We proposed and demonstrated the ultra-compact 1310/1550 nm wavelength multiplexer/demultiplexer assisted by subwavelength grating(SWG)using particle swarm optimization(PSO)algorithm in silicon-on-insulator(SOI)platfo...We proposed and demonstrated the ultra-compact 1310/1550 nm wavelength multiplexer/demultiplexer assisted by subwavelength grating(SWG)using particle swarm optimization(PSO)algorithm in silicon-on-insulator(SOI)platform.Through the self-imaging effect of multimode interference(MMI)coupler,the demultiplexing function for 1310 nm and 1550 nm wavelengths is implemented.After that,three parallel SWG-based slots are inserted into the MMI section so that the effective refractive index of the modes can be engineered and thus the beat length can be adjusted.Importantly,these three SWG slots significantly reduce the length of the device,which is much shorter than the length of traditional MMI-based wavelength demultiplexers.Ultimately,by using the PSO algorithm,the equivalent refractive index and width of the SWG in a certain range are optimized to achieve the best performance of the wavelength demultiplexer.It has been verified that the device footprint is only 2×30.68μm^(2),and 1 dB bandwidths of larger than 120 nm are acquired at 1310 nm and 1550 nm wavelengths.Meanwhile,the transmitted spectrum shows that the insertion loss(IL)values are below 0.47 dB at both wavelengths when the extinction ratio(ER)values are above 12.65 dB.This inverse design approach has been proved to be efficient in increasing bandwidth and reducing device length.展开更多
Based on the effective structure of the self-mixing interference effects,a general model for the self-mixing interference effects in the LD pumped solid-state laser has been established for the first time.The numerica...Based on the effective structure of the self-mixing interference effects,a general model for the self-mixing interference effects in the LD pumped solid-state laser has been established for the first time.The numerical simulation of the self-mixing interference signal has been done,the results show that when the external cavity length is integral times of 1/2,1/3,2/3,1/4,3/4 of the effective cavity length,the intensity of the self-mixing interference signals reach maximum in value.While that of single mode laser is integral times of half of the effective cavity length,the measuring precision of displacement of single mode laser is λ/2.A conclusion can be drawn from the above results that the measuring precision of displacement of multi-mode laser is higher than that of single mode laser.展开更多
Two-mode converters at 1.3μm, aiming at applications in mode-division multiplexing in Ethernet systems, are proposed and experimentally demonstrated. Based on multimode interference couplers, the two-mode converters ...Two-mode converters at 1.3μm, aiming at applications in mode-division multiplexing in Ethernet systems, are proposed and experimentally demonstrated. Based on multimode interference couplers, the two-mode converters with 50% and 66% mode conversion efficiencies are designed and fabricated on InP substrates. AIode conver- sion from the fundamental mode （TEo） to the first order mode （TE1） is successfully demonstrated within the wavelength range of 1280-1320nm. The 1.3-μm mode converters should be important devices in mode-division multiplexing systems in Ethernet systems.展开更多
An explanation of optical unitary transformation is presented for general nonoverlapping-image multimode interference(MMI)couplers with any number of input and output ports.The light transformation in the MMI coupler ...An explanation of optical unitary transformation is presented for general nonoverlapping-image multimode interference(MMI)couplers with any number of input and output ports.The light transformation in the MMI coupler can be considered as an optical field matrix acting on an input light column vector.We investigate the general phase principle of output light image.The complete proof of nonoverlapping-image MMI coupler’s optical unitarity along with the phase analysis of matrix element is provided.Based on a two-dimensional finite-difference time-domain(2 D-FDTD)simulation,the unitary transformation is obtained for a 4×4 nonoverlapping-image MMI coupler within a deviation of 4×10-2 for orthogonal invariance and 8×10-2 for transvection invariance in the C-band spectral range.A compact 1×4 splitter based on cascaded MMI coupler is proposed,showing a phase deviation less than 5.4°while maintaining a low-loss performance in C-band spectra.展开更多
The temperature dependence of characteristics for multimode interference(MMI) based 3-dB coupler in silicon-on-insulator is analyzed, which originates from the relatively high thermo-optic coefficient of silicon. For ...The temperature dependence of characteristics for multimode interference(MMI) based 3-dB coupler in silicon-on-insulator is analyzed, which originates from the relatively high thermo-optic coefficient of silicon. For restricted interference 3-dB MMI coupler, the output power uniformity is ideally 0 at room temperature and becomes 0.32 dB when temperature rises up to 550 K.For symmetric interference 3-dB MMI coupler, the power uniformity keeps ideally 0 due to its intrinsic symmetric interference mechanism. With the temperature rising, the excess loss of the both devices increases. The performance deterioration due to temperature variety is more obvious to restricted interference MMI 3-dB coupler, comparing with that of symmetric interference MMI 3-dB coupler.展开更多
The muhimode interference （MMI） couplers, which operate at 1. 55 microns in deep rib InGaAsP/InP waveguide with large lateral confinement and tunable power splitting ratios, are of high interest in integrated optics...The muhimode interference （MMI） couplers, which operate at 1. 55 microns in deep rib InGaAsP/InP waveguide with large lateral confinement and tunable power splitting ratios, are of high interest in integrated optics. The gold contacts are applied on the top of waveguides where tuning is desired and the plasma effect will lead to negative refractive index change. The three-dimensional （3D） finite difference beam propagation method（FD-BPM） is used to model the tunable MMI couplers. The length of a 2 × 2 overlap-MMI is determined by FD-BPM, so the longitudinal position of tuning spots is obtained. The position of gold contacts with two types, the edge-pads or center-pad, are also determined. In our design, the length of MMI is 180 microns. If the width of pads is 50 microns and the refractive index is tuned from 0 to -0. 027, the power ratio is tuned from 50 ： 50 to the maximum 88.5 ： 11.4. For deep rib structure, the effective index（EI） method can not be used to simplify the 3D waveguide to plane waveguide because of its lower precision, and so the direct 3D FD-BPM simulation is necessary for the design of 3D MMI couplers.展开更多
An ultracompact 3 dB coupler is designed and fabricated in silicon on insulator,based on 1×2 line tapered multimode interference (MMI) coupler.Comparing with the conventional straight MMI coupler,the device is...An ultracompact 3 dB coupler is designed and fabricated in silicon on insulator,based on 1×2 line tapered multimode interference (MMI) coupler.Comparing with the conventional straight MMI coupler,the device is ～40% shorter in length.The device exhibits uniformity of 1 3dB and excess loss of 2 5dB.展开更多
The integrated quantum interferometer has provided a promising route for manipulating and measuring quantum states of light with high precision,requiring negligible optical loss,broad bandwidth,robust fabrication tole...The integrated quantum interferometer has provided a promising route for manipulating and measuring quantum states of light with high precision,requiring negligible optical loss,broad bandwidth,robust fabrication tolerance,and scalability.展开更多
The design, fabrication and characterization of a fundamental/first-order mode converter based on mul- timode interference coupler on InP substrate were reported. Detailed optimization of the device parameters were in...The design, fabrication and characterization of a fundamental/first-order mode converter based on mul- timode interference coupler on InP substrate were reported. Detailed optimization of the device parameters were investigated using 3D beam propagation method. In the experiments, the fabricated mode converter realized mode conversion from the fundamental mode to the first-order mode in the wavelength range of 1530-1565 nm with ex- cess loss less than 3 dB. Moreover, LPol and LP11 fiber modes were successfully excited from a few-mode fiber by using the device. This InP-based mode converter can be a possible candidate for integrated transceivers for future mode-division multiplexing system.展开更多
In recent years, the silica-on-silicon based multimode interference （MMI） optical waveguide is an interesting research topic. It is being advanced various researches on the silica based MMI coupler. This paper repre...In recent years, the silica-on-silicon based multimode interference （MMI） optical waveguide is an interesting research topic. It is being advanced various researches on the silica based MMI coupler. This paper represents the considerations of the optimal design of the silica-on-silicon based MMI optical coupler for better performance. For that, we have illustrated the simulation results on a particular case of the 4x4 silica-on-silicon based MMI coupler. From the simulation results, it is seen that the performance of the MMI coupler depends on multiple width and length combinations of the MMI waveguide. The results also show that the width of the multimode waveguide could not be too small or too large for optimal performance, and at the widths, 100~tm, 120~tm and 130~tm, the performance could be optimized and be almost 0.62 - 0.64 in a given length range. Finally, the results have been compared with the optical coupler presently available in the market and show that the silica-on-silicon based MMI coupler is much more efficient in terms of losses and the performance associated with it and the size of the coupler.展开更多
A novel integrated dense wavelength division multiplexing interleaver scheme is presented based on phased-array (PHASAR) wavelength demultiplexer with multimode interference (MMI) couplers. MMI-PHASAR interleaver with...A novel integrated dense wavelength division multiplexing interleaver scheme is presented based on phased-array (PHASAR) wavelength demultiplexer with multimode interference (MMI) couplers. MMI-PHASAR interleaver with simple structure and compact si/e can reali/e narrow channel spacing through simple design procedure. And it is convenient for integration with integrated planar waveguide multiplexer/demultiplexers. A 25/50-GHz MMI-PHASAR interleaver is designed and the transmission characteristic is investigated by beasu propagation method.展开更多
A 2 × 2 optical waveguide coupler at 850 nm based on the multimode interference （MMI） structure with the polysilsesquioxanes liquid series （PSQ-Ls） polymer material and the imprint technique is presented. The...A 2 × 2 optical waveguide coupler at 850 nm based on the multimode interference （MMI） structure with the polysilsesquioxanes liquid series （PSQ-Ls） polymer material and the imprint technique is presented. The influence of the structural parameters, such as the single mode condition, the waveguide spacing of input/output ports, and the width and length of the multimode waveguide, on the optical splitting performance including the excess loss and the uniformity is simulated by the beam propagation method. By inserting a taper section of isosceles trapezoid between the single mode and multimode waveguides, the optimized structural parameters for low excess loss and high uniformity are obtained with the excess loss of -0.040 dB and the uniformity of-0.007 dB. The effect of the structure deviations induced during the imprint process on the optical splitting performance at different residual layer thicknesses is also investigated. The analysis results provide useful instructions for the waveguide device fabrication.展开更多
A simple method for improving grating couplers' coupling efficiency without any extra microfabrication processes is proposed. This method can improve the coupling efficiency with 1.69 dB by utilizing the combined ...A simple method for improving grating couplers' coupling efficiency without any extra microfabrication processes is proposed. This method can improve the coupling efficiency with 1.69 dB by utilizing the combined interference in the cladding layer and air gap between the cladding surface and the paralleled angle polished fiber facet. The proposed method can be applied to various kinds of on-chip grating couplers. Back reflection,1 dB bandwidth, and fiber alignment tolerance have also been improved at the same time.展开更多
基金supported by the National Natural Science Foundation of China(No.61505160)the Innovation Capability Support Program of Shaanxi(No.2018KJXX-042)+2 种基金the Natural Science Basic Research Program of Shaanxi(No.2019JM-084)the State Key Laboratory of Transient Optics and Photonics(No.SKLST202108)the Graduate Innovation and Practical Ability Training Project of Xi’an Shiyou University(No.YCS22213190)。
文摘We proposed and demonstrated the ultra-compact 1310/1550 nm wavelength multiplexer/demultiplexer assisted by subwavelength grating(SWG)using particle swarm optimization(PSO)algorithm in silicon-on-insulator(SOI)platform.Through the self-imaging effect of multimode interference(MMI)coupler,the demultiplexing function for 1310 nm and 1550 nm wavelengths is implemented.After that,three parallel SWG-based slots are inserted into the MMI section so that the effective refractive index of the modes can be engineered and thus the beat length can be adjusted.Importantly,these three SWG slots significantly reduce the length of the device,which is much shorter than the length of traditional MMI-based wavelength demultiplexers.Ultimately,by using the PSO algorithm,the equivalent refractive index and width of the SWG in a certain range are optimized to achieve the best performance of the wavelength demultiplexer.It has been verified that the device footprint is only 2×30.68μm^(2),and 1 dB bandwidths of larger than 120 nm are acquired at 1310 nm and 1550 nm wavelengths.Meanwhile,the transmitted spectrum shows that the insertion loss(IL)values are below 0.47 dB at both wavelengths when the extinction ratio(ER)values are above 12.65 dB.This inverse design approach has been proved to be efficient in increasing bandwidth and reducing device length.
文摘Based on the effective structure of the self-mixing interference effects,a general model for the self-mixing interference effects in the LD pumped solid-state laser has been established for the first time.The numerical simulation of the self-mixing interference signal has been done,the results show that when the external cavity length is integral times of 1/2,1/3,2/3,1/4,3/4 of the effective cavity length,the intensity of the self-mixing interference signals reach maximum in value.While that of single mode laser is integral times of half of the effective cavity length,the measuring precision of displacement of single mode laser is λ/2.A conclusion can be drawn from the above results that the measuring precision of displacement of multi-mode laser is higher than that of single mode laser.
基金Supported by the National Basic Research Program of China under Grant No 2014CB340102the National Natural Science Foundation of China under Grant Nos 61474111 and 61274046
文摘Two-mode converters at 1.3μm, aiming at applications in mode-division multiplexing in Ethernet systems, are proposed and experimentally demonstrated. Based on multimode interference couplers, the two-mode converters with 50% and 66% mode conversion efficiencies are designed and fabricated on InP substrates. AIode conver- sion from the fundamental mode （TEo） to the first order mode （TE1） is successfully demonstrated within the wavelength range of 1280-1320nm. The 1.3-μm mode converters should be important devices in mode-division multiplexing systems in Ethernet systems.
基金Project supported by the National Key Research and Development Program of China(Grant No.2018YFB2200202)the National Natural Science Foundation of China(Grant No.61804148)
文摘An explanation of optical unitary transformation is presented for general nonoverlapping-image multimode interference(MMI)couplers with any number of input and output ports.The light transformation in the MMI coupler can be considered as an optical field matrix acting on an input light column vector.We investigate the general phase principle of output light image.The complete proof of nonoverlapping-image MMI coupler’s optical unitarity along with the phase analysis of matrix element is provided.Based on a two-dimensional finite-difference time-domain(2 D-FDTD)simulation,the unitary transformation is obtained for a 4×4 nonoverlapping-image MMI coupler within a deviation of 4×10-2 for orthogonal invariance and 8×10-2 for transvection invariance in the C-band spectral range.A compact 1×4 splitter based on cascaded MMI coupler is proposed,showing a phase deviation less than 5.4°while maintaining a low-loss performance in C-band spectra.
文摘The temperature dependence of characteristics for multimode interference(MMI) based 3-dB coupler in silicon-on-insulator is analyzed, which originates from the relatively high thermo-optic coefficient of silicon. For restricted interference 3-dB MMI coupler, the output power uniformity is ideally 0 at room temperature and becomes 0.32 dB when temperature rises up to 550 K.For symmetric interference 3-dB MMI coupler, the power uniformity keeps ideally 0 due to its intrinsic symmetric interference mechanism. With the temperature rising, the excess loss of the both devices increases. The performance deterioration due to temperature variety is more obvious to restricted interference MMI 3-dB coupler, comparing with that of symmetric interference MMI 3-dB coupler.
文摘The muhimode interference （MMI） couplers, which operate at 1. 55 microns in deep rib InGaAsP/InP waveguide with large lateral confinement and tunable power splitting ratios, are of high interest in integrated optics. The gold contacts are applied on the top of waveguides where tuning is desired and the plasma effect will lead to negative refractive index change. The three-dimensional （3D） finite difference beam propagation method（FD-BPM） is used to model the tunable MMI couplers. The length of a 2 × 2 overlap-MMI is determined by FD-BPM, so the longitudinal position of tuning spots is obtained. The position of gold contacts with two types, the edge-pads or center-pad, are also determined. In our design, the length of MMI is 180 microns. If the width of pads is 50 microns and the refractive index is tuned from 0 to -0. 027, the power ratio is tuned from 50 ： 50 to the maximum 88.5 ： 11.4. For deep rib structure, the effective index（EI） method can not be used to simplify the 3D waveguide to plane waveguide because of its lower precision, and so the direct 3D FD-BPM simulation is necessary for the design of 3D MMI couplers.
文摘An ultracompact 3 dB coupler is designed and fabricated in silicon on insulator,based on 1×2 line tapered multimode interference (MMI) coupler.Comparing with the conventional straight MMI coupler,the device is ～40% shorter in length.The device exhibits uniformity of 1 3dB and excess loss of 2 5dB.
基金National Research Foundation of Korea(2023M3K5A1094805, RS-2024-00343768)National Research Council of Science and Technology (CAP21034-000)+1 种基金Institute for Information and Communications Technology Promotion (2020-0-00972, RS-2024-00396999,RS-2023-00222863)Korea Institute of Science and Technology (KIST) research program (2E33541, 2E33571)
文摘The integrated quantum interferometer has provided a promising route for manipulating and measuring quantum states of light with high precision,requiring negligible optical loss,broad bandwidth,robust fabrication tolerance,and scalability.
基金Project supported by the National Basic Research Program of China(No.2014CB340102)the National Natural Science Foundation of China(Nos.61274045,61335009)
文摘The design, fabrication and characterization of a fundamental/first-order mode converter based on mul- timode interference coupler on InP substrate were reported. Detailed optimization of the device parameters were investigated using 3D beam propagation method. In the experiments, the fabricated mode converter realized mode conversion from the fundamental mode to the first-order mode in the wavelength range of 1530-1565 nm with ex- cess loss less than 3 dB. Moreover, LPol and LP11 fiber modes were successfully excited from a few-mode fiber by using the device. This InP-based mode converter can be a possible candidate for integrated transceivers for future mode-division multiplexing system.
文摘In recent years, the silica-on-silicon based multimode interference （MMI） optical waveguide is an interesting research topic. It is being advanced various researches on the silica based MMI coupler. This paper represents the considerations of the optimal design of the silica-on-silicon based MMI optical coupler for better performance. For that, we have illustrated the simulation results on a particular case of the 4x4 silica-on-silicon based MMI coupler. From the simulation results, it is seen that the performance of the MMI coupler depends on multiple width and length combinations of the MMI waveguide. The results also show that the width of the multimode waveguide could not be too small or too large for optimal performance, and at the widths, 100~tm, 120~tm and 130~tm, the performance could be optimized and be almost 0.62 - 0.64 in a given length range. Finally, the results have been compared with the optical coupler presently available in the market and show that the silica-on-silicon based MMI coupler is much more efficient in terms of losses and the performance associated with it and the size of the coupler.
基金This work was supported by the National Natural Science Foundation of China (No. 69990540).
文摘A novel integrated dense wavelength division multiplexing interleaver scheme is presented based on phased-array (PHASAR) wavelength demultiplexer with multimode interference (MMI) couplers. MMI-PHASAR interleaver with simple structure and compact si/e can reali/e narrow channel spacing through simple design procedure. And it is convenient for integration with integrated planar waveguide multiplexer/demultiplexers. A 25/50-GHz MMI-PHASAR interleaver is designed and the transmission characteristic is investigated by beasu propagation method.
基金This work was supported in part by the International Science ＆ Technology Cooperation Program of China （No. 2014DFG32590）, National Natural Science Foundation of China （No.61077015, 61307040）, National R＆D Program （No.2012AA040406）, Natural Science Foundation of Liaoning Province （No. 2014020002）, Opening Project of Shanghai Key Laboratory of All Solid-state Laser and Applied Techniques （No. 2013ADL04）, and Fundamental Research Funds for the Central Universities （DUT 13JB01, DUT 15ZD231, and DUT2015TD47）.
文摘A 2 × 2 optical waveguide coupler at 850 nm based on the multimode interference （MMI） structure with the polysilsesquioxanes liquid series （PSQ-Ls） polymer material and the imprint technique is presented. The influence of the structural parameters, such as the single mode condition, the waveguide spacing of input/output ports, and the width and length of the multimode waveguide, on the optical splitting performance including the excess loss and the uniformity is simulated by the beam propagation method. By inserting a taper section of isosceles trapezoid between the single mode and multimode waveguides, the optimized structural parameters for low excess loss and high uniformity are obtained with the excess loss of -0.040 dB and the uniformity of-0.007 dB. The effect of the structure deviations induced during the imprint process on the optical splitting performance at different residual layer thicknesses is also investigated. The analysis results provide useful instructions for the waveguide device fabrication.
基金supported by the National Key R&D Program of China (Nos. 2017YFA0303700 and 2017YFA0303704)the National Natural Science Foundation of China (Nos. 61775094 and 41427801)+1 种基金the Fundamental Research Funds for the Central Universities (No. 021314380072), the Priority Academic Program Development of Jiangsu Higher Education Institutions
文摘A simple method for improving grating couplers' coupling efficiency without any extra microfabrication processes is proposed. This method can improve the coupling efficiency with 1.69 dB by utilizing the combined interference in the cladding layer and air gap between the cladding surface and the paralleled angle polished fiber facet. The proposed method can be applied to various kinds of on-chip grating couplers. Back reflection,1 dB bandwidth, and fiber alignment tolerance have also been improved at the same time.
基金the Ministry of Science and Technology "973" Plan ( G2000-03-66)"863" Plan (2002AA312060)the Science Foundation of the Central University for Nationalities(CUN07A)
