Aim To investigate the melting behavior of polyamide 6 in polyamide 6/polyethy lene blends crystallized from amorphous state. Methods DSC was used to test effects of annealing temperature, annealing time, DS...Aim To investigate the melting behavior of polyamide 6 in polyamide 6/polyethy lene blends crystallized from amorphous state. Methods DSC was used to test effects of annealing temperature, annealing time, DSC scan rate, and the step wise annealing on the melting peaks of the ice water quenched specimens. Results and Conclusion Varied melting peaks of PA6 component were obtained. The degree of perfection and the crystallization degree of PA6 crystals decreased in the blends, and the crystallization degree of PA6 increased with the increasing of the annealing time. The height of the upper melting peak of reference PA6 is higher than that in blends.展开更多
The effect of sinter with different MgO contents on the softening-melting behavior of mixed burden made from chro- mium-bearing vanadium-titanium magnetite was investigated. The results show that with increasing MgO c...The effect of sinter with different MgO contents on the softening-melting behavior of mixed burden made from chro- mium-bearing vanadium-titanium magnetite was investigated. The results show that with increasing MgO content in the sinter, the softening interval and melting interval increased and the location of the cohesive zone shifted downward slightly and became moderately thicker. The softening-melting characteristic value was less pronounced when the MgO content in the sinter was 2.98wt%-3.40wt%. Increasing MgO content in the sinter reduced the content and recovery of V and Cr in the dripped iron. In addition, greater MgO contents in the sinter resulted in the generation of greater amounts of high-melting-point components, which adversely affected the permeability of the mixed burden. When the softening-melting behavior of the mixed burden and the recovery of valuable elements were taken into account, proper MgO con- tents in the sinter and slag ranged from 2.98wt% to 3.40wt% and from 11.46wt% to 12.72wt%, respectively, for the smelting of burden made from chromium-bearing vanadium-titanium magnetite in a blast furnace.展开更多
A low MgO content in sinter is conducive to reduce the MgO content in blast furnace slag.This study investigated the effect of MgO content in sinter on the softening–melting behavior of the mixed burden based on flux...A low MgO content in sinter is conducive to reduce the MgO content in blast furnace slag.This study investigated the effect of MgO content in sinter on the softening–melting behavior of the mixed burden based on fluxed pellets.When the MgO content increased from 1.31 wt% to 1.55 wt%, the melting temperature of sinter increased to 1521℃.Such an increase was due to the formation of the high-meltingpoint slag phase.The reduction degradation index of sinter with 1.31 wt% MgO content was better than that of others.The initial softening temperature of the mixed burden increased from 1104 to 1126℃ as MgO content in sinter increased from 1.31 wt% to 1.55 wt%, and the melting temperature decreased from 1494 to 1460℃.The permeability index(S-value) of mixed burden decreased to 594.46 kPa·℃ under a high MgO content with 1.55 wt%, indicating that the permeability was improved.The slag phase composition of burden was mainly akermarite(Ca_(2)MgSiO_(7)) when the MgO content in sinter was 1.55 wt%.The melting point of akermarite is 1450℃, which is lower than other phases.展开更多
Selective laser melting is an additive manufacturing method based on local melting of a metal powder bed by a high power laser beam. Fast laser scans are responsible for severe thermal gradients and high cooling rates...Selective laser melting is an additive manufacturing method based on local melting of a metal powder bed by a high power laser beam. Fast laser scans are responsible for severe thermal gradients and high cooling rates which produce complex hydrodynamic fluid flow. These phenomena affect crystal growth and orientation and are believed to be the cause of material spattering and microstructural defects, e.g. pores and incompletely melted particles. In this work, the microstructure and texture of 316L bars built along two different orientations and the effect of different distribution of defects on their mechanical response and failure mechanisms were investigated. Partially molten powder particles are believed to be responsible for the scattering in elongation to failure, reduced strength, and premature failure of vertical samples.展开更多
A new Nylon 11（PA11）/polyethylene-octene（POE） blends compatibilized by maleic anhydride grafted mixture polyethyleneocten（POE-g-MAH） was prepared through melt blending method.The isothermal crystallization kinet...A new Nylon 11（PA11）/polyethylene-octene（POE） blends compatibilized by maleic anhydride grafted mixture polyethyleneocten（POE-g-MAH） was prepared through melt blending method.The isothermal crystallization kinetics and melting behaviors of PA11/POE blends were investigated in detail by differential scanning calorimetry（DSC） and polarized optical microscope.The n values of PA11 blending with POE or POE-g-MAH are almost similar with pure PA11,which indicates that the effect of POE and POE-g-MAH on nucleation and growth of PA11 crystal is slight.The overall crystallization rate of PA11/POE blends are higher than ones of pure PA11 at the same crystallization temperatures,but they decrease significantly when POE-g-MAH is added into PA11/POE blends.DSC heating curves of both PA11 and its blends exhibit two melting peaks,but the two melting peak become weaker when POE-g-MAH is add into PA11/POE blend systems.And the spherulite size is reduced significantly by the addition of POE-g-MAH compared with pure PA11 and PA11/POE blends.展开更多
The melting behavior of polypropylene (PP) and low ethylene content polypropylenecopolymer with and without nucleating agent samples crystallized under both isothermal and non-isothermal conditions were studied by Dif...The melting behavior of polypropylene (PP) and low ethylene content polypropylenecopolymer with and without nucleating agent samples crystallized under both isothermal and non-isothermal conditions were studied by Differential Scanning Calorimeter (DSC) and X-raydiffraction. Multiple melting behavior were observed depending on the existence of nucleatingagent and crystallization conditions. The observed phenomena have been discussed by the effect ofnucleating agent on perfection of crystal and the melting and recrystallization of imperfect crystalto a more perfect crystal during the heating process of samples.展开更多
The purity of the brazing alloys applied is necessary to be improved with the increasing cleanness of steel. Calcium is easily brought into the widely ased brazing alloy, Ag-Cu-Zn, during the producing process. This p...The purity of the brazing alloys applied is necessary to be improved with the increasing cleanness of steel. Calcium is easily brought into the widely ased brazing alloy, Ag-Cu-Zn, during the producing process. This paper aims at revealing the effect of calcium on the melting behavior of the brazing alloy. The thermal analysis kinetics of silver alloy with trace calcium was studied by using differential scanning calorimetry （ DSC ） , and the enthalpy peaks were analyzed by differential methods. The rate constant of phase transformation in the probable brazing temperature range goes up with increasing calcium content, according to the values of the apparent activation energy, E, and the frequeney constant, A. It is concluded that the calcium addition could improve the melting performance of Ag-Cu-Zn brazing alloy.展开更多
In this study, a series of monodispersed poly（L-lactide）（PLLA） were synthesized by the ring-opening polymerization with Schiff base aluminum catalyst, and the effects of the number-average molecular weight（Mn） o...In this study, a series of monodispersed poly（L-lactide）（PLLA） were synthesized by the ring-opening polymerization with Schiff base aluminum catalyst, and the effects of the number-average molecular weight（Mn） on the crystallization and melting behaviors of PLLA were investigated by differential scanning calorimetry（DSC） and wide-angle X-ray diffraction（WAXD）. The total crystallization rate of PLLA was Mn-dependent, which reached the maximum value for PLLA with Mn of 18.6 kg/mol. In addition, when Mn of PLLA was 18.6 kg/mol, the melting enthalpy（ΔHm） showed a maximum value（87.1 J/g）, which was the highest reported value till now. The critical temperature for change of crystal formation from ？-form to ？-form crystals increased in the isothermal crystallization process with Mn increasing. In the reheating procedure, high-Mn PLLA demonstrated a small exothermal peak prior to the dominant melting peak, corresponding to crystal transition from ？- to ？-form, but low-Mn PLLA didn＇t show the peak of crystal transition. These different crystallization and melting behaviors were attributed to the different chain mobility of PLLA with different Mn.展开更多
In this study, the effect of melting temperature on the microstructural evolutions, behavior, and corrosion morphology of Hadfield steel in the casting process is investigated. The mold was prepared by the sodium sili...In this study, the effect of melting temperature on the microstructural evolutions, behavior, and corrosion morphology of Hadfield steel in the casting process is investigated. The mold was prepared by the sodium silicate/CO_2 method, using a blind riser, and then the desired molten steel was obtained using a coreless induction furnace. The casting was performed at melting temperatures of 1350, 1400, 1450, and 1500°C, and the cast blocks were immediately quenched in water. Optical microscopy was used to analyze the microstructure, and scanning electron microscopy(SEM) and X-ray diffractrometry(XRD) were used to analyze the corrosion morphology and phase formation in the microstructure, respectively. The corrosion behavior of the samples was analyzed using a potentiodynamic polarization test and electrochemical impedance spectroscopy(EIS) in 3.5 wt% NaCl. The optical microscopy observations and XRD patterns show that the increase in melting temperature led to a decrease of carbides and an increase in the austenite grain size in the Hadfield steel microstructure. The corrosion tests results show that with increasing melting temperature in the casting process, Hadfield steel shows a higher corrosion resistance. The SEM images of the corrosion morphologies show that the reduction of melting temperature in the Hadfield steel casting process induced micro-galvanic corrosion conditions.展开更多
Based on the molecular theory of non-linear viscoelasticity with constrained entanglements in polymer melts, the material functions in simple shear flow were formulated, the theoretical relations between. eta((gamma) ...Based on the molecular theory of non-linear viscoelasticity with constrained entanglements in polymer melts, the material functions in simple shear flow were formulated, the theoretical relations between. eta((gamma) over dot), psi (10)((gamma) over dot) and shear rate ((gamma) over dot), and topologically constrained dimension number n ' and a were derived. Linear viscoelastic parameters (eta (0) and G(N)(0)) and topologically constrained dimension number (n ' a and <(<upsilon>)over bar>) as a function of the primary molecular weight (M-n), molecular weight between entanglements (M-C) and the entanglement sites sequence distribution in polymer chain were determined. A new method for determination of viscoelastic parameters (eta (0), psi (10), G(N)(0) and J(e)(0)), topologically constrained dimension number (n ', a and v) and molecular weight (M-n, M-c and M-e) from the shear flow measurements was proposed. It was used to determine those parameters and structures of HDPE, making a good agreement between these values and those obtained by other methods. The agreement affords a quantitative verification for the molecular theory of nonlinear viscoelasticity with constrained entanglement in polymer melts.展开更多
Direct reduction of low-grade lateritic bauxite was studied at high temperature to recover Fe and beneficiate AlzO3 slag. The re- sults show that a metallization rate of 97.9% and a nugget recovery rate of 85.1% can b...Direct reduction of low-grade lateritic bauxite was studied at high temperature to recover Fe and beneficiate AlzO3 slag. The re- sults show that a metallization rate of 97.9% and a nugget recovery rate of 85.1% can be achieved when the reducing and melting tempera- tures are 1350 and 1480℃, respectively. Moreover, a higher-grade calcium aluminate slag （A1203 = 50.52wt%） can also be obtained, which is mainly composed of ct-A1203, hercynite （FeAI：O4）, and gehlenite （Ca2A12SiO7）. In addition, high-quality iron nuggets have been produced from low-grade lateritic bauxite. The nugget is mainly composed of iron （93.82wt%） and carbon （3.86wt%）, with almost no gangue （slag）.展开更多
The samples were fabricated by 220 t thixomolded machine made by Japan Steel Works. The microstructure from the AZ91D magnesium alloy chips to the thixomolded products was investigated. Melting behavior of the chips i...The samples were fabricated by 220 t thixomolded machine made by Japan Steel Works. The microstructure from the AZ91D magnesium alloy chips to the thixomolded products was investigated. Melting behavior of the chips in thixomolding process was analyzed. The evolution processing of solid phase morphology was studied,and evolution model was put forward. The results show that microstructures in outer zone of a chip and the inner zone are obviously different,and the severe distortion takes place in the brim of the chip,where the grains are observed to be bent,distorted,even broken. The severe plastic deformation region is firstly molten,then segregation area in the inner of the chip continues to melt. The liquid phase in solid phase does not formed by liquid entrapped during shearing process,but primarily induced by internal composition segregation.展开更多
Aβ-solidifying Ti-40 Al-9 V-0.5 Y(at.%)alloy with a high cracking sensitivity has been successfully fabricated by selective laser melting(SLM)in this study.The influence factors for cracking sensitivity,cracking beha...Aβ-solidifying Ti-40 Al-9 V-0.5 Y(at.%)alloy with a high cracking sensitivity has been successfully fabricated by selective laser melting(SLM)in this study.The influence factors for cracking sensitivity,cracking behavior and crack inhibition mechanism were investigated.The results show that the effects of process parameters on cracking sensitivity strongly depend on the cooling rate in molten pool with different heat transfer modes.The conduction mode with higher cooling rates exhibits a higher cracking sensitivity in comparison to the keyhole mode.Microstructure characteristics and phase transformations controlled by cooling rate determine the inherent ductility ofβ-solidifyingγ-Ti Al alloys during SLM.On this basis,the formation and inhibition mechanism of solidification and cold cracking are proposed.Finally,the crackfree Ti-40 Al-9 V-0.5 Y sample with fine equiaxed microstructures and favorable mechanical properties(microhardness of 542±19 HV,yield strength of 1871±12 MPa,ultimate strength of 2106±13 MPa and ultimate compressive strain of 10.89±0.57%)can be produced by SLM.The strengthening mechanism can be attributed to grain refinement and precipitation strengthening.展开更多
By introducing a vibrating force field into the extrusion process of polymer melt, an experimental equipment of constant velocity type dynamic rheometer of capillary (CVDRC) was designed. A set of experimental procedu...By introducing a vibrating force field into the extrusion process of polymer melt, an experimental equipment of constant velocity type dynamic rheometer of capillary (CVDRC) was designed. A set of experimental procedures was established, by which the dynamic rheological parameters of polymer can be acquired, and a set of data management methods to undergo time-domain or frequency-domain analysis was set up for dynamic rheological data of polymer melt. Meantime, the characterization formula of polymer melt's rheological behavior in a vibrating force field was set up. The instantaneous value of capillary entry pressure, capillary volume flow rate and their phase difference were measured and analyzed, and the melt apparent viscosity, which describes the rheological behavior of polymer melt in a vibrating force field, was obtained.展开更多
An approach with statistical mechanics and a unified molecular theory of non-linearviscoelasticity with constraints of Gaussian chain entanglement for polymer melts were proposed.Amultimode model structure for a singl...An approach with statistical mechanics and a unified molecular theory of non-linearviscoelasticity with constraints of Gaussian chain entanglement for polymer melts were proposed.Amultimode model structure for a single polymer chain with tail segments and N reversibleentanglement sites on the test polymer chain was developed.The probability distribution function ofthe end-to-end vector for a single polymer chain at entangled state and the viscoelastic free energyof deformation for polymer melts were calculated.Four types of stress-strain relationship and mem-ory function were derived from this theory.The above theoretical relationships were verified by experi-mental data of PS(polystyrene)and LDPE(low density polyethylene)melts.展开更多
Continental intraplate basalts form by partial melting of the mantle,and can provide important constraints on mantle heterogeneity.However,due to the thick overlying continental lithosphere,the origins of the geochemi...Continental intraplate basalts form by partial melting of the mantle,and can provide important constraints on mantle heterogeneity.However,due to the thick overlying continental lithosphere,the origins of the geochemical characteristics of continental intraplate basalts are controversial.In this study,we examined the geochemistry of Cenozoic basalts in southeast China.These basalts which are divided into four volcanic belts exhibit a DMM-EM2 mixing trend and spatial variations in Pb isotopes from inland(i.e.,thick lithosphere)to coastal(i.e.,thin lithosphere)regions.In contrast to the Pb isotopic variations,there are no spatial variations in Sr-Nd-Hf isotopes.Marked correlations between Pb isotopes and major elements(i.e.,Mg O and Si O_(2))suggest the continental lithospheric lid controlled their petrogenesis.Nonetheless,other factors are needed to explain the variations in Ti/Ti^(*)and Hf/Hf^(*)ratios,and Nd-Hf isotopes of the southeast China basalts.The increasing Pb isotope ratios from the inner to coastal regions are associated with decreases in CaO/Al_(2)O_(3) ratios and increases in FC3MS(FeO^(T)/CaO-3×Mg O/Si O_(2);in wt.%)values,indicating contributions from non-peridotite components in the mantle sources.The similarly depleted Nd-Hf isotopic compositions of the basalts from the three inner belts indicate these basalts have a similar origin,whereas the more enriched isotopic features of the basalts from the outer belt suggest their mantle source contains older recycled oceanic crust.Thus,source(i.e.,lithological)heterogeneity also had a significant role in controlling the geochemistry of these basalts.The DMM-EM2 mixing trend defined by the Pb isotopic compositions of continental intraplate basalts from southeast China was generated by variable degrees of melting of heterogeneous mantle that was controlled by the thickness of the continental lithospheric lid(i.e.,the melting pressure).This caused variable extents of melting of enriched components in the mantle sources of the basalts(i.e.,carbonated peridotite vs.pyroxenite).展开更多
激光粉末床熔融(Laser Powder Bed Fusion,LPBF)技术是定制化多孔纯Mo结构的重要技术。然而,LPBF成形纯Mo试样仍面临表面粗糙度值高及耐蚀性差等问题。电化学抛光(Electrochemical Polishing,ECP)是LPBF成形纯Mo的主要环保型后处理工艺...激光粉末床熔融(Laser Powder Bed Fusion,LPBF)技术是定制化多孔纯Mo结构的重要技术。然而,LPBF成形纯Mo试样仍面临表面粗糙度值高及耐蚀性差等问题。电化学抛光(Electrochemical Polishing,ECP)是LPBF成形纯Mo的主要环保型后处理工艺。研究了不同ECP抛光状态对LPBF成形纯Mo的表面粗糙度及降解特性的影响。结果表明:经电化学抛光处理后,试样表面粗糙度由4.55μm显著降低至1.05μm;相比原始态试样,抛光后试样腐蚀电流密度降低了78.4%。失重率从大到小顺序为:原始态>半抛光>抛光,且随着浸泡时间增加,失重率逐渐增加。溶液pH值波动≤0.5,验证了降解过程未引发局部酸化,符合生物医用材料要求。通过采用ECP处理Mo基材料表面,为合理调控其植入体的降解行为及降解速率的均匀性提供了重要理论依据。展开更多
文摘Aim To investigate the melting behavior of polyamide 6 in polyamide 6/polyethy lene blends crystallized from amorphous state. Methods DSC was used to test effects of annealing temperature, annealing time, DSC scan rate, and the step wise annealing on the melting peaks of the ice water quenched specimens. Results and Conclusion Varied melting peaks of PA6 component were obtained. The degree of perfection and the crystallization degree of PA6 crystals decreased in the blends, and the crystallization degree of PA6 increased with the increasing of the annealing time. The height of the upper melting peak of reference PA6 is higher than that in blends.
基金the National Natural Science Foundation of China (51574067)the National High Technology Research and Development Program of China (2012AA062302 and 2012AA062304)the Fundamental Research Funds for the Central Universities of China (N110202001)
文摘The effect of sinter with different MgO contents on the softening-melting behavior of mixed burden made from chro- mium-bearing vanadium-titanium magnetite was investigated. The results show that with increasing MgO content in the sinter, the softening interval and melting interval increased and the location of the cohesive zone shifted downward slightly and became moderately thicker. The softening-melting characteristic value was less pronounced when the MgO content in the sinter was 2.98wt%-3.40wt%. Increasing MgO content in the sinter reduced the content and recovery of V and Cr in the dripped iron. In addition, greater MgO contents in the sinter resulted in the generation of greater amounts of high-melting-point components, which adversely affected the permeability of the mixed burden. When the softening-melting behavior of the mixed burden and the recovery of valuable elements were taken into account, proper MgO con- tents in the sinter and slag ranged from 2.98wt% to 3.40wt% and from 11.46wt% to 12.72wt%, respectively, for the smelting of burden made from chromium-bearing vanadium-titanium magnetite in a blast furnace.
基金financially supported by the Fundamental Research Funds for the Central Universities, China (No.06500170)the Guangdong Basic and Applied Basic Research Foundation, China (No.2020A1515111008)。
文摘A low MgO content in sinter is conducive to reduce the MgO content in blast furnace slag.This study investigated the effect of MgO content in sinter on the softening–melting behavior of the mixed burden based on fluxed pellets.When the MgO content increased from 1.31 wt% to 1.55 wt%, the melting temperature of sinter increased to 1521℃.Such an increase was due to the formation of the high-meltingpoint slag phase.The reduction degradation index of sinter with 1.31 wt% MgO content was better than that of others.The initial softening temperature of the mixed burden increased from 1104 to 1126℃ as MgO content in sinter increased from 1.31 wt% to 1.55 wt%, and the melting temperature decreased from 1494 to 1460℃.The permeability index(S-value) of mixed burden decreased to 594.46 kPa·℃ under a high MgO content with 1.55 wt%, indicating that the permeability was improved.The slag phase composition of burden was mainly akermarite(Ca_(2)MgSiO_(7)) when the MgO content in sinter was 1.55 wt%.The melting point of akermarite is 1450℃, which is lower than other phases.
文摘Selective laser melting is an additive manufacturing method based on local melting of a metal powder bed by a high power laser beam. Fast laser scans are responsible for severe thermal gradients and high cooling rates which produce complex hydrodynamic fluid flow. These phenomena affect crystal growth and orientation and are believed to be the cause of material spattering and microstructural defects, e.g. pores and incompletely melted particles. In this work, the microstructure and texture of 316L bars built along two different orientations and the effect of different distribution of defects on their mechanical response and failure mechanisms were investigated. Partially molten powder particles are believed to be responsible for the scattering in elongation to failure, reduced strength, and premature failure of vertical samples.
文摘A new Nylon 11（PA11）/polyethylene-octene（POE） blends compatibilized by maleic anhydride grafted mixture polyethyleneocten（POE-g-MAH） was prepared through melt blending method.The isothermal crystallization kinetics and melting behaviors of PA11/POE blends were investigated in detail by differential scanning calorimetry（DSC） and polarized optical microscope.The n values of PA11 blending with POE or POE-g-MAH are almost similar with pure PA11,which indicates that the effect of POE and POE-g-MAH on nucleation and growth of PA11 crystal is slight.The overall crystallization rate of PA11/POE blends are higher than ones of pure PA11 at the same crystallization temperatures,but they decrease significantly when POE-g-MAH is added into PA11/POE blends.DSC heating curves of both PA11 and its blends exhibit two melting peaks,but the two melting peak become weaker when POE-g-MAH is add into PA11/POE blend systems.And the spherulite size is reduced significantly by the addition of POE-g-MAH compared with pure PA11 and PA11/POE blends.
文摘The melting behavior of polypropylene (PP) and low ethylene content polypropylenecopolymer with and without nucleating agent samples crystallized under both isothermal and non-isothermal conditions were studied by Differential Scanning Calorimeter (DSC) and X-raydiffraction. Multiple melting behavior were observed depending on the existence of nucleatingagent and crystallization conditions. The observed phenomena have been discussed by the effect ofnucleating agent on perfection of crystal and the melting and recrystallization of imperfect crystalto a more perfect crystal during the heating process of samples.
文摘The purity of the brazing alloys applied is necessary to be improved with the increasing cleanness of steel. Calcium is easily brought into the widely ased brazing alloy, Ag-Cu-Zn, during the producing process. This paper aims at revealing the effect of calcium on the melting behavior of the brazing alloy. The thermal analysis kinetics of silver alloy with trace calcium was studied by using differential scanning calorimetry （ DSC ） , and the enthalpy peaks were analyzed by differential methods. The rate constant of phase transformation in the probable brazing temperature range goes up with increasing calcium content, according to the values of the apparent activation energy, E, and the frequeney constant, A. It is concluded that the calcium addition could improve the melting performance of Ag-Cu-Zn brazing alloy.
基金financially supported by the National Natural Science Foundation of China(Nos.5130317651373169+3 种基金5103300351473166 and 51403089)Innovative Research Group(No.51321062)The National High-tech R&D Program of China(863 program)(No.2011AA02A202)
文摘In this study, a series of monodispersed poly（L-lactide）（PLLA） were synthesized by the ring-opening polymerization with Schiff base aluminum catalyst, and the effects of the number-average molecular weight（Mn） on the crystallization and melting behaviors of PLLA were investigated by differential scanning calorimetry（DSC） and wide-angle X-ray diffraction（WAXD）. The total crystallization rate of PLLA was Mn-dependent, which reached the maximum value for PLLA with Mn of 18.6 kg/mol. In addition, when Mn of PLLA was 18.6 kg/mol, the melting enthalpy（ΔHm） showed a maximum value（87.1 J/g）, which was the highest reported value till now. The critical temperature for change of crystal formation from ？-form to ？-form crystals increased in the isothermal crystallization process with Mn increasing. In the reheating procedure, high-Mn PLLA demonstrated a small exothermal peak prior to the dominant melting peak, corresponding to crystal transition from ？- to ？-form, but low-Mn PLLA didn＇t show the peak of crystal transition. These different crystallization and melting behaviors were attributed to the different chain mobility of PLLA with different Mn.
文摘In this study, the effect of melting temperature on the microstructural evolutions, behavior, and corrosion morphology of Hadfield steel in the casting process is investigated. The mold was prepared by the sodium silicate/CO_2 method, using a blind riser, and then the desired molten steel was obtained using a coreless induction furnace. The casting was performed at melting temperatures of 1350, 1400, 1450, and 1500°C, and the cast blocks were immediately quenched in water. Optical microscopy was used to analyze the microstructure, and scanning electron microscopy(SEM) and X-ray diffractrometry(XRD) were used to analyze the corrosion morphology and phase formation in the microstructure, respectively. The corrosion behavior of the samples was analyzed using a potentiodynamic polarization test and electrochemical impedance spectroscopy(EIS) in 3.5 wt% NaCl. The optical microscopy observations and XRD patterns show that the increase in melting temperature led to a decrease of carbides and an increase in the austenite grain size in the Hadfield steel microstructure. The corrosion tests results show that with increasing melting temperature in the casting process, Hadfield steel shows a higher corrosion resistance. The SEM images of the corrosion morphologies show that the reduction of melting temperature in the Hadfield steel casting process induced micro-galvanic corrosion conditions.
基金The authors gratefully a.cknowledge financial supportfrom th6 Natiol-al Natural Science Foundatiol- of CI-h-a. The number of
文摘Based on the molecular theory of non-linear viscoelasticity with constrained entanglements in polymer melts, the material functions in simple shear flow were formulated, the theoretical relations between. eta((gamma) over dot), psi (10)((gamma) over dot) and shear rate ((gamma) over dot), and topologically constrained dimension number n ' and a were derived. Linear viscoelastic parameters (eta (0) and G(N)(0)) and topologically constrained dimension number (n ' a and <(<upsilon>)over bar>) as a function of the primary molecular weight (M-n), molecular weight between entanglements (M-C) and the entanglement sites sequence distribution in polymer chain were determined. A new method for determination of viscoelastic parameters (eta (0), psi (10), G(N)(0) and J(e)(0)), topologically constrained dimension number (n ', a and v) and molecular weight (M-n, M-c and M-e) from the shear flow measurements was proposed. It was used to determine those parameters and structures of HDPE, making a good agreement between these values and those obtained by other methods. The agreement affords a quantitative verification for the molecular theory of nonlinear viscoelasticity with constrained entanglement in polymer melts.
基金financially supported by the International Scientific and Technological Cooperation and Exchange Projects of China (No. 2013DFG50640)
文摘Direct reduction of low-grade lateritic bauxite was studied at high temperature to recover Fe and beneficiate AlzO3 slag. The re- sults show that a metallization rate of 97.9% and a nugget recovery rate of 85.1% can be achieved when the reducing and melting tempera- tures are 1350 and 1480℃, respectively. Moreover, a higher-grade calcium aluminate slag （A1203 = 50.52wt%） can also be obtained, which is mainly composed of ct-A1203, hercynite （FeAI：O4）, and gehlenite （Ca2A12SiO7）. In addition, high-quality iron nuggets have been produced from low-grade lateritic bauxite. The nugget is mainly composed of iron （93.82wt%） and carbon （3.86wt%）, with almost no gangue （slag）.
基金Project (2007101) supported by the Science and Technology Development Program of Changchun University of Technology, China
文摘The samples were fabricated by 220 t thixomolded machine made by Japan Steel Works. The microstructure from the AZ91D magnesium alloy chips to the thixomolded products was investigated. Melting behavior of the chips in thixomolding process was analyzed. The evolution processing of solid phase morphology was studied,and evolution model was put forward. The results show that microstructures in outer zone of a chip and the inner zone are obviously different,and the severe distortion takes place in the brim of the chip,where the grains are observed to be bent,distorted,even broken. The severe plastic deformation region is firstly molten,then segregation area in the inner of the chip continues to melt. The liquid phase in solid phase does not formed by liquid entrapped during shearing process,but primarily induced by internal composition segregation.
基金supported financially by the Pre-research Fund Project of Ministry of Equipment and Development of China(No.61409230301)the Fundamental Research Funds for the Central Universities through Program no.2019kfyXMPY005 and no.2019kfyXKJC042.
文摘Aβ-solidifying Ti-40 Al-9 V-0.5 Y(at.%)alloy with a high cracking sensitivity has been successfully fabricated by selective laser melting(SLM)in this study.The influence factors for cracking sensitivity,cracking behavior and crack inhibition mechanism were investigated.The results show that the effects of process parameters on cracking sensitivity strongly depend on the cooling rate in molten pool with different heat transfer modes.The conduction mode with higher cooling rates exhibits a higher cracking sensitivity in comparison to the keyhole mode.Microstructure characteristics and phase transformations controlled by cooling rate determine the inherent ductility ofβ-solidifyingγ-Ti Al alloys during SLM.On this basis,the formation and inhibition mechanism of solidification and cold cracking are proposed.Finally,the crackfree Ti-40 Al-9 V-0.5 Y sample with fine equiaxed microstructures and favorable mechanical properties(microhardness of 542±19 HV,yield strength of 1871±12 MPa,ultimate strength of 2106±13 MPa and ultimate compressive strain of 10.89±0.57%)can be produced by SLM.The strengthening mechanism can be attributed to grain refinement and precipitation strengthening.
文摘By introducing a vibrating force field into the extrusion process of polymer melt, an experimental equipment of constant velocity type dynamic rheometer of capillary (CVDRC) was designed. A set of experimental procedures was established, by which the dynamic rheological parameters of polymer can be acquired, and a set of data management methods to undergo time-domain or frequency-domain analysis was set up for dynamic rheological data of polymer melt. Meantime, the characterization formula of polymer melt's rheological behavior in a vibrating force field was set up. The instantaneous value of capillary entry pressure, capillary volume flow rate and their phase difference were measured and analyzed, and the melt apparent viscosity, which describes the rheological behavior of polymer melt in a vibrating force field, was obtained.
基金This work was supported by the National Natural Science Education Committee Foundation of China and the National Natural Science Foundation of China
文摘An approach with statistical mechanics and a unified molecular theory of non-linearviscoelasticity with constraints of Gaussian chain entanglement for polymer melts were proposed.Amultimode model structure for a single polymer chain with tail segments and N reversibleentanglement sites on the test polymer chain was developed.The probability distribution function ofthe end-to-end vector for a single polymer chain at entangled state and the viscoelastic free energyof deformation for polymer melts were calculated.Four types of stress-strain relationship and mem-ory function were derived from this theory.The above theoretical relationships were verified by experi-mental data of PS(polystyrene)and LDPE(low density polyethylene)melts.
基金supported by the National Natural Science Foundation of China(No.41906051)the National Key R&D Program of China(No.2018YFE0202402)+1 种基金sponsored by the Fundamental Research Funds for the Central Universities(Tongji University)(No.22120210525)Shanghai Pilot Program for Basic Research。
文摘Continental intraplate basalts form by partial melting of the mantle,and can provide important constraints on mantle heterogeneity.However,due to the thick overlying continental lithosphere,the origins of the geochemical characteristics of continental intraplate basalts are controversial.In this study,we examined the geochemistry of Cenozoic basalts in southeast China.These basalts which are divided into four volcanic belts exhibit a DMM-EM2 mixing trend and spatial variations in Pb isotopes from inland(i.e.,thick lithosphere)to coastal(i.e.,thin lithosphere)regions.In contrast to the Pb isotopic variations,there are no spatial variations in Sr-Nd-Hf isotopes.Marked correlations between Pb isotopes and major elements(i.e.,Mg O and Si O_(2))suggest the continental lithospheric lid controlled their petrogenesis.Nonetheless,other factors are needed to explain the variations in Ti/Ti^(*)and Hf/Hf^(*)ratios,and Nd-Hf isotopes of the southeast China basalts.The increasing Pb isotope ratios from the inner to coastal regions are associated with decreases in CaO/Al_(2)O_(3) ratios and increases in FC3MS(FeO^(T)/CaO-3×Mg O/Si O_(2);in wt.%)values,indicating contributions from non-peridotite components in the mantle sources.The similarly depleted Nd-Hf isotopic compositions of the basalts from the three inner belts indicate these basalts have a similar origin,whereas the more enriched isotopic features of the basalts from the outer belt suggest their mantle source contains older recycled oceanic crust.Thus,source(i.e.,lithological)heterogeneity also had a significant role in controlling the geochemistry of these basalts.The DMM-EM2 mixing trend defined by the Pb isotopic compositions of continental intraplate basalts from southeast China was generated by variable degrees of melting of heterogeneous mantle that was controlled by the thickness of the continental lithospheric lid(i.e.,the melting pressure).This caused variable extents of melting of enriched components in the mantle sources of the basalts(i.e.,carbonated peridotite vs.pyroxenite).
文摘激光粉末床熔融(Laser Powder Bed Fusion,LPBF)技术是定制化多孔纯Mo结构的重要技术。然而,LPBF成形纯Mo试样仍面临表面粗糙度值高及耐蚀性差等问题。电化学抛光(Electrochemical Polishing,ECP)是LPBF成形纯Mo的主要环保型后处理工艺。研究了不同ECP抛光状态对LPBF成形纯Mo的表面粗糙度及降解特性的影响。结果表明:经电化学抛光处理后,试样表面粗糙度由4.55μm显著降低至1.05μm;相比原始态试样,抛光后试样腐蚀电流密度降低了78.4%。失重率从大到小顺序为:原始态>半抛光>抛光,且随着浸泡时间增加,失重率逐渐增加。溶液pH值波动≤0.5,验证了降解过程未引发局部酸化,符合生物医用材料要求。通过采用ECP处理Mo基材料表面,为合理调控其植入体的降解行为及降解速率的均匀性提供了重要理论依据。
