Theauthor proposes a dual layer source grid load storage collaborative planning model based on Benders decomposition to optimize the low-carbon and economic performance of the distribution network.The model plans the ...Theauthor proposes a dual layer source grid load storage collaborative planning model based on Benders decomposition to optimize the low-carbon and economic performance of the distribution network.The model plans the configuration of photovoltaic(3.8 MW),wind power(2.5 MW),energy storage(2.2 MWh),and SVC(1.2 Mvar)through interaction between upper and lower layers,and modifies lines 2–3,8–9,etc.to improve transmission capacity and voltage stability.The author uses normal distribution and Monte Carlo method to model load uncertainty,and combines Weibull distribution to describe wind speed characteristics.Compared to the traditional three-layer model(TLM),Benders decomposition-based two-layer model(BLBD)has a 58.1%reduction in convergence time(5.36 vs.12.78 h),a 51.1%reduction in iteration times(23 vs.47 times),a 8.07%reduction in total cost(12.436 vs.13.528 million yuan),and a 9.62%reduction in carbon emissions(12,456 vs.13,782 t).After optimization,the peak valley difference decreased from4.1 to 2.9MW,the renewable energy consumption rate reached 93.4%,and the energy storage efficiency was 87.6%.Themodel has been validated in the IEEE 33 node system,demonstrating its superiority in terms of economy,low-carbon,and reliability.展开更多
Spectrum map construction,which is crucial in cognitive radio(CR)system,visualizes the invisible space of the electromagnetic spectrum for spectrum-resource management and allocation.Traditional reconstruction methods...Spectrum map construction,which is crucial in cognitive radio(CR)system,visualizes the invisible space of the electromagnetic spectrum for spectrum-resource management and allocation.Traditional reconstruction methods are generally for twodimensional(2D)spectrum map and driven by abundant sampling data.In this paper,we propose a data-model-knowledge-driven reconstruction scheme to construct the three-dimensional(3D)spectrum map under multi-radiation source scenarios.We firstly design a maximum and minimum path loss difference(MMPLD)clustering algorithm to detect the number of radiation sources in a 3D space.Then,we develop a joint location-power estimation method based on the heuristic population evolutionary optimization algorithm.Considering the variation of electromagnetic environment,we self-learn the path loss(PL)model based on the sampling data.Finally,the 3D spectrum is reconstructed according to the self-learned PL model and the extracted knowledge of radiation sources.Simulations show that the proposed 3D spectrum map reconstruction scheme not only has splendid adaptability to the environment,but also achieves high spectrum construction accuracy even when the sampling rate is very low.展开更多
A complementary method to determine the vibration source intensity,defined as the weighted vertical acceleration level at the tunnel wall,is needed urgently when comparable measurements or database predictions are una...A complementary method to determine the vibration source intensity,defined as the weighted vertical acceleration level at the tunnel wall,is needed urgently when comparable measurements or database predictions are unavailable in empirical predictions.In this study,we present an analytical model designed to quickly and accurately estimate the vibration source intensity produced by moving metro trains,considering both regular and floating slab tracks.The improved periodic pipe-in-pipe(PiP)model with regular or floating slabs affixed to the tunnel invert was developed.The train loads are represented in the frequency-wavenumber domain to apply in the model.Measured track irregularities were applied and the proposed model was validated against the measured results and verified by a tunnel-soil coupled model.The proposed approach effectively and accurately assessed the vibration source intensity generated by underground trains in a prediction time of just 58 s.Track irregularities significantly affect the vibration source intensity,making them a key factor in comparable measurements or database predictions.A floating slab track can reduce the vibration source intensity by about 14 dB.The proposed approach can serve as an additional method to complement comparable measurements or database predictions for determining the vibration source intensity in empirical predictions.展开更多
The real-time and accurate calculation of electricity indirect carbon emissions is not only the critical component for quantifying the carbon emission levels of the power system but also an effective mean to guide ele...The real-time and accurate calculation of electricity indirect carbon emissions is not only the critical component for quantifying the carbon emission levels of the power system but also an effective mean to guide electricity users in carbon reduction and promote power industry low-carbon transformation.Fundamentally,calculating indirect carbon emissions involves allocating direct carbon emission data from the power source side,indicating that accurate indirect emission results rely on the precise measurement of power source emissions.However,existing research on indirect carbon emissions in large-scale power systems rarely accounts for variations in carbon emission characteristics under different operating conditions of power sources,such as rated/non-rated operating conditions and ramping up/down conditions,making it difficult to reflect source-side and load-side carbon emission information variation during providing ancillary services.Quadratic and exponential functions are proposed to characterize the energy consumption profiles of coal-fired and gas-fired power generation,respectively,to construct a refined carbon emission model for power sources.By leveraging the theory of power system carbon flow,we analyze how variable operating conditions of power sources impact indirect carbon emissions.Case studies demonstrate that changes in power source emissions under variable conditions have a significant effect on the indirect carbon emissions of power grids.展开更多
In the context of large language model(LLM)reshaping software engineering education,this paper presents OSSerCopilot,a LLM-based tutoring system designed to address the critical challenge faced by newcomers(especially...In the context of large language model(LLM)reshaping software engineering education,this paper presents OSSerCopilot,a LLM-based tutoring system designed to address the critical challenge faced by newcomers(especially student contributors)in open source software(OSS)communities.Leveraging natural language processing,code semantic understanding,and learner profiling,the system functions as an intelligent tutor to scaffold three core competency domains:contribution guideline interpretation,project architecture comprehension,and personalized task matching.By transforming traditional onboarding barriers-such as complex contribution documentation and opaque project structures-into interactive learning journeys,OSSerCopilot enables newcomers to complete their first OSS contribution more easily and confidently.This paper highlights how LLM technologies can redefine software engineering education by bridging the gap between theoretical knowledge and practical OSS participation,offering implications for curriculum design,competency assessment,and sustainable OSS ecosystem cultivation.A demonstration video of the system is available at https://figshare.com/articles/media/OSSerCopilot_Introduction_mp4/29510276.展开更多
The equivalent source(ES)method in the spherical coordinate system has been widely applied to processing,reduction,field modeling,and geophysical and geological interpretation of satellite magnetic anomaly data.Howeve...The equivalent source(ES)method in the spherical coordinate system has been widely applied to processing,reduction,field modeling,and geophysical and geological interpretation of satellite magnetic anomaly data.However,the inversion for the ES model suffers from nonuniqueness and instability,which remain unresolved.To mitigate these issues,we introduce both the minimum and flattest models into the model objective function as an alternative regularization approach in the spherical ES method.We first present the methods,then analyze the accuracy of forward calculation and test the proposed ES method in this study by using synthetic data.The experimental results from simulation data indicate that our proposed regularization effectively suppresses the Backus effect and mitigates inversion instability in the low-latitude region.Finally,we apply the proposed method to magnetic anomaly data from China Seismo-Electromagnetic Satellite-1(CSES-1)and Macao Science Satellite-1(MSS-1)magnetic measurements over Africa by constructing an ES model of the large-scale lithospheric magnetic field.Compared with existing global lithospheric magnetic field models,our ES model demonstrates good consistency at high altitudes and predicts more stable fields at low altitudes.Furthermore,we derive the reduction to the pole(RTP)magnetic anomaly fields and the apparent susceptibility contrast distribution based on the ES model.The latter correlates well with the regional tectonic framework in Africa and surroundings.展开更多
Based on the comprehensive analysis of data from petrology and mineralogy,well logging,seismic surveys,paleontology,and geochemistry,a detailed research was conducted on paleoenvironmental and paleoclimatic conditions...Based on the comprehensive analysis of data from petrology and mineralogy,well logging,seismic surveys,paleontology,and geochemistry,a detailed research was conducted on paleoenvironmental and paleoclimatic conditions,and modeling of the source rocks in the second member of the Eocene Wenchang Formation(Wen 2 Member)in the Northern Shunde Subsag at the southwestern margin of the Pearl River Mouth Basin.The Wen 2 Member hosts excellent,thick lacustrine source rocks with strong longitudinal heterogeneity and an average total organic carbon(TOC)content of over 4.9%.The Wen 2 Member can be divided into three units(I,II,III)from bottom to top.Unit I features excellent source rocks with Type I organic matters(average TOC of 5.9%)primarily sourced from lake organisms;Unit II hosts source rocks dominated by Type II2 organic matters(average TOC of 2.2%),which are originated from mixed sources dominated by terrestrial input.Unit III contains good to excellent source rocks dominated by Type II1 organic matters(average TOC of 4.9%),which are mainly contributed by lake organisms and partially by terrestrial input.Under the background of rapid subsidence and limited source supply during intense rifting period in the Eocene,excellent source rocks were developed in Wen 2 Member in the Northern Shunde Subsag under the coordinated control of warm and humid climate,volcanic activity,and deep-water reducing conditions.During the deposition of Unit I,the warm and humid climate and volcanic activity promoted the proliferation of lake algaes,primarily Granodiscus,resulting in high initial productivity,and deep-water reducing conditions enabled satisfactory preservation of organic matters.These factors jointly controlled the development and occurrence of excellent source rocks.During the deposition of Unit II,a transition from warm to cool and semi-arid paleoclimatic conditions led to a decrease in lake algaes and initial productivity.Additionally,enhanced terrestrial input and shallow-water,weakly oxidizing water conditions caused a significant dilution and decomposition of organic matters,degrading the quality of source rocks.During the deposition of Unit III,when the paleoclimatic conditions are cool and humid,Pediastrum and Botryococcus began to thrive,leading to an increase in productivity.Meanwhile,the reducing environment of semi-deep water facilitated the preservation of excellent source rocks,albeit slightly inferior to those in Unit I.The study results clarify the differential origins and development models of various source rocks in the Shunde Sag,offering valuable guidance for evaluating source rocks and selecting petroleum exploration targets in similar marginal sags.展开更多
In the era of AI,especially large models,the importance of open source has become increasingly prominent.First,open source allows innovation to avoid starting from scratch.Through iterative innovation,it promotes tech...In the era of AI,especially large models,the importance of open source has become increasingly prominent.First,open source allows innovation to avoid starting from scratch.Through iterative innovation,it promotes technical exchanges and learning globally.Second,resources required for large model R&D are difficult for a single institution to obtain.The evaluation of general large models also requires the participation of experts from various industries.Third,without open source collaboration,it is difficult to form a unified upper-layer software ecosystem.Therefore,open source has become an important cooperation mechanism to promote the development of AI and large models.There are two cases to illustrate how open source and international standards interact with each other.展开更多
Soils in typical coal industrial areas are often enriched with heavy metals.In the Ningdong industrial park of Northwest China,rapid economic development and pollutant emissions have endangered the surrounding soil en...Soils in typical coal industrial areas are often enriched with heavy metals.In the Ningdong industrial park of Northwest China,rapid economic development and pollutant emissions have endangered the surrounding soil environment.Understanding the spatial distribution,hazards,and sources of heavy metals is crucial to mitigate their contamination in soil.The intense industrial activities in the region lead to complex and diverse origins of heavy metals,making single-source apportionment methods inadequate.In this study,we methodically collected 95 soil samples from a coal-electricity production base in the Ningdong industrial park,and determined the concentrations of Cu,Pb,Cd,Cr,As and Hg.It is found that the concentrations of Cu,Pb,Cd,Cr,As and Hg are 1.29 to 18.45 times higher than the background values.Comprehensive pollution indices indicated that 89.47%of the samples were severely polluted,with Cd and Hg posing the highest ecological risks.Positive Matrix Factorisation and Absolute Principal Component Score-Multiple Linear Regression models identified industrial sources,coal processing,traffic-coal combustion,and mining as primary contributors.Both models yielded similar results,with industrial and coal-related activities being dominant.Heavy metal concentrations were significantly higher in the northwestern and southeastern areas compared to the central region,closely associated with industrial and mining activities.These findings highlight the importance of targeted prevention and management strategies for heavy metal contamination in industrial parks.展开更多
Source rocks(shales) exhibit different geometric pore types and considerable anisotropy caused by the preferential orientation of the clay and kerogen layers,which is not accounted for in classical rockphysics models....Source rocks(shales) exhibit different geometric pore types and considerable anisotropy caused by the preferential orientation of the clay and kerogen layers,which is not accounted for in classical rockphysics models.Pore geometry can be effectively studied through the aspect ratio,and in this study,we use the aspect ratio to characterize different pore geometries.Then,we consider a pore connectivity index as well as a lamination index associated with these orientations.An inclusion-based theory(differential effective medium and self-consistent approximation) and the Brown-Korringa equations are used in the modeling approach.The results show that the indices as well as the aspect ratio of the connected pores significantly affect the elastic properties.We propose an inversion method to invert these three parameters simultaneously from experimental vertical P-and S-wave velocities using a global optimization algorithm.The method is applied to well log and seismic data from the Longmaxi shale reservoir in southwest China to verify its pre dictive ability.展开更多
During 7th-15th October 2023,an earthquake sequence with four MW6.2-6.3 occurred in the Herat region,Afghanistan,causing damage to buildings,fire,and loss of life.The co-seismic deformation induced by the earthquake s...During 7th-15th October 2023,an earthquake sequence with four MW6.2-6.3 occurred in the Herat region,Afghanistan,causing damage to buildings,fire,and loss of life.The co-seismic deformation induced by the earthquake sequence helps us invert the rupture model of these earthquakes to constrain the geometric characteristics of the Herat fault system,and estimate the future seismic risk at this fault system.In this work,we utilized the line-of-sight(LOS)displacements from Interferometric Synthetic Aperture Radar(InSAR)observations to determine the optimal fault geometry and slip distribution of the 2023 Afghanistan earthquake sequence through a two-step inversion method.Our results indicated that these four MW6.2-6.3 earthquakes ruptured the western and northwestern segments of the Herat fault system,which are dominated by thrust motions.We identified two fault models from InSAR LOS displacement data,with two different strikes,and the same dip angle range of about 35-45°.The source model with the strike of 280.5°has a peak slip of about 2.2 m,a central rupture zone with about 25 km along-strike length,and a depth range of 5-10 km,corresponding to a MW6.67 earthquake.The following source model with the strike direction of about 240°has smaller rupture length and width,and a peak slip of about 2.5 m,corresponding to a MW6.65 earthquake.We also calculated the Coulomb Failure Stress of the Herat fault system around this rupture area caused by this earthquake sequence.Our results indicated that the stress loading at the western segment of the Herat Fault system is greater than the triggering threshold,suggesting that the future seismic risk in this area is at a relatively high stage.In summary,the rupture model of these earthquakes indicates that two unidentified thrust faults between the western and northwestern segments of the Herat fault system are in a compression-stress environment.展开更多
The importance of organic geochemistry and basin modeling is widely recognized and used to understand the source rock potential and hydrocarbon generation history of the Mangahewa Formation,and thereby given the found...The importance of organic geochemistry and basin modeling is widely recognized and used to understand the source rock potential and hydrocarbon generation history of the Mangahewa Formation,and thereby given the foundational role in the petroleum exploration.This study utilized the total organic carbon(TOC)content and hydrogen index(HI)to investigate the dominant kerogen type and hydrogen richness for the significance of petroleum generative potential.The Mangahewa coals and carbonaceous shales exhibit an excellent source rocks,with high total organic content(TOC)of more than 22%.The coals and carbonaceous shales were also characterised by Type Ⅱ‒Ⅲ kerogen with Type Ⅲ kerogen,promising oiland gas-prones.The Mangahewa Formation reached the main oil generation,with vitrinite reflectances between 0.53%and 1.01%.Vitrinite reflectance was also used in developing themal models and reveal the transformation(TR)of 10‒50%kerogen to oil during the Late Miocene.The models also showed that the Mangahewa source rock has a significant oil generation and little expulsion competency,with a TR of up to 54%.These findings support the substantial oil-generating potential in the Taranaki Basin's southern graben and can be used as a guide when developing strategies for an oil exploration program.展开更多
Black carbon(BC)aerosol can lead to adverse health effects and drive climate change;therefore,the characteristic research and identification of BC sources are essential for lowering emissions.In this study,equivalent ...Black carbon(BC)aerosol can lead to adverse health effects and drive climate change;therefore,the characteristic research and identification of BC sources are essential for lowering emissions.In this study,equivalent black carbon(eBC)measurement was performed using a seven-wavelength Aethalometer(AE33)at an urban site in a typical industrial city(Zibo)of Northern China for the first time.The monitoring was performed from February 2021 to January 2022.The mass absorption cross-section(MAC)of AE33 was optimised using the online elemental carbon(EC)data,and eBC was corrected using the MAC.The corrected annual BC concentration was 1.72±1.18μg/m^(3).The diurnal variation of BC depicted a bimodal distribution.Furthermore,the BC concentration on weekends was 18%lower than on weekdays.The diurnal variation and weekend effect reflect the critical contributions of traffic emission to BC concentration.The source apportionment of BC was calculated by a constraining Aethalometer model,which restricted theÅngstrom exponent using the online potassium ions.The results revealed that BC was not significantly affected by biomass burning(BC_(bb))in Zibo.The relative contribution of BC_(bb)was higher in winter than in other seasons.The daily morning peak of BC was primarily influenced by traffic sources,whereas the contribution of biomass burning increased after 17:00 in the evening peak.Our findings suggest that it is more important to control fossil fuel sources for BC emission reduction in Zibo,while it is necessary to strengthen the control of biomass combustion sources in winter.展开更多
A new approach to conductive electromagnetic interference （EMI） noise source modeling, i. e. the source internal impedance extraction, is presented. First, the impedance magnitude is achieved through an exciting pro...A new approach to conductive electromagnetic interference （EMI） noise source modeling, i. e. the source internal impedance extraction, is presented. First, the impedance magnitude is achieved through an exciting probe and a detecting probe, or through calculations based on insertion loss measurement results when inserting a series nigh-value known impedance or a shunt low-value known impedance in the circuit. Then the impedance phase is extracted by the Hilbert transform （HT） of the logarithm of the obtained impedance magnitude. Performance studies show that the estimated phase error can increase greatly at a zero frequency in the Hilbert transform because of the existence of a singular point, and this effect can be eliminated by introducing a zero-point when the noise source does not include a series-connected capacitive component. It is also found that when the frequency is nigher than 150 kHz, the estimated phase error is not sensitive to the inductive source but sensitive to the capacitive source. Finally, under the conditions of the same measurement accuracies for impedance magnitude, the accuracy of complex impedance based on the HT can be improved about 10 times when compared with the accuracy of estimated parameters based on the impedance magnitude fitting method （IMFM）.展开更多
This article describes the integrated modeling approach for planning the size and the operation of constructed wetlands for maximizing retention of nonpoint source pollutant loads and reservoir water-quality improveme...This article describes the integrated modeling approach for planning the size and the operation of constructed wetlands for maximizing retention of nonpoint source pollutant loads and reservoir water-quality improvement at a catchment scale. The experimental field-scale wetland systems （four sets, 0.88 ha each） have been in operation since 2002, where water depth was maintained at 30-50 cm and hydraulic loading rate was at 6.3-18.8 cm/day. The wetland system was found to be adequate for treating polluted stream water with stable removal efficiency even during the winter. The integrated modeling system （modified-BASINS） was applied to the Seokmoon estuarine reservoir watershed and calibrated with monitoring data from constructed wetland, stream, and reservoir. The calibrated integrated modeling system estimated that constructing wetlands on 0.5% （about 114 ha） of the watershed area at the mouth of reservoir could reduce 11.61% and 13.49% of total external nitrogen and phosphorus loads, respectively. It also might improve the nitrogen and phosphorus concentration of the reservoir by 9.69% and 16.48%, respectively. The study suggested that about 0.1%-1.0% of the watershed area should be allocated for constructed wetland to meet specified water-quality standards for the estuarine reservoir at the polder area where land use planning is relatively less complicated.展开更多
Individual participation of pollutants in the pollution load should be estimated even if roughly for the appropriate environmental management of a river basin.It is difficult to identify the sources and to quantify th...Individual participation of pollutants in the pollution load should be estimated even if roughly for the appropriate environmental management of a river basin.It is difficult to identify the sources and to quantify the load, especially in modeling nonpoint source.In this study a revised model was established by integrating point and nonpoint sources into one-dimensional Streeter-Phelps(S-P) model on the basis of real-time hydrologic data and surface water quality monitoring data in the Jilin Reach of the Songhua River Basin.Chemical oxygen demand(COD) and ammonia nitrogen(NH 3-N) loads were estimated.Results showed that COD loads of point source and nonpoint source were 134 958 t/yr and 86 209 t/yr, accounting for 61.02% and 38.98% of total loads, respectively.NH 3-N loads of point source and nonpoint source were 16 739 t/yr and 14 272 t/yr, accounting for 53.98% and 46.02%, respectively.Point source pollution was stronger than nonpoint source pollution in the study area at present.The water quality of upstream was better than that of downstream of the rivers and cities.It is indispensable to treat industrial wastewater and municipal sewage out of point sources, to adopt the best management practices to control diffuse pollutants from agricultural land and urban surface runoff in improving water quality of the Songhua River Basin.The revised S-P model can be successfully used to identify pollution source and quantify point source and nonpoint source loads by calibrating and validating.展开更多
Effect of various spatial and energy distributions of fusion neutron sourceon the calculation of neutron wall loading of Tokamak D-D fusion device has been investigated bymeans of the 3-D Monte Carlo code MCNP. A real...Effect of various spatial and energy distributions of fusion neutron sourceon the calculation of neutron wall loading of Tokamak D-D fusion device has been investigated bymeans of the 3-D Monte Carlo code MCNP. A realistic Monte Carlo source model was developed based onthe accurate representation of the spatial distribution and energy spectrum of fusion neutrons tosolve the complicated problem of tokamak fusion neutron source modelling. The results show thatthose simplified source models will introduce significant uncertainties. For accurate estimation ofthe key nuclear responses of the tokamak design and analyses, the use of the realistic source isrecommended. In addition, the accumulation of tritium produced during D-D plasma operation should becarefully considered.展开更多
In order to investigate the hydrocarbon generation process and gas potentials of source rocks in deepwater area of the Qiongdongnan Basin, kinetic parameters of gas generation （activation energy distribution and freq...In order to investigate the hydrocarbon generation process and gas potentials of source rocks in deepwater area of the Qiongdongnan Basin, kinetic parameters of gas generation （activation energy distribution and frequency factor） of the Yacheng Formation source rocks （coal and neritic mudstones） was determined by thermal simulation experiments in the closed system and the specific KINETICS Software. The results show that the activation energy （Ea） distribution of C1–C5 generation ranges from 50 to 74 kcal/mol with a frequency factor of 2.4×1015 s–1 for the neritic mudstone and the Ea distribution of C1–C5 generation ranges from 49 to 73 kcal/mol with a frequency factor of 8.92×1013 s–1 for the coal. On the basis of these kinetic parameters and combined with the data of sedimentary burial and paleothermal histories, the gas generation model of the Yacheng Formation source rocks closer to geological condition was worked out, indicating its main gas generation stage at Ro （vitrinite reflectance） of 1.25%–2.8%. Meanwhile, the gas generation process of the source rocks of different structural locations （central part, southern slope and south low uplift） in the Lingshui Sag was simulated. Among them, the gas generation of the Yacheng Formation source rocks in the central part and the southern slope of the sag entered the main gas window at 10 and 5 Ma respectively and the peak gas generation in the southern slope occurred at 3 Ma. The very late peak gas generation and the relatively large gas potential indices （GPI：20×10^8–60×10^8 m^3/km^2） would provide favorable conditions for the accumulation of large natural gas reserves in the deepwater area.展开更多
The source apportionment of PM2.5 is essential for pollution prevention.In view of the weaknesses of individual models,we proposed an integrated chemical mass balancesource emission inventory(CMB-SEI)model to acquire ...The source apportionment of PM2.5 is essential for pollution prevention.In view of the weaknesses of individual models,we proposed an integrated chemical mass balancesource emission inventory(CMB-SEI)model to acquire more accurate results.First,the SEI of secondary component precursors(SO2,NOx,NH3,and VOCs)was compiled to acquire the emission ratios of these sources for the precursors.Then,a regular CMB simulation was executed to obtain the contributions of primary particle sources and secondary components(SO4^2-,NO3^-3,NH4^+,and SOC).Afterwards,the contributions of secondary components were apportioned into primary sources according to the source emission ratios.The final source apportionment results combined the contributions of primary sources by CMB and SEI.This integrated approach was carried out via a case study of three coastal cities(Zhoushan,Taizhou,and Wenzhou;abbreviated WZ,TZ,and ZS)in Zhejiang Province,China.The regular CMB simulation results showed that PM2.5 pollution was mainly affected by secondary components and mobile sources.The SEI results indicated that electricity,industrial production and mobile sources were the largest contributors to the emission of PM2.5 gaseous precursors.The simulation results of the CMB-SEI model showed that PM2.5 pollution in the coastal areas of Zhejiang Province presented complex pollution characteristics dominated by mobile sources,electricity production sources and industrial production sources.Compared to the results of the CMB and SEI models alone,the CMB-SEI model completely apportioned PM2.5 to primary sources and simultaneously made the results more accurate and reliable in accordance with local industrial characteristics.展开更多
In this paper, we present a magnetocardiogram （MCG） simulation study using the boundary element method （BEM） and based on the virtual heart model and the realistic human volume conductor model. The different contr...In this paper, we present a magnetocardiogram （MCG） simulation study using the boundary element method （BEM） and based on the virtual heart model and the realistic human volume conductor model. The different contributions of cardiac equivalent source models and volume conductor models to the MCG are deeply and comprehensively investigated. The single dipole source model, the multiple dipoles source model and the equivalent double layer （EDL） source model are analysed and compared with the cardiac equivalent source models. Meanwhile, the effect of the volume conductor model on the MCG combined with these cardiac equivalent sources is investigated. The simulation results demonstrate that the cardiac electrophysiological information will be partly missed when only the single dipole source is taken, while the EDL source is a good option for MCG simulation and the effect of the volume conductor is smallest for the EDL source. Therefore, the EDL source is suitable for the study of MCG forward and inverse problems, and more attention should be paid to it in future MCG studies.展开更多
文摘Theauthor proposes a dual layer source grid load storage collaborative planning model based on Benders decomposition to optimize the low-carbon and economic performance of the distribution network.The model plans the configuration of photovoltaic(3.8 MW),wind power(2.5 MW),energy storage(2.2 MWh),and SVC(1.2 Mvar)through interaction between upper and lower layers,and modifies lines 2–3,8–9,etc.to improve transmission capacity and voltage stability.The author uses normal distribution and Monte Carlo method to model load uncertainty,and combines Weibull distribution to describe wind speed characteristics.Compared to the traditional three-layer model(TLM),Benders decomposition-based two-layer model(BLBD)has a 58.1%reduction in convergence time(5.36 vs.12.78 h),a 51.1%reduction in iteration times(23 vs.47 times),a 8.07%reduction in total cost(12.436 vs.13.528 million yuan),and a 9.62%reduction in carbon emissions(12,456 vs.13,782 t).After optimization,the peak valley difference decreased from4.1 to 2.9MW,the renewable energy consumption rate reached 93.4%,and the energy storage efficiency was 87.6%.Themodel has been validated in the IEEE 33 node system,demonstrating its superiority in terms of economy,low-carbon,and reliability.
基金National Key Scientific Instrument and Equipment Development Project under Grant No.61827801the open research fund of State Key Laboratory of Integrated Services Networks,No.ISN22-11+1 种基金Natural Science Foundation of Jiangsu Province,No.BK20211182open research fund of National Mobile Communications Research Laboratory,Southeast University,No.2022D04。
文摘Spectrum map construction,which is crucial in cognitive radio(CR)system,visualizes the invisible space of the electromagnetic spectrum for spectrum-resource management and allocation.Traditional reconstruction methods are generally for twodimensional(2D)spectrum map and driven by abundant sampling data.In this paper,we propose a data-model-knowledge-driven reconstruction scheme to construct the three-dimensional(3D)spectrum map under multi-radiation source scenarios.We firstly design a maximum and minimum path loss difference(MMPLD)clustering algorithm to detect the number of radiation sources in a 3D space.Then,we develop a joint location-power estimation method based on the heuristic population evolutionary optimization algorithm.Considering the variation of electromagnetic environment,we self-learn the path loss(PL)model based on the sampling data.Finally,the 3D spectrum is reconstructed according to the self-learned PL model and the extracted knowledge of radiation sources.Simulations show that the proposed 3D spectrum map reconstruction scheme not only has splendid adaptability to the environment,but also achieves high spectrum construction accuracy even when the sampling rate is very low.
基金supported by the Natural Science Foundation of Shandong Province of China(No.ZR2024QE071).
文摘A complementary method to determine the vibration source intensity,defined as the weighted vertical acceleration level at the tunnel wall,is needed urgently when comparable measurements or database predictions are unavailable in empirical predictions.In this study,we present an analytical model designed to quickly and accurately estimate the vibration source intensity produced by moving metro trains,considering both regular and floating slab tracks.The improved periodic pipe-in-pipe(PiP)model with regular or floating slabs affixed to the tunnel invert was developed.The train loads are represented in the frequency-wavenumber domain to apply in the model.Measured track irregularities were applied and the proposed model was validated against the measured results and verified by a tunnel-soil coupled model.The proposed approach effectively and accurately assessed the vibration source intensity generated by underground trains in a prediction time of just 58 s.Track irregularities significantly affect the vibration source intensity,making them a key factor in comparable measurements or database predictions.A floating slab track can reduce the vibration source intensity by about 14 dB.The proposed approach can serve as an additional method to complement comparable measurements or database predictions for determining the vibration source intensity in empirical predictions.
基金supported by the Science and Technology Project of China Southern Power Grid Co.,Ltd.(ZBKTM20232244)the Project of National Natural of Science Foundation of China(52477103).
文摘The real-time and accurate calculation of electricity indirect carbon emissions is not only the critical component for quantifying the carbon emission levels of the power system but also an effective mean to guide electricity users in carbon reduction and promote power industry low-carbon transformation.Fundamentally,calculating indirect carbon emissions involves allocating direct carbon emission data from the power source side,indicating that accurate indirect emission results rely on the precise measurement of power source emissions.However,existing research on indirect carbon emissions in large-scale power systems rarely accounts for variations in carbon emission characteristics under different operating conditions of power sources,such as rated/non-rated operating conditions and ramping up/down conditions,making it difficult to reflect source-side and load-side carbon emission information variation during providing ancillary services.Quadratic and exponential functions are proposed to characterize the energy consumption profiles of coal-fired and gas-fired power generation,respectively,to construct a refined carbon emission model for power sources.By leveraging the theory of power system carbon flow,we analyze how variable operating conditions of power sources impact indirect carbon emissions.Case studies demonstrate that changes in power source emissions under variable conditions have a significant effect on the indirect carbon emissions of power grids.
基金supported by the National Natural Science Foundation of China (62202022, 92582204, and 62572030)the Fundamental Research Funds for the Central Universitiesthe exploratory elective projects of the State Key Laboratory of Complex and Critical Software Environments
文摘In the context of large language model(LLM)reshaping software engineering education,this paper presents OSSerCopilot,a LLM-based tutoring system designed to address the critical challenge faced by newcomers(especially student contributors)in open source software(OSS)communities.Leveraging natural language processing,code semantic understanding,and learner profiling,the system functions as an intelligent tutor to scaffold three core competency domains:contribution guideline interpretation,project architecture comprehension,and personalized task matching.By transforming traditional onboarding barriers-such as complex contribution documentation and opaque project structures-into interactive learning journeys,OSSerCopilot enables newcomers to complete their first OSS contribution more easily and confidently.This paper highlights how LLM technologies can redefine software engineering education by bridging the gap between theoretical knowledge and practical OSS participation,offering implications for curriculum design,competency assessment,and sustainable OSS ecosystem cultivation.A demonstration video of the system is available at https://figshare.com/articles/media/OSSerCopilot_Introduction_mp4/29510276.
基金supported by the National Natural Science Foundation of China(Grant Nos.42250103 and 42174090)the Opening Fund of Key Laboratory of Geological Survey and Evaluation of Ministry of Education(Grant No.GLAB2023ZR02)the MOST Special Fund from the State Key Laboratory of Geological Processes and Mineral Resources(Grant No.MSFGPMR2022-4).
文摘The equivalent source(ES)method in the spherical coordinate system has been widely applied to processing,reduction,field modeling,and geophysical and geological interpretation of satellite magnetic anomaly data.However,the inversion for the ES model suffers from nonuniqueness and instability,which remain unresolved.To mitigate these issues,we introduce both the minimum and flattest models into the model objective function as an alternative regularization approach in the spherical ES method.We first present the methods,then analyze the accuracy of forward calculation and test the proposed ES method in this study by using synthetic data.The experimental results from simulation data indicate that our proposed regularization effectively suppresses the Backus effect and mitigates inversion instability in the low-latitude region.Finally,we apply the proposed method to magnetic anomaly data from China Seismo-Electromagnetic Satellite-1(CSES-1)and Macao Science Satellite-1(MSS-1)magnetic measurements over Africa by constructing an ES model of the large-scale lithospheric magnetic field.Compared with existing global lithospheric magnetic field models,our ES model demonstrates good consistency at high altitudes and predicts more stable fields at low altitudes.Furthermore,we derive the reduction to the pole(RTP)magnetic anomaly fields and the apparent susceptibility contrast distribution based on the ES model.The latter correlates well with the regional tectonic framework in Africa and surroundings.
基金Supported by the Research Project of China National Offshore Oil Corporation(SCKY-2023-HN-3)。
文摘Based on the comprehensive analysis of data from petrology and mineralogy,well logging,seismic surveys,paleontology,and geochemistry,a detailed research was conducted on paleoenvironmental and paleoclimatic conditions,and modeling of the source rocks in the second member of the Eocene Wenchang Formation(Wen 2 Member)in the Northern Shunde Subsag at the southwestern margin of the Pearl River Mouth Basin.The Wen 2 Member hosts excellent,thick lacustrine source rocks with strong longitudinal heterogeneity and an average total organic carbon(TOC)content of over 4.9%.The Wen 2 Member can be divided into three units(I,II,III)from bottom to top.Unit I features excellent source rocks with Type I organic matters(average TOC of 5.9%)primarily sourced from lake organisms;Unit II hosts source rocks dominated by Type II2 organic matters(average TOC of 2.2%),which are originated from mixed sources dominated by terrestrial input.Unit III contains good to excellent source rocks dominated by Type II1 organic matters(average TOC of 4.9%),which are mainly contributed by lake organisms and partially by terrestrial input.Under the background of rapid subsidence and limited source supply during intense rifting period in the Eocene,excellent source rocks were developed in Wen 2 Member in the Northern Shunde Subsag under the coordinated control of warm and humid climate,volcanic activity,and deep-water reducing conditions.During the deposition of Unit I,the warm and humid climate and volcanic activity promoted the proliferation of lake algaes,primarily Granodiscus,resulting in high initial productivity,and deep-water reducing conditions enabled satisfactory preservation of organic matters.These factors jointly controlled the development and occurrence of excellent source rocks.During the deposition of Unit II,a transition from warm to cool and semi-arid paleoclimatic conditions led to a decrease in lake algaes and initial productivity.Additionally,enhanced terrestrial input and shallow-water,weakly oxidizing water conditions caused a significant dilution and decomposition of organic matters,degrading the quality of source rocks.During the deposition of Unit III,when the paleoclimatic conditions are cool and humid,Pediastrum and Botryococcus began to thrive,leading to an increase in productivity.Meanwhile,the reducing environment of semi-deep water facilitated the preservation of excellent source rocks,albeit slightly inferior to those in Unit I.The study results clarify the differential origins and development models of various source rocks in the Shunde Sag,offering valuable guidance for evaluating source rocks and selecting petroleum exploration targets in similar marginal sags.
文摘In the era of AI,especially large models,the importance of open source has become increasingly prominent.First,open source allows innovation to avoid starting from scratch.Through iterative innovation,it promotes technical exchanges and learning globally.Second,resources required for large model R&D are difficult for a single institution to obtain.The evaluation of general large models also requires the participation of experts from various industries.Third,without open source collaboration,it is difficult to form a unified upper-layer software ecosystem.Therefore,open source has become an important cooperation mechanism to promote the development of AI and large models.There are two cases to illustrate how open source and international standards interact with each other.
基金funded by the National Natural Science Foundation of China(NSFC)(32360321)the Ningxia Key Research and Development Project(2024BEG02007)the Natural Science Foundation of Ningxia Hui Autonomous Region Project(2023AAC03046,2023AAC02018).
文摘Soils in typical coal industrial areas are often enriched with heavy metals.In the Ningdong industrial park of Northwest China,rapid economic development and pollutant emissions have endangered the surrounding soil environment.Understanding the spatial distribution,hazards,and sources of heavy metals is crucial to mitigate their contamination in soil.The intense industrial activities in the region lead to complex and diverse origins of heavy metals,making single-source apportionment methods inadequate.In this study,we methodically collected 95 soil samples from a coal-electricity production base in the Ningdong industrial park,and determined the concentrations of Cu,Pb,Cd,Cr,As and Hg.It is found that the concentrations of Cu,Pb,Cd,Cr,As and Hg are 1.29 to 18.45 times higher than the background values.Comprehensive pollution indices indicated that 89.47%of the samples were severely polluted,with Cd and Hg posing the highest ecological risks.Positive Matrix Factorisation and Absolute Principal Component Score-Multiple Linear Regression models identified industrial sources,coal processing,traffic-coal combustion,and mining as primary contributors.Both models yielded similar results,with industrial and coal-related activities being dominant.Heavy metal concentrations were significantly higher in the northwestern and southeastern areas compared to the central region,closely associated with industrial and mining activities.These findings highlight the importance of targeted prevention and management strategies for heavy metal contamination in industrial parks.
基金funded by the National Natural Science Foundation of China (No. 42374128)by the Fundamental Research Funds for the Central Universities (No. B240201110)。
文摘Source rocks(shales) exhibit different geometric pore types and considerable anisotropy caused by the preferential orientation of the clay and kerogen layers,which is not accounted for in classical rockphysics models.Pore geometry can be effectively studied through the aspect ratio,and in this study,we use the aspect ratio to characterize different pore geometries.Then,we consider a pore connectivity index as well as a lamination index associated with these orientations.An inclusion-based theory(differential effective medium and self-consistent approximation) and the Brown-Korringa equations are used in the modeling approach.The results show that the indices as well as the aspect ratio of the connected pores significantly affect the elastic properties.We propose an inversion method to invert these three parameters simultaneously from experimental vertical P-and S-wave velocities using a global optimization algorithm.The method is applied to well log and seismic data from the Longmaxi shale reservoir in southwest China to verify its pre dictive ability.
基金funded by the PhD Starting Research Fund in East China Jiaotong University,Grant No.2003423017the National Natural Science Foundation of China(Grant Nos.42304009)。
文摘During 7th-15th October 2023,an earthquake sequence with four MW6.2-6.3 occurred in the Herat region,Afghanistan,causing damage to buildings,fire,and loss of life.The co-seismic deformation induced by the earthquake sequence helps us invert the rupture model of these earthquakes to constrain the geometric characteristics of the Herat fault system,and estimate the future seismic risk at this fault system.In this work,we utilized the line-of-sight(LOS)displacements from Interferometric Synthetic Aperture Radar(InSAR)observations to determine the optimal fault geometry and slip distribution of the 2023 Afghanistan earthquake sequence through a two-step inversion method.Our results indicated that these four MW6.2-6.3 earthquakes ruptured the western and northwestern segments of the Herat fault system,which are dominated by thrust motions.We identified two fault models from InSAR LOS displacement data,with two different strikes,and the same dip angle range of about 35-45°.The source model with the strike of 280.5°has a peak slip of about 2.2 m,a central rupture zone with about 25 km along-strike length,and a depth range of 5-10 km,corresponding to a MW6.67 earthquake.The following source model with the strike direction of about 240°has smaller rupture length and width,and a peak slip of about 2.5 m,corresponding to a MW6.65 earthquake.We also calculated the Coulomb Failure Stress of the Herat fault system around this rupture area caused by this earthquake sequence.Our results indicated that the stress loading at the western segment of the Herat Fault system is greater than the triggering threshold,suggesting that the future seismic risk in this area is at a relatively high stage.In summary,the rupture model of these earthquakes indicates that two unidentified thrust faults between the western and northwestern segments of the Herat fault system are in a compression-stress environment.
基金Supporting Project number(RSP2025R92)at King Saud University,Riyadh,Saudi Arabia,for their support.
文摘The importance of organic geochemistry and basin modeling is widely recognized and used to understand the source rock potential and hydrocarbon generation history of the Mangahewa Formation,and thereby given the foundational role in the petroleum exploration.This study utilized the total organic carbon(TOC)content and hydrogen index(HI)to investigate the dominant kerogen type and hydrogen richness for the significance of petroleum generative potential.The Mangahewa coals and carbonaceous shales exhibit an excellent source rocks,with high total organic content(TOC)of more than 22%.The coals and carbonaceous shales were also characterised by Type Ⅱ‒Ⅲ kerogen with Type Ⅲ kerogen,promising oiland gas-prones.The Mangahewa Formation reached the main oil generation,with vitrinite reflectances between 0.53%and 1.01%.Vitrinite reflectance was also used in developing themal models and reveal the transformation(TR)of 10‒50%kerogen to oil during the Late Miocene.The models also showed that the Mangahewa source rock has a significant oil generation and little expulsion competency,with a TR of up to 54%.These findings support the substantial oil-generating potential in the Taranaki Basin's southern graben and can be used as a guide when developing strategies for an oil exploration program.
基金supported by the National Key Research and Development Program of China(Nos.2017YFC0212501 and 2017YFC0212503).
文摘Black carbon(BC)aerosol can lead to adverse health effects and drive climate change;therefore,the characteristic research and identification of BC sources are essential for lowering emissions.In this study,equivalent black carbon(eBC)measurement was performed using a seven-wavelength Aethalometer(AE33)at an urban site in a typical industrial city(Zibo)of Northern China for the first time.The monitoring was performed from February 2021 to January 2022.The mass absorption cross-section(MAC)of AE33 was optimised using the online elemental carbon(EC)data,and eBC was corrected using the MAC.The corrected annual BC concentration was 1.72±1.18μg/m^(3).The diurnal variation of BC depicted a bimodal distribution.Furthermore,the BC concentration on weekends was 18%lower than on weekdays.The diurnal variation and weekend effect reflect the critical contributions of traffic emission to BC concentration.The source apportionment of BC was calculated by a constraining Aethalometer model,which restricted theÅngstrom exponent using the online potassium ions.The results revealed that BC was not significantly affected by biomass burning(BC_(bb))in Zibo.The relative contribution of BC_(bb)was higher in winter than in other seasons.The daily morning peak of BC was primarily influenced by traffic sources,whereas the contribution of biomass burning increased after 17:00 in the evening peak.Our findings suggest that it is more important to control fossil fuel sources for BC emission reduction in Zibo,while it is necessary to strengthen the control of biomass combustion sources in winter.
基金The Natural Science Foundation of Jiangsu Province(No.BK2008429)Open Research Foundation of State Key Laboratory of Millimeter Waves of Southeast University(No.K200603)+1 种基金China Postdoctoral Science Foundation(No.20080431126)Jiangsu Postdoctoral Science Foundation(No.2007-337)
文摘A new approach to conductive electromagnetic interference （EMI） noise source modeling, i. e. the source internal impedance extraction, is presented. First, the impedance magnitude is achieved through an exciting probe and a detecting probe, or through calculations based on insertion loss measurement results when inserting a series nigh-value known impedance or a shunt low-value known impedance in the circuit. Then the impedance phase is extracted by the Hilbert transform （HT） of the logarithm of the obtained impedance magnitude. Performance studies show that the estimated phase error can increase greatly at a zero frequency in the Hilbert transform because of the existence of a singular point, and this effect can be eliminated by introducing a zero-point when the noise source does not include a series-connected capacitive component. It is also found that when the frequency is nigher than 150 kHz, the estimated phase error is not sensitive to the inductive source but sensitive to the capacitive source. Finally, under the conditions of the same measurement accuracies for impedance magnitude, the accuracy of complex impedance based on the HT can be improved about 10 times when compared with the accuracy of estimated parameters based on the impedance magnitude fitting method （IMFM）.
文摘This article describes the integrated modeling approach for planning the size and the operation of constructed wetlands for maximizing retention of nonpoint source pollutant loads and reservoir water-quality improvement at a catchment scale. The experimental field-scale wetland systems （four sets, 0.88 ha each） have been in operation since 2002, where water depth was maintained at 30-50 cm and hydraulic loading rate was at 6.3-18.8 cm/day. The wetland system was found to be adequate for treating polluted stream water with stable removal efficiency even during the winter. The integrated modeling system （modified-BASINS） was applied to the Seokmoon estuarine reservoir watershed and calibrated with monitoring data from constructed wetland, stream, and reservoir. The calibrated integrated modeling system estimated that constructing wetlands on 0.5% （about 114 ha） of the watershed area at the mouth of reservoir could reduce 11.61% and 13.49% of total external nitrogen and phosphorus loads, respectively. It also might improve the nitrogen and phosphorus concentration of the reservoir by 9.69% and 16.48%, respectively. The study suggested that about 0.1%-1.0% of the watershed area should be allocated for constructed wetland to meet specified water-quality standards for the estuarine reservoir at the polder area where land use planning is relatively less complicated.
基金Under the auspices of Major State Basic Research Development Program of China (973 Program) (No. 2004CB418502,No. 2007CB407205)the Knowledge Innovation Programs of Chinese Academy of Sciences (No. KSCX1-YW-09-13)
文摘Individual participation of pollutants in the pollution load should be estimated even if roughly for the appropriate environmental management of a river basin.It is difficult to identify the sources and to quantify the load, especially in modeling nonpoint source.In this study a revised model was established by integrating point and nonpoint sources into one-dimensional Streeter-Phelps(S-P) model on the basis of real-time hydrologic data and surface water quality monitoring data in the Jilin Reach of the Songhua River Basin.Chemical oxygen demand(COD) and ammonia nitrogen(NH 3-N) loads were estimated.Results showed that COD loads of point source and nonpoint source were 134 958 t/yr and 86 209 t/yr, accounting for 61.02% and 38.98% of total loads, respectively.NH 3-N loads of point source and nonpoint source were 16 739 t/yr and 14 272 t/yr, accounting for 53.98% and 46.02%, respectively.Point source pollution was stronger than nonpoint source pollution in the study area at present.The water quality of upstream was better than that of downstream of the rivers and cities.It is indispensable to treat industrial wastewater and municipal sewage out of point sources, to adopt the best management practices to control diffuse pollutants from agricultural land and urban surface runoff in improving water quality of the Songhua River Basin.The revised S-P model can be successfully used to identify pollution source and quantify point source and nonpoint source loads by calibrating and validating.
基金The project supported partly by the National Science Foundation of Anhui Province (No. 0104360)
文摘Effect of various spatial and energy distributions of fusion neutron sourceon the calculation of neutron wall loading of Tokamak D-D fusion device has been investigated bymeans of the 3-D Monte Carlo code MCNP. A realistic Monte Carlo source model was developed based onthe accurate representation of the spatial distribution and energy spectrum of fusion neutrons tosolve the complicated problem of tokamak fusion neutron source modelling. The results show thatthose simplified source models will introduce significant uncertainties. For accurate estimation ofthe key nuclear responses of the tokamak design and analyses, the use of the realistic source isrecommended. In addition, the accumulation of tritium produced during D-D plasma operation should becarefully considered.
基金The National Science and Technology Major Project of China under contract No.2011ZX05025-002
文摘In order to investigate the hydrocarbon generation process and gas potentials of source rocks in deepwater area of the Qiongdongnan Basin, kinetic parameters of gas generation （activation energy distribution and frequency factor） of the Yacheng Formation source rocks （coal and neritic mudstones） was determined by thermal simulation experiments in the closed system and the specific KINETICS Software. The results show that the activation energy （Ea） distribution of C1–C5 generation ranges from 50 to 74 kcal/mol with a frequency factor of 2.4×1015 s–1 for the neritic mudstone and the Ea distribution of C1–C5 generation ranges from 49 to 73 kcal/mol with a frequency factor of 8.92×1013 s–1 for the coal. On the basis of these kinetic parameters and combined with the data of sedimentary burial and paleothermal histories, the gas generation model of the Yacheng Formation source rocks closer to geological condition was worked out, indicating its main gas generation stage at Ro （vitrinite reflectance） of 1.25%–2.8%. Meanwhile, the gas generation process of the source rocks of different structural locations （central part, southern slope and south low uplift） in the Lingshui Sag was simulated. Among them, the gas generation of the Yacheng Formation source rocks in the central part and the southern slope of the sag entered the main gas window at 10 and 5 Ma respectively and the peak gas generation in the southern slope occurred at 3 Ma. The very late peak gas generation and the relatively large gas potential indices （GPI：20×10^8–60×10^8 m^3/km^2） would provide favorable conditions for the accumulation of large natural gas reserves in the deepwater area.
基金supported by the National Key Research and Development Program of China(No.2018YFC0214102)。
文摘The source apportionment of PM2.5 is essential for pollution prevention.In view of the weaknesses of individual models,we proposed an integrated chemical mass balancesource emission inventory(CMB-SEI)model to acquire more accurate results.First,the SEI of secondary component precursors(SO2,NOx,NH3,and VOCs)was compiled to acquire the emission ratios of these sources for the precursors.Then,a regular CMB simulation was executed to obtain the contributions of primary particle sources and secondary components(SO4^2-,NO3^-3,NH4^+,and SOC).Afterwards,the contributions of secondary components were apportioned into primary sources according to the source emission ratios.The final source apportionment results combined the contributions of primary sources by CMB and SEI.This integrated approach was carried out via a case study of three coastal cities(Zhoushan,Taizhou,and Wenzhou;abbreviated WZ,TZ,and ZS)in Zhejiang Province,China.The regular CMB simulation results showed that PM2.5 pollution was mainly affected by secondary components and mobile sources.The SEI results indicated that electricity,industrial production and mobile sources were the largest contributors to the emission of PM2.5 gaseous precursors.The simulation results of the CMB-SEI model showed that PM2.5 pollution in the coastal areas of Zhejiang Province presented complex pollution characteristics dominated by mobile sources,electricity production sources and industrial production sources.Compared to the results of the CMB and SEI models alone,the CMB-SEI model completely apportioned PM2.5 to primary sources and simultaneously made the results more accurate and reliable in accordance with local industrial characteristics.
基金supported by the State Key Development Program for Basic Research of China (Grant Nos. 2007CB512100 and2006CB601007)the National Natural Science Foundation of China (Grant No. 10674006)+2 种基金the National High Technology Research and Development Program of China (Grant No. 2007AA03Z238)China Postdoctoral Science Foundation (Grant No. 20090461376)the Fundamental Research Funds for the Central Universities (Grant No. KYJD09001)
文摘In this paper, we present a magnetocardiogram （MCG） simulation study using the boundary element method （BEM） and based on the virtual heart model and the realistic human volume conductor model. The different contributions of cardiac equivalent source models and volume conductor models to the MCG are deeply and comprehensively investigated. The single dipole source model, the multiple dipoles source model and the equivalent double layer （EDL） source model are analysed and compared with the cardiac equivalent source models. Meanwhile, the effect of the volume conductor model on the MCG combined with these cardiac equivalent sources is investigated. The simulation results demonstrate that the cardiac electrophysiological information will be partly missed when only the single dipole source is taken, while the EDL source is a good option for MCG simulation and the effect of the volume conductor is smallest for the EDL source. Therefore, the EDL source is suitable for the study of MCG forward and inverse problems, and more attention should be paid to it in future MCG studies.
