The effects of process parameters on the microstructural evolution, includinggrain size and volume traction of the a phase during hot forming of a TC6 alloy were investigatedusing compression tests. Experiments were c...The effects of process parameters on the microstructural evolution, includinggrain size and volume traction of the a phase during hot forming of a TC6 alloy were investigatedusing compression tests. Experiments were conducted on the material with (α + β) phases atdeformation temperatures of 800, 860, 920, and 950℃, strain rates of 0.001, 0.01, 1, and 50 s^(-1),and height direction reductions of 30%, 40%, and 50%. After reaching a peak value near 920℃, thegrain size and volume fraction decrease with further increase of deformation temperature. The strainrate affects the morphologies and grain size of α phase of the TC6 titanium alloy. At a lowerstrain rate, the effect of the strain rate on the volume fraction is greater than that at a higherstrain rate under the experimental conditions. The effects of the strain rate on the microstructurealso result from deformation heating. The grain size of the α phase increases with an increase inheight direction reduction after an early drop. The effect of height direction reduction on thevolume fraction is similar to that of the grain size. All of the optical micrographs andquantitative metallography show that deformation process parameters affect the microstructure duringhot forming of the TC6 alloy, and a correlation between the temperature, strain, and strain rateappears to be a significant fuzzy characteristic.展开更多
Magnesium（Mg） alloy AZ31 was produced by continuous variable cross-section direct extrusion（CVCDE）to study its deformation behavior. Metallographic microscopy（OM）, transmission electron microscopy（TEM）, and sc...Magnesium（Mg） alloy AZ31 was produced by continuous variable cross-section direct extrusion（CVCDE）to study its deformation behavior. Metallographic microscopy（OM）, transmission electron microscopy（TEM）, and scanning electron microscopy（SEM） were used to observe the variations in microstructure and fracture morphology of Mg alloy AZ31 as a function of processing methods. The results reveal that grains of Mg alloy AZ31 were refined and their microstructure was homogenized by CVCDE. The recrystallization in Mg alloy AZ31 produced by CVCDE with 2 interim dies was more complete than that produced by conventional extrusion（CE） and CVCDE with 1 interim die, and the grains were finer and more uniform.Plasticity of the AZ31 alloy was improved. Fracture mode was evolved from a combination of ductility and brittleness to a sole ductile form. In summary, a CVCDE mold structure with 2 interim dies can improve microstructure, plasticity, and toughness of Mg alloy AZ31.展开更多
基金This work was financially supported by the Ministry of Science and Technology (No. G2000067206)the Teaching and Research Award Fund for Outstanding Young Teachers in Higher Education Institutions of MOE, China
文摘The effects of process parameters on the microstructural evolution, includinggrain size and volume traction of the a phase during hot forming of a TC6 alloy were investigatedusing compression tests. Experiments were conducted on the material with (α + β) phases atdeformation temperatures of 800, 860, 920, and 950℃, strain rates of 0.001, 0.01, 1, and 50 s^(-1),and height direction reductions of 30%, 40%, and 50%. After reaching a peak value near 920℃, thegrain size and volume fraction decrease with further increase of deformation temperature. The strainrate affects the morphologies and grain size of α phase of the TC6 titanium alloy. At a lowerstrain rate, the effect of the strain rate on the volume fraction is greater than that at a higherstrain rate under the experimental conditions. The effects of the strain rate on the microstructurealso result from deformation heating. The grain size of the α phase increases with an increase inheight direction reduction after an early drop. The effect of height direction reduction on thevolume fraction is similar to that of the grain size. All of the optical micrographs andquantitative metallography show that deformation process parameters affect the microstructure duringhot forming of the TC6 alloy, and a correlation between the temperature, strain, and strain rateappears to be a significant fuzzy characteristic.
基金financial support from the National Natural Science Foundation of China (No. 51675143)
文摘Magnesium（Mg） alloy AZ31 was produced by continuous variable cross-section direct extrusion（CVCDE）to study its deformation behavior. Metallographic microscopy（OM）, transmission electron microscopy（TEM）, and scanning electron microscopy（SEM） were used to observe the variations in microstructure and fracture morphology of Mg alloy AZ31 as a function of processing methods. The results reveal that grains of Mg alloy AZ31 were refined and their microstructure was homogenized by CVCDE. The recrystallization in Mg alloy AZ31 produced by CVCDE with 2 interim dies was more complete than that produced by conventional extrusion（CE） and CVCDE with 1 interim die, and the grains were finer and more uniform.Plasticity of the AZ31 alloy was improved. Fracture mode was evolved from a combination of ductility and brittleness to a sole ductile form. In summary, a CVCDE mold structure with 2 interim dies can improve microstructure, plasticity, and toughness of Mg alloy AZ31.
