By using aluminum alloys,the properties of the material in sheet hydroforming were obtained based on the identification of parameters for constitutive models by inverse modeling in which the friction coefficients were...By using aluminum alloys,the properties of the material in sheet hydroforming were obtained based on the identification of parameters for constitutive models by inverse modeling in which the friction coefficients were also considered in 2D and 3D simulations.With consideration of identified simulation parameters by inverse modeling,some key process parameters including tool dimensions and pre-bulging on the forming processes in sheet hydroforming were investigated and optimized.Based on the optimized parameters,the sheet hydroforming process can be analyzed more accurately to improve the robust design.It proves that the results from simulation based on the identified parameters are in good agreement with those from experiments.展开更多
Inverse method was used in single crystal superalloy DD6 processing simulation during solidification. Numerical modeling coupled with experiments has been used to estimate the interface heat transfer coefficient （IHT...Inverse method was used in single crystal superalloy DD6 processing simulation during solidification. Numerical modeling coupled with experiments has been used to estimate the interface heat transfer coefficient （IHTC） between the surface of slab casting and inner mold. Calculated temperature dependent values of IHTC were obtained from a numerical solution. The calculated temperatures agreed well with the measurement of cooling profile.展开更多
The maneuvering flight governing equations for coaxial rotor helicopters are established. By introducing induced velocity interference factor analysis, the coaxial rotor aerodynamic interference can be taken into acc...The maneuvering flight governing equations for coaxial rotor helicopters are established. By introducing induced velocity interference factor analysis, the coaxial rotor aerodynamic interference can be taken into account. With the combination of coaxial rotor helicopter control features and nonlinear inverse solution technique, the governing equations for maneuvering flight can be solved so as to determine helicopter control input, control force and moment, and helicopter body attitudes which are needed for performing the defined maneuver. Finally, as an example of this methods engineering application, the calculated results with level turn, lateral jink maneuvers are presented and simply analyzed.展开更多
Maneuverability is a key factor to determine whether a helicopter could finish certain flight missions successfully or not. Inverse simulation is commonly used to calculate the pilot controls of a helicopter to comple...Maneuverability is a key factor to determine whether a helicopter could finish certain flight missions successfully or not. Inverse simulation is commonly used to calculate the pilot controls of a helicopter to complete a certain kind of maneuver flight and to assess its maneuverability.A general method for inverse simulation of maneuver flight for helicopters with the flight control system online is developed in this paper. A general mathematical describing function is established to provide mathematical descriptions of different kinds of maneuvers. A comprehensive control solver based on the optimal linear quadratic regulator theory is developed to calculate the pilot controls of different maneuvers. The coupling problem between pilot controls and flight control system outputs is well solved by taking the flight control system model into the control solver. Inverse simulation of three different kinds of maneuvers with different agility requirements defined in the ADS-33 E-PRF is implemented based on the developed method for a UH-60 helicopter. The results show that the method developed in this paper can solve the closed-loop inverse simulation problem of helicopter maneuver flight with high reliability as well as efficiency.展开更多
Based on the theory of finite element analysis, an inverse analysis model for the comprehensive medium parameters of the Qinghai-Tibet Plateau is set up. With the help of GPS velocity field, the comprehensive crustal ...Based on the theory of finite element analysis, an inverse analysis model for the comprehensive medium parameters of the Qinghai-Tibet Plateau is set up. With the help of GPS velocity field, the comprehensive crustal medium parameters of the plateau are inversely analyzed and the characteristics of the related movement macroscopically simulated. It is then concluded that the tectonic deformation of the plateau is mainly in the form of a N-S compression accompanied by an E-W stretching, and the present tectonic setting of the plateau should be the result of the collision between the Indian and the Eurasian continents during the Cenozoic.展开更多
The appearance of lower hardness at the surface than at the core after through-hardening of steels is known as "inverse quench-hardening." Pioneering work was performed in the 1970s by establishing a simple ...The appearance of lower hardness at the surface than at the core after through-hardening of steels is known as "inverse quench-hardening." Pioneering work was performed in the 1970s by establishing a simple test procedure where cylindrical specimens were cooled by air and brine sequentially to produce the effect. This phenomenon was described in relation to the polymer quenching and its effect to the improvement in the fatigue strength of the steel in the 1990s. The hardening mechanism in the same specimens as the pioneering work was recently examined using a finite element simulation method. However, this work has not been completed for lack of experimental quenching cooling curves for the comparisons. In this study, the same experiments using 20mm diameter cylindrical specimens as those of the pioneering work were conducted to obtain cooling curves and hardness distributions for comparing simulated results. Experimental cooling curves showed a temperature recovery as predicted by the simulation. Also the inverse quench-hardening phenomena were found in the measured and simulated hardness distributions of the specimens.展开更多
Based on the convection and diffusion mechanisms of radon migration, in this paper we deduce the two-dimensional differential equation for radon transportation in the overburden above active fault zones with an unlimi...Based on the convection and diffusion mechanisms of radon migration, in this paper we deduce the two-dimensional differential equation for radon transportation in the overburden above active fault zones with an unlimited extension along the strike. Making use of the finite difference method, the radon concentration distribution in the overburden above active faults is calculated and modeled. The active fault zone parameters, such as the depth and the width of the fault zone, and the value of radon concentration, can be inverted from the measured radon concentration curve. These realize quantitative interpretation for radon concentration anomalies. The inversion results are in good agreement with the actual fault zone parameters.展开更多
Some missions have been carried out to measure wave directional spectrum by synthetic aperture radar （SAR） and airborne real aperture radar （RAR） at a low incidence.Both them have their own advantages and limitati...Some missions have been carried out to measure wave directional spectrum by synthetic aperture radar （SAR） and airborne real aperture radar （RAR） at a low incidence.Both them have their own advantages and limitations.Scientists hope that SAR and satellite-based RAR can complement each other for the research on wave properties in the future.For this study,the authors aim to simulate the satellite-based RAR system to validate performance for measuring the directional wave spectrum.The principal measurements are introduced and the simulation methods based on the one developed by Hauser are adopted and slightly modified.To enhance the authenticity of input spectrum and the wave spectrum measuring consistency for SAR and satellite-based RAR,the wave height spectrum inversed from Envisat ASAR data by cross spectrum technology is used as the input spectrum of the simulation system.In the process of simulation,the sea surface,backscattering signal,modulation spectrum and the estimated wave height spectrum are simulated in each look direction.Directional wave spectrum are measured based on the simulated observations from 0 ？ to 360 ？ .From the estimated wave spectrum,it has an 180 ？ ambiguity like SAR,but it has no special high wave number cut off in all the direction.Finally,the estimated spectrum is compared with the input one in terms of the dominant wave wavelength,direction and SWH and the results are promising.The simulation shows that satellite-based RAR should be capable of measuring the directional wave properties.Moreover,it indicates satellite-based RAR basically can measure waves that SAR can measure.展开更多
Deeply buried mountain tunnels are often exposed to the risk of rock bursts,which always cause serious damage to the supporting structures and threaten the safety of the engineers.Due to the limited data available,a s...Deeply buried mountain tunnels are often exposed to the risk of rock bursts,which always cause serious damage to the supporting structures and threaten the safety of the engineers.Due to the limited data available,a suitable approach to predict the rockburst tendency at the preliminary stage becomes very important.In this study,an integrated methodology combining 3D initial stress inversion and rockburst tendency prediction was developed and subsequently applied to a case study of the Sangzhuling Tunnel on the Sichuan–Tibet Railway.The numerical modelling involved inverting the initial stress field using a multiple linear regression method.The tunnel excavation was simulated separately by FDM and DEM,based on a stress boundary condition from the inverted stress field.The comparative analysis demonstrates that the rockburst ratio calculated using DEM(76.70%)exhibits a slight increase compared to FDM(75.38%),and the rockburst location is consistent with the actual situation.This suggests that DEM is more suitable for simulating the stress redistribution during excavation in a jointed rock mass.The numerical simulation combined with the deviatoric stress approach effectively predicts rockburst tendency,meeting the engineering requirements.Despite its limitations,numerical simulation remains a reliable method for predicting rock bursts.展开更多
The high-speed winding spindle employs a flexible support system incorporating rubber O-rings.By precisely configuring the structural parameters and the number of the O-rings,the spindle can stably surpass its critica...The high-speed winding spindle employs a flexible support system incorporating rubber O-rings.By precisely configuring the structural parameters and the number of the O-rings,the spindle can stably surpass its critical speed points and maintain operational stability across the entire working speed range.However,the support stiffness and damping of rubber O-rings exhibit significant nonlinear frequency dependence.Conventional experimental methods for deriving equivalent stiffness and damping,based on the principle of the forced non-resonance method,require fabricating custom setups for each O-ring specification and conducting vibration tests at varying frequencies,resulting in low efficiency and high costs.This study proposes a hybrid simulation-experimental method for dynamic parameter identification.Firstly,the frequency-dependent dynamic parameters of a specific O-ring support system are experimentally obtained.Subsequently,a corresponding parametric finite element model is established to simulate and solve the equivalent elastic modulus and equivalent stiffness-damping coefficient of this O-ring support system.Ultimately,after iterative simulation,the simulated and experimental results achieve a 99.7%agreement.The parametric finite element model developed herein can directly simulate and inversely estimate frequency-dependent dynamic parameters for O-rings of different specifications but identical elastic modulus.展开更多
Microscopic traffic simulations are useful for solving various trafficrelated problems,e.g.traffic jams and accidents,local and global environmental and energy problems,maintaining mobility in aging societies,and evac...Microscopic traffic simulations are useful for solving various trafficrelated problems,e.g.traffic jams and accidents,local and global environmental and energy problems,maintaining mobility in aging societies,and evacuation planning for natural as well as man-made disasters.The origin-destination(OD)matrix is often used as the input to represent traffic demands into traffic simulators.In this study,we propose an indirect method for estimating the OD matrix using a traffic simulator as an internal model.The proposed method is designed to output results that are consistent with the input of the simulator.The method consists of the following steps:(1)calculating link traffic volume from the OD matrix,and(2)updating the matrix.The estimated matrix is updated iteratively until it converges to a predefined tolerance level.Numerical experiments are then conducted using the proposed method on a grid network and on a representation of an actual road network.Finally,we discuss the characteristics of the proposed method and the non-negative constraint for the traffic volume.展开更多
A double-walled tubular component can be formed from a metal tube under axial compression by inversion. Numerical simulation and experimental investigation show that die radius is the predominant factor affecting the ...A double-walled tubular component can be formed from a metal tube under axial compression by inversion. Numerical simulation and experimental investigation show that die radius is the predominant factor affecting the deformation process. For the given dimensions of 3A21 aluminium alloy tube, the feasible die radius varies between 2-4mm. The deformation process predicted by the finite element simulation agrees with the experiment results well.展开更多
Based on the boundary layer data of winter dense fog in 2007 from Nanjing University of Information Science & Technology,the profile characteristics of temperature,wind direction,wind speed and humidity in a dense...Based on the boundary layer data of winter dense fog in 2007 from Nanjing University of Information Science & Technology,the profile characteristics of temperature,wind direction,wind speed and humidity in a dense fog weather on December 13-14 in 2007 were analyzed,as well as their evolution laws in the formation and dispersion of fog,and the boundary layer characteristics of winter dense fog in Nanjing were revealed,while the development of fog was simulated by means of mesoscale numerical model.The results showed that the formation and dispersion of fog was greatly affected by inversion and humidity in the surface layer,and the wind direction in the surface layer also had effect on the formation and dispersion of advection fog.Mesoscale numerical model could preferably simulate the evolution of temperature,humidity,vertical speed in the development of fog,and the simulation of water vapor content in the fog could forecast the formation and dispersion of fog.展开更多
In order to explore the influence of welding parameters and to investigate the Al alloy (AA) nugget formation process, a comprehensive model involving electrical-thermal-mechanical and metallurgical analysis was estab...In order to explore the influence of welding parameters and to investigate the Al alloy (AA) nugget formation process, a comprehensive model involving electrical-thermal-mechanical and metallurgical analysis was established to numerically display the resistance spot welding (RSW) process within multiple fields and understand the AA-RSW physics. A multi-disciplinary finite element method (FEM) framework and a empirical sub-model were built to analyze the affecting factors on weld nugget and the underlying nature of welding physics with dynamic simulation procedure. Specifically, a counter-intuitive phenomenon of the resistance time-variation caused by the transient inverse virtual variation (TIVV) effect was highlighted and analyzed on the basis of welding current and temperature distribution simulation. The empirical model describing the TIVV phenomenon was used for modifying the dynamic resistance simulation during the AA spot welding process. The numerical and experimental results show that the proposed multi-field FEM model agrees with the measured AA welding feature, and the modified dynamic resistance model captures the physics of nugget growth and the electrical-thermal behavior under varying welding current and fluctuating heat input.展开更多
This paper describes a dual-stroke acting hydraulic power take-off （PTO） system employed in the wave energy converter （WEC） with an inverse pendulum. The hydraulic PTO converts slow irregular reciprocating wave mo...This paper describes a dual-stroke acting hydraulic power take-off （PTO） system employed in the wave energy converter （WEC） with an inverse pendulum. The hydraulic PTO converts slow irregular reciprocating wave motions to relatively smooth, fast rotation of an electrical generator. The design of the hydraulic PTO system and its control are critical to maximize the generated power. A time domain simulation study and the laboratory experiment of the full-scale beach test are presented. The results of the simulation and laboratory experiments including their comparison at full-scale are also presented, which have validated the rationality of the design and the reliability of some key components of the prototype of the WEC with an inverse pendulum with the dual-stroke acting hydraulic PTO system.展开更多
The entrainment flux ratio Ae and the inversion layer （IL） thickness are two key parameters in a mixed layer model. Ae is defined as the ratio of the entrainment heat flux at the mixed layer top to the surface heat ...The entrainment flux ratio Ae and the inversion layer （IL） thickness are two key parameters in a mixed layer model. Ae is defined as the ratio of the entrainment heat flux at the mixed layer top to the surface heat flux. The IL is the layer between the mixed layer and the free atmosphere. In this study, a parameterization of Ae is derived from the TKE budget in the first- order model for a well-developed CBL under the condition of linearly sheared geostrophic velocity with a zero value at the surface. It is also appropriate for a CBL under the condition of geostrophic velocity remaining constant with height. LESs are conducted under the above two conditions to determine the coefficients in the parameterization scheme. Results suggest that about 43% of the shear-produced TKE in the IL is available for entrainment, while the shear-produced TKE in the mixed layer and surface layer have little effect on entrainment. Based on this scheme, a new scale of convective turbulence velocity is proposed and applied to parameterize the IL thickness, The LES outputs for the CBLs under the condition of linearly sheared geostrophic velocity with a non-zero surface value are used to verify the performance of the parameterization scheme. It is found that the parameterized Ae and IL thickness agree well with the LES outputs.展开更多
Surface wave methods are becoming increasingly popular in many geotechnical applications and in earthquake seismology due to their noninvasive characteristics.Inverse surface wave dispersion curves are a crucial step ...Surface wave methods are becoming increasingly popular in many geotechnical applications and in earthquake seismology due to their noninvasive characteristics.Inverse surface wave dispersion curves are a crucial step in most surface wave methods.Many inversion methods have been applied to surface wave dispersion curve inversion,including linearized inversion and nonlinearized inversion methods.In this study,a hybrid inversion method of Damped Least Squares(DLS) with Very Fast Simulated Annealing(VFSA) is developed for multi-mode Rayleigh wave dispersion curve inversion.Both synthetic and in situ fi eld data were used to verify the validity of the proposed method.The results show that the proposed method is superior to the conventional VFSA method in aiming at global minimum,especially when parameter searching space is adjacent to real values of the parameters.The advantage of the new method is that it retains both the merits of VFSA for global search and DLS for local search.At high temperatures,the global search dominates the runs,while at a low temperatures,the local search dominates the runs.Thus,at low temperatures,the proposed method can almost directly approach the actual model.展开更多
The level of deformation development of surrounding rocks is a vital predictor to evaluate impending coal mine disasters and it is important to establish accurate measurements of the deformed status to ensure coal min...The level of deformation development of surrounding rocks is a vital predictor to evaluate impending coal mine disasters and it is important to establish accurate measurements of the deformed status to ensure coal mine safety. Traditional deformation monitoring methods are mostly based on single parameter, in this paper, multiple approaches are integrated: firstly, both electric and elastic models are established,from which electric field distribution and seismic wave recording are calculated and finally, the resistivity profiles and source position information are determined using inversion methods, from which then the deformation and failure of mine floor are evaluated. According to the inversion results of both electric and seismic field signals, multiple-parameter dynamic monitoring of surrounding rock deformation in deep mine can be performed. The methodology is validated using numerical simulation results which shows that the multi-parameter dynamic monitoring methods have better results for surrounding rock deformation in deep mine monitoring than single parameter methods.展开更多
Inverse Synthetic Aperture Radar (ISAR) is an important means for target classification, recognition, identification and many other military applications. A simulation model of ISAR system is established after analyzi...Inverse Synthetic Aperture Radar (ISAR) is an important means for target classification, recognition, identification and many other military applications. A simulation model of ISAR system is established after analyzing the principle of ISAR imaging, and then several ECM (Electronic Counter Measurement) techniques are studied. Simulation experiments are done on the basis of such research. The experimental result of the research can be used for ECM equipment.展开更多
To establish the relationship among reservoir characteristics and rock physical parameters,we construct the well-bore rock physical models firstly,considering the influence factors,such as mineral composition,shale co...To establish the relationship among reservoir characteristics and rock physical parameters,we construct the well-bore rock physical models firstly,considering the influence factors,such as mineral composition,shale content,porosity,fluid type and saturation.Then with analyzing the change rules of elastic parameters along with the above influence factors and the cross-plots among elastic parameters,the sensitive elastic parameters of tight sandstone reservoir are determined,and the rock physics template of sweet spot is constructed to guide pre-stack seismic inversion.The results show that velocity ratio and Poisson impedance are the most sensitive elastic parameters to indicate the lithologic and gas-bearing properties of sweet spot in tight sandstone reservoir.The high-quality sweet spot is characterized by the lower velocity ratio and Poisson impedance.Finally,the actual seismic data are selected to predict the sweet spots in tight sandstone gas reservoirs,so as to verify the validity of the rock physical simulation results.The significant consistency between the relative logging curves and inversion results in different wells implies that the utilization of well-bore rock physical simulation can guide the prediction of sweet spot in tight sandstone gas reservoirs.展开更多
基金Project(9901351) supported by the Hydromechanical Deep Drawing without a Draw DieProject(1057001) supported by the National Natural Science Foundation of China
文摘By using aluminum alloys,the properties of the material in sheet hydroforming were obtained based on the identification of parameters for constitutive models by inverse modeling in which the friction coefficients were also considered in 2D and 3D simulations.With consideration of identified simulation parameters by inverse modeling,some key process parameters including tool dimensions and pre-bulging on the forming processes in sheet hydroforming were investigated and optimized.Based on the optimized parameters,the sheet hydroforming process can be analyzed more accurately to improve the robust design.It proves that the results from simulation based on the identified parameters are in good agreement with those from experiments.
基金supported by National Basic Research Program of China(No.2005CB724105)National Natural Science Foundation of China (No.10477010)National High Technical Research and Development Program of China(No.2007AA04Z141)
文摘Inverse method was used in single crystal superalloy DD6 processing simulation during solidification. Numerical modeling coupled with experiments has been used to estimate the interface heat transfer coefficient （IHTC） between the surface of slab casting and inner mold. Calculated temperature dependent values of IHTC were obtained from a numerical solution. The calculated temperatures agreed well with the measurement of cooling profile.
文摘The maneuvering flight governing equations for coaxial rotor helicopters are established. By introducing induced velocity interference factor analysis, the coaxial rotor aerodynamic interference can be taken into account. With the combination of coaxial rotor helicopter control features and nonlinear inverse solution technique, the governing equations for maneuvering flight can be solved so as to determine helicopter control input, control force and moment, and helicopter body attitudes which are needed for performing the defined maneuver. Finally, as an example of this methods engineering application, the calculated results with level turn, lateral jink maneuvers are presented and simply analyzed.
基金co-supported by the National Natural Science Foundation of China (No. 61503183)the Aeronautical Science Foundation of China (No. 2015ZA52002)
文摘Maneuverability is a key factor to determine whether a helicopter could finish certain flight missions successfully or not. Inverse simulation is commonly used to calculate the pilot controls of a helicopter to complete a certain kind of maneuver flight and to assess its maneuverability.A general method for inverse simulation of maneuver flight for helicopters with the flight control system online is developed in this paper. A general mathematical describing function is established to provide mathematical descriptions of different kinds of maneuvers. A comprehensive control solver based on the optimal linear quadratic regulator theory is developed to calculate the pilot controls of different maneuvers. The coupling problem between pilot controls and flight control system outputs is well solved by taking the flight control system model into the control solver. Inverse simulation of three different kinds of maneuvers with different agility requirements defined in the ADS-33 E-PRF is implemented based on the developed method for a UH-60 helicopter. The results show that the method developed in this paper can solve the closed-loop inverse simulation problem of helicopter maneuver flight with high reliability as well as efficiency.
基金The research results are part of a project carried out in 1999-2002 and financially supported by the US National Foundation(No.ASF EARO125968)in 2001-2003 and financially supported by the National Natural Science Foundation of China(Nos.40271089)the Major Sci-Tech Research Project of the Ministry of Education.
文摘Based on the theory of finite element analysis, an inverse analysis model for the comprehensive medium parameters of the Qinghai-Tibet Plateau is set up. With the help of GPS velocity field, the comprehensive crustal medium parameters of the plateau are inversely analyzed and the characteristics of the related movement macroscopically simulated. It is then concluded that the tectonic deformation of the plateau is mainly in the form of a N-S compression accompanied by an E-W stretching, and the present tectonic setting of the plateau should be the result of the collision between the Indian and the Eurasian continents during the Cenozoic.
文摘The appearance of lower hardness at the surface than at the core after through-hardening of steels is known as "inverse quench-hardening." Pioneering work was performed in the 1970s by establishing a simple test procedure where cylindrical specimens were cooled by air and brine sequentially to produce the effect. This phenomenon was described in relation to the polymer quenching and its effect to the improvement in the fatigue strength of the steel in the 1990s. The hardening mechanism in the same specimens as the pioneering work was recently examined using a finite element simulation method. However, this work has not been completed for lack of experimental quenching cooling curves for the comparisons. In this study, the same experiments using 20mm diameter cylindrical specimens as those of the pioneering work were conducted to obtain cooling curves and hardness distributions for comparing simulated results. Experimental cooling curves showed a temperature recovery as predicted by the simulation. Also the inverse quench-hardening phenomena were found in the measured and simulated hardness distributions of the specimens.
文摘Based on the convection and diffusion mechanisms of radon migration, in this paper we deduce the two-dimensional differential equation for radon transportation in the overburden above active fault zones with an unlimited extension along the strike. Making use of the finite difference method, the radon concentration distribution in the overburden above active faults is calculated and modeled. The active fault zone parameters, such as the depth and the width of the fault zone, and the value of radon concentration, can be inverted from the measured radon concentration curve. These realize quantitative interpretation for radon concentration anomalies. The inversion results are in good agreement with the actual fault zone parameters.
基金The National Natural Science Foundation of China under contract No.40730843the National High Technology Development Program ("863"Program)under contract No.2007AA12Z182
文摘Some missions have been carried out to measure wave directional spectrum by synthetic aperture radar （SAR） and airborne real aperture radar （RAR） at a low incidence.Both them have their own advantages and limitations.Scientists hope that SAR and satellite-based RAR can complement each other for the research on wave properties in the future.For this study,the authors aim to simulate the satellite-based RAR system to validate performance for measuring the directional wave spectrum.The principal measurements are introduced and the simulation methods based on the one developed by Hauser are adopted and slightly modified.To enhance the authenticity of input spectrum and the wave spectrum measuring consistency for SAR and satellite-based RAR,the wave height spectrum inversed from Envisat ASAR data by cross spectrum technology is used as the input spectrum of the simulation system.In the process of simulation,the sea surface,backscattering signal,modulation spectrum and the estimated wave height spectrum are simulated in each look direction.Directional wave spectrum are measured based on the simulated observations from 0 ？ to 360 ？ .From the estimated wave spectrum,it has an 180 ？ ambiguity like SAR,but it has no special high wave number cut off in all the direction.Finally,the estimated spectrum is compared with the input one in terms of the dominant wave wavelength,direction and SWH and the results are promising.The simulation shows that satellite-based RAR should be capable of measuring the directional wave properties.Moreover,it indicates satellite-based RAR basically can measure waves that SAR can measure.
基金financially supported by the State Key Laboratory of Geohazard Prevention and Geoenvironment Protection(Chengdu University of Technology)(Grant No.SKLGP2020Z007)。
文摘Deeply buried mountain tunnels are often exposed to the risk of rock bursts,which always cause serious damage to the supporting structures and threaten the safety of the engineers.Due to the limited data available,a suitable approach to predict the rockburst tendency at the preliminary stage becomes very important.In this study,an integrated methodology combining 3D initial stress inversion and rockburst tendency prediction was developed and subsequently applied to a case study of the Sangzhuling Tunnel on the Sichuan–Tibet Railway.The numerical modelling involved inverting the initial stress field using a multiple linear regression method.The tunnel excavation was simulated separately by FDM and DEM,based on a stress boundary condition from the inverted stress field.The comparative analysis demonstrates that the rockburst ratio calculated using DEM(76.70%)exhibits a slight increase compared to FDM(75.38%),and the rockburst location is consistent with the actual situation.This suggests that DEM is more suitable for simulating the stress redistribution during excavation in a jointed rock mass.The numerical simulation combined with the deviatoric stress approach effectively predicts rockburst tendency,meeting the engineering requirements.Despite its limitations,numerical simulation remains a reliable method for predicting rock bursts.
基金National Key R&D Program of China(No.2017YFB1304000)Fundamental Research Funds for the Central Universities,China(No.2232023G-05-1)。
文摘The high-speed winding spindle employs a flexible support system incorporating rubber O-rings.By precisely configuring the structural parameters and the number of the O-rings,the spindle can stably surpass its critical speed points and maintain operational stability across the entire working speed range.However,the support stiffness and damping of rubber O-rings exhibit significant nonlinear frequency dependence.Conventional experimental methods for deriving equivalent stiffness and damping,based on the principle of the forced non-resonance method,require fabricating custom setups for each O-ring specification and conducting vibration tests at varying frequencies,resulting in low efficiency and high costs.This study proposes a hybrid simulation-experimental method for dynamic parameter identification.Firstly,the frequency-dependent dynamic parameters of a specific O-ring support system are experimentally obtained.Subsequently,a corresponding parametric finite element model is established to simulate and solve the equivalent elastic modulus and equivalent stiffness-damping coefficient of this O-ring support system.Ultimately,after iterative simulation,the simulated and experimental results achieve a 99.7%agreement.The parametric finite element model developed herein can directly simulate and inversely estimate frequency-dependent dynamic parameters for O-rings of different specifications but identical elastic modulus.
文摘Microscopic traffic simulations are useful for solving various trafficrelated problems,e.g.traffic jams and accidents,local and global environmental and energy problems,maintaining mobility in aging societies,and evacuation planning for natural as well as man-made disasters.The origin-destination(OD)matrix is often used as the input to represent traffic demands into traffic simulators.In this study,we propose an indirect method for estimating the OD matrix using a traffic simulator as an internal model.The proposed method is designed to output results that are consistent with the input of the simulator.The method consists of the following steps:(1)calculating link traffic volume from the OD matrix,and(2)updating the matrix.The estimated matrix is updated iteratively until it converges to a predefined tolerance level.Numerical experiments are then conducted using the proposed method on a grid network and on a representation of an actual road network.Finally,we discuss the characteristics of the proposed method and the non-negative constraint for the traffic volume.
基金Foundation item:Supported by the Natural Science Foundation of Hubei Province (2003ABA006 and 2004ABA052.)
文摘A double-walled tubular component can be formed from a metal tube under axial compression by inversion. Numerical simulation and experimental investigation show that die radius is the predominant factor affecting the deformation process. For the given dimensions of 3A21 aluminium alloy tube, the feasible die radius varies between 2-4mm. The deformation process predicted by the finite element simulation agrees with the experiment results well.
文摘Based on the boundary layer data of winter dense fog in 2007 from Nanjing University of Information Science & Technology,the profile characteristics of temperature,wind direction,wind speed and humidity in a dense fog weather on December 13-14 in 2007 were analyzed,as well as their evolution laws in the formation and dispersion of fog,and the boundary layer characteristics of winter dense fog in Nanjing were revealed,while the development of fog was simulated by means of mesoscale numerical model.The results showed that the formation and dispersion of fog was greatly affected by inversion and humidity in the surface layer,and the wind direction in the surface layer also had effect on the formation and dispersion of advection fog.Mesoscale numerical model could preferably simulate the evolution of temperature,humidity,vertical speed in the development of fog,and the simulation of water vapor content in the fog could forecast the formation and dispersion of fog.
基金Projects (11202125, 61175038) supported by the National Natural Science Foundation of China
文摘In order to explore the influence of welding parameters and to investigate the Al alloy (AA) nugget formation process, a comprehensive model involving electrical-thermal-mechanical and metallurgical analysis was established to numerically display the resistance spot welding (RSW) process within multiple fields and understand the AA-RSW physics. A multi-disciplinary finite element method (FEM) framework and a empirical sub-model were built to analyze the affecting factors on weld nugget and the underlying nature of welding physics with dynamic simulation procedure. Specifically, a counter-intuitive phenomenon of the resistance time-variation caused by the transient inverse virtual variation (TIVV) effect was highlighted and analyzed on the basis of welding current and temperature distribution simulation. The empirical model describing the TIVV phenomenon was used for modifying the dynamic resistance simulation during the AA spot welding process. The numerical and experimental results show that the proposed multi-field FEM model agrees with the measured AA welding feature, and the modified dynamic resistance model captures the physics of nugget growth and the electrical-thermal behavior under varying welding current and fluctuating heat input.
基金financially supported by the National Natural Science Foundation of China(Grant Nos.51205346 and 41206074)the National High Technology Research and Development Program of China(863 Program+3 种基金Grant No.2011AA050201)Science Fund for Creative Research Groups of National Natural Science Foundation of China(Grant No.51221004)Zhejiang Provincial Natural Science Foundation of China(Grant No.LY12E05017)Open Foundation of the State Key Laboratory of Fluid Power Transmission and Control(Grant No.GZKF-201311)
文摘This paper describes a dual-stroke acting hydraulic power take-off （PTO） system employed in the wave energy converter （WEC） with an inverse pendulum. The hydraulic PTO converts slow irregular reciprocating wave motions to relatively smooth, fast rotation of an electrical generator. The design of the hydraulic PTO system and its control are critical to maximize the generated power. A time domain simulation study and the laboratory experiment of the full-scale beach test are presented. The results of the simulation and laboratory experiments including their comparison at full-scale are also presented, which have validated the rationality of the design and the reliability of some key components of the prototype of the WEC with an inverse pendulum with the dual-stroke acting hydraulic PTO system.
基金sponsored by the National Natural Science Foundation of China(Grant No.40975004)the State Key Basic Program(973)Program(Grant No.2013CB430100)
文摘The entrainment flux ratio Ae and the inversion layer （IL） thickness are two key parameters in a mixed layer model. Ae is defined as the ratio of the entrainment heat flux at the mixed layer top to the surface heat flux. The IL is the layer between the mixed layer and the free atmosphere. In this study, a parameterization of Ae is derived from the TKE budget in the first- order model for a well-developed CBL under the condition of linearly sheared geostrophic velocity with a zero value at the surface. It is also appropriate for a CBL under the condition of geostrophic velocity remaining constant with height. LESs are conducted under the above two conditions to determine the coefficients in the parameterization scheme. Results suggest that about 43% of the shear-produced TKE in the IL is available for entrainment, while the shear-produced TKE in the mixed layer and surface layer have little effect on entrainment. Based on this scheme, a new scale of convective turbulence velocity is proposed and applied to parameterize the IL thickness, The LES outputs for the CBLs under the condition of linearly sheared geostrophic velocity with a non-zero surface value are used to verify the performance of the parameterization scheme. It is found that the parameterized Ae and IL thickness agree well with the LES outputs.
基金International Science&Technology Cooperation Program of China under Grant No.2011DFA71100the National Key Technology R&D Program under Grant No.2014BAK03B01the National Basic Research Program of China(973 Program)under Grant No.2007CB714201
文摘Surface wave methods are becoming increasingly popular in many geotechnical applications and in earthquake seismology due to their noninvasive characteristics.Inverse surface wave dispersion curves are a crucial step in most surface wave methods.Many inversion methods have been applied to surface wave dispersion curve inversion,including linearized inversion and nonlinearized inversion methods.In this study,a hybrid inversion method of Damped Least Squares(DLS) with Very Fast Simulated Annealing(VFSA) is developed for multi-mode Rayleigh wave dispersion curve inversion.Both synthetic and in situ fi eld data were used to verify the validity of the proposed method.The results show that the proposed method is superior to the conventional VFSA method in aiming at global minimum,especially when parameter searching space is adjacent to real values of the parameters.The advantage of the new method is that it retains both the merits of VFSA for global search and DLS for local search.At high temperatures,the global search dominates the runs,while at a low temperatures,the local search dominates the runs.Thus,at low temperatures,the proposed method can almost directly approach the actual model.
基金financial support from the Fundamental Research Funds for the Central Universities of China (No. 2015QNB19)the financial support from the Open Fund of Key Laboratory of Safety and High-efficiency Coal Mining, Ministry of Education of China (No. JYBSYS2015107)+2 种基金the National Natural Science Foundation of China (Nos. 51404254, 41430317 and U1261202)the China Postdoctoral Science Foundation of China (No. 2014M560465)the Jiangsu Planned Projects for Postdoctoral Research Funds of China (No. 1302050B)
文摘The level of deformation development of surrounding rocks is a vital predictor to evaluate impending coal mine disasters and it is important to establish accurate measurements of the deformed status to ensure coal mine safety. Traditional deformation monitoring methods are mostly based on single parameter, in this paper, multiple approaches are integrated: firstly, both electric and elastic models are established,from which electric field distribution and seismic wave recording are calculated and finally, the resistivity profiles and source position information are determined using inversion methods, from which then the deformation and failure of mine floor are evaluated. According to the inversion results of both electric and seismic field signals, multiple-parameter dynamic monitoring of surrounding rock deformation in deep mine can be performed. The methodology is validated using numerical simulation results which shows that the multi-parameter dynamic monitoring methods have better results for surrounding rock deformation in deep mine monitoring than single parameter methods.
基金Supported by the National Key Lab Project of China(No.51435020203DZ0207)
文摘Inverse Synthetic Aperture Radar (ISAR) is an important means for target classification, recognition, identification and many other military applications. A simulation model of ISAR system is established after analyzing the principle of ISAR imaging, and then several ECM (Electronic Counter Measurement) techniques are studied. Simulation experiments are done on the basis of such research. The experimental result of the research can be used for ECM equipment.
基金supported by the National Key R&D Program of China(Grant No.2018YFC1405900)the Major Projects of National Science and Technology(Grant Nos.2016ZX05011-002,2016ZX05027-002-005)+3 种基金the National Natural Science Foundation of China(Grant No.41806073)the Natural Science Foundation of Shandong Province(Grant No.ZR2017BD014)Shandong Provincial Key Laboratory of Depositional Mineralization and Sedimentary Minerals,Shandong University of Science and Technology(Grant No.DMSM2017042)the Fundamental Research Funds for the Central Universities(Grant No.201964016)
文摘To establish the relationship among reservoir characteristics and rock physical parameters,we construct the well-bore rock physical models firstly,considering the influence factors,such as mineral composition,shale content,porosity,fluid type and saturation.Then with analyzing the change rules of elastic parameters along with the above influence factors and the cross-plots among elastic parameters,the sensitive elastic parameters of tight sandstone reservoir are determined,and the rock physics template of sweet spot is constructed to guide pre-stack seismic inversion.The results show that velocity ratio and Poisson impedance are the most sensitive elastic parameters to indicate the lithologic and gas-bearing properties of sweet spot in tight sandstone reservoir.The high-quality sweet spot is characterized by the lower velocity ratio and Poisson impedance.Finally,the actual seismic data are selected to predict the sweet spots in tight sandstone gas reservoirs,so as to verify the validity of the rock physical simulation results.The significant consistency between the relative logging curves and inversion results in different wells implies that the utilization of well-bore rock physical simulation can guide the prediction of sweet spot in tight sandstone gas reservoirs.
