Because of the complexities of fluid dynamics equations and the structure of heat exchangers, few theoretical solutions have been acquired to specify the shell side characteristics of the rod baffle heat exchanger （R...Because of the complexities of fluid dynamics equations and the structure of heat exchangers, few theoretical solutions have been acquired to specify the shell side characteristics of the rod baffle heat exchanger （RBHE）. Based on the platform of PHEONICS version 3.5.1, a three-dimensional numerical method for predicting the turbulent fluid flow behavior in the shell side of the rod baffle heat exchangers is developed in this paper. With this method, modeling of the tube bundle is carried out based on the porous media concept using volumetric porosities and applicable flow resistance correlations. Turbulence effects are modeled using a standard κ-ε model. It is shown that the simulation results and experimental results are in good agreement in the shell side. The maximum absolute deviation value of pressure drops is less than 5%, and that of the heat transfer coefficients is less than 8%. Furthermore, the numerical model is used to optimize the structure of the RBHE and improves its performance.展开更多
The physical and mathematical model of an operating electrowinning cell was established, and the flow of electrolyte was numerically simulated by the commercial software Fluent. The results indicate that there are two...The physical and mathematical model of an operating electrowinning cell was established, and the flow of electrolyte was numerically simulated by the commercial software Fluent. The results indicate that there are two circulations at the surface flow where part of electrolyte backflows to the inlet from the side of cell, and the rest flows directly to the outlet, and the separation of two circulations with opposite direction occurs at the 20th pair of anode-cathode. This phenomenon was observed in the real operation. The electrolyte flows into the space between anode and cathode from the side portion of the cell. Meanwhile, the interelectrode effective flow rate （IEFR） is put forward to describe quantitively the flow field characteristics and is defined as the ratio of electrolyte flow between the anode and cathode to the total flow area. The influences of structure parameters and operating conditions on IEFR, such as the inlet angle, the volumetric flow rate, the inlet position and the height of steel baffles were simulated. The inlet position has a significant influence on the IEFR and its optimal value is 0.9 m below free surface. The inlet angle should be in the range from -10° to 10°. IEFR is in linear proportion with the volumetric flow rate, and the height of the steel baffle has little influence on the flow field.展开更多
Porthole die extrusion method is used to produce hollow aluminum profile. Due to the complexity of the porthole die structure and the material flow, it is very difficult to get ideal profile products with the firstly ...Porthole die extrusion method is used to produce hollow aluminum profile. Due to the complexity of the porthole die structure and the material flow, it is very difficult to get ideal profile products with the firstly designed die structure. Finite volume numerical simulation was used to analyze the extrusion process of a hollow profile with porthole die and the problem of non-uniform material flow was found. Optimization was made to the originally designed die to solve the problem. Lower load, reasonable seaming location and even extruded forepart with uniform material flow in the optimized die extrusion were obtained. Guidelines to porthole die design were given and it is also concluded that finite volume method with Eulerian description avoids mesh regeneration and is suitable to numerical simulation of severe deformation processes, such as profile extrusion.展开更多
To eliminate the shrinkage porosity in low pressure casting of an A356 aluminum alloy intake manifold casting, numerical simulation on fi lling and solidifi cation processes of the casting was carried out using the Pr...To eliminate the shrinkage porosity in low pressure casting of an A356 aluminum alloy intake manifold casting, numerical simulation on fi lling and solidifi cation processes of the casting was carried out using the ProCAST software. The gating system of the casting is optimized according to the simulation results. Results show that when the gating system consists of only one sprue, the fi lling of the molten metal is not stable; and the casting does not follow the sequence solidifi cation, and many shrinkage porosities are observed through the casting. After the gating system is improved by adding one runner and two in-gates, the fi lling time is prolonged from 4.0 s to 4.5 s, the fi lling of molten metal becomes stable, but this casting does not follow the sequence solidifi cation either. Some shrinkage porosity is also observed in the hot spots of the casting. When the gating system was further improved by adding risers and chill to the hot spots of the casting, the shrinkage porosity defects were eliminated completely. Finally, by using the optimized gating system the A356 aluminum alloy intake manifold casting with integrated shape and smooth surface as well as dense microstructure was successfully produced.展开更多
High pressure die casting(HPDC) is a kind of near net shape manufacturing method. However, air entrapment in HPDC parts has serious effects upon the casting quality. In order to reduce the air entrapment defects in a ...High pressure die casting(HPDC) is a kind of near net shape manufacturing method. However, air entrapment in HPDC parts has serious effects upon the casting quality. In order to reduce the air entrapment defects in a AlSi10 MnMg alloy thin-wall longitudinal load-bearing beam produced by HPDC, different gating systems were designed and simulated by software Flow-3D to evaluate the entrapped air. Simulation results showed that when the beam is produced by the original designed gating system with a middle ingate, there exist obvious air entrapments in the critical area; the volume of air entrapment was reduced by replacing the middle ingate to an overflow well, and the filling of molten metal became more stable. When the middle ingate was removed for further improvement, the volume of air entrapment was decreased drastically. The parts with glossy surface and good microstructure have been successfully produced by using the final optimized gating system based on simulation results.展开更多
Shrinkage defects can be formed easily at critical location during low pressure die casting (LPDC) of aluminum alloy cylinder body. It has harmful effect on the products. Mold filling and solidification process of a c...Shrinkage defects can be formed easily at critical location during low pressure die casting (LPDC) of aluminum alloy cylinder body. It has harmful effect on the products. Mold filling and solidification process of a cylinder body was simulated by using of Z-CAST software. The casting method was improved based on the simulation results. In order to create effective feeding passage, the structure of casting was modified by changing the location of strengthening ribs at the bottom, without causing any adverse effect on the part's performance. Inserting copper billet at suitable location of the die is a valid way to create suitable solidification sequence that is beneficial to the feeding. Using these methods, the shrinkage defect was completely eliminated at the critical location.展开更多
3-Dvelocity and temperature fields of mold filling and solidification processes of large-sized castingswere calculated,and the efficiency and accuracy of numerical calculation were studied.The mold filling andsolidifi...3-Dvelocity and temperature fields of mold filling and solidification processes of large-sized castingswere calculated,and the efficiency and accuracy of numerical calculation were studied.The mold filling andsolidification processes of large-sized stainless steel,iron and aluminum alloy castings were simulated by using ofnew scheme;their casting processes were optimized,and then applied to produce castings.展开更多
In order to acquire the flow pattern and investigate the settling behavior of the red mud in the separation thickener,computational fluid dynamics(CFD),custom subroutines and agglomerates settling theory were employed...In order to acquire the flow pattern and investigate the settling behavior of the red mud in the separation thickener,computational fluid dynamics(CFD),custom subroutines and agglomerates settling theory were employed to simulate the three-dimensional flow field in an industrial scale thickener with the introduction of a self-dilute feed system.The simulation results show good agreement with the measurement onsite and the flow patterns of the thickener are presented and discussed on both velocity and concentration field.Optimization experiments on feed well and self-dilute system were also carried out,and indicate that the optimal thickener system can dilute the solid concentration in feed well from 110 g/L to 86 g/L which would help the agglomerates' formation and improve the red mud settling speed.Furthermore,the additional power of recirculation pump can be saved and flocculants dosage was reduced from 105g/t to 85g/t in the operation.展开更多
The Xiangshan deposit in Jiangxi province is one of the most important uranium deposits in China. The aim of this study is to achieve a better understanding of mineralization in the Xiangshan deposit through numerical...The Xiangshan deposit in Jiangxi province is one of the most important uranium deposits in China. The aim of this study is to achieve a better understanding of mineralization in the Xiangshan deposit through numerical simulation. In order to find the most favorable locations of mineralization and to help further mineral exploration, a coupling deforma- tion and fluid flow model has been established to describe the mineralization process. In this model, the simulation re- constructs the strata deformations under fields of compressive stress and thrust structure on the hanging wall of the Zou-Shi fault. Compared with practical information, the simulation results are consistent with the No. 51 exploration section of the western Xiangshan. In addition, on the basis of geological information provided by previous investigators, the model simulates the flow process of fluids under compressive stress fields. The result suggests that many tensional areas are formed, which can help the fluid flowing upward from deeper parts. The fluid is easy to concentrate on the breccia fractured zone between two volcanic layers, especially on the intersection parts with faults, resulting in the for- mation of favourable locations of mineralization. In addition, the model is significant in guiding the exploration of ura- nium deposits in the western Xiangshan and provides clues for further exploration of deposits.展开更多
The kill characteristics of aimed warhead were studied. Emphasis on the improvement of initiation system, experiments and three dimensional numerical investigations were carried out. Simulation results of side three i...The kill characteristics of aimed warhead were studied. Emphasis on the improvement of initiation system, experiments and three dimensional numerical investigations were carried out. Simulation results of side three initiation points fit experiments well. Optimal initiation style is obtained through further simulation. It shows that the effective fragments and the effective kill energy of the optimal scheme increase 12.8% and 10.1% respectively.展开更多
Although the shell mould casting process has a wide range of application in many fields,the prediction of casting defects is still a problem.In the present work,a typical leaf spring bracket casting of ZG310-570 was f...Although the shell mould casting process has a wide range of application in many fields,the prediction of casting defects is still a problem.In the present work,a typical leaf spring bracket casting of ZG310-570 was fabricated by shell mold casting.The finite element model and ProCAST software were utilized for simulating the filling and solidification processes of the casting;and the formation mechanism of the gas pore,and shrinkage porosity defects were analyzed.The results indicate that the gas pore and shrinkage porosity defects are formed due to air entrapment,insufficient feeding and non-sequential solidification.Subsequently,through changing the position of risers,adding a connecting channel between the risers,and setting blind risers at the U-shaped brackets,an optimized gating and feeding system was established to improve the quality of the casting.After optimization,the gas pore and shrinkage porosity defects of the leaf spring bracket casting are effectively eliminated.The experiment results with the optimized casting process are in good agreement with the numerical simulation,which verifies the validity of the finite element model in the shell mould casting.展开更多
The tool with polygonal pin profile has been widely employed in friction stir welding(FSW) of aluminum, but there is hardly an effective optimization methodology existed as the thermomechanical characteristics affecte...The tool with polygonal pin profile has been widely employed in friction stir welding(FSW) of aluminum, but there is hardly an effective optimization methodology existed as the thermomechanical characteristics affected by pins with various flats number have not been understood comprehensively. Therefore, the present work employs a 3-dimensional computational fluid dynamics(CFD) model to have an integrated observation of the FSW process with the effect of polygonal pin profiles. Both the heat generation modes due to contact friction at the tool–workpiece interface and volumetric viscous dissipation in the vicinity of the tool are considered. The model is utilized to give a quantitative analysis of the heat generation, temperature distribution, plastic material flow and welding loads during the FSW process for various tools with polygonal pin profiles, as well as a variety of shoulder diameters, welding speeds and tool rotation speeds. The calculated results of thermal cycles, tool torques and joint cross sections for some typical polygonal pins and welding parameters are all found to be compared well with the experimental ones, which demonstrates the feasibility and applicability of the present numerical model. Particularly, a methodology is developed for the optimization of the flats number by identifying the torque components in both parallel and vertical direction of the pin-side flat region. The results show that the optimized pin flats number increases with increasing tool rotation speed, while the influence of both welding speed and shoulder diameter can be supposed to be insignificant. Moreover, the dependability of the optimized results is also discussed by considering wear tendency and service life of the pin for multiple welding conditions.展开更多
Substrate, a typical ultra-slender aluminum alloy structural components with a large aspect ratio and complex internal structure, was traditionally manufactured by re-assembly and sub-welding. In order to realize the ...Substrate, a typical ultra-slender aluminum alloy structural components with a large aspect ratio and complex internal structure, was traditionally manufactured by re-assembly and sub-welding. In order to realize the monoblock casting of the substrate, the Pro/E software was utilized to carry out three-dimensional(3D) modeling of the substrate casting, and the filling and solidification processes were calculated, as well as the location and types of casting defects were predicted by the casting simulation software Anycasting. Results of the filling process simulation show that the metal liquid is distributed into each gap runner evenly and smoothly. There is no serious vortex phenomenon in the mold cavity, and the trajectory of the virtual particles is clear. Results of the solidification process simulation show that shrinkage cavities mainly appear at the junction of gap runners and the rail surface of the substrate. The average deformation is 0.6 mm in X direction, 3.8 mm in Y direction, and 8.2 mm in Z direction. Based on the simulation results, the casting process of the substrate was optimized, and qualified castings were successfully produced, which will provide a reference for the casting process design of other ultraslender aluminum alloy structural components.展开更多
According to the innate characteristic of four types of furnace, the copper flash continuous smelting （CFCS） furnace can be considered a synthetic reactor of two relatively independent processes： flash matte smelti...According to the innate characteristic of four types of furnace, the copper flash continuous smelting （CFCS） furnace can be considered a synthetic reactor of two relatively independent processes： flash matte smelting process （FMSP） and copper continuous converting process （CCCP）. Then, the CFCS thermodynamic model was proposed by establishing the multi-phase equilibrium model of FMSP and the local-equilibrium model of CCCP, respectively, and by combining them through the smelting intermediates. Subsequently, the influences of the furnace structures were investigated using the model on the formation of blister copper, the Fe3O4 behavior, the copper loss in slag and the copper recovery rate. The results show that the type D furnace, with double flues and a slag partition wall, is an ideal CFCS reactor compared with the other three types furnaces. For CFCS, it is effective to design a partition wall in the furnace to make FMSP and CCCP perform in two relatively independent zones, respectively, and to make smelting gas and converting gas discharge from respective flues.展开更多
Plastic injection molding is a very complex process and its process planning has a direct influence on product quality and production efficiency. This paper studied the optimization of injection molding process by com...Plastic injection molding is a very complex process and its process planning has a direct influence on product quality and production efficiency. This paper studied the optimization of injection molding process by combining the numerical simulation with back-propagation(BP) networks. The BP networks are trained by the results of numerical simulation. The trained BP networks may:(1) shorten time for process planning;(2) optimize process parameters;(3) be employed in on-line quality control;(4) be integrated with knowledge-based system(KBS) and case-based reasoning(CBR) to make intelligent process planning of injection molding.展开更多
Circulating fluidized bed flue gas desulfurization(CFB-FGD) process has been widely applied in recent years. However, high cost caused by the use of high-quality slaked lime and difficult operation due to the complex ...Circulating fluidized bed flue gas desulfurization(CFB-FGD) process has been widely applied in recent years. However, high cost caused by the use of high-quality slaked lime and difficult operation due to the complex flow field are two issues which have received great attention. Accordingly, a laboratory-scale fluidized bed reactor was constructed to investigate the effects of physical properties and external conditions on desulfurization performance of slaked lime, and the conclusions were tried out in an industrial-scale CFB-FGD tower. After that, a numerical model of the tower was established based on computational particle fluid dynamics(CPFD) and two-film theory. After comparison and validation with actual operation data, the effects of operating parameters on gas-solid distribution and desulfurization characteristics were investigated. The results of experiments and industrial trials showed that the use of slaked lime with a calcium hydroxide content of approximately 80% and particle size greater than 40 μm could significantly reduce the cost of desulfurizer. Simulation results showed that the flow field in the desulfurization tower was skewed under the influence of circulating ash. We obtained optimal operating conditions of 7.5 kg·s^(-1)for the atomized water flow, 70 kg·s^(-1)for circulating ash flow, and 0.56 kg·s^(-1)for slaked lime flow, with desulfurization efficiency reaching 98.19% and the exit flue gas meeting the ultraclean emission and safety requirements. All parameters selected in the simulation were based on engineering examples and had certain application reference significance.展开更多
Live bone inherently responds to applied mechanical stimulus by altering its internal tissue composition and ultimately biomechanical properties, structure and function. The final formation may structurally appear inf...Live bone inherently responds to applied mechanical stimulus by altering its internal tissue composition and ultimately biomechanical properties, structure and function. The final formation may structurally appear inferior by design but complete by function. To understand the loading response, this paper numerically investigated structural remodeling of mature sheep femur using evolutionary structural optimization method (ESO). Femur images from Computed Tomography scanner were used to determine the elastic modulus variation and subsequently construct finite element model of the femur with stiffest elasticity measured. Major muscle forces on dominant phases of healthy sheep gait were imposed on the femur under static mode. ESO was applied to progressively alter the remodeling of numerically simulated femur from its initial to final design by iteratively removing elements with low strain energy density (SED). The computations were repeated with two different mesh sizes to test the convergence. The elements within the medullary canal had low SEDs and therefore were removed during the optimization. The SEDs in the remaining elements varied with angle around the circumference of the shaft. Those elements with low SED were inefficient in supporting the load and thus fundamentally explained how bone remodels itself with less stiff inferior tissue to meet load demand. This was in line with the Wolff’s law of transformation of bone. Tissue growth and remodeling process was found to shape the sheep femur to a mechanically optimized structure and this was initiated by SED in macro-scale according to traditional principle of Wolff’s law.展开更多
Based on the study about the geological background of Beiya Gold Deposit, numerical simulation was conducted about the three-dimensional structural stress field for Beiya Gold Deposit by applying finite element theory...Based on the study about the geological background of Beiya Gold Deposit, numerical simulation was conducted about the three-dimensional structural stress field for Beiya Gold Deposit by applying finite element theory and by employing a linear elasticity model. Results of the simulation indicate that the Beiya syncline is a faulted basin, and a hidden fracture occurs in the west wing of the syncline.Under the action of the EW-trending compressive force, four nearly NS-trending fractures (groups) were generated in the stress stretching areas of the two wings of the syncline, and these fractures constitute favorable tectonic positions for the upward intrusion of porphyry magma and the occurrence of Au-Pb-Zn polymetallic deposits.展开更多
In this paper we use the finite element analysis software ANSYS10.0 to establish a finite element model for pressure gauge C -spring tube, and the main factors affected the relation between the pressure and distortion...In this paper we use the finite element analysis software ANSYS10.0 to establish a finite element model for pressure gauge C -spring tube, and the main factors affected the relation between the pressure and distortion displacement are analyzed. The results show that with the increasing of the spring tube wall thickness T and the minor axis length B, the elastic rigidity of spring tube increases, which is reduced with spring tube diameter D. Moreover, the major axis length H increases. Meanwhile, a pressure gauge spring tube has been optimized according to the simulation results bused on a model with special features, and the design results achieve the intended purpose. The analysis results provide a reliable method for the research and design of similar elastic elements.展开更多
The quality of skeleton system for the cheetah robot goes hand in hand with its bionic result of its shape, structure and functions. In view of the skeleton system constitution and structural characteristic of the che...The quality of skeleton system for the cheetah robot goes hand in hand with its bionic result of its shape, structure and functions. In view of the skeleton system constitution and structural characteristic of the cheetah, the team applied structure design, stimulation analysis and parameter optimization to developing the cheetah robot. In addition, after the invention of cheetah robot＇s anterior lumbar vertebra based on its functional attribute and connectivity attribute, the Solidworks Simulation was utilized to analyze the design, according to which improvement on the lumbar vertebra was made. Plus, the advantages of the CAD and CAE made the high efficiency of design work and high quality of the cheetah robot possible.展开更多
基金supported by the Scientific Research Project of Shanghai Municipal Education Commission (Grant No.06AZ018)
文摘Because of the complexities of fluid dynamics equations and the structure of heat exchangers, few theoretical solutions have been acquired to specify the shell side characteristics of the rod baffle heat exchanger （RBHE）. Based on the platform of PHEONICS version 3.5.1, a three-dimensional numerical method for predicting the turbulent fluid flow behavior in the shell side of the rod baffle heat exchangers is developed in this paper. With this method, modeling of the tube bundle is carried out based on the porous media concept using volumetric porosities and applicable flow resistance correlations. Turbulence effects are modeled using a standard κ-ε model. It is shown that the simulation results and experimental results are in good agreement in the shell side. The maximum absolute deviation value of pressure drops is less than 5%, and that of the heat transfer coefficients is less than 8%. Furthermore, the numerical model is used to optimize the structure of the RBHE and improves its performance.
基金Project(2011AA061003)supported by the National High-Tech Research and Development Program of China
文摘The physical and mathematical model of an operating electrowinning cell was established, and the flow of electrolyte was numerically simulated by the commercial software Fluent. The results indicate that there are two circulations at the surface flow where part of electrolyte backflows to the inlet from the side of cell, and the rest flows directly to the outlet, and the separation of two circulations with opposite direction occurs at the 20th pair of anode-cathode. This phenomenon was observed in the real operation. The electrolyte flows into the space between anode and cathode from the side portion of the cell. Meanwhile, the interelectrode effective flow rate （IEFR） is put forward to describe quantitively the flow field characteristics and is defined as the ratio of electrolyte flow between the anode and cathode to the total flow area. The influences of structure parameters and operating conditions on IEFR, such as the inlet angle, the volumetric flow rate, the inlet position and the height of steel baffles were simulated. The inlet position has a significant influence on the IEFR and its optimal value is 0.9 m below free surface. The inlet angle should be in the range from -10° to 10°. IEFR is in linear proportion with the volumetric flow rate, and the height of the steel baffle has little influence on the flow field.
基金Project(50425517) supported by National Science Foundation for Distinguished Young Scholars of ChinaProject(50375087) supported by the Natural Science Foundation of ChinaProject(Q2004f01) supported by Natural Science Foundation of Shandong Province, China
文摘Porthole die extrusion method is used to produce hollow aluminum profile. Due to the complexity of the porthole die structure and the material flow, it is very difficult to get ideal profile products with the firstly designed die structure. Finite volume numerical simulation was used to analyze the extrusion process of a hollow profile with porthole die and the problem of non-uniform material flow was found. Optimization was made to the originally designed die to solve the problem. Lower load, reasonable seaming location and even extruded forepart with uniform material flow in the optimized die extrusion were obtained. Guidelines to porthole die design were given and it is also concluded that finite volume method with Eulerian description avoids mesh regeneration and is suitable to numerical simulation of severe deformation processes, such as profile extrusion.
基金supported by the National Natural Science Foundation of China(No.51204124)the China Postdoctoral Science Foundation(No.2012M511610)the Scientific Research Foundation of Wuhan Institute of Technology(No.14125041)
文摘To eliminate the shrinkage porosity in low pressure casting of an A356 aluminum alloy intake manifold casting, numerical simulation on fi lling and solidifi cation processes of the casting was carried out using the ProCAST software. The gating system of the casting is optimized according to the simulation results. Results show that when the gating system consists of only one sprue, the fi lling of the molten metal is not stable; and the casting does not follow the sequence solidifi cation, and many shrinkage porosities are observed through the casting. After the gating system is improved by adding one runner and two in-gates, the fi lling time is prolonged from 4.0 s to 4.5 s, the fi lling of molten metal becomes stable, but this casting does not follow the sequence solidifi cation either. Some shrinkage porosity is also observed in the hot spots of the casting. When the gating system was further improved by adding risers and chill to the hot spots of the casting, the shrinkage porosity defects were eliminated completely. Finally, by using the optimized gating system the A356 aluminum alloy intake manifold casting with integrated shape and smooth surface as well as dense microstructure was successfully produced.
基金supported by the Major Project of NSFC(51690161)the Student Innovation Program Major Project of Northeastern University(ZD1708)
文摘High pressure die casting(HPDC) is a kind of near net shape manufacturing method. However, air entrapment in HPDC parts has serious effects upon the casting quality. In order to reduce the air entrapment defects in a AlSi10 MnMg alloy thin-wall longitudinal load-bearing beam produced by HPDC, different gating systems were designed and simulated by software Flow-3D to evaluate the entrapped air. Simulation results showed that when the beam is produced by the original designed gating system with a middle ingate, there exist obvious air entrapments in the critical area; the volume of air entrapment was reduced by replacing the middle ingate to an overflow well, and the filling of molten metal became more stable. When the middle ingate was removed for further improvement, the volume of air entrapment was decreased drastically. The parts with glossy surface and good microstructure have been successfully produced by using the final optimized gating system based on simulation results.
基金the Innovation Fund for Outstanding Scholar of Henan Province (No.0621000700)
文摘Shrinkage defects can be formed easily at critical location during low pressure die casting (LPDC) of aluminum alloy cylinder body. It has harmful effect on the products. Mold filling and solidification process of a cylinder body was simulated by using of Z-CAST software. The casting method was improved based on the simulation results. In order to create effective feeding passage, the structure of casting was modified by changing the location of strengthening ribs at the bottom, without causing any adverse effect on the part's performance. Inserting copper billet at suitable location of the die is a valid way to create suitable solidification sequence that is beneficial to the feeding. Using these methods, the shrinkage defect was completely eliminated at the critical location.
文摘3-Dvelocity and temperature fields of mold filling and solidification processes of large-sized castingswere calculated,and the efficiency and accuracy of numerical calculation were studied.The mold filling andsolidification processes of large-sized stainless steel,iron and aluminum alloy castings were simulated by using ofnew scheme;their casting processes were optimized,and then applied to produce castings.
基金Project(50876116)supported by the National Natural Science Foundation of China
文摘In order to acquire the flow pattern and investigate the settling behavior of the red mud in the separation thickener,computational fluid dynamics(CFD),custom subroutines and agglomerates settling theory were employed to simulate the three-dimensional flow field in an industrial scale thickener with the introduction of a self-dilute feed system.The simulation results show good agreement with the measurement onsite and the flow patterns of the thickener are presented and discussed on both velocity and concentration field.Optimization experiments on feed well and self-dilute system were also carried out,and indicate that the optimal thickener system can dilute the solid concentration in feed well from 110 g/L to 86 g/L which would help the agglomerates' formation and improve the red mud settling speed.Furthermore,the additional power of recirculation pump can be saved and flocculants dosage was reduced from 105g/t to 85g/t in the operation.
基金Projects GPMR0547 supported by the State Key Laboratory of Geological Processes and Mineral Resources, China University of Geosciences, and 2002 CB 412601 by the Chinese Ministry of Science and Technology
文摘The Xiangshan deposit in Jiangxi province is one of the most important uranium deposits in China. The aim of this study is to achieve a better understanding of mineralization in the Xiangshan deposit through numerical simulation. In order to find the most favorable locations of mineralization and to help further mineral exploration, a coupling deforma- tion and fluid flow model has been established to describe the mineralization process. In this model, the simulation re- constructs the strata deformations under fields of compressive stress and thrust structure on the hanging wall of the Zou-Shi fault. Compared with practical information, the simulation results are consistent with the No. 51 exploration section of the western Xiangshan. In addition, on the basis of geological information provided by previous investigators, the model simulates the flow process of fluids under compressive stress fields. The result suggests that many tensional areas are formed, which can help the fluid flowing upward from deeper parts. The fluid is easy to concentrate on the breccia fractured zone between two volcanic layers, especially on the intersection parts with faults, resulting in the for- mation of favourable locations of mineralization. In addition, the model is significant in guiding the exploration of ura- nium deposits in the western Xiangshan and provides clues for further exploration of deposits.
文摘The kill characteristics of aimed warhead were studied. Emphasis on the improvement of initiation system, experiments and three dimensional numerical investigations were carried out. Simulation results of side three initiation points fit experiments well. Optimal initiation style is obtained through further simulation. It shows that the effective fragments and the effective kill energy of the optimal scheme increase 12.8% and 10.1% respectively.
基金financially supported by the Major Science and Technology Projects in Anhui Province (No. 18030901097)the Natural Science Foundation of Anhui Province (No.1908085QE197)the Fundamental Research Funds for the Central Universities (JZ2018HGBZ0133, JZ2019HGTA0043)
文摘Although the shell mould casting process has a wide range of application in many fields,the prediction of casting defects is still a problem.In the present work,a typical leaf spring bracket casting of ZG310-570 was fabricated by shell mold casting.The finite element model and ProCAST software were utilized for simulating the filling and solidification processes of the casting;and the formation mechanism of the gas pore,and shrinkage porosity defects were analyzed.The results indicate that the gas pore and shrinkage porosity defects are formed due to air entrapment,insufficient feeding and non-sequential solidification.Subsequently,through changing the position of risers,adding a connecting channel between the risers,and setting blind risers at the U-shaped brackets,an optimized gating and feeding system was established to improve the quality of the casting.After optimization,the gas pore and shrinkage porosity defects of the leaf spring bracket casting are effectively eliminated.The experiment results with the optimized casting process are in good agreement with the numerical simulation,which verifies the validity of the finite element model in the shell mould casting.
基金financially supported by the National Natural Science Foundation of China(Grant Nos.52005297 and 52035005)the Fundamental Research Funds of Shandong University(Grant No.2019GN003)。
文摘The tool with polygonal pin profile has been widely employed in friction stir welding(FSW) of aluminum, but there is hardly an effective optimization methodology existed as the thermomechanical characteristics affected by pins with various flats number have not been understood comprehensively. Therefore, the present work employs a 3-dimensional computational fluid dynamics(CFD) model to have an integrated observation of the FSW process with the effect of polygonal pin profiles. Both the heat generation modes due to contact friction at the tool–workpiece interface and volumetric viscous dissipation in the vicinity of the tool are considered. The model is utilized to give a quantitative analysis of the heat generation, temperature distribution, plastic material flow and welding loads during the FSW process for various tools with polygonal pin profiles, as well as a variety of shoulder diameters, welding speeds and tool rotation speeds. The calculated results of thermal cycles, tool torques and joint cross sections for some typical polygonal pins and welding parameters are all found to be compared well with the experimental ones, which demonstrates the feasibility and applicability of the present numerical model. Particularly, a methodology is developed for the optimization of the flats number by identifying the torque components in both parallel and vertical direction of the pin-side flat region. The results show that the optimized pin flats number increases with increasing tool rotation speed, while the influence of both welding speed and shoulder diameter can be supposed to be insignificant. Moreover, the dependability of the optimized results is also discussed by considering wear tendency and service life of the pin for multiple welding conditions.
文摘Substrate, a typical ultra-slender aluminum alloy structural components with a large aspect ratio and complex internal structure, was traditionally manufactured by re-assembly and sub-welding. In order to realize the monoblock casting of the substrate, the Pro/E software was utilized to carry out three-dimensional(3D) modeling of the substrate casting, and the filling and solidification processes were calculated, as well as the location and types of casting defects were predicted by the casting simulation software Anycasting. Results of the filling process simulation show that the metal liquid is distributed into each gap runner evenly and smoothly. There is no serious vortex phenomenon in the mold cavity, and the trajectory of the virtual particles is clear. Results of the solidification process simulation show that shrinkage cavities mainly appear at the junction of gap runners and the rail surface of the substrate. The average deformation is 0.6 mm in X direction, 3.8 mm in Y direction, and 8.2 mm in Z direction. Based on the simulation results, the casting process of the substrate was optimized, and qualified castings were successfully produced, which will provide a reference for the casting process design of other ultraslender aluminum alloy structural components.
基金Project (50904027) supported by the National Natural Science Foundation of ChinaProject (2013BAB03B05) supported by the National Key Technology R&D Program of China+1 种基金Project (20133BCB23018) supported by the Foundation for Young Scientist(Jinggang Star)of Jiangxi Province,ChinaProject (2012ZBAB206002) supported by the Natural Science Foundation of Jiangxi Province,China
文摘According to the innate characteristic of four types of furnace, the copper flash continuous smelting （CFCS） furnace can be considered a synthetic reactor of two relatively independent processes： flash matte smelting process （FMSP） and copper continuous converting process （CCCP）. Then, the CFCS thermodynamic model was proposed by establishing the multi-phase equilibrium model of FMSP and the local-equilibrium model of CCCP, respectively, and by combining them through the smelting intermediates. Subsequently, the influences of the furnace structures were investigated using the model on the formation of blister copper, the Fe3O4 behavior, the copper loss in slag and the copper recovery rate. The results show that the type D furnace, with double flues and a slag partition wall, is an ideal CFCS reactor compared with the other three types furnaces. For CFCS, it is effective to design a partition wall in the furnace to make FMSP and CCCP perform in two relatively independent zones, respectively, and to make smelting gas and converting gas discharge from respective flues.
文摘Plastic injection molding is a very complex process and its process planning has a direct influence on product quality and production efficiency. This paper studied the optimization of injection molding process by combining the numerical simulation with back-propagation(BP) networks. The BP networks are trained by the results of numerical simulation. The trained BP networks may:(1) shorten time for process planning;(2) optimize process parameters;(3) be employed in on-line quality control;(4) be integrated with knowledge-based system(KBS) and case-based reasoning(CBR) to make intelligent process planning of injection molding.
基金supported by National Natural Science Foundation of China(52336005 and 52106133).
文摘Circulating fluidized bed flue gas desulfurization(CFB-FGD) process has been widely applied in recent years. However, high cost caused by the use of high-quality slaked lime and difficult operation due to the complex flow field are two issues which have received great attention. Accordingly, a laboratory-scale fluidized bed reactor was constructed to investigate the effects of physical properties and external conditions on desulfurization performance of slaked lime, and the conclusions were tried out in an industrial-scale CFB-FGD tower. After that, a numerical model of the tower was established based on computational particle fluid dynamics(CPFD) and two-film theory. After comparison and validation with actual operation data, the effects of operating parameters on gas-solid distribution and desulfurization characteristics were investigated. The results of experiments and industrial trials showed that the use of slaked lime with a calcium hydroxide content of approximately 80% and particle size greater than 40 μm could significantly reduce the cost of desulfurizer. Simulation results showed that the flow field in the desulfurization tower was skewed under the influence of circulating ash. We obtained optimal operating conditions of 7.5 kg·s^(-1)for the atomized water flow, 70 kg·s^(-1)for circulating ash flow, and 0.56 kg·s^(-1)for slaked lime flow, with desulfurization efficiency reaching 98.19% and the exit flue gas meeting the ultraclean emission and safety requirements. All parameters selected in the simulation were based on engineering examples and had certain application reference significance.
文摘Live bone inherently responds to applied mechanical stimulus by altering its internal tissue composition and ultimately biomechanical properties, structure and function. The final formation may structurally appear inferior by design but complete by function. To understand the loading response, this paper numerically investigated structural remodeling of mature sheep femur using evolutionary structural optimization method (ESO). Femur images from Computed Tomography scanner were used to determine the elastic modulus variation and subsequently construct finite element model of the femur with stiffest elasticity measured. Major muscle forces on dominant phases of healthy sheep gait were imposed on the femur under static mode. ESO was applied to progressively alter the remodeling of numerically simulated femur from its initial to final design by iteratively removing elements with low strain energy density (SED). The computations were repeated with two different mesh sizes to test the convergence. The elements within the medullary canal had low SEDs and therefore were removed during the optimization. The SEDs in the remaining elements varied with angle around the circumference of the shaft. Those elements with low SED were inefficient in supporting the load and thus fundamentally explained how bone remodels itself with less stiff inferior tissue to meet load demand. This was in line with the Wolff’s law of transformation of bone. Tissue growth and remodeling process was found to shape the sheep femur to a mechanically optimized structure and this was initiated by SED in macro-scale according to traditional principle of Wolff’s law.
文摘Based on the study about the geological background of Beiya Gold Deposit, numerical simulation was conducted about the three-dimensional structural stress field for Beiya Gold Deposit by applying finite element theory and by employing a linear elasticity model. Results of the simulation indicate that the Beiya syncline is a faulted basin, and a hidden fracture occurs in the west wing of the syncline.Under the action of the EW-trending compressive force, four nearly NS-trending fractures (groups) were generated in the stress stretching areas of the two wings of the syncline, and these fractures constitute favorable tectonic positions for the upward intrusion of porphyry magma and the occurrence of Au-Pb-Zn polymetallic deposits.
文摘In this paper we use the finite element analysis software ANSYS10.0 to establish a finite element model for pressure gauge C -spring tube, and the main factors affected the relation between the pressure and distortion displacement are analyzed. The results show that with the increasing of the spring tube wall thickness T and the minor axis length B, the elastic rigidity of spring tube increases, which is reduced with spring tube diameter D. Moreover, the major axis length H increases. Meanwhile, a pressure gauge spring tube has been optimized according to the simulation results bused on a model with special features, and the design results achieve the intended purpose. The analysis results provide a reliable method for the research and design of similar elastic elements.
文摘The quality of skeleton system for the cheetah robot goes hand in hand with its bionic result of its shape, structure and functions. In view of the skeleton system constitution and structural characteristic of the cheetah, the team applied structure design, stimulation analysis and parameter optimization to developing the cheetah robot. In addition, after the invention of cheetah robot＇s anterior lumbar vertebra based on its functional attribute and connectivity attribute, the Solidworks Simulation was utilized to analyze the design, according to which improvement on the lumbar vertebra was made. Plus, the advantages of the CAD and CAE made the high efficiency of design work and high quality of the cheetah robot possible.
