages. Power regulation is achieved by the use of a DC-DC converter, a fixed load resistance and a single photovoltaic panel. A data logger is used to make repeated measurements which ensure reliability of the results. The results of the paper were taken over a four month period from April through July. The photovoltaic panel was set to an orientation angle of 0? with tilt angles of 16?, 26? and 36?. Preliminary results indicate that tilt angles between 26? and 36? provide optimum photovoltaic output power for winter months in South Africa.
文摘The electromagnetic torque and speed in Switched Reluctance Motor (SRM) greatly depend on the excitation parametersi.e. turn-on angle, turn-off angle, dwell angle and magnitude of the phase currents of its phases. At lower speeds, a change in the current contributes the torque requirement which can be achieved either by voltage control (pulse width modulation) or instantaneous current control techniques. At high speeds, due to high back EMF, the regulation of current is crucial and achieved with the control of switching angles of phases. This type of control is referred as average torque control, where the torque is averaged over one stroke (2π/N<sub>r</sub>). With constant dwell angle, advancing the phase angle influences the current into the phase winding at minimum inductance position. It has more time to get the current out of the phase winding before the rotor reaches the negative inductance slope. To maintain the speed of the motor at different load conditions, the turn-on and turn-off angles are adaptively varied. The change in dwell angle may be required where the turn-on and turn-off angle may not be sufficient to reach the required speed. In this paper, a new algorithm is proposed for self tuning of switching parameters of SRM. The proposed algorithm is simulated in MATLAB-Simulink and experimentally validated with Field Programmable Gated Array (FPGA) using MATLAB- system generator environment.
基金supported by the National Key Research and Development Program of China (Grant No.2022YFA1204000)partly by the National Natural Science Foundation of China (Grant Nos.12274405,12304155,and 12393831)the Beijing Natural Science Foundation (Grant No.Z230006)。
文摘Accurate quantification of the spin–orbit torques(SOTs) is critical for the identification and applications of new spin-orbitronic effects. One of the most popular techniques to quantify the SOTs is the “switching angle shift”, where the applied direct current is assumed to shift, via domain wall depinning during anti-domain expansion, the switching angle of a perpendicular magnetization in a linear proportional manner under a large rotating magnetic field. Here, we report that, for the most commonly employed perpendicular magnetization heterostructures in spintronics(e.g., those based on FeCoB, Co, and Co/Ni multilayers), the switching angle shift considerably misestimates the SOT within the domain wall depinning analysis of the slope of linear-in-current scaling and may also have a non-zero residual value at zero direct current. Our experiments and simulations unveil that the switching angle shift is most likely dominated by chiral asymmetric nucleation rather than expansion of anti-domains. The in-plane field from external magnets and current-induced SOTs lowers the perpendicular nucleation field and thus reduces the required switching angle, ultimately leading to an underestimation of SOTs by domain wall depinning analysis. These results have advanced our understanding of magnetization switching in spintronic devices.
基金the financial support provided by the open fund from the Key Laboratory of Deep-Earth Dynamics of the Ministry of Natural Resources, Institute of Geology, as well as Chinese Academy of Geological Sciences (Grant No. J1901-16)the State Key Laboratory for Mineral Deposits Research, Nanjing University (Grant No. 2020-LAMD-K04)+1 种基金the National Natural Science Foundation of China (Grant No. 41403029)The support provided by the China Scholarship Council (CSC) during a visit to the University of Arizona (201709110012)。
文摘The Cenozoic geological hallmark of Western Yunnan is the characteristic voluminous Late Cretaceous-Eocene granites;however, their geological background and petrogenesis have not been well constrained and elucidated. In this study, we present new zircon U-Pb dating, along with geochemical and Sr-Nd-Hf isotopic data for granites from the Tengchong–Lianghe granitoid belt(as abbreviated to Tengliang belt) and West Yingjiang batholiths from the Tengchong block. The mineralogical and geochemical features of the Tengliang granites and the West Yingjiang batholiths are ascribed to aluminous S-type granites and weak peraluminous I-type, respectively. Zircon U-Pb analyses yielded consistent ages ranging from 67.5 Ma, 68.4 Ma and 66.2 Ma from the Tengliang granitoid belt and 50.4 Ma to 60.8 Ma for three samples from the west Yingjiang batholiths. The Tengliang granites were emplaced during the Late Cretaceous(68-66 Ma) and demonstrate negative ε_(Hf)(t) values(-24 to-4) and initial ~(87)Sr/~(86)Sr ratios of 0.7101–0.7139 and significant negative ε_(Nd)(t) values from-8.91 to-13.2, indicating a Proterozoic sedimentary source or enriched components. The hornblende-bearing I-type granites from West Yingjiang are characterized by lower initial ~(87)Sr/~(86)Sr ratios of 0.7076–0.7106, compared to Tengliang granite and negative whole-rock ε_(Nd)(t) values from-4.0 to-11.9. The early Eocene west Yingjiang gneissic granites show wide ranges of ε_(Hf)(t) values from +7.4 to-8.5 and T_(2DM) of 1.30–0.65 Ga, indicating partial melting of ancient crust with contributions of depleted mantle materials. In combination with the regional background and previous studies, we propose that such a spatio-temporal distribution of the Tengchong granitoid belt might be related to the rollback or angleswitching of the Neo-Tethyan subducting slab. This study sheds new light on the evolutionary history of the Tengchong block.
基金theNationalNaturalScienceFoundationofChina (No .40 0 72 0 85 )
文摘The optimum design of the highway excavation slope angle is one of the most important problems to the highway construction and to the slope improvement. The Dawu Section of Jingzhu (Beijing Zhuhai) Highway is taken as an example to illustrate the study method for excavation slope angle design. The analysis of the engineering condition from different angles with different factors shows that the stability of the slope is calculated by using residual pushing force and the Sarma method. Then the sensitive analysis of the slope stability is conducted by using residual pushing force method. Finally, the optimum angle of design is presented on the precondition of ensuring the whole stability of slope and the economic reasonability. The study results show that the most sensitive factors are the shear strength parameter and the seismic force, and that the optimum excavation slope angle is 60°.
文摘Solar collectors can provide clean, renewable, and domestic energy. The tilt angle and horizontal direction of solar collectors significantly affect its efficiency. There are many good methods to search the optimum tilt angle and horizontal direction to realize the maximum total radiation on the solar collector within a particular day or a specific period. However, it is hard to realize it when solar collectors are placed under obstacle’s shadows;especially when some obstacles, such as trees, have irregular shapes. This paper presents algorithms to achieve the best tilt angle and horizontal direction for solar collector’s performance under the free-form surfaces 3D obstacle’s shadow. The solution process is composed of 4 steps. First, it creates a 3D scene, in which a unique color is given to the solar collector. Second, it employs orthographic projection from the point of view to get an image of the scene. Third, the number of pixels is used to represent the efficiency of the solar collector by counting the pixels of the unique color. Fourth, the efficiency of solar collector in each direction in a period of time is calculated with many images to further select the best direction.
文摘In this paper a simulation to maximize the global solar radiation on a sloped collecting surface was applied to typical latitudes in the area of southern Italy, to calculate the optimum tilt angle of solar panels on building structures or large photovoltaic power plants located in that geographical area. Indeed, the area of southern Italy and in particular Sicily and Calabria are the top of European locations for acquiring solar energy. Some models of diffuse solar irradiance were taken into account to determine panels inclinations that maximized the impinging solar radiation by means of global horizontal solar radiation data provided from the Italian Institute of ENEA (Italy). An algorithm was used for the simulation providing a set of tilt angles for each latitude. The optimum tilt angle values obtained from the simulation resulted to be strictly related to the model of diffuse solar radiation that was used. Indeed, the disagreement between the values obtained using anisotropic models of diffuse solar radiation and those obtained from the isotropic model resulted to decrease significantly with increasing solar declination, showing that the isotropic model can be reliable only in summer months.
文摘The present study reflects upon the results of substantial program of two-dimensional Finite Element Method （FEM） numerical analyses of the open pit that links to slope angle optimization associated with the safety factor of the pit slope of a coal mine in Bangladesh. In the present analyses, two types of models have been presented. The first model estimates safety factor without seismic effect on the overall pit slope of the model; the second model incorporates safety factor with seismic stability of the model. The calculated optimum slope angle of the first model is 31% with a rational safety factor of 1.51, prior to the seismic effect. However, the value is reduced to 0.93, 0.82, and 0.72, after we applies the seismic effect in the second model with M6, M6.5, and M7, respectively. Finally, our modeling results emphasize that for the case of the proposed Phulbari coalmine, there is extremely high prospect for causing massive slope failure along the optimum pit slope angle with 31% if the mine area felt seismic shaking, like the Sikkim （in northern India） earthquake with M6.9 on September 18, 2011.
基金supported by National Natural Science Foundation of China under Grant 52167005Science and Technology Research Project of Jiangxi Provincial Department of Education under Grant GJJ200826。
文摘Switched reluctance motor(SRM)usually adopts Direct Instantaneous Torque Control(DITC)to suppress torque ripple.However,due to the fixed turn-on angle and the control mode of the two-phase exchange region,the conventional DITC control method has low adaptability in different working conditions,which will lead to large torque ripple.For this problem,an improved DITC control method based on turn-on angle optimization is proposed in this paper.Firstly,the improved BP neural network is used to construct a nonlinear torque model,so that the torque can be accurately fed back in real time.Secondly,the turn-on angle optimization algorithm based on improved GRNN neural network is established,so that the turn-on angle can be adjusted adaptively online.Then,according to the magnitude of inductance change rate,the two-phase exchange region is divided into two regions,and the phase with larger inductance change rate and current is selected to provide torque in the sub-regions.Finally,taking a 3-phase 6/20 SRM as example,simulation and experimental verification are carried out to verify the effectiveness of this method.
文摘The various configurations of multilevel inverter involve the use of more numbers of switching devices, energy storage devices and/or unidirectional devices. Each switching unit necessitates the add-on driver circuit for proper functionality. Cascaded H-Bridge Multilevel Inverter requires overlapped switching pulses for the switching devices in positive and negative arms of the bridge which may lead to short circuit during the device failure. This work addresses the problems in different configurations of multilevel inverter by using reduced number of switching and energy storage devices and driver circuits. In the present approach Single Switch is used for each stair case positive output and single H-Bridge for phase reversal. Driver circuits are reduced by using the property of body diode of the MOSFET. Switching pulses are generated by Arduino Development Board. The circuit is simulated using Matlab. More so, through experimental means, it is physically tested and results are analyzed for the 5-step inverter and thereby simulation is fully validated. Consequently, cycloconverter operation of the circuit is simulated using Matlab. Moreover, half bridge configuration of the multilevel inverter is also analyzed for high frequency induction heating applications.
