The fluid of casting process is a typical kind of multi-phase flow. Actually, many casting phenomena have close relationship with the multi-phase flow, such as molten metal filling process, air entrapment, slag moveme...The fluid of casting process is a typical kind of multi-phase flow. Actually, many casting phenomena have close relationship with the multi-phase flow, such as molten metal filling process, air entrapment, slag movement, venting process of die casting, gas escaping of lost foam casting and so on. Obviously, in order to analyze these phenomena accurately, numerical simulation of the multi-phase fluid is necessary. Unfortunately, so far, most of the commercial casting simulation systems do not have the ability of multi-phase flow modeling due to the difficulty in the multi-phase flow calculation. In the paper, Finite Different Method (FDM) technique was adopt to solve the multi-phase fluid model. And a simple object of the muiti-phase fluid was analyzed to obtain the fluid rates of the liquid phase and the entrapped air phase.展开更多
Based on a lattice Boltzmann method and general principles of porous flow, a numerical technique is presented for analysing the separation of multi-phase immiscible fluids in porous media. The total body force acting ...Based on a lattice Boltzmann method and general principles of porous flow, a numerical technique is presented for analysing the separation of multi-phase immiscible fluids in porous media. The total body force acting on fluid particles is modified by axiding relative permeability in Nithiarasu＇s expression with an axiditional surface tension term. As a test of this model, we simulate the phase separation for the case of two immiscible fluids. The numerical results show that the two coupling relative permeability coefficients K12 and K21 have the same magnitude, so the linear flux-forcing relationships satisfy Onsager reciprocity. Phase separation phenomenon is shown with the time evolution of density distribution and bears a strong similarity to the results obtained from other numerical models and the flows in sands. At the same time, the dynamical rules in this model are local, therefore it can be run on massively parallel computers with well computational efficiency.展开更多
A mild gasification process has been implemented to provide an alternative form of clean coal technology called the Integrated Mild Gasification Combined Cycle (IMGCC), which can be utilized to build a new, highly eff...A mild gasification process has been implemented to provide an alternative form of clean coal technology called the Integrated Mild Gasification Combined Cycle (IMGCC), which can be utilized to build a new, highly efficient, and compact power plant or to retrofit an existing coal-fired power plant in order to achieve lower emissions and significantly improved thermal efficiency. The core technology of the mild gasification power plant lies on the design of a compact and effective mild gasifier that can produce synthesis gases with high energy volatiles through a hybrid system: utilizing the features of both entrained-flow and fluidized bed gasifiers. To aid in the design of the mild gasifier, a computational model has been implemented to investigate the thermal-flow and gasification process inside this mild gasifier using the commercial CFD (Computational Fluid Dynamics) solver ANSYS/FLUENT. The Eulerian-Eulerian method is employed to model both the primary phase (air) and the secondary phase (coal particles). However, the Eulerian-Eulerian model used in the software does not facilitate any built-in devolatilization model. The objective of this study is therefore to implement a devolatilization model (along with demoisturization) and incorporate it into the existing code. The Navier-Stokes equations and seven species transport equations are solved with three heterogeneous (gas-solid) and two homogeneous (gas-gas) global gasification reactions. Implementation of the complete model starts from adding demoisturization first, then devolatilization, and then adding one chemical equation at a time until finally all reactions are included in the multiphase flow. The result shows that the demoisturization and devolatilization models are successfully incorporated and a large amount of volatiles are preserved as high-energy fuels in the syngas stream without being further cracked or reacted into lighter gases. The overall results are encouraging but require future experimental data for verification.展开更多
Oil shale is characterized by a dense structure,low proportion of pores and fissures,and low permeability.Pore-fracture systems serve as crucial channels for shale oil migration,directly influencing the production eff...Oil shale is characterized by a dense structure,low proportion of pores and fissures,and low permeability.Pore-fracture systems serve as crucial channels for shale oil migration,directly influencing the production efficiency of shale oil resources.Effectively stimulating oil shale reservoirs remains a challenging and active research topic.This investigation employed shale specimens obtained from the Longmaxi Formation.Scanning electron microscopy,fluid injection experiments,and fluid-structure interaction simulations were used to comprehensively analyze structural changes and fluid flow behavior under high temperatures from microscopic to macroscopic scales.Experimental results indicate that the temperature has little effect on the structure and permeability of shale before 300℃.However,there are two threshold temperatures within the range of 300 to 600℃that have significant effects on the structure and permeability of oil shale.The first threshold temperature is between 300 and 400℃,which causes the oil shale porosity,pore-fracture ratio,and permeability begin to increase.This is manifested by the decrease in micropores and mesopores,the increase in macropores,and the formation of a large number of isolated pores and fissures within the shale.The permeability increases but not significantly.The second threshold temperature is between 500 and 600℃,which increases the permeability of oil shale significantly.During this stage,micropores and mesopores are further reduced,and macropores are significantly enlarged.A large number of connected and penetrated pores and fissures are formed.More numerous and thicker streamlines appear inside the oil shale.The experimental results demonstrate that high temperatures significantly alter the microstructure and permeability of oil shale.At the same time,the experimental results can provide a reference for the research of in-situ heating techniques in oil shale reservoir transformation.展开更多
In oceanic and atmospheric science,finer resolutions have become a prevailing trend in all aspects of development.For high-resolution fluid flow simulations,the computational costs of widely used numerical models incr...In oceanic and atmospheric science,finer resolutions have become a prevailing trend in all aspects of development.For high-resolution fluid flow simulations,the computational costs of widely used numerical models increase significantly with the resolution.Artificial intelligence methods have attracted increasing attention because of their high precision and fast computing speeds compared with traditional numerical model methods.The resolution-independent Fourier neural operator(FNO)presents a promising solution to the still challenging problem of high-resolution fluid flow simulations based on low-resolution data.Accordingly,we assess the potential of FNO for high-resolution fluid flow simulations using the vorticity equation as an example.We assess and compare the performance of FNO in multiple high-resolution tests varying the amounts of data and the evolution durations.When assessed with finer resolution data(even up to number of grid points with 1280×1280),the FNO model,trained at low resolution(number of grid points with 64×64)and with limited data,exhibits a stable overall error and good accuracy.Additionally,our work demonstrates that the FNO model takes less time than the traditional numerical method for high-resolution simulations.This suggests that FNO has the prospect of becoming a cost-effective and highly precise model for high-resolution simulations in the future.Moreover,FNO can make longer high-resolution predictions while training with less data by superimposing vorticity fields from previous time steps as input.A suitable initial learning rate can be set according to the frequency principle,and the time intervals of the dataset need to be adjusted according to the spatial resolution of the input when training the FNO model.Our findings can help optimize FNO for future fluid flow simulations.展开更多
Wavefields in porous media saturated by two immiscible fluids are simulated in this paper.Based on the sealed system theory,the medium model considers both the relative motion between the fluids and the solid skeleton...Wavefields in porous media saturated by two immiscible fluids are simulated in this paper.Based on the sealed system theory,the medium model considers both the relative motion between the fluids and the solid skeleton and the relaxation mechanisms of porosity and saturation（capillary pressure）.So it accurately simulates the numerical attenuation property of the wavefields and is much closer to actual earth media in exploration than the equivalent liquid model and the unsaturated porous medium model on the basis of open system theory.The velocity and attenuation for different wave modes in this medium have been discussed in previous literature but studies of the complete wave-field have not been reported.In our work,wave equations with the relaxation mechanisms of capillary pressure and the porosity are derived.Furthermore,the wavefield and its characteristics are studied using the numerical finite element method.The results show that the slow P3-wave in the non-wetting phase can be observed clearly in the seismic band.The relaxation of capillary pressure and the porosity greatly affect the displacement of the non-wetting phase.More specifically,the displacement decreases with increasing relaxation coefficient.展开更多
In order to improve our understanding of rock fracture and fault instability driven by high-pressure fluid sources, the authors carried out rock fracture tests using granite under a confining pressure of 80 MPa with f...In order to improve our understanding of rock fracture and fault instability driven by high-pressure fluid sources, the authors carried out rock fracture tests using granite under a confining pressure of 80 MPa with fluid injection in the laboratory. Furthermore, we tested a number of numerical models using the FLAC;modeling software to find the best model to represent the experimental results. The high-speed multichannel acoustic emission（AE） waveform recording system used in this study made it possible to examine the total fracture process through detailed monitoring of AE hypocenters and seismic velocity.The experimental results show that injecting high-pressure oil into the rock sample can induce AE activity at very low stress levels and can dramatically reduce the strength of the rock. The results of the numerical simulations show that major experimental results, including the strength, the temporal and spatial patterns of the AE events, and the role of the fluid can be represented fairly well by a model involving（1） randomly distributed defect elements to model pre-existing cracks,（2） random modification of rock properties to represent inhomogeneity introduced by different mineral grains, and（3）macroscopic inhomogeneity. Our study, which incorporates laboratory experiments and numerical simulations, indicates that such an approach is helpful in finding a better model not only for simulating experimental results but also for upscaling purposes.展开更多
Numerical simulation of fluid migration during the ore-forming process of the Carboniferous exhalation- sedimentary (Sedex) massive sulfide deposits in the Tongling district shows that fluid and thermal activities in ...Numerical simulation of fluid migration during the ore-forming process of the Carboniferous exhalation- sedimentary (Sedex) massive sulfide deposits in the Tongling district shows that fluid and thermal activities in lying-wall rocks were limited to a small area around the main draining passage, which led to weak mineralization and alteration in the lying-wall rock. Temperature and fluid fields indicate that mineralization and alteration in the lying-wall rock of the Sedex-type deposits are usually weaker than those of volcano-hosted massive sulfide deposits. Fluid migration involves the following processes: seawater penetrating and leaching the lying-wall rocks, then mixing with ascending hydrothermal fluids in the main draining passage, and finally jetting into seafloor. Although fluid activity-influenced area is rather small, the content of metals leached out from the lying-wall rocks is high enough to form large-scale ore deposits. Tensional contemporaneous faults accompanied with strong heat flows controlled the formation and distribution of Sedex deposits. The tensional tectonic regime on the northern margin of the Yangtze block during the Hercynian provided Sedex deposits with a prerequisite geodynamic condition.展开更多
In modern chemical engineering processes, solid interface involvement is the most important component of process intensification techniques, such as nanoporous membrane separation and heterogeneous catalysis. The fund...In modern chemical engineering processes, solid interface involvement is the most important component of process intensification techniques, such as nanoporous membrane separation and heterogeneous catalysis. The fundamental mechanism underlying interfacial transport remains incompletely understood given the complexity of heterogeneous interfacial molecular interactions and the high nonideality of the fluid involved. Thus, understanding the effects of interface-induced fluid microstructures on flow resistance is the first step in further understanding interfacial transport. Molecular simulation has become an indispensable method for the investigation of fluid microstructure and flow resistance. Here, we reviewed the recent research progress of our group and the latest relevant works to elucidate the contribution of interface-induced fluid microstructures to flow resistance.We specifically focused on water, ionic aqueous solutions, and alcohol–water mixtures given the ubiquity of these fluid systems in modern chemical engineering processes. We discussed the effects of the interfaceinduced hydrogen bond networks of water molecules, the ionic hydration of ionic aqueous solutions, and the spatial distributions of alcohol and alcohol–water mixtures on flow resistance on the basis of the distinctive characteristics of different fluid systems.展开更多
Computational fluid dynamics（CFD） simulations are adopted to investigate rectangular microchannel flows with various periodic micro-structured wall by introducing velocity slip boundary condition at low Reynolds num...Computational fluid dynamics（CFD） simulations are adopted to investigate rectangular microchannel flows with various periodic micro-structured wall by introducing velocity slip boundary condition at low Reynolds number. The purpose of the current study is to numerically find out the effects of periodic micro-structured wall on the flow resistance in rectangular microchannel with the different spacings between microridges ranging from 15 to 60 pm. The simulative results indicate that pressure drop with different spacing between microridges increases linearly with flow velocity and decreases monotonically with slip velocity; Pressure drop reduction also increases with the spacing between microridges at the same condition of slip velocity and flow velocity. The results of numerical simulation are compared with theoretical predictions and experimental results in the literatures. It is found that there is qualitative agreement between them.展开更多
The flow field of gas and liquid in a φ150mm rotating-stream-tray (RST) scrubber is simulated by using computational fluid dynamic (CFD) method. The sismulation is based on the two-equation RNG κ-ε turbulence model...The flow field of gas and liquid in a φ150mm rotating-stream-tray (RST) scrubber is simulated by using computational fluid dynamic (CFD) method. The sismulation is based on the two-equation RNG κ-ε turbulence model, Eulerian multiphase model, and a real-shape 3D model with a huge number of meshes. The simulation results include detailed information about velocity, pressure, volume fraction and so on. Some features of the flow field are obtained: liquid is atomized in a thin annular zone; a high velocity air zone prevents water drops at the bottom from flying towards the wall; the pressure varies sharply at the end of blades and so on. The results will be helpful for structure optimization and engineering design.展开更多
In order to efficiently and realistically capture microscopic features of fluid surface,a fast and stable surface feature simulation approach for particle-based fluids is presented in this paper.This method employs a ...In order to efficiently and realistically capture microscopic features of fluid surface,a fast and stable surface feature simulation approach for particle-based fluids is presented in this paper.This method employs a steady tension and adhesion model to construct surface features with the consideration of the adsorption effect of fluid to solid.Molecular cohesion and surface area minimization are appended for surface tension,and adhesion is added to better show the microscopic characteristics of fluid surface.Besides,the model is integrated to an implicit incompressible smoothed particle hydrodynamics(SPH)method to improve the efficiency and stability of simulation.The experimental results demonstrate that the method can better simulates surface features in a variety of scenarios stably and efficiently.展开更多
To study the airflow distribution in human nasal cavity during respiration and the characteristic parameters of nasal structure, three-dimensional, anatomically accurate representations of 30 adult nasal cavity models...To study the airflow distribution in human nasal cavity during respiration and the characteristic parameters of nasal structure, three-dimensional, anatomically accurate representations of 30 adult nasal cavity models were recons- tructed based on processed tomography images collected from normal people. The airflow fields in nasal cavities were simulated by fluid dynamics with finite element software ANSYS. The results showed that the difference of human nasal cavity structure led to different airflow distribution in the nasal cavities and variation of the main airstream passing through the common nasal meatus. The nasal resistance in the regions of nasal valve and nasal vestibule accounted for more than half of the overall resistance. The characteristic model of nasal cavity was extracted on the basis of characteristic points and dimensions deduced from the original models. It showed that either the geometric structure or the airflow field of the two kinds of models was similar. The characteristic dimensions were the characteristic parameters of nasal cavity that could properly represent the original model in model studies on nasal cavity.展开更多
The metallurgical structure and composition of ingots which depend critically on the fluid motion within the molten pool during the vacuum arc remelting(VAR)process have important effect on the subsequent mechanical p...The metallurgical structure and composition of ingots which depend critically on the fluid motion within the molten pool during the vacuum arc remelting(VAR)process have important effect on the subsequent mechanical processes like forging,rolling and welding.In order to determine the fluid motion of molten pool,a 2D finite element model is established using ANSYS10.0 software,combined with the turbulent fluid flow and heat transfer.The fluid motion caused by thermo buoyancy forces is investigated at different VAR processes in the present study.The results indicate that the fluid flows symmetrically along the axis of the molten pool and clockwisely along the circle at the right pool’s profile.It is also shown that the maximum velocity increases with increasing melting rate and a direct proportional relationship exists.展开更多
For extra-low permeability reservoirs, with a permeability of about 0.3×10?3 μm2, fluid flow and production performance in cores were studied. A long core holder with a multi-location piezometric measurement was...For extra-low permeability reservoirs, with a permeability of about 0.3×10?3 μm2, fluid flow and production performance in cores were studied. A long core holder with a multi-location piezometric measurement was specially designed. An artificial long core, about 700 mm long and with a cross section of 45mm×45mm, was used. In the experiment, pressure distribution along the core can be measured in real time. Single phase flow in the core was investigated. Different modes of production in long cores were also simulated including natural depletion, water flooding, and advanced water flooding. Through physical simulation, flow parameters were collected and production characteristics in extra-low permeability cores were studied. From experimental results, it can be seen that fluid flow in extra-low permeability cores is different from that in high permeability cores. Transmission of pressure in extra-low permeability cores is very slow, and it needs a long time for the pressure to become stable. The distribution curve of pressure along the core is nonlinear and the production rate in extra-low permeability reservoirs decreases sharply. The development effects of different production modes in extra-low permeability cores were compared with one another. Among the production modes, advanced water flooding has much potential for effective development of extra-low permeability reservoirs. Natural depletion and conventional water flooding can also be used in early production periods. In addition, the countermeasures and some ideas especially for the potential development of extra-low permeability reservoirs are suggested.展开更多
The 3-dimensional fluid flow in a water model of the continuous casting tundish is simulated with the k-ε two-equation turbulence model. The methods to decide the size of wall-adjacent grids and the effects of resid...The 3-dimensional fluid flow in a water model of the continuous casting tundish is simulated with the k-ε two-equation turbulence model. The methods to decide the size of wall-adjacent grids and the effects of residuals and mesh size on the simulation accuracy are discussed. The current investigation concludes that the following condition should be satisfied to get accurate enough simulation results: (1) If the dimension of the domain is in the order of cubic meters, the average size of cells in the mesh system should be at least smaller than 30 mm; (2) The normalized non-scaled residual should be reached at least smaller than 10-4.展开更多
The Xiangshan deposit in Jiangxi province is one of the most important uranium deposits in China. The aim of this study is to achieve a better understanding of mineralization in the Xiangshan deposit through numerical...The Xiangshan deposit in Jiangxi province is one of the most important uranium deposits in China. The aim of this study is to achieve a better understanding of mineralization in the Xiangshan deposit through numerical simulation. In order to find the most favorable locations of mineralization and to help further mineral exploration, a coupling deforma- tion and fluid flow model has been established to describe the mineralization process. In this model, the simulation re- constructs the strata deformations under fields of compressive stress and thrust structure on the hanging wall of the Zou-Shi fault. Compared with practical information, the simulation results are consistent with the No. 51 exploration section of the western Xiangshan. In addition, on the basis of geological information provided by previous investigators, the model simulates the flow process of fluids under compressive stress fields. The result suggests that many tensional areas are formed, which can help the fluid flowing upward from deeper parts. The fluid is easy to concentrate on the breccia fractured zone between two volcanic layers, especially on the intersection parts with faults, resulting in the for- mation of favourable locations of mineralization. In addition, the model is significant in guiding the exploration of ura- nium deposits in the western Xiangshan and provides clues for further exploration of deposits.展开更多
By means of the computational fluid dynamics software Fluent 6.3, a mathematical model of three-dimensional three-phase fluid flow field in the molten bath of electric arc furnace （EAF） with side accessorial oxygen ...By means of the computational fluid dynamics software Fluent 6.3, a mathematical model of three-dimensional three-phase fluid flow field in the molten bath of electric arc furnace （EAF） with side accessorial oxygen lances was developed to study the transient phenomena of oxygen jet impingement on the molten steel and the molten slag. The water modeling experiment was carried out to verify the simulation results. The impingement of the supersonic oxygen jet caused impact dent on the molten steel surface accordingly. The area of impact dent changed almost in linear relationship to flow rate of oxygen jet, which can be expressed by a deduced mathematical equation. And the relationship between the impact force of oxygen iet and the correspondingly formed apparent static pressure on molten bath was obtained, which was in linear relationship and a direct proportion, and can also be expressed by a deduced mathematical equation.展开更多
Thin slab casting is used widely in the world. The control of molten steel flow and solidification in the mold is difficult due to the high casting speed and complicated configuration of the mold. Numerical simulation...Thin slab casting is used widely in the world. The control of molten steel flow and solidification in the mold is difficult due to the high casting speed and complicated configuration of the mold. Numerical simulation was carried out to study the fluid flow and heat transfer in the funnel shaped mold. The influence of nozzle design, casting speed and nozzle submersion depth on the flow and temperature fields in the mold was investigated, and guidance for selecting configurations of submerged nozzle was obtained.展开更多
In this work, a two-dimensional fluid model has been employed to study the characteristics of Ar/O2 radio frequency（RF） inductively coupled plasma discharges. The emphasis of this work has been put on the influence ...In this work, a two-dimensional fluid model has been employed to study the characteristics of Ar/O2 radio frequency（RF） inductively coupled plasma discharges. The emphasis of this work has been put on the influence of the external parameters（i.e., the RF power, the pressure, and the Ar/O2 gas ratio） on the plasma properties. The numerical results show that the RF power has a significant influence on the amplitude of the plasma density rather than on the spatial distribution.However, the pressure and the Ar/O2 gas ratio affect not only the amplitude of the plasma density, but also the spatial uniformity. Finally, the comparison between the simulation results and the experimental data has been made at different gas pressures and oxygen contents, and a good agreement has been achieved.展开更多
文摘The fluid of casting process is a typical kind of multi-phase flow. Actually, many casting phenomena have close relationship with the multi-phase flow, such as molten metal filling process, air entrapment, slag movement, venting process of die casting, gas escaping of lost foam casting and so on. Obviously, in order to analyze these phenomena accurately, numerical simulation of the multi-phase fluid is necessary. Unfortunately, so far, most of the commercial casting simulation systems do not have the ability of multi-phase flow modeling due to the difficulty in the multi-phase flow calculation. In the paper, Finite Different Method (FDM) technique was adopt to solve the multi-phase fluid model. And a simple object of the muiti-phase fluid was analyzed to obtain the fluid rates of the liquid phase and the entrapped air phase.
基金Project supported by the National Natural Science Foundation of China （Grant No 10302018）, the Research Grants Council of the Government of the HKSAR, China （Grant No PolyU5172/020）, and the Natural Science Foundation of Zhejiang Province, China （Grant No M103082）.
文摘Based on a lattice Boltzmann method and general principles of porous flow, a numerical technique is presented for analysing the separation of multi-phase immiscible fluids in porous media. The total body force acting on fluid particles is modified by axiding relative permeability in Nithiarasu＇s expression with an axiditional surface tension term. As a test of this model, we simulate the phase separation for the case of two immiscible fluids. The numerical results show that the two coupling relative permeability coefficients K12 and K21 have the same magnitude, so the linear flux-forcing relationships satisfy Onsager reciprocity. Phase separation phenomenon is shown with the time evolution of density distribution and bears a strong similarity to the results obtained from other numerical models and the flows in sands. At the same time, the dynamical rules in this model are local, therefore it can be run on massively parallel computers with well computational efficiency.
文摘A mild gasification process has been implemented to provide an alternative form of clean coal technology called the Integrated Mild Gasification Combined Cycle (IMGCC), which can be utilized to build a new, highly efficient, and compact power plant or to retrofit an existing coal-fired power plant in order to achieve lower emissions and significantly improved thermal efficiency. The core technology of the mild gasification power plant lies on the design of a compact and effective mild gasifier that can produce synthesis gases with high energy volatiles through a hybrid system: utilizing the features of both entrained-flow and fluidized bed gasifiers. To aid in the design of the mild gasifier, a computational model has been implemented to investigate the thermal-flow and gasification process inside this mild gasifier using the commercial CFD (Computational Fluid Dynamics) solver ANSYS/FLUENT. The Eulerian-Eulerian method is employed to model both the primary phase (air) and the secondary phase (coal particles). However, the Eulerian-Eulerian model used in the software does not facilitate any built-in devolatilization model. The objective of this study is therefore to implement a devolatilization model (along with demoisturization) and incorporate it into the existing code. The Navier-Stokes equations and seven species transport equations are solved with three heterogeneous (gas-solid) and two homogeneous (gas-gas) global gasification reactions. Implementation of the complete model starts from adding demoisturization first, then devolatilization, and then adding one chemical equation at a time until finally all reactions are included in the multiphase flow. The result shows that the demoisturization and devolatilization models are successfully incorporated and a large amount of volatiles are preserved as high-energy fuels in the syngas stream without being further cracked or reacted into lighter gases. The overall results are encouraging but require future experimental data for verification.
基金supported by the Chongqing Natural Science Foundation of Chongqing,China(No.CSTB2022NSCQ-MSX0333)the Science and Technology Research Program of Chongqing Municipal Education Commission(Grant No.KJZD-K202401205)+1 种基金Chongqing Three Gorges University Graduate Research and Innovation Project Funding(No.YJSKY24045)Chongqing Engineering Research Center of Disaster Prevention&Control for Banks and Structures in Three Gorges Reservoir Area(No.SXAPGC24YB14,No.SXAPGC24YB03,No.SXAPGC24YB12)。
文摘Oil shale is characterized by a dense structure,low proportion of pores and fissures,and low permeability.Pore-fracture systems serve as crucial channels for shale oil migration,directly influencing the production efficiency of shale oil resources.Effectively stimulating oil shale reservoirs remains a challenging and active research topic.This investigation employed shale specimens obtained from the Longmaxi Formation.Scanning electron microscopy,fluid injection experiments,and fluid-structure interaction simulations were used to comprehensively analyze structural changes and fluid flow behavior under high temperatures from microscopic to macroscopic scales.Experimental results indicate that the temperature has little effect on the structure and permeability of shale before 300℃.However,there are two threshold temperatures within the range of 300 to 600℃that have significant effects on the structure and permeability of oil shale.The first threshold temperature is between 300 and 400℃,which causes the oil shale porosity,pore-fracture ratio,and permeability begin to increase.This is manifested by the decrease in micropores and mesopores,the increase in macropores,and the formation of a large number of isolated pores and fissures within the shale.The permeability increases but not significantly.The second threshold temperature is between 500 and 600℃,which increases the permeability of oil shale significantly.During this stage,micropores and mesopores are further reduced,and macropores are significantly enlarged.A large number of connected and penetrated pores and fissures are formed.More numerous and thicker streamlines appear inside the oil shale.The experimental results demonstrate that high temperatures significantly alter the microstructure and permeability of oil shale.At the same time,the experimental results can provide a reference for the research of in-situ heating techniques in oil shale reservoir transformation.
基金The National Natural Science Foundation of China under contract No.42425606the Basic Scientific Fund for the National Public Research Institute of China(Shu-Xingbei Young Talent Program)under contract No.2023S01+1 种基金the Ocean Decade International Cooperation Center Scientific and Technological Cooperation Project under contract No.GHKJ2024005China-Korea Joint Ocean Research Center Project under contract Nos PI-20240101(China)and 20220407(Korea).
文摘In oceanic and atmospheric science,finer resolutions have become a prevailing trend in all aspects of development.For high-resolution fluid flow simulations,the computational costs of widely used numerical models increase significantly with the resolution.Artificial intelligence methods have attracted increasing attention because of their high precision and fast computing speeds compared with traditional numerical model methods.The resolution-independent Fourier neural operator(FNO)presents a promising solution to the still challenging problem of high-resolution fluid flow simulations based on low-resolution data.Accordingly,we assess the potential of FNO for high-resolution fluid flow simulations using the vorticity equation as an example.We assess and compare the performance of FNO in multiple high-resolution tests varying the amounts of data and the evolution durations.When assessed with finer resolution data(even up to number of grid points with 1280×1280),the FNO model,trained at low resolution(number of grid points with 64×64)and with limited data,exhibits a stable overall error and good accuracy.Additionally,our work demonstrates that the FNO model takes less time than the traditional numerical method for high-resolution simulations.This suggests that FNO has the prospect of becoming a cost-effective and highly precise model for high-resolution simulations in the future.Moreover,FNO can make longer high-resolution predictions while training with less data by superimposing vorticity fields from previous time steps as input.A suitable initial learning rate can be set according to the frequency principle,and the time intervals of the dataset need to be adjusted according to the spatial resolution of the input when training the FNO model.Our findings can help optimize FNO for future fluid flow simulations.
基金supported by the 973 Program (Grant No.2007CB209505)the National Natural Science Foundation of China (Grant No.40674061,40704019)
文摘Wavefields in porous media saturated by two immiscible fluids are simulated in this paper.Based on the sealed system theory,the medium model considers both the relative motion between the fluids and the solid skeleton and the relaxation mechanisms of porosity and saturation（capillary pressure）.So it accurately simulates the numerical attenuation property of the wavefields and is much closer to actual earth media in exploration than the equivalent liquid model and the unsaturated porous medium model on the basis of open system theory.The velocity and attenuation for different wave modes in this medium have been discussed in previous literature but studies of the complete wave-field have not been reported.In our work,wave equations with the relaxation mechanisms of capillary pressure and the porosity are derived.Furthermore,the wavefield and its characteristics are studied using the numerical finite element method.The results show that the slow P3-wave in the non-wetting phase can be observed clearly in the seismic band.The relaxation of capillary pressure and the porosity greatly affect the displacement of the non-wetting phase.More specifically,the displacement decreases with increasing relaxation coefficient.
基金supported by State Key Laboratory of Earthquake Dynamics,China
文摘In order to improve our understanding of rock fracture and fault instability driven by high-pressure fluid sources, the authors carried out rock fracture tests using granite under a confining pressure of 80 MPa with fluid injection in the laboratory. Furthermore, we tested a number of numerical models using the FLAC;modeling software to find the best model to represent the experimental results. The high-speed multichannel acoustic emission（AE） waveform recording system used in this study made it possible to examine the total fracture process through detailed monitoring of AE hypocenters and seismic velocity.The experimental results show that injecting high-pressure oil into the rock sample can induce AE activity at very low stress levels and can dramatically reduce the strength of the rock. The results of the numerical simulations show that major experimental results, including the strength, the temporal and spatial patterns of the AE events, and the role of the fluid can be represented fairly well by a model involving（1） randomly distributed defect elements to model pre-existing cracks,（2） random modification of rock properties to represent inhomogeneity introduced by different mineral grains, and（3）macroscopic inhomogeneity. Our study, which incorporates laboratory experiments and numerical simulations, indicates that such an approach is helpful in finding a better model not only for simulating experimental results but also for upscaling purposes.
基金the National NaturalScience Foundation of China(Project No.40303008 , Key Project No.40234051)the Special Research Project of the Ministry of Land and Resources of China(No.200101030) the 973 Research Project ofthe Ministry of Science and Technology of China(No.2002CB412605).
文摘Numerical simulation of fluid migration during the ore-forming process of the Carboniferous exhalation- sedimentary (Sedex) massive sulfide deposits in the Tongling district shows that fluid and thermal activities in lying-wall rocks were limited to a small area around the main draining passage, which led to weak mineralization and alteration in the lying-wall rock. Temperature and fluid fields indicate that mineralization and alteration in the lying-wall rock of the Sedex-type deposits are usually weaker than those of volcano-hosted massive sulfide deposits. Fluid migration involves the following processes: seawater penetrating and leaching the lying-wall rocks, then mixing with ascending hydrothermal fluids in the main draining passage, and finally jetting into seafloor. Although fluid activity-influenced area is rather small, the content of metals leached out from the lying-wall rocks is high enough to form large-scale ore deposits. Tensional contemporaneous faults accompanied with strong heat flows controlled the formation and distribution of Sedex deposits. The tensional tectonic regime on the northern margin of the Yangtze block during the Hercynian provided Sedex deposits with a prerequisite geodynamic condition.
基金Supported by the National Natural Science Foundation of China(21878144,21576130,21490584 and 21838004)Project of Jiangsu Natural Science Foundation of China(BK20171464)+2 种基金Qing Lan ProjectJiangsu Overseas Visiting Scholar Program for University Prominent Young&Middle-aged Teachers and Presidentsthe Project of Priority Academic Program Development of Jiangsu Higher Education Institutions(PAPD)
文摘In modern chemical engineering processes, solid interface involvement is the most important component of process intensification techniques, such as nanoporous membrane separation and heterogeneous catalysis. The fundamental mechanism underlying interfacial transport remains incompletely understood given the complexity of heterogeneous interfacial molecular interactions and the high nonideality of the fluid involved. Thus, understanding the effects of interface-induced fluid microstructures on flow resistance is the first step in further understanding interfacial transport. Molecular simulation has become an indispensable method for the investigation of fluid microstructure and flow resistance. Here, we reviewed the recent research progress of our group and the latest relevant works to elucidate the contribution of interface-induced fluid microstructures to flow resistance.We specifically focused on water, ionic aqueous solutions, and alcohol–water mixtures given the ubiquity of these fluid systems in modern chemical engineering processes. We discussed the effects of the interfaceinduced hydrogen bond networks of water molecules, the ionic hydration of ionic aqueous solutions, and the spatial distributions of alcohol and alcohol–water mixtures on flow resistance on the basis of the distinctive characteristics of different fluid systems.
基金National Natural Science Foundation of China (No.50435030)
文摘Computational fluid dynamics（CFD） simulations are adopted to investigate rectangular microchannel flows with various periodic micro-structured wall by introducing velocity slip boundary condition at low Reynolds number. The purpose of the current study is to numerically find out the effects of periodic micro-structured wall on the flow resistance in rectangular microchannel with the different spacings between microridges ranging from 15 to 60 pm. The simulative results indicate that pressure drop with different spacing between microridges increases linearly with flow velocity and decreases monotonically with slip velocity; Pressure drop reduction also increases with the spacing between microridges at the same condition of slip velocity and flow velocity. The results of numerical simulation are compared with theoretical predictions and experimental results in the literatures. It is found that there is qualitative agreement between them.
基金Supported by the National 863 Project (2001AA642030-1) and Zhejiang Provincial Key Research Project (010007037).
文摘The flow field of gas and liquid in a φ150mm rotating-stream-tray (RST) scrubber is simulated by using computational fluid dynamic (CFD) method. The sismulation is based on the two-equation RNG κ-ε turbulence model, Eulerian multiphase model, and a real-shape 3D model with a huge number of meshes. The simulation results include detailed information about velocity, pressure, volume fraction and so on. Some features of the flow field are obtained: liquid is atomized in a thin annular zone; a high velocity air zone prevents water drops at the bottom from flying towards the wall; the pressure varies sharply at the end of blades and so on. The results will be helpful for structure optimization and engineering design.
基金Supported by the National Natural Science Foundation of China(61873299,61702036,61572075)Fundamental Research Funds for the Central Universities of China(FRF-TP-17-012A1)China Postdoctoral Science Foundation(2017M620619)
文摘In order to efficiently and realistically capture microscopic features of fluid surface,a fast and stable surface feature simulation approach for particle-based fluids is presented in this paper.This method employs a steady tension and adhesion model to construct surface features with the consideration of the adsorption effect of fluid to solid.Molecular cohesion and surface area minimization are appended for surface tension,and adhesion is added to better show the microscopic characteristics of fluid surface.Besides,the model is integrated to an implicit incompressible smoothed particle hydrodynamics(SPH)method to improve the efficiency and stability of simulation.The experimental results demonstrate that the method can better simulates surface features in a variety of scenarios stably and efficiently.
基金the National Natural Science Foundation of China (1047202510672036)the Natural Science Foundation of Liaoning Province,China (20032109)
文摘To study the airflow distribution in human nasal cavity during respiration and the characteristic parameters of nasal structure, three-dimensional, anatomically accurate representations of 30 adult nasal cavity models were recons- tructed based on processed tomography images collected from normal people. The airflow fields in nasal cavities were simulated by fluid dynamics with finite element software ANSYS. The results showed that the difference of human nasal cavity structure led to different airflow distribution in the nasal cavities and variation of the main airstream passing through the common nasal meatus. The nasal resistance in the regions of nasal valve and nasal vestibule accounted for more than half of the overall resistance. The characteristic model of nasal cavity was extracted on the basis of characteristic points and dimensions deduced from the original models. It showed that either the geometric structure or the airflow field of the two kinds of models was similar. The characteristic dimensions were the characteristic parameters of nasal cavity that could properly represent the original model in model studies on nasal cavity.
基金the National Basic Research Program (973) of China(No.2007CB613802)
文摘The metallurgical structure and composition of ingots which depend critically on the fluid motion within the molten pool during the vacuum arc remelting(VAR)process have important effect on the subsequent mechanical processes like forging,rolling and welding.In order to determine the fluid motion of molten pool,a 2D finite element model is established using ANSYS10.0 software,combined with the turbulent fluid flow and heat transfer.The fluid motion caused by thermo buoyancy forces is investigated at different VAR processes in the present study.The results indicate that the fluid flows symmetrically along the axis of the molten pool and clockwisely along the circle at the right pool’s profile.It is also shown that the maximum velocity increases with increasing melting rate and a direct proportional relationship exists.
基金supported by China National Program on Key Basic Research Project (973 Program) (Grant No. 2006CB705805)National Key Scientific and Technological Project (Grant No. 2008ZX05009-004)
文摘For extra-low permeability reservoirs, with a permeability of about 0.3×10?3 μm2, fluid flow and production performance in cores were studied. A long core holder with a multi-location piezometric measurement was specially designed. An artificial long core, about 700 mm long and with a cross section of 45mm×45mm, was used. In the experiment, pressure distribution along the core can be measured in real time. Single phase flow in the core was investigated. Different modes of production in long cores were also simulated including natural depletion, water flooding, and advanced water flooding. Through physical simulation, flow parameters were collected and production characteristics in extra-low permeability cores were studied. From experimental results, it can be seen that fluid flow in extra-low permeability cores is different from that in high permeability cores. Transmission of pressure in extra-low permeability cores is very slow, and it needs a long time for the pressure to become stable. The distribution curve of pressure along the core is nonlinear and the production rate in extra-low permeability reservoirs decreases sharply. The development effects of different production modes in extra-low permeability cores were compared with one another. Among the production modes, advanced water flooding has much potential for effective development of extra-low permeability reservoirs. Natural depletion and conventional water flooding can also be used in early production periods. In addition, the countermeasures and some ideas especially for the potential development of extra-low permeability reservoirs are suggested.
文摘The 3-dimensional fluid flow in a water model of the continuous casting tundish is simulated with the k-ε two-equation turbulence model. The methods to decide the size of wall-adjacent grids and the effects of residuals and mesh size on the simulation accuracy are discussed. The current investigation concludes that the following condition should be satisfied to get accurate enough simulation results: (1) If the dimension of the domain is in the order of cubic meters, the average size of cells in the mesh system should be at least smaller than 30 mm; (2) The normalized non-scaled residual should be reached at least smaller than 10-4.
基金Projects GPMR0547 supported by the State Key Laboratory of Geological Processes and Mineral Resources, China University of Geosciences, and 2002 CB 412601 by the Chinese Ministry of Science and Technology
文摘The Xiangshan deposit in Jiangxi province is one of the most important uranium deposits in China. The aim of this study is to achieve a better understanding of mineralization in the Xiangshan deposit through numerical simulation. In order to find the most favorable locations of mineralization and to help further mineral exploration, a coupling deforma- tion and fluid flow model has been established to describe the mineralization process. In this model, the simulation re- constructs the strata deformations under fields of compressive stress and thrust structure on the hanging wall of the Zou-Shi fault. Compared with practical information, the simulation results are consistent with the No. 51 exploration section of the western Xiangshan. In addition, on the basis of geological information provided by previous investigators, the model simulates the flow process of fluids under compressive stress fields. The result suggests that many tensional areas are formed, which can help the fluid flowing upward from deeper parts. The fluid is easy to concentrate on the breccia fractured zone between two volcanic layers, especially on the intersection parts with faults, resulting in the for- mation of favourable locations of mineralization. In addition, the model is significant in guiding the exploration of ura- nium deposits in the western Xiangshan and provides clues for further exploration of deposits.
基金Sponsored by National Key Technology Research and Development Program in 11th Five-year Plan of China(2008AF33B01)Fuzhou University Foundation for Development of Science and Technology of China(0020-600588)
文摘By means of the computational fluid dynamics software Fluent 6.3, a mathematical model of three-dimensional three-phase fluid flow field in the molten bath of electric arc furnace （EAF） with side accessorial oxygen lances was developed to study the transient phenomena of oxygen jet impingement on the molten steel and the molten slag. The water modeling experiment was carried out to verify the simulation results. The impingement of the supersonic oxygen jet caused impact dent on the molten steel surface accordingly. The area of impact dent changed almost in linear relationship to flow rate of oxygen jet, which can be expressed by a deduced mathematical equation. And the relationship between the impact force of oxygen iet and the correspondingly formed apparent static pressure on molten bath was obtained, which was in linear relationship and a direct proportion, and can also be expressed by a deduced mathematical equation.
文摘Thin slab casting is used widely in the world. The control of molten steel flow and solidification in the mold is difficult due to the high casting speed and complicated configuration of the mold. Numerical simulation was carried out to study the fluid flow and heat transfer in the funnel shaped mold. The influence of nozzle design, casting speed and nozzle submersion depth on the flow and temperature fields in the mold was investigated, and guidance for selecting configurations of submerged nozzle was obtained.
基金Project supported by the National Science and Technology Major Project of the Ministry of Science and Technology of China(Grant No.2011ZX02403-001)the National Natural Science Foundation of China(Grant No.11205025)
文摘In this work, a two-dimensional fluid model has been employed to study the characteristics of Ar/O2 radio frequency（RF） inductively coupled plasma discharges. The emphasis of this work has been put on the influence of the external parameters（i.e., the RF power, the pressure, and the Ar/O2 gas ratio） on the plasma properties. The numerical results show that the RF power has a significant influence on the amplitude of the plasma density rather than on the spatial distribution.However, the pressure and the Ar/O2 gas ratio affect not only the amplitude of the plasma density, but also the spatial uniformity. Finally, the comparison between the simulation results and the experimental data has been made at different gas pressures and oxygen contents, and a good agreement has been achieved.
