For the congestion problems in high-speed networks, a genetic based fuzzy Q-learning flow controller is proposed. Because of the uncertainties and highly time-varying, it is not easy to accurately obtain the complete ...For the congestion problems in high-speed networks, a genetic based fuzzy Q-learning flow controller is proposed. Because of the uncertainties and highly time-varying, it is not easy to accurately obtain the complete information for high-speed networks. In this case, the Q-learning, which is independent of mathematic model, and prior-knowledge, has good performance. The fuzzy inference is introduced in order to facilitate generalization in large state space, and the genetic operators are used to obtain the consequent parts of fuzzy rules. Simulation results show that the proposed controller can learn to take the best action to regulate source flow with the features of high throughput and low packet loss ratio, and can avoid the occurrence of congestion effectively.展开更多
A binary available bit rate （ABR） scheme based on discrete-time variable structure control （DVSC） theory is proposed to solve the problem of asynchronous transfer mode （ATM） networks congestion in this paper. A ...A binary available bit rate （ABR） scheme based on discrete-time variable structure control （DVSC） theory is proposed to solve the problem of asynchronous transfer mode （ATM） networks congestion in this paper. A discrete-time system model with uncertainty is introduced to depict the time-varying ATM networks. Based on the system model, an asymptotically stable sliding surface is designed by linear matrix inequality （LMI）. In addition, a novel discrete-time reaching law that can obviously reduce chatter is also put forward. The proposed discrete-time variable structure controller can effectively constrain the oscillation of allowed cell rate （ACR） and the queue length in a router. Moreover, the controller is self-adaptive against the uncertainty in the system. Simulations are done in different scenarios. The results demonstrate that the controller has better stability and robustness than the traditional binary flow controller, so it is good for adequately exerting the simplicity of binary flow control mechanisms.展开更多
A dynamic network Qo S control mechanism was proposed based on traffic prediction. It first predicts network traffic flow and then dynamically distributes network resources, which makes full use of network flow self-s...A dynamic network Qo S control mechanism was proposed based on traffic prediction. It first predicts network traffic flow and then dynamically distributes network resources, which makes full use of network flow self-similarity and chaos. So it can meet changing network needs very well. The simulation results show that the dynamic Qo S control mechanism based on prediction has better network performance than that based on measurement.展开更多
Multipe NSSS (Nuclear Steam Supply System) modules use the common feeding-water system to drive the common turbine power generation set. The SSFFN (secondary side fluid flow network) of MHTGR plant has features i.e. s...Multipe NSSS (Nuclear Steam Supply System) modules use the common feeding-water system to drive the common turbine power generation set. The SSFFN (secondary side fluid flow network) of MHTGR plant has features i.e. strong-coupling and nonlinearity. A wide range of power switching operation will cause unsteady flow, which may destroy the working elements and will be a threat for normal operation. To overcome those problems, a differential-algebraic model and PI controllers are designed for the SSFFN. In MATLAB\SIMULINK environment, a simulation platform is established and used to make a simulation of SSFFN of a MHTGR plant with two NSSS modules, which uses feedwater valves to control the mass flow rate in each module instead of feedwater pump. Results reflect good robustness of controllers.展开更多
The flow pattern in a pipeline is a very important topic in petroleum exploitation. This paper is to classify the flow pattern of oil-gas-water flow in a pipeline by using BP neural network. The effects of different p...The flow pattern in a pipeline is a very important topic in petroleum exploitation. This paper is to classify the flow pattern of oil-gas-water flow in a pipeline by using BP neural network. The effects of different parameter combinations are investigated to find the most important ones. It is shown that BP neural network can be used in the analysis of the flow pattern of three-phase flow in pipelines. In most cases, the mean square error is large for the horizontal pipes. The optimized neuron number of the middle layer changes with conditions. So, we must changes the neuron number of the middle layer in simulation for any conditions to seek the best results. These conclusions can be taken as references for further study of the flow pattern of oil-gas-water in a pipeline.展开更多
Elevators are essential components of contemporary buildings, enabling efficient vertical mobility for occupants. However, the proliferation of tall buildings has exacerbated challenges such as traffic congestion with...Elevators are essential components of contemporary buildings, enabling efficient vertical mobility for occupants. However, the proliferation of tall buildings has exacerbated challenges such as traffic congestion within elevator systems. Many passengers experience dissatisfaction with prolonged wait times, leading to impatience and frustration among building occupants. The widespread adoption of neural networks and deep learning technologies across various fields and industries represents a significant paradigm shift, and unlocking new avenues for innovation and advancement. These cutting-edge technologies offer unprecedented opportunities to address complex challenges and optimize processes in diverse domains. In this study, LSTM (Long Short-Term Memory) network technology is leveraged to analyze elevator traffic flow within a typical office building. By harnessing the predictive capabilities of LSTM, the research aims to contribute to advancements in elevator group control design, ultimately enhancing the functionality and efficiency of vertical transportation systems in built environments. The findings of this research have the potential to reference the development of intelligent elevator management systems, capable of dynamically adapting to fluctuating passenger demand and optimizing elevator usage in real-time. By enhancing the efficiency and functionality of vertical transportation systems, the research contributes to creating more sustainable, accessible, and user-friendly living environments for individuals across diverse demographics.展开更多
Providing the required metrics for different service respectively is a basic characteristic in multi-service networks. The different service can be accessed and forwarded differently to provide the different transmiss...Providing the required metrics for different service respectively is a basic characteristic in multi-service networks. The different service can be accessed and forwarded differently to provide the different transmission performance. The state information between admission control and scheduling can be exchanged each other by the defined correlation coefficient to adjust the flow distribution in progress. The priority queue length measured by scheduler implicitly can describe the priority flows load. And the fair rate can describe the non-priority flows load. Different admission decision will be made according to the state of scheduler to assure the time-delay upper threshold for the priority flows under heavy load and the fairness for elastic flows in light load, respectively. The stability condition was conduced and proved. Simulation results show the policy can ensure both the delay for the priority flows and the minimal throughput for non-priority flows.展开更多
As the demand for more efficient and adaptable power distribution systems intensifies, especially in rural areas, innovative solutions like the Capacitor-Coupled Substation with a Controllable Network Transformer (CCS...As the demand for more efficient and adaptable power distribution systems intensifies, especially in rural areas, innovative solutions like the Capacitor-Coupled Substation with a Controllable Network Transformer (CCS-CNT) are becoming increasingly critical. Traditional power distribution networks, often limited by unidirectional flow capabilities and inflexibility, struggle to meet the complex demands of modern energy systems. The CCS-CNT system offers a transformative approach by enabling bidirectional power flow between high-voltage transmission lines and local distribution networks, a feature that is essential for integrating renewable energy sources and ensuring reliable electrification in underserved regions. This paper presents a detailed mathematical representation of power flow within the CCS-CNT system, emphasizing the control of both active and reactive power through the adjustment of voltage levels and phase angles. A control algorithm is developed to dynamically manage power flow, ensuring optimal performance by minimizing losses and maintaining voltage stability across the network. The proposed CCS-CNT system demonstrates significant potential in enhancing the efficiency and reliability of power distribution, making it particularly suited for rural electrification and other applications where traditional methods fall short. The findings underscore the system's capability to adapt to varying operational conditions, offering a robust solution for modern power distribution challenges.展开更多
For the great significance of the prediction of control parameters selected for hot-rolling and the evaluation of hot-rolling quality for the analysis of prod uction problems and production management, the selection o...For the great significance of the prediction of control parameters selected for hot-rolling and the evaluation of hot-rolling quality for the analysis of prod uction problems and production management, the selection of hot-rolling control parameters was studied for microalloy steel by following the neural network principle. An experimental scheme was first worked out for acquisition of sample data, in which a gleeble-1500 thermal simolator was used to obtain rolling temperature, strain, stain rate, and stress-strain curves. And consequently the aust enite grain sizes was obtained through microscopic observation. The experimental data was then processed through regression. By using the training network of BP algorithm, the mapping relationship between the hotrooling control parameters (rolling temperature, stain, and strain rate) and the microstructural paramete rs (austenite grain in size and flow stress) of microalloy steel was function appro ached for the establishment of a neural network-based model of the austeuite grain size and flow stress of microalloy steel. From the results of estimation made with the neural network based model, the hot-rolling control parameters can be effectively predicted.展开更多
OpenFlow网络数据平面将未匹配流表的数据包发送给控制器,其中的无连接突发流量将产生冗余控制报文,对网络性能造成不良影响,而目前的OpenFlow协议并未对此进行处理.研究了在控制平面和数据平面分别消除冗余控制报文的方法 ERCMC(elimin...OpenFlow网络数据平面将未匹配流表的数据包发送给控制器,其中的无连接突发流量将产生冗余控制报文,对网络性能造成不良影响,而目前的OpenFlow协议并未对此进行处理.研究了在控制平面和数据平面分别消除冗余控制报文的方法 ERCMC(eliminating redundant control messages on the control plane)和ERCMD(eliminating redundant control messages on the data plane),分别在NOX和Open vSwitch上进行实现,并进行性能评价.实验结果表明,ERCMC方法能够消除冗余控制报文,但增加了额外的处理开销;ERCMD方法在减少冗余控制报文数量的情况下能够减小控制器和OpenFlow交换机负载.展开更多
随着软件定义网络(Software Defined Network,SDN)成为网络世界的新的范式转移,作为SDN网络的核心组件,控制器的性能得到了越来越多的关注。文章介绍了基于Open Flow 1.3这一南向协议的SDN控制器性能测试方法,并以某开源控制器为例,介...随着软件定义网络(Software Defined Network,SDN)成为网络世界的新的范式转移,作为SDN网络的核心组件,控制器的性能得到了越来越多的关注。文章介绍了基于Open Flow 1.3这一南向协议的SDN控制器性能测试方法,并以某开源控制器为例,介绍测试结果的定量呈现方式和分析方法,为需要评估控制器性能的用户提供参考。展开更多
A multipoint excitation experiment system of the 1Cr18Ni9 steel plate-pipe network as the main vibration body was established,which used transient flow produced by the wave exciter to excite the 1Cr18Ni9 steel plate-p...A multipoint excitation experiment system of the 1Cr18Ni9 steel plate-pipe network as the main vibration body was established,which used transient flow produced by the wave exciter to excite the 1Cr18Ni9 steel plate-pipe network to vibrate.The experimental results show that the 1Cr18Ni9 steel plate vibrates in three dimensions.The vibrations of the particles of the steel plate distributing along the pipe＇s axial have phase differences and take place near the cylinder side first.Therefore,it is a multipoint vibration mode.The amplitude of the 1Cr18Ni9 steel plate increases as the system pressure increases and decreases as the wave exciter＇s frequency decreases.The vibration intensity of the particles of the 1Cr18Ni9 steel plate close to the cylinder is the strongest and the amplitude is the highest in Y direction at a given system frequency.The vibration intensity of the particles close to the wave exciter is the strongest and the amplitude is the smallest in Z direction at a given system pressure.展开更多
可编程性恢复是软件定义广域网(Software Defined Wide Area Network, SD-WAN)中节点失效后保障网络服务质量的有效方法 .针对可编程性恢复中失效节点形式单一的问题,提出一种基于启发式算法的主备份控制器部署方法来确保交换机和控制...可编程性恢复是软件定义广域网(Software Defined Wide Area Network, SD-WAN)中节点失效后保障网络服务质量的有效方法 .针对可编程性恢复中失效节点形式单一的问题,提出一种基于启发式算法的主备份控制器部署方法来确保交换机和控制器失效时网络的可编程性.在主控制器部署时,利用控制路径密度和强度衡量域内控制路径的可靠性,提升交换机故障情况下的路径可编程性;在备份控制器部署时,将一定数量的、相邻的主控制域划分为多个备份区域,在备份区域中部署一个备份控制器,建立它与交换机的映射策略,使脱机交换机以及离线流的恢复能力最大化,以提升控制器故障情况下的离线流的可编程性.此外,重新定义狼群算法的智能行为,提出一种离散狼群算法解决主备控制器的部署问题.在四种真实网络拓扑上进行实验,结果表明提出的方法在交换机故障的情况下能降低失效控制路径的影响,在控制器故障时能最大程度上恢复离线流.展开更多
文摘For the congestion problems in high-speed networks, a genetic based fuzzy Q-learning flow controller is proposed. Because of the uncertainties and highly time-varying, it is not easy to accurately obtain the complete information for high-speed networks. In this case, the Q-learning, which is independent of mathematic model, and prior-knowledge, has good performance. The fuzzy inference is introduced in order to facilitate generalization in large state space, and the genetic operators are used to obtain the consequent parts of fuzzy rules. Simulation results show that the proposed controller can learn to take the best action to regulate source flow with the features of high throughput and low packet loss ratio, and can avoid the occurrence of congestion effectively.
基金the National Natural Science Foundation of China (No.60274009)Specialized Research Fund for the DoctoralProgram of Higher Education (No.20020145007)
文摘A binary available bit rate （ABR） scheme based on discrete-time variable structure control （DVSC） theory is proposed to solve the problem of asynchronous transfer mode （ATM） networks congestion in this paper. A discrete-time system model with uncertainty is introduced to depict the time-varying ATM networks. Based on the system model, an asymptotically stable sliding surface is designed by linear matrix inequality （LMI）. In addition, a novel discrete-time reaching law that can obviously reduce chatter is also put forward. The proposed discrete-time variable structure controller can effectively constrain the oscillation of allowed cell rate （ACR） and the queue length in a router. Moreover, the controller is self-adaptive against the uncertainty in the system. Simulations are done in different scenarios. The results demonstrate that the controller has better stability and robustness than the traditional binary flow controller, so it is good for adequately exerting the simplicity of binary flow control mechanisms.
基金Funded by the National Natural Science Foundation of China(No.41301084)the Scientific Research Project of Hunan Province Education Department,China(No.13C713)the Natural Science Foundation of Hunan Province,China(No.13JJ6075)
文摘A dynamic network Qo S control mechanism was proposed based on traffic prediction. It first predicts network traffic flow and then dynamically distributes network resources, which makes full use of network flow self-similarity and chaos. So it can meet changing network needs very well. The simulation results show that the dynamic Qo S control mechanism based on prediction has better network performance than that based on measurement.
文摘Multipe NSSS (Nuclear Steam Supply System) modules use the common feeding-water system to drive the common turbine power generation set. The SSFFN (secondary side fluid flow network) of MHTGR plant has features i.e. strong-coupling and nonlinearity. A wide range of power switching operation will cause unsteady flow, which may destroy the working elements and will be a threat for normal operation. To overcome those problems, a differential-algebraic model and PI controllers are designed for the SSFFN. In MATLAB\SIMULINK environment, a simulation platform is established and used to make a simulation of SSFFN of a MHTGR plant with two NSSS modules, which uses feedwater valves to control the mass flow rate in each module instead of feedwater pump. Results reflect good robustness of controllers.
文摘The flow pattern in a pipeline is a very important topic in petroleum exploitation. This paper is to classify the flow pattern of oil-gas-water flow in a pipeline by using BP neural network. The effects of different parameter combinations are investigated to find the most important ones. It is shown that BP neural network can be used in the analysis of the flow pattern of three-phase flow in pipelines. In most cases, the mean square error is large for the horizontal pipes. The optimized neuron number of the middle layer changes with conditions. So, we must changes the neuron number of the middle layer in simulation for any conditions to seek the best results. These conclusions can be taken as references for further study of the flow pattern of oil-gas-water in a pipeline.
文摘Elevators are essential components of contemporary buildings, enabling efficient vertical mobility for occupants. However, the proliferation of tall buildings has exacerbated challenges such as traffic congestion within elevator systems. Many passengers experience dissatisfaction with prolonged wait times, leading to impatience and frustration among building occupants. The widespread adoption of neural networks and deep learning technologies across various fields and industries represents a significant paradigm shift, and unlocking new avenues for innovation and advancement. These cutting-edge technologies offer unprecedented opportunities to address complex challenges and optimize processes in diverse domains. In this study, LSTM (Long Short-Term Memory) network technology is leveraged to analyze elevator traffic flow within a typical office building. By harnessing the predictive capabilities of LSTM, the research aims to contribute to advancements in elevator group control design, ultimately enhancing the functionality and efficiency of vertical transportation systems in built environments. The findings of this research have the potential to reference the development of intelligent elevator management systems, capable of dynamically adapting to fluctuating passenger demand and optimizing elevator usage in real-time. By enhancing the efficiency and functionality of vertical transportation systems, the research contributes to creating more sustainable, accessible, and user-friendly living environments for individuals across diverse demographics.
基金Supported by the National Natural Science Foundation of China (No. 60872002, 61003237)the Open Research Foundation of National Mobile Communications Research Lab, Southeast University, China (W200912)the Natural Science Foundation of Nantong Universty (No. 08Z025)
文摘Providing the required metrics for different service respectively is a basic characteristic in multi-service networks. The different service can be accessed and forwarded differently to provide the different transmission performance. The state information between admission control and scheduling can be exchanged each other by the defined correlation coefficient to adjust the flow distribution in progress. The priority queue length measured by scheduler implicitly can describe the priority flows load. And the fair rate can describe the non-priority flows load. Different admission decision will be made according to the state of scheduler to assure the time-delay upper threshold for the priority flows under heavy load and the fairness for elastic flows in light load, respectively. The stability condition was conduced and proved. Simulation results show the policy can ensure both the delay for the priority flows and the minimal throughput for non-priority flows.
文摘As the demand for more efficient and adaptable power distribution systems intensifies, especially in rural areas, innovative solutions like the Capacitor-Coupled Substation with a Controllable Network Transformer (CCS-CNT) are becoming increasingly critical. Traditional power distribution networks, often limited by unidirectional flow capabilities and inflexibility, struggle to meet the complex demands of modern energy systems. The CCS-CNT system offers a transformative approach by enabling bidirectional power flow between high-voltage transmission lines and local distribution networks, a feature that is essential for integrating renewable energy sources and ensuring reliable electrification in underserved regions. This paper presents a detailed mathematical representation of power flow within the CCS-CNT system, emphasizing the control of both active and reactive power through the adjustment of voltage levels and phase angles. A control algorithm is developed to dynamically manage power flow, ensuring optimal performance by minimizing losses and maintaining voltage stability across the network. The proposed CCS-CNT system demonstrates significant potential in enhancing the efficiency and reliability of power distribution, making it particularly suited for rural electrification and other applications where traditional methods fall short. The findings underscore the system's capability to adapt to varying operational conditions, offering a robust solution for modern power distribution challenges.
文摘For the great significance of the prediction of control parameters selected for hot-rolling and the evaluation of hot-rolling quality for the analysis of prod uction problems and production management, the selection of hot-rolling control parameters was studied for microalloy steel by following the neural network principle. An experimental scheme was first worked out for acquisition of sample data, in which a gleeble-1500 thermal simolator was used to obtain rolling temperature, strain, stain rate, and stress-strain curves. And consequently the aust enite grain sizes was obtained through microscopic observation. The experimental data was then processed through regression. By using the training network of BP algorithm, the mapping relationship between the hotrooling control parameters (rolling temperature, stain, and strain rate) and the microstructural paramete rs (austenite grain in size and flow stress) of microalloy steel was function appro ached for the establishment of a neural network-based model of the austeuite grain size and flow stress of microalloy steel. From the results of estimation made with the neural network based model, the hot-rolling control parameters can be effectively predicted.
文摘OpenFlow网络数据平面将未匹配流表的数据包发送给控制器,其中的无连接突发流量将产生冗余控制报文,对网络性能造成不良影响,而目前的OpenFlow协议并未对此进行处理.研究了在控制平面和数据平面分别消除冗余控制报文的方法 ERCMC(eliminating redundant control messages on the control plane)和ERCMD(eliminating redundant control messages on the data plane),分别在NOX和Open vSwitch上进行实现,并进行性能评价.实验结果表明,ERCMC方法能够消除冗余控制报文,但增加了额外的处理开销;ERCMD方法在减少冗余控制报文数量的情况下能够减小控制器和OpenFlow交换机负载.
文摘随着软件定义网络(Software Defined Network,SDN)成为网络世界的新的范式转移,作为SDN网络的核心组件,控制器的性能得到了越来越多的关注。文章介绍了基于Open Flow 1.3这一南向协议的SDN控制器性能测试方法,并以某开源控制器为例,介绍测试结果的定量呈现方式和分析方法,为需要评估控制器性能的用户提供参考。
基金Funded by the International S&T Cooperation Program of China(No. 2011DFA72120)the Program for Innovation Research Team in University of Shanxi Province(No.2011018022)the University Young and Middle-aged Top-notch Innovative Talent Program of Shanxi Province(No.20091020235)
文摘A multipoint excitation experiment system of the 1Cr18Ni9 steel plate-pipe network as the main vibration body was established,which used transient flow produced by the wave exciter to excite the 1Cr18Ni9 steel plate-pipe network to vibrate.The experimental results show that the 1Cr18Ni9 steel plate vibrates in three dimensions.The vibrations of the particles of the steel plate distributing along the pipe＇s axial have phase differences and take place near the cylinder side first.Therefore,it is a multipoint vibration mode.The amplitude of the 1Cr18Ni9 steel plate increases as the system pressure increases and decreases as the wave exciter＇s frequency decreases.The vibration intensity of the particles of the 1Cr18Ni9 steel plate close to the cylinder is the strongest and the amplitude is the highest in Y direction at a given system frequency.The vibration intensity of the particles close to the wave exciter is the strongest and the amplitude is the smallest in Z direction at a given system pressure.
文摘可编程性恢复是软件定义广域网(Software Defined Wide Area Network, SD-WAN)中节点失效后保障网络服务质量的有效方法 .针对可编程性恢复中失效节点形式单一的问题,提出一种基于启发式算法的主备份控制器部署方法来确保交换机和控制器失效时网络的可编程性.在主控制器部署时,利用控制路径密度和强度衡量域内控制路径的可靠性,提升交换机故障情况下的路径可编程性;在备份控制器部署时,将一定数量的、相邻的主控制域划分为多个备份区域,在备份区域中部署一个备份控制器,建立它与交换机的映射策略,使脱机交换机以及离线流的恢复能力最大化,以提升控制器故障情况下的离线流的可编程性.此外,重新定义狼群算法的智能行为,提出一种离散狼群算法解决主备控制器的部署问题.在四种真实网络拓扑上进行实验,结果表明提出的方法在交换机故障的情况下能降低失效控制路径的影响,在控制器故障时能最大程度上恢复离线流.
