Electrochemical water splitting has long been considered an effective energy conversion technology for trans-ferring intermittent renewable electricity into hydrogen fuel,and the exploration of cost-effective and high...Electrochemical water splitting has long been considered an effective energy conversion technology for trans-ferring intermittent renewable electricity into hydrogen fuel,and the exploration of cost-effective and high-performance electrocatalysts is crucial in making electrolyzed water technology commercially viable.Cobalt phosphide(Co-P)has emerged as a catalyst of high potential owing to its high catalytic activity and durability in water splitting.This paper systematically reviews the latest advances in the development of Co-P-based materials for use in water splitting.The essential effects of P in enhancing the catalytic performance of the hydrogen evolution reaction and oxygen evolution reaction are first outlined.Then,versatile synthesis techniques for Co-P electrocatalysts are summarized,followed by advanced strategies to enhance the electrocatalytic performance of Co-P materials,including heteroatom doping,composite construction,integration with well-conductive sub-strates,and structure control from the viewpoint of experiment.Along with these optimization strategies,the understanding of the inherent mechanism of enhanced catalytic performance is also discussed.Finally,some existing challenges in the development of highly active and stable Co-P-based materials are clarified,and pro-spective directions for prompting the wide commercialization of water electrolysis technology are proposed.展开更多
The demand for underground space and sustainable energy has driven the need for underground structures.Large underground caverns,being an underground structure carrier,offers a feasible solution.However,the stability ...The demand for underground space and sustainable energy has driven the need for underground structures.Large underground caverns,being an underground structure carrier,offers a feasible solution.However,the stability analysis and optimization design of large underground caverns is always a great challenge due to the high geostress,complicated rock condition,and high sidewalls and large spans in size.By collecting and reviewing a large amount of relevant research literature from 1970 to 2023,the efforts on the advances in stability analysis methods and optimization design of large underground caverns are described,then the research trends in this field through keywords were found and typical deformation and break modes of large underground caverns with high geostress are summarized.The review reveals that stability analysis and optimization are the recent active research topics.There are seven typical deformation and break modes of large underground caverns under high geostress,four stability analysis methods and four theories of optimization design of large under-ground caverns.With the progress of science and technology and society,intelligent design,mechanized con-struction and greening construction are the development trend in this field.The research results can provide a constructive reference for the stability analysis and optimization design of large underground caverns under high geostress.展开更多
The advanced fin-shaped field-effect transistor(FinFET)technology offers higher integration density and stronger channel control capabilities,however,more complex process effects are also introduced which have signifi...The advanced fin-shaped field-effect transistor(FinFET)technology offers higher integration density and stronger channel control capabilities,however,more complex process effects are also introduced which have significant influence on device performance.To address these issues,we complete a design-technology co-optimization(DTCO)focused on FinFET,including both process-induced effect during gate formation and corresponding digital unit optimization design.The 14 nm Fin-FET complementary metal oxide semiconductor(CMOS)technology is used to illustrate the sensitivity of transistor perfor-mance to process-induced effect,specifically the poly pitch effect(PPE)and cut poly effect(CPE).Predictive technology com-puter aided design(TCAD)simulations have been carried out to evaluate the transistor performance in advance.Based on the results,optimizations in digital unit design is proposed.Fall delay of the digital unit inverter is decreased by 0.7%,and the rise delay is decreased by 2.1%.For multiple selector(MUX2NV),the delay decreases by 4.64%for rise and 3.56%for drop,respec-tively.展开更多
With the continuous advancement in topology optimization and additive manufacturing(AM)technology,the capability to fabricate functionally graded materials and intricate cellular structures with spatially varying micr...With the continuous advancement in topology optimization and additive manufacturing(AM)technology,the capability to fabricate functionally graded materials and intricate cellular structures with spatially varying microstructures has grown significantly.However,a critical challenge is encountered in the design of these structures–the absence of robust interface connections between adjacent microstructures,potentially resulting in diminished efficiency or macroscopic failure.A Hybrid Level Set Method(HLSM)is proposed,specifically designed to enhance connectivity among non-uniform microstructures,contributing to the design of functionally graded cellular structures.The HLSM introduces a pioneering algorithm for effectively blending heterogeneous microstructure interfaces.Initially,an interpolation algorithm is presented to construct transition microstructures seamlessly connected on both sides.Subsequently,the algorithm enables the morphing of non-uniform unit cells to seamlessly adapt to interconnected adjacent microstructures.The method,seamlessly integrated into a multi-scale topology optimization framework using the level set method,exhibits its efficacy through numerical examples,showcasing its prowess in optimizing 2D and 3D functionally graded materials(FGM)and multi-scale topology optimization.In essence,the pressing issue of interface connections in complex structure design is not only addressed but also a robust methodology is introduced,substantiated by numerical evidence,advancing optimization capabilities in the realm of functionally graded materials and cellular structures.展开更多
An optimization design was conducted for the shape of the pressure vessel with a thin-shell shell. During this process, the optimization calculation was performed with the aid of the genetic algorithm toolbox included...An optimization design was conducted for the shape of the pressure vessel with a thin-shell shell. During this process, the optimization calculation was performed with the aid of the genetic algorithm toolbox included in Matlab. Firstly, through the parametric modeling function of APDL, models such as arc-shaped, parabolic, elliptical, and those generated by the fitting curve command were successfully constructed. Meanwhile, the relevant settings of material properties were accomplished, and the static analysis was conducted. Secondly, the optimization calculation process was initiated using the genetic algorithm toolbox in Matlab. Eventually, through analysis and judgment, the model generated by the fitting curve command was relatively superior within the category of the best shape.展开更多
For effectively improving the overall performance of fire truck frame structure,and solving the complexity of previous methods in the frame optimization design process,the traditional grey relational grade ranking nee...For effectively improving the overall performance of fire truck frame structure,and solving the complexity of previous methods in the frame optimization design process,the traditional grey relational grade ranking needs to be improved.First,the first-order modal test was conducted to verify the validity of the initial frame model.Then,based on this model,a high-strength steel frame was designed to reduce deformation,maximum stress,and frame mass,and increase the fatigue life and the frequencies of the first bending modal and first torsional modal.Sixty groups of sample points were generated through Hammersley method.Subsequently,improved grey relational analysis with principal component analysis was proposed to realize the optimal design of the frame structure.Finally,the optimal combination of design parameters for the frame was obtained using the proposed method.Meanwhile,the optimized frame structure is found by comparing the models before and after optimization,and the mass is reduced by 14.8%.Moreover,the computational cost can be reduced by 135%when the proposed method is compared with the previous algorithm.Therefore,the proposed method can effectively improve the performance of the frame and improve the computational efficiency.展开更多
In order to improve the performance and service life of the Leningrader seal of the Stirling engine piston rod,interference,pre-load and friction coefficient were taken as influencing factors,and the curved surface re...In order to improve the performance and service life of the Leningrader seal of the Stirling engine piston rod,interference,pre-load and friction coefficient were taken as influencing factors,and the curved surface response method was adopted to reduce the contact stress of sealing surface and von Mises stress of the sealing sleeve as the response index,with the optimization goal of reducing wear and extending life.The above three key parameters are analyzed and optimized,the influence of each parameter on the sealing performance and service life is obtained,and the best combination scheme of the three is determined.The results show that the interaction between pre-tightening force and interference fit has the greatest impact on contact stress.The interaction between interference fit and friction coeffi-cient has the most significant effect on von Mises stress.The optimized parameters can reduce the maximum contact stress and maximum von Mises stress of the sealing sleeve by 26.3%and 20.6%,respectively,under a media pressure of 5-9 MPa.Test bench verification shows that the leakage of the optimized sealing device in 12 h is reduced by 0.44 cc·min^(-1)(1 cc=1 cm^(3)).The wear rate of the sealing sleeve is 1.08%before optimization and 0.45%after optimization,indicating that the optimized parameters in this paper are effective.展开更多
Aiming at the problems in current cam profile optimization processes, such as simple dynamics models, limited geometric accuracy and low design automatization level, a new dynamic optimization mode is put forward. Bas...Aiming at the problems in current cam profile optimization processes, such as simple dynamics models, limited geometric accuracy and low design automatization level, a new dynamic optimization mode is put forward. Based on the parameterization modeling technique of MSC. ADAMS platform, the different steps in current mode are reorganized, thus obtaining an upgraded mode called the ＂parameterized-prototype-based cam profile dynamic optimization mode＂. A parameterized prototype（PP） of valve mechanism is constructed in the course of dynamic optimization for cam profiles. Practically, by utilizing PP and considering the flexibility of the parts in valve mechanism, geometric accuracy and design automatization are improved.展开更多
The well number and the cavity length of 1.55μm wavelength In 1-x-y Ga y Al x As MQW DFB lasers are optimized using a simple model.A low threshold,maximum operating temperature of 550～560K,and high relaxat...The well number and the cavity length of 1.55μm wavelength In 1-x-y Ga y Al x As MQW DFB lasers are optimized using a simple model.A low threshold,maximum operating temperature of 550～560K,and high relaxation oscillation frequency of over 30GHz MQW DFB laser is presented.展开更多
Optimization design of hydraulic manifold blocks (HMB) is studied as acomplex solid spatial layout problem. Based on comprehensive research into structure features anddesign rules of HMB, an optimal mathematical model...Optimization design of hydraulic manifold blocks (HMB) is studied as acomplex solid spatial layout problem. Based on comprehensive research into structure features anddesign rules of HMB, an optimal mathematical model for this problem is presented. Usinghuman-computer cooperative genetic algorithm (GA) and its hybrid optitation strategies, integratedlayout and connection design schemes of HMB can be automatically optimized. An example is given totestify it.展开更多
Natural ice accretion on the lifting surface of an aircraft is detrimental to its aerodynamic performance, as it changes the effective streamlined body. The main focus of this work considers the optimization design of...Natural ice accretion on the lifting surface of an aircraft is detrimental to its aerodynamic performance, as it changes the effective streamlined body. The main focus of this work considers the optimization design of airfoils under atmospheric icing conditions for the Unmanned Aerial Vehicle(UAV). The ice formation process is simulated by the Eulerian approach and the three-dimensional Myers model. A three-equation turbulence model is implemented to accurately predict the stall performance of the iced airfoil. In recognition of the real atmospheric variability in the icing parameters, the medium volume diameter of supercooled water droplets is treated as an uncertainty with an assumed probability density function. A technique of polynomial chaos expansion is used to propagate the input uncertainty through the deterministic system. The numerical results show that the multipoint/multiobjective optimization strategy can efficiently improve both the ice tolerance and the cruise performance of an airfoil. The reason for the focus on robust optimization is that the ice angle of the optimized airfoil becomes less critical to the incoming flow.The optimized airfoils are applied to a UAV platform, in which the performance improvement and the relevant key flow feature are both preserved.展开更多
Comprehensive optimization design of serpentine nozzle with trapezoidal outlet was studied to improve its aerodynamic and electromagnetic scattering performance.Serpentine nozzles with different center offsets and dif...Comprehensive optimization design of serpentine nozzle with trapezoidal outlet was studied to improve its aerodynamic and electromagnetic scattering performance.Serpentine nozzles with different center offsets and different ratios of the bases of the trapezoidal outlet were generated based on curvature control regulation.Computational Fluid Dynamics(CFD)simulations have been conducted to obtain the flow field in the nozzle,and Forward-Backward Iterative Physical Optics(FBIPO)method was applied to study the electromagnetic scattering characteristics of the nozzle.Guarantee Convergence Particle Swarm Optimization(GCPSO)algorithm based on Radial Basis Function(RBF)neural network was used to optimize the geometry of the nozzle in consideration of its aerodynamic and electromagnetic scattering characteristics.The results show that the GCPSO method based on RBF can be used to optimize the aerodynamic characteristics of the internal flow and the scattering characteristics of the cavity of the serpentine nozzle with irregular outlet.The optimized model has a higher center offset and a lower ratio of the bases of the trapezoidal outlet after optimization compared to the original model.The optimized model leads to a slight change in aerodynamic performance,with a total pressure recovery coefficient increase of 0.31%and a discharge coefficient increase of 0.41%.In addition,the Radar Cross Section(RCS)decreases also by around 83.33%and the overall performance is significantly improved,with a decrease of the optimized objective function by around 38.74%.展开更多
With better understanding of the quality and physico-mechanical properties of rocks of dam foundation,and the physico-mechanical properties and structure design of arch dam in association with the foundation excavatio...With better understanding of the quality and physico-mechanical properties of rocks of dam foundation,and the physico-mechanical properties and structure design of arch dam in association with the foundation excavation of Xiluodu arch dam,the excavation optimization design was proposed for the foundation surface on the basis of feasibility study.Common analysis and numerical analysis results demonstrated the feasibility of using the weakly weathered rocks III1and III2as the foundation surface of super-high arch dam.In view of changes in the geological conditions at the dam foundation along the riverbed direction,the design of extending foundation surface excavation area and using consolidating grouting and optimizing structure of dam bottom was introduced,allowing for harmonization of the arch dam and foundation.Three-dimensional(3D)geomechanics model test and fi nite element analysis results indicated that the dam body and foundation have good overload stability and high bearing capacity.The monitoring data showed that the behaviors of dam and foundation correspond with the designed patterns in the construction period and the initial operation period.展开更多
Based on analyses of the theories of groundwater unsteady flow in deep well dewatering in the deep foundation pit, Theis equations are chosen to calculate and analyze the relationship between water level drawdown of c...Based on analyses of the theories of groundwater unsteady flow in deep well dewatering in the deep foundation pit, Theis equations are chosen to calculate and analyze the relationship between water level drawdown of confined aquifer and dewatering duration. In order to reduce engineering cost and diminish detrimental effect on ambient surrounding, optimization design target function based on the control of confined water drawdown and four restriction requisitions based on the control of safe water level, resistance to throwing up from the bottom of foundation pit, avoiding excessively great subsidence and unequal surface subsidence are proposed. A deep well dewatering project in the deep foundation pit is optimally designed. The calculated results including confined water level drawdown and surface subsidence are in close agreement with the measured results, and the optimization design can effectively control both surface subsidence outside foundation pit and unequal subsidence as a result of dewatering.展开更多
The current research of complex nonlinear system robust optimization mainly focuses on the features of design parameters, such as probability density functions, boundary conditions, etc. After parameters study, high-d...The current research of complex nonlinear system robust optimization mainly focuses on the features of design parameters, such as probability density functions, boundary conditions, etc. After parameters study, high-dimensional curve or robust control design is used to find an accurate robust solution. However, there may exist complex interaction between parameters and practical engineering system. With the increase of the number of parameters, it is getting hard to determine high-dimensional curves and robust control methods, thus it＇s difficult to get the robust design solutions. In this paper, a method of global sensitivity analysis based on divided variables in groups is proposed. By making relevant variables in one group and keeping each other independent among sets of variables, global sensitivity analysis is conducted in grouped variables and the importance of parameters is evaluated by calculating the contribution value of each parameter to the total variance of system response. By ranking the importance of input parameters, relatively important parameters are chosen to conduct robust design analysis of the system. By applying this method to the robust optimization design of a real complex nonlinear system-a vehicle occupant restraint system with multi-parameter, good solution is gained and the response variance of the objective function is reduced to 0.01, which indicates that the robustness of the occupant restraint system is improved in a great degree and the method is effective and valuable for the robust design of complex nonlinear system. This research proposes a new method which can be used to obtain solutions for complex nonlinear system robust design.展开更多
A new method is proposed for slope optimization design based on the limit curve method, where the slope is in the limit equilibrium state when the limit slope curve determined by the slip-line field theory and the slo...A new method is proposed for slope optimization design based on the limit curve method, where the slope is in the limit equilibrium state when the limit slope curve determined by the slip-line field theory and the slope intersect at the toe of the slope. Compared with the strength reduction (SR) method, finite element limit analysis method, and the SR method based on Davis algorithm, the new method is suitable for determining the slope stability and limit slope angle (LSA). The optimal slope shape is determined based on a series of slope heights and LSA values, which increases the LSA by 2.45°-11.14° and reduces an invalid overburden amount of rocks by 9.15%, compared with the space mechanics theory. The proposed method gives the objective quantification index of instability criterion, and results in a significant engineering economy.展开更多
In order to improve turbine internal efficiency and lower manufacturing cost, a new highly loaded rotating blade has been developed. The 3D optimization design method based on artificial neural network and genetic alg...In order to improve turbine internal efficiency and lower manufacturing cost, a new highly loaded rotating blade has been developed. The 3D optimization design method based on artificial neural network and genetic algorithm is adopted to construct the blade shape. The blade is stacked by the center of gravity in radial direction with five sections. For each blade section, independent suction and pressure sides are constructed from the camber line using Bezier curves. Three-dimensional flow analysis is carried out to verify the performance of the new blade. It is found that the new blade has improved the blade performance by 0.5%. Consequently, it is verified that the new blade is effective to improve the turbine internal efficiency and to lower the turbine weight and manufacturing cost by reducing the blade number by about 15%.展开更多
Pin and socket contacts are the key parts of electrical connector as aerospace electronic components. The contacts are also the direct carriers for signal transmitting of electronic equipments, passing the signal from...Pin and socket contacts are the key parts of electrical connector as aerospace electronic components. The contacts are also the direct carriers for signal transmitting of electronic equipments, passing the signal from the input end to the output end of electrical connector. The reliability of pin and socket contacts directly influences signal transmission. The goal of this study is to enhance the contact reliability of aerospace electrical connector. Computer simulation analysis was made on contacts performance data by utilizing the simulation system developed by PCL Language of MSC software. Furthermore, the results were experi- mentally validated so as to realize the objective of optimizing contacts design.展开更多
By analyzing a combined and spatial 6-bar linkage weft insertion mechanism, its practical model for optimization design is set up and the modification of penalty strategy is put forward so that the genetic algorithm c...By analyzing a combined and spatial 6-bar linkage weft insertion mechanism, its practical model for optimization design is set up and the modification of penalty strategy is put forward so that the genetic algorithm can be better used in optimization design for mechanisms with non- linear constraints. The design result is discussed.展开更多
In order to improve the safety of the battery of satellite side mounting,and prevent the screw from producing excess due to frequent assembly and disassembly,the YS-20 material replacement and structure optimization d...In order to improve the safety of the battery of satellite side mounting,and prevent the screw from producing excess due to frequent assembly and disassembly,the YS-20 material replacement and structure optimization design of the screw body are carried out under the premise of not changing the original tooling.The double⁃shear test of YS-20 bar is carried out,and the ANSYS optimization design module is used to design 7×7×6,a total of 294,calculation cases of D1,D2,T,the three important dimension parameters of screw structure.The actual bearing state of screw composite structure is accurately simulated by using asymmetric contact model.Three comprehensive evaluations are established,and the calculation examples satisfying the conditions are evaluated comprehensively.The final results are T=12.2 mm,D1=16 mm,D2=2 mm.The stress verification and contact analysis are carried out for the final scheme and the bearing state and contact state optimized screw structure are obtained.展开更多
基金the National Natural Science Foundation of China(21962008)Yunnan Province Excellent Youth Fund Project(202001AW070005)+1 种基金Candidate Talents Training Fund of Yunnan Province(2017PY269SQ,2018HB007)Yunnan Ten Thousand Talents Plan Young&Elite Talents Project(YNWR-QNBJ-2018-346).
文摘Electrochemical water splitting has long been considered an effective energy conversion technology for trans-ferring intermittent renewable electricity into hydrogen fuel,and the exploration of cost-effective and high-performance electrocatalysts is crucial in making electrolyzed water technology commercially viable.Cobalt phosphide(Co-P)has emerged as a catalyst of high potential owing to its high catalytic activity and durability in water splitting.This paper systematically reviews the latest advances in the development of Co-P-based materials for use in water splitting.The essential effects of P in enhancing the catalytic performance of the hydrogen evolution reaction and oxygen evolution reaction are first outlined.Then,versatile synthesis techniques for Co-P electrocatalysts are summarized,followed by advanced strategies to enhance the electrocatalytic performance of Co-P materials,including heteroatom doping,composite construction,integration with well-conductive sub-strates,and structure control from the viewpoint of experiment.Along with these optimization strategies,the understanding of the inherent mechanism of enhanced catalytic performance is also discussed.Finally,some existing challenges in the development of highly active and stable Co-P-based materials are clarified,and pro-spective directions for prompting the wide commercialization of water electrolysis technology are proposed.
基金the financial support from the National Natural Science Foundation of China(No.52325905)Key Technology Research Projects of Power China(No.DJ-HXGG-2023-04 and No.DJ-HXGG-2023-16).
文摘The demand for underground space and sustainable energy has driven the need for underground structures.Large underground caverns,being an underground structure carrier,offers a feasible solution.However,the stability analysis and optimization design of large underground caverns is always a great challenge due to the high geostress,complicated rock condition,and high sidewalls and large spans in size.By collecting and reviewing a large amount of relevant research literature from 1970 to 2023,the efforts on the advances in stability analysis methods and optimization design of large underground caverns are described,then the research trends in this field through keywords were found and typical deformation and break modes of large underground caverns with high geostress are summarized.The review reveals that stability analysis and optimization are the recent active research topics.There are seven typical deformation and break modes of large underground caverns under high geostress,four stability analysis methods and four theories of optimization design of large under-ground caverns.With the progress of science and technology and society,intelligent design,mechanized con-struction and greening construction are the development trend in this field.The research results can provide a constructive reference for the stability analysis and optimization design of large underground caverns under high geostress.
基金supported by the National Natural Science Foundation of China (623B2028).
文摘The advanced fin-shaped field-effect transistor(FinFET)technology offers higher integration density and stronger channel control capabilities,however,more complex process effects are also introduced which have significant influence on device performance.To address these issues,we complete a design-technology co-optimization(DTCO)focused on FinFET,including both process-induced effect during gate formation and corresponding digital unit optimization design.The 14 nm Fin-FET complementary metal oxide semiconductor(CMOS)technology is used to illustrate the sensitivity of transistor perfor-mance to process-induced effect,specifically the poly pitch effect(PPE)and cut poly effect(CPE).Predictive technology com-puter aided design(TCAD)simulations have been carried out to evaluate the transistor performance in advance.Based on the results,optimizations in digital unit design is proposed.Fall delay of the digital unit inverter is decreased by 0.7%,and the rise delay is decreased by 2.1%.For multiple selector(MUX2NV),the delay decreases by 4.64%for rise and 3.56%for drop,respec-tively.
基金the National Key Research and Development Program of China(Grant Number 2021YFB1714600)the National Natural Science Foundation of China(Grant Number 52075195)the Fundamental Research Funds for the Central Universities,China through Program No.2172019kfyXJJS078.
文摘With the continuous advancement in topology optimization and additive manufacturing(AM)technology,the capability to fabricate functionally graded materials and intricate cellular structures with spatially varying microstructures has grown significantly.However,a critical challenge is encountered in the design of these structures–the absence of robust interface connections between adjacent microstructures,potentially resulting in diminished efficiency or macroscopic failure.A Hybrid Level Set Method(HLSM)is proposed,specifically designed to enhance connectivity among non-uniform microstructures,contributing to the design of functionally graded cellular structures.The HLSM introduces a pioneering algorithm for effectively blending heterogeneous microstructure interfaces.Initially,an interpolation algorithm is presented to construct transition microstructures seamlessly connected on both sides.Subsequently,the algorithm enables the morphing of non-uniform unit cells to seamlessly adapt to interconnected adjacent microstructures.The method,seamlessly integrated into a multi-scale topology optimization framework using the level set method,exhibits its efficacy through numerical examples,showcasing its prowess in optimizing 2D and 3D functionally graded materials(FGM)and multi-scale topology optimization.In essence,the pressing issue of interface connections in complex structure design is not only addressed but also a robust methodology is introduced,substantiated by numerical evidence,advancing optimization capabilities in the realm of functionally graded materials and cellular structures.
文摘An optimization design was conducted for the shape of the pressure vessel with a thin-shell shell. During this process, the optimization calculation was performed with the aid of the genetic algorithm toolbox included in Matlab. Firstly, through the parametric modeling function of APDL, models such as arc-shaped, parabolic, elliptical, and those generated by the fitting curve command were successfully constructed. Meanwhile, the relevant settings of material properties were accomplished, and the static analysis was conducted. Secondly, the optimization calculation process was initiated using the genetic algorithm toolbox in Matlab. Eventually, through analysis and judgment, the model generated by the fitting curve command was relatively superior within the category of the best shape.
基金the National Natural Science Foundation of China(No.51975244)。
文摘For effectively improving the overall performance of fire truck frame structure,and solving the complexity of previous methods in the frame optimization design process,the traditional grey relational grade ranking needs to be improved.First,the first-order modal test was conducted to verify the validity of the initial frame model.Then,based on this model,a high-strength steel frame was designed to reduce deformation,maximum stress,and frame mass,and increase the fatigue life and the frequencies of the first bending modal and first torsional modal.Sixty groups of sample points were generated through Hammersley method.Subsequently,improved grey relational analysis with principal component analysis was proposed to realize the optimal design of the frame structure.Finally,the optimal combination of design parameters for the frame was obtained using the proposed method.Meanwhile,the optimized frame structure is found by comparing the models before and after optimization,and the mass is reduced by 14.8%.Moreover,the computational cost can be reduced by 135%when the proposed method is compared with the previous algorithm.Therefore,the proposed method can effectively improve the performance of the frame and improve the computational efficiency.
基金Supported by the National Natural Science Foundation of China (51675509)Wenzhou Public Welfare Industrial Technology Project (G20170026).
文摘In order to improve the performance and service life of the Leningrader seal of the Stirling engine piston rod,interference,pre-load and friction coefficient were taken as influencing factors,and the curved surface response method was adopted to reduce the contact stress of sealing surface and von Mises stress of the sealing sleeve as the response index,with the optimization goal of reducing wear and extending life.The above three key parameters are analyzed and optimized,the influence of each parameter on the sealing performance and service life is obtained,and the best combination scheme of the three is determined.The results show that the interaction between pre-tightening force and interference fit has the greatest impact on contact stress.The interaction between interference fit and friction coeffi-cient has the most significant effect on von Mises stress.The optimized parameters can reduce the maximum contact stress and maximum von Mises stress of the sealing sleeve by 26.3%and 20.6%,respectively,under a media pressure of 5-9 MPa.Test bench verification shows that the leakage of the optimized sealing device in 12 h is reduced by 0.44 cc·min^(-1)(1 cc=1 cm^(3)).The wear rate of the sealing sleeve is 1.08%before optimization and 0.45%after optimization,indicating that the optimized parameters in this paper are effective.
文摘Aiming at the problems in current cam profile optimization processes, such as simple dynamics models, limited geometric accuracy and low design automatization level, a new dynamic optimization mode is put forward. Based on the parameterization modeling technique of MSC. ADAMS platform, the different steps in current mode are reorganized, thus obtaining an upgraded mode called the ＂parameterized-prototype-based cam profile dynamic optimization mode＂. A parameterized prototype（PP） of valve mechanism is constructed in the course of dynamic optimization for cam profiles. Practically, by utilizing PP and considering the flexibility of the parts in valve mechanism, geometric accuracy and design automatization are improved.
文摘The well number and the cavity length of 1.55μm wavelength In 1-x-y Ga y Al x As MQW DFB lasers are optimized using a simple model.A low threshold,maximum operating temperature of 550～560K,and high relaxation oscillation frequency of over 30GHz MQW DFB laser is presented.
基金This project is supported by Provincial ScienceTechnology Foundation of Liaoning (No. 20022132)
文摘Optimization design of hydraulic manifold blocks (HMB) is studied as acomplex solid spatial layout problem. Based on comprehensive research into structure features anddesign rules of HMB, an optimal mathematical model for this problem is presented. Usinghuman-computer cooperative genetic algorithm (GA) and its hybrid optitation strategies, integratedlayout and connection design schemes of HMB can be automatically optimized. An example is given totestify it.
基金supported by the National Key Project of China(No.GJXM92579)the National Natural Science Foundation of China(Nos.92052203 and 11872230 and 91852108)。
文摘Natural ice accretion on the lifting surface of an aircraft is detrimental to its aerodynamic performance, as it changes the effective streamlined body. The main focus of this work considers the optimization design of airfoils under atmospheric icing conditions for the Unmanned Aerial Vehicle(UAV). The ice formation process is simulated by the Eulerian approach and the three-dimensional Myers model. A three-equation turbulence model is implemented to accurately predict the stall performance of the iced airfoil. In recognition of the real atmospheric variability in the icing parameters, the medium volume diameter of supercooled water droplets is treated as an uncertainty with an assumed probability density function. A technique of polynomial chaos expansion is used to propagate the input uncertainty through the deterministic system. The numerical results show that the multipoint/multiobjective optimization strategy can efficiently improve both the ice tolerance and the cruise performance of an airfoil. The reason for the focus on robust optimization is that the ice angle of the optimized airfoil becomes less critical to the incoming flow.The optimized airfoils are applied to a UAV platform, in which the performance improvement and the relevant key flow feature are both preserved.
基金the financial support of the Fundamental Research Funds for the Central Universities(No.31020190MS708)。
文摘Comprehensive optimization design of serpentine nozzle with trapezoidal outlet was studied to improve its aerodynamic and electromagnetic scattering performance.Serpentine nozzles with different center offsets and different ratios of the bases of the trapezoidal outlet were generated based on curvature control regulation.Computational Fluid Dynamics(CFD)simulations have been conducted to obtain the flow field in the nozzle,and Forward-Backward Iterative Physical Optics(FBIPO)method was applied to study the electromagnetic scattering characteristics of the nozzle.Guarantee Convergence Particle Swarm Optimization(GCPSO)algorithm based on Radial Basis Function(RBF)neural network was used to optimize the geometry of the nozzle in consideration of its aerodynamic and electromagnetic scattering characteristics.The results show that the GCPSO method based on RBF can be used to optimize the aerodynamic characteristics of the internal flow and the scattering characteristics of the cavity of the serpentine nozzle with irregular outlet.The optimized model has a higher center offset and a lower ratio of the bases of the trapezoidal outlet after optimization compared to the original model.The optimized model leads to a slight change in aerodynamic performance,with a total pressure recovery coefficient increase of 0.31%and a discharge coefficient increase of 0.41%.In addition,the Radar Cross Section(RCS)decreases also by around 83.33%and the overall performance is significantly improved,with a decrease of the optimized objective function by around 38.74%.
文摘With better understanding of the quality and physico-mechanical properties of rocks of dam foundation,and the physico-mechanical properties and structure design of arch dam in association with the foundation excavation of Xiluodu arch dam,the excavation optimization design was proposed for the foundation surface on the basis of feasibility study.Common analysis and numerical analysis results demonstrated the feasibility of using the weakly weathered rocks III1and III2as the foundation surface of super-high arch dam.In view of changes in the geological conditions at the dam foundation along the riverbed direction,the design of extending foundation surface excavation area and using consolidating grouting and optimizing structure of dam bottom was introduced,allowing for harmonization of the arch dam and foundation.Three-dimensional(3D)geomechanics model test and fi nite element analysis results indicated that the dam body and foundation have good overload stability and high bearing capacity.The monitoring data showed that the behaviors of dam and foundation correspond with the designed patterns in the construction period and the initial operation period.
基金This paper is supported by the Hubei Construct Science Foundation of China (G200013).
文摘Based on analyses of the theories of groundwater unsteady flow in deep well dewatering in the deep foundation pit, Theis equations are chosen to calculate and analyze the relationship between water level drawdown of confined aquifer and dewatering duration. In order to reduce engineering cost and diminish detrimental effect on ambient surrounding, optimization design target function based on the control of confined water drawdown and four restriction requisitions based on the control of safe water level, resistance to throwing up from the bottom of foundation pit, avoiding excessively great subsidence and unequal surface subsidence are proposed. A deep well dewatering project in the deep foundation pit is optimally designed. The calculated results including confined water level drawdown and surface subsidence are in close agreement with the measured results, and the optimization design can effectively control both surface subsidence outside foundation pit and unequal subsidence as a result of dewatering.
基金Supported by National Natural Science Foundation of China(Grant No.51275164)
文摘The current research of complex nonlinear system robust optimization mainly focuses on the features of design parameters, such as probability density functions, boundary conditions, etc. After parameters study, high-dimensional curve or robust control design is used to find an accurate robust solution. However, there may exist complex interaction between parameters and practical engineering system. With the increase of the number of parameters, it is getting hard to determine high-dimensional curves and robust control methods, thus it＇s difficult to get the robust design solutions. In this paper, a method of global sensitivity analysis based on divided variables in groups is proposed. By making relevant variables in one group and keeping each other independent among sets of variables, global sensitivity analysis is conducted in grouped variables and the importance of parameters is evaluated by calculating the contribution value of each parameter to the total variance of system response. By ranking the importance of input parameters, relatively important parameters are chosen to conduct robust design analysis of the system. By applying this method to the robust optimization design of a real complex nonlinear system-a vehicle occupant restraint system with multi-parameter, good solution is gained and the response variance of the objective function is reduced to 0.01, which indicates that the robustness of the occupant restraint system is improved in a great degree and the method is effective and valuable for the robust design of complex nonlinear system. This research proposes a new method which can be used to obtain solutions for complex nonlinear system robust design.
基金Project(JJKH20180450KJ)supported by Education Department of Jilin Province,ChinaProject(20166008)supported by the Science and Technology Bureau of Jilin Province,China
文摘A new method is proposed for slope optimization design based on the limit curve method, where the slope is in the limit equilibrium state when the limit slope curve determined by the slip-line field theory and the slope intersect at the toe of the slope. Compared with the strength reduction (SR) method, finite element limit analysis method, and the SR method based on Davis algorithm, the new method is suitable for determining the slope stability and limit slope angle (LSA). The optimal slope shape is determined based on a series of slope heights and LSA values, which increases the LSA by 2.45°-11.14° and reduces an invalid overburden amount of rocks by 9.15%, compared with the space mechanics theory. The proposed method gives the objective quantification index of instability criterion, and results in a significant engineering economy.
文摘In order to improve turbine internal efficiency and lower manufacturing cost, a new highly loaded rotating blade has been developed. The 3D optimization design method based on artificial neural network and genetic algorithm is adopted to construct the blade shape. The blade is stacked by the center of gravity in radial direction with five sections. For each blade section, independent suction and pressure sides are constructed from the camber line using Bezier curves. Three-dimensional flow analysis is carried out to verify the performance of the new blade. It is found that the new blade has improved the blade performance by 0.5%. Consequently, it is verified that the new blade is effective to improve the turbine internal efficiency and to lower the turbine weight and manufacturing cost by reducing the blade number by about 15%.
文摘Pin and socket contacts are the key parts of electrical connector as aerospace electronic components. The contacts are also the direct carriers for signal transmitting of electronic equipments, passing the signal from the input end to the output end of electrical connector. The reliability of pin and socket contacts directly influences signal transmission. The goal of this study is to enhance the contact reliability of aerospace electrical connector. Computer simulation analysis was made on contacts performance data by utilizing the simulation system developed by PCL Language of MSC software. Furthermore, the results were experi- mentally validated so as to realize the objective of optimizing contacts design.
文摘By analyzing a combined and spatial 6-bar linkage weft insertion mechanism, its practical model for optimization design is set up and the modification of penalty strategy is put forward so that the genetic algorithm can be better used in optimization design for mechanisms with non- linear constraints. The design result is discussed.
文摘In order to improve the safety of the battery of satellite side mounting,and prevent the screw from producing excess due to frequent assembly and disassembly,the YS-20 material replacement and structure optimization design of the screw body are carried out under the premise of not changing the original tooling.The double⁃shear test of YS-20 bar is carried out,and the ANSYS optimization design module is used to design 7×7×6,a total of 294,calculation cases of D1,D2,T,the three important dimension parameters of screw structure.The actual bearing state of screw composite structure is accurately simulated by using asymmetric contact model.Three comprehensive evaluations are established,and the calculation examples satisfying the conditions are evaluated comprehensively.The final results are T=12.2 mm,D1=16 mm,D2=2 mm.The stress verification and contact analysis are carried out for the final scheme and the bearing state and contact state optimized screw structure are obtained.
